Search Results

Search found 2815 results on 113 pages for 'flow charts'.

Page 59/113 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

• Tunnel is up but cannot ping directly connected network

  - by drmanalo

  We configured a site-to-site VPN and here is the topology. I control the network on the left but not the one on the right. All devices in our network has public IPs. Server---ASA5505---Cisco887======Internet=====ASA5510---devices I can see the tunnel is up and can do extended ping using a loopback interface. From the 10.175 and 10.165 networks, they can also ping my loopback address. I can also dial in using a Cisco VPN client, and can connect to the devices on the right. #show crypto session Crypto session current status Interface: Vlan3 Profile: xxx-profile Session status: UP-ACTIVE Peer: 213.121.x.x port 500 IKEv1 SA: local 77.245.x.x/500 remote 213.121.x.x/500 Active IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.175.0.0/255.255.128.0 Active SAs: 0, origin: crypto map IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.165.0.0/255.255.192.0 Active SAs: 2, origin: crypto map #ping 10.165.29.39 source loopback 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.165.29.39, timeout is 2 seconds: Packet sent with a source address of 10.0.20.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 16/17/20 ms My problem is the devices on the right cannot reach my server. They could only ping the loopback address and nothing else. I'm pasting some diagnostics related to routing thinking perhaps routing is my issue. I can paste all the running-config on my side of network if needed. #show ip int brief Interface IP-Address OK? Method Status Protocol ATM0 unassigned YES NVRAM administratively down down Ethernet0 unassigned YES NVRAM administratively down down FastEthernet0 unassigned YES unset up up connected to ASA FastEthernet1 unassigned YES unset administratively down down FastEthernet2 unassigned YES unset administratively down down FastEthernet3 unassigned YES unset up up Loopback1 10.0.20.65 YES NVRAM up up Loopback2 10.0.20.1 YES NVRAM up up Virtual-Template1 77.245.x.x YES unset up down Virtual-Template2 77.245.x.x YES unset up down Vlan1 unassigned YES unset down down Vlan3 77.245.x.x YES NVRAM up up connected to the Internet #show run | section ip route ip route 0.0.0.0 0.0.0.0 77.245.x.x ip route 213.121.240.36 255.255.255.255 Vlan3 #show access-list Extended IP access list 102 10 permit ip 10.0.20.0 0.0.0.15 10.175.0.0 0.0.127.255 (3332 matches) 20 permit ip 10.0.20.0 0.0.0.15 10.165.0.0 0.0.63.255 (3498 matches) #show vlan-switch VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active 3 VLAN0003 active Fa0, Fa1, Fa2, Fa3 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup #show ip route Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP + - replicated route, % - next hop override Gateway of last resort is 77.245.x.x to network 0.0.0.0 S* 0.0.0.0/0 [1/0] via 77.245.x.x 10.0.0.0/8 is variably subnetted, 5 subnets, 3 masks C 10.0.20.0/28 is directly connected, Loopback2 L 10.0.20.1/32 is directly connected, Loopback2 C 10.0.20.64/28 is directly connected, Loopback1 L 10.0.20.65/32 is directly connected, Loopback1 S 10.165.0.0/18 [1/0] via 213.121.x.x 77.0.0.0/8 is variably subnetted, 3 subnets, 3 masks S 77.0.0.0/8 [1/0] via 77.245.x.x C 77.245.x.x/29 is directly connected, Vlan3 L 77.245.x.x/32 is directly connected, Vlan3 213.121.x.0/32 is subnetted, 1 subnets S 213.121.x.x is directly connected, Vlan3 I read some of the posts here which lead to NATing issue but I'not sure of my next step. Should I translate my public address to private and route it to the loopback address? (only guessing) CISCO VPN site to site Site-to-Site VPN between two ASA 5505s only working in one direction Hope someone could help. Thanks in advance!

  Read the article

• The new workflow management of Oracle´s Hyperion Planning: Define more details with Planning Unit Hierarchies and Promotional Paths

