Search Results

Search found 17366 results on 695 pages for 'memory card'.

Page 587/695 | < Previous Page | 583 584 585 586 587 588 589 590 591 592 593 594  | Next Page >

• iwlwifi on lenovo z570 disabled by hardware switch

  - by Kevin Gallagher

  It was working fine with windows 7. The hardware switch is not disabled. I've toggled it back and forth dozens of times. The wifi light never turns on and it always lists as hardware disabled. I have the latest updates installed. I've been searching for solutions, but none of them seem to work for me. I've tried removing acer-wmi. I've tried setting 11n_disable=1. I've tried resetting the bios. I've tried using rfkill to unblock (only removes soft block). I've rebooted dozens of times. The wifi light turns off as soon as grub loads. Edit: I have a usb edimax wireless nic. It shows hardware disabled as well (although rfkill lists as unblocked). If I unload iwlwifi the usb nic works fine. uname -a `Linux xxx-Ideapad-Z570 3.2.0-55-generic #85-Ubuntu SMP Wed Oct 2 12:29:27 UTC 2013 x86_64 x86_64 x86_64 GNU/Linu`x rfkill list 19: phy18: Wireless LAN Soft blocked: no Hard blocked: yes dmesg [43463.022996] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [43463.023002] Copyright(c) 2003-2011 Intel Corporation [43463.023107] iwlwifi 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [43463.023190] iwlwifi 0000:03:00.0: setting latency timer to 64 [43463.023253] iwlwifi 0000:03:00.0: pci_resource_len = 0x00002000 [43463.023257] iwlwifi 0000:03:00.0: pci_resource_base = ffffc900057c8000 [43463.023261] iwlwifi 0000:03:00.0: HW Revision ID = 0x0 [43463.023797] iwlwifi 0000:03:00.0: irq 43 for MSI/MSI-X [43463.024013] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [43463.024250] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S [43463.045496] iwlwifi 0000:03:00.0: device EEPROM VER=0x15d, CALIB=0x6 [43463.045501] iwlwifi 0000:03:00.0: Device SKU: 0X50 [43463.045504] iwlwifi 0000:03:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [43463.045542] iwlwifi 0000:03:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [43463.045744] iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio. [43463.047652] iwlwifi 0000:03:00.0: loaded firmware version 39.31.5.1 build 35138 [43463.047823] Registered led device: phy18-led [43463.047895] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [43463.048037] ieee80211 phy18: Selected rate control algorithm 'iwl-agn-rs' [43463.055533] ADDRCONF(NETDEV_UP): wlan0: link is not ready nm-tool State: connected (global) - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: unavailable Default: no HW Address: 74:E5:0B:4A:9F:C2 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points lshw -C network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:4a:9f:c2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-55-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:43 memory:f1500000-f1501fff lspci 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak]

  Read the article

• C-states and P-states : confounding factors for benchmarking

  - by Dave

  I was recently looking into a performance issue in the java.util.concurrent (JUC) fork-join pool framework related to particularly long latencies when trying to wake (unpark) threads in the pool. Eventually I tracked the issue down to the power & scaling governor and idle-state policies on x86. Briefly, P-states refer to the set of clock rates (speeds) at which a processor can run. C-states reflect the possible idle states. The deeper the C-state (higher numerical values) the less power the processor will draw, but the longer it takes the processor to respond and exit that sleep state on the next idle to non-idle transition. In some cases the latency can be worse than 100 microseconds. C0 is normal execution state, and P0 is "full speed" with higher Pn values reflecting reduced clock rates. C-states are P-states are orthogonal, although P-states only have meaning at C0. You could also think of the states as occupying a spectrum as follows : P0, P1, P2, Pn, C1, C2, ... Cn, where all the P-states are at C0. Our fork-join framework was calling unpark() to wake a thread from the pool, and that thread was being dispatched onto a processor at deep C-state, so we were observing rather impressive latencies between the time of the unpark and the time the thread actually resumed and was able to accept work. (I originally thought we were seeing situations where the wakee was preempting the waker, but that wasn't the case. I'll save that topic for a future blog entry). It's also worth pointing out that higher P-state values draw less power and there's usually some latency in ramping up the clock (P-states) in response to offered load. The issue of C-states and P-states isn't new and has been described at length elsewhere, but it may be new to Java programmers, adding a new confounding factor to benchmarking methodologies and procedures. To get stable results I'd recommend running at C0 and P0, particularly for server-side applications. As appropriate, disabling "turbo" mode may also be prudent. But it also makes sense to run with the system defaults to understand if your application exhibits any performance sensitivity to power management policies. The operating system power management sub-system typically control the P-state and C-states based on current and recent load. The scaling governor manages P-states. Operating systems often use adaptive policies that try to avoid deep C-states for some period if recent deep idle episodes proved to be very short and futile. This helps make the system more responsive under bursty or otherwise irregular load. But it also means the system is stateful and exhibits a memory effect, which can further complicate benchmarking. Forcing C0 + P0 should avoid this issue.

  Read the article

• best way to "introduce" OOP/OOD to team of experienced C++ engineers

  - by DXM

  I am looking for an efficient way, that also doesn't come off as an insult, to introduce OOP concepts to existing team members? My teammates are not new to OO languages. We've been doing C++/C# for a long time so technology itself is familiar. However, I look around and without major infusion of effort (mostly in the form of code reviews), it seems what we are producing is C code that happens to be inside classes. There's almost no use of single responsibility principle, abstractions or attempts to minimize coupling, just to name a few. I've seen classes that don't have a constructor but get memset to 0 every time they are instantiated. But every time I bring up OOP, everyone always nods and makes it seem like they know exactly what I'm talking about. Knowing the concepts is good, but we (some more than others) seem to have very hard time applying them when it comes to delivering actual work. Code reviews have been very helpful but the problem with code reviews is that they only occur after the fact so to some it seems we end up rewriting (it's mostly refactoring, but still takes lots of time) code that was just written. Also code reviews only give feedback to an individual engineer, not the entire team. I am toying with the idea of doing a presentation (or a series) and try to bring up OOP again along with some examples of existing code that could've been written better and could be refactored. I could use some really old projects that no one owns anymore so at least that part shouldn't be a sensitive issue. However, will this work? As I said most people have done C++ for a long time so my guess is that a) they'll sit there thinking why I'm telling them stuff they already know or b) they might actually take it as an insult because I'm telling them they don't know how to do the job they've been doing for years if not decades. Is there another approach which would reach broader audience than a code review would, but at the same time wouldn't feel like a punishment lecture? I'm not a fresh kid out of college who has utopian ideals of perfectly designed code and I don't expect that from anyone. The reason I'm writing this is because I just did a review of a person who actually had decent high-level design on paper. However if you picture classes: A - B - C - D, in the code B, C and D all implement almost the same public interface and B/C have one liner functions so that top-most class A is doing absolutely all the work (down to memory management, string parsing, setup negotiations...) primarily in 4 mongo methods and, for all intents and purposes, calls almost directly into D. Update: I'm a tech lead(6 months in this role) and do have full support of the group manager. We are working on a very mature product and maintenance costs are definitely letting themselves be known.

