Search Results

Search found 15939 results on 638 pages for 'low memory'.

Page 588/638 | < Previous Page | 584 585 586 587 588 589 590 591 592 593 594 595  | Next Page >

• ubuntu eth0 not reconnecting after cable unplugged

  - by Alex

  I'm running kubuntu 9.10 w/ gnome, I have a static IP defined in /etc/network/interfaces When I unplugged my network cable and rebooted, then reconnected the network cable I was not able to connect. I tried using sudo ifup eth0, and then ifconfig and it seemed as though the IP address had been assigned and I was connected, but I wasn't. I then did ifdown eth0, and again ifup eth0. For some reason I'm not able to access the network. Furthermore, I also attempted to connect via wlan, and was able to connect to the wireless network, but cannot "see" the network. I can't transfer data or access the internet or anything on the network including the router. How do I resolve this? topsy@monolyth:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1c:25:1c:df:70 inet addr:192.168.1.145 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:25ff:fe1c:df70/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5720 errors:0 dropped:0 overruns:0 frame:0 TX packets:565 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:378035 (378.0 KB) TX bytes:46832 (46.8 KB) Memory:fe000000-fe020000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) By access the network I mean the local network as well as the internet. topsy@monolyth:~$ ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=9.14 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=1.24 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=1.01 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=1.00 ms [snip... all OK, icmp_seq from 5-30, time between 0.981-1.25ms] ^C --- 192.168.1.1 ping statistics --- 30 packets transmitted, 30 received, 0% packet loss, time 29035ms rtt min/avg/max/mdev = 0.971/1.300/9.140/1.458 ms topsy@monolyth:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default 192.168.1.1 0.0.0.0 UG 100 0 0 eth0 root@monolyth:~# cat /etc/resolv.conf # Generated by NetworkManager

  Read the article

• SSD Fresh Does Not Start

  - by Jim Fell

  I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fress from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried shutting down the Spybot Resident and disabling the firewall and virus scanner with no luck. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

  Read the article

• What would make a noise in a PC on graphics operations on a passively-cooled system?

  - by T.J. Crowder

  I have this system based on the Intel D510MO motherboard, which is basically an Atom D510 (dual-core HT Atom w/built-in GPU), an Intel NM10 chipset, and a Realtek Gigabit LAN controller. It's entirely passively cooled. I noticed almost immediately that there was a kind of very, very soft noise that corresponded with graphics operations, sort of the noise you'd get if you had a sheet of flat paper and slid something really light across it — but more electronic than that. I wrote it off as observation error and/or disk activity triggered by the graphics operation (although the latter seemed like a lot of unnecessary disk activity). It isn't. I got curious enough that I finally did a few controlled experiments, and here's what I've determined: It isn't the HDD. For one thing, the sounds the HDD makes (when seeking, when reading or writing, when just sitting there spinning) is different. For another, I used sudo hdparm -y /dev/sda (I'm using Ubuntu 10.04 LTS) to temporarily put the disk on standby while making sure that non-disk graphics op was happening in a loop. The disk spun down, but the other sound continued, corresponding perfectly with the timing of the graphics op. (Then the disk spun up again, but it takes long enough that I could rule out the HDD.) It isn't the monitor; I ensured the two were well physically-separated and the sound was definitely coming from the main box. It isn't something else in the room; the sound is coming from the box. It isn't cross-talk to an audio circuit coming out the speakers. (It doesn't have any speakers.) It isn't my mouse (e.g., when I'm trying to make graphics ops happen); the sound happens if I set up a recurring operation and don't use the mouse at all, or if I lift the mouse off the table slightly (but enough that the laser still registers movement). It isn't the voices in my head; they never whisper like that. Other observations: It doesn't seem to matter what the graphics operation is; anything that changes what's on the screen seems to do it. I get the sound when moving the mouse over the Chromium tab bar (which makes the tab backgrounds change); I get it when a web page has a counter on it that changes the text on the page: I get it when dragging window contents around. The sound is very, very slightly louder if the graphics op is larger, like scrolling a text area when writing a question on superuser.com, than for smaller operations like the tick counter on the web page. But it's very slight. It's fairly loud (and of good duration) when the op involves color changes to substantial surface areas. For instance, when asking a question here on superuser and you move the cursor between the question box and the tag box, and the help to the right fades out, changes, and fades back in. (Yet another example related to the web browser, so let me say: I hear it when operations completely unrelated to the web browser as well.) It doesn't sound like arcing or anything like that (I'd've shut off the machine Right Quick Like if it did). Moving windows does it. Scrolling windows (by and large) doesn't. I have the feeling I've heard this sort of thing before, when all system fans were on low and such, with other systems — but (again) written it off as observational error. For all the world it's like I'm hearing the CPU working (as opposed to the GPU; note the window scroll thing above) or data being transferred somewhere, but that just seems...unlikely. So what am I hearing? This may seem like a very localized question, but perhaps other silent PC enthusiasts may be interested as well...

  Read the article

• Why do we need different CPU architecture for server & mini/mainframe & mixed-core?

  - by claws

  Hello, I was just wondering what other CPU architectures are available other than INTEL & AMD. So, found List of CPU architectures on Wikipedia. It categorizes notable CPU architectures into following categories. Embedded CPU architectures Microcomputer CPU architectures Workstation/Server CPU architectures Mini/Mainframe CPU architectures Mixed core CPU architectures I was analyzing the purposes and have few doubts. I taking Microcomputer CPU (PC) architecture as reference and comparing others. Embedded CPU architecture: They are a completely new world. Embedded systems are small & do very specific task mostly real time & low power consuming so we do not need so many & such wide registers available in a microcomputer CPU (typical PC). In other words we do need a new small & tiny architecture. Hence new architecture & new instruction RISC. The above point also clarifies why do we need a separate operating system (RTOS). Workstation/Server CPU architectures I don't know what is a workstation. Someone clarify regarding the workstation. As of the server. It is dedicated to run a specific software (server software like httpd, mysql etc.). Even if other processes run we need to give server process priority therefore there is a need for new scheduling scheme and thus we need operating system different than general purpose one. If you have any more points for the need of server OS please mention. But I don't get why do we need a new CPU Architecture. Why cant Microcomputer CPU architecture do the job. Can someone please clarify? Mini/Mainframe CPU architectures Again I don't know what are these & what miniframes or mainframes used for? I just know they are very big and occupy complete floor. But I never read about some real world problems they are trying to solve. If any one working on one of these. Share your knowledge. Can some one clarify its purpose & why is it that microcomputer CPU archicture not suitable for it? Is there a new kind of operating system for this too? Why? Mixed core CPU architectures Never heard of these. If possible please keep your answer in this format: XYZ CPU architectures Purpose of XYZ Need for a new architecture. why can't current microcomputer CPU architecture work? They go upto 3GHZ & have upto 8 cores. Need for a new Operating System Why do we need a new kind of operating system for this kind of archictures?

