Search Results

Search found 16417 results on 657 pages for 'computer linguist'.

Page 588/657 | < Previous Page | 584 585 586 587 588 589 590 591 592 593 594 595  | Next Page >

• Reset sound volume in Windows 8

  - by Svish

  There seems to be a bug in Windows 8 causing the maximum volume to become lower than it really should be. I'm now at a stage where I put the volume up to max and the sound is still very low. I have a couple of Logitech Z-10 speakers with a display on them and when I touch the increase volume button on that it shows me the volume (but not able to increase it) is actually below middle even though Windows claims it to be maxed out. Is there any way I can reset the volume in Windows 8 so that I can get it up fully max again? A registry setting or something? Really don't want to have to reinstall windows or drivers or anything like that cause if it is a bug it'll probably happen again and I really don't want to have to do that every time this happens :p Any ideas? Manged to fix it by unplugging the usb connection to my speakers, turning the volume down on my computer and up on the speakers, and finally reconnecting the usb connection. Seems to have been an issue with the speakers and not Windows this time. BUT, I'm still curious how you can adjust/reset the Windows 8 sound volume without using the volume controls. Like, where is the value of the current volume setting(s) really stored? And can you manually adjust them?

  Read the article

• How to disable monitor auto detection in Windows 7?

  - by Jay Yother

  I am currently running Windows 7 Ultimate 64-bit with a dual monitor setup with an NVIDIA 7950 GT graphics card. One monitor is dedicated to this machine and the other monitor is connected to a DVI KVM switch. When I switch to my other computer, Windows 7 disables the monitor. However, when I switch back it does not re-enable the monitor. The only circumstance that automatically re-enables the second monitor is when I switch back after Windows has put the monitors into power save mode. I am continually having to bring up the NVIDIA control panel to have it re-enable the monitor. Under Windows XP I would just disable the NVIDIA service to prevent it from auto-detecting the monitor (which doesn't solve the problem under Win7), and in Vista there was a registry hack that would prevent this. It looks as though that has been removed in Windows 7. I have found similar questions posted on this site, but nothing that matches my problem exactly. The following link is the question that comes the closest, but does not provide a solution to the problem. http://superuser.com/questions/96683/how-to-fix-monitor-detection-on-windows-7 Is there a way in Windows 7 to disable monitor auto-detection? Update: I just added a second graphics card to my Windows 7 64-bit machine. I plugged one monitor into each graphics card. Now, when I use the KVM switch to switch back and forth it will re-enable the second monitor like it should. There are however, a few quirks with this. If I have a program maximized on the second monitor and it has focus, when I switch it will move to monitor 1. If I have a program maximized on the second monitor and it does not have focus, when I switch it will behave like it is minimized and when I bring it back up it will show up maximized on monitor 1. Definitely better than it was, but still looking for a way to disable the auto-detection.

  Read the article

• Drive security settings in Windows 8 Pro

  - by Donotalo

  My PC OS is Windows 8 Pro x64. Windows 8 seems confusing. D:\ drive is supposed to be used solely by a single user, who is in Users group of the PC. The requirement is... that user will have full control of D drive. Admins will have full control of D drive. All other users can only list drive contents. No file could be opened. My account is admin account. From D drive's property Security tab, I've set the following: Allow "List folder contents" for Authenticated Users group. Allow "Full control" for SYSTEM. Allow "Full control" to specific user, who's supposed to use the drive. Allow "Full control" for Administrators group of the computer. Allow "List folder contents" for Users group. After setting this up, the specific user have full control of D drive. No other user can open any file on D drive. But though my account is an admin account, no file on D drive could be opened from my account! Why is this happening and how files can be opened from my account? Note: All accounts in this PC are local accounts.

  Read the article

• OS X Application icons missing after filesystem tampering

  - by dylan

  A while back I installed some Google software, I forget what it was, but it was something that attached itself to Google Chrome and was un-uninstallable short of uninstalling all of Chrome. It was a total pain in the a$$. Anyways, I was trying to put up a fight before going nuclear and just wiping Chrome, and during that fight, something went wrong (i.e., I didn't know what I was doing). I remember messing around with the Applications folder somehow. I don't remember what exactly I did, but it perhaps involved some interchanging between the /Applications and /User/Username/Applications folders? Definitely some tampering in those areas, I'm sure at least about that. Anyways, I've since updated and restarted my computer. Now, while all my apps work fine, many of them have blank icons - not on the Dock, those icons are fine, but in Spotlight search results, etc. Currently, my /Applications folder contains only OS X-cooked-in applications. My ~/Applications folder contains cooked in apps AND post-OS/third-party apps. There hasn't been any functionality deficit so far, but I don't like working on a machine where something isn't how it should be. I know my information was vague, but does anyone know what went wrong / how to fix it? OS X Mavericks 10.9.3

