Search Results

Search found 15914 results on 637 pages for 'physical security'.

Page 589/637 | < Previous Page | 585 586 587 588 589 590 591 592 593 594 595 596  | Next Page >

• ASA and cisco vs NSA sonic firewall

  - by Lbaker101

  Currently I’m trying to structure our network to fully support and be redundant with BGP/Multi homing. Our current company size is 40 employees but the major part of that is our Development department. We are a software company and continued connection to the internet is a requirement as 90% of work stops when the net goes down. The only thing hosted on site (that needs to remain up) is our exchange server. Right now i'm faced with 2 different directions and was wondering if I could get your opinions on this. We will have 2 ISPs that are both 20meg up/down and dedicated fiber (so 40megs combined). This is handed off as an Ethernet cable into our server room. ISP#1 first digital ISP#2 CenturyLink we currently have 2x ASA5505s but the 2nd one is not in use. It was there to be a failover and it just needs the security+ license to be matched with the primary device. But this depends on the network structure. I have been looking into the hardware that would be required to be fully redundant and I found that we will either of the following. 2x Cisco 2921+ series routers with failover licenses. They will go in front of the ASAs and either connects in a failover state or 1 ISP into each of the 2921 series routers and then 1 line into each of the ASAs (thus all 4 hardware components will be used actively). So 2x Cisco 2921+ series routers 2x Cisco ASA5505 firewalls The other route 2x SonicWalls NSA2400MX series. 1 primary and the secondary will be in a failover state. This will remove the ASAs from the network and be about 2k cheaper than the cisco route. This also brings down the points of failure because it’s just the 2x sonicwalls It will also allow us to scale all the way up to 200-400 users (depending on their configuration). This also makes so the Sonic walls. So the real question is with the added functionality ect of the sonicwall is there a point in paying so much more to stay the cisco route? Thanks!

  Read the article

• IIS6 Virtual Directory 500 Error on Remote Share

  - by David Boike

  We have our servers at the server farm in a domain. Let's call it LIVE. Our developer computers live in a completely separate corporate domain, miles and miles away. Let's call it CORP. We have a large central storage unit (unix) that houses images and other media needed by many webservers in the server farm. The IIS application pools run as (let's say) LIVE\MediaUser and use those credentials to connect to a central storage share as a virtual directory, retrieve the images, and serve them as if they were local on each server. The problem is in development. On my development machine. I log in as CORP\MyName. My IIS 6 application pool runs as Network Service. I can't run it as a user from the LIVE domain because my machine isn't (and can not be) joined to that domain. I try to create a virtual directory, point it to the same network directory, click Connect As, uncheck the "Always use the authenticated user's credentials when validating access to the network directory" checkbox so that I can enter the login info, enter the credentails for LIVE\MediaUser, click OK, verify the password, etc. This doesn't work. I get "HTTP Error 500 - Internal server error" from IIS. The IIS log file reports sc-status = 500, sc-substatus = 16, and sc-win32-status = 1326. The documentation says this means "UNC authorization credentials are incorrect" and the Win32 status means "Logon failure: unknown user name or bad password." This would be all and good if it were anywhere close to accurate. I double- and trouble-checked it. Tried multiple known good logins. The IIS manager allows me to view the file tree in its window, it's only the browser that kicks me out. I even tried going to the virtual directory's Directory Security tab, and under Authentication and Access Control, I tried using the same LIVE domain username for the anonymous access credential. No luck. I'm not trying to run any ASP, ASP.NET, or other dynamic anything out of the virtual directory. I just want IIS to be able to load static images, css, and js files. If anyone has some bright ideas I would be most appreciative!

  Read the article

• Server 2008 Likes to restart itself

  - by Campo

  I have a weird issue here. I notice about once a week the web server restarts itself. This would be only a minor issue if we were not planning on implementing an IP failover. I have checked the event logs. I don't see anything that indicates a reason for the restart. I need some help diagnosing the reason the server restarts. It happened last night at 5:00AM Last even in the log was 1 hour before the unexpected shutdown. Here is the Log for the shutdown event. Any help is much appreciated. I know there isn't much to go on yet. Log Name: System Source: EventLog Date: 5/5/2010 5:01:12 AM Event ID: 6008 Task Category: None Level: Error Keywords: Classic User: N/A Computer: SERVERNAME Description: The previous system shutdown at 4:56:41 AM on 5/5/2010 was unexpected. Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="EventLog" /> <EventID Qualifiers="32768">6008</EventID> <Level>2</Level> <Task>0</Task> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2010-05-05T09:01:12.000Z" /> <EventRecordID>346094</EventRecordID> <Channel>System</Channel> <Computer>SERVERNAME</Computer> <Security /> </System> <EventData> <Data>4:56:41 AM</Data> <Data>5/5/2010</Data> <Data> </Data> <Data> </Data> <Data>39594</Data> <Data> </Data> <Data> </Data> <Binary>DA070500030005000400380029008E03DA070500030005000800380029008E033C0000003C000000000 000000000000000000000000000000100000000000000</Binary> </EventData> </Event>

  Read the article

• How do i enable innodb on ubuntu server 10.04

  - by Matt

  Here is my entire my.cnf [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] key_buffer = 224M sort_buffer_size = 4M read_buffer_size = 4M read_rnd_buffer_size = 4M myisam_sort_buffer_size = 12M query_cache_size = 44M # # * Basic Settings # # # * IMPORTANT # If you make changes to these settings and your system uses apparmor, you may # also need to also adjust /etc/apparmor.d/usr.sbin.mysqld. # user = mysql socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. bind-address = 127.0.0.1 # # * Fine Tuning # #key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #max_connections = 100 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M #query_cache_size = 16M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 log_error = /var/log/mysql/error.log # Here you can see queries with especially long duration #log_slow_queries = /var/log/mysql/mysql-slow.log #long_query_time = 2 #log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/ And here is my show engines call....i have no idea what i need to do to enable innodb show engines; +------------+---------+----------------------------------------------------------------+--------------+------+------------+ | Engine | Support | Comment | Transactions | XA | Savepoints | +------------+---------+----------------------------------------------------------------+--------------+------+------------+ | MyISAM | DEFAULT | Default engine as of MySQL 3.23 with great performance | NO | NO | NO | | MRG_MYISAM | YES | Collection of identical MyISAM tables | NO | NO | NO | | BLACKHOLE | YES | /dev/null storage engine (anything you write to it disappears) | NO | NO | NO | | CSV | YES | CSV storage engine | NO | NO | NO | | MEMORY | YES | Hash based, stored in memory, useful for temporary tables | NO | NO | NO | | FEDERATED | NO | Federated MySQL storage engine | NULL | NULL | NULL | | ARCHIVE | YES | Archive storage engine | NO | NO | NO | +------------+---------+----------------------------------------------------------------+--------------+------+------------+ 7 rows in set (0.00 sec)