  Read the article

• Kickstart based installation of RHEL 6.4 from USB

  - by Peter

  I want to setup some brand new servers with RHEL 6.4. Servers do not have DVD, so, I have to use USB for the installation. I already have a custom ISO with a kickstart file that I use on servers with DVD flawlessly. I used iso2usb to move the ISO t? my USB. When I boot from the USB, the ks file is found, anaconda starts, but then stops with the following error: "The installation source given by device ['sda1'] could not be found. Please check your parameters and try again" Notes: The USB IS the sda. My custom ISO file is renamed to linux.iso from iso2usb and it is present in the root directory of the USB. Kickstart file has the following entry: harddrive --partition=sda1 --dir=/ Please help me to automate the installation with kickstart. Edit 1: This the anaconda.log file: 09:01:57,029 INFO : no /etc/zfcp.conf; not configuring zfcp 09:01:57,259 INFO : created new libuser.conf at /tmp/libuser.4rAbps with instPath="/mnt/sysimage" 09:01:57,259 INFO : anaconda called with cmdline = ['/usr/bin/anaconda', '--stage2', 'hd:sda1:///images/install.img', '--dlabel', '--kickstart', '/tmp/ks.cfg', '--graphical', '--selinux', '--lang', 'en_US.UTF-8', '--keymap', 'us', '--repo', 'hd:sda1:/'] 09:01:57,260 INFO : Display mode = g 09:01:57,260 INFO : Default encoding = utf-8 09:01:59,444 DEBUG : X server has signalled a successful start. 09:01:59,446 INFO : Starting window manager, pid 1345. 09:01:59,537 INFO : Starting graphical installation. 09:01:59,741 INFO : Detected 7968M of memory 09:01:59,741 INFO : Swap attempt of 7968M 09:02:00,840 INFO : ISCSID is /usr/sbin/iscsid 09:02:00,840 INFO : no initiator set Edit 2: This is the part of anaconda log that indicates that it found the USB etc: 09:01:47,918 INFO : starting STEP_STAGE2 09:01:47,918 INFO : partition is sda1, dir is //images/install.img 09:01:47,918 INFO : mounting device sda1 for hard drive install 09:01:48,005 INFO : Path to stage2 image is /mnt/isodir///images/install.img 09:01:54,214 INFO : mounted loopback device /mnt/runtime on /dev/loop0 as /tmp/install.img 09:01:54,214 INFO : Looking for updates for HD in /mnt/isodir///images/updates.img 09:01:54,214 INFO : Looking for product for HD in /mnt/isodir///images/product.img 09:01:54,227 INFO : got stage2 at url hd:sda1:///images/install.img 09:01:54,254 INFO : Loading SELinux policy 09:01:54,700 INFO : getting ready to spawn shell now 09:01:54,975 INFO : Running anaconda script /usr/bin/anaconda 09:01:56,882 INFO : _Fedora is the highest priority installclass, using it 09:01:56,921 INFO : Running kickstart %%pre script(s) 09:01:56,922 WARNING : '/bin/sh' specified as full path 09:01:56,926 INFO : All kickstart %%pre script(s) have been run

  Read the article

• Secret, unlogged, transparent, case-sensitive proxy in IIS6?

  - by Ian Boyd

  Does IIS have a secret, unlogged, transparent, case-sensitive proxy built into it? A file exists on the web-server: GET http://www.stackoverflow.com/javascript/ModifyQuoteArea.js HTTP/1.1 Accept: text/html, application/xhtml+xml, */* Accept-Language: en-US User-Agent: Mozilla/5.0 (compatible; MSIE 9.0; Windows NT 6.1; WOW64; Trident/5.0) Accept-Encoding: gzip, deflate Connection: Keep-Alive Host: www.stackoverflow.com HTTP/1.1 200 OK Connection: Keep-Alive Content-Length: 29246 Date: Mon, 07 Mar 2011 14:20:07 GMT Content-Type: application/x-javascript ETag: "5a0a6178edacb1:1c51" Server: Microsoft-IIS/6.0 Last-Modified: Fri, 02 Tue 2010 17:03:32 GMT Accept-Ranges: bytes X-Powered-By: ASP.NET ... Problem is that a changes made to the file will not get served, the old (i.e. February of last year) version keeps getting served: HTTP/1.1 200 OK Connection: Keep-Alive Content-Length: 29246 Date: Mon, 07 Mar 2011 14:23:07 GMT Content-Type: application/x-javascript ETag: "5a0a6178edacb1:1c51" Server: Microsoft-IIS/6.0 Last-Modified: Fri, 02 Tue 2010 17:03:32 GMT Accept-Ranges: bytes X-Powered-By: ASP.NET ... The same old file gets served, even though we've: renamed the file deleted the file restarted IIS The request for this file does not appear in the IIS logs (e.g. C:\WINNT\System32\LogFiles\W3SVC7\) And this only happens from the outside (i.e. the internet). If you issue the request locally on the server, then you will: - get the current file (file there) - 404 (file renamed) - 404 (file deleted) But if i change the case of the requested resource, i.e.: GET http://www.stackoverflow.com/javascript/MoDiFyQuOtEArEa.js HTTP/1.1 Accept: text/html, application/xhtml+xml, */* Accept-Language: en-US User-Agent: Mozilla/5.0 (compatible; MSIE 9.0; Windows NT 6.1; WOW64; Trident/5.0) Accept-Encoding: gzip, deflate Connection: Keep-Alive Host: www.stackoverflow.com Note: MoDiFyQuOtEArEa.js verses ModifyQuoteArea.js Then i do get the proper file (or get the 404 as i expect if the file is renamed or deleted). But any subsequent changes to the file will not show up until i change the case of the file i'm asking for. Checking the IIS logs all indicate that the (internet) requests are all coming the correct client on the internet (i.e. not from some intermediate proxy). Since the file doesn't exist on the hard drive anymore, i conclude that there is a proxy. The requests serviced from this proxy are not logged in the IIS logs. The requests for new files are logged, and from the client IP, not a proxy IP. The proxy is case sensitivie. This does not sound like something Microsoft, or IIS, would do: - a transparent proxy - case-sensitivie - unlogged - surviving restarts of IIS - surviving in a cache for hours i can't believe that our customer's IIS is doing these things. i'm assuming there is some other transparent proxy in front of IIS. Or, does IIS have a transparent, unlogged, case-sensitive, memory based, proxy, that caches content for at least 7 hours? (Come Monday morning, IIS is serving the correct file, unlogged).