  Read the article

• Recovering data from an external hard drive

  - by CCallaghan

  I have a WD Elements 2GB hard drive (formatted NTFS). I accidentally kicked out the USB cable while writing data to the disk, and now I can't access most of the data. Although this was ostensibly my backup drive, there is a great deal of important material on there which was only on there. I realise how idiotic this makes me. (So, formatting is not an option.) Things I've tried/information I've gathered: Windows Explorer will recognise the drive itself. However, it will not access most directories therein (and will sometimes crash when exploring). I can access all of the directories through the command line, but the dir command will often report that it can't read any files in most of the directories. The situation was similar when I hooked it up to an Ubuntu machine: the file explorer crashed, but I could access directories - but not files in those directories - via terminal commands. Several files I tried to copy out either resulted in an I/O error being reported or resulted in the command line crashing. The Disk Management utility on Windows reports a healthy disk formatted as NTFS and not RAW. It also indicates the correct amount of space used up and its capacity (so it seems that the files are not deleted). I've tried to run chkdsk, but that hangs on Step 2 (checking indexes) at 74%. Step 1 reported no bad sectors. I tried Recuva, but that didn't seem to work (stalled at 0% for half an hour). I should also note that the disk doesn't seem to be spinning smoothly; it seems to be chopping back, like it's reading the same sector over and over again. I noticed this after I kicked out the cable. Any help would be greatly appreciated. Update: It would seem the problem has taken a turn for the worse. The external hard drive now shows up on my computer as a local disk and is not mountable by Linux.

  Read the article

• is there a man in the middle attacking to my server machine?

  - by GongT

  My server works well about half a year. But a strange thing happened (several hours before). This server has two IP-address 58.17.85.19 & 117.21.178.19 When I navigate to http://58.17.85.19, nothing different as before. But http://117.21.178.19 will return a "302 Object moved" and become a "redirect loop" I do some test: ($cmd = "wget http://117.21.178.19/?xx=$RANDOM --max-redirect 0 -S --no-cache -O -") Step by step: run $cmd on my PC and my firend's one (we live in two side of China, far away). - got 302 run $cmd on this server - got 200 OK (content is correct result of index.php) run $cmd on another server in same computer room - got 200 OK telnet from my PC and build an HTTP request (type by hand) - got 200 OK shutdown php-fpm, run $cmd on my PC - got 302 run $cmd on server - 502 Bad Gateway shutdown nginx, run $cmd on both the server and my PC - Connection refused. create iptables rule, refuse any connection to 58.17.85.19:80. run nc -l 80 -k -vvv on server and run $cmd on my PC NC show me that.... Server accept connection (Connection from [my ip]) My connection closed ! (Remove fd xx from list) wget dump out response - got 302 I know that, normaly, NC will accept connection, then dump HTTP request from client, and client will wait for response. this connection will open forever(infact client will close connection becouse timeout), becouse NC can't give any response. So... where my request gone? who send an response to the client? some virus on my server system? If so, why 58.17.85.19 didn't has this error? or... I was attacked by a middleman?

  Read the article

• Can’t connect to SQL Server 2008 - looks like Shared Memory problem

  - by Proposition Joe

  I am unable to connect to my local instance of SQL Server 2008 Express using SQL Server Management Studio. I believe the problem is related to a change I made to the connection protocols. Before the error occurred, I had Shared Memory enabled and Named Pipes and TCP/IP disabled. I then enabled both Named Pipes and TCP/IP, and this is when I started experiencing the problem. When I try to connect to the server with SSMS (with either my SQL server sysadmin login or with windows authentication), I get the following error message: A connection was successfully established with the server, but then an error occurred during the login process. (provider: Named Pipes Provider, error: 0 - No process is on the other end of the pipe.) (Microsoft SQL Server, Error: 233) Why is it returning a Named Pipes error? Why would it not just use Shared Memory, as this has a higher priority order in the list of connection protocols? It seems like it is not listening on Shared Memory for some reason? When I set Named Pipes to enabled and try to connect, I get the same error message. My windows account is does not have administrator priviliges on my computer - perhaps this is making a difference in some way (as some of the discussions in this post about an "SuperSocketNetLib\Lpc" registry key seems to suggest). I have tried restarting the SQL Server service, by the way, and also tried to get someone to log onto the machine with an admin account to restart the SQL Server service. Still no luck.