  - by Alexandra Georgescu

  After having been almost unchanged for several years, starting with the 11.1.2 release of Oracle´s Hyperion Planning the Process Management has not only got a new name: “Approvals” now is offering the possibility to further split Planning Units (comprised of a unique Scenario-Version-Entity combination) into more detailed combinations along additional secondary dimensions, a so called Planning Unit Hierarchy, and also to pre-define a path of planners, reviewers and approvers, called Promotional Path. I´d like to introduce you to changes and enhancements in this new process management and arouse your curiosity for checking out more details on it. One reason of using the former process management in Planning was to limit data entry rights to one person at a time based on the assignment of a planning unit. So the lowest level of granularity for this assignment was, for a given Scenario-Version combination, the individual entity. Even if in many cases one person wasn´t responsible for all data being entered into that entity, but for only part of it, it was not possible to split the ownership along another additional dimension, for example by assigning ownership to different accounts at the same time. By defining a so called Planning Unit Hierarchy (PUH) in Approvals this gap is now closed. Complementing new Shared Services roles for Planning have been created in order to manage set up and use of Approvals: The Approvals Administrator consisting of the following roles: Approvals Ownership Assigner, who assigns owners and reviewers to planning units for which Write access is assigned (including Planner responsibilities). Approvals Supervisor, who stops and starts planning units and takes any action on planning units for which Write access is assigned. Approvals Process Designer, who can modify planning unit hierarchy secondary dimensions and entity members for which Write access is assigned, can also modify scenarios and versions that are assigned to planning unit hierarchies and can edit validation rules on data forms for which access is assigned. (this includes as well Planner and Ownership Assigner responsibilities) Set up of a Planning Unit Hierarchy is done under the Administration menu, by selecting Approvals, then Planning Unit Hierarchy. Here you create new PUH´s or edit existing ones. The following window displays: After providing a name and an optional description, a pre-selection of entities can be made for which the PUH will be defined. Available options are: All, which pre-selects all entities to be included for the definitions on the subsequent tabs None, manual entity selections will be made subsequently Custom, which offers the selection for an ancestor and the relative generations, that should be included for further definitions. Finally a pattern needs to be selected, which will determine the general flow of ownership: Free-form, uses the flow/assignment of ownerships according to Planning releases prior to 11.1.2 In Bottom-up, data input is done at the leaf member level. Ownership follows the hierarchy of approval along the entity dimension, including refinements using a secondary dimension in the PUH, amended by defined additional reviewers in the promotional path. Distributed, uses data input at the leaf level, while ownership starts at the top level and then is distributed down the organizational hierarchy (entities). After ownership reaches the lower levels, budgets are submitted back to the top through the approval process. Proceeding to the next step, now a secondary dimension and the respective members from that dimension might be selected, in order to create more detailed combinations underneath each entity. After selecting the Dimension and a Parent Member, the definition of a Relative Generation below this member assists in populating the field for Selected Members, while the Count column shows the number of selected members. For refining this list, you might click on the icon right beside the selected member field and use the check-boxes in the appearing list for deselecting members. -------------------------------------------------------------------------------------------------------- TIP: In order to reduce maintenance of the PUH due to changes in the dimensions included (members added, moved or removed) you should consider to dynamically link those dimensions in the PUH with the dimension hierarchies in the planning application. For secondary dimensions this is done using the check-boxes in the Auto Include column. For the primary dimension, the respective selection criteria is applied by right-clicking the name of an entity activated as planning unit, then selecting an item of the shown list of include or exclude options (children, descendants, etc.). Anyway in order to apply dimension changes impacting the PUH a synchronization must be run. If this is really necessary or not is shown on the first screen after selecting from the menu Administration, then Approvals, then Planning Unit Hierarchy: under Synchronized you find the statuses Yes, No or Locked, where the last one indicates, that another user is just changing or synchronizing the PUH. Select one of the not synchronized PUH´s (status No) and click the Synchronize option in order to execute. -------------------------------------------------------------------------------------------------------- In the next step owners and reviewers are assigned to the PUH. Using the icons with the magnifying glass right besides the columns for Owner and Reviewer the respective assignments can be made in the ordermthat you want them to review the planning unit. While it is possible to assign only one owner per entity or combination of entity+ member of the secondary dimension, the selection for reviewers might consist of more than one person. The complete Promotional Path, including the defined owners and reviewers for the entity parents, can be shown by clicking the icon. In addition optional users might be defined for being notified about promotions for a planning unit. -------------------------------------------------------------------------------------------------------- TIP: Reviewers cannot change data, but can only review data according to their data access permissions and reject or promote planning units. -------------------------------------------------------------------------------------------------------- In order to complete your PUH definitions click Finish - this saves the PUH and closes the window. As a final step, before starting the approvals process, you need to assign the PUH to the Scenario-Version combination for which it should be used. From the Administration menu select Approvals, then Scenario and Version Assignment. Expand the PUH in order to see already existing assignments. Under Actions click the add icon and select scenarios and versions to be assigned. If needed, click the remove icon in order to delete entries. After these steps, set up is completed for starting the approvals process. Start, stop and control of the approvals process is now done under the Tools menu, and then Manage Approvals. The new PUH feature is complemented by various additional settings and features; some of them at least should be mentioned here: Export/Import of PUHs: Out of Office agent: Validation Rules changing promotional/approval path if violated (including the use of User-defined Attributes (UDAs)): And various new and helpful reviewer actions with corresponding approval states. About the Author: Bernhard Kinkel started working for Hyperion Solutions as a Presales Consultant and Consultant in 1998 and moved to Hyperion Education Services in 1999. He joined Oracle University in 2007 where he is a Principal Education Consultant. Based on these many years of working with Hyperion products he has detailed product knowledge across several versions. He delivers both classroom and live virtual courses. His areas of expertise are Oracle/Hyperion Essbase, Oracle Hyperion Planning and Hyperion Web Analysis.