  Read the article

• RHEL 6.x on Rackspace Cloud and Dedicated hardware experiencing Redis Timeouts

  - by zhallett

  I just recently set up a mixture of RHEL 6.1 Rackspace cloud hosts and RHEL 6.2 dedicated hosts using Rackconnect. I am experiencing intermittent Redis timeouts from within our Rails 3.2.8 app with Redis 2.4.16 running on the RHEL 6.2 dedicated hosts. There is no network latency or packet loss. Also there are no errors on any interfaces on our cloud or dedicated servers or on the managed firewall from Rackspace. When Redis timesout, there is nothing logged within redis even though it is set up to do debug logging. The only error we receive is from Airbrake saying there was a Redis timeout. Network topology: RHEL 6.1 cloud hosts <--> Alert logic IDS <--> Cisco ASA 5510 <--> RHEL 6.2 dedicated hosts (web nodes) (two way NAT) (db hosts running redis) Ping from db host to web host: 64 bytes from 10.181.230.180: icmp_seq=998 ttl=64 time=0.520 ms 64 bytes from 10.181.230.180: icmp_seq=999 ttl=64 time=0.579 ms 64 bytes from 10.181.230.180: icmp_seq=1000 ttl=64 time=0.482 ms --- web1.xxxxxx.com ping statistics --- 1000 packets transmitted, 1000 received, 0% packet loss, time 999007ms rtt min/avg/max/mdev = 0.359/0.535/5.684/0.200 ms Ping from web host to db host: 64 bytes from 192.168.100.26: icmp_seq=998 ttl=64 time=0.544 ms 64 bytes from 192.168.100.26: icmp_seq=999 ttl=64 time=0.452 ms 64 bytes from 192.168.100.26: icmp_seq=1000 ttl=64 time=0.529 ms --- data1.xxxxxx.com ping statistics --- 1000 packets transmitted, 1000 received, 0% packet loss, time 999017ms rtt min/avg/max/mdev = 0.358/0.499/6.120/0.201 ms Redis config: daemonize yes pidfile /var/run/redis/6379/redis_6379.pid port 6379 timeout 0 loglevel debug logfile /var/lib/redis/log syslog-enabled yes syslog-ident redis-6379 syslog-facility local0 databases 16 save 900 1 save 300 10 save 60 10000 rdbcompression yes dbfilename dump-6379.rdb dir /var/lib/redis maxclients 10000 maxmemory-policy volatile-lru maxmemory-samples 3 appendfilename appendonly-6379.aof appendfsync everysec no-appendfsync-on-rewrite no auto-aof-rewrite-percentage 100 auto-aof-rewrite-min-size 64mb slowlog-log-slower-than 10000 slowlog-max-len 1024 vm-enabled no vm-swap-file /tmp/redis.swap vm-max-memory 0 vm-page-size 32 vm-pages 134217728 vm-max-threads 4 hash-max-zipmap-entries 512 hash-max-zipmap-value 64 list-max-ziplist-entries 512 list-max-ziplist-value 64 set-max-intset-entries 512 zset-max-ziplist-entries 128 zset-max-ziplist-value 64 activerehashing yes Redis-cli info: redis-cli info redis_version:2.4.16 redis_git_sha1:00000000 redis_git_dirty:0 arch_bits:64 multiplexing_api:epoll gcc_version:4.4.6 process_id:4174 uptime_in_seconds:79346 uptime_in_days:0 lru_clock:1064644 used_cpu_sys:13.08 used_cpu_user:19.81 used_cpu_sys_children:1.56 used_cpu_user_children:7.69 connected_clients:167 connected_slaves:0 client_longest_output_list:0 client_biggest_input_buf:0 blocked_clients:6 used_memory:15060312 used_memory_human:14.36M used_memory_rss:22061056 used_memory_peak:15265928 used_memory_peak_human:14.56M mem_fragmentation_ratio:1.46 mem_allocator:jemalloc-3.0.0 loading:0 aof_enabled:0 changes_since_last_save:166 bgsave_in_progress:0 last_save_time:1352823542 bgrewriteaof_in_progress:0 total_connections_received:286 total_commands_processed:507254 expired_keys:0 evicted_keys:0 keyspace_hits:1509 keyspace_misses:65167 pubsub_channels:0 pubsub_patterns:0 latest_fork_usec:690 vm_enabled:0 role:master db0:keys=6,expires=0 edit 1: add redis-cli info output

  Read the article

• Starting MySQL database server: mysqld . . . . . . . . . . . . . . failed!

  - by meder

  I restarted my VPS box ( manually/hard restart ) and ever since, mysql fails to start for whatever reason. I did a tail /var/log/syslog and I get this: Feb 20 11:49:33 kyrgyznews mysqld[11461]: ) ;InnoDB: End of page dump 575 Feb 20 11:49:33 kyrgyznews mysqld[11461]: 110220 11:49:33 InnoDB: Page checksum 1045788239, prior-to-4.0.14-form checksum 236985105 576 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: stored checksum 1178062585, prior-to-4.0.14-form stored checksum 236985105 577 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Page lsn 0 10651, low 4 bytes of lsn at page end 10651 578 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Page number (if stored to page already) 3, 579 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: space id (if created with >= MySQL-4.1.1 and stored already) 0 580 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Database page corruption on disk or a failed 581 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: file read of page 3. 582 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: You may have to recover from a backup. 583 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: It is also possible that your operating 584 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: system has corrupted its own file cache 585 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: and rebooting your computer removes the 586 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: error. 587 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: If the corrupt page is an index page 588 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: you can also try to fix the corruption 589 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: by dumping, dropping, and reimporting 590 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: the corrupt table. You can use CHECK 591 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: TABLE to scan your table for corruption. 592 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: See also InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html 593 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: about forcing recovery. 594 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Ending processing because of a corrupt database page. 595 Feb 20 11:49:33 kyrgyznews mysqld_safe[11469]: ended 596 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: 0 processes alive and '/usr/bin/mysqladmin --defaults-file=/etc/mysql/debian.cnf ping' resulted in 597 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: ^G/usr/bin/mysqladmin: connect to server at 'localhost' failed 598 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: error: 'Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2)' 599 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: Check that mysqld is running and that the socket: '/var/run/mysqld/mysqld.sock' exists! 600 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: 601 Feb 20 11:49:56 kyrgyznews mysqld_safe[13437]: started 602 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: The log sequence number in ibdata files does not match 603 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: the log sequence number in the ib_logfiles! 604 Feb 20 11:49:56 kyrgyznews mysqld[13440]: 110220 11:49:56 InnoDB: Database was not shut down normally! 605 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Starting crash recovery. 606 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Reading tablespace information from the .ibd files... 607 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Restoring possible half-written data pages from the doublewrite 608 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: buffer... 609 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Database page corruption on disk or a failed 610 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: file read of page 3. 611 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: You may have to recover from a backup. I have looked at the page it referenced, http://dev.mysql.com/doc/refman/5.0/en/forcing-innodb-recovery.html, but before messing with any settings I was wondering what experienced DBAs would suggest doing? Is there any harm in forcing the recovery? PS - I did not make any updates to mysql. Version is mysql Ver 14.12 Distrib 5.0.51a, for debian-linux-gnu (i486) using readline 5.2.

  Read the article

• Performance issues when using SSD for a developer notebook (WAMP/LAMP stack)?

  - by András Szepesházi

  I'm a web application developer using my notebook as a standalone development environment (WAMP stack). I just switched from a Core2-duo Vista 32 bit notebook with 2Gb RAM and SATA HDD, to an i5-2520M Win7 64 bit with 4Gb RAM and 128 GB SDD (Corsair P3 128). My initial experience was what I expected, fast boot, quick load of all the applications (Eclipse takes now 5 seconds as opposed to 30s on my old notebook), overall great experience. Then I started to build up my development stack, both as LAMP (using VirtualBox with a debian guest) and WAMP (windows native apache + mysql + php). I wanted to compare those two. This still all worked great out, then I started to pull in my projects to these stacks. And here came the nasty surprise, one of those projects produced a lot worse response times than on my old notebook (that was true for both the VirtualBox and WAMP stack). Apache, php and mysql configurations were practically identical in all environments. I started to do a lot of benchmarking and profiling, and here is what I've found: All general benchmarks (Performance Test 7.0, HDTune Pro, wPrime2 and some more) gave a big advantage to the new notebook. Nothing surprising here. Disc specific tests showed that read/write operations peaked around 380M/160M for the SSD, and all the different sized block operations also performed very well. Started apache performance benchmarking with Apache Benchmark for a small static html file (10 concurrent threads, 500 iterations). Old notebook: min 47ms, median 111ms, max 156ms New WAMP stack: min 71ms, median 135ms, max 296ms New LAMP stack (in VirtualBox): min 6ms, median 46ms, max 175ms Right here I don't get why the native WAMP stack performed so bad, but at least the LAMP environment brought the expected speed. Apache performance measurement for non-cached php content. The php runs a loop of 1000 and generates sha1(uniqid()) inisde. Again, 10 concurrent threads, 500 iterations were used for the benchmark. Old notebook: min 0ms, median 39ms, max 218ms New WAMP stack: min 20ms, median 61ms, max 186ms New LAMP stack (in VirtualBox): min 124ms, median 704ms, max 2463ms What the hell? The new LAMP performed miserably, and even the new native WAMP was outperformed by the old notebook. php + mysql test. The test consists of connecting to a database and reading a single record form a table using INNER JOIN on 3 more (indexed) tables, repeated 100 times within a loop. Databases were identical. 10 concurrent threads, 100 iterations were used for the benchmark. Old notebook: min 1201ms, median 1734ms, max 3728ms New WAMP stack: min 367ms, median 675ms, max 1893ms New LAMP stack (in VirtualBox): min 1410ms, median 3659ms, max 5045ms And the same test with concurrency set to 1 (instead of 10): Old notebook: min 1201ms, median 1261ms, max 1357ms New WAMP stack: min 399ms, median 483ms, max 539ms New LAMP stack (in VirtualBox): min 285ms, median 348ms, max 444ms Strictly for my purposes, as I'm using a self contained development environment (= low concurrency) I could be satisfied with the second test's result. Though I have no idea why the VirtualBox environment performed so bad with higher concurrency. Finally I performed a test of including many php files. The application that I mentioned at the beginning, the one that was performing so bad, has a heavy bootstrap, loads hundreds of small library and configuration files while initializing. So this test does nothing else just includes about 100 files. Concurrency set to 1, 100 iterations: Old notebook: min 140ms, median 168ms, max 406ms New WAMP stack: min 434ms, median 488ms, max 604ms New LAMP stack (in VirtualBox): min 413ms, median 1040ms, max 1921ms Even if I consider that VirtualBox reached those files via shared folders, and that slows things down a bit, I still don't see how could the old notebook outperform so heavily both new configurations. And I think this is the real root of the slow performance, as the application uses even more includes, and the whole bootstrap will occur several times within a page request (for each ajax call, for example). To sum it up, here I am with a brand new high-performance notebook that loads the same page in 20 seconds, that my old notebook can do in 5-7 seconds. Needless to say, I'm not a very happy person right now. Why do you think I experience these poor performance values? What are my options to remedy this situation?

