Search Results

Search found 16530 results on 662 pages for 'off shore'.

Page 582/662 | < Previous Page | 578 579 580 581 582 583 584 585 586 587 588 589  | Next Page >

• ESXi 5.1 ghettoVCB stuck at Clone: 10% done

  - by stormdrain

  Trying to run ghettoVCB for the first time here. I am using a NAS that is set up as a datastore on the host. I did a dry run and it completed without error. The VM is ~500GB and there is only one on the host that I'm trying to backup. I proceeded to start the actual backup: ./ghettoVCB.sh -m vmname -g ghettoVCB.conf It goes though the config and looks like it's taking off: 2013-10-24 11:43:19 -- info: CONFIG - USING GLOBAL GHETTOVCB CONFIGURATION FILE = ghettoVCB.conf 2013-10-24 11:43:19 -- info: CONFIG - VERSION = 2013_01_11_0 2013-10-24 11:43:19 -- info: CONFIG - GHETTOVCB_PID = 17398616 2013-10-24 11:43:19 -- info: CONFIG - VM_BACKUP_VOLUME = /vmfs/volumes/nas2tb-001/esxi4 2013-10-24 11:43:19 -- info: CONFIG - VM_BACKUP_ROTATION_COUNT = 3 2013-10-24 11:43:19 -- info: CONFIG - VM_BACKUP_DIR_NAMING_CONVENTION = 2013-10-24_11-43-18 2013-10-24 11:43:19 -- info: CONFIG - DISK_BACKUP_FORMAT = thin 2013-10-24 11:43:19 -- info: CONFIG - POWER_VM_DOWN_BEFORE_BACKUP = 0 2013-10-24 11:43:19 -- info: CONFIG - ENABLE_HARD_POWER_OFF = 0 2013-10-24 11:43:19 -- info: CONFIG - ITER_TO_WAIT_SHUTDOWN = 4 2013-10-24 11:43:19 -- info: CONFIG - POWER_DOWN_TIMEOUT = 5 2013-10-24 11:43:19 -- info: CONFIG - SNAPSHOT_TIMEOUT = 15 2013-10-24 11:43:19 -- info: CONFIG - LOG_LEVEL = info 2013-10-24 11:43:19 -- info: CONFIG - BACKUP_LOG_OUTPUT = /tmp/ghettoVCB-2013-10-24_11-43-18-17398616.log 2013-10-24 11:43:19 -- info: CONFIG - ENABLE_COMPRESSION = 0 2013-10-24 11:43:19 -- info: CONFIG - VM_SNAPSHOT_MEMORY = 0 2013-10-24 11:43:19 -- info: CONFIG - VM_SNAPSHOT_QUIESCE = 0 2013-10-24 11:43:19 -- info: CONFIG - ALLOW_VMS_WITH_SNAPSHOTS_TO_BE_BACKEDUP = 0 2013-10-24 11:43:19 -- info: CONFIG - VMDK_FILES_TO_BACKUP = all 2013-10-24 11:43:19 -- info: CONFIG - VM_SHUTDOWN_ORDER = 2013-10-24 11:43:19 -- info: CONFIG - VM_STARTUP_ORDER = 2013-10-24 11:43:19 -- info: CONFIG - EMAIL_LOG = 0 2013-10-24 11:43:19 -- info: 2013-10-24 11:43:22 -- info: Initiate backup for vmname 2013-10-24 11:43:22 -- info: Creating Snapshot "ghettoVCB-snapshot-2013-10-24" for serv2 Destination disk format: VMFS thin-provisioned Cloning disk '/vmfs/volumes/esxi4-storage/vmname/vmname_1.vmdk'... Clone: 10% done. and it's been that way for over an hour now. Stuck at Clone: 10% done.. Thing is: I can see the vmdk on the NAS. And it looks like almost the whole thing is there. On the NAS it's showing ~430GB but on vSphere Client Summary is shows as 507GB. I don't see the vmdk on the NAS growing any more. The logfile mimics some of the above and is sitting at "Creating Snapshot..." and nothing else is coming in. Is the vmdk on the NAS showing all those GB because of the provisioning or something? i.e. is the size of the file not necessarily indicative of the amount of actual data that has been copied? Is there are reason it might be "Stuck" at 10%? i.e. could it really be taking this long? Any other tips? Thanks. Edit: as soon as I hit the Submit button, I glance over to see that it has incremented to 11% done. Good to know it'll be complete sometime around when the sun explodes.

  Read the article

• "The system time has changed" avents after waking from sleep

  - by Damir Arh

  Sometimes when my computer running Windows 7 wakes up from sleep, it has to adjust the time. When this happens the following system event is logged: <Event xmlns='http://schemas.microsoft.com/win/2004/08/events/event'> <System> <Provider Name='Microsoft-Windows-Kernel-General' Guid='{A68CA8B7-004F-D7B6-A698-07E2DE0F1F5D}'/> <EventID>1</EventID> <Version>0</Version> <Level>4</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x8000000000000010</Keywords> <TimeCreated SystemTime='2010-03-06T19:09:57.500000000Z'/> <EventRecordID>10672</EventRecordID> <Correlation/> <Execution ProcessID='4' ThreadID='56'/> <Channel>System</Channel> <Computer>GAME</Computer> <Security/> </System> <EventData> <Data Name='NewTime'>2010-03-06T19:09:57.500000000Z</Data> <Data Name='OldTime'>2010-03-06T17:34:32.870117200Z</Data> </EventData> <RenderingInfo Culture='sl-SI'> <Message>The system time has changed to ?2010?-?03?-?06T19:09:57.500000000Z from ?2010?-?03?-?06T17:34:32.870117200Z.</Message> <Level>Information</Level> <Task></Task> <Opcode>Info</Opcode> <Channel>System</Channel> <Provider>Microsoft-Windows-Kernel-General</Provider> <Keywords> <Keyword>Time</Keyword> </Keywords> </RenderingInfo> </Event> When this happens (I noticed it twice until now) the old time always corresponds to the time when computer entered sleep. The problem is that if Windows Media Center is scheduled for recording during this time, it just skips it as if the computer was turned off. I never had this problem running Windows Vista on the same machine. Any ideas what could be causing this problem and how to solve it are welcome.

  Read the article

• Linux Software RAID recovery

  - by Zoredache

  I am seeing a discrepancy between the output of mdadm --detail and mdadm --examine, and I don't understand why. This output mdadm --detail /dev/md2 /dev/md2: Version : 0.90 Creation Time : Wed Mar 14 18:20:52 2012 Raid Level : raid10 Array Size : 3662760640 (3493.08 GiB 3750.67 GB) Used Dev Size : 1465104256 (1397.23 GiB 1500.27 GB) Raid Devices : 5 Total Devices : 5 Preferred Minor : 2 Persistence : Superblock is persistent Seems to contradict this. (the same for every disk in the array) mdadm --examine /dev/sdc2 /dev/sdc2: Magic : a92b4efc Version : 0.90.00 UUID : 1f54d708:60227dd6:163c2a05:89fa2e07 (local to host) Creation Time : Wed Mar 14 18:20:52 2012 Raid Level : raid10 Used Dev Size : 1465104320 (1397.23 GiB 1500.27 GB) Array Size : 2930208640 (2794.46 GiB 3000.53 GB) Raid Devices : 5 Total Devices : 5 Preferred Minor : 2 The array was created like this. mdadm -v --create /dev/md2 \ --level=raid10 --layout=o2 --raid-devices=5 \ --chunk=64 --metadata=0.90 \ /dev/sdg2 /dev/sdf2 /dev/sde2 /dev/sdd2 /dev/sdc2 Each of the 5 individual drives have partitions like this. Disk /dev/sdc: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057754 Device Boot Start End Blocks Id System /dev/sdc1 2048 34815 16384 83 Linux /dev/sdc2 34816 2930243583 1465104384 fd Linux raid autodetect Backstory So the SATA controller failed in a box I provide some support for. The failure was a ugly and so individual drives fell out of the array a little at a time. While there are backups, we the are not really done as frequently as we really need. There is some data that I am trying to recover if I can. I got additional hardware and I was able to access the drives again. The drives appear to be fine, and I can get the array and filesystem active and mounted (using read-only mode). I am able to access some data on the filesystem and have been copying that off, but I am seeing lots of errors when I try to copy the most recent data. When I am trying to access that most recent data I am getting errors like below which makes me think that the array size discrepancy may be the problem. Mar 14 18:26:04 server kernel: [351588.196299] dm-7: rw=0, want=6619839616, limit=6442450944 Mar 14 18:26:04 server kernel: [351588.196309] attempt to access beyond end of device Mar 14 18:26:04 server kernel: [351588.196313] dm-7: rw=0, want=6619839616, limit=6442450944 Mar 14 18:26:04 server kernel: [351588.199260] attempt to access beyond end of device Mar 14 18:26:04 server kernel: [351588.199264] dm-7: rw=0, want=20647626304, limit=6442450944 Mar 14 18:26:04 server kernel: [351588.202446] attempt to access beyond end of device Mar 14 18:26:04 server kernel: [351588.202450] dm-7: rw=0, want=19973212288, limit=6442450944 Mar 14 18:26:04 server kernel: [351588.205516] attempt to access beyond end of device Mar 14 18:26:04 server kernel: [351588.205520] dm-7: rw=0, want=8009695096, limit=6442450944