  Read the article

• Merging Social Accounts: What We Learned This Weekend

  - by Mike Stiles

  Guest Post by Erika BrookesWe learned that it’s not always as easy as you think it’s going to be. While it’s widely accepted that merging multiple owned Facebook Pages that are duplicating communities and putting out the same type of content is a best practice, actually pulling it off without rattling fans is a trickier proposition. Facebook is nice and clear about how to merge Facebook Pages. Although content is not carried over, Likes from the pages you’re merging are. So you can imagine the surprise when such fans start seeing posts in their News Feed from a page they don’t believe they ever Liked. One community member accurately likened it to having your bank come under another bank’s brand name. The Facebook Page changes to the new brand, just like your debit card, emails, signs and other communication. This weekend we did our merge. The Facebook communities of Vitrue, Involver and Collective Intellect were pulled into one community, Oracle Social. Could we have handled it better? Oh yeah. Our intent was to make sure, to the fullest extent possible, that the fans of the Vitrue, Involver, and Collective Intellect brand pages were well-informed about the pending page merges in ADVANCE of the merge. While many were aware that Oracle acquired the three companies, many were not. We learned from fan feedback that we should have sent notifications MUCH earlier to make the brand Page merge crystal clear and to answer any questions. That was our bad, our responsibility and we apologize for Oracle Social showing up in your News Feed if you were not aware that it was a result of your fandom of Vitrue, Involver or Collective Intellect. It was our job to make you aware well in advance. Some felt they had never Liked the fan Pages of Vitrue, Involver or Collective Intellect, so they were understandably upset (some cultures may call it “fit to be tied”) when they found themselves fans of Oracle Social. One thing to consider is that since 2009, brands and developers have used and enjoyed free Involver tab apps like Twitter, RSS and YouTube (1.2 million of which are currently active), which included an opt-in Liking the Involver Page. Often, when Liking happens in a manner outside of the traditional clicking of a Like button on a brand Page, it’s easy to forget a Page was indeed Liked. Lastly, a few felt that their Like of the Page had been “bought.” It was not. No fans or Likes were separately purchased. Yes, the companies and the social properties of Vitrue, Involver and Collective Intellect were acquired by Oracle. Those brands are now being coordinated into the larger Oracle brand. In social media, that means those brands are being integrated into the Oracle Social community. So what now? We apologize and apply lessons learned. We learned that you not only have to communicate thoroughly and clearly, but you have to communicate well in advance of any actionable items that will affect fans. We’re more than willing to walk straight to the woodshed when we deserve it. Going forward, the social team here is dedicated to facilitating content, discussion and sharing around social for marketers, agencies, IT stakeholders and social staffs, including community managers. We anticipate Oracle Social being the premier gathering place for true social innovators as we move into social’s exciting next phase of development. Inevitably, some will still feel they are fans of the Page in error. While we hate to see you go, you may unlike the Page if it’s not relevant or useful to you. Let’s continue to contribute, participate, foster our desire to learn, and move forward together positively and constructively - both for current fans of the community and the many fans to come.

  Read the article

• Need help identifing what resources (eg. In MIT OpenCourseWare) can help me prepare for a test [closed]

  - by jiewmeng

  I am entering uni soon. I can sit for a placement test to see if I elegible for exemptions. The details are http://www.comp.nus.edu.sg/undergraduates/TestScope11_12.html Or CS2100 Computer Organisation (please click title) The objective of this module is to familiarise students with the fundamentals of computing devices. Through this module students will understand the basics of data representation, and how the various parts of a computer work, separately and with each other. This allows students to understand the issues in computing devices, and how these issues affect the implementation of solutions. Topics covered include data representation systems, combinational and sequential circuit design techniques, assembly language, processor execution cycles, pipelining, memory hierarchy and input/output systems. Recommended Textbooks Digital Design: Principles and Practices [DDPP] by John F. Wakerly, Prentice-Hall. ISBN 0-13-324500-4. Computer Organizations and Design (The hardware/software interface) by David A. Patterson and John L. Hennessy. CS2105 Introduction to Computer Networks (please click title) This course aims to provide a broad introduction to computer networks and some appreciations of network application programming. It covers a range of topics including basic data communication and computer network concepts, protocols, networked computing concepts and principles, network applications development and network security. The emphasis of teaching is on the working principles and application of computer networks. As an integral part of the course, tutorials and practical assignments enforcing learning will also be given. These assignments provide an early exposure in network application programming and they should be able to complete by using personal computers and school's network facilities. Topics included: An overview of computer networks and the Internet Basic data communications Application layer Transport layer Network layer and routing Link layer and local area networks Recommended Textbook James F. Kurose & Keith W. Ross, Computer networking: A top-down approach featuring internet, Addison Wesley, 2001 I am wondering what resources eg. MIT OpenCourseWare or other universities resources are available to help he perpare for these particular modubles. I am thinking does the Networking one look like CCNA? The computer oragization. Its like electronics, assembly etc? I learnt some electronics in Poly but looking at the sample papers, uni looks very different... I have about 1 month to prepare if I want any chance of exempting from these modules :) any help?

  Read the article

• Certification Notes: 70-583 Designing and Developing Windows Azure Applications

  - by BuckWoody

  Last Updated: 02/01/2011 It’s time for another certification, and we’ve just release the 70-583 exam on Windows Azure. I’ve blogged my “study plans” here before on other certifications, so I thought I would do the same for this one. I’ll also need to take exam 70-513 and 70-516; but I’ll post my notes on those separately. None of these are “brain dumps” or any questions from the actual tests - just the books, links and notes I have from my studies. I’ll update these references as I’m studying, so bookmark this site and watch my Twitter and Facebook posts for when I’ll update them, or just subscribe to the RSS feed. A “Green” color on the check-block means I’ve done that part so far, red means I haven’t. First, I need to refresh my memory on some basic coding, so along with the Azure-specific information I’m reading the following general programming books: Introducing Microsoft .NET (Pro-Developer): link   Head First C#, 2E: A Learner's Guide to Real-World Programming with Visual C# and .NET: link Microsoft Visual C# 2008 Step by Step: link  c The first place to start is at the official site for the certification. link c On that page you’ll find several resources, and the first you should follow is the “Save to my learning” so you have a place to track everything. Then click the “Related Learning Plans” link and follow the videos and read the documentation in each of those bullets. There are six areas on the learning plan that you should focus on - make sure you open the learning plan to drill into the specifics. c Designing Data Storage Architecture (18%) Books I’m Reading: Links: My Notes: c Optimizing Data Access and Messaging (17%) Books I’m Reading: Links: My Notes: c Designing the Application Architecture (19%) Books I’m Reading: Applied Architecture Patterns on the Microsoft Platform: link Links: My Notes: c Preparing for Application and Service Deployment (15%) Books I’m Reading: Links: My Notes: c Investigating and Analyzing Applications (16%) Books I’m Reading: Links: My Notes: c Designing Integrated Solutions (15%) Books I’m Reading: Applied Architecture Patterns on the Microsoft Platform (2nd mention) Links: My Notes:

  Read the article

• Manic Monday - More OpenWorld Solaris Sessions: Developers, Cloud, Customer Insights, Hardware Optimization

