Search Results

Search found 27248 results on 1090 pages for 'table adapter'.

Page 582/1090 | < Previous Page | 578 579 580 581 582 583 584 585 586 587 588 589  | Next Page >

• Setting up wifi router as a switch for Internet Connection Sharing

  - by William C

  Can my laptop with a 3G connection share its Internet via a Wifi router (Dlink DIR-615)? I turned Internet Connection Sharing on and Windows assigned 192.168.137.1 to my laptop's LAN adapter. Do I connect my laptop to the WAN port or to the LAN port of the router? What should I set as my router's IP address? Do I turn DHCP on my router on? Do I assign 192.168.137.x as static addresses on the other computers? If not, what? Is there anything else I need to set on my router? Thank you!

  Read the article

• Windows 7 PPTP VPN problem

  - by Marco Martins

  Hi, I'm currently using an win 7 as an network server at my home. I've created some shared folders wich can be accessed easily from any pc on my network (win and mac computers) recently I decided to turn on the win 7 pptp to access remotely to my server from anywhere. the problem is with that on, on my router my server ip change, acording to my ipconfig on the cmd my router gets the ip from a "PPP adapter RAS (dial in)". when that happens I cannot access to the shared files over the lan on my mac, but i can connect to the vpn but again can't access to my files. (i've tried connecting to the vpn from another network and it worked, even the file share) anyone can help me? thanks

  Read the article

• Laptop's wifi router is not emitting signals therefore my PC and Nokia cell are not connecting to internet

  - by umer sanny

  I have a USB internet connection which I plugged into my laptop. I converted my laptop's Wifi into a Wifi router so that I can attach my PC and cell to this network and enjoy internet, but it doesn't work. I have a Dell Inspiron N5110 i7 Windows 7 64-bit laptop, Dell D865 PC and Nokia C5. My PC and cell are showing that there is a new Wifi connection available, but when I connect to it, it won't load any web page. Reason is my laptop's Wifi is not emitting any internet signals or may be some other issue which i dont know.. laptop's adapter is 802.11b/g/n I don't know why. How can I enjoy Wifi internet on laptop, PC and cell at the same time?

  Read the article

• Areca 1880ix RAID hangs

  - by Dave

  Areca RAID controller ARC-1880ix-12 (firmware 1.50) hangs when on high load. My setup is: Chenbro 3U chassis Intel S5500BC mainboard Xeon 5603 CPU 16GB of RAM 12 Seagate SAS drives ST32000645SS (2 of them as hot spare, 10 as RAID10) Mellanox Infiniband HBA card This server is working as external infiniband storage for Xen VMs. When load is quite big Areca's firmware hangs - it becomes unreachable even from Areca's ethernet adapter. After resetting the server power it returns to normal operation. While Areca is hanged I can confirm that it is powered (ethernet link is active) and Infiniband HBA works Ok. Thanks in advance for any idea or suggestion where the problem might be!

  Read the article

• Where to find Linux drivers for my notebook

  - by smwikipedia

  Perhaps it is not proper to post on this forum. Sorry for any inconvenience. I have finally make up my mind to use Linux (Ubuntu 10.04) as the SOLE operating system on my notebook. The last obstacle is that where to find proper drivers for my devices? Such as: ATI Xpress 200M Video Adapter Texas Instrument SD Card Reader And many more... Could someone give me some advices on where to find these drivers? Many thanks.

  Read the article

• Wrong screen resolution with HDMI output to HDTV

  - by bruno077

  I own an HDTV with a native resolution of 1360x768. Sometimes I plug in my laptop to watch movies, and I used to do it with a VGA cable. I've had no problem setting the laptop to the TV native resolution with the VGA cable (1360x768). Having acquired an HDMI cable recently, I can't go past 1280x720, and if I do, the TV displays "invalid format". At 1280x720, the image is viewable but not centered, so for example I can't see the windows taskbar or titlebars. I've tried both cables (VGA and HDMI) with the same settings: Laptop's display turned off and trying to set the Tv's native resolution. What could I try to fix this issue? Could it be a faulty cable? (I'm using a Thinkpad with Windows 7) EDIT: My graphics adapter appears listed as Mobile Intel(R) 4 Series Express Chipset Family (Searching for my laptop's model yields Intel GMA 4500MHD as the graphic card) I'm downloading a driver update from Intel's website. I'll report my progress when I check its behavior tomorrow.