  Read the article

• tproxy squid bridge very slow when cache is full

  - by Roberto

  I have installed a bridge tproxy proxy in a fast server with 8GB ram. The traffic is around 60Mb/s. When I start for first time the proxy (with the cache empty) the proxy works very well but when the cache becomes full (few hours later) the bridge goes very slow, the traffic goes below 10Mb/s and the proxy server becomes unusable. Any hints of what may be happening? I'm using: linux-2.6.30.10 iptables-1.4.3.2 squid-3.1.1 compiled with these options: ./configure --prefix=/usr --mandir=/usr/share/man --infodir=/usr/share/info --datadir=/usr/share --localstatedir=/var/lib --sysconfdir=/etc/squid --libexecdir=/usr/libexec/squid --localstatedir=/var --datadir=/usr/share/squid --enable-removal-policies=lru,heap --enable-icmp --disable-ident-lookups --enable-cache-digests --enable-delay-pools --enable-arp-acl --with-pthreads --with-large-files --enable-htcp --enable-carp --enable-follow-x-forwarded-for --enable-snmp --enable-ssl --enable-async-io=32 --enable-linux-netfilter --enable-epoll --disable-poll --with-maxfd=16384 --enable-err-languages=Spanish --enable-default-err-language=Spanish My squid.conf: cache_mem 100 MB memory_pools off acl manager proto cache_object acl localhost src 127.0.0.1/32 acl localhost src ::1/128 acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 acl to_localhost dst ::1/128 acl localnet src 10.0.0.0/8 # RFC1918 possible internal network acl localnet src 172.16.0.0/12 # RFC1918 possible internal network acl localnet src 192.168.0.0/16 # RFC1918 possible internal network acl localnet src fc00::/7 # RFC 4193 local private network range acl localnet src fe80::/10 # RFC 4291 link-local (directly plugged) machines acl net-g1 src xxx.xxx.xxx.xxx/24 acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl CONNECT method CONNECT http_access allow manager localhost http_access deny manager http_access deny !Safe_ports http_access deny CONNECT !SSL_ports http_access allow net-g1 from where browsing should be allowed http_access allow localnet http_access allow localhost http_access deny all http_port 3128 http_port 3129 tproxy hierarchy_stoplist cgi-bin ? cache_dir ufs /var/spool/squid 8000 16 256 access_log none cache_log /var/log/squid/cache.log coredump_dir /var/spool/squid refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern . I have this issue when the cache is full, but do not really know if it is because of that. Thanks in advance and sorry my english. roberto

  Read the article

• Indirect Postfix bounces create new user directories

  - by hheimbuerger

  I'm running Postfix on my personal server in a data centre. I am not a professional mail hoster and not a Postfix expert, it is just used for a few domains served from that server. IIRC, I mostly followed this howto when setting up Postfix. Mails addressed to one of the domains the server manages are delivered locally (/srv/mail) to be fetched with Dovecot. Mails to other domains require usage of SMTPS. The mailbox configuration is stored in MySQL. The problem I have is that I suddenly found new mailboxes being created on the disk. Let's say I have the domain 'example.com'. Then I would have lots of new directories, e.g. /srv/mail/example.com/abenaackart /srv/mail/example.com/abenaacton etc. There are no entries for these addresses in my database, neither as a mailbox nor as an alias. It's clearly spam from auto-generated names. Most of them start with 'a', a few with 'b' and a couple of random ones with other letters. At first I was afraid of an attack, but all security restrictions seem to work. If I try to send mail to these addresses, I get an "Recipient address rejected: User unknown in virtual mailbox table" during the 'RCPT TO' stage. So I looked into the mails stored in these mailboxes. Turns out that all of them are bounces. It seems like all of them were sent from a randomly generated name to an alias that really exists on my system, but pointed to an invalid destination address on another host. So Postfix accepted it, then tried to redirect it to another mail server, which rejected it. This bounced back to my Postfix server, which now took the bounce and stored it locally -- because it seemed to be originating from one of the addresses it manages. Example: My Postfix server handles the example.com domain. [email protected] is configured to redirect to [email protected]. [email protected] has since been deleted from the Hotmail servers. Spammer sends mail with FROM:[email protected] and TO:[email protected]. My Postfix server accepts the mail and tries to hand it off to hotmail.com. hotmail.com sends a bounce back. My Postfix server accepts the bounce and delivers it to /srv/mail/example.com/bob. The last step is what I don't want. I'm not quite sure what it should do instead, but creating hundreds of new mailboxes on my disk is not what I want... Any ideas how to get rid of this behaviour? I'll happily post parts of my configuration, but I'm not really sure where to start debugging the problem at this point.

  Read the article

• Django rewrites URL as IP address in browser - why?

  - by Mitch

  I am using django, nginx and apache. When I access my site with a URL (e.g., http://www.foo.com/) what appears in my browser address is the IP address with admin appended (e.g., http://123.45.67.890/admin/). When I access the site by IP, it is redirected as expected by django's urls.py (e.g., http://123.45.67.890/ - http://123.45.67.890/accounts/login/?next=/) I would like to have the name URL act the same way as the IP. That is, if the URL goes to a new view, the host in the browser address should remain the same and not change to the IP address. Where should I be looking to fix this? My files: ; cpa.com (apache) NameVirtualHost *:8080 <VirtualHost *:8080> AddOutputFilterByType DEFLATE text/html text/plain text/xml text/css text/javascript application/javascript application/x-javascript BrowserMatch ^Mozilla/4 gzip-only-text/html BrowserMatch ^Mozilla/4\.0[678] no-gzip BrowserMatch \bMSIE !no-gzip !gzip-only-text/htm DocumentRoot /path/to/root ServerName www.foo.com <IfModule mod_rpaf.c> RPAFenable On RPAFsethostname On RPAFproxy_ips 127.0.0.1 </IfModule> <Directory /public/static> AllowOverride None AddHandler mod_python .py PythonHandler mod_python.publisher </Directory> Alias / /dj <Location /> SetHandler python-program PythonPath "['/usr/lib/python2.5/site-packages/django', '/usr/lib/python2.5/site-packages/django/forms'] + sys.path" PythonHandler django.core.handlers.modpython SetEnv DJANGO_SETTINGS_MODULE dj.settings PythonDebug On </Location> </VirtualHost> ; ; ports.conf (apache) Listen 127.0.0.1:8080 ; ; cpa.conf (nginx) server { listen 80; server_name www.foo.com; location /static { root /var/public; index index.html; } location /cpa/js { root /var/public/js; } location /cpa/css { root /var/public/css; } location /djmedia { alias "/usr/lib/python2.5/site-packages/django/contrib/admin/media/"; } location / { include /etc/nginx/proxy.conf; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://127.0.0.1:8080; } } ; ; proxy.conf (nginx) proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 500; proxy_buffers 32 4k;