  - by Larry Wake

  We're overflowing with Monday sessions; literally more than one person can take in. Learn more about what's new in Oracle Solaris Studio, hear about the latest x86 and SPARC hardware optimizations, get some insights on cloud deployment strategies, and find out from your peers what they're doing with Oracle Solaris. If you're an OpenWorld attendee, go to to Schedule Builder to guarantee your space in any session or lab. See yesterday's blog post and the "Focus on Oracle Solaris" guide for even more sessions. Monday, October 1st: 10:45 AM - Maximizing Your SPARC T4 Oracle Solaris Application Performance(CON6382,  Marriott Marquis - Golden Gate C3) Hear how customers and commercial software partners have reached peak performance on SPARC T4 servers and engineered systems with Oracle Solaris Studio and its latest tools for analyzing, reporting, and improving runtime performance: Autoparallelizing, high-performance compilers Performance Analyzer (used to find performance hotspots) Thread Analyzer (to expose data races and deadlocks) Code Analyzer (used to discover latent memory corruption issues) 10:45 Cloud Formation: Implementing IaaS in Practice with Oracle Solaris(CON8787, Moscone South 302) Decisions, decisions--at the same time, we've got a session that covers why Oracle Solaris is the ideal OS for public or private clouds, IaaS or PaaS, with built-in features for elastic infrastructure, unrivaled security, superfast installation and deployment, nonstop availability, and crystal-clear observability. This session will include a customer study on how Oracle Solaris is used in the cloud today to implement the Oracle stack. 12:15 PM - Customer Insight: Oracle Solaris on Oracle Exadata, Oracle Exalogic, and SPARC SuperCluster(CON8760, Moscone South 270) Hear from customers what benefits they have realized from using the Oracle stack on Oracle Exadata and Oracle’s SPARC SuperCluster and from using Oracle Solaris on those engineered systems, taking advantage of built-in lightweight OS virtualization (Zones), enterprise reliability and scale, and other key features. 1:45 PM - Case Study: Mobile Tornado Uses Oracle Technology for Better RAS and TCO?(CON4281, Moscone West 2005) Mobile Tornado develops and markets instant communication platforms, replacing traditional radio networks with cellular networks. Its critical concern is uptime. Find out how they've used Oracle Solaris, Netra SPARC T4, and Oracle Solaris Cluster, including Oracle Solaris ZFS and Zones, for their Oracle Database deployments to improve reliability and drive down cost. 3:15 PM - Technical Panel: Developing High Performance Applications on Oracle Solaris(CON7196, Marriott Marquis - Golden Gate C2) Engineers from the Oracle Solaris, Oracle Database, and Oracle Tuxedo development teams, and Oracle ISV Engineering discuss how they develop high-performance enterprise applications that take advantage of Oracle's SPARC and x86 servers, with Oracle Solaris Studio and new Oracle Solaris 11 features. Topics will include developer tools, parallel frameworks, best practices, and methodologies, as well as insights and case studies on parallelizing and optimizing application performance on Oracle Solaris. Bring your best questions! 3:15 PM -  x86 Power Management with Oracle Solaris: Current State, Opportunities, and Future(CON6271, Moscone West 2012) Another option for this time slot: learn about how Intel Xeon and Oracle Solaris work together to reduce server power consumption. This presentation addresses some of the recent power management improvements in Oracle Solaris, opportunities to further improve energy efficiency, and some future directions for Oracle Solaris power management.

  Read the article

• What's Bringing SharePoint 2007 Server to a hault?

  - by juanlarios

  I've been having issues with my teste environment and I'm hoping someone has run into this problem and can point me in the right direction. I noticed: SharePoint Server Memory is through the roof at times and so is the CPU usage. Most of CPU usage is a sql proccess. Running out of disk space all the time. I looked in the Logs located in the 12 hive and sure enough I have 1G log files that are hard to open because of the size. The following are the 3 error messages that are flooding my SharePoint logs:   04/05/2010 16:02:36.99     OWSTIMER.EXE (0x0B94)                       0x0BA4    Windows SharePoint Services       Timer                             5uuf    Monitorable    The previous instance of the timer job 'Variations Propagate Page Job Definition', id '{F9A73EB4-90FE-4574-AD99-B4034056F915}' for service '{F89169F9-707B-4588-9ED0-E6D399FE5E3D}' is still running, so the current instance will be skipped.  Consider increasing the interval between jobs.    04/05/2010 15:59:51.51     OWSTIMER.EXE (0x0B94)                       0x0BA4    Windows SharePoint Services       Timer                             5uuf    Monitorable    The previous instance of the timer job 'Profile Synchronization', id '{A05E3439-8DCD-449A-9D9E-46D601CACAA2}' for service '{F89169F9-707B-4588-9ED0-E6D399FE5E3D}' is still running, so the current instance will be skipped.  Consider increasing the interval between jobs.     04/05/2010 15:56:25.53     OWSTIMER.EXE (0x0B94)                       0x0BA4    Windows SharePoint Services       Timer                             5uuf    Monitorable    The previous instance of the timer job 'Scheduled Unpublish', id '{6298F93F-388D-46B9-809E-CEDBB8659661}' for service '{F89169F9-707B-4588-9ED0-E6D399FE5E3D}' is still running, so the current instance will be skipped.  Consider increasing the interval between jobs.     04/05/2010 15:54:14.73     OWSTIMER.EXE (0x0B94)                       0x0BA4    Windows SharePoint Services       Timer                             5uuf    Monitorable    The previous instance of the timer job 'Config Refresh', id '{C42DA970-3DA3-4AA2-94E5-8499C5B80A3E}' for service '{7F6D2CBE-8071-4A30-B313-7C9989FC2D87}' is still running, so the current instance will be skipped.  Consider increasing the interval between jobs.       I'm googling around but haven't found much. I know one other person posted something about this back in 2008, but no answers were reached. I have already checked the databases to see if any of them have gone offline for whatever reason, but from SQL everything is fine. I recently re-created an SSP and deleted an old ssp. So I thought maybe that was causing it, and who knows? maybe that causes some of the problems or maybe all. I'm running configuration wizard and see if anything changes. Please if someone has had similar issues let me know.

  Read the article

• Java Embedded Releases

  - by Tori Wieldt

  Oracle today announced a new product in its Java Platform, Micro Edition (Java ME) product portfolio, Oracle Java ME Embedded 3.2, a complete client Java runtime Optimized for resource-constrained, connected, embedded systems.  Also, Oracle is releasing Oracle Java Wireless Client 3.2, Oracle Java ME Software Development Kit (SDK) 3.2. Oracle also announced Oracle Java Embedded Suite 7.0 for larger embedded devices, providing a middleware stack for embedded systems. Small is the new big! Introducing Oracle Java ME Embedded 3.2  Oracle Java ME Embedded 3.2 is designed and optimized to meet the unique requirements of small embedded, low power devices such as micro-controllers and other resource-constrained hardware without screens or user interfaces. These include: On-the-fly application downloads and updates Remote operation, often in challenging environments Ability to add new capabilities without impacting the existing functions Support for hardware with as little as 130 kB RAM and 350 kB ROM Oracle Java Wireless Client 3.2 Oracle Java Wireless Client 3.2 is built around an optimized Java ME implementation that delivers a feature-rich application environment for mass-market mobile devices. This new release: Leverages standard JSRs, Oracle optimizations/APIs and a flexible porting layer for device specific customizations, which are tuned to device/chipset requirements Supports advanced tooling functions, such as memory and network monitoring and on-device tooling Offers new support for dual SIM functionality, which is highly useful for mass-market devices supported by multiple carriers with multiple phone connections Oracle Java ME SDK 3.2 Oracle Java ME SDK 3.2 provides a complete development environment for both Oracle Java ME Embedded 3.2 and Oracle Java Wireless Client 3.2. Available for download from OTN, The latest version includes: Small embedded device support In-field and remote administration and debugging Java ME SDK plug-ins for Eclipse and the NetBeans Integrated Development Environment (IDE), enabling more application development environments for Java ME developers. A new device skin creator that developers can use to generate their custom device skins for testing their applications. Oracle Embedded Suite 7.0 The Oracle Java Embedded Suite is a new packaged solution from Oracle (including Java DB, GlassFish for Embedded Suite, Jersey Web Services Framework, and Oracle Java SE Embedded 7 platform), created to provide value added services for collecting, managing, and transmitting data to and from other embedded devices.The Oracle Java Embedded Suite is a complete device-to-data center solution subset for embedded systems.  See Java Me and Java Embedded in Action Java ME and Java Embedded technologies will be showcased for developers at JavaOne 2012 in over 60 conference sessions and BOFs, as well as in the JavaOne Exhibition Hall. For business decision makers, the new event Java Embedded @ JavaOne you learn more about Java Embedded technologies and solutions.