  Read the article

• Putting indexes in separate filegroup kills our queries

  - by womp

  Can anyone shed some light on this? On our dev boxes, our database resides entirely in the PRIMARY filegroup, and everything works fine. On one of our production servers, recently upgraded from 2005 to 2008, we noticed it was performing slower than it should. On this machine, there are two filegroups - PRIMARY and INDEXES. Both filegroups contain 1 file per logical volume, one logical volume per CPU, (and each logical volume is a RAID 10 of 4 physical disks). We isolated a few queries that were performing fast on the dev boxes and slow (up to 40x slower) on the production machine. Turned out these queries were using the non-clustered indexes that resided in the INDEXES filegroup. Tweaking some of the queries to only use clustered indexes that were in the PRIMARY filegroup dropped their times back to normal. As a final confirmation, we redeployed the same database on the same machine to have everything in PRIMARY, and things went back to normal! Here's the statistics output of one of the queries, run identically on the machine with different filegroup configurations (table names changed to protect the innocent): FAST (everything in PRIMARY filegroup): (3 row(s) affected) Table '0'. Scan count 2, logical reads 14, ... Table '1'. Scan count 0, logical reads 0, ... Table '1'. Scan count 0, logical reads 0, ... Table '2'. Scan count 2, logical reads 7, ... Table '3'. Scan count 2, logical reads 1012, ... Table '4'. Scan count 1, logical reads 3, ... SQL Server Execution Times: CPU time = 437 ms, elapsed time = 445 ms. SLOW (indexes split into their own filegroup): (3 row(s) affected) Table '0'. Scan count 209, logical reads 428, ... Table '1'. Scan count 0, logical reads 0,... Table '2'. Scan count 1021, logical reads 9043,.... Table '3'. Scan count 209, logical reads 105754, .... Table '4'. Scan count 0, logical reads 0, .... Table '5'. Scan count 1, logical reads 695, ... **Table '#46DA8CA9'. Scan count 205, logical reads 205, ...** Table '6'. Scan count 6, logical reads 436, ... Table '7'. Scan count 1, logical reads 12,.... SQL Server Execution Times: CPU time = 17581 ms, elapsed time = 17595 ms. Notice the weird temp table and extra tables involved in the slow query. It seems clear that having a second file group is making SQL Server batty with choosing an execution plan. What the heck is going on?

  Read the article

• Finding underlying cause of Window 7 Account corruption.

  - by Carl Jokl

  I have been having trouble with my Sister's computer which I built. It is running Windows 7 Ultimate x64. The problem is that I have had problems with the accounts becoming corrupted. First problems manifest themselves in the form of Windows saying the profile failed to be loaded properly and a temporary profile. Eventually the account will not allow login at all. An error message along the lines the authentication service failing the login. I have found information about this problem and how to fix it. The problem being that something has corrupted the account profile and backing up and recreating the accounts fixes the problem. I have been able to fix things and get logins working again but over the period of usually about a week it happens again. Bit by bit the accounts corrupt and then it is back to square one. I am frustrated because I don't know what the underlying cause of the problem is i.e. what is causing the accounts to be corrupted in the first place. At the moment I am just treating the symptoms. I was hoping someone who may have more experience with dealing with this problem might be able to help me find the root cause. Some articles suggest that Norton Internet Security is a big culprit of this problem which is installed. I could try uninstalling Norton and see if it helps. The one thing which is different about this computer to any other I have built is that it has a solid state drive. Actually it has both a hard drive and solid state drive. The documents and settings i.e. the Users directory is stored on the hard drive. This was done following an article about moving the user account data onto a separate drive on Windows 7 which I found on the Internet. Moving the User accounts is more of a pain under Windows 7 and this solution involved creating a low level file system link to the folder from the boot drive (Solid State) to the Hard Drive. The idea is that the computer behaves just as if it is accessing the User's folder from the boot drive but actually the data is stored on the hard drive. This may have nothing to do with the cause of the problem but due to the problem being user account corruption it is a possibility I have not been able to rule out. Any help would be appreciated as I would be glad to see the back of this problem.

  Read the article

• Causes of sudden massive filesystem damage? ("root inode is not a directory")

  - by poolie

  I have a laptop running Maverick (very happily until yesterday), with a Patriot Torx SSD; LUKS encryption of the whole partition; one lvm physical volume on top of that; then home and root in ext4 logical volumes on top of that. When I tried to boot it yesterday, it complained that it couldn't mount the root filesystem. Running fsck, basically every inode seems to be wrong. Both home and root filesystems show similar problems. Checking a backup superblock doesn't help. e2fsck 1.41.12 (17-May-2010) lithe_root was not cleanly unmounted, check forced. Resize inode not valid. Recreate? no Pass 1: Checking inodes, blocks, and sizes Root inode is not a directory. Clear? no Root inode has dtime set (probably due to old mke2fs). Fix? no Inode 2 is in use, but has dtime set. Fix? no Inode 2 has a extra size (4730) which is invalid Fix? no Inode 2 has compression flag set on filesystem without compression support. Clear? no Inode 2 has INDEX_FL flag set but is not a directory. Clear HTree index? no HTREE directory inode 2 has an invalid root node. Clear HTree index? no Inode 2, i_size is 9581392125871137995, should be 0. Fix? no Inode 2, i_blocks is 40456527802719, should be 0. Fix? no Reserved inode 3 (<The ACL index inode>) has invalid mode. Clear? no Inode 3 has compression flag set on filesystem without compression support. Clear? no Inode 3 has INDEX_FL flag set but is not a directory. Clear HTree index? no .... Running strings across the filesystems, I can see there are what look like filenames and user data there. I do have sufficiently good backups (touch wood) that it's not worth grovelling around to pull back individual files, though I might save an image of the unencrypted disk before I rebuild, just in case. smartctl doesn't show any errors, neither does the kernel log. Running a write-mode badblocks across the swap lv doesn't find problems either. So the disk may be failing, but not in an obvious way. At this point I'm basically, as they say, fscked? Back to reinstalling, perhaps running badblocks over the disk, then restoring from backup? There doesn't even seem to be enough data to file a meaningful bug... I don't recall that this machine crashed last time I used it. At this point I suspect a bug or memory corruption caused it to write garbage across the disks when it was last running, or some kind of subtle failure mode for the SSD. What do you think would have caused this? Is there anything else you'd try?

  Read the article

• Proliant server will not accept new hard disks in RAID 1+0?