  Read the article

• Linux port-based routing using iptables/ip route

  - by user42055

  I have the following setup: 192.168.0.4 192.168.0.6 192.168.0.1 +-----------+ +---------+ +----------+ |WORKSTATION|------| LINUX |------| GATEWAY | +-----------+ +---------+ +----------+ 192.168.150.10 | 192.168.150.9 +---------+ | VPN | +---------+ 192.168.150.1 WORKSTATION has a default route of 192.168.0.6 LINUX has a default route of 192.168.0.1 I am trying to use the gateway as the default route, but route port 80 traffic via the VPN. Based on what I read at http://www.linuxhorizon.ro/iproute2.html I have tried this: echo "1 VPN" >> /etc/iproute2/rt_tables sysctl net.ipv4.conf.eth0.rp_filter = 0 sysctl net.ipv4.conf.tun0.rp_filter = 0 sysctl net.ipv4.conf.all.rp_filter = 0 iptables -A PREROUTING -t mangle -i eth0 -p tcp --dport 80 -j MARK --set-mark 0x1 ip route add default via 192.168.150.9 dev tun0 table VPN ip rule add from all fwmark 0x1 table VPN When I run "tcpdump -i eth0 port 80" on LINUX, and open a webpage on WORKSTATION, I don't see the traffic go through LINUX at all. When I run a ping from WORKSTATION, I get this back from some packets: 92 bytes from 192.168.0.6: Redirect Host(New addr: 192.168.0.1) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 de91 0 0000 3f 01 4ed3 192.168.0.4 139.134.2.18 Is this why my routing is not working ? Do I need to put GATEWAY and LINUX on different subnets to prevent WORKSTATION being redirected to GATEWAY ? Do I need to use NAT at all, or can I do this with routing alone (which is what I want) ?

  Read the article

• How do I configure VMware View location-based printing to use Active Directory Groups?

  - by Jason Pearce

  I am attempting to configure VMware View 4.5's Location-Based Printing, which leverages an included OEM version of ThinPrint, to assign printers to active directory groups. The location-based printing feature maps printers that are physically near client systems to VMware View desktops. I am using the Active Directory group policy setting AutoConnect Location-based Printing for VMware View, which is located in the Microsoft Group Policy Object Editor in the Software Settings folder under Computer Configuration. The AutoConnect Location-based Printing for VMware View appearst to be just a name translation table. It permits me to assign a specific printer or printers to an IP Range, Client Name, Mac Address, User, or User Group. I'm attempting to assign printers to active directory user groups. I have created a new active directory group for each printer that I intend to use in VMware View desktop pools. I will then assign active directory users to the active directory groups that represent each network printer. Example: doej is a member of the PTR-FLOOR2-NORTH-ROOM255 active directory group. Using AutoConnect, I assigned the group to receive a network printer by adding PTR-FLOOR2-NORTH-ROOM255 in the User/Group column. Problem: When doej logs in to his VDI session, the printer is not present. However, if I use a wildcard "*" in the User/Group column instead of the specific PTR-FLOOR2-NORTH-ROOM255 active directory group, the printer is present and functions as designed. Alternatives: I have tried assigning printers to active directory groups within AutoConnect in the following ways, all unsuccesfull: PTR-FLOOR2-NORTH-ROOM255 domainexample\PTR-FLOOR2-NORTH-ROOM255 domainexample.local\PTR-FLOOR2-NORTH-ROOM255 Confirmation: The information used to map the printer to the VMware View desktop is stored in a registry entry on the View desktop in HKEY_LOCAL_MACHINE\SOFTWARE\Policies\thinprint\tpautoconnect. For each of these examples, I have reviewed the registry entry and can confirm that the desktop is receiving the information from the AutoConnect translation table. Summary: Can anyone provide an example of how to configure VMware View 4.5's Location-Based Printing so that I may assign network printers to active directory groups via the included AutoConnect tool? I would welcome a clear example of a working configuration. Thank you.

  Read the article

• LAN connection suddenly domain_not_set.invalid

  - by Liam Coates

  I went to work today - internet fine as always. Came back, dreaded yellow triangle. I can connect wirelessly like i am now on my tablet. Thats completely fine. But through LAN I get the domain_not_set.Invalid message if I renew my IP for example. It seems I just don't have a DNS. But I have literally not touched anything no ones even been in the house. Hows that happen? Any help on why only wireless works would be great, I am gonna buy a wireless adapter tomorrow for the interim but I would like to know why. Thanks.

  Read the article

• My 4 GB microSD card only allows me to use 1 GB

  - by James Litewski

  My phone came with a 4 GB microSD card. On the card it lists that 3 GB goes to Muve Music which is Cricket's music program, and I get 1 GB... Well, I don't pay for Muve Music, so why waste the space? I thought I'd be able to simply buy an adapter and reformat the microSD card to get the full 4 GB; but that wasn't the case... I could only find the 1 GB partition on the card. I even tried reformatting the disk, but I had no luck. How can I get the full 4 GB? BTW, I'm running Mac OS X v10.7 (Lion).