  Read the article

• Graphics trouble after resuming from hibernate or suspend

  - by Voyagerfan5761

  I have a Dell Inspiron 2650 (with NVidia graphics, using nouveau drivers) that I'm using to try out Ubuntu. It's all great, except that Hibernate and Suspend aren't usable. Yes, I know that questions about power-save issues are rampant in the Linux support universe, but it seems that every time I find a solution it's for a very specific hardware combination and doesn't apply to me. So anyway, here goes. When I resume from either power-saving mode, I'll get graphics problems anywhere on the range from a few scattered random-colored pixels that won't change; all the way to full-screen patterns that don't change as I move the mouse, hit keys on the keyboard, or even bring up the shutdown dialog using the power button. Those full-screen issues (which may involve stripes with random pixels, partial black screen, or both) always end in me forcing the machine to shut down by holding the power button. I haven't done much testing yet to determine what severity level is most commonly associated with each mode, but I do avoid using either power-save option because of these issues. I'll add info on my hardware as I can gather it (no home internet connection, and this laptop is tethered to my desk by a dead battery and casing degradation). Please feel free to request something specific in the question comments. Hardware Info See this hardinfo report for my system's hardware configuration. (No, my username is not "myuser"; I sanitized hardinfo's output before publishing it.) Screenshots These screenshots are from a relatively mild occurrence, which happened after the second hibernation I took that session. The first one worked great, though I used the wireless card and Firefox heavily between the two hibernation attempts. Take a look at what happened when I opened my home directory in Nautilus and scrolled it: See below for the situations I've tested so far. The real trouble comes when the machine resumes to an unusable state; in such cases I can't even unlock the screen or properly reboot, much less take a screenshot. I have a hunch that putting a CD in the drive will cause such major failures, and I will try that at some point; see related question. Situations Tested Maverick (10.10) Suspend Seems to suspend nicely with nothing running Seems to suspend nicely with flash drive plugged in On resume from suspend with no flash drive, Terminal and gedit running: Funky graphics on top of log output, then blank screen with pixelated cursor; no response to power button (normally will shutdown 60 seconds later) Hibernate Seems to hibernate nicely with nothing running Seems to hibernate nicely with a few apps (Terminal, Mouse preferences) running Seems to not hibernate when flash drive plugged in Seems to not hibernate when System Monitor is running Have encountered failed hibernation (after several hours and one successful hibernate/thaw cycle) with no external media connected and no programs running except normal background stuff Natty LiveCD (11.04_2010-12-22) When I tested it, Natty wouldn't stay logged in. It played part of the login sound and then [ OK ] appeared in the top right corner (white-on-black terminal text) for a few seconds. Then it kicked me back to the Unlock screen. It did that four times before I gave up and just tested suspend from the Unlock screen. Suspend Resumed to vertical gray and black lines 2px (?) wide, then shifted to vertical "jail bars" of black over a black screen with above-described random pixels and mouse pointer. No apparent response to input from mouse (clicking randomly). Keyboard and touchpad unrecognized.

  Read the article

• Why would more CPU cores on virtual machine slow compile times?

  - by Sid

  [edit#2] If anyone from VMWare can hit me up with a copy of VMWare Fusion, I'd be more than happy to do the same as a VirtualBox vs VMWare comparison. Somehow I suspect the VMWare hypervisor will be better tuned for hyperthreading (see my answer too) I'm seeing something curious. As I increase the number of cores on my Windows 7 x64 virtual machine, the overall compile time increases instead of decreasing. Compiling is usually very well suited for parallel processing as in the middle part (post dependency mapping) you can simply call a compiler instance on each of your .c/.cpp/.cs/whatever file to build partial objects for the linker to take over. So I would have imagined that compiling would actually scale very well with # of cores. But what I'm seeing is: 8 cores: 1.89 sec 4 cores: 1.33 sec 2 cores: 1.24 sec 1 core: 1.15 sec Is this simply a design artifact due to a particular vendor's hypervisor implementation (type2:virtualbox in my case) or something more pervasive across more VMs to make hypervisor implementations more simpler? With so many factors, I seem to be able to make arguments both for and against this behavior - so if someone knows more about this than me, I'd be curious to read your answer. Thanks Sid [edit:addressing comments] @MartinBeckett: Cold compiles were discarded. @MonsterTruck: Couldn't find an opensource project to compile directly. Would be great but can't screwup my dev env right now. @Mr Lister, @philosodad: Have 8 hw threads, using VirtualBox, so should be 1:1 mapping without emulation @Thorbjorn: I have 6.5GB for the VM and a smallish VS2012 project - it's quite unlikely that I'm swapping in/out trashing the page file. @All: If someone can point to an open source VS2010/VS2012 project, that might be a better community reference than my (proprietary) VS2012 project. Orchard and DNN seem to need environment tweaking to compile in VS2012. I really would like to see if someone with VMWare Fusion also sees this (for VMWare vs VirtualBox compartmentalization) Test details: Hardware: Macbook Pro Retina CPU : Core i7 @ 2.3Ghz (quad core, hyper threaded = 8 cores in windows task manager) Memory : 16 GB Disk : 256GB SSD Host OS: Mac OS X 10.8 VM type: VirtualBox 4.1.18 (type 2 hypervisor) Guest OS: Windows 7 x64 SP1 Compiler: VS2012 compiling a solution with 3 C# Azure projects Compile times measure by VS2012 plugin called 'VSCommands' All tests run 5 times, first 2 runs discarded, last 3 averaged