  - by Leigh

  I have a HP ProLiant DL380 G5, I have two logical drives configured with RAID. I have one logical drive RAID 1+0 with two 72 gb 10k sas 1 port spare no 376597-001. I had one hard disk fail and ordered a replacement. The configuration utility showed error and would not rebuild the RAID. I presumed a hard disk fault and ordered a replacement again. In the mean time I put the original failed disk back in the server and this started rebuilding. Currently shows ok status however in the log I can see hardware errors. The new disk has come and I again have the same problem of not accepting the hard disk. I have updated the P400 controller with the latest firmware 7.24 , but still no luck. The only difference I can see is the original drive has firmware 0103 (same as the RAID drive) and the new one has HPD2. Any advice would be appreciated. Thanks in advance Logs from server ctrl all show config Smart Array P400 in Slot 1 (sn: PAFGK0P9VWO0UQ) array A (SAS, Unused Space: 0 MB) logicaldrive 1 (68.5 GB, RAID 1, Interim Recovery Mode) physicaldrive 2I:1:1 (port 2I:box 1:bay 1, SAS, 73.5 GB, OK) physicaldrive 2I:1:2 (port 2I:box 1:bay 2, SAS, 72 GB, Failed array B (SAS, Unused Space: 0 MB) logicaldrive 2 (558.7 GB, RAID 5, OK) physicaldrive 1I:1:5 (port 1I:box 1:bay 5, SAS, 300 GB, OK) physicaldrive 2I:1:3 (port 2I:box 1:bay 3, SAS, 300 GB, OK) physicaldrive 2I:1:4 (port 2I:box 1:bay 4, SAS, 300 GB, OK) ctrl all show config detail Smart Array P400 in Slot 1 Bus Interface: PCI Slot: 1 Serial Number: PAFGK0P9VWO0UQ Cache Serial Number: PA82C0J9VWL8I7 RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: E Firmware Version: 7.24 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Status Details: A cache error was detected. Run more information. Cache Ratio: 100% Read / 0% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Battery/Capacitor Count: 0 SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 0 MB Status: Failed Physical Drive Array Type: Data One of the drives on this array have failed or has Logical Drive: 1 Size: 68.5 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 17594 Strip Size: 128 KB Full Stripe Size: 128 KB Status: Interim Recovery Mode Caching: Enabled Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive0 Mount Points: C:\ 68.5 GB Logical Drive Label: A0100539PAFGK0P9VWO0UQ0E93 Mirror Group 0: physicaldrive 2I:1:2 (port 2I:box 1:bay 2, S Mirror Group 1: physicaldrive 2I:1:1 (port 2I:box 1:bay 1, S Drive Type: Data physicaldrive 2I:1:1 Port: 2I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 73.5 GB Rotational Speed: 10000 Firmware Revision: 0103 Serial Number: B379P8C006RK Model: HP DG072A9B7 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:2 Port: 2I Box: 1 Bay: 2 Status: Failed Drive Type: Data Drive Interface Type: SAS Size: 72 GB Rotational Speed: 15000 Firmware Revision: HPD9 Serial Number: D5A1PCA04SL01244 Model: HP EH0072FARUA PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data Logical Drive: 2 Size: 558.7 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Co Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive1 Mount Points: E:\ 558.7 GB Logical Drive Label: AF14FD12PAFGK0P9VWO0UQD007 Drive Type: Data physicaldrive 1I:1:5 Port: 1I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE07QH300009923X1X3 Model: HP DG0300BALVP Current Temperature (C): 32 Maximum Temperature (C): 45 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:3 Port: 2I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE0AHVH00009924P8F3 Model: HP DG0300BALVP Current Temperature (C): 34 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:4 Port: 2I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE08NAK00009924KWD6 Model: HP DG0300BALVP Current Temperature (C): 35 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown

  Read the article

• SSH to an ubuntu machine using avahi

  - by tensaiji

  I have an ubuntu box that I connect to using avahi. Connecting to that box works fine for all services (I regularly use AFP, SSH and SMB on it) but I've noticed that whenever I connect to it from a mac using SSH (and using the ".local" dns name provided by avahi - eg. "ssh .local") SSH tries to connect using ipv6, which for some reason times out (after two minutes) then it tries ipv4 which connects immediately. I'd like to avoid this timeout, as it's really annoying for me and other users - if SSH tried ipv4 first or if ssh over ipv6 worked then that would solve the problem. But so far I've been unable to get either to work (the best I've managed is to specify the "-4" option to SSH to stop it from trying ipv6 at all). I'm using Ubuntu 10.04. Any solution has to be on the server (not the client) as there are multiple clients connecting. A possible complication might be that my LAN is set up to allow link-local ipv6 addresses only, but I have other servers (using Mac OS) that I can SSH into using ipv6) I suspect that the problem could be solved by either preventing avahi from broadcasting the ipv6 address, or by enabling ssh over ipv6, but so far as I can tell avahi is already configured not to broadcast the ipv6 address and sshd is configured to allow ipv6 connections! Here's my /etc/avahi/avahi-daemon.conf (I don't think I've changed anything from the ubuntu defaults) [server] #host-name=foo #domain-name=local #browse-domains=0pointer.de, zeroconf.org use-ipv4=yes use-ipv6=no #allow-interfaces=eth0 #deny-interfaces=eth1 #check-response-ttl=no #use-iff-running=no #enable-dbus=yes #disallow-other-stacks=no #allow-point-to-point=no [wide-area] enable-wide-area=yes [publish] #disable-publishing=no #disable-user-service-publishing=no #add-service-cookie=no #publish-addresses=yes #publish-hinfo=yes #publish-workstation=yes #publish-domain=yes #publish-dns-servers=192.168.50.1, 192.168.50.2 #publish-resolv-conf-dns-servers=yes #publish-aaaa-on-ipv4=yes #publish-a-on-ipv6=no [reflector] #enable-reflector=no #reflect-ipv=no [rlimits] #rlimit-as= rlimit-core=0 rlimit-data=4194304 rlimit-fsize=0 rlimit-nofile=300 rlimit-stack=4194304 rlimit-nproc=3 and here's my sshd_config (mainly updated to only allow pub/private keys): # What ports, IPs and protocols we listen for Port 22 # Use these options to restrict which interfaces/protocols sshd will bind to #ListenAddress :: #ListenAddress 0.0.0.0 Protocol 2 # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key #Privilege Separation is turned on for security UsePrivilegeSeparation yes # Lifetime and size of ephemeral version 1 server key KeyRegenerationInterval 3600 ServerKeyBits 768 # Logging SyslogFacility AUTH LogLevel INFO # Authentication: LoginGraceTime 180 PermitRootLogin no StrictModes yes RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files IgnoreRhosts yes # For this to work you will also need host keys in /etc/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 HostbasedAuthentication no # Uncomment if you don't trust ~/.ssh/known_hosts for RhostsRSAAuthentication #IgnoreUserKnownHosts yes # To enable empty passwords, change to yes (NOT RECOMMENDED) PermitEmptyPasswords no # Change to yes to enable challenge-response passwords (beware issues with # some PAM modules and threads) ChallengeResponseAuthentication no # Change to no to disable tunnelled clear text passwords PasswordAuthentication no AllowGroups sshusers # Kerberos options #KerberosAuthentication no #KerberosGetAFSToken no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes X11Forwarding yes X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no MaxStartups 10:30:60 #Banner /etc/issue.net # Allow client to pass locale environment variables AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server UsePAM yes Does anyone have any ideas that I can try, or has experienced anything similar?

  Read the article

• What's the best way to do user profile/folder redirect/home directory archiving?

  - by tpederson

  My company is in dire need of a redesign around how we handle user account administration. I've been tasked with automating the process. The end goal is to have the whole works triggered by the business, and IT only looking in when there's an error reported. The interim phase is going to be semi-manual. That is a level 2 tech inputs the user's info and supervises the process. The current hurdle I'm facing is user profile archiving. Our security team requires us to archive the profile directories for any terminated user for 60 days in case the legal team requires access to their files. Our AD is as much a mess as everything else, so there are some users with home directories and some with profiles. Anyone who has a profile dir in AD also has a good deal of their profile redirected to our file servers over DFS. In order to complete the process manually you find the user in AD, disable them, find their home/profile dir, go there and take ownership, create an archive folder, move all their files over, then delete the old dir. Some users have many many gigs of nonsense and this can take quite some time. Even automated the process would not be a quick one. I'm thinking that I need to have a client side C# GUI for the quick stuff and some server side batch script or console app to offload this long running process. I have a batch script that works decently using takeown and robocopy, but I wonder if a C# console app would do a better job. So, my question at long last is, what do you think is the best way to handle this? I can't imagine this is a unique problem, how do other admins get this done? The last place I worked was easily 10x larger than the place I'm in now. If we would have been doing this manual crap there, they'd have needed a team of at least 30 full time workers to keep up. I have decent skills in C#.net and batch scripting, but am a quick study and I have used most every language once or twice. Thank you for reading this and I look forward to seeing what imaginative solutions you all can come up with.