  Read the article

• Blend for Visual Studio 2013 Prototyping Applications with SketchFlow

  - by T

  Originally posted on: http://geekswithblogs.net/tburger/archive/2014/08/10/blend-for-visual-studio-2013-prototyping-applications-with-sketchflow.aspxSketchFlow enables rapid creating of dynamic interface mockups very quickly. The SketchFlow workspace is the same as the standard Blend workspace with the inclusion of three panels: the SketchFlow Feedback panel, the SketchFlow Animation panel and the SketchFlow Map panel. By using SketchFlow to prototype, you can get feedback early in the process. It helps to surface possible issues, lower development iterations, and increase stakeholder buy in. SketchFlow prototypes not only provide an initial look but also provide a way to add additional ideas and input and make sure the team is on track prior to investing in complete development. When you have completed the prototyping, you can discard the prototype and just use the lessons learned to design the application from or extract individual elements from your prototype and include them in the application. I don’t recommend trying to transition the entire project into a development project. Objects that you add with the SketchFlow style have a hand-sketched look. The sketch style is used to remind stakeholders that this is a prototype. This encourages them to focus on the flow and functionality without getting distracted by design details. The sketchflow assets are under sketchflow in the asset panel and are identifiable by the postfix “–Sketch”. For example “Button-Sketch”. You can mix sketch and standard controls in your interface, if required. Be creative, if there is a missing control or your interface has a different look and feel than the out of the box one, reuse other sketch controls to mimic the functionality or look and feel. Only use standard controls if it doesn’t distract from the idea that this is a prototype and not a standard application. The SketchFlow Map panel provides information about the structure of your application. To create a new screen in your prototype: Right-click the map surface and choose “Create a Connected Screen”. Name the screens with names that are meaningful to the stakeholders. The start screen is the one that has the green arrow. To change the start screen, right click on any other screen and set to start screen. Only one screen can be the start screen at a time. Rounded screen are component screens to mimic reusable custom controls that will be built into the final application. You can change the colors of all of the boxes and should use colors to create functional groupings. The groupings can be identified in the SketchFlow Project Settings. To add connections between screens in the SketchFlow Map panel. Move the mouse over a screen in the SketchFlow and a menu will appear at the bottom of the screen node. In the menu, click Connect to an existing screen. Drag the arrow to another screen on the Map. You add navigation to your prototype by adding connections on the SketchFlow map or by adding navigation directly to items on your interface. To add navigation from objects on the artboard, right click the item then from the menu, choose “Navigate to”. This will expose a sub-menu with available screens, backward, or forward. When the map has connected screens, the SketchFlow Player displays the connected screens on the Navigate sidebar. All screens show in the SketchFlow Player Map. To see the SketchFlow Player, run your SketchFlow prototype. The Navigation sidebar is meant to show the desired user work flow. The map can be used to view the different screens regardless of suggested navigation in the navigation bar. The map is able to be hidden and shown. As mentioned, a component screen is a shared screen that is used in more than one screen and generally represents what will be a custom object in the application. To create a component screen, you can create a screen, right click on it in the SketchFlow Map and choose “Make into component screen”. You can mouse over a screen and from the menu that appears underneath, choose create and insert component screen. To use an existing screen, select if from the Asset panel under SketchFlow, Components. You can use Storyboards and Visual State animations in your SketchFlow project. However, SketchFlow also offers its own animation technique that is simpler and better suited for prototyping. The SketchFlow Animation panel is above your artboard by default. In SketchFlow animation, you create frames and then position the elements on your interface for each frame. You then specify elapsed time and any effects you want to apply to the transition. The + at the top is what creates new frames. Once you have a new Frame, select it and change the property you want to animate. In the example above, I changed the Text of the result box. You can adjust the time between frames in the lower area between the frames. The easing and effects functions are changed in the center between each frame. You edit the hold time for frames by clicking the clock icon in the lower left and the hold time will appear on each frame and can be edited. The FluidLayout icon (also located in the lower left) will create smooth transitions. Next to the FluidLayout icon is the name of that Animation. You can rename the animation by clicking on it and editing the name. The down arrow chevrons next to the name allow you to view the list of all animations in this prototype and select them for editing. To add the animation to the interface object (such as a button to start the animation), select the PlaySketchFlowAnimationAction from the SketchFlow behaviors in the Assets menu and drag it to an object on your interface. With the PlaySketchFlowAnimationAction that you just added selected in the Objects and Timeline, edit the properties to change the EventName to the event you want and choose the SketchFlowAnimation you want from the drop down list. You may want to add additional information to your screens that isn’t really part of the prototype but is relevant information or a request for clarification or feedback from the reviewer. You do this with annotations or notes. Both appear on the user interface, however, annotations can be switched on or off at design and review time. Notes cannot be switched off. To add an Annotation, chose the Create Annotation from the Tools menu. The annotation appears on the UI where you will add the notes. To display or Hide annotations, click the annotation toggle at the bottom right on the artboard . After to toggle annotations on, the identifier of the person who created them appears on the artboard and you must click that to expand the notes. To add a note to the artboard, simply select the Note-Sketch from Assets ->SketchFlow ->Styles ->Sketch Styles. Drag and drop it to the artboard and place where you want it. When you are ready for users to review the prototype, you have a few options available. Click File -> Export and choose one of the options from the list: Publish to Sharepoint, Package SketchFlowProject, Export to Microsoft Word, or Export as Images. I suggest you play with as many of the options as you can to see what they do. Both the Sharepoint and Packaged SketchFlowProject allow you to collect feedback from one or more users that you can import into the project. The user can make notes on the UI and in the Feedback area in the bottom left corner of the player. When the user is done adding feedback, it is exported from the right most folder icon in the My Feedback panel. Feeback is imported on a panel named SketchFlow Feedback. To get that panel to show up, select Window -> SketchFlow Feedback. Once you have the panel showing, click the + in the upper right of the panel and find the notes you exported. When imported, they will show up in a list and on the artboard. To document your prototype, use the Export to Microsoft Word option from the File menu. That should get you started with prototyping.