  Read the article

• Issues with LVM partition size in Server 13.04

  - by Michael

  I am new to ubuntu and a little confused about how hard drive partitions and LVM works. I remember setting up Ubuntu server 13.04 and telling to to use 1TB of a 3TB server. Well I have maxed that out with blu-ray rips and want the rest of the drive for space. On log-in it says: System load: 2.24 Processes: 179 Usage of /: 88.7% of 912.89GB Users logged in: 0 Memory usage: 6% IP address for p5p1: 192.168.0.100 Swap usage: 0% => / is using 88.7% of 912.89GB lvdisplay outputs: --- Logical volume --- LV Path /dev/DeathStar-vg/root LV Name root VG Name DeathStar-vg LV Write Access read/write LV Creation host, time DeathStar, 2013-05-18 22:21:11 -0400 LV Status available # open 1 LV Size 2.70 TiB Current LE 707789 Segments 2 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 252:0 --- Logical volume --- LV Path /dev/DeathStar-vg/swap_1 LV Name swap_1 VG Name DeathStar-vg LV Write Access read/write LV Creation host, time DeathStar, 2013-05-18 22:21:11 -0400 LV Status available # open 2 LV Size 3.75 GiB Current LE 959 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 252:1 vgdisplay outputs: VG Name DeathStar-vg System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 2 Open LV 2 Max PV 0 Cur PV 1 Act PV 1 VG Size 2.73 TiB PE Size 4.00 MiB Total PE 715335 Alloc PE / Size 708748 / 2.70 TiB Free PE / Size 6587 / 25.73 GiB df outputs: Filesystem 1K-blocks Used Available Use% Mounted on /dev/mapper/DeathStar--vg-root 957238932 848972636 59634696 94% / none 4 0 4 0% /sys/fs/cgroup udev 1864716 4 1864712 1% /dev tmpfs 374968 1060 373908 1% /run none 5120 4 5116 1% /run/lock none 1874824 148 1874676 1% /run/shm none 102400 24 102376 1% /run/user /dev/sda2 234153 56477 165184 26% /boot And fdisk /dev/sda -l outputs: Disk /dev/sda: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders, total 5860533168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 1 4294967295 2147483647+ ee GPT Partition 1 does not start on physical sector boundary. I just don't know what to make of all this and am not sure how I can make it use all 2.73TBs. Thanks in advance for any help. EDIT-- Yes I did make changes to the LVM Config, but it didnt do anything. As requested, output of parted -l /dev/sda Model: ATA WDC WD30EFRX-68A (scsi) Disk /dev/sda: 3001GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2097kB 1049kB bios_grub 2 2097kB 258MB 256MB ext2 3 258MB 3001GB 3000GB lvm Model: ATA WDC WD30EFRX-68A (scsi) Disk /dev/sdb: 3001GB Sector size (logical/physical): 512B/4096B Partition Table: msdos Number Start End Size Type File system Flags Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/DeathStar--vg-swap_1: 4022MB Sector size (logical/physical): 512B/4096B Partition Table: loop Number Start End Size File system Flags 1 0.00B 4022MB 4022MB linux-swap(v1) Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/DeathStar--vg-root: 2969GB Sector size (logical/physical): 512B/4096B Partition Table: loop Number Start End Size File system Flags 1 0.00B 2969GB 2969GB ext4

  Read the article

• CES 2011–Microsoft Keynote Impressions

  - by guybarrette

  Microsoft has been kicking off the CES for a number of years by doing a keynote the evening of the event first day.  This year, SteveB talked about Xbox, Kinect, Windows 7 new laptops, Surface 2 and Windows vNext running on the ARM architecture. Some of the design of the new laptops showed are quite amazing.  This one has a dual screen with no physical keyboard.  The image is split between both screens.  A software keyboard appears when you place your 10 fingers on the lower screen. This one from Samsung has a sliding keyboard somewhat like numerous cell phones have. What I found the most amazing is that Intel was able to miniaturized a full Intel architecture (CPU, motherboard, memory) in a tiny form factor.  Imagine having the power of a full PC running .NET apps in a Zune/iPod form factor! They also showed V2 of the Surface device.  This one is called the Samsung SUR40 for Surface PC.  It’s much sleeker and it will likely loose the BAT (Big Ass Table) moniker  More info here SteveB announced that Windows vNext will run on ARM chips.  I’m intrigued by this announcement (you can read about it here) and I have many questions: -In the past ARM devices were slow, what now makes the ARM architecture able to run Windows? -ARM is 32-bit only, I think. -Does this mean that Intel wasn't able to provide such a lightweight architecture or simply that they weren't interested? -From what I understand, apps would need to be recompiled for ARM. Will we need to do that from an ARM PC or could it be done natively on Intel or on an Intel PC running in an ARM VM?  VS 2012? Ahhhh, smells like a cool PDC is coming up    Clearly it looks like PC have enough power for most of us right now and that the race is now about miniaturization, power consumption and battery life. You can watch the Microsoft CES 2011 keynote here var addthis_pub="guybarrette";

  Read the article

• Data structures for a 2D multi-layered and multi-region map?

  - by DevilWithin

  I am working on a 2D world editor and a world format subsequently. If I were to handle the game "world" being created just as a layered set of structures, either in top or side views, it would be considerably simple to do most things. But, since this editor is meant for 3rd parties, I have no clue how big worlds one will want to make and I need to keep in mind that eventually it will become simply too much to check, handling and comparing stuff that are happening completely away from the player position. I know the solution for this is to subdivide my world into sub regions and stream them on the fly, loading and unloading resources and other data. This way I know a virtually infinite game area is achievable. But, while I know theoretically what to do, I really have a few questions I'd hoped to get answered for some hints about the topic. The logic way to handle the regions is some kind of grid, would you pick evenly distributed blocks with equal sizes or would you let the user subdivide areas by taste with irregular sized rectangles? In case of even grids, would you use some kind of block/chunk neighbouring system to check when the player transposes the limit or just put all those in a simple array? Being a region a different data structure than its owner "game world", when streaming a region, would you deliver the objects to the parent structures and track them for unloading later, or retain the objects in each region for a more "hard-limit" approach? Introducing the subdivision approach to the project, and already having a multi layered scene graph structure on place, how would i make it support the new concept? Would you have the parent node have the layers as children, and replicate in each layer node, a node per region? Or the opposite, parent node owns all the regions possible, and each region has multiple layers as children? Or would you just put the region logic outside the graph completely(compatible with the first suggestion in Q.3) When I say virtually infinite worlds, I mean it of course under the contraints of the variable sizes and so on. Using float positions, a HUGE world can already be made. Do you think its sane to think beyond that? Because I think its ok to stick to this limit since it will never be reached so easily.. As for when to stream a region, I'm implementing it as a collection of watcher cameras, which the streaming system works with to know what to load/unload. The problem here is, i will be needing some kind of warps/teleports built in for my game, and there is a chance i will be teleporting a player to a unloaded region far away. How would you approach something like this? Is it sane to load any region to memory which can be teleported to by a warp within a radius from the player? Sorry for the huge question, any answers are helpful!

  Read the article

• Unable to configure/setup 5.1 audio with 12.04

  - by Vipin Vinayan

  I am kinda new to Ubuntu as well. I have been having this issue with audio for quite sometime now. Initially, when I installed version 11.10 (I guess), I was able to use my 5.1 speakers without any issues. If my memory serves me right, it was after an update that the 5.1 audio stopped working and the video resolution would not get saved. I temporarily fixed the resolution issue by creating a start-up shell script that would update the resolution and load it. But the issue with audio has been going on for quite sometime now. Even though I have option for 5.1, only two speakers seem to be working. I thought an upgrade should fix the issue and so upgraded the OS to version 12.04. I also tried uninstalling alsa and pulse audio, reinstalling them, changing the /etc/pulse/daemon.conf channels from 2 to 6. I have also tried installing pavucontrol but nothing seems to have worked and the issue still persists. Is there anything else you could suggest? The lspci log on my computer is as follows 00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10) 00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port (rev 10) 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 10) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01) 00:1d.0 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) 00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA Controller [IDE mode] (rev 01) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) Would really appreciate a response that will assist me in resolving my issue. Thanks in advance Vipin

  Read the article

• How employable am I as a programmer?