  Read the article

• http://localhost/ always gives 502 unknown host

  - by Nitesh Panchal

  My service for World Wide Web Publishing Service started successfully but whenever I browse to http://localhost/ I always get 502 Unknown host. Also, wampapache is installed side by side but when I stop IIS service and start wampapache from services.msc I get error and when I view it in System event log I get this error: - <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> - <System> <Provider Name="Service Control Manager" Guid="{555908d1-a6d7-4695-8e1e-26931d2012f4}" EventSourceName="Service Control Manager" /> <EventID Qualifiers="49152">7024</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x8080000000000000</Keywords> <TimeCreated SystemTime="2011-06-12T17:43:28.223498400Z" /> <EventRecordID>346799</EventRecordID> <Correlation /> <Execution ProcessID="456" ThreadID="3936" /> <Channel>System</Channel> <Computer>MACHINENAME</Computer> <Security /> </System> - <EventData> <Data Name="param1">wampapache</Data> <Data Name="param2">%%1</Data> </EventData> </Event> I am fed up of this error and it is driving me nuts. I feel like banging my head against the laptop. I am really serious. Without concentrating on my real application I am trying to solve this issue since 3 hours. I google various threads and few of them said that there could be issue of Reporting Services or Skype. But I have uninstalled Skype and Reporting Services are disabled. What more should I do? I have hosts file present in etc directory and it does have mapping for localhost to 127.0.0.1. What more could I do?

  Read the article

• Cisco 678 Will Not Work using PPPoE - Possibly Because I Configured it Incorrectly..?

  - by Brian Stinar

  I am attempting to configure a Cisco 678 because I am totally sick on my Actiontec. However, I am running into some problems. It seems as though the Cisco is able to train the line, but I am unable to ping out. I am all right at programming, but still learning a lot when it comes to being a system administrator. I apologize in advance if I did something ridiculous, or am attempting to configure this device to do something it was not designed to do. It is almost like I am not correctly configuring the device to grab it's IP using PPPoA (like my Actiontec.) The output from "show running" (below) makes me think this too. Below are the commands I ran in order to configure this: # en # set nvram erase # write # reboot # en # set nat enable # set dhcp server enable # set PPP wan0-0 ipcp 0.0.0.0 # set ppp wan0-0 dns 0.0.0.0 # set PPP wan0-0 login xxxxx // My actual login # set PPP wan0-0 password yyyyy // My actual password # set PPP restart enabled # set int wan0-0 close # set int wan0-0 vpi 0 # set int wan0-0 vci 32 # set int wan0-0 open # write # reboot Here is the output from a few commands I thought could provide some useful information: cbos#ping 74.125.224.113 Sending 1 8 byte ping(s) to 74.125.224.113 every 2 second(s) Request timed out cbos#show version Cisco Broadband Operating System CBOS (tm) 678 Software (C678-I-M), Version v2.4.9 - Release Software Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Nov 17 2004 15:26:29 DMT FULL firmware version G96 NVRAM image at 0x1030f000 cbos#show errors - Current Error Messages - ## Ticks Module Level Message 0 000:00:00:00 PPP Info IPCP Open Event on wan0-0 1 000:00:00:14 ATM Info Wan0 Up 2 000:00:00:14 PPP Info PPP Up Event on wan0-0 3 000:00:01:54 PPP Info PPP Down Event on wan0-0 Total Number of Error Messages: 4 cbos#show interface wan0 wan0 ADSL Physical Port Line Trained Actual Configuration: Overhead Framing: 3 Trellis Coding: Enabled Standard Compliance: T1.413 Downstream Data Rate: 1184 Kbps Upstream Data Rate: 928 Kbps Interleave S Downstream: 4 Interleave D Downstream: 16 Interleave R Downstream: 16 Interleave S Upstream: 4 Interleave D Upstream: 8 Interleave R Upstream: 16 Modem Microcode: G96 DSP version: 0 Operating State: Showtime/Data Mode Configured: Echo Cancellation: Disabled Overhead Framing: 3 Coding Gain: Auto TX Power Attenuation: 0dB Trellis Coding: Enabled Bit Swapping: Disabled Standard Compliance: T1.413 Remote Standard Compliance: T1.413 Tx Start Bin: 0x6 Tx End Bin: 0x1f Data Interface: Utopia L1 Status: Local SNR Margin: 19.0dB Local Coding Gain: 7.5dB Local Transmit Power: 12.5dB Local Attenuation: 46.0dB Remote Attenuation: 31.0dB Local Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 2 No Cell Delineation Interleaved: 0 Out of Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 Remote Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 1 No Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 cbos#show int wan0-0 WAN0-0 ATM Logical Port PVC (VPI 0, VCI 32) is configured. ScalaRate set to Auto AAL 5 UBR Traffic IP Port Enabled cbos#show running Warning: traffic may pause while NVRAM is being accessed [[ CBOS = Section Start ]] NSOS MD5 Enable Password = XXXX NSOS MD5 Root Password = XXXX NSOS MD5 Commander Password = XXXX [[ PPP Device Driver = Section Start ]] PPP Port User Name = 00, "XXXX" PPP Port User Password = 00, XXXX PPP Port Option = 00, IPCP,IP Address,3,Auto,Negotiation Not Required,Negotiable ,IP,0.0.0.0 PPP Port Option = 00, IPCP,Primary DNS Server,129,Auto,Negotiation Not Required, Negotiable,IP,0.0.0.0 PPP Port Option = 00, IPCP,Secondary DNS Server,131,Auto,Negotiation Not Require d,Negotiable,IP,0.0.0.0 [[ ATM WAN Device Driver = Section Start ]] ATM WAN Virtual Connection Parms = 00, 0, 32, 0 [[ DHCP = Section Start ]] DHCP Server = enabled [[ IP Routing = Section Start ]] IP NAT = enabled [[ WEB = Section Start ]] WEB = enabled cbos# wtf...? Thank you all very much for taking the time to read this, and the help.

  Read the article

• Airport Express chokes Wi-Fi for a few seconds, several times per hour. Any idea why?