  Read the article

• Windows 7 does not detect my new hard drive?

  - by jasondavis

  I just built a really nice new PC. Some specs... Intel i7-930 CPU ASRock Extreme X58 motherboard with sata 3 and USB 3.0 12gb of G-Skill DDR3 RAM 80gb Intel G2 Solid state drive for Windows 7 and other programs to run on Windows 7 Pro 64bit OS 2 1gb grapghic cards for 4 monitor support Thats the main components. Well today my new 1tb western digital hard drive came which I plan to use for data to preserve the life of my SSD (hopefully). I hooked up it's sata power input and then hooked up it's sata data cable to a sata 2 port on my motherboard, I boot windows 7 and go into my computer and the drive is not showing up with my other drives. I then re-boot again and check again, no luck. I then shut down the PC and open the case back up, I then check my connections and they all look good. I then boot up and I can see the new HD is on and spinning. I then go into my BIOS settings to see if it registers there and it DOES! It shows I have a WD 1tb hard drvie on sata 2 port 6. So I am at a loss of why it is not showing up as an option in windows? Windows acts as if the drive is not there. Please help

  Read the article

• How do I disable tablet gestures in windows 8?

  - by ???

  I'm using a Wacom Intuos4 and I have recently upgraded to Windows 8. I don't have a problem when using Photoshop however I occasionally draw on flash based online boards. The problem is, when I drag the pen in a direction repetitively (which is basically all I do when drawing) it's detected as a gesture, sometimes causing Chrome to go to the previous page (left drag) and making me lose the entire thing. Is there a way to disable these "gestures"? I believe this is not something caused by Windows 8 (or Charms) because I run Windows in English although it's not the initial language that Windows was installed in. I changed to English long after the installation. When Windows takes a move as a gesture, a small text pops up next to the cursor informing me about what I have just done and those pop ups are not even in English. I'm sorry for failing to be any more specific here but these gestures could be a feature of either Windows (unlikely), the tablet, Chrome or the computer itself. It's an Acer Aspire and it has one of those little stickers on it that specifies some of the features and one of them reads "Multi-Gesture" (referring to the touchpad, I guess). Could it be that this Multi-Gesture feature somehow decided to expand and apply for my tablet as well? If so, how do I disable it?

  Read the article

• Cannot change power button or lid close action

  - by Mark Henderson

  I have a Samsung 900x laptop and I want to change it so that when I close the lid, nothing happens (I often close the lid to carry it somewhere 10 seconds away, and by putting it into suspend it cancels any active downloads/etc). Easy, right? Go to Power Options and change it there; just like on every other laptop in the world. Not so fast: Saywhat?! That message only shows up for the nodes for Lid Close Action, Power Button and Sleep Button. I can change every other setting except for those three. I'm definately an Administrator on the computer, and I've googled the error and found dozens of hits on other crappy forums, but of course nothing on those worked (otherwise, I wouldn't be here). And as ususal the "Why can't..." hyperlink gives no useful infomation what so ever (just a generic Help document). So - how can I change what closing the lid does? I will modify the registry directly if I have to.

  Read the article

• VirtualName-based local development host behind corporate proxy (MAMP)

  - by geerlingguy

  I am behind a corporate proxy server/firewall, and this firewall seems to not be too happy with my idea of local development. On my home computer (Mac/Leopard), I have MAMP running, with a rule in /etc/hosts that directs dev.example.com to 127.0.0.1, and I have a virtualhost set up in the httpd.conf file which works great for me. However, at work, I set up the exact same configuration, but am not able to access dev.example.com, likely due to some address/DNS translation going on via the proxy server. Here are the relevant details from Terminal: $ ping dev.example.com PING dev.example.com (127.0.0.1): 56 data bytes 64 bytes from 127.0.0.1: icmp_seq=0 ttl=64 time=0.025 ms $ host dev.example.com Host dev.example.com not found: 3(NXDOMAIN) I've tried adding dev.example.com to the list of bypass addresses in System Preferences (the 'Bypass proxy settings for these Hosts & Domains' list), but that had no effect. Is there any way I can develop locally using name-based hosts at work? I can access localhost, but can't get to the dev.example.com (or any other custom virtualhosts) here at work, which complicates other matters related to the sites on which I'm working...