  - by dsimcha

  I'm currently a Ph.D. student in Biomedical Engineering with a concentration in computational biology and am starting to think about what I want to do after graduate school. I feel like I've accumulated a lot of programming skills while in grad school, but taken a very non-traditional path to learning all this stuff. I'm wondering whether I would have an easy time getting hired as a programmer and could fall back on that if I can't find a good job directly in my field, and if so whether I would qualify for a more prestigious position than "code monkey". Things I Have Going For Me Approximately 4 years of experience programming as part of my research. I believe I have a solid enough grasp of the fundamentals that I could pick up new languages and technologies pretty fast, and could demonstrate this in an interview. Good math and statistics skills. An extensive portfolio of open source work (and the knowledge that working on these projects implies): I wrote a statistics library in D, mostly from scratch. I wrote a parallelism library (parallel map, reduce, foreach, task parallelism, pipelining, etc.) that is currently in review for adoption by the D standard library. I wrote a 2D plotting library for D against the GTK Cairo backend. I currently use it for most of the figures I make for my research. I've contributed several major performance optimizations to the D garbage collector. (Most of these were low-hanging fruit, but it still shows my knowledge of low-level issues like memory management, pointers and bit twiddling.) I've contributed lots of miscellaneous bug fixes to the D standard library and could show the change logs to prove it. (This demonstrates my ability read other people's code.) Things I Have Going Against Me Most of my programming experience is in D and Python. I have very little to virtually no experience in the more established, "enterprise-y" languages like Java, C# and C++, though I have learned a decent amount about these languages from small, one-off projects and discussions about language design in the D community. In general I have absolutely no knowledge of "enterprise-y" technlogies. I've never used a framework before, possibly because most reusable code for scientific work and for D tends to call itself a "library" instead. I have virtually no formal computer science/software engineering training. Almost all of my knowledge comes from talking to programming geek friends, reading blogs, forums, StackOverflow, etc. I have zero professional experience with the official title of "developer", "software engineer", or something similar.

  Read the article

• eSTEP Newsletter for October 2013 now available

  - by uwes

  Dear Partners,We would like to let you know that the October'13 issue of our Newsletter is now available.The issue contains information on the following topics: Oracle Open World Summary Oracle Cloud: Oracle Engineered Systems Oracle Database and Middleware Oracle Applications and Software as a Service Oracle Industries Oracle Partners and the "Internet of Things" JavaOne News MySQL News Corporate News Create Your HR Strategic Vision at Oracle HCM World Oracle Database Protection Redefined A Preview: Oracle Database Backup Logging Recovery Appliance Oracle closed Tekelec acquisition Congratulations to ORACLE TEAM USA! Tech sectionARC M6 Oracle's SPARC M6 Oracle SuperCluster M6-32 - Oracle’s Most Scalable Engineered System Oracle Multitenant on SPARC Servers and Oracle Solaris Oracle Database 12c Enterprise Edition: Plug into the Cloud Oracle In-Memory Database Cache Oracle Virtual Compute Appliance New Benchmark-Results published (Sept. 2013) Video Interview: Elasticity, the Biggest Challenge Facing Data Centers Today Tech blog Announcing New Sun Storage 2500-M2 Drives SPARC Product Line Update ZFS RAID Calculator v6 What ships with ODA X3-2? Tech Article: Oracle Multitenant on SPARC Servers and Oracle Solaris New release of Sun Rack II capacity calculator available Announcing: Oracle Solaris Cluster Product Bulletin, September 2013 Learning & events Planned TechCasts Quarterly Partner Update Live Webcast: Simplify and Accelerate Oracle Database deployment with Oracle VM Templates Join us for OTN's Virtual Developer Day - Harnessing the Power of Oracle WebLogic and Oracle Coherence.Learn from OOW 2013 what is going on in Virtualization How to Implementing Early Arriving Facts in ODI, Part I and Part II: Proof of Concept Overview Multi-Factor Authentication in Oracle WebLogic Using multi-factor authentication to protect web applications deployed on Oracle WebLogic. If Virtualization Is Free, It Can't Be Any Good—Right? Looking beyond System/HW SOA and User Interfaces Overcoming the challenges to developing user interfaces in a service oriented References Vodafone Romania Improves Business Agility and Customer Satisfaction, with 10x Faster Business Intelligence Delivery and 12x Faster Processing Emirates Integrated Telecommunications Captures 47% Market Share in a Competitive Market, Thanks to 24/7 Availability Home Credit and Finance Bank Accelerates Getting New Banking Products to Market Extra A Conversation with Java Champion Johan VosYou can find the Newsletter on our portal under eSTEP News ---> Latest Newsletter. You will need to provide your email address and the pin below to get access. Link to the portal is shown below.URL: http://launch.oracle.com/PIN: eSTEP_2011Previous published Newsletters can be found under the Archived Newsletters section and more useful information under the Events, Download and Links tab. Feel free to explore and any feedback is appreciated to help us improve the service and information we deliver.Thanks and best regards,Partner HW Enablement EMEA

  Read the article

• Paper-free Customer Engagement

  - by Michael Snow

  v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} 12.00 Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-family:"Calibri","sans-serif"; mso-ascii- mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi- mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Appropriate repost from our friends at the AIIM blog: Digital Landfill -- John Mancini, supporting our mission of enabling customer engagement through better technology choices.  ---------- My wife didn't even give me a card for #wpfd - and they say husbands are bad at remembering anniversaries Well, today is the third World Paper Free Day.  I just got off the Tweet Jam, and there was a host of ideas for getting rid of -- or at least reducing -- paper. When we first started talking about "paper-free" most of the reasons raised to pursue this direction were "green" reasons.  I'm glad to see that the thinking has moved on to questions about how getting rid of paper and digitizing processes helps improve customer engagement.  And the bottom line.  And process responsiveness.  Not that the "green" reasons have gone away, but it's nice to see a maturation in the BUSINESS reasons to get rid of paper. Our World Paper Free Handbook (do not, do not, do not print it!) looks at how less paper in the workplace delivers significant benefits. Key findings show eliminating paper from processes can improve the responsiveness of customer service by 300 percent. Removing paper from business processes and moving content to PCs and tablets has the added advantage of helping companies adopt mobile-enable processes and eliminate elapsed time, lost forms, poor data and re-keying. To effectively mobile-enable processes and reduce reliance on paper, data should be captured as close to the point of origination as possible, which makes information easily available to whomever needs it, wherever they are, in the shortest time possible. This handbook summarizes the value of automating manual, paper-based processes. It then goes a step beyond to provide actionable steps that will set you on the path to productivity, profitability, and, yes, less paper.  Get your copy today and send the link around to your peers and colleagues.  Here's the link; please share it! http://www.aiim.org/Research-and-Publications/Research/AIIM-White-Papers/WPFD-Revolution-Handbook And don't miss out on the real world discussions about increasing engagement with WebCenter in new webinars being offered over the next couple of weeks:  October 30, 2012:  ResCare Solves Content Lifecycle Challenges with Oracle WebCenter November 1, 2012: WebCenter Content for Applications: Streamline Processes with Oracle WebCenter Content Management for Human Resources Applications Available On-Demand:  Using Oracle WebCenter to Content-Enable Your Business Applications

  Read the article

• Indefinite loops where the first time is different

  - by George T

  This isn't a serious problem or anything someone has asked me to do, just a seemingly simple thing that I came up with as a mental exercise but has stumped me and which I feel that I should know the answer to already. There may be a duplicate but I didn't manage to find one. Suppose that someone asked you to write a piece of code that asks the user to enter a number and, every time the number they entered is not zero, says "Error" and asks again. When they enter zero it stops. In other words, the code keeps asking for a number and repeats until zero is entered. In each iteration except the first one it also prints "Error". The simplest way I can think of to do that would be something like the folloing pseudocode: int number = 0; do { if(number != 0) { print("Error"); } print("Enter number"); number = getInput(); }while(number != 0); While that does what it's supposed to, I personally don't like that there's repeating code (you test number != 0 twice) -something that should generally be avoided. One way to avoid this would be something like this: int number = 0; while(true) { print("Enter number"); number = getInput(); if(number == 0) { break; } else { print("Error"); } } But what I don't like in this one is "while(true)", another thing to avoid. The only other way I can think of includes one more thing to avoid: labels and gotos: int number = 0; goto question; error: print("Error"); question: print("Enter number"); number = getInput(); if(number != 0) { goto error; } Another solution would be to have an extra variable to test whether you should say "Error" or not but this is wasted memory. Is there a way to do this without doing something that's generally thought of as a bad practice (repeating code, a theoretically endless loop or the use of goto)? I understand that something like this would never be complex enough that the first way would be a problem (you'd generally call a function to validate input) but I'm curious to know if there's a way I haven't thought of.