  Read the article

• BAD DC transfering FSMO Roles to ADC

  - by Suleman

  I have a DC (FQDN:server.icmcpk.local) and an ADC (FQDN:file-server.icmcpk.local). Recently my DC is facing a bad sector problem so I changed the Operation Masters to file-server for all five roles. but when ever i turn off the OLD DC the file-server also stops wroking with AD and GPMC further i m also unable to join any other computer to this domain. For Test purpose i also added a new ADC (FQDN:wds-server.icmcpk.local) but no succes with the old DC off i had to turn the old DC on and then joined it. I m attaching the Dcdiags for all three servers. Kindly help me so that i b able to reinstall new HDD and it can go online again. --------------------------------------- Server --------------------------------------- C:\Program Files\Support Tools>dcdiag Domain Controller Diagnosis Performing initial setup: Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\SERVER Starting test: Connectivity ......................... SERVER passed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\SERVER Starting test: Replications [Replications Check,SERVER] A recent replication attempt failed: From FILE-SERVER to SERVER Naming Context: DC=ForestDnsZones,DC=icmcpk,DC=local The replication generated an error (1908): Could not find the domain controller for this domain. The failure occurred at 2012-05-04 14:07:13. The last success occurred at 2012-05-04 13:48:39. 1 failures have occurred since the last success. Kerberos Error. A KDC was not found to authenticate the call. Check that sufficient domain controllers are available. [Replications Check,SERVER] A recent replication attempt failed: From WDS-SERVER to SERVER Naming Context: DC=ForestDnsZones,DC=icmcpk,DC=local The replication generated an error (1908): Could not find the domain controller for this domain. The failure occurred at 2012-05-04 14:07:13. The last success occurred at 2012-05-04 13:48:39. 1 failures have occurred since the last success. Kerberos Error. A KDC was not found to authenticate the call. Check that sufficient domain controllers are available. [Replications Check,SERVER] A recent replication attempt failed: From FILE-SERVER to SERVER Naming Context: DC=DomainDnsZones,DC=icmcpk,DC=local The replication generated an error (1908): Could not find the domain controller for this domain. The failure occurred at 2012-05-04 14:07:13. The last success occurred at 2012-05-04 13:48:39. 1 failures have occurred since the last success. Kerberos Error. A KDC was not found to authenticate the call. Check that sufficient domain controllers are available. [Replications Check,SERVER] A recent replication attempt failed: From WDS-SERVER to SERVER Naming Context: DC=DomainDnsZones,DC=icmcpk,DC=local The replication generated an error (1908): Could not find the domain controller for this domain. The failure occurred at 2012-05-04 14:07:13. The last success occurred at 2012-05-04 13:48:39. 1 failures have occurred since the last success. Kerberos Error. A KDC was not found to authenticate the call. Check that sufficient domain controllers are available. [Replications Check,SERVER] A recent replication attempt failed: From FILE-SERVER to SERVER Naming Context: CN=Schema,CN=Configuration,DC=icmcpk,DC=local The replication generated an error (1908): Could not find the domain controller for this domain. The failure occurred at 2012-05-04 14:07:13. The last success occurred at 2012-05-04 13:48:39. 1 failures have occurred since the last success. Kerberos Error. A KDC was not found to authenticate the call. Check that sufficient domain controllers are available. [Replications Check,SERVER] A recent replication attempt failed: From WDS-SERVER to SERVER Naming Context: CN=Schema,CN=Configuration,DC=icmcpk,DC=local The replication generated an error (1908): Could not find the domain controller for this domain. The failure occurred at 2012-05-04 14:07:13. The last success occurred at 2012-05-04 13:48:39. 1 failures have occurred since the last success. Kerberos Error. A KDC was not found to authenticate the call. Check that sufficient domain controllers are available. [Replications Check,SERVER] A recent replication attempt failed: From WDS-SERVER to SERVER Naming Context: DC=icmcpk,DC=local The replication generated an error (1908): Could not find the domain controller for this domain. The failure occurred at 2012-05-04 14:07:13. The last success occurred at 2012-05-04 13:48:39. 1 failures have occurred since the last success. Kerberos Error. A KDC was not found to authenticate the call. Check that sufficient domain controllers are available. ......................... SERVER passed test Replications Starting test: NCSecDesc ......................... SERVER passed test NCSecDesc Starting test: NetLogons ......................... SERVER passed test NetLogons Starting test: Advertising ......................... SERVER passed test Advertising Starting test: KnowsOfRoleHolders ......................... SERVER passed test KnowsOfRoleHolders Starting test: RidManager ......................... SERVER passed test RidManager Starting test: MachineAccount ......................... SERVER passed test MachineAccount Starting test: Services ......................... SERVER passed test Services Starting test: ObjectsReplicated ......................... SERVER passed test ObjectsReplicated Starting test: frssysvol ......................... SERVER passed test frssysvol Starting test: frsevent There are warning or error events within the last 24 hours after the SYSVOL has been shared. Failing SYSVOL replication problems may cause Group Policy problems. ......................... SERVER failed test frsevent Starting test: kccevent ......................... SERVER passed test kccevent Starting test: systemlog An Error Event occured. EventID: 0x80001778 Time Generated: 05/04/2012 14:05:39 Event String: The previous system shutdown at 1:26:31 PM on An Error Event occured. EventID: 0x825A0011 Time Generated: 05/04/2012 14:07:45 (Event String could not be retrieved) An Error Event occured. EventID: 0x00000457 Time Generated: 05/04/2012 14:13:40 (Event String could not be retrieved) An Error Event occured. EventID: 0x00000457 Time Generated: 05/04/2012 14:14:25 (Event String could not be retrieved) An Error Event occured. EventID: 0x00000457 Time Generated: 05/04/2012 14:14:25 (Event String could not be retrieved) An Error Event occured. EventID: 0x00000457 Time Generated: 05/04/2012 14:14:38 (Event String could not be retrieved) An Error Event occured. EventID: 0xC1010020 Time Generated: 05/04/2012 14:16:14 Event String: Dependent Assembly Microsoft.VC80.MFCLOC could An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:16:14 Event String: Resolve Partial Assembly failed for An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:16:14 Event String: Generate Activation Context failed for An Error Event occured. EventID: 0xC1010020 Time Generated: 05/04/2012 14:16:14 Event String: Dependent Assembly Microsoft.VC80.MFCLOC could An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:16:14 Event String: Resolve Partial Assembly failed for An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:16:14 Event String: Generate Activation Context failed for An Error Event occured. EventID: 0x825A0011 Time Generated: 05/04/2012 14:22:57 (Event String could not be retrieved) An Error Event occured. EventID: 0xC1010020 Time Generated: 05/04/2012 14:22:59 Event String: Dependent Assembly Microsoft.VC80.MFCLOC could An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:22:59 Event String: Resolve Partial Assembly failed for An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:22:59 Event String: Generate Activation Context failed for An Error Event occured. EventID: 0xC1010020 Time Generated: 05/04/2012 14:22:59 Event String: Dependent Assembly Microsoft.VC80.MFCLOC could An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:22:59 Event String: Resolve Partial Assembly failed for An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:22:59 Event String: Generate Activation Context failed for ......................... SERVER failed test systemlog Starting test: VerifyReferences ......................... SERVER passed test VerifyReferences Running partition tests on : ForestDnsZones Starting test: CrossRefValidation ......................... ForestDnsZones passed test CrossRefValidation Starting test: CheckSDRefDom ......................... ForestDnsZones passed test CheckSDRefDom Running partition tests on : DomainDnsZones Starting test: CrossRefValidation ......................... DomainDnsZones passed test CrossRefValidation Starting test: CheckSDRefDom ......................... DomainDnsZones passed test CheckSDRefDom Running partition tests on : Schema Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Running partition tests on : Configuration Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Running partition tests on : icmcpk Starting test: CrossRefValidation ......................... icmcpk passed test CrossRefValidation Starting test: CheckSDRefDom ......................... icmcpk passed test CheckSDRefDom Running enterprise tests on : icmcpk.local Starting test: Intersite ......................... icmcpk.local passed test Intersite Starting test: FsmoCheck ......................... icmcpk.local passed test FsmoCheck ---------------------- File-Server ---------------------- C:\Users\Administrator.ICMCPK>dcdiag Directory Server Diagnosis Performing initial setup: Trying to find home server... Home Server = FILE-SERVER * Identified AD Forest. Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\FILE-SERVER Starting test: Connectivity ......................... FILE-SERVER passed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\FILE-SERVER Starting test: Advertising Warning: DsGetDcName returned information for \\Server.icmcpk.local, when we were trying to reach FILE-SERVER. SERVER IS NOT RESPONDING or IS NOT CONSIDERED SUITABLE. ......................... FILE-SERVER failed test Advertising Starting test: FrsEvent ......................... FILE-SERVER passed test FrsEvent Starting test: DFSREvent ......................... FILE-SERVER passed test DFSREvent Starting test: SysVolCheck ......................... FILE-SERVER passed test SysVolCheck Starting test: KccEvent ......................... FILE-SERVER passed test KccEvent Starting test: KnowsOfRoleHolders ......................... FILE-SERVER passed test KnowsOfRoleHolders Starting test: MachineAccount ......................... FILE-SERVER passed test MachineAccount Starting test: NCSecDesc Error NT AUTHORITY\ENTERPRISE DOMAIN CONTROLLERS doesn't have Replicating Directory Changes In Filtered Set access rights for the naming context: DC=ForestDnsZones,DC=icmcpk,DC=local Error NT AUTHORITY\ENTERPRISE DOMAIN CONTROLLERS doesn't have Replicating Directory Changes In Filtered Set access rights for the naming context: DC=DomainDnsZones,DC=icmcpk,DC=local ......................... FILE-SERVER failed test NCSecDesc Starting test: NetLogons Unable to connect to the NETLOGON share! (\\FILE-SERVER\netlogon) [FILE-SERVER] An net use or LsaPolicy operation failed with error 67, The network name cannot be found.. ......................... FILE-SERVER failed test NetLogons Starting test: ObjectsReplicated ......................... FILE-SERVER passed test ObjectsReplicated Starting test: Replications ......................... FILE-SERVER passed test Replications Starting test: RidManager ......................... FILE-SERVER passed test RidManager Starting test: Services ......................... FILE-SERVER passed test Services Starting test: SystemLog An Error Event occurred. EventID: 0x00000469 Time Generated: 05/04/2012 14:01:10 Event String: The processing of Group Policy failed because of lack of network con nectivity to a domain controller. This may be a transient condition. A success m essage would be generated once the machine gets connected to the domain controll er and Group Policy has succesfully processed. If you do not see a success messa ge for several hours, then contact your administrator. An Warning Event occurred. EventID: 0x8000A001 Time Generated: 05/04/2012 14:07:11 Event String: The Security System could not establish a secured connection with th e server ldap/icmcpk.local/[email protected]. No authentication protocol was available. An Warning Event occurred. EventID: 0x00000BBC Time Generated: 05/04/2012 14:30:34 Event String: Windows Defender Real-Time Protection agent has detected changes. Mi crosoft recommends you analyze the software that made these changes for potentia l risks. You can use information about how these programs operate to choose whet her to allow them to run or remove them from your computer. Allow changes only if you trust the program or the software publisher. Windows Defender can't undo changes that you allow. An Warning Event occurred. EventID: 0x00000BBC Time Generated: 05/04/2012 14:30:36 Event String: Windows Defender Real-Time Protection agent has detected changes. Mi crosoft recommends you analyze the software that made these changes for potentia l risks. You can use information about how these programs operate to choose whet her to allow them to run or remove them from your computer. Allow changes only if you trust the program or the software publisher. Windows Defender can't undo changes that you allow. ......................... FILE-SERVER failed test SystemLog Starting test: VerifyReferences ......................... FILE-SERVER passed test VerifyReferences Running partition tests on : ForestDnsZones Starting test: CheckSDRefDom ......................... ForestDnsZones passed test CheckSDRefDom Starting test: CrossRefValidation ......................... ForestDnsZones passed test CrossRefValidation Running partition tests on : DomainDnsZones Starting test: CheckSDRefDom ......................... DomainDnsZones passed test CheckSDRefDom Starting test: CrossRefValidation ......................... DomainDnsZones passed test CrossRefValidation Running partition tests on : Schema Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Running partition tests on : Configuration Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Running partition tests on : icmcpk Starting test: CheckSDRefDom ......................... icmcpk passed test CheckSDRefDom Starting test: CrossRefValidation ......................... icmcpk passed test CrossRefValidation Running enterprise tests on : icmcpk.local Starting test: LocatorCheck ......................... icmcpk.local passed test LocatorCheck Starting test: Intersite ......................... icmcpk.local passed test Intersite --------------------- WDS-Server --------------------- C:\Users\Administrator.ICMCPK>dcdiag Directory Server Diagnosis Performing initial setup: Trying to find home server... Home Server = WDS-SERVER * Identified AD Forest. Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\WDS-SERVER Starting test: Connectivity ......................... WDS-SERVER passed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\WDS-SERVER Starting test: Advertising Warning: DsGetDcName returned information for \\Server.icmcpk.local, when we were trying to reach WDS-SERVER. SERVER IS NOT RESPONDING or IS NOT CONSIDERED SUITABLE. ......................... WDS-SERVER failed test Advertising Starting test: FrsEvent There are warning or error events within the last 24 hours after the SYSVOL has been shared. Failing SYSVOL replication problems may cause Group Policy problems. ......................... WDS-SERVER passed test FrsEvent Starting test: DFSREvent ......................... WDS-SERVER passed test DFSREvent Starting test: SysVolCheck ......................... WDS-SERVER passed test SysVolCheck Starting test: KccEvent ......................... WDS-SERVER passed test KccEvent Starting test: KnowsOfRoleHolders ......................... WDS-SERVER passed test KnowsOfRoleHolders Starting test: MachineAccount ......................... WDS-SERVER passed test MachineAccount Starting test: NCSecDesc Error NT AUTHORITY\ENTERPRISE DOMAIN CONTROLLERS doesn't have Replicating Directory Changes In Filtered Set access rights for the naming context: DC=ForestDnsZones,DC=icmcpk,DC=local Error NT AUTHORITY\ENTERPRISE DOMAIN CONTROLLERS doesn't have Replicating Directory Changes In Filtered Set access rights for the naming context: DC=DomainDnsZones,DC=icmcpk,DC=local ......................... WDS-SERVER failed test NCSecDesc Starting test: NetLogons Unable to connect to the NETLOGON share! (\\WDS-SERVER\netlogon) [WDS-SERVER] An net use or LsaPolicy operation failed with error 67, The network name cannot be found.. ......................... WDS-SERVER failed test NetLogons Starting test: ObjectsReplicated ......................... WDS-SERVER passed test ObjectsReplicated Starting test: Replications ......................... WDS-SERVER passed test Replications Starting test: RidManager ......................... WDS-SERVER passed test RidManager Starting test: Services ......................... WDS-SERVER passed test Services Starting test: SystemLog An Error Event occurred. EventID: 0x0000041E Time Generated: 05/04/2012 14:02:55 Event String: The processing of Group Policy failed. Windows could not obtain the name of a domain controller. This could be caused by a name resolution failure. Verify your Domain Name Sysytem (DNS) is configured and working correctly. An Error Event occurred. EventID: 0x0000041E Time Generated: 05/04/2012 14:08:33 Event String: The processing of Group Policy failed. Windows could not obtain the name of a domain controller. This could be caused by a name resolution failure. Verify your Domain Name Sysytem (DNS) is configured and working correctly. ......................... WDS-SERVER failed test SystemLog Starting test: VerifyReferences ......................... WDS-SERVER passed test VerifyReferences Running partition tests on : ForestDnsZones Starting test: CheckSDRefDom ......................... ForestDnsZones passed test CheckSDRefDom Starting test: CrossRefValidation ......................... ForestDnsZones passed test CrossRefValidation Running partition tests on : DomainDnsZones Starting test: CheckSDRefDom ......................... DomainDnsZones passed test CheckSDRefDom Starting test: CrossRefValidation ......................... DomainDnsZones passed test CrossRefValidation Running partition tests on : Schema Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Running partition tests on : Configuration Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Running partition tests on : icmcpk Starting test: CheckSDRefDom ......................... icmcpk passed test CheckSDRefDom Starting test: CrossRefValidation ......................... icmcpk passed test CrossRefValidation Running enterprise tests on : icmcpk.local Starting test: LocatorCheck ......................... icmcpk.local passed test LocatorCheck Starting test: Intersite ......................... icmcpk.local passed test Intersite