  Read the article

• CPU Lockup when loading folder of bookmarks in Firefox

  - by Gary M. Mugford

  I am running Firefox 3.6 on WinXPSP3 on a duo Core machine with 4G of memory. I am also running Avast! free anti-virus and ZoneAlarm free firewall, both latest versions. Within the last month, my service provider basically forced me to upgrade to a Docsis 3.0 compliant modem (offered me a deal I couldn't turn down). At that point, I also upgraded to FF3.6. Basically, I am not unhappy with many aspects of this switchover, EXCEPT, when I now load a folder of bookmarks (anywhere from 10 to 38) I get nothing like the load times I experienced a couple of months back. It's taking minutes rather than seconds. And the first bookmark in one of the folders, GMail, rarely loads before timing out. I have used the old trick of powering off the cable modem before my day's work. This used to fix 'load-lag' in the old days. I have switched from my ISP's DNS server to Google, OpenDNS and back. And nothing seems to work currently. It's not my DNS cache. That's been flushed and secondary computers also have the same issue when loading folders. I have watched the CPU usage and loading the folder will send VSMon (ZoneAlarm) usage over 40 percent, AVastSvc (Avast!) over 30 and Firefox will then push the needle to 100. There's a brief burst by SVCHost when the others falter in devouring cycles. Then everything subsides to single digits once the last tab is loaded. The only other nominal nastiness is VSMon ALWAYS hitting 50 percent when ANY program starts downloading content from the internet. If I shutdown ZoneAlarm (and VSMon with it), the same slow loading takes place, but this time System is running 50% plus, again driving the usage to 100 per cent. I have my doubts FF3.6 vs FF3.5 is an issue, since the other computers are still running 3.5 and suffer the same issue. Those computers are on, but inactive, most of the time, being backups. Obviously, when the CPU hits 100, I can't do much of anything in FireFox OR in other programs. Video play through WMPC or VLC is extremely choppy, although it doesn't seem to affect the audio. Any ideas what I can try next? Thanks, GM

  Read the article

• Crashes and freezes after fixing "BOOTMGR is missing" error

  - by Greg-J

  I came back from a 3-day weekend to a computer that was off. I leave my PC on 24/7, so this was odd. Turn it on to get the dreaded "BOOTMGR is missing" screen. Two attempts at Windows Recovery and it booted into Windows fine. After an hour or so, I get a frozen Chrome and my start bar disappears. Ctrl+Alt+Del brings up an error box telling me that Ctrl+Alt+Del failed to work properly. Clicking on any open application triggers an error (I can't recall the error now, but it essentially just said that the application couldn't be found running or something along those lines). I restart, and again, the same thing happens after a while of use. I turn it on, install the 47 updates I have or so, and then restart it. After a while of use (under an hour), it just freezes completely. My thoughts are: SSDs, RAM or PS. My system specs below: (RAID0) 2 x Crucial M4 CT128M4SSD2 2.5" 128GB SATA III MLC Internal Solid State Drive (SSD) CORSAIR Vengeance 16GB (4 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Desktop Memory Model CML16GX3M4A1600C9 CORSAIR HX Series HX750 750W ATX12V 2.3 / EPS12V 2.91 SLI Ready CrossFire Ready 80 PLUS GOLD Certified Modular Active 1 x ASUS Maximus IV Gene-Z/GEN3 LGA 1155 Intel Z68 HDMI SATA 6Gb/s USB 3.0 Micro ATX Intel Motherboard 1 x Hitachi GST Deskstar 7K1000.C 0F10383 1TB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive 1 x Intel Core i7-2600K Sandy Bridge 3.4GHz (3.8GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 1 x SAPPHIRE 21197-00-40G Radeon HD 7970 3GB 384-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card 1 x Noctua NH-D14 120mm & 140mm SSO CPU Cooler This is all crammed in a pretty small case (NZXT Vulcan) and has been running perfectly problem-free since January. The only thing out of the ordinary is that there is a fan in the case that is now making noise whereas the case has previously been completely silent. I have no reason to believe this is anything more then correlation, but felt it is worth mentioning. I believe it MAY be the SSDs simply because of the BOOTMGR error, but not sure how to test that theory. My belief that it may be the RAM is simply from experience with frozen machines. I haven't had the time to memtest it, but will. The PS being the culprit is something I've picked up by reading similar threads on various forums, and it seems plausible. I am unsure how to test this though. ANY insight whatsover would be greatly appreciated!

  Read the article

• IP Micro-outages, telephone micro-outages, and CATV micro-outages

  - by Michael Graff

  This is a long and complicated question, mostly because it has been going on for 2.5 years without a solution in sight. It also is only one-third computer related, the other two-thirds are cable TV and cable-phone related. Background I have COX Communications for a cable provider, and we get Internet, digital cable TV, and digital phone service through them. The Internet is a SB5101 right now, and has been a DPC2100 and SB5120 in the past. Same results. The phone service is provided through a telephone interface mounted on the outside of the house (not classic VoIP) and the CATV is through a Scientific Atlanta receiver without DVR. I do have a TiVo connected to the CATV box. Symptoms The CATV shows "blocking" -- sometimes very very short duration where a few blocks appear on the screen. Sometimes it lasts long enough that the video "pauses" for 2-5 seconds, and rarely but not unseen the audio also fails. The CATV decoder box shows no correctable (FEC) or uncorrectable errors. That is, all BER counters are zero for the video stream. The Internet shows "micro-outages" where it appears that sent packets are not making it out, but I continue to receive packets from local modems. That is, pings stop coming back, but I continue to see modems broadcast for DHCP, and sometimes they ask more than once. The cable modem shows no errors during this time, but cable modems lie like you would not believe. It is actually possible to unplug the coax from the modem for 20 seconds and it reports NO ERRORS to the provider's tools. The phone service cuts out for 1-3 seconds, infrequently. When this happens, I hear NOTHING (not even comfort noise) and the remote side hears a "click" as if I were getting a call waiting message. However, there is no call incoming, other than the one I'm currently on of course. Things SEEM to happen more frequently when the temperature outside swings from cold to warm, so fall/spring seems worse than summer/winter. All micro-outages occur between once or twice a day (which I could ignore) to 10 times per hour. All SNR, signal levels, noise levels, etc. show very close to optimal when measured. COX's diagnosis This is a continual pain for me. Over the last 2.5 years, they have opened, "fixed" something, and closed the tickets. They close it without confirming that it is indeed better, and when I reopen they cannot do that, but instead they open a new ticket and send yet another low-level tech out to do the same signal tests and report that all is OK. I've finally gotten a line tech who has a clue and is motivated enough to pursue this with me. We have tried things like switching the local nodes over to UPS and generator power, but this does not trigger the noise. We have tried replacing all cabling, the tap outside my house, the modem, the CATV decoder -- all without resolution. Recently they have decided it is both my computer or switch, my TiVo, and my phone that are all broken and causing this issue. My debugging steps I spent the worse day of my TV-watching life yesterday and part of today. I watched live TV without the TiVo. I witnessed blocking, but it did "feel different." and was actually more severe. Some days it is better, some days it is worse, so perhaps this was just a very bad day. Today, I connected the TiVo to my DVD player, and ran two very long movies through it. I saw no blocking at all during nearly 6 hours of video. Suggestions? Does anyone have any suggestions on what to do next? I understand perhaps only the IP side can be addressed here, but it is one of the more limiting debugging options.