  Read the article

• Cloud Computing Pricing - It's like a Hotel

  - by BuckWoody

  I normally don't go into the economics or pricing side of Distributed Computing, but I've had a few friends that have been surprised by a bill lately and I wanted to quickly address at least one aspect of it. Most folks are used to buying software and owning it outright - like buying a car. We pay a lot for the car, and then we use it whenever we want. We think of the "cloud" services as a taxi - we'll just pay for the ride we take an no more. But it's not quite like that. It's actually more like a hotel. When you subscribe to Azure using a free offering like the MSDN subscription, you don't have to pay anything for the service. But when you create an instance of a Web or Compute Role, Storage, that sort of thing, you can think of the idea of checking into a hotel room. You get the key, you pay for the room. For Azure, using bandwidth, CPU and so on is billed just like it states in the Azure Portal. so in effect there is a cost for the service and then a cost to use it, like water or power or any other utility. Where this bit some folks is that they created an instance, played around with it, and then left it running. No one was using it, no one was on - so they thought they wouldn't be charged. But they were. It wasn't much, but it was a surprise.They had the hotel room key, but they weren't in the room, so to speak. To add to their frustration, they had to talk to someone on the phone to cancel the account. I understand the frustration. Although we have all this spelled out in the sign up area, not everyone has the time to read through all that. I get that. So why not make this easier? As an explanation, we bill for that time because the instance is still running, and we have to tie up resources to be available the second you want them, and that costs money. As far as being able to cancel from the portal, that's also something that needs to be clearer. You may not be aware that you can spin up instances using code - and so cancelling from the Portal would allow you to do the same thing. Since a mistake in code could erase all of your instances and the account, we make you call to make sure you're you and you really want to take it down. Not a perfect system by any means, but we'll evolve this as time goes on. For now, I wanted to make sure you're aware of what you should do. By the way, you don't have to cancel your whole account not to be billed. Just delete the instance from the portal and you won't be charged. You don't have to call anyone for that. And just FYI - you can download the SDK for Azure and never even hit the online version at all for learning and playing around. No sign-up, no credit card, PO, nothing like that. In fact, that's how I demo Azure all the time. Everything runs right on your laptop in an emulated environment.  

  Read the article

• What's wrong with my wireless?

  - by dazzle

  I am having issues with my wireless connection. My connection is constantly disconnecting, then attempting to reconnect, reconnecting momentarily, then disconnecting etc. on times scales that range from seconds to minutes. In the meantime, needless to say I'm having significant packet loss. I'm running Ubuntu 14.04 64bit, updated and upgraded to today. Here is my card and driver: delta@sager:~$ lspci -vq | grep -i wireless -B 1 -A 5 04:00.0 Network controller: Intel Corporation Wireless 7260 (rev 73) Subsystem: Intel Corporation Dual Band Wireless-AC 7260 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at f7d00000 (64-bit, non-prefetchable) [size=8K] Capabilities: Kernel driver in use: iwlwifi Here is my kernel: delta@sager:~$ uname -r 3.13.0-34-generic None of the other machines on my home network are having these issues. Windows Vista is networking without issue for goodness sake ;-) Here is a small clipping from the output of dmesg. As you can see, I am getting a cfg80211 message of some sort over and over again (FYI, I've replaced my MAC address with a series of dashes, so anytime there is a ---------------, that was where the MAC address was: [ 1881.739161] wlan1: authenticate with --------------- [ 1881.741561] wlan1: send auth to --------------- (try 1/3) [ 1881.743440] wlan1: authenticated [ 1881.746027] wlan1: associate with --------------- (try 1/3) [ 1881.749244] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1881.754727] wlan1: associated [ 1881.754827] cfg80211: Calling CRDA for country: US [ 1881.761552] cfg80211: Regulatory domain changed to country: US [ 1881.761559] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1881.761564] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1881.761568] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1881.761571] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761574] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761577] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761580] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1881.761584] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1882.391038] cfg80211: Calling CRDA to update world regulatory domain [ 1882.396254] cfg80211: World regulatory domain updated: [ 1882.396260] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1882.396265] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396268] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396271] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1882.396274] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396277] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.148252] wlan1: authenticate with --------------- [ 1886.150005] wlan1: send auth to --------------- (try 1/3) [ 1886.151807] wlan1: authenticated [ 1886.154847] wlan1: associate with --------------- (try 1/3) [ 1886.158147] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1886.163464] wlan1: associated [ 1886.163520] wlan1: Limiting TX power to 30 (30 - 0) dBm as advertised by --------------- [ 1886.163588] cfg80211: Calling CRDA for country: US [ 1886.170500] cfg80211: Regulatory domain changed to country: US [ 1886.170508] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1886.170513] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1886.170517] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1886.170520] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170523] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170526] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170529] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1886.170533] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1887.200197] cfg80211: Calling CRDA to update world regulatory domain [ 1887.203655] cfg80211: World regulatory domain updated: [ 1887.203659] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1887.203662] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203664] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203666] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1887.203668] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203670] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) I've poked around on AskUbuntu, and have not found any adequate solutions; have also found similar threads that were left unanswered. Any advice/experience/threads I might be able to pull on would be greatly appreciated. In your opinion, is this a kernel issue, hardware issue, etc.? Thanks in advance. EDIT: chili, here's the output of iwconfig: delta@sager:~$ iwconfig wlan1 IEEE 802.11abg ESSID:"LANbeforetime" Mode:Managed Frequency:2.412 GHz Access Point: ----------- Bit Rate=48 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=44/70 Signal level=-66 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:80 Missed beacon:0 eth0 no wireless extensions. lo no wireless extensions.

  Read the article

• Behaviour Trees with irregular updates

  - by Robominister

  I'm interested in behaviour trees that aren't iterated every game tick, but every so often. (Edit: the tree could specify how many frames within the main game loop to wait before running its tick function again). Every theoretical implementation I have seen of behaviour trees talks of the tree search being carried out every game update - which seems necessary, because a leaf node (eg a behaviour, like 'return to base') needs to be constantly checked to see if is still running, failed or completed. Can anyone suggest how I might start implementing a tree that isnt run every tick, or point me in the direction of good material specific to this case (I am struggling to find anything)? My thoughts so far: action leaf nodes (when they start) must only push some kind of action object onto a list for an entity, rather than directly calling any code that makes the entity do something. The list of actions for the entity would be run every frame (update any that need to run, pop any that have completed from the list). the return state from a given action must be fed back into the tree, so that when we run the tree iteration again (and reach the same action leaf node - so the tree has so far determined that we ought to still be trying this action) - that the action has completed, or is still running etc. If my actual action code is running from an action list on an entity, then I possibly need to cancel previously running actions in the list - i am thinking that I can just delete the entire stack of queued up actions. I've seen the idea of ActionLists which block lower priority actions when a higher priority one is added, but this seems like very close logic to behaviour trees, and I dont want to be duplicating behaviour. This leaves me with some questions 1) How would I feed the action return state back into the tree? Its obvious I need to store some information relating to 'currently executing actions' on the entity, and check that in the tree tick, but I can't imagine how. 2) Does having a seperate behaviour tree (for deciding behaviour) and action list (for carrying out actual queued up actions) sound like a reasonable approach? 3) Is the approach of updating a behaviour tree irregularly actually used by anyone? It seems like a nice idea for budgeting ai search time when you have a lot of ai entities to process. (Edit) - I am also thinking about storing a single instance of a given behaviour tree in memory, and providing it by reference to any entity that uses it. So any information about what action was last selected for execution on an entity must be stored in a data context relative to the entity (which the tree can check). (I am probably answering my own questions as i go!) I hope I have expressed my questions adequately! Thanks in advance for any help :)