  Read the article

• Looping to provide multiple lines in linechart (django-googlecharts)

  - by mighty_bombero

  Hi, I'm trying to generate some charts using django-googlecharts. This works fine for rather static data but in one case I would like to render a different number of lines, based on a variable. I tried this: {% chart %} {% for line in line_data %} {% chart-data line %} {% endfor %} {% chart-size "390x200" %} {% chart-type "line" %} {% chart-labels days %} {% endchart %} Line data is a list containing lists. The template code fails with "Caught an exception while rendering: max() arg is an empty sequence". I guess the problem is that I try to loop over templatetags. What approach could be used here? Or am I completely missing something? Is this doable using inclusion tags? Thanks for your help.

  Read the article

• Annotating axis in ggplot2

  - by mpiktas

  I am looking for the way to annotate axis in ggplot2. The example of the problem can be found here: http://learnr.wordpress.com/2009/09/24/ggplot2-back-to-back-bar-charts. The y axis of the chart (example graph in the link) has an annotation: (million euro). Is there a way to create such types of annotations in ggplot2? Looking at the documentation there is no obvious way, since the ggplot does not explicitly let you put objects outside plotting area. But maybe there is some workaround? One of the possible workarounds I thought about is using scales: data=data.frame(x=1:10,y=1:10) qplot(x=x,y=y,data=data)+scale_y_continuous(breaks=10.1,label="Millions") But then how do I remove the tick? And it seems that since ggplot does not support multiple scales, I will need to grab the output of the scale_y_continuous, when it calculates the scales automaticaly and then add my custom break and label by hand. Maybe there is a better way?

  Read the article

• Flowcharting tool/add-in for Visual Studio

  - by Rajah

  A 2 part question: Are flow-charts, as tool to analyze source-code, no longer considered useful? The reason I ask this question is that if you Google for source-code to flowchart tools for Visual Studio, there are no relevant results. Also, Microsoft does not seem to have a tool for this purpose. Are people just not using flowcharts that much any more? (I find them to be a great way to document complex logic in my code). Are there any VS tools that can take .Net (C#, VB.Net) code and convert it to a flowchart? (The only tool that I found is Aviosto's Visustin, which does not provide VS integration). Any other tools that you can recommend for this purpose?

  Read the article

• Does there exist a jQuery plugin or JavaScript library that allows Venn Diagram presentation?

  - by knowncitizen

  I'm writing a jQuery application to allow analysis of data with the help of visual cues. My data is retrieved via XMLHttpRequest in the form of JSON. The visual cues include histograms, spark lines, and various other graph types. The idea is that the user is able to narrow their data via these various visual views. My question is thus - aside from the Google Charts API, does there exist a JavaScript way of presenting a Venn Diagram? Requirement: no Flash. Canvas is acceptable.