  Read the article

• Graphics artifacts/distortion with Win7 and nVidia

  - by Gepard

  Problem I encounter is rather hard to describe, so I provide a screenshot: http://dl.dropbox.com/u/1732760/video-distortion.png As you can see there are some horizontal stripes in random colors. These stripes appear sometimes in all windowed apps, games and on the desktop too. They tend to stay in place until I refresh window (or force it to to redraw by for example minimizing and maximizing again). They also tend to appear in the same place and shape multiple times, even if they disappear, it's very likely they will be again in the same place after a while. These artifacts do not blink or change if computer is idling. If I don't touch anything, do not use mouse, they will stay in place forever (unless some app redraws its window on its own). I first encountered this problem some weeks ago. Back then I thought it might be cooling problem, so I took out the graphics card, removed dust from the radiator and fan and put it into PC back. I also ran some stress test using Furmark (peak tempearature was ~65C) to see if the problem becomes more intense if the card gets hotter, but suprisingly no artifacts whatsoever appear during the stress test. Graphic card is Galaxy GeForce 7300 GT with DDR3 memory, was never overclocked. Drivers are the latest, from Nvidia site. OS is Windows 7 64-bit, updated. AMD64 3000+, 2GB RAM. I'm running a dual monitor setup with 2 19'' Samsung LCDs and problem is on both, so I assume it's not a monitor or cable issue.

  Read the article

• Can Windows Media Player create playlists based on folder structure?

  - by Chaulky

  Over the years I've carefully molded my digital media collection into a series of folders that make it easy for me to find what I'm looking for. I recently discovered the awesomeness that is streaming video from Windows 7 Media Player to the PS3 so I can watch it on the big screen without all the hassle of hooking the computer up to the TV. The problem is, I totally lose my carefully crafted folder structure and all my videos become one giant mess again... not cool! As a temporary solution, I've created a few playlists for my favorites (Dexter Season 4, Dexter Season 5, Breaking Bad Season 1, etc.). This is a HUGE pain in the a$$. So, is there a way to get Windows Media Player (on Windows 7) to maintain some sort of folder structure based on the location of the actual video files? So if I have my videos sorted into folders by show and season, Media Player will pick that up and let me browse it in the same way. As an alternative answer, I'll accept suggestions for a program that can also stream to PS3 and has this "folder organization" feature.

  Read the article

• 2 routers at home- how to connect with VNC?

  - by Charles Leviton

  I have two routers at home. First router is upstairs and is connected to the cable modem. 2nd router is downstairs and acts as "signal booster" for the 1st router. Devices connected to the upstairs router have IP addresses of the form 192.168.1.n Devices connected to the upstairs router have IP addresses of the form 192.168.2.n. I blindly followed instructions from a website to do this set up, just glad it works! Upstairs I have a PC running Win 7 64 bit. Its assigned IP is 192.168.1.7. I have a VNC viewer running on this. Downstairs I have a 2nd PC running Vista 32 Home edition bit that is connected to the 2nd router and has IP Address 192.168.2.114. VNC server is running on this. It's listening on 5900. There is no firewall. When I try to connect to this downstairs PC from upstairs it fails with message "Failed to connect to server". I cannot ping to this either. If I try to connect to this downstairs PC using VNC Viewer from another computer that's connected to the same downstairs router then it works like a charm. So what's the work around if the viewer is on a different "network"? I don't have any problems doing remote desktop connection from the downstairs PC to the upstairs PC even if they are connected to different routers. Router information- Upstairs- ASUS RTN13U, downstairs- DD-WRT v24 RC-5 Thanks! P.S. I posted this on the Ultra VNC forum as well but that doesn't seem to have a lot of activity, so taking the liberty to multipost.