  Read the article

• No wireless connection using a conceptronic c54i (RT2561/RT61 rev B)

  - by jrosell

  Detected but not working. New install on ubuntu 11.10 using coneptronic C54Ri. As documentation says it uses Ralink drivers.... Any ideas why my wireless does not work? $ lspci -nn | grep -i 'ralink' 01:05.0 Network controller: Ralink corp. RT2561/RT61 rev B 802.11g ifconfig eth0 Link encap:Ethernet HWaddr 00:1e:90:e5:af:13 inet addr:192.168.0.197 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::21e:90ff:fee5:af13/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28361 errors:0 dropped:0 overruns:0 frame:0 TX packets:16858 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:39812172 (39.8 MB) TX bytes:1633405 (1.6 MB) Interrupt:43 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:80 errors:0 dropped:0 overruns:0 frame:0 TX packets:80 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6608 (6.6 KB) TX bytes:6608 (6.6 KB) iwconfig wlan0 wlan0 IEEE 802.11abg ESSIDff/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff lsmod | grep rt rt61pci 27493 0 crc_itu_t 12627 1 rt61pci rt2x00pci 14202 1 rt61pci rt2x00lib 48114 2 rt61pci,rt2x00pci mac80211 272785 2 rt2x00pci,rt2x00lib cfg80211 172392 2 rt2x00lib,mac80211 eeprom_93cx6 12653 1 rt61pci parport_pc 32114 1 parport 40930 3 ppdev,parport_pc,lp lsmod | grep rt [ 2497.816989] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.827112] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.837430] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847528] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847632] phy0 -> rt61pci_wait_bbp_ready: Error - BBP register access faile d, aborting. [ 2497.847637] phy0 -> rt61pci_set_device_state: Error - Device failed to enter state 4 (-5). sudo lshw -C network *-network DISABLED description: Wireless interface product: RT2561/RT61 rev B 802.11g vendor: Ralink corp. physical id: 5 bus info: pci@0000:01:05.0 logical name: wlan0 version: 00 serial: fa:b8:14:58:62:35 width: 32 bits clock: 33MHz capabilities: pm cap_list ethernet physical wireless configuration: broadcast=yes driver=rt61pci driverversion=3.0.0-12-generic firmware=0.8 latency=0 link=no multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:fdef8000-fdefffff iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Failed to read scan data : Network is down uname -mr 3.0.0-12-generic i686 Edit 1 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no On reboot, sudo lshw -C network returns network is ok. Hovever, WPA keeps on asking the wireless key

  Read the article

• Software Tuned to Humanity

  - by Phil Factor

  I learned a great deal from a cynical old programmer who once told me that the ideal length of time for a compiler to do its work was the same time it took to roll a cigarette. For development work, this is oh so true. After intently looking at the editing window for an hour or so, it was a relief to look up, stretch, focus the eyes on something else, and roll the possibly-metaphorical cigarette. This was software tuned to humanity. Likewise, a user’s perception of the “ideal” time that an application will take to move from frame to frame, to retrieve information, or to process their input has remained remarkably static for about thirty years, at around 200 ms. Anything else appears, and always has, to be either fast or slow. This could explain why commercial applications, unlike games, simulations and communications, aren’t noticeably faster now than they were when I started programming in the Seventies. Sure, they do a great deal more, but the SLAs that I negotiated in the 1980s for application performance are very similar to what they are nowadays. To prove to myself that this wasn’t just some rose-tinted misperception on my part, I cranked up a Z80-based Jonos CP/M machine (1985) in the roof-space. Within 20 seconds from cold, it had loaded Wordstar and I was ready to write. OK, I got it wrong: some things were faster 30 years ago. Sure, I’d now have had all sorts of animations, wizzy graphics, and other comforting features, but it seems a pity that we have used all that extra CPU and memory to increase the scope of what we develop, and the graphical prettiness, but not to speed the processes needed to complete a business procedure. Never mind the weight, the response time’s great! To achieve 200 ms response times on a Z80, or similar, performance considerations influenced everything one did as a developer. If it meant writing an entire application in assembly code, applying every smart algorithm, and shortcut imaginable to get the application to perform to spec, then so be it. As a result, I’m a dyed-in-the-wool performance freak and find it difficult to change my habits. Conversely, many developers now seem to feel quite differently. While all will acknowledge that performance is important, it’s no longer the virtue is once was, and other factors such as user-experience now take precedence. Am I wrong? If not, then perhaps we need a new school of development technique to rival Agile, dedicated once again to producing applications that smoke the rear wheels rather than pootle elegantly to the shops; that forgo skeuomorphism, cute animation, or architectural elegance in favor of the smell of hot rubber. I struggle to name an application I use that is truly notable for its blistering performance, and would dearly love one to do my everyday work – just as long as it doesn’t go faster than my brain.

  Read the article

• Fail to start windows after Ubuntu 11.10 install

  - by user49995

  Computer: HP Pavilion dv7-6140eo OS: Originally Win7 I recently decided to try out Ubuntu, and I decided to dual-boot it with Windows 7. First I googled some how-to's, then I downloaded Ubuntu onto a memory stick and made a second partition (I originally only had one partition that I shrunk and used the unallocated space to install onto during the Ubuntu install). During the install I set format type to xt4 (or something, it was the default option), chose the "in the beginning" option and set the last option as "\". The install was successful. Although, when I restarted my computer I weren't able to choose which operating system to start; it went right into windows. After showing the windows logo for half a second before rebooting, I get a blue screen (see bottom of the page). Trying to fix it, I deleted the newly made partition I had just installed Ubuntu onto (seeing it wasn't working either). This made no difference. I proceeded with installing Ubuntu again, so I would at least have a functioning computer, and now Ubuntu works fine (on it now). The only difference on start-up is that I get a Grub window asking me to between several options including Linux and Windows 7 (loader). Now, if I choose Windows 7, I get the message "Windows was unable to start. A recent software or hardware change might be the cause". It recommends me to choose the first option of the two it provides; to start start-up repair tool. The second option being starting windows normally. If I start windows normally, the same thing happens as earlier. My computer does not have a windows installation CD. Although, it has (at least it used to, if I haven't screwed that too up) a 17gb recovery partition. In addition I made an image of the computer onto a external hard drive when I first got it. Though, I have no idea how to use either. If anyone has any idea how I can make windows work again or reinstall it (already backed up my files) it would be greatly appreciated. I still prefer to dual boot between the two functioning operating systems, but I will settle for a functioning windows 7. Thanks a lot for any replies. Blue screen: A problem has been detected and Windows has been shut down to prevent damage to your computer. If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps: Check for viruses on your computer. Remove and newly installed hard drives or hard drive controllers. Check your hard drive to make sure it is properly configures and terminated. Run CMKDSK /F to check for hard drive corruption, and then restart your computer. Technical information: **STOP: 0x0000007B (0xFFFFF880009A97E8,0xFFFFFFFFC0000034, 0x0000000000000000,0x0000000000000000

  Read the article

< Previous Page | 583 584 585 586 587 588 589 590 591 592 593 594  | Next Page >