  Read the article

• Get OS information with WMI from Small Business Server 2011 for Windows 2008 virtual machine

  - by Drew

  In my organization, the main server is Windows Small Business 2011. It uses a WMI service (I think) to get the Security and Update status of computers on the network. I have a Server 2008 virtual machine in VirtualBox with bridged network adapter. The SBS will not correctly get the status of, nor the operating system of, the Server 2008 VM. What settings do I have wrong / can I actually do this for a virtual machine in the first place? -- I do not know what further information might be needed, just ask and I will post.

  Read the article

• MySQL ADO.NET Connector & MSSQL Integration Services

  - by user1114330

  Here I am, day three... attempting to sync a data view on a Windows Vista box (64 bit) running MSSQL 2012 and Visual Studio 2010. Sanity is slipping and hunger for progress fills my attention. I went through hell trying to get the MySQL ODBC drivers to get the job but to no avail...everyone seems to be lost and all the threads I can find are solutions that do not work for me. The problem: System DSN's not being seen by SSIS. SSIS DSN Not Showing as ODBC Data Source I make the decision to try out the ADO.NET connector...and to my surprise it is actually in the selection list in data sources in SSIS. So I take off running to create a Data Flow Task, create an ADO.NET Source (a local MSSQL DB)...all is good as usual. Then I move swiftly to creating a ADO.NET Destination, enter my credentials...wow, I am selecting a database finally on my linux server! Happy thinking that I finally have figured a way to get the job done. Then I move to mappings...nope, something is wrong...I am getting an error that hurts my eyes: Pipeline component has returned HRESULT error code 0xC0208457 from a a method call. Error at Data Flow Task [ADO NET Destination [81]]: Failed to get properties of external columns. The table name you entered may not exist or you do not have SELECT permission on the table object and an alternative attempt to get column properties through connection has failed. Detailed error messages are" You have an error in your SQL syntax check the manual that corresponds to your MySQL server version for the right syntax to use near "database".tablename" at line 1. The descriptor files on path C:\Program Files (x86)\Microsoft SQL Server\110\DTS\ProviderDescriptors\ does not contain schema information for connection of type MySQL.Data.MySqlClient.MySqlConnection. So it looks like it can't the information and therefore I cannot map the tables properly. Any ideas on this would be ultra helpful...thanks in advance to All!

  Read the article

• Windows 7 RC sleep on Thinkpad R51?

  - by Ragesh

  I have an old Thinkpad R51 and Windows 7 just doesn't give me a Sleep option. I suspect it's because it's running the default VGA driver. The machine has an Intel 855 GME graphics adapter but there doesn't seem to be a WDDM driver available publicly. Lenovo's driver download page just says that drivers for Vista are bundled with the OS. Apparently, they aren't bundled with Windows 7 as it always defaults to a generic VGA driver. Is there a reliable way to get Sleep to work on this machine?

  Read the article

• How to create direct RS232 (PPP) connection from Windows 7

  - by Jonny Wright

  I'm trying to create a direct connection to a hardware device via RS232 serial connection. Am using a USB to Serial adapter and works fine in WinXP but the option seems to have disappeared in Win7. This is the only connection option available for this piece of hardware so I have no choice. Currently have a netbook with WinXP installed purely for interfacing with this hardware. In XP it was just a matter of creating an "Advanced connection" and then "Directly to another computer" etc, I can find no such options in Win7.

  Read the article

• Corrupted NTFS Drive showing multiple unallocated partitions

  - by volting

  My external hdd with a single NTFS partition was accidentaly plugged out (kids!)... and is now corrupted. Iv tried running ntfsfix - with no luck - output below.. When I look at the disk under disk management in Windows 7 it shows up as having 5 partitions 2 of which are unallocated - none have drive letters and it is not possible to set any (that option and most others are greyed out) - so I can't run chkdsk /f Iv tried using Minitool partition wizard which was mentioned as a solution to another similar question here. It showed the whole drive as one partition, but as unallocated, and the option -- "Check File System" was greyout. Is there anything else I could try ? Output of fdisk -l Disk /dev/sdb: 1500.3 GB, 1500299395072 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930272256 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytest I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x69205244 This doesn't look like a partition table Probably you selected the wrong device. Device Boot Start End Blocks Id System /dev/sdb1 ? 218129509 1920119918 850995205 72 Unknown /dev/sdb2 ? 729050177 1273024900 271987362 74 Unknown /dev/sdb3 ? 168653938 168653938 0 65 Novell Netware 386 /dev/sdb4 2692939776 2692991410 25817+ 0 Empty Partition table entries are not in disk order Output of ntfsfix me@vaio:/dev$ sudo ntfsfix /dev/sdb Mounting volume... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error FAILED Attempting to correct errors... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error FAILED Failed to startup volume: Input/output error Checking for self-located MFT segment... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument OK ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error Volume is corrupt. You should run chkdsk. Options available with MiniTool: Related questions: How to fix a damaged/corrupted NTFS filesystem/partition without losing the data on it? Repair corrupted NTFS File System