  Read the article

• Windows XP installation problems

  - by Samurai Waffle

  I recently asked a question on here, and thought I had it working... Here is a link to it. Windows XP Installation problems So basically I'm having trouble getting XP installed. To sum it up, a computer I have had a boot sector virus, and I used Darik's Nuke and Boot to wipe the hard drive clean. So the hard drive has nothing on it. I had to try and install Windows through a DOS prompt, because for some reason it won't read it off the DVD. The UBCD is able to look at the files located on the DVD I have in, but I can't boot from it for some reason. So I extracted it to a USB drive, booted to DOS and started the setup process. Here's the weird thing with DOS... It can only find the C: drive. The C: drive in DOS is the flash drive that I have in, running DOS. I can't find the hard drive anywhere! So anyways, after starting the setup process, it copied the files over to the "hard drive" (which took 16 hours because the version of DOS I ran couldn't run smartdrv.exe), and it said the computer had to reboot. So I let it reboot, and it stopped and said there is no boot device. So I popped in UBCD that I have installed on a flash drive, and I discovered that it had copied the Windows files over to the flash drive and not the hard drive. It never asked where it should extract the files... So I toyed around with UBCD, ran a memory test on the hard drive to make sure it was fine, and it came out clean. So I'm stuck now. How can I get this installed? Writing this, I came up with an idea. If I copy the DOS startup files over to the hard drive, would I be able to start DOS from it? If so, I believe that could fix my problems. Any help is greatly appreciated, because I am running out of ideas and am at my wits end with this computer.

  Read the article

• Resizing Partitions on Live RHEL/cPanel Server

  - by Timothy R. Butler

  I've resized many partitions over the years on Linux, Windows and Mac OS X -- but always using a GUI. However, the time has come where the preset partition sizes my data center placed on my server aren't the right sizes and I need to resize a production server's disks. I could fiddle with it and probably do OK, but given that it is a production server, I wanted to get some advice about the right way to do this. I do have KVM over IP access, so if it is best to take the server offline and boot off a rescue partition, I can do that. root [/var/lib/mysql]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.9G 2.1G 7.3G 23% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 99M 77M 18M 82% /boot /dev/sda8 884G 463G 376G 56% /home /dev/sda3 9.9G 8.0G 1.5G 85% /usr /dev/sda5 9.9G 9.1G 308M 97% /var /usr/tmpDSK 2.0G 38M 1.8G 3% /tmp As you can see /var and /usr are quite close to being full and I've actually had to symlink some logs on /usr to directories in /home to balance things out. What I would like to do is to add 6-10 GB each to /usr and /var, presumably taking the space from /home. As I think about how the disk is arranged, the best thought I've come up with is to reduce /home by 16 GB, say, and move /var to the spot freed up, then allocating /var's space to /usr. However, that would put /var at the far end of the disk, which seems less than idea, given that MySQL has all of its data on that partition. I'd love to take the space out of the closer end of /usr, but I assume that would take a very arduous (and perhaps risky) process of moving all of the data in /usr around. I seem to recall having such a process fail for me on a computer in the past. The other option might be to merge / and /usr since / is underutilized, though I'm not sure if that's a good idea. Do you have any suggestions both on the best reallocation plan and the commands to use to accomplish it? UPDATE: I should add -- here's the partition table. There's one unused partition, which, if memory serves, was the original tmp location before I created a tmp image: Name Flags Part Type FS Type [Label] Size (MB) ------------------------------------------------------------------------------ Unusable 1.05* sda1 Boot Primary Linux ext2 106.96* sda2 Primary Linux ext3 10737.42* sda3 Primary Linux ext3 10737.42* sda5 NC Logical Linux ext3 10738.47* sda6 NC Logical Linux swap / Solaris 2148.54* sda7 NC Logical Linux ext3 1074.80* sda8 NC Logical Linux ext3 964098.53*

  Read the article

• Where should I go with hosting my site: VPS, GAE, another option?

  - by Jonathan Hayward

  My website, http://JonathansCorner.com/, began life before 1994 as www.imsa.edu/~jhayward/ and has been through various iterations and improvements to content, HTML, and the like, but remains a literature site that is from a web administrator's perspective fairly simple and primitive: a fair amount of static HTML and supporting files, a little bit of CGI and URI rewriting, .htaccess files providing Expires: headers and the like. An associated site demoes various CGI scripts that fall under the category of "and other creations"; the site as a whole has the purpose of sharing my creative works, and so far a fairly rudimentary use of Apache functionality, supported by Unix tools to, for instance, update RSS feed and the "starting point" link on the home page, has served that purpose fairly well. I looked around here on web hosting, and found the note on web host reccommendations as a good note for "What are some of people's favorite web hosts overall," but I wanted to ask a more focused question of "What are the best web hosts for criteria XYZ:" I am looking at a VPS so I will have root, be able to install stuff and edit Apache's config files etc., running Gentoo or other Linux, BSD, or the like. I would like a system that is secure enough that the host's vulnerabilities are mostly the ones that come along with what I am trying to do: that is, I won't be trying to administer and secure an ancient Linux like some have complained about at 1and1. I would like good uptime/reliability and competent support staff: if the level 1 help desk is going to tell me to go to "My Computer" on a Linux box, I'd like to be able to get past them. Ideally I would like a site hosted within some place that will have low latency for U.S. visitors in particular. I would like a hosting solution that will be with a stable business, one that will probably be around, and one unlikely to vanish without warning. With those things specified, I would be interested in knowing what are the less expensive options. (I expect that some of the things I've specified will knock out all of the cheapest options, but I'm still interested in price.) With all that stated, I'd like to back up a bit and look at whether I am asking the right question. I am concerned that the above is a very good way of asking, "How can I keep my site in line with the wave of the past?" I am wondering if it might be specifically wiser to look to adapt my site to newer technologies instead of trying to keep it on older technologies. For instance, while I would hardly portray my site as a way to show off the full power of Google App Engine, the main site at least should be a straightforward port if I were to do that. And beyond Google App Engine, my knowledge of cloud solutions is basic. If it is a better and more future-proof solution to port my site to another kind of solution, I would be interested in knowing where those future-proof solutions lie. So I would be interested in wisdom. If the question I asked in detail is still a good question to be asking, what would people suggest? Or if I should seriously consider porting my site to a newer basic option, what should I try there? Any thoughts would be appreciated.