  Read the article

• Problem when loading image from google chart api URL

  - by user304839

  I want to show concentric charts of google api in iphone, but the imageData varible returns null value and image does not loaded from url to image view this is code: NSData *imageData = [[NSData alloc] initWithContentsOfURL:[NSURL URLWithString:@"http://chart.apis.google.com/chart?cht=pc&chd=t:120,45|120,60,50,70,60&chs=300x200&chl=||helo|wrd|india|pak|ban&chco=FFFFFF|FFFFFF,e72a28|a9d331|ffce08|8a2585|184a7d"]]; NSLog(@"%@",imageData); UIImage *myimage = [[UIImage alloc] initWithData:imageData]; self.myImageView.image=myimage; please any one help me to overcome on this problem

  Read the article

• top tweets WebLogic Partner Community – June 2013

  - by JuergenKress

  Send us your tweets @wlscommunity #WebLogicCommunity and follow us on twitter http://twitter.com/wlscommunity. Please feel free to send us your news! Lucas Jellema ?Getting started with Java EE 7: The Tutorial http://docs.oracle.com/javaee/7/tutorial/doc/home.htm … Simon Haslam I'm looking forward to starting a "WLS on ODA" proof of concept - some ideas for testing: http://www.veriton.co.uk/roller/fmw/entry/virtualised_oda_proof_of_concept … Frank Munz ?It's not too late - I just submitted two presentations about #OracleWebLogic and #Coherence for the @DOAGeV conference in Nürnberg. Did you? Arun Gupta ?Tyrus 1.0 User Guide: https://tyrus.java.net/documentation/1.0/user-guide.html … #WebSocket #JavaEE7 #GlassFish Arun Gupta #JavaEE7 Launch Webinar Technical Breakout replays on Youtube: http://bit.ly/12uUicT JSON 1.0 , EJB .2, Batch 1.0 more coming! OracleBlogs ?FREE Virtual Developer Day: Java SE, Java EE, Java Emebedded on Jun 19th and 25th http://ow.ly/2xBkwV Markus Eisele #Oracle #JavaSE Critical Patch Update Pre-Release Announcement - June 2013 http://www.oracle.com/technetwork/topics/security/javacpujun2013-1899847.html … #security OracleSupport_WLS ?Simple Custom #JMX MBeans with #WebLogic 12c and #Spring http://pub.vitrue.com/3kEr Oracle Technet Building Java HTML5/WebSocket Applications with JSR 356 - 4pm - Grand Ballroom Salon A/B #qconnewyork WebLogic Community Oracle Fusion Middleware (OFM) 11g (11.1.1.7) Starter Kit available & Customizable Demos http://wp.me/p1LMIb-BK Oracle Technet #Java EE 7: Moving Java Forward for the Enterprise | @java http://pub.vitrue.com/tHiM OTNArchBeat ?Oracle Forms to ADF Modernization Reference - Convero (AMEC) Project | @AndrejusB http://pub.vitrue.com/lZPR WebLogic Community ?ExaLogic In Memory Applications & Whitepapers Building Large Scale E-Commerce Platforms & Rethink the Entire Application Lifecycle… WebLogic Community ?Coherence YouTube videos http://wp.me/p1LMIb-BG Arun Gupta ?WARNING: Next 2 days are going to be loaded with #JavaEE7 launch related tweets, and offline next week! JDeveloper & ADF Using Contextual Event in Oracle ADF http://dlvr.it/3Vpybr Oracle WebLogic Check out new blog on #hybrid_cloud & why choice is important http://bit.ly/1b1QGhL Andrejus Baranovskis Oracle Forms to ADF Modernization Reference - Convero (AMEC) Project http://fb.me/1M9iWNmAw WebLogic Community WebLogic on Oracle Database Appliance by Frances Zhao http://wp.me/p1LMIb-BE OTNArchBeat ?New: A-Team Chronicles >> A great resource for technical content covering Oracle Fusion Middleware / Fusion Apps http://pub.vitrue.com/qbzS Oracle for Partners ?Take Java To The Edge: Java Virtual Developer Day – June 19 & June 25 http://bit.ly/19fGlSX Adam Bien ?Looking forward to tomorrow's #javaee7 + #angularjs #html5 marriage at #jpoint. See you there: http://www.jpoint.nl/meetingpoint/editie-2013#sessie-1 … shay shmeltzer ?There is a new patch for the #Oracle #ADF Mobile extension - use help->check for updates to get it. Frank Munz ?Not using @OracleWebLogic 12c yet? Australia does! Reviews from my @AUSOUG workshops in Brisbane, Adelaide and Perth. http://goo.gl/BfVc4 Arun Gupta ?WebSocket, Server-Sent Events, #JavaEE7 sessions accepted at #jaxlondon ... that's gonna be at least third trip to London this year! WebLogic Community SPARC T5-8 Delivers Best Single System SPECjEnterprise2010 Benchmark running WebLogic 12c http://wp.me/p1LMIb-BC WebLogic Community The Ultimate Java EE Event - 16 Power Workshops mit allen wichtigen Java-EE-Themen http://wp.me/p1LMIb-BY Oracle WebLogic ?