  Read the article

• Windows 7 wifi reports "no network access" and "no internet access" but connects in fedora

  - by rick2047

  I am running windows 7 home basic (64bit) on a Acer 5742G laptop with Atheos wifi adapter in it. Yesterday, I hiberneted my computer as I always do and up untill then the wifi was working fine. When I booted my computer up again today I started having a strange problem: It detects my wifi but after connecting to it, it keeps on oscillating between states of no network access and no internet access. I can't connect to anything (the internet or my router). I tried to reset my internet protocol stack using this fixit file. I also tried to uninstall and reinstall my network driver. Neither helped. I am using the same laptop's fedora installation right now and the wifi is working perfectly fine. Please help. Edit To add additional details, I have Microsoft Security essentials as my antivirus software and I haven't messed with the firewall or the router configurations.

  Read the article

• Cisco Aironet 1200 Series AP Configuration

  - by nonterrorist

  I am attempting to configure a new CISCO Aironet 1200 Series Access Point to have a fixed IP. I have been searching online and I have come to the conclusion that the default IP address of this device is 10.0.0.1. These are the steps I have taken: My machine is plugged directly into the Ethernet port (not the Console port) of the AP. My Ethernet adapter is set to 10.0.0.2. I have reset the AP by holding the Mode button while powering up the device. The issue remains that I can not access 10.0.0.1 through the web, nor can I ping that address.

  Read the article

• Messed up partitions... system will not boot!

  - by someguy

  I did a really dumb thing. cfdisk threw an error at me saying "FATAL ERROR: Bad primary partition 3: Partition ends in the final partial cylinder", so I installed Partition Table Doctor to see if I could fix the problem. When the program started up, it told me there were problems with my partitions, and asked if I wanted them fixed (cannot remember real message, but I believe it had something to do with the cylinder boundaries), so, blindly, without thinking of the consequences, I did. Now, my system will not boot. I tried booting from the Windows 7 installation CD. I went to install a fresh copy, but it said that "No drives were found". I then opened up diskpart. According to diskpart, there is only one partition, containing one volume, assigned the letter "C". Before, I had four partitions! It is also saying that the file system is RAW. Is there any way I can fix this? I have important data that I do not want to lose. Later on... I tried fdisk with the option -l, which lists the partition table(s), and this is what I got: Ignoring extra extended partition 4 Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 64 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x163df116 Device Boot Start End Blocks Id System /dev/sda1 6 18 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 18 7851 62918572+ 7 HPFS/NTFS /dev/sda3 13073 30402 139196416 f W95 Ext'd (LBA) /dev/sda3 13073 30402 139196416 f W95 Ext'd (LBA) /dev/sda3 13073 30403 139203193 7 HPFS/NTFS I don't know if this will help, but it's extra information, at least. Also, this is how I had my partitions: 40MB (Unallocated) 100MB (System Reserved) 60GB (Windows, C:) 40GB (Was reserved for secondary OS) ~132GB (Home, E:)

  Read the article

• How to make Windows 7 Network show Samba share after VM is rebooted/restored?

  - by lackey

  On Windows 7, I have VirtualBox running Linux (Ubuntu 8.04), with Samba set up so that the Windows host can access it. But if the virtual machine is shut down & restored, or rebooted, the Windows Network no longer shows it. I've tried refreshing many times, restarting Samba, disabling/enabling the virtual network adapter, and running the succession of commands ipconfig /release, ipconfig /flushdns, & ipconfig /renew, but none worked. As a last resort I could restart the host itself, but is there a better way?

  Read the article

• How to connect 2 virtual hosts running on the same machine?

  - by Gabrielle

  I have 2 virtual hosts running on my Windows XP laptop. One is Ubuntu running inside vmware player. The other is MS virtual PC (so I can test with IE6 ). The Ubuntu virtual host is running my web application with apache. I can point my browser on my laptop at the Ubuntu IP and view my web app. I read this post http://stackoverflow.com/questions/197792/how-to-connect-to-host-machine-from-within-virtual-pc-image and was able to get my Virtual PC to ping my physical machine using the loopback adapter. But I'm stuck on getting my Virtual PC to see my web application running in the Ubuntu vmware player host. I appreciate any suggestions.