  Read the article

• What is a good layout for a somewhat advanced home network and storage solution?

  - by Shaun

  My home network/storage needs are changing and I am searching for some opinions and starting points on what a good network/storage layout would be that can serve my needs for a few years into the future. I think I have a decent starting point for equipment, but I am also willing to invest fairly heavily in a solution that can last me for a while. I am a bit of a tech nerd and I have a moderate tolerance for setup of the solution. I would prefer if maintenance of the system is somewhat low once it is setup, but I am willing to accept some tradeoffs. Existing equipment: Router - Netgear WNDR3700 (gigabit) Router - DLink Gamerlounge DGL-4300 (gigabit) Switch - 16 port Trendnet green switch (gigabit) Switch - 5 port Trendnet green (gigabit) Computer - i7-950 office computer (gigabit ethernet) Computer - Q6600 quad core media center, hooked up to TV, records shows (gigabit ethernet) Computer - Acer 1810T ultraportable laptop (gigabit and N ethernet) NAS - Intel SS4200-E (gigabit) External hard drive - 2TB WD Green drive (esata) All kinds of miscellaneous network connected TV, Bluray, Verizon network extender, HDhomerun TV tuners, etc. Requirements: -Robust backup solution for a growing collection of huge family picture files and personal files, around 1.5TB. (Including offsite backup) -Central location for all user's files, while also keeping them secure from each other. -Storage for terabytes of movie backups and recorded TV, and access to them from all computers (maybe around 4TB eventually) -Possibility to host files to friends and family easily Nice to have: -Backup of terabytes of movie backups Intriguing possibilities: -Capability to have users' Windows desktops and files look the same from all network computers I am not sure if the new Windows Home Server 2011 would fit into this well, if I need a domain server, how best to organize my backups, or how to most effectively use RAID. Currently I am simply backing up all computers to a RAID 1 on the NAS box, which I was thinking could prevent a situation where I reach for a backup and find that the disk is corrupt. One possibility that I am thinking about now is simply using my media center PC with a huge RAID of hard drives on which all files are stored. Pseudo-backup of all files would be present because of the RAID, but important files would also be backed up off site via carrying hard drives to work. But what if corruption seeps into the files and the corrupted data is then backed up? Does RAID protect against this? I really want to take next to zero risks with the irreplaceable files. I can handle some degree of risk with the movies and other files. I'm looking for critiques on this idea as well as other possibilities. To summarize, my goal is high functionality, media capable, and robust backup of irreplaceable files.

  Read the article

• NTPD seems to delete all network interfaces

  - by Aurelin

  We have a couple of virtual interfaces configured on eth0 on a CentOS, and every now and then, they went down seemingly out of the blue. Now after going through the log files, I found out that apparently ntpd deletes all eth0 interfaces, and that dhclient automatically brings eth0 back up. The virtual interfaces, however, stay down which causes several of our websites to be inaccessible. Can someone explain to me why ntpd deletes interfaces? Can / should that be turned off, or can / should I configure dhclient to bring the virtual interfaces back up automatically, too? EDIT// The log files that I should've posted : Nov 12 13:10:28 raptor dhclient[20048]: DHCPREQUEST on eth0 to 255.255.255.255 port 67 (xid=0x6a825e97) Nov 12 13:10:42 raptor dhclient[20048]: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 (xid=0x24554092) Nov 12 13:10:42 raptor dhclient[20048]: DHCPOFFER from 96.126.108.78 Nov 12 13:10:42 raptor dhclient[20048]: DHCPREQUEST on eth0 to 255.255.255.255 port 67 (xid=0x24554092) Nov 12 13:10:42 raptor dhclient[20048]: DHCPACK from 96.126.108.78 (xid=0x24554092) Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #31 eth0, 50.116.50.97#123, interface stats: received=3255, sent=3256, dropped=0, active_time=1559394 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #32 eth0:0, 50.116.53.56#123, interface stats: received=3, sent=0, dropped=0, active_time=1559391 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #33 eth0:1, 66.175.211.192#123, interface stats: received=2, sent=0, dropped=0, active_time=1559389 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #34 eth0:2, 50.116.53.95#123, interface stats: received=3, sent=0, dropped=0, active_time=1559387 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #35 eth0:3, 97.107.132.32#123, interface stats: received=2, sent=0, dropped=0, active_time=1559385 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #36 eth0:4, 50.116.56.201#123, interface stats: received=2, sent=0, dropped=0, active_time=1559383 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #37 eth0:5, 66.175.212.121#123, interface stats: received=2, sent=0, dropped=0, active_time=1559381 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #38 eth0:6, 66.175.215.137#123, interface stats: received=2, sent=0, dropped=0, active_time=1559379 secs Nov 12 13:10:44 raptor NET[1573]: /sbin/dhclient-script : updated /etc/resolv.conf Nov 12 13:10:44 raptor dhclient[20048]: bound to 50.116.50.97 -- renewal in 32692 seconds. Nov 12 13:10:45 raptor ntpd[2109]: Listening on interface #39 eth0, 50.116.50.97#123 Enabled The eth0 config : DEVICE="eth0" ONBOOT="yes" BOOTPROTO="dhcp" IPV6INIT="no" IPADDR=50.116.50.97 NETMASK=255.255.255.0 GATEWAY=50.116.50.1 And the virtual interfaces (I posted the first one only, they look the same for the most part) : # Configuration for eth0:0 DEVICE=eth0:0 BOOTPROTO=none # This line ensures that the interface will be brought up during boot. ONBOOT=yes # eth0:0 IPADDR=50.116.53.56 NETMASK=255.255.255.0