  Read the article

• CPU overheating after cleaning it

  - by Roberts

  I wanted to clean my computer CPU heatsink and fan itself, because the temperature is not what I wanted. About (50C ~ 70C). I have Intel Core 2 Duo E4300 @1.8 GHz (LGA775). The heatsink wasn't so scary filled with dust but I wanted to clean it anyway. I didn't know how to get heatsink with fan from the socket. So after 25 minutes I've figured it out. But I didn't know how to get it back on so I spent a lot time getting out the motherboard from the case. The fan and heatsink... The case and all components are clear of dust. (I'm tired now). Then I put all back just the way it was, well did few things on cable management. But the problem was that I didn't know how to connect front audio connectors. I had Windows XP hibernated. So I started the PC and everything was normal, except CMOS memory was clear. I configured the BIOS just the way it was and while I was doing that I saw about 58C CPU temperature and fan at 1789 RPM. Restarted the computer with new settings applied. But Windows halted with Blue Screen (I forgot what error it was but something with KERNEL). Restarted the PC and deleted hibernation session and everything was back normal. But couldn't record any sound from front panel microphone. The problem was that I messed ground wire with mic. Again after fixing it I turned computer on. No problems. The fan currently is noisy and temperature was 78C. The temperature before was 55C - 60C at idle. Now it's about 60C. If I do something then temperature raises to 79C. While speaking in skype the temperature was 82C. Could this problem occur because of the thermal grease (it's old and never replaced)? Edit The problem wasn't in thermal paste (because I didn't touch it). The problem was that I installed heatsink wrong. Now instead of regular 60C CPU temperature the CPU is at 48C (cool).

  Read the article

• Command-line video editing in Linux (cut, join and preview)

  - by sdaau

  I have rather simple editing needs - I need to cut up some videos, maybe insert some PNGs in between them, and join these videos (don't need transitions, effects, etc.). Basically, pitivi would do what I want - except, I use 640x480 30 fps AVI's from a camera, and as soon as I put in over a couple of minutes of that kind of material, pitivi starts freezing on preview, and thus becomes unusable. So, I started looking for a command line tool for Linux; I guess only ffmpeg (command line - Using ffmpeg to cut up video - Super User) and mplayer (Sam - Edit video file with mencoder under linux) are so far candidates, but I cannot find examples of the use I have in mind.   Basically, I'd imagine there's an encoder and player tools (like ffmpeg vs ffplay; or mencoder vs mplayer) - such that, to begin with, the edit sequence could be specified directly on the command line, preferably with frame resolution - a pseudocode would look like: videnctool -compose --file=vid1.avi --start=00:00:30:12 --end=00:01:45:00 --file=vid2.avi --start=00:05:00:00 --end=00:07:12:25 --file=mypicture.png --duration=00:00:02:00 --file=vid3.avi --start=00:02:00:00 --end=00:02:45:10 --output=editedvid.avi ... or, it could have a "playlist" text file, like: vid1.avi 00:00:30:12 00:01:45:00 vid2.avi 00:05:00:00 00:07:12:25 mypicture.png - 00:00:02:00 vid3.avi 00:02:00:00 00:02:45:10 ... so it could be called with videnctool -compose --playlist=playlist.txt --output=editedvid.avi The idea here would be that all of the videos are in the same format - allowing the tool to avoid transcoding, and just do a "raw copy" instead (as in mencoder's copy codec: "-oac copy -ovc copy") - or in lack of that, uncompressed audio/video would be OK (although it would eat a bit of space). In the case of the still image, the tool would use the encoding set by the video files.   The thing is, I can so far see that mencoder and ffmpeg can operate on individual files; e.g. cut a single section from a single file, or join files (mencoder also has Edit Decision Lists (EDL), which can be used to do frame-exact cutting - so you can define multiple cut regions, but it's again attributed to a single file). Which implies I have to work on cutting pieces first from individual files first (each of which would demand own temporary file on disk), and then joining them in a final video file. I would then imagine, that there is a corresponding player tool, which can read the same command line option format / playlist file as the encoding tool - except it will not generate an output file, but instead play the video; e.g. in pseudocode: vidplaytool --playlist=playlist.txt --start=00:01:14 --end=00:03:13 ... and, given there's enough memory, it would generate a low-res video preview in RAM, and play it back in a window, while offering some limited interaction ( like mplayer's keyboard shortcuts for play, pause, rewind, step frame). Of course, I'd imagine the start and end times to refer to the entire playlist, and include any file that may end up in that region in the playlist. Thus, the end result of all this would be: command line operation; no temporary files while doing the editing - and also no temporary files (nor transcoding) when rendering final output... which I myself think would be nice. So, while I think that all of the above may be a bit of a stretch - does there exist anything that would approximate the workflow described above?

  Read the article

• How to enable caching on Apache / Ubuntu Linux?

  - by Jim Mischel

  I have a large (several megabytes) XML file that's updated rather frequently (every 10 minutes or less) and gets a lot of traffic. I'd like to implement some caching to reduce bandwidth and server load. Looking at the Apache documents, I see a dizzying array of configuration options that involve various combinations of mod_expires, mod_headers, and mod_cache (and variants). I end up running in circles and the results aren't what I expect. I'm comfortable editing the various configuration files if I have some idea what I'm supposed to change. But at the moment I'm poking around in the dark and that's never a comfortable feeling. So, perhaps if I describe what I want, somebody here can take me by the hand and say, "This is what you need to do." Periodically, this file, call it "stuff.xml" is updated and a new version copied to the directory. The external url would be, for example, http://example.com/stuff.xml. Understand, this part works. Whenever I request the file, I get the expected result. But the file is big and I want to save bandwidth, so first I'd like to implement conditional GET semantics with the If-Modified-Since header. How do I do this? I've enabled mod_headers and mod_expired and added the <FilesMatching> section in my httpd.conf as recommended in countless examples I've seen online, but that didn't change the behavior when made a conditional GET request. I always get a status 200 with the entire document. So how the heck do I implement this? That'll cut down on neeless transfers. I'd also like to limit the amount of data transferred. Seeing as this is XML, gzipping it should save me 50% or more. My next step would be to somehow gzip the file and, if it's not too difficult, store it in memory. That'll cut down on per-access data transfer, and also reduce disk transfers. So how do I implement this type of caching? Thanks in advance.

  Read the article

• PC runs very slowly for no apparent reason

  - by GalacticCowboy

  I have a Dell Latitude D820 that I've owned for about 2.5 years. It is a Core 2 Duo T7200 2.0GHz, with 2 GB of RAM, an 80 GB hard drive and an NVidia Quadro 120M video card. The computer was purchased in late November of 2006 with XP Pro, and included a free upgrade to Vista Business. (Vista was available on MSDN but not yet via retail, so the Vista Business upgrades weren't shipped until March of '07.) Since we had an MSDN subscription at the time, I installed Vista Ultimate on it pretty much as soon as I got it. It ran happily until sometime in the spring of 2007 when Media Center (which I had never used except to watch DVDs) started throwing some kind of bizarre SQL (CE?) error. This error would pop up at random times just while using the computer. Furthermore, Media Center would no longer start. I never identified the cause of this error. I had the Vista Business upgrade by this time, so I nuked the machine, installed XP and all the drivers, and then the Vista Business upgrade. Again, it ran happily for a few months and then started behaving badly once again. Vista Business doesn't have Media Center, so this exhibited completely unrelated symptoms. For no apparent reason and at fairly random times, the machine would suddenly appear to freeze up or run very slowly. For example, launching a new application window (any app) might take 30-45 seconds to paint fully. However, Task Manager showed very low CPU load, memory, etc. I tried all the normal stuff (chkdsk, defrag, etc.) and ran several diagnostic programs to try to identify any problems, but none found anything. It eventually reached the point that the computer was all but unusable, so I nuked it again and installed XP. This time I decided to stick with XP instead of going to Vista. However, within the past couple of months it has started to exhibit the same symptoms in XP that I used to see in Vista. The computer is still under Dell warranty until December, but so far they aren't any help unless I can identify a specific problem. A friend (partner in a now-dead business) has an identical machine that was purchased at the same time. His machine exhibits none of these symptoms, which leads me to believe it is a hardware issue, but I can't figure out how to identify it. Any ideas? Utilities? Seen something similar? At this point I can't even identify any pattern to the behavior, but would be willing to run a "stress test"-style app for as long as a couple days if I had any hope that it would find something. EDIT July 17 I'm testing jerryjvl's answer regarding the video card, though I'm not sure it fully explains the symptoms yet. This morning I ran a video stress test. The test itself ran fine, but immediately afterward the PC started acting up again. I left ProcExp open and various system processes were consuming 50-60% of the CPU but with no apparent reason. For example, "services.exe" was eating about 40%, but the sum of its child processes wasn't higher than about 5%. I left it alone for several minutes to settle down, and then it was fine again. I used the "video card stability test" from firestone-group.com. Its output isn't very detailed, but it at least exercises the hardware pretty hard. EDIT July 22 Thanks for your excellent suggestions. Here is an update on what I have tried so far. Ran memtest86, SeaTools (Seagate), Hitachi drive fitness test, video card stability test (mentioned above). The video card test was the only one that seemed to produce any results, though it didn't occur during the actual test. I defragged the drive (again...) with JkDefrag I dropped the video card

  Read the article

• Why does NX Client for Windows silently closes after connection?