@OracleWebLogic 7 Jun New Blog Post: Using try-with-resources with JDBC objects http://ow.ly/2xryb5 JDeveloper & ADF Switching Lists of Values http://dlvr.it/3PbCkw WebLogic Community ?YouTube channel Learning Oracle's ADF http://wp.me/p1LMIb-zA Markus Eisele [GER] RT @heisedc: #Java-Entwicklung in #Oracles Public #Cloud http://heise.de/-1866388/ftw OracleBlogs ?Coherence Incubator & Community Source Code & Release Documentation http://ow.ly/2x2fXK chriscmuir ?New blog post: Migrating ADF Mobile apps from 1.0 to 1.1 https://blogs.oracle.com/onesizedoesntfitall/entry/migrating_adf_mobile_apps_from … JDeveloper & ADF ?ADF JavaScript Partitioning for Performance http://dlvr.it/3Trw15 WebLogic Community WebLogic Server Security Workshop June 27th 2013 Germany http://wp.me/p1LMIb-C7 WebLogic Community Oracle Optimized Solution for WebLogic Server 12c http://wp.me/p1LMIb-BA WebLogic Community Virtualize and Run Your Forms Applications in the Cloud - Now On Demand http://wp.me/p1LMIb-By Lucas Jellema Innteresting presentation on various aspects of end user assistance in Fusion Applications (ADF based): http://www.slideshare.net/uobroin/ouag-ireland-final2012slideshare … Adam Bien ?Summer Of JavaEE Workshops And Gigs: Free Hacking night:11.06.2013, Utrecht JavaEE 7 Meets HTML 5 and AngularJ... http://bit.ly/11XRjt4 WebLogic Community ?Real World ADF Design & Architecture Principles Trainings Germany, Poland & Portugal http://wp.me/p1LMIb-Bw Oracle for Partners ?JAVA Virtual Developer Day – June 19 & June 25 - Watch educational content and engage with Oracle experts online https://oracle.6connex.com/portal/java2013/login/?langR=en_US&mcc=OPNNSL … Markus Eisele ?[blog] Java EE 7 is final. Thoughts, Insights and further Pointers. http://dlvr.it/3SrxnB #javaee7 WebLogic Community Oracle takes the top spot for market share in the Application Server Market Segment for 2012 http://wp.me/p1LMIb-Bu OTNArchBeat ?Oracle ACE Director @LucasJellema is "very pleasantly surprised" with the new ADF Academy. http://pub.vitrue.com/8fad chriscmuir ?Sell out crowd for our ADF architecture course in Munich #adfarch pic.twitter.com/zhNtQJ25JV Markus Eisele ?[blog] New German Article: Java 7 Update 21 Security Improvements http://dlvr.it/3Sc8V9 #java #heise #security Markus Eisele ?[blog] New German Article: Oracle Java Cloud Service http://dlvr.it/3Sc20V #java #heise #OracleCloud OracleSupport_WLS ?Troubleshooting and Tuning with #WebLogic - Developer Webcast now available on #Youtube http://pub.vitrue.com/GSOy Andrejus Baranovskis New ADF Academy - Impressive Concept for ADF eLearning http://fb.me/2kYSMKKR5 OracleSupport_WLS ?Removing a #weblogic domain properly http://pub.vitrue.com/ZndM WebLogic Community WebLogic Partner Community Newsletter May 2013 http://wp.me/p1LMIb-Bp Oracle WebLogic ?Blog: Troubleshooting tools Part 3- Heap Dumps #Oracle #WebLogic Read the series http://bit.ly/14CQSD2 Oracle WebLogic ?Blog: #WebLogic_Server on #Oracle_Database_Appliance- How to conjure a WebLogic cluster- http://bit.ly/11fciHA Oracle WebLogic ?Check out new cool features in Oracle Traffic Director- http://bit.ly/11fbz9h WebLogic Community Additional new material WebLogic Community April 2013 http://wp.me/p1LMIb-zM WebLogic Community New WebLogic references - we want yours http://wp.me/p1LMIb-zK OracleSupport_WLS ?#Weblogic Session Replication jsession ID and F5 http://pub.vitrue.com/dWZp OracleBlogs ?top tweets WebLogic Partner Community May 2013 http://ow.ly/2xc8M5 WebLogic Community Welcome to the Spring edition of Oracle Scene http://wp.me/p1LMIb-zE Andreas Koop ?[blog post] ADF: Static Values View Object does not show any values (solved) http://bit.ly/14RDZ8p OracleBlogs ?ADF Mobile - accessing the SQLite database http://ow.ly/2x85r0 OracleSupport_WLS Youtube channel- Troubleshooting and Tuning with #WebLogic.#JRockit #SOAP #JRF http://pub.vitrue.com/qMxu Arun Gupta Next Java Magazine is all about #JavaEE7...productivity, HTML5, WebSocket, Batch & more. Subscribe http://ow.ly/lkD5D (@Oraclejavamag) Oracle WebLogic How to configure a #WebLogic cluster on #Oracle_Database_Appliance? It’s easy, read how. http://bit.ly/11fciHA Oracle WebLogic ?Blog: How to use Heap Dumps to troubleshooting memory leaks- #Oracle #WebLogic_Server http://bit.ly/14CQSD2 OracleBlogs ?Over 100 Images To Be Added to NetBeans Platform Showcase http://ow.ly/2x7Fvp Lucas Jellema A new release of the ADF EMG Task Flow Tester is now available for both JDeveloper 11 R1 and R2. https://java.net/projects/adf-task-flow-tester/pages/GettingStarted … WebLogic Partner Community For regular information become a member in the WebLogic Partner Community please visit: http://www.oracle.com/partners/goto/wls-emea ( OPN account required). If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Mix Forum Wiki Technorati Tags: twitter,WebLogic,WebLogic Community,Oracle,OPN,Jürgen Kress