  Read the article

• Apache2 & .htaccess : Apache ignoring AccessFile

  - by Elyx0

  Hi there here is my server configuration: DEBIAN 32Bits / PHP 5 / Apache Server version: Apache/2.2.3 - Server built: Mar 22 2008 09:29:10 The AccessFiles : grep -ni AccessFileName * apache2.conf:134:AccessFileName .htaccess apache2.conf:667:AccessFileName .httpdoverride All the AllowOverride statements in my apache2/ folder. mods-available/userdir.conf:6: AllowOverride Indexes AuthConfig Limit mods-available/userdir.conf:16: AllowOverride FileInfo AuthConfig Limit mods-enabled/userdir.conf:6: AllowOverride Indexes AuthConfig Limit mods-enabled/userdir.conf:16: AllowOverride FileInfo AuthConfig Limit sites-enabled/default:8: AllowOverride All sites-enabled/default:14: AllowOverride All sites-enabled/default:19: AllowOverride All sites-enabled/default:24: AllowOverride All sites-enabled/default:42: AllowOverride All The sites-enabled/default file : 1 <VirtualHost *> 2 ServerAdmin [email protected] 3 ServerName mysite.com 4 ServerAlias mysite.com 5 DocumentRoot /var/www/mysite.com/ 6 <Directory /> 7 Options FollowSymLinks 8 AllowOverride All 9 Order Deny,Allow 10 Deny from all 11 </Directory> 12 <Directory /var/www/mysite.com/> 13 Options Indexes FollowSymLinks MultiViews 14 AllowOverride All 15 Order allow,deny 16 allow from all 17 </Directory> 18 <Directory /var/www/mysite.com/test/> 19 AllowOverride All 20 </Directory> 21 22 ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ 23 <Directory "/usr/lib/cgi-bin"> 24 AllowOverride All 25 Options ExecCGI -MultiViews +SymLinksIfOwnerMatch 26 Order allow,deny 27 Allow from all 28 </Directory> 29 30 ErrorLog /var/log/apache2/error.log 31 32 # Possible values include: debug, info, notice, warn, error, crit, 33 # alert, emerg. 34 LogLevel warn 35 36 CustomLog /var/log/apache2/access.log combined 37 ServerSignature Off 38 39 Alias /doc/ "/usr/share/doc/" 40 <Directory "/usr/share/doc/"> 41 Options Indexes MultiViews FollowSymLinks 42 AllowOverride All 43 Order deny,allow 44 Deny from all 45 Allow from 127.0.0.0/255.0.0.0 ::1/128 46 </Directory> 47 48 49 50 51 52 53 54 </VirtualHost> If i change any Allow from all in Deny from all , it works whenever i put it. I've got one .htaccess at /mysite.com/.htaccess & one at /mysite.com/test/.htaccess with: Order Deny,Allow Deny from all Neither of them work i can still see my website. I've got mod_rewrite enabled but i don't think it does anything here. I've tried almost everything :/ It works on my local environnement (MAMP) but fails when on my Debian server.

  Read the article

• VMWare-Mount not recognizing virtual disks

  - by user36175

  I have two disks as .vmdk files, and four as .vdi files. I can boot virtual machines on them with Sun xMV VirtualBox, and they work just fine. However, I want to mount them on my local computer so I can read some files off of them without starting a virtual machine. I downloaded the vmware-mount utility, but I get this error, even when mounting .vmdk files, which should be VMWare images... Unable to mount the virtual disk. The disk may be in use by a virtual machine, may not have enough volumes or mounted under another drive letter. If not, verify that the file is a valid virtual disk file. Thinking it's a problem with the utility, I downloaded the SDK and made my own simple program in C to try to mount a disk. It just initializes the API, connects to it, then attempts to open the disk. I get this error, once again claiming it is not a virtual disk: **LOG: DISKLIB-DSCPTR: descriptor above max size: I64u **LOG: DISKLIB-LINK : "f:\programming\VMs\windowstrash.vdi" : failed to open (The file specified is not a virtual disk). **LOG: DISKLIB-CHAIN : "f:\programming\VMs\windowstrash.vdi" : failed to open (The file specified is not a virtual disk). **LOG: DISKLIB-LIB : Failed to open 'f:\programming\VMs\windowstrash.vdi' with flags 0x1e (The file specified is not a virtual disk). ** FAILURE ** : The file specified is not a virtual disk The files are clearly virtual disks, though, since I can actually mount and use them with a virtual machine. I tried detaching them from any VMs and trying again, but I got the same results. Any ideas? Maybe the "descriptor above max size" is a hint? Some more info: the .vmdk disks were created on other computers. I just copied them to mine and created new VMs around them, but they work fine. All the .vdi files were created on my machine. Not sure if that affects anything. Update: WinMount can mount the file.. so the problem seems to be with vmware-mount.

  Read the article

• Issues with Server 2012 using DFSR running on Hyper-V 2012

  - by Bryan

  We have a number of Server 2012 systems, all of which run virtualised on Hyper-V 2012 server. We are having problems with two such virtual instances, both of which are used as file servers, whereby they occasionally stop responding to requests to serve files to clients. After logging on to the server, attempts to shut it down gracefully fail (no error, it just fails to acknowledge a shutdown request). Recovery is a case of power cycling the server(s) from the Hyper-V console. These two servers don't server a large number of users (one serves no more than 6 users, and the other serves around 20 users), they are in the same domain, but on different physical hardware (and at different sites). They don't lock up at the same time. They both use DFSR to replicate a fairly large amount of data between themselves (200GB) over ADSL connections, this is working fine, and we have been using DFSR to do this on the previous two generations of server OS we have used (Server 2008 R2 and Server 2003 - both of which were physical installs however). Today, when one of the servers crashed, I noticed an entry in the event log, which looked similar to the following: Log Name: Application Source: ESENT Date: 27/11/2012 10:25:55 Event ID: 533 Task Category: General Level: Warning Keywords: Classic User: N/A Computer: HAL-FS-01.example.com Description: DFSRs (1500) \\.\E:\System Volume Information\DFSR\database_C8CC_101_CC00_EC0E\ dfsr.db: A request to write to the file "\\.\E:\System Volume Information\ DFSR\database_C8CC_101_CC00_EC0E\fsr.log" at offset 4423680 (0x0000000000438000) for 4096 (0x00001000) bytes has not completed for 36 second(s). This problem is likely due to faulty hardware. Please contact your hardware vendor for further assistance diagnosing the problem. When the server started up again, I went to find the event log entry to investigate further and found that the event log entry was no longer there (I assume it was in memory but failed to write to disk before the server was powered off, for the reason mentioned in the message). I found the above message by searching back further in the event log. Both of these virtual servers have their E: volumes fully allocated as opposed to dynamically expanding, and there are no other issues on any of the other virtual servers (which include server 2012, server 2008 R2 and Ubuntu 12.04 x64). There are no signs of IO, memory or CPU starvation on the host systems. I've used performance counters on the affected virtual servers to monitor memory usage (including non paged pool usage), as well as CPU and network utilisation, and none of these show any signs of trouble when the issue arises. I would have thought our configuration isn't that uncommon, so I'm wondering if anyone else has seen this, and managed to resolve the problem?

  Read the article

• Rails 3 shows 404 error instead of index.html (nginx + unicorn)

  - by Miko

  I have an index.html in public/ that should be loading by default but instead I get a 404 error when I try to access http://example.com/ The page you were looking for doesn't exist. You may have mistyped the address or the page may have moved. This has something to do with nginx and unicorn which I am using to power Rails 3 When take unicorn out of the nginx configuration file, the problem goes away and index.html loads just fine. Here is my nginx configuration file: upstream unicorn { server unix:/tmp/.sock fail_timeout=0; } server { server_name example.com; root /www/example.com/current/public; index index.html; keepalive_timeout 5; location / { try_files $uri @unicorn; } location @unicorn { proxy_pass http://unicorn; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $host; proxy_redirect off; } } My config/routes.rb is pretty much empty: Advertise::Application.routes.draw do |map| resources :users end The index.html file is located in public/index.html and it loads fine if I request it directly: http://example.com/index.html To reiterate, when I remove all references to unicorn from the nginx conf, index.html loads without any problems, I have a hard time understanding why this occurs because nginx should be trying to load that file on its own by default. -- Here is the error stack from production.log: Started GET "/" for 68.107.80.21 at 2010-08-08 12:06:29 -0700 Processing by HomeController#index as HTML Completed in 1ms ActionView::MissingTemplate (Missing template home/index with {:handlers=>[:erb, :rjs, :builder, :rhtml, :rxml, :haml], :formats=>[:html], :locale=>[:en, :en]} in view paths "/www/example.com/releases/20100808170224/app/views", "/www/example.com/releases/20100808170224/vendor/plugins/paperclip/app/views", "/www/example.com/releases/20100808170224/vendor/plugins/haml/app/views"): /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/paths.rb:14:in `find' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/lookup_context.rb:79:in `find' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/base.rb:186:in `find_template' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/render/rendering.rb:45:in `_determine_template' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/render/rendering.rb:23:in `render' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/haml-3.0.15/lib/haml/helpers/action_view_mods.rb:13:in `render_with_haml' etc... -- nginx error log for this virtualhost comes up empty: 2010/08/08 12:40:22 [info] 3118#0: *1 client 68.107.80.21 closed keepalive connection My guess is unicorn is intercepting the request to index.html before nginx gets to process it.