  Read the article

• Windows 7 automatically logs out when logging in

  - by Luke

  A Windows 7 HP x64 computer is set to automatically log in (no password), but once it starts logging in, it starts to load the desktop after the welcome screen, but before icons or background images are loaded, it goes to the Welcome screen saying 'Logging Off'. I can log in with Safe Mode, and I ran a couple different virus scans, with no detections. I also tried checking the userinit.exe file in System32 (as suggested by MANY users for Windows XP), but it's the same version as a working system. I also checked the registry under HKLM\Software\Microsoft\Windows NT\CurrentVersion\Winlogon for the SHELL and UserInit values, but they look normal. I tried to disable all startup items (through MSCONFIG) to select Diagnostic boot, but then I get a blue screen about the video driver not loading. Any other ideas? EDIT I created a new user, and it could log in no problems. I am thinking it's the NTUSER.DAT file. I just renamed it to NTUSER.DAT.old, then tried logging in as the problem user. I could log in, but as a TEMP profile. His profile folder is now C:\Users\TEMP, and his old folder is still accessible but in the wrong location. EDIT 2 I can't seem to turn off the TEMP profile, so I'm open to other suggestions. Copying the folders (i.e. Documents, Music, etc) does not work, as it creates an additional TEMP.000 then TEMP.001 folder each time the user logs in.

  Read the article

• Could replacing an old hard drive's circuit board make it work again?

  - by oscilatingcretin

  I have a 12-year-old, 10gb Maxtor drive that died on me around 7 years ago, but I have not had the heart to throw it away. When the computer powers on, it whirrs silently as it tries to spin up and then it stops. So, a few years ago, I sent it off for professional data recovery. They were able to retrieve quite a bit from it, but I know there's a bunch more there. It only cost $700, so I just chalked up the lackluster recovery effort to "you get what you pay for" considering that most companies will charge you several thousands of dollars for this kind of data recovery. When they sent the drive back, I couldn't help but plug it back in just to see if maybe they unjammed something in the process of disassembling/reassembling the drive. To my surprise, the drive had a much healthier spin-up sound and actually stayed spinning for several minutes before winding down to a halt. Windows is even able to detect and interact with the drive, but I get I/O errors after so many minutes of waiting for it to mount. Before I start doing stupid stuff with it like dropping it on the ground, freezing it, crapping on it, etc, I decided to buy the exact same model off Ebay so that I could swap the circuit boards as a last-ditch effort. While it's en route, I thought I'd come here to ask if this is even a worthwhile effort and, if even remotely so, what should I know before ripping off the old board and slapping on the new?

  Read the article

• How can I automate or script daily downloads for any new anti- virus databases, and then have the program scan my drive?

  - by Macgrimm

  Howdy all Super Users" I humbly ask if any Super User can direct this long time, gray haired Apple Tech in the right direction on this issue. I believe there probably are many ways to skin this cat. But I am looking to find simply the best, most unattended way to get it done. Any help will be greatly appreciated. also (I know there are much better softwares out there for the Mac so please don't go there! The politics of this company dictate which Anti virus we have to use) anyway without any further wait: basically I am trying to automate 2 very important functions of Mc'Afee anti-virus for Mac. First I want to automate the process of retrieving new virus definition files, and second I want to automate the process of scanning for viruses. It turns out that Using Mc'Afee Anti-Virus for the Mac are both manual functions. And they left up to the user (per user account) to perform. Depending on all of about 150 MAc users to perform these 2 tasks themselves is around 65% compliance. My question then is: If I wanted to use the command line such as (open /Applications/McAfee\ Security.app) It will open up the Security Console. But how can I make command Mc'Afee go out and grab the definition files and scan the computer? I have to admit I am at a crossroad and Macaltimers has set in. I would really appreciate it if any of you "Super ~ Users" can help me out with this MacAltimers loss of how to what to do. Thanks to All up Front Macgrimm

  Read the article

• What should I encrypt in Debian during install?

  - by ianfuture

  I have seen various guides and recommendations on web about how best to do this but nothing that clearly explains the best way and why. So I understand there is a need for part of Debian during install to be un-encrypted on its own partition to allow it to boot. Most info I have seen is call this /boot and set the boot flag. Next I believe the best approach is to create another partition out of all the rest of the disk space, encrypt this, then on top of that create a LVM and then within the LVM create my various partitions , name them , select size, and file system type. Can I include /swap in the encrypted LVM part ? Is this approach sound? If so what are the partitions I should use (this is going to be a minimal server install with a view to install as and when what I need for a dev server)? Finally how does the installer know what to put in each partition I define ? I appreciate there are more than one question but any help and suggestions would be appreciated. If further clarification is needed please mention in the comments . EDIT : 16/3/2010 After Richard Holloways reply I thought it relevant to add this info: The reasons why I want to do this are to explore maximising security on any server install and set up, due to interest in the area of Computer Security and Forensics. Also I am trying to peform the task as if it being performed in an enterprise situation. On a technical matter, once set up and configured with minimal packages and ssh this server will not physically be easy to access so I will only be entering via ssh. (Yes I know why encrypt something no one will ever be able to get their hands on? Because I can and I want to is the simple answer, but see above too).