  - by user13727

  I'm using a MacBookPro connected to an AiportExpress' Wi-FI network. Every once in a while, the Wi-Fi will choke up and either drop some packets, or lag horribly for several seconds. I'm losing hair over this because every time I chat on Skype, the call hangs randomly due to this problem. Any idea what's wrong? Some more details: two networks are set up: 2.4Ghz and 5Ghz, and the issue happens on both the network uses WPA2 Personal for security the Airport is in the same room with my computer the Airport is fairly new, bought this summer, model number off the back: A1392 tried connecting to a neighbours wifi to see if it's a problem with my computer, or interference. It's not, it doesn't happen on their network. tried resetting it several times tried changing channels manually Ping results are below, so you can see what I'm talking about. EDIT: 10.0.1.1 is the Airport's IP 64 bytes from 10.0.1.1: icmp_seq=1795 ttl=255 time=0.813 ms 64 bytes from 10.0.1.1: icmp_seq=1796 ttl=255 time=3.335 ms 64 bytes from 10.0.1.1: icmp_seq=1797 ttl=255 time=3.403 ms 64 bytes from 10.0.1.1: icmp_seq=1798 ttl=255 time=3.414 ms 64 bytes from 10.0.1.1: icmp_seq=1799 ttl=255 time=3.227 ms 64 bytes from 10.0.1.1: icmp_seq=1800 ttl=255 time=3.274 ms 64 bytes from 10.0.1.1: icmp_seq=1801 ttl=255 time=3.253 ms 64 bytes from 10.0.1.1: icmp_seq=1802 ttl=255 time=3.292 ms >>>> choke starts <<< 64 bytes from 10.0.1.1: icmp_seq=1803 ttl=255 time=53.977 ms 64 bytes from 10.0.1.1: icmp_seq=1804 ttl=255 time=35.049 ms 64 bytes from 10.0.1.1: icmp_seq=1805 ttl=255 time=19.820 ms >>>> choke ends <<< 64 bytes from 10.0.1.1: icmp_seq=1806 ttl=255 time=0.716 ms 64 bytes from 10.0.1.1: icmp_seq=1807 ttl=255 time=0.705 ms 64 bytes from 10.0.1.1: icmp_seq=1808 ttl=255 time=0.919 ms 64 bytes from 10.0.1.1: icmp_seq=1809 ttl=255 time=0.659 ms 64 bytes from 10.0.1.1: icmp_seq=1810 ttl=255 time=0.877 ms 64 bytes from 10.0.1.1: icmp_seq=1811 ttl=255 time=0.679 ms 64 bytes from 10.0.1.1: icmp_seq=1812 ttl=255 time=0.854 ms 64 bytes from 10.0.1.1: icmp_seq=1813 ttl=255 time=0.644 ms 64 bytes from 10.0.1.1: icmp_seq=1814 ttl=255 time=3.779 ms ... time passes .. 64 bytes from 10.0.1.1: icmp_seq=1599 ttl=255 time=0.674 ms 64 bytes from 10.0.1.1: icmp_seq=1600 ttl=255 time=0.930 ms 64 bytes from 10.0.1.1: icmp_seq=1601 ttl=255 time=0.665 ms 64 bytes from 10.0.1.1: icmp_seq=1602 ttl=255 time=1.085 ms Request timeout for icmp_seq 1603 Request timeout for icmp_seq 1604 64 bytes from 10.0.1.1: icmp_seq=1605 ttl=255 time=104.969 ms 64 bytes from 10.0.1.1: icmp_seq=1606 ttl=255 time=11.521 ms 64 bytes from 10.0.1.1: icmp_seq=1607 ttl=255 time=0.926 ms 64 bytes from 10.0.1.1: icmp_seq=1608 ttl=255 time=0.993 ms 64 bytes from 10.0.1.1: icmp_seq=1609 ttl=255 time=0.745 ms And the Signal-Noise ratio:

  Read the article

• Can't connect to svnserve on localhost - connection actively refused

  - by RMorrisey

  When I try to connect using Tortoise to my SVN server using: svn://localhost/ Tortoise tells me: "Can't connect to host 'localhost'. No connection could be made because the target machine actively refused it." How can I fix this? I am trying to set up a subversion server on my local PC for personal use. I am running Windows Vista, with SlikSVN and TortoiseSVN installed. I previously had everything working correctly, but I found that I couldn't merge(!), apparently due to a version mismatch between the SVN client and server. Anyway... I now have the following setup: I created a repository using svnadmin create; it resides at C:\svnGrove C:\svnGrove\conf\svnserve.conf (# comments omitted): [general] anon-access=read auth-access=write password-db=passwd #authz-db=authz realm=svnGrove C:\svnGrove\conf\passwd: [users] myname=mypass My Subversion Server service is pointed to: C:\Program Files\SlikSvn\bin\svnserve.exe --service -r C:\svnGrove It shows the TCP/IP service as a dependency. I have also tried running svnserve from the command line, with similar results. The below is provided by the 'about' option in TortoiseSVN: TortoiseSVN 1.6.10, Build 19898 - 32 Bit , 2010/07/16 15:46:08 Subversion 1.6.12, apr 1.3.8 apr-utils 1.3.9 neon 0.29.3 OpenSSL 0.9.8o 01 Jun 2010 zlib 1.2.3 The following is from svn --version on the command line (not sure why it says CollabNet, CollabNet was the previous SVN binary that I had set up. The uninstaller failed to remove everything gracefully): svn, version 1.6.12 (SlikSvn/1.6.12) WIN32 compiled Jun 22 2010, 20:45:29 Copyright (C) 2000-2009 CollabNet. Subversion is open source software, see http://subversion.tigris.org/ This product includes software developed by CollabNet (http://www.Collab.Net/). The following repository access (RA) modules are available: * ra_neon : Module for accessing a repository via WebDAV protocol using Neon. - handles 'http' scheme - handles 'https' scheme * ra_svn : Module for accessing a repository using the svn network protocol. - with Cyrus SASL authentication - handles 'svn' scheme * ra_local : Module for accessing a repository on local disk. - handles 'file' scheme * ra_serf : Module for accessing a repository via WebDAV protocol using serf. - handles 'http' scheme - handles 'https' scheme I disabled my Windows Firewall and CA Internet Security, without success in resolving the issue. Edit The old version of svnserve was still set up as a service after the uninstall, pointed to this path: C:\Program Files\Subversion\svn-win32-1.4.6\bin I edited the registry key for the service to point to the new path (shown above). Whether I run svnserve as a service, or using -d, I do not see an entry for that port number in the listing generated by netstat -anp tcp.

  Read the article

• Different files on shared partition?

  - by Matt Robertson

  I am dual-booting Windows 8 and Ubuntu 12.04. My partition scheme looks like this: /dev/sda1 - Windows 8 (nfts) /dev/sda2 - Ubuntu / (ext4) /dev/sda3 - Ubuntu home (ext4) /dev/sda5 - swap /dev/sda6 - Shared data partition (exfat) (First off, yes I do have exfat libraries installed on Ubuntu) I created some PNG images in Windows and saved them on my shared partition. From Ubuntu, I edited the images in GIMP and saved them (replacing the ones on the shared partition). When I boot into Windows, the files appear unchanged - exactly like they did before I edited them from Ubuntu. I even added a folder and deleted some other files, but none of these changes exist in Windows. When I boot into Ubuntu, all of the changes are still there. It is as if Windows is caching the old file structure... How is this possible? Thanks in advance. Edit -- commands output ~~ lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 0 465.8G 0 disk +-sda1 8:1 0 165.1G 0 part +-sda2 8:2 0 21.3G 0 part / +-sda3 8:3 0 98.9G 0 part /home +-sda4 8:4 0 1K 0 part +-sda5 8:5 0 7.8G 0 part [SWAP] +-sda6 8:6 0 172.7G 0 part /mnt/shared_data ~~ /etc/fstab # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # /dev/sda2 UUID=8f700f65-b5c7-4afc-a6fb-8f9271e0fb5e / ext4 errors=remount-ro 0 1 # /dev/sda3 UUID=f0d688b7-22bd-4fa7-bc1b-a594af2933fa /home ext4 defaults 0 2 # /dev/sda5 UUID=3bc2399b-5deb-4f04-924b-d4fc77491997 none swap sw 0 0 # /dev/sda6 UUID=F2DE-BC47 /mnt/shared_data exfat defaults 0 3 ~~ /etc/mtab /dev/sda2 / ext4 rw,errors=remount-ro 0 0 proc /proc proc rw,noexec,nosuid,nodev 0 0 sysfs /sys sysfs rw,noexec,nosuid,nodev 0 0 none /sys/fs/fuse/connections fusectl rw 0 0 none /sys/kernel/debug debugfs rw 0 0 none /sys/kernel/security securityfs rw 0 0 udev /dev devtmpfs rw,mode=0755 0 0 devpts /dev/pts devpts rw,noexec,nosuid,gid=5,mode=0620 0 0 tmpfs /run tmpfs rw,noexec,nosuid,size=10%,mode=0755 0 0 none /run/lock tmpfs rw,noexec,nosuid,nodev,size=5242880 0 0 none /run/shm tmpfs rw,nosuid,nodev 0 0 /dev/sda3 /home ext4 rw 0 0 /dev/sda6 /mnt/shared_data fuseblk rw,nosuid,nodev,allow_other,blksize=4096 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,noexec,nosuid,nodev 0 0 gvfs-fuse-daemon /home/matt/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,user=matt 0 0