  Read the article

• Authenticating Apache HTTPd against multiple LDAP servers with expired accounts

  - by Brian Bassett

  We're using mod_authnz_ldap and mod_authn_alias in Apache 2.2.9 (as shipped in Debian 5.0, 2.2.9-10+lenny7) to authenticate against multiple Active Directory domains for hosting a Subversion repository. Our current configuration is: # Turn up logging LogLevel debug # Define authentication providers <AuthnProviderAlias ldap alpha> AuthLDAPBindDN "CN=Subversion,OU=Service Accounts,O=Alpha" AuthLDAPBindPassword [[REDACTED]] AuthLDAPURL ldap://dc01.alpha:3268/?sAMAccountName?sub? </AuthnProviderAlias> <AuthnProviderAlias ldap beta> AuthLDAPBindDN "CN=LDAPAuth,OU=Service Accounts,O=Beta" AuthLDAPBindPassword [[REDACTED]] AuthLDAPURL ldap://ldap.beta:3268/?sAMAccountName?sub? </AuthnProviderAlias> # Subversion Repository <Location /svn> DAV svn SVNPath /opt/svn/repo AuthName "Subversion" AuthType Basic AuthBasicProvider alpha beta AuthzLDAPAuthoritative off AuthzSVNAccessFile /opt/svn/authz require valid-user </Location> We're encountering issues with users that have accounts in both Alpha and Beta, especially when their accounts in Alpha are expired (but still present; company policy is that the accounts live on for at a minimum of 1 year). For example, when the user x (which has en expired account in Alpha, and a valid account in Beta), the Apache error log reports the following: [Tue May 11 13:42:07 2010] [debug] mod_authnz_ldap.c(377): [client 10.1.1.104] [14817] auth_ldap authenticate: using URL ldap://dc01.alpha:3268/?sAMAccountName?sub? [Tue May 11 13:42:08 2010] [warn] [client 10.1.1.104] [14817] auth_ldap authenticate: user x authentication failed; URI /svn/ [ldap_simple_bind_s() to check user credentials failed][Invalid credentials] [Tue May 11 13:42:08 2010] [error] [client 10.1.1.104] user x: authentication failure for "/svn/": Password Mismatch [Tue May 11 13:42:08 2010] [debug] mod_deflate.c(615): [client 10.1.1.104] Zlib: Compressed 527 to 359 : URL /svn/ Attempting to authenticate as a non-existant user (nobodycool) results in the correct behavior of querying both LDAP servers: [Tue May 11 13:42:40 2010] [debug] mod_authnz_ldap.c(377): [client 10.1.1.104] [14815] auth_ldap authenticate: using URL ldap://dc01.alpha:3268/?sAMAccountName?sub? [Tue May 11 13:42:40 2010] [warn] [client 10.1.1.104] [14815] auth_ldap authenticate: user nobodycool authentication failed; URI /svn/ [User not found][No such object] [Tue May 11 13:42:40 2010] [debug] mod_authnz_ldap.c(377): [client 10.1.1.104] [14815] auth_ldap authenticate: using URL ldap://ldap.beta:3268/?sAMAccountName?sub? [Tue May 11 13:42:44 2010] [warn] [client 10.1.1.104] [14815] auth_ldap authenticate: user nobodycool authentication failed; URI /svn/ [User not found][No such object] [Tue May 11 13:42:44 2010] [error] [client 10.1.1.104] user nobodycool not found: /svn/ [Tue May 11 13:42:44 2010] [debug] mod_deflate.c(615): [client 10.1.1.104] Zlib: Compressed 527 to 359 : URL /svn/ How do I configure Apache to correctly query Beta if it encounters an expired account in Alpha?

  Read the article

• iPhone 3G refuses to transfer purchased apps to iTunes

  - by andynormancx

  My iPhone 3G refuses to transfer purchased apps to iTunes. This is causing me major problems with syncing. Whenever I attempt to transfer apps from the iPhone to iTunes it goes through the motions, but never actually transfers anything. It displays the various apps in the info area at the top of the screen, but the progress bar never advances. In comparison when I sync other iPhones, using the same install of iTunes, the progress bar advances and apps are transferred. The same also happens on clean installs of iTunes on other computers, it seems to be my iPhone that is the common factor. I have tried restoring the phone from a backup, which makes no difference. This started happening months ago and the phone has since been upgraded to 3.0 and 3.1, but the problem still persists. Originally it was just a minor irritation, but I made and attempt to fix it which has made things worse. I deleted all the apps from with iTunes and then did "Transfer purchases" in the hope that it might fix something. It didn't fix anything. Also, I cannot now sync at all. If I do sync iTunes now does "transferring purchases", fails to transfer and then deletes all the apps (and data) from my iPhone. It also means I can't sync music, podcasts or anything else. I can't sync anything else, because I can't temporarily turn off app syncing because then iTunes warns that the apps on the iPhone will be deleted. I also tried de-authorising and re-authorising. What can I do to get app syncing working again ? P.S. I have considered deleting all the apps and reinstalling them one by one, in the hope that it will fix the problem. However I don't really want to embark on doing that for 55+ apps and re-entering login details etc for the apps that need them, especially as I might then find out it didn't solve the problem. Update: The latest update to iTunes 9 has improved things in one key aspect. If I let a sync run to completion iTunes no longer deletes all the apps from my phone. So I can now sync all my other data, even if I still can't sync my apps. Resolved: See my answer to the question for how I finally resolved the problem.

  Read the article

• HP DAT72x6 autoloader

  - by ericmayo

  Hoping someone here has seen this similar issue and can offer soem advise... I have an HP DAT72x6 auto loader tape backup unit. The external kind, here is a link to an owner's manual I found of it. http://www.dectrader.com/docs/set2/emr_na-c00070400-1.pdf I purchased the unit used about 6 months ago. The unit stopped working after 3-4 back-ups, it's used one day a month to do a monthly backup of another system. Suffice it to say the unit gets very little usage. There is an amber light on the front of the unit called the OAR (Operator Attention Required). The manual states to call for service when this light comes on and stays on. I've tried a few things to resolve but none are working. I've tried power cycling, re-securing the SCSI cables at both ends. Unit was used so I didn't pay much ($500) and so I don't want to spend a lot to have it fixed; might as well buy something new one if fixing this is going to cost more than $100-$150 bucks. I'm curious to see if anyone here has been around these devices or possibly is an HP repair person that can give me some things to try to resolve. The manual states that a solid amber OAR light indicates a hardware failure. When I power cycle the unit I see one of two scenarios so far. The unit powers up, shows self test in the LCD, then LCD changes to show all possible images and the OAR light comes on. The unit powers up, LCD is completely blank, the green lights go through some sort of process of going on and off and later the amber OAR light comes on and stays on. If it's a simple misalignment issue, I may be able to fix myself but not knowing what could cause the OAR light to come on gives me no where to even start. Google around gave no help either. I hoping someone here has experience with this and can help or point me in the right direction. Also, I don't have the HP Diagnostic tools mentioned in many manuals. The unit is connected to a Linux box. The 3-4 backups I've done with it so far have had no issues. We run amanda backup. Before this incident the unit was backing up and reading tapes fine. Thanks for any help or suggestions.

  Read the article

• HT Link Sync Error after Ubuntu 10.04 LTS Installation

  - by marklab

  Update 1 I just assembled an exact replica of this server, and successfully installed Ubuntu 10.04 LTS in a RAID10 configuration. The success was confirmed by a login to the initial account. There must be a hardware component that is faulty. Since the error mentions HT, which I believe to be Hyper Threading, I will start with the CPUs. Please indicate if this error is more strongly associated with any other piece of hardware. Or make a recommendation of another approach that would be good for this issue. Issue I was attempting to install Ubuntu 10.04 LTS on this system with the board RAID10 configured. However, the installation failed at the partitioning stage by rebooting the system. Upon reboot, there is an error report after POST listing the following: Node0: NB WatchDog Timer Error Node1: HT Link Sync Error Node2: HT Link Sync Error ... Node7: HT Link Sync Error Press F1 to continue/resume. After pressing F1 the system will boot from the Ubuntu 10.04 LTS installation disc. However, it will fail at the same stage, and go through the same process from there. Hardware CPU: AMD OPTERON X12 6172 G34 2.1G 18MB Motherboard: Supermicro H8QG6-F HDD: WD Caviar Green 2TB 5.4K RPM Troubleshooting I disabled RAID10 on the system, and installed the Ubuntu on a single drive. It installed successfully. I then went back to a RAID10 setup and attempted to install on the system again, and was able to make it through the partitioning stage. However, upon reboot, the system reported: Error: file not found, and then booted me into the Grub Rescue console. I feel I have aggravated the problem at this point because when I attempted to install from the boot disc again, the system reboots upon hitting enter to even start the installation process. It does the same thing when trying to boot from an Ubuntu 11 disc. I have not been able to find any information on this HT Link Sync Error, which I feel may have started the problems I am experiencing now with the installation of the OS. I am also aware that Ubuntu is said not to be supported by the motherboard according to Supermicro's site. However, since I was able to install it successfully on a single drive, I do not believe it is incompatible. I would like to know a reason for why it's failing to install on/off.