  Read the article

• Stable random color algorithm

  - by Olmo

  Here we have an interesting real-world algorithm requirement involving colors. 1) Nice random colors: In ordeeing to draw a beautifull chart (i.e: pie chart) we need to pick a random set of Colors that: a) are different enought b) Play nicely Doesnt Look hard. For example u fix bright and saturation and divide hue in steps of 360/Num_sectors 2) Stable: given Pie1 with sectors with labes ('A','B','C') and Pie2 with sector with labels ('B','C','D'), will be nice if color('B',pie1)= color('B',pie2) and the same for 'C' and so on, so people don't get crazy when seeing similar updated charts, even if some sectors appear some dissapeared or the number of sectors changed. The label is the only stable thing. 3) hard-coded colors: the algorithm allows hardcoded label-color relationships as an input but stills doing a good work (1 & 2) for the rest of free labels. I think this algorithm, even if it looks quite ad-hoc, will be usefull in more then one situation. Any ideas?

  Read the article

• Open source software

  - by Maurizio Reginelli

  What is your opinion about open source software? It is helpful in many situation, for example a community can correct many bugs. But I also think that it can be dangerous for a software developer. If you develop an application and share its source code, a lot of applications can grow with a little effort, simply copying part of your code. For example, if you develop a library in WPF which can be used to create charts, and share your code, this can be dangerous for companies which main business is WPF component developing. And obviously it is dangerous for a software developer who works in that company. What do you think about this?

  Read the article

• Stress Test tool for Password Protected Website

  - by Jason

  We need to run a stress test on a password protection section of a website we host. What tool (paid or free) would be best for us to use for this? We'd like to be able to create several 'scripts' and then have the stress test simulate X number of users. Each script will have us login as a specific user and then click on some links and submit forms to simulate an actual user. Ideally the software would also create some nice data exports/charts. Server is a linux web server, but we could run this on linux or Windows so software that will run on either is fine.

  Read the article

• How do I make "simple" throughput servlet-filter?

  - by Tommy

  I'm looking to create a filter that can give me two things: number of request pr minute, and average responsetime pr minute. I already got the individual readings, I'm just not sure how to add them up. My filter captures every request, and it records the time each request takes: public void doFilter(ServletRequest request, ...() { long start = System.currentTimeMillis(); chain.doFilter(request, response); long stop = System.currentTimeMillis(); String time = Util.getTimeDifferenceInSec(start, stop); } This information will be used to create some pretty Google Chart charts. I don't want to store the data in any database. Just a way to get current numbers out when requested As this is a high volume application; low overhead is essential. I'm assuming my applicationserver doesn't provide this information.

  Read the article

• R and SPSS difference

  - by sfactor

  i will be analysing vast amount of network traffic related data shortly. i will pre-process the data in order to analyse it. i have found that R and SPSS are among the most popular tools for statistical analysis. i will also be generating quite a lot of graphs and charts. so i was wondering what is the basic difference between these two softwares. i am not asking which one is better. i just wanted to know what are the difference in terms of workflow between the two besides the fact that SPSS has a GUI. I will be mostly working with scripts in either case anyway so i wanted to know about the other differences.

  Read the article

• How to store user preferences? Cookie becomes bigger..

  - by ari

  My application (Asp.Net MVC) has great interaction with the user interface (jQuery/js). For example, setting various searches charts, moving the gadgets on the screen and more .. I of course want to keep all data for each user. So that data will be available from any page in the Dumaine and the user will accepts his preferences. Now I keep all data in a cookie because it did not seem logical asynchronous access to the server each time the user changes something and thet happens a lot.When the user logout from the application I save the cookie to the database. The problem is the cookie becomes very large. The thought that this huge cookie is attached to each server request makes me feel that my attitude is wrong. Another problem cookies have size limit. It varies from your browser but I definitely have been close to the border - my cookie easily become 4kb Is there another solution?