  Read the article

• quad sli with gtx 690 not working

  - by Moaadh

  I have two cards GTX 690 (dual core). I did the Sli successfully. Nvidia control panel acknowledges the two cards as quad Sli. However, the problem is that Windows 7 64-bit Ultimate is showing me the graph memory size as 4 GB while it is supposed to be 8 GB because of the Sli. Also the benchmark from all software is giving me a very low score compared to some other guy's benchmark on YouTube. It gives me a big headache. Does anyone know why this is happening? If so, how can I get Windows 7 to recognize all 8 GB of memory? Thanks for your help in advance. My computer specifications: (Processor: Intel Core i7-3930k @3.2GHz(12CPUs))--- (Memory: 65536 MB Ram 1866 MHz)-- (OS: Windows 7 Ultimate 64-bit)-- (OCZ 240GB as SSD PCIe drive for booting and storage disk)-- (DirextX version: DirectX 11)-- (VGA Card: 2 X EVGA GTX 690 Dual GPU. Each GPU is 2 GB, so total memory should be 8 GB.)-- (MotherBoard: ASUS Rampage IV Extreme)-- Others with lesser specifications get a 2500 score in heaven benchmark while I get 1501 as if it is one card.

  Read the article

• Hard drive causing BSOD

  - by JoshIrving

  I've come across a problem after building my new PC and installing a clean Windows 7. I originally planed on a RAID 1 or 0 but after further research I decided against it. So I was left with two 1TB Western Digital Black SATA 6Gb/s hard drives. My plan now was to use my second hard drive as a backup (using Windows Backup or 3rd party software). I set both hard drives to AHCI in the BIOS and installed Windows 7. I went through the lengthy process of downloading and installing each driver manually (latest versions), using the motherboard disk for a list of what I need. After a few restarts and before installing any software, I took an image backup onto DVD and the second hard drive. First witnessed the problem during the first scheduled Windows backup. The progress bar froze at about 70% (doc backup done, image backup in progress). It stayed still for 2 hours until it blue screened. Next time the backup froze, I tried shutting down. It logged me out and got stuck at the last step ("Shutting down" and blue spinner) for an hour, until I hard shutdown. I later realised this hasn't got anything to do with the backup. I ended up blue screening on almost every shut down (same place). Turns out, it's because of the second hard drive spinning down or turning off. The computer will now shutdown properly, as long as I remember to read or write to the second drive before executing shutdown. I've now set "Turn off hard disk after: Never" - No problems, so far. Do I have dodgy hard drive(s) or should I investigate the POWER_STATE_DRIVER_FAILURE BSOD - can it be a driver issue? AHCI?

  Read the article

• How to set an executable white list?

  - by izabera

  Under Linux, is it possible to set a white-list of executables for a certain group of users? I need them to be unable to use, for example, make, gcc and executables on removable disks. How can this be done? Edit, let me explain better. I'm dealing with a high school IT system, young geeks that (during the lessons) want to play, surf the net, damage those computer however they can. The major step to achieve this goal was to remove the system they're familiar with and install Ubuntu in all the computers. This actually works quite well, but recent events proved that this is not enough. I want to allow them to execute certain safe programs, like Open Office, and to deny any other program, whether it is preinstalled software, something they carry in usb drives, a downloaded program or a script they program on site. It's possible to remove the 'x' permission on any file on the pc, but of course it would be impractical. Furthermore, they would be able to run anything they download. I thought the best solution would be to make a white-list of safe programs and to deny anything else, but I don't really know how to do it. Any idea is helpful.