  Read the article

• In search of a network file system with extended caching to speed up file access

  - by Brecht Machiels

  I'm running a small home server that stores my documents. The disks in this server are in a RAID 1 configuration (using Linux md) and it's also periodically being backup up to an external hard drive to make sure I don't lose them. However, I'm always accessing the files from other computers on the home network using an SMB share, and this results in a considerable speed penalty (especially when connected over WLAN). This is quite annoying when editing large files, such as digital camera RAWs, for example. I've been looking for a solution to this problem. It would have to offer some kind of local caching to speed up the file access. The client would preferably not keep a copy of all data on the server, as it consists of a very large collection of photographs, most of which I will not access frequently. Instead, it should only cache the accessed files and sync the changes back in the background. Ideally, it would also do some smart read-ahead (cache the files that are in the same directory as the currently opened file, for examples), but I suppose that's asking a bit much. Synchronization should be automatic (on file change). Conflicting file changes (at the same time on different clients) are unlikely to happen in my use case, but I would prefer if they are handled properly (notification to the user). I've come across the following options, so far: something similar to Dropbox. iFolder seems to be the only thing that comes close, but its reputation (stability) and requirements put me off. A distributed file system such as OpenAFS. I'm not sure this will speed up file access. It is probably overkill for what I need. Maybe NFS or even Samba offer these possibilities. I read a bit about Windows' Offline Files, but its operation seems limited (at least on Windows XP). As this is just for personal use, I'm not willing to spend a lot of money. A free solution would be preferred. Also, the server needs to run on Linux, and I need a client for at least Windows.

  Read the article

• Using an SSD with no AHCI [ICH7 base] - Windows 7 hangs frequently

  - by h4xnoodle

  I have a Shuttle Intel G31 + ICH7 (base -- not M/R etc) system. I just bought an OCZ Vertex 3 120gb [VTX3-25SAT3-120G] which includes the Sandforce 2218 firmware. The ICH7 does not support AHCI. I understand that this can be a problem. What I don't understand, is if it's necessary to have the proper performance of this drive. I know that without AHCI I may get a limited read/write speed -- this is fine. What my concern is, is the constant freezing/hangs I'm getting with Windows 7 on any disk activity. The 'Highest Active Time' flip-flops from 0 to 100% every minute or so regardless of large or small files. EDIT: The threads/processes with the highest response time is the kernel. I've been reading about other people with Shuttle SG31G2s, and they seem to be using SSDs no problem. Is this the controller's fault? The fact that I do not have AHCI enabled? It makes sense to me that if this SSD requires AHCI features that it would cause Windows to hang, but I would like to fully determine my situation before returning things/reformatting. To initially have my drive recognise the SSD at all, I had to change the BIOS option to Force Gen II instead of Auto for the SATA controller. I then installed Windows with no problem. There were no errors in the event log related to disk usage, but watching the perfmon I could see the highest active time and the processes (usually pagefile.sys being written to, or chrome/firefox caching) which was correlated to the hanging. So now what I need answered is: should I be returning this SSD and getting one with a different controller, or returning the SSD all-together as it will never work out and I will continue to get these hangs. Posts I've read: Windows 7 New SSD SATA AHCI? -- suggests to use AHCI http://forums.anandtech.com/showthread.php?t=2189868 -- Sandforce issues Windows 7 freezes with SSD -- and attached posts Why does my Windows 7 PC / SSD drive keep freezing? -- this is not the controller I have, but still a related issue. Windows 7 hangs after longer inactivity of user -- also tried messing with power settings with no luck. It was already set to 'Never' for turning off HDDs.

  Read the article

• gunicorn + django + nginx unix://socket failed (11: Resource temporarily unavailable)

  - by user1068118

  Running very high volume traffic on these servers configured with django, gunicorn, supervisor and nginx. But a lot of times I tend to see 502 errors. So I checked the nginx logs to see what error and this is what is recorded: [error] 2388#0: *208027 connect() to unix:/tmp/gunicorn-ourapp.socket failed (11: Resource temporarily unavailable) while connecting to upstream Can anyone help debug what might be causing this to happen? This is our nginx configuration: sendfile on; tcp_nopush on; tcp_nodelay off; listen 80 default_server; server_name imp.ourapp.com; access_log /mnt/ebs/nginx-log/ourapp-access.log; error_log /mnt/ebs/nginx-log/ourapp-error.log; charset utf-8; keepalive_timeout 60; client_max_body_size 8m; gzip_types text/plain text/xml text/css application/javascript application/x-javascript application/json; location / { proxy_pass http://unix:/tmp/gunicorn-ourapp.socket; proxy_pass_request_headers on; proxy_read_timeout 600s; proxy_connect_timeout 600s; proxy_redirect http://localhost/ http://imp.ourapp.com/; #proxy_set_header Host $host; #proxy_set_header X-Real-IP $remote_addr; #proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; #proxy_set_header X-Forwarded-Proto $my_scheme; #proxy_set_header X-Forwarded-Ssl $my_ssl; } We have configure Django to run in Gunicorn as a generic WSGI application. Supervisord is used to launch the gunicorn workers: home/user/virtenv/bin/python2.7 /home/user/virtenv/bin/gunicorn --config /home/user/shared/etc/gunicorn.conf.py daggr.wsgi:application This is what the gunicorn.conf.py looks like: import multiprocessing bind = 'unix:/tmp/gunicorn-ourapp.socket' workers = multiprocessing.cpu_count() * 3 + 1 timeout = 600 graceful_timeout = 40 Does anyone know where I can start digging to see what might be causing the problem? This is what my ulimit -a output looks like on the server: core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 59481 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 50000 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) 1024 virtual memory (kbytes, -v) unlimited file locks (-x) unlimited

  Read the article

• How to diagnose repeated "Starting up database '<dbname>'"

  - by Richard Slater

  I have a SQL 2008 server which is predominantly used as a development server, in the last two weeks it has been having occasional "fits", I have isolated the cause of these fits as CHECKDB being run almost continuiously, the following log information is logged to the Windows Event Log (Source: MSSQLSERVER, Category: Server): Event: 1073758961, Message: Starting up database 'DBName1'. Event: 1073758961, Message: Starting up database 'DBName2'. Event: 1073759397, Message: CHECKDB for database 'DBName1' finished without errors on 2010-07-19 20:29:26.993 (local time). This is an informational message only; no user action is required. Event: 1073759397, Message: CHECKDB for database 'DBName1' finished without errors on 2010-07-19 20:29:26.993 (local time). This is an informational message only; no user action is required. This is repeated every 1-2 seconds untill SQL Server is restarted or the offending databases are detatched. I initially thought that it was a problem with the databases so I took a backup and restored them to a SQL Express instance, all of the data is in tact, and CHECKDB runs without problem. The two databases that were causing a problem last week were not being used; so I took full backups of them and detached the databases, this resolved the problem. However at 0100 GMT this morning to other totally unrelated databases started showing the same problems. There is nothing in the event log to suggest that something happened to the server such as a restart, there are no messages about processes crashing or issues being detected with the storage controller. Speaking to the owner of the company this computer has suffered from "gremlins" in the past, however advice was taken and the motherboard was replaced and the computer rebuilt, memory and processor are the same. Stats: O/S: Windows 2008 Standard Build 6002 CPU: 2x Pentium Dual-Core E5200 @ 2.5GHz RAM: 2GB SQL: 2008 Standard 10.0.2531 Edit: someone posted then deleted a comment about AutoClose, it was turned on on the databases affected. It seems that best practice is to disable it so I have done that with the folllowing. EXECUTE sp_MSforeachdb 'IF (''?'' NOT IN (''master'', ''tempdb'', ''msdb'', ''model'')) EXECUTE (''ALTER DATABASE [?] SET AUTO_CLOSE OFF WITH NO_WAIT'')' I won't know if the problem recurs for some time so I am still open to further answers.