  Read the article

• Suspicious process running under user named

  - by Amit

  I get a lot of emails reporting this and I want this issue to auto correct itself. These process are run by my server and are a result of updates, session deletion and other legitimate session handling reported as false positives. Here's a sample report: Time: Sat Oct 20 00:00:03 2012 -0400 PID: 20077 Account: named Uptime: 326117 seconds Executable: /usr/sbin/nsd\00507d27e9\0053\00\00\00\00\00 (deleted) The file system shows this process is running an executable file that has been deleted. This typically happens when the original file has been replaced by a new file when the application is updated. To prevent this being reported again, restart the process that runs this excecutable file. See csf.conf and the PT_DELETED text for more information about the security implications of processes running deleted executable files. Command Line (often faked in exploits): /usr/sbin/nsd -c /etc/nsd/nsd.conf Network connections by the process (if any): udp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 udp: 127.0.0.1:53 -> 0.0.0.0:0 udp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 tcp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 tcp: 127.0.0.1:53 -> 0.0.0.0:0 tcp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 Files open by the process (if any): /dev/null /dev/null /dev/null Memory maps by the process (if any): 0045e000-00479000 r-xp 00000000 fd:00 2582025 /lib/ld-2.5.so 00479000-0047a000 r--p 0001a000 fd:00 2582025 /lib/ld-2.5.so 0047a000-0047b000 rw-p 0001b000 fd:00 2582025 /lib/ld-2.5.so 0047d000-005d5000 r-xp 00000000 fd:00 2582073 /lib/i686/nosegneg/libc-2.5.so 005d5000-005d7000 r--p 00157000 fd:00 2582073 /lib/i686/nosegneg/libc-2.5.so 005d7000-005d8000 rw-p 00159000 fd:00 2582073 /lib/i686/nosegneg/libc-2.5.so 005d8000-005db000 rw-p 005d8000 00:00 0 005dd000-005e0000 r-xp 00000000 fd:00 2582087 /lib/libdl-2.5.so 005e0000-005e1000 r--p 00002000 fd:00 2582087 /lib/libdl-2.5.so 005e1000-005e2000 rw-p 00003000 fd:00 2582087 /lib/libdl-2.5.so 0062b000-0063d000 r-xp 00000000 fd:00 2582079 /lib/libz.so.1.2.3 0063d000-0063e000 rw-p 00011000 fd:00 2582079 /lib/libz.so.1.2.3 00855000-0085f000 r-xp 00000000 fd:00 2582022 /lib/libnss_files-2.5.so 0085f000-00860000 r--p 00009000 fd:00 2582022 /lib/libnss_files-2.5.so 00860000-00861000 rw-p 0000a000 fd:00 2582022 /lib/libnss_files-2.5.so 00ac0000-00bea000 r-xp 00000000 fd:00 2582166 /lib/libcrypto.so.0.9.8e 00bea000-00bfe000 rw-p 00129000 fd:00 2582166 /lib/libcrypto.so.0.9.8e 00bfe000-00c01000 rw-p 00bfe000 00:00 0 00e68000-00e69000 r-xp 00e68000 00:00 0 [vdso] 08048000-08074000 r-xp 00000000 fd:00 927261 /usr/sbin/nsd 08074000-08079000 rw-p 0002b000 fd:00 927261 /usr/sbin/nsd 08079000-0808c000 rw-p 08079000 00:00 0 08a20000-08a67000 rw-p 08a20000 00:00 0 b7f8d000-b7ff2000 rw-p b7f8d000 00:00 0 b7ffd000-b7ffe000 rw-p b7ffd000 00:00 0 bfa6d000-bfa91000 rw-p bffda000 00:00 0 [stack] Would /etc/nsd/restart or kill -1 20077 solve the problem?

  Read the article

• Nginx Proxying to Multiple IP Addresses for CMS' Website Preview

  - by Matthew Borgman

  First-time poster, so bear with me. I'm relatively new to Nginx, but have managed to figure out what I've needed... until now. Nginx v1.0.15 is proxying to PHP-FPM v.5.3.10, which is listening at http://127.0.0.1:9000. [Knock on wood] everything has been running smoothly in terms of hosting our CMS and many websites. Now, we've developed our CMS and configured Nginx such that each supported website has a preview URL (e.g. http://[WebsiteID].ourcms.com/) where the site can be, you guessed it, previewed in those situations where DNS doesn't yet resolve to our server, etc. Specifically, we use Nginx's Map module (http://wiki.nginx.org/HttpMapModule) and a regular expression in the server_name of the CMS' server{ } block to 1) lookup a website's primary domain name from its preview URL and then 2) forward the request to the "matched" primary domain. The corresponding Nginx configuration: map $host $h { 123.ourcms.com www.example1.com; 456.ourcms.com www.example2.com; 789.ourcms.com www.example3.com; } and server { listen [OurCMSIPAddress]:80; listen [OurCMSIPAddress]:443 ssl; root /var/www/ourcms.com; server_name ~^(.*)\.ourcms\.com$; ssl_certificate /etc/nginx/conf.d/ourcms.com.chained.crt; ssl_certificate_key /etc/nginx/conf.d/ourcms.com.key; location / { proxy_pass http://127.0.0.1/; proxy_set_header Host $h; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } (Note: I do realize that the regex in the server_name should be "tighter" for security reasons and match only the format of the website ID (i.e. a UUID in our case).) This configuration works for 99% of our sites... except those that have a dedicated IP address for an installed SSL certificate. A "502 Bad Gateway" is returned for these and I'm unsure as to why. This is how I think the current configuration works for any requests that match the regex (e.g. http://123.ourcms.com/): Nginx looks up the website's primary domain from the mapping, and as a result of the proxy_pass http://127.0.0.1 directive, passes the request back to Nginx itself, which since the proxied request has a hostname corresponding to the website's primary domain name, via the proxy_set_header Host $h directive, Nginx handles the request as if it was as direct request for that hostname. Please correct me if I'm wrong in this understanding. Should I be proxying to those website's dedicated IP addresses? I tried this, but it didn't seem to work? Is there a setting in the Proxy module that I'm missing? Thanks for the help. MB

  Read the article

• Sharing folder in a Virtual Private Windows Server 2008 R2 ?