  Read the article

• Windows 7 explorer crashing trying to read external hard disk

  - by Mario De Schaepmeester

  I have a 1TB Western Digital hard drive which is almost full and last time I tried to plug it into my laptop, I got a Windows dialog saying "this hard drive needs to be formatted". I did not panic because I have experienced things like this before and I know it's often solved by simply re-inserting the drive. Now however, whenever I plug it in and try to browse it in explorer by going to "computer", the explorer process crashes after a while. I simply close explorer since it takes ages trying to read the disk and nothing happens. After searching on the internet, the best thing to do would be a chkdsk. I tried it via properties in explorer (which also took a good 5 minutes to open up), locks up as well, after waiting a couple of minutes it says there's no access to the disk so a chkdsk is not possible... I want to make clear that I always use safe removal before pulling out the USB cable. Last time however, safe removal just would not work and when trying to shut down Windows, the logoff screen just would not disappear (I've waited at least 10 minutes or so) and I powered off the PC by force. This may be the cause of the problems but the disk was still recognised immediately after that. I really don't want to format this thing because it contains C: clones of 3 computers and a lot of other stuff that I don't want to re-copy. What would be the best course of action? Update I got chkdsk working via the command line. I used the /F and /R options. I already got a bunch of lines saying "file record segment X is unreadable" or whatever it is in English, my OS is Dutch. It looks bad... Will chdsk repair these errors?

  Read the article

• Is my motherboard failing, or is there some other issue?

  - by ThatGuy

  So, several months ago I put together my own desktop PC. I set up a dual boot to Windows and Ubuntu. Recently, without changing any settings or installing anything new, the wifi stopped working on windows (I use a wifi adapter). It said it was connected, Network settings showed that it was working and running trouble shooting had no results. My internet still works on any other device. I found that removing the adapter from the motherboard and plugging it back in was the only thing that fixed the problem. Reinstalling the wifi drivers did not help. I purchased a new Wifi adapter, but the problem persists. More recently, I had a much more discouraging development. Sometimes, turning on the computer results in a boot loop: BIOS never starts. Instead, the monitor turns on as if it got a signal, then immediately turns off. This loops on it's own indefinitely until I hold down power, hard reset it, and try again. Sometimes it works, sometimes it doesn't. I haven't tested much on the Ubuntu side. It appears that wifi works at least some of the time, but since I've had issues just getting to BIOS I'm not confident the issue is on the software side. I've also noticed issues with some of the USB ports no longer working, but that seems to be off and on. Finally, as of a few minutes ago, I booted to windows to discover that everything was running very slowly. Slow here is a relative word, but I have a Samsung 840 pro SSD and I'm used to applications running nigh instantly, and it was a solid 3 minutes before any of my applications would load. Anyway, my question is this: Is it likely that my motherboard is failing? Either way, what steps can I take to try and pin down the problem and figure out what to do?

  Read the article

• Are email addresses mandatory for Windows 8 login names?

  - by Cedric Martin

  I've got a computer running Windows 8 and in the user accounts I can see four accounts (they're in french, here's a rough translation): [email protected] / administrator Veronique YYY / [email protected] ASP.NET Machine Account / local account guest account / the guest account is desactivated I've got several questions but they're all related to email addresses and login names / accounts. Are email addresses mandatory for Windows 8 login names? Can you mix live and non-live user accounts on a Windows 8 system? Is it possible to have a live Windows 8 user account which is not using a @live.xx email address? Is it possible to have a non-live Windows 8 user account which is using a @live.xx email address? If the gmail.com email address of the admin is not a live Windows 8 account, does this mean I can create a "fake" email and use that as the email of a new Windows 8 account? Basically I don't understand very well why there are email addresses displayed on the login screen and why there are both @live.xx and @gmail.com email addresses on the same system and answer to the questions I asked above may help me understand a bit better what is going on (I'm coming from a Linux / OS X background. I literally haven't used Windows in more than a decade).

  Read the article

• Disk operations in windows 7 are slow

  - by Skadlig

  My computer started lagging last Sunday. I tried to reboot it and it failed. Trying to boot into failsafe mode takes around two hours. It mainly freezes on two files: scsiport.sys and classpnp.sys When it finally has started all disc operations are really slow. When it has run for a while it goes faster, probably due to data moved into RAM instead. It froze on an other file before that was associated with Avast but uninstalling it didn't really help. A critical windows update was installed on Sunday but rolling back the update didn't help. I had a guess about the sound card but disabling the sound card drivers also didn’t help. I have an inkling of an idea that it might be Intel rapid storage technology that might be acting up but it doesn't allow me to reinstall it from failsafe mode and I haven't been able to log into normal mode for a while. I would appreciate suggestions regarding how to get into normal mode again and/or what can be the root cause.

  Read the article

< Previous Page | 584 585 586 587 588 589 590 591 592 593 594 595  | Next Page >