  - by pavel

  Hey! I connect remotely to my Ubuntu server from Vista machine. Now I need to run a GUI application on the server (Wireshark). So I decided to use FreeNX server/client to view Ubuntu GUI on Vista I have successfully installed FreeNX on Ubuntu and NX Client on Vista. I was following this guide Unfortunately, now I found myself stuck with the following problem. At the client, the !M logo window appears, but after a few seconds that window just closes, even without showing any error message. Guys, I'm really stuck, please help! Maybe I should have installed some graphical environment on the server? These are the details from NX client, it seems there are no errors. ----------------- Info: Display running with pid '7768' and handler '0x670d24'. NXPROXY - Version 3.4.0 Copyright (C) 2001, 2007 NoMachine. See http://www.nomachine.com/ for more information. Info: Proxy running in client mode with pid '2168'. Session: Starting session at 'Sat Dec 19 10:58:35 2009'. Warning: Connected to remote version 3.3.0 with local version 3.4.0. Info: Connection with remote proxy completed. Info: Using WAN link parameters 768/24/1/0. Info: Using cache parameters 4/4096KB/16384KB/16384KB. Info: Using pack method 'adaptive-9' with session 'kde'. Info: Using ZLIB data compression 1/1/32. Info: Using ZLIB stream compression 1/1. Info: No suitable cache file found. Info: Forwarding X11 connections to display ':0'. Info: Listening to font server connections on port '11000'. Session: Session started at 'Sat Dec 19 10:58:35 2009'. Info: Established X server connection. Info: Using shared memory parameters 0/0K. Session: Terminating session at 'Sat Dec 19 10:58:37 2009'. Session: Session terminated at 'Sat Dec 19 10:58:37 2009'. -----------

  Read the article

• Encoding multiple video streams with a single avconv invocation

  - by automatthias

  I played with avconv on Ubuntu and I'm now able to e.g. record the desktop with sound from a soundcard. One thing I wanted to do was recording two video inputs at the same time, for instance the desktop and from the webcam. I thought about doing something like this: avconv \ -f alsa \ -i default \ -acodec flac \ -f video4linux2 \ -r 6 \ -i /dev/video0 \ -f x11grab \ -i :0.0 \ out.mkv My thinking was that if you define multiple video inputs, and the .mkv format can handle multiple video streams, avconv will encode 2 video streams and 1 audio stream into one file. But this isn't what happens: avconv version 0.8.4-6:0.8.4-0ubuntu0.12.10.1, Copyright (c) 2000-2012 the Libav developers built on Nov 6 2012 16:51:11 with gcc 4.7.2 [alsa @ 0x1091bc0] capture with some ALSA plugins, especially dsnoop, may hang. [alsa @ 0x1091bc0] Estimating duration from bitrate, this may be inaccurate Input #0, alsa, from 'default': Duration: N/A, start: 1354364317.020350, bitrate: N/A Stream #0.0: Audio: pcm_s16le, 48000 Hz, 2 channels, s16, 1536 kb/s [video4linux2 @ 0x10923e0] Estimating duration from bitrate, this may be inaccurate Input #1, video4linux2, from '/dev/video0': Duration: N/A, start: 100607.724745, bitrate: 29491 kb/s Stream #1.0: Video: rawvideo, yuyv422, 640x480, 29491 kb/s, 6 tbr, 1000k tbn, 6 tbc [x11grab @ 0x107b2a0] device: :0.0+83,87 -> display: :0.0 x: 83 y: 87 width: 854 height: 480 [x11grab @ 0x107b2a0] shared memory extension found [x11grab @ 0x107b2a0] Estimating duration from bitrate, this may be inaccurate Input #2, x11grab, from ':0.0+83,87': Duration: N/A, start: 1354364318.488382, bitrate: 196761 kb/s Stream #2.0: Video: rawvideo, bgra, 854x480, 196761 kb/s, 15 tbr, 1000k tbn, 15 tbc Incompatible pixel format 'bgra' for codec 'mpeg4', auto-selecting format 'yuv420p' [buffer @ 0x107fcc0] w:854 h:480 pixfmt:bgra [avsink @ 0x10bdf00] auto-inserting filter 'auto-inserted scaler 0' between the filter 'src' and the filter 'out' [scale @ 0x10dc680] w:854 h:480 fmt:bgra -> w:854 h:480 fmt:yuv420p flags:0x4 Output #0, matroska, to '.../out.mkv': Metadata: encoder : Lavf53.21.0 Stream #0.0: Video: mpeg4, yuv420p, 854x480, q=2-31, 4000 kb/s, 1k tbn, 15 tbc Stream #0.1: Audio: libvorbis, 48000 Hz, 2 channels, s16 Stream mapping: Stream #2:0 -> #0:0 (rawvideo -> mpeg4) Stream #0:0 -> #0:1 (pcm_s16le -> libvorbis) Press ctrl-c to stop encoding [mpeg4 @ 0x10bd800] rc buffer underflow ^Cframe= 160 fps= 15 q=2.0 Lsize= 3414kB time=10.66 bitrate=2623.0kbits/s video:3273kB audio:131kB global headers:4kB muxing overhead 0.165600% Received signal 2: terminating. I'm not sure if it's the question of mapping (some -map options to add?) or that avconv just can't encode more than 1 video stream at one time. So is it an actual avconv limitation, or a limitation of the available containers, or me simply not finding the right combination of command line options?

  Read the article

• What presentation software suits my needs?

  - by claws

  Background: I'm teaching biology to 12th grade students. The syllabus I'm teaching is huge. I mean literally, very huge. There is a lot for students to remember. There are no less than 1000 facts (weird names, dates etc) for students to remember. They'll have to remember all of them, they don't have a choice. The notes I compiled for their learning itself is upto 80 printed pages(Just the bullet outline & facts). That's just one chapter. We have 34 chapters. Also my students are very hardworking, they study upto 8-10hrs per day (Yeah! we are from India :). So, I want to ensure maximum retaining by the students at each and every stage (Teaching & Learning). I'm trying to as many memory training techniques as possible. I'm trying to incorporate, mnemonics, strong visual aids (pictures, 3D-animations, real videos etc.), spaced repetition etc. I think MS powerpoint is not suitable for my needs: There are about 200 slides per chapter. Its very easy for students to get lost while teaching. Because the problem with powerpoint is that it gives facts (as bullets) but it doesn't exploit the association & organization (Concept Map) of the content, which helps students learn quickly. I found an amazing software called XMind. You can see the screenshot here. Problem is that it is not as powerpoint in terms of powerpoint. This software can be used for just for concept maps. In the above screenshot, each topic occupies a single slide. I have an Image/picture(Detailed huge picture) and about 5-10 bullet points and probably a video or an animation of somethings. And this XMind is not good at presenting, in terms that it doesn't allow me to set what to present after what. I want to present a top down view, with a slide for each topic. PS: I Don't like prezi.com. I tried but it simply is too confusing for my students. It zooms here and there. I didn't tried it but I've seen few presentations.