  Read the article

• Can't manage iPod from linux anymore

  - by kemp

  I used to be able to see and manage my iPod with different softwares: Amarok, Rhythmbox, GTKPod. The device is a nano 1st generation 4gb. Currently it mounts regularly and can be accessed from the file system, but I get this in dmesg: [ 1547.617891] scsi 11:0:0:0: Direct-Access Apple iPod 1.62 PQ: 0 ANSI: 0 [ 1547.619103] sd 11:0:0:0: Attached scsi generic sg2 type 0 [ 1547.620478] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 [ 1547.620494] sd 11:0:0:0: [sdb] 7999487 512-byte hardware sectors: (4.09 GB/3.81 GiB) [ 1547.621718] sd 11:0:0:0: [sdb] Write Protect is off [ 1547.621726] sd 11:0:0:0: [sdb] Mode Sense: 68 00 00 08 [ 1547.621732] sd 11:0:0:0: [sdb] Assuming drive cache: write through [ 1547.623591] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 [ 1547.624993] sd 11:0:0:0: [sdb] Assuming drive cache: write through [ 1547.625003] sdb: sdb1 sdb2 [ 1547.629686] sd 11:0:0:0: [sdb] Attached SCSI removable disk [ 1548.084026] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.369502] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.504358] FAT: invalid media value (0x2f) [ 1548.504363] VFS: Can't find a valid FAT filesystem on dev sdb1. [ 1548.945173] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.945179] FAT: invalid media value (0x2f) [ 1548.945182] VFS: Can't find a valid FAT filesystem on dev sdb1. [ 1610.092886] usb 2-6: USB disconnect, address 9 The only application that can access it (partially) is Rhythmbox. I say partially because I can transfer files to the iPod but can't remove or modify them. Also one transfer didn't finish and only 9 out of 16 songs were delivered to the device. All other softwares I tried (GTKPod, Amarok, Songbird) don't even detect it. What can I do to troubleshoot this? EDIT: # fdisk -l /dev/sdb Disk /dev/sdb: 4095 MB, 4095737344 bytes 241 heads, 62 sectors/track, 535 cylinders Units = cylinders of 14942 * 512 = 7650304 bytes Disk identifier: 0x20202020 Device Boot Start End Blocks Id System /dev/sdb1 1 11 80293+ 0 Empty Partition 1 has different physical/logical beginnings (non-Linux?): phys=(0, 1, 1) logical=(0, 1, 2) Partition 1 has different physical/logical endings: phys=(9, 254, 63) logical=(10, 181, 8) Partition 1 does not end on cylinder boundary. /dev/sdb2 11 536 3919415+ b W95 FAT32 Partition 2 has different physical/logical beginnings (non-Linux?): phys=(10, 0, 7) logical=(10, 181, 15) Partition 2 has different physical/logical endings: phys=(497, 240, 62) logical=(535, 88, 61) EDIT2: The "before" state is hard to tell, it was a lot of updates ago. Haven't been using my iPod for a while so I can't say when exactly it stopped working. I'm sure Amarok was still at version 1.X but can't remember when it was. My current system is debian testing fully updated. NOTE: just noticed that if I mount the device manually instead of letting nautilus automount it, I can see it again on GTKPod but still not on Banshee AND it's vanished from Rhythmbox...

  Read the article

• EC2 Filesystem / Files stored on the wrong partiton after launching new instance from AMI

  - by Philip Isaacs

  Today I set up a new EC2 Instance from and AMI I created from an older EC2 instance. When I launched the new instance I took the AMI that was on a small instance and launched with a medium instance. From what I can tell this is pretty standard stuff. But here's the stang part. According to AWS these are the differences Small Instance (Default) 1.7 GB of memory, 1 EC2 Compute Unit (1 virtual core with 1 EC2 Compute Unit), 160 GB of local instance storage, 32-bit or 64-bit platform Medium Instance 3.75 GB of memory, 2 EC2 Compute Units (1 virtual core with 2 EC2 Compute Units each), 410 GB of local instance storage, 32-bit or 64-bit platform Okay now here's where I'm having an issue. I when I log into the new bigger instance it still reports only having 1.7 GB of ram. The other strange part is that all my old partitions are still their in the same configurations. I see a new larger partition /mnt which is essential empty. Filesystem Size Used Avail Use% Mounted on /dev/sda1 7.9G 5.9G 1.6G 79% / none 846M 120K 846M 1% /dev none 879M 0 879M 0% /dev/shm none 879M 76K 878M 1% /var/run none 879M 0 879M 0% /var/lock none 879M 0 879M 0% /lib/init/rw /dev/sda2 335G 195M 318G 1% /mnt /dev/sdf 16G 9.9G 5.1G 67% /var2 This EC2 is a web server and I was serving files off the /var2 directory but for some reason the instance is storing everything on / Okay here's what I'd like to do. Move all my website files to /mnt and have the web server point to that. Any suggestions? If it helps here is what my fstab looks like as well. root@myserver:/var# mount -l /dev/sda1 on / type ext3 (rw) [cloudimg-rootfs] proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) /dev/sda2 on /mnt type ext3 (rw) /dev/sdf on /var2 type ext4 (rw,noatime) I hope this question makes sense. Basically i want my old files on this new partition. Thanks in advance

  Read the article

• OCZ Vertex 2 not recognized by Ubuntu installer

  - by Zsub

  As I boot into the Ubuntu 10.10 (or 11.04, doesn't matter) live environment or installer, it just refuses to recognise my Vertex 2. It reports the disk as ATA and not supporting smart, shows no serial number, and doesn't list the size correctly. All fdisk tells me is Unable to read /dev/sda (it's the only storage in the PC). I'm now running a temporary install of Windows 7 off of it, which worked like a charm, so where am I going wrong with Ubuntu... Specs: Asus M4N68T-M LE V2 (BIOS 0702, most recent) OCZ Vertex 2 SSD 60 GB Amd Athlon II X4 640 Patriot PSD34G13332 4GB DDR3 ram (two banks) EDIT I installed a second drive, installed Ubuntu on that and booted, it recognised the SSD just fine. I'm now trying to apt-get upgrade the live-environment. I wonder if there is any way to sort of install Ubuntu from Ubuntu (I boot into the working install on the other drive, install it on the SSD and then boot from the SSD). EDIT2 Ok, so that doesn't work. The install detects the SSD, however, it cannot format it. EDIT3 After a fresh boot I can read out SMART-data and even perform a read-benchmark, but if I try to format it, or do a write-bench, it'll crap out and after that it says SMART is not supported. So basically it seems I can't write to the disk, as it will stop working when I do, I will try to run repeated read-benchmarks to see if that has any effect. EDIT4 I'm running several read benchmarks on the drive right now, they give results that are to be expected from an SSD. If the read-benches don't fail, I can use fdisk on the disk, but it is now stuck trying to re-read the partition table after issueing the 'w' command. EDIT5 Parted Magic did recognize the drive and with hdparm -I even could tell me the drive was in a frozen state. I powercycled it (just pull out the plug from the SSD and plug it back in) and it wasn't frozen anymore. After that I could upgrade the firmware on the drive (still using Parted Magic) and format it to Ext4. After I rebooted into the Ubuntu installer, it wouldn't get recognized and hdparm didn't want to talk to it saying HDIO_DRIVE_CMD(identify) failed: Invalid exchange. EDIT6 For some reason if I enable one of the RAID controllers (the one the SSD is connected to, obviously) Ubuntu will let me format it, mount it and write to it. The installer also recognizes it. However if the raid controller is enabled but no array is defined the motherboard can't boot from it :(

  Read the article

• apache mod_cache in v2.2 - enable cache based on url

  - by Janning

  We are using apache2.2 as a front-end server with application servers as reverse proxies behind apache. We are using mod_cache for some images and enabled it like this: <IfModule mod_disk_cache.c> CacheEnable disk / CacheRoot /var/cache/apache2/mod_disk_cache CacheIgnoreCacheControl On CacheMaxFileSize 2500000 CacheIgnoreURLSessionIdentifiers jsessionid CacheIgnoreHeaders Set-Cookie </IfModule> The image urls vary completely and have no common start pattern, but they all end in ".png". Thats why we used the root in CacheEnable / If not served from the cache, the request is forwarded to an application server via reverse proxy. So far so good, cache is working fine. But I really only need to cache all image request ending in ".png". My above configuration still works as my application server send an appropriate Cache-Control: no-cache header on the way back to apache. So most pages send a no-cache header back and they get not cached at all. My ".png" responses doesn't send a Cache-Control header so apache is only going to cache all urls with ".png". Fine. But when a new request enters apache, apache does not know that only .png requests should be considered, so every request is checking a file on disk (recorded with strace -e trace=file -p pid): [pid 19063] open("/var/cache/apache2/mod_disk_cache/zK/q8/Kd/g6OIv@woJRC_ba_A.header", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) I don't want to have apache going to disk every request, as the majority of requests are not cached at all. And we have up to 10.000 request/s at peak time. Sometimes our read IO wait spikes. It is not getting really slow, but we try to tweak it for better performance. In apache 2.4 you can say: <LocationMatch .png$> CacheEnable disk </LocationMatch> This is not possible in 2.2 and as I see no backports for debian I am not going to upgrade. So I tried to tweak apache2.2 to follow my rules: <IfModule mod_disk_cache.c> SetEnvIf Request_URI "\.png$" image RequestHeader unset Cache-Control RequestHeader append Cache-Control no-cache env=!image CacheEnable disk / CacheRoot /var/cache/apache2/mod_disk_cache #CacheIgnoreCacheControl on CacheMaxFileSize 2500000 CacheIgnoreURLSessionIdentifiers jsessionid CacheIgnoreHeaders Set-Cookie </IfModule> The idea is to let apache decide to serve request from cache based on Cache-control header (CacheIgnoreCacheControl default to off). And before simply set a RequestHeader based on the request. If it is not an image request, set a Cache-control header, so it should bypass the cache at all. This does not work, I guess because of late processing of RequestHeader directive, see https://httpd.apache.org/docs/2.2/mod/mod_headers.html#early I can't add early processing as "early" keyword can't be used together with a conditional "env=!image" I can't change the url requesting the images and I know there are of course other solutions. But I am only interested in configuring apache2.2 to reach my goal. Does anybody has an idea how to achieve my goal?

  Read the article

< Previous Page | 578 579 580 581 582 583 584 585 586 587 588 589  | Next Page >