  Read the article

• How to have 2 windows machines on the same network with the same IP address

  - by Stu

  I have a custom made ADC device that is spitting out data by addressed UDP packets. I have that device plugged into a 4 port switch. I have one windows embedded standard 7 machine which is the normal recipient of that data. To be able to receive the data (Using LabVIEW) the windows network adapter IPv4 settings must have a static IP address that corresponds to the UDP packet destination. I would like to add a second windows machine (This one is just regular Win 7 Pro) to simultaneously catch the data, however with all devices connected to the switch, the Win 7 Pro machine recognizes an IP address conflict and will not take the setting for the required static IP address. (The network adaptor settings show that the correct value has been entered but ipconfig shows that it is not actually set.) Neither windows machine needs to transmit network data, they only need to be able to receive the UDP data from the ADC device. Is there any way to disable this IP address conflict detection 'feature' of windows networking?

  Read the article

• Why does the CPU usage reach 100% when laptop is plugged in?

  - by Mayank

  I have an HP Elitebook 8440p with Windows 7 Ultimate, i7 Processor and 8 GB RAM. For the last couple of days, when I plug-in my laptop for charging, the CPU usage shoots up to 100% and remains there for around 15 minutes. No offending process shows up in Task Manager/Process Explorer but the laptop is practically unusable for that time. The CPU usage becomes normal when I remove the power cord but shoots up again when plugged back. This is happening with different power adapters/wall sockets so it might not be a faulty adapter issue. Why is this happening and any pointer to resolve this issue?

  Read the article

• Dell Vostro Desktop error

  - by goldenmean

  Faced a strange situation at work today. We have people sitting at a table on opposite sides, with power cables underneath the table. This morning when the person sitting opposite to me banged his feet on ground, it disturbed the power cable to my PC and it turned-off. So when I turned it on, it says, "No boot device found" Press F1 to setup or F5 to perform test... There was no physical impact/crash/fall of the desktop cabinet, which could have crashed/damaged the hard disk physically. EDIT: The OS is Windows 7 So I tried to recognize it in the Bios setup, but even there it could not find the SATA disk that is connected to this machine. So then I opened the cabinet, removed the power supply and plugged it back again. Tried to reboot, same error, "Boot device not found" It is not recognizing the hard disk. Any ideas about what might be wrong? Hard-disk crash, OS Crash(But it doesn't even go to the point of loading the disk after the initial Bios execution, so doubt this...) Any pointers about how I should proceed to troubleshoot/solve this error are welcome.

  Read the article

• How do I copy files between harddrives on Ubuntu CLI?

  - by ed209

  I have a dedicated server with a 120gb main ssd. The server happens to come with a couple of 3000GB hard drives. I'd like to use them to back up my main drive. Preferably, I'd like one as an exact copy of the main SSD and the other with incremental backups of the mysql database and a user uploads file. These are the drives I have Disk /dev/sda: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders, total 234441648 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000f2e18 Device Boot Start End Blocks Id System /dev/sda1 2048 4196352 2097152+ 83 Linux /dev/sda2 4198400 5246976 524288+ 83 Linux /dev/sda3 5249024 234441647 114596312 83 Linux Disk /dev/sdb: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders, total 5860533168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Disk /dev/sdb doesn't contain a valid partition table Disk /dev/sdc: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders, total 5860533168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Disk /dev/sdc doesn't contain a valid partition table The first problem I have, is that I have no idea how to copy from one drive to another. Kind of embarrassing I know, but I don't know where to start. I'm thinking of this in terms of Mac OS cli where I'm able to copy between /Volumes - is there an equivalent? (there is nothing under /mnt or /media)

  Read the article

• Monitor does not work past certain resolution.

  - by Steve Stifler

  I have a Macbook 5.1 with Snow Leopard, and a Samsung SyncMaster 2253BW that I use for an external monitor. I connect it to my laptop via a DVI-to-MiniDisplayPort adapter. Whenever I try to set the resolution of the monitor to 1680x1050, its maximum resolution (at least the only one that fills the entire screen), the screen flickers once or twice before claiming there is no source attached. I've had this issue since the first time I tried to connect the two, however for some reason for a brief period in time the monitor would successfully display at full resolution. All lower resolutions work fine too, it's just at 1680x1050 that the problems occur. Any ideas as to why this is happening? Thanks.

  Read the article

< Previous Page | 578 579 580 581 582 583 584 585 586 587 588 589  | Next Page >