  Read the article

• Server Cabinet/Room Cooling

  - by user37226

  Hello all. I currently have two desktops and three servers in my office sitting on the floor (I know this is bad). With that many servers the ambient temperature in the room goes up quickly. I am located in Dallas, TX so during the winter, if the heat is kept low, it is not a problem, but during the summer it easily jumps the room +10 degrees. I have decided and found a free 42U server cabinet that a hosting company was throwing away to house all of these systems in. One server is in a rack mount case while the other four servers are housed in mid-tower cases. I have purchased shelves for each computer and plan to lay the towers side ways on these shelves (as replacing the cases costs a heck of a lot of money). I like the idea of housing all of these systems in the cabinet because it will save a lot of room and clean up all of the cabling currently laying all over the office floor. When putting this setup together over the next couple of weeks, I want to address issues with dust and cooling. The server cabinet has a fan on top, front plexiglass door and a rear metal door with vent wholes on the bottom. First the cooling issues. I know I am going to want to have cool air enter the bottom of the cabinet and exit the top. I do not want the room heating up though as this will make my work area hot and then make the servers warmer as the air eventually reenters the cabinet. I had an idea to fix this problem, but am unsure if it will work. I was thinking of taking flexible piping and adapting it to the back fans of the computer having the other end of the pipe at the top close to the cabinet's top mounted fan. I was then thinking of creating a duct around the top fan into the attic. Now I am very concerned that the attic will cause issues with this type of setup because during July/August time frame, the attic is easily 120 degrees F. I could also use the flexible pipe to take it to an attic exhaust vent if it would be better to vent it into the 100 degree air outside (at least there may be wind. The other option would be to buy a small portable air conditioner. This may be a possibility, but do I want to spend the extra money on power? I bet this increases the noise. Plus they are around $250 on Amazon. What would you all recommend? Depending on the solution I end up running with above, I would also like to limit the dust that gets into the cabinet. If I were to cut a whole and mount a second cabinet fan on the bottom of the rear door, could I possibly mount a standard home air filter on the other side of that whole? Thanks in advance for your recommendations. I look forward to reading your interesting ideas.

  Read the article

• Server Cabinet/Room Cooling

  - by user37226

  Hello all. I currently have two desktops and three servers in my office sitting on the floor (I know this is bad). With that many servers the ambient temperature in the room goes up quickly. I am located in Dallas, TX so during the winter, if the heat is kept low, it is not a problem, but during the summer it easily jumps the room +10 degrees. I have decided and found a free 42U server cabinet that a hosting company was throwing away to house all of these systems in. One server is in a rack mount case while the other four servers are housed in mid-tower cases. I have purchased shelves for each computer and plan to lay the towers side ways on these shelves (as replacing the cases costs a heck of a lot of money). I like the idea of housing all of these systems in the cabinet because it will save a lot of room and clean up all of the cabling currently laying all over the office floor. When putting this setup together over the next couple of weeks, I want to address issues with dust and cooling. The server cabinet has a fan on top, front plexiglass door and a rear metal door with vent wholes on the bottom. First the cooling issues. I know I am going to want to have cool air enter the bottom of the cabinet and exit the top. I do not want the room heating up though as this will make my work area hot and then make the servers warmer as the air eventually reenters the cabinet. I had an idea to fix this problem, but am unsure if it will work. I was thinking of taking flexible piping and adapting it to the back fans of the computer having the other end of the pipe at the top close to the cabinet's top mounted fan. I was then thinking of creating a duct around the top fan into the attic. Now I am very concerned that the attic will cause issues with this type of setup because during July/August time frame, the attic is easily 120 degrees F. I could also use the flexible pipe to take it to an attic exhaust vent if it would be better to vent it into the 100 degree air outside (at least there may be wind. The other option would be to buy a small portable air conditioner. This may be a possibility, but do I want to spend the extra money on power? I bet this increases the noise. Plus they are around $250 on Amazon. What would you all recommend? Depending on the solution I end up running with above, I would also like to limit the dust that gets into the cabinet. If I were to cut a whole and mount a second cabinet fan on the bottom of the rear door, could I possibly mount a standard home air filter on the other side of that whole? Thanks in advance for your recommendations. I look forward to reading your interesting ideas.

  Read the article

• Ubuntu Server 12.04 CPU Load

  - by zertux

  I have a Server (2x Hexa-Core Xeon E5649 2.53GHz w/HT with 32GB RAM and 20000 GB Bandwidth) running Ubuntu Server 12.04 LTS. The server runs LAMP and serves one website only, the estimated number of users is to be ~ 15,000 at the same time. At the moment i have around 2000 users online each of them runs 50 MySQL queries (small values mostly select and insert) from the beginning until the end of the session. Server CPU Load is high at this number of connections while the RAM usage is almost 1GB out of 32GB its worth mentioning that the server was running very fast with no problems at all but am concerned about the load average. http://s12.postimage.org/z7hi6mz3h/photo.png top - 03:02:43 up 9 min, 2 users, load average: 50.83, 30.14, 12.83 Tasks: 432 total, 1 running, 430 sleeping, 0 stopped, 1 zombie Cpu(s): 0.1%us, 0.2%sy, 0.0%ni, 66.5%id, 33.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 32939992k total, 3111604k used, 29828388k free, 84108k buffers Swap: 2048280k total, 0k used, 2048280k free, 1621640k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2860 root 20 0 25820 2288 1420 S 3 0.0 0:11.18 htop 1182 root 20 0 0 0 0 D 2 0.0 0:01.46 kjournald 1935 mysql 20 0 12.3g 161m 7924 S 1 0.5 102:31.45 mysqld 11 root 20 0 0 0 0 S 0 0.0 0:00.38 kworker/0:1 1822 www-data 20 0 247m 25m 4188 D 0 0.1 0:01.81 apache2 2920 www-data 20 0 0 0 0 Z 0 0.0 0:01.20 apache2 <defunct> 2942 www-data 20 0 247m 23m 3056 D 0 0.1 0:00.20 apache2 3516 www-data 20 0 247m 23m 3028 D 0 0.1 0:00.06 apache2 3521 www-data 20 0 247m 23m 3020 D 0 0.1 0:00.09 apache2 3664 www-data 20 0 247m 23m 3132 D 0 0.1 0:00.09 apache2 3674 www-data 20 0 247m 23m 3252 D 0 0.1 0:00.06 apache2 3713 www-data 20 0 247m 23m 3040 D 0 0.1 0:00.09 apache2 1 root 20 0 24328 2284 1344 S 0 0.0 0:03.09 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root 20 0 0 0 0 S 0 0.0 0:00.01 ksoftirqd/0 6 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/0 7 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 8 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/1 9 root 20 0 0 0 0 S 0 0.0 0:00.00 kworker/1:0 root@server:~/codes# vmstat 1 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 19 0 0 29684012 86112 1689844 0 0 19 590 254 231 48 0 47 5 23 0 0 29704812 86128 1697672 0 0 4 320 11100 8121 77 1 22 0 33 0 0 29671044 86156 1705308 0 0 0 5440 13190 9140 95 1 4 0 33 3 0 29670088 86160 1706288 0 0 0 32932 12275 7297 99 0 1 0 35 0 0 29693456 86188 1710724 0 0 4 676 12701 7867 98 1 1 0 ^C I have not changed any of the default configurations that comes with Ubuntu. Is this load normal for such powerful server ? is there any optimization i can make to Apache/MySQL to minimize the load ? What do you recommend ?

  Read the article

< Previous Page | 584 585 586 587 588 589 590 591 592 593 594 595  | Next Page >