  - by Triztian

  See Edit 2: Hello all, seems my involvement with computers has grown and I've found my self in the need to access a shared folder on a server. I've read some documentation and managed to set up the folder as a share, for this I created a local group and for now just one local user that has access to the share, the folder is in the public user folder and it's permissions should be (and I believe they are) read/write. The problem is that I can't connect from a remote machine I mean I don't know how the way it should be accessed, the server has a public IP and we use it also as a host to our website I don't know if that affects it though, the folder will be used as the "keeper" for the QuickBooks company files and has the database server manager installed. I've tried setting up a VPN Connection to the but no success. The server has a domain name a "http://www.example.com" that redirects to our website, I am unsure if it could be accessed that way, also the share has a location displayed when I right-click properties Heres what I've tried Setting up a VPN Connection (Windows Vista and 7) Got to the point where I got asked for credential and entered the user I created (which is not an admin) but I got a "Connection fail error 800" I suppose this is because in the domain field I entered the servers workgroup. right-click add network connection (Windows 7) Went through the wizard until I reached the point of entering the location, tried many things, the name in the share's properties(\\SOMETHING\Share), the http://www.example.com , the IP address I'm quite unfamiliar with this, so I have my guesses: Since the group and user are local they do not have access to the folder. The firewall in the server is blocking my connection. Anyways, any help and guidence is truly appreciated. EDIT 1: As @tony roth pointed out it may be a security fail, an I commented it out to management and said that that is not an issue, so please bare with me. EDIT 2: I've found out that the real question could be streamlined to "Sharing folder in a Virtual Private Server?", as thats what we have, a virtual private windows server 2008 R2, and I would like to know how to make it show like a normal folder in the client computer. Thanks again for all of your support.

  Read the article

• How to keep group-writeable shares on Samba with OSX clients?

  - by Oliver Salzburg

  I have a FreeNAS server on a network with OSX and Windows clients. When the OSX clients interact with SMB/CIFS shares on the server, they are causing permission problems for all other clients. Update: I can no longer verify any answers because we abandoned the project, but feel free to post any help for future visitors. The details of this behavior seem to also be dependent on the version of OSX the client is running. For this question, let's assume a client running 10.8.2. When I mount the CIFS share on an OSX client and create a new directory on it, the directory will be created with drwxr-x-rx permissions. This is undesirable because it will not allow anyone but me to write to the directory. There are other users in my group which should have write permissions as well. This behavior happens even though the following settings are present in smb.conf on the server: [global] create mask= 0666 directory mask= 0777 [share] force directory mode= 0775 force create mode= 0660 I was under the impression that these settings should make sure that directories are at least created with rwxrwxr-x permissions. But, I guess, that doesn't stop the client from changing the permissions after creating the directory. When I create a folder on the same share from a Windows client, the new folder will have the desired access permissions (rwxrwxrwx), so I'm currently assuming that the problem lies with the OSX client. I guess this wouldn't be such an issue if you could easily change the permissions of the directories you've created, but you can't. When opening the directory info in Finder, I get the old "You have custom access" notice with no ability to make any changes. I'm assuming that this is caused because we're using Windows ACLs on the share, but that's just a wild guess. Changing the write permissions for the group through the terminal works fine, but this is unpractical for the deployment and unreasonable to expect from anyone to do. This is the complete smb.conf: [global] encrypt passwords = yes dns proxy = no strict locking = no read raw = yes write raw = yes oplocks = yes max xmit = 65535 deadtime = 15 display charset = LOCALE max log size = 10 syslog only = yes syslog = 1 load printers = no printing = bsd printcap name = /dev/null disable spoolss = yes smb passwd file = /var/etc/private/smbpasswd private dir = /var/etc/private getwd cache = yes guest account = nobody map to guest = Bad Password obey pam restrictions = Yes # NOTE: read smb.conf. directory name cache size = 0 max protocol = SMB2 netbios name = freenas workgroup = COMPANY server string = FreeNAS Server store dos attributes = yes hostname lookups = yes security = user passdb backend = ldapsam:ldap://ldap.company.local ldap admin dn = cn=admin,dc=company,dc=local ldap suffix = dc=company,dc=local ldap user suffix = ou=Users ldap group suffix = ou=Groups ldap machine suffix = ou=Computers ldap ssl = off ldap replication sleep = 1000 ldap passwd sync = yes #ldap debug level = 1 #ldap debug threshold = 1 ldapsam:trusted = yes idmap uid = 10000-39999 idmap gid = 10000-39999 create mask = 0666 directory mask = 0777 client ntlmv2 auth = yes dos charset = CP437 unix charset = UTF-8 log level = 1 [share] path = /mnt/zfs0 printable = no veto files = /.snap/.windows/.zfs/ writeable = yes browseable = yes inherit owner = no inherit permissions = no vfs objects = zfsacl guest ok = no inherit acls = Yes map archive = No map readonly = no nfs4:mode = special nfs4:acedup = merge nfs4:chown = yes hide dot files force directory mode = 0775 force create mode = 0660

  Read the article

• batch file infinite loop when parsing file

  - by Bart

  Okay, this should be a really simple task but its proving to be more complicated than I think it should be. I'm clearly doing something wrong, and would like someone else's input. What I would like to do is parse through a file containing paths to directories and set permissions on those directories. An example line of the input file. There are several lines, all formatted the same way, with a different path to a directory. E:\stuff\Things\something else (X)\ (The file in question is generated under Cygwin using find to list all directories with "(X)" in the name. The file is then passed through unix2win to make it windows compatible. I've also tried manually creating the input file from within windows to rule out the file's creation method as the problem.) Here's where I'm stuck... I wrote the following quick and dirty batch file in Windows XP and it worked without any issues at all, but it will not work in server 2k8. Batch file code to run through the file and set permissions: FOR /F "tokens=*" %%A IN (dirlist.txt) DO echo y| cacls "%%A" /T /C /G "Domain Admins":f "Some Group":f "some-security-group":f What this is SUPPOSED to do (and does in XP) is loop through the specified file (dirlist.txt) and run cacls.exe on each directory it pulls from the file. The "echo y|" is in there to automagically confirm when cacls helpfully asks "are you sure?" for every directory in the list. Unfortunately, however, what it DOES is fall into an infinite loop. I've tried surrounding everything after "DO" with quotes, which prevents the endless loop but confuses cacls so it throws an error. Interestingly, I've tried running the code from after "DO" manually (obviously replacing the variable with the full path, copied straight from the file) at a command prompt and it runs as expected. I don't think it's the file or the loop, as adding quotes to the command to be executed prevents the loop from continuing past where it's supposed to... I really have no idea at this point. Any help would be appreciated. I have a feeling it's going to be something increadibly stupid... but I'm pulling my hair out so I thought I'd ask.

  Read the article

• Routing and Remote Access Service won't start after full disk

  - by NKCSS

  The HDD of the server was out of disk space, and after a reboot, RRAS won't start anymore on my 2008 R2 server. Error Details: Log Name: System Source: RemoteAccess Date: 2/5/2012 9:39:52 PM Event ID: 20153 Task Category: None Level: Error Keywords: Classic User: N/A Computer: Windows14111.<snip> Description: The currently configured accounting provider failed to load and initialize successfully. The connection was prevented because of a policy configured on your RAS/VPN server. Specifically, the authentication method used by the server to verify your username and password may not match the authentication method configured in your connection profile. Please contact the Administrator of the RAS server and notify them of this error. Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="RemoteAccess" /> <EventID Qualifiers="0">20153</EventID> <Level>2</Level> <Task>0</Task> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2012-02-05T20:39:52.000Z" /> <EventRecordID>12148869</EventRecordID> <Channel>System</Channel> <Computer>Windows14111.<snip></Computer> <Security /> </System> <EventData> <Data>The connection was prevented because of a policy configured on your RAS/VPN server. Specifically, the authentication method used by the server to verify your username and password may not match the authentication method configured in your connection profile. Please contact the Administrator of the RAS server and notify them of this error.</Data> <Binary>2C030000</Binary> </EventData> </Event> I think it has something to do with a corrupt config file, but I am unsure of what to do. I Removed the RRAS role, rebooted, and re-added, but it keeps failing with the same error. Thanks in advance. [UPDATE] If i set the accounting provider from 'Windows' to '' the service starts but VPN won't work. Any ideas how this can be repaired?

  Read the article

• Firefox can't establish a connection to the server at www.google.com

  - by Tom

  My home page in Firefox [v4.0] and Internet Explorer [v9.0.8112.16421, Update Versions RTM (KB982861)] is currently set to Google but when I depress the quick start icon to start up either browser, I am getting the following immediate results: Unable to connect (In Firefox) Firefox can't establish a connection to the server at www.google.com. The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer's network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web. Internet Explorer cannot display the webpage What you can try: Diagnose Connection Problems More information This problem can be caused by a variety of issues, including: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. There might be a typing error in the address. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. For offline users You can still view subscribed feeds and some recently viewed webpages. To view subscribed feeds: Click the Favorites button , click Feeds, and then click the feed you want to view. To view recently visited webpages (might not work on all pages): Press Alt, click File, and then click Work Offline. Click the Favorites button, click History, and then click the page you want to view. Thankfully, I am able to use one browser that I have installed on my computer (Mathon v3.0.20.5000) to search online for technical assistance in this matter. I have seen several WinSock error issues mentioned; but, they are pointing to Windows XP and I am using Windows 7 Pro and remain uncertain whether anything identified as a fix for one OS will work in another. Things I've tried: HiJackThis Complete scan with Avira AntiVirus Premium. What am I overlooking? What should I do to address this problem?

  Read the article

• Why are USB 2.0 devices crashing my system?

  - by BenAlabaster

  Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic baby-ATX motherboard with no identifying markings. CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. There's one stamp on the motherboard that says "Rev.B". On board it has 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. It has an 80Gb Western Digital hard drive freshly formatted and built with Windows XP Professional with Service Pack 3 and all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 crashes the machine as soon as it starts up). It's got a Daytek MV150 15" touch screen running through the VGA and COM1 with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem If I hook any USB 2.0 devices to this machine, it hangs the whole machine and I have to hard boot it to get it back up. Workarounds found I can plug the same devices into the on board USB 1.0 connectors and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions I've tried disabling all the on board devices that I'm not using - such as the on board LAN, the second COM port, the AGP connector etc. through the BIOS in an (perhaps misguided or futile) attempt to reduce the power consumption... I don't think it had any effect but it didn't do any harm. I was wondering if the PSU wattage just isn't enough to drive the USB 2.0 devices; I've seen this suggested but haven't found any confirmation that this could really be an issue - nor have I found a way to work around this issue - if indeed it is one. Any ideas? The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference. I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself. Other thoughts Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine?

  Read the article

• Do hard drive enclosures fail/is it the HDD or enclosure?

  - by x0a

  I'm having a whole host of problems with an external hard drive that was working just fine a couple of hours ago. I've had this problem before once, and that was about 3 months ago, here's what I documented: So a couple of hours ago I turned off all my computers and shut off the power to all my devices in my room, then went and turned the power off at the main switch so I could change an outlet. A couple hours later, after I've already slowly turned everything back on, I go to my xbox to try and watch a movie and it can't seem to list any of the movies I've got. So I go to my desktop to find that my external hard drive isn't there.. even though it's on and connected. It's also stationary and hidden behind something so there's not a whole lot of tampering/physical wear to that external. I plug it into my laptop to try and see what's going on. It starts making this endless loud screeching noise. None of that clicking that's usually associated with hd damage. It's not listed in my computers, and it shows up in Disk Management as "uninitialized" asking me to choose between two different partition types. After carefully disconnecting it and connecting it back, it asks me to format it, which I cancel. I start googling about my issue, starting to accept the situation, torn as hell and helpless and just about ready to toss the thing. Suddenly the screeching stops, after almost 45 minutes of it going, and Disk Management lists the drive as "Online" and "Healthy". Explorer pops up with all my files! I'm still being really careful with it and weary and treating it as though it's in fragile shape. I've downloaded some S.M.A.R.T. software to read the values and everything is listed as "OK" . No reallocated sectors, no read errors, no seek errors. I also ran a quick self-test, which completed without error. Everything seems fine. It looks to be a perfectly healthy external hard drive. So what the hell was that about? Was it doing some sort of maintenance or self-test? How am I supposed to tell the difference? I would've undoubtedly killed the drive for sure if had it gone on a bit longer. I've got the same problem now, with one exception: it doesn't magically reappear after the screeching stops. Occasionally I manage to get some S.M.A.R.T. diagnostics information, which basically reads everything as fine. The only problem is that my HD isn't initializing (so I can't access anything in it). I'm able to successfully run a quick smart test but not an extended one (I've only tried it once but got conflicting indications as to whether it was actually making any progress or not (was stuck on Random read test). So, final question (if all else fails): Could the hard drive enclosure be failing rather than the HDD? Is this a likely possibility at all? How would I know?

  Read the article

• How to set up a file server in a restricted corporate environment

  - by Emilio M Bumachar

  I work in a big corporation, and the disk space my team gets in the corporate file server is so low, I am considering turning my work PC into a file server. I ask this community for links to tutorials, software suggestions, and advice in general about how to set it up. My machine is an Intel Core2Duo E7500 @ 3GHz, 3 GB of RAM, Running Windows XP Service Pack 3. Upgrading, formatting or installing another OS is out of the question. But I do have Administrator priviledges on the PC, and I can install programs (at least for now). A lot of security software I don't even know about is and must remain installed. But I only need communication whithin the corporate network, which is not restricted. People have usernames (logins) on the corporate network, and I need to use them to restrict access. Simply put, I have a list of logins of team members, and only people in the list should access the files. I have about 150 GB of free disk space. I'm thinking of allocating 100 GB to the team's shared files. I plan monthly backups on machines of co-workers, same configuration. But automation of backups is a nice, unnecessary feature: it's totally acceptable for me to manually copy the contents to a different machine once a month. Uptime is important, as everyone would use these files in their daily work. I have experience as a python and C programmer, but no experience whatsoever as a sysadmin, and almost nothing of my programming experience is network programming. I'm a complete beginner in this. Thanks in advance for any help. EDIT I honestly appreciate all the warnings, I really do, but what I plan to make available is mostly stuff that now is solely on DVDs just for space reasons. It's 'daily work' to read them, but 'daily work write' files will remain on the corporate server. As for the importance of uptime, I think I overstated it: a few outages are OK, it's already an improvement over getting the DVDs. As for policy, my manager is kind of on my side, I will confirm that before making my move. As for getting more space through the proper channels, well, that was Plan A, and it's still on the table... But I don't have much hope. I'm not as "core businees" as I'd like.

  Read the article

< Previous Page | 585 586 587 588 589 590 591 592 593 594 595 596  | Next Page >