  Read the article

• Plotting 3-tuple data points in a surface / contour plot using matplotlib

  - by morpheous

  I have some surface data that is generated by an external program as XYZ values. I want to create the following graphs, using matplotlib: Surface plot Contour plot Contour plot overlayed with a surface plot I have looked at several examples for plotting surfaces and contours in matplotlib - however, the Z values seems to be a function of X and Y i.e. Y ~ f(X,Y). I assume that I will somehow need to transform my Y variables, but I have not seen any example yet, that shows how to do this. So, my question is this: given a set of (X,Y,Z) points, how may I generate Surface and contour plots from that data? BTW, just to clarify, I do NOT want to create scatter plots. Also although I mentioned matplotlib in the title, I am not averse to using rpy(2), if that will allow me to create these charts.

  Read the article

• In Django how display all of the values aftere the for loop is finished instead of displaying them one by one

  - by Igor

  Hello, In my django project in the view I call the last 6 values in the column and send them to the template. I then would like to pass into google charts api those 6 values and have a graph. At the moment for some reason I get 6 different graphs. {% for foodbag in foodbags %} <img src="http://chart.apis.google.com/chart?chxl=0:|0|1|2|3|4|5|6&chxr=2,0,0&chxs=0,1,676767,10.5,1,l,676767|2,676767,5.5,0,l,676767&chxt=x,y&chs=300x170&cht=bvg&chco=76A4FB&chd=t:{{foodbag.12}},0&chma=0,5|5,5&chdlp=t&chtt=Food+Bags"/> {% endfor %} I'm not sure how to replace string chd=t:{{foodbag.12}}, with the 6 values I am trying to extract from foodbags. I would really appreciate the help. Thank you

  Read the article

• Project tracking/management tool

  - by Alvaro Rodriguez

  Which project tracking tool do you use? Does it allow programmers to bill hours worked to projects/tasks? Does it allow to track items promised vs. items delivered? Does it allow to forecast personnel needs when you have only a ballpark estimate of how many hours you are going to need for different task types? Does it integrate with your bug tracker? [Mantis] Does it integrate with your source control tool? [Subversion] Does it allow you to easily publish your schedule and current priorities to team members? Does it produce reports on any or all of the above? Am I even right in calling a tool that does those things a "Project tracking/management tool"? What does your tool have that makes you love it and use it every day? I don't really care about Gantt charts. I find Microsoft Project quite clunky for this needs (although I'm hardly an expert user).

  Read the article

• Invert bitmap colors

  - by Alex Orlov

  I have the following problem. I have a charting program, and it's design is black, but the charts (that I get from the server as images) are light (it actually uses only 5 colors: red, green, white, black and gray). To fit with the design inversion does a good job, the only problem is that red and green are inverted also (green - pink, red - green). Is there a way to invert everything except those 2 colors, or a way to repaint those colors after inversion? And how costly are those operations (since I get the chart updates pretty often)? Thanks in advance :) UPDATE I tried replacing colors with setPixel method in a loop for(int x = 0 ;x < chart.getWidth();x++) { for(int y = 0;y < chart.getHeight();y++) { final int replacement = getColorReplacement(chart.getPixel(x, y)); if(replacement != 0) { chart.setPixel(x, y, replacement); } } } Unfortunetely, the method takes too long (~650ms), is there a faster way to do it, and will setPixels() method work faster?

  Read the article

• Developing Schema Compare for Oracle (Part 1)

  - by Simon Cooper

  SQL Compare is one of Red Gate's most successful SQL Server tools; it allows developers and DBAs to compare and synchronize the contents of their databases. Although similar tools exist for Oracle, they are quite noticeably lacking in the usability and stability that SQL Compare is known for in the SQL Server world. We could see a real need for a usable schema comparison tools for Oracle, and so the Schema Compare for Oracle project was born. Over the next few weeks, as we come up to release of v1, I'll be doing a series of posts on the development of Schema Compare for Oracle. For the first post, I thought I would start with the main pitfalls that we stumbled across when developing the product, especially from a SQL Server background. 1. Schemas and Databases The most obvious difference is that the concept of a 'database' is quite different between Oracle and SQL Server. On SQL Server, one server instance has multiple databases, each with separate schemas. There is typically little communication between separate databases, and most databases are no more than about 1000-2000 objects. This means SQL Compare can register an entire database in a reasonable amount of time, and cross-database dependencies probably won't be an issue. It is a quite different scene under Oracle, however. The terms 'database' and 'instance' are used interchangeably, (although technically 'database' refers to the datafiles on disk, and 'instance' the running Oracle process that reads & writes to the database), and a database is a single conceptual entity. This immediately presents problems, as it is infeasible to register an entire database as we do in SQL Compare; in my Oracle install, using the standard recommended options, there are 63975 system objects. If we tried to register all those, not only would it take hours, but the client would probably run out of memory before we finished. As a result, we had to allow people to specify what schemas they wanted to register. This decision had quite a few knock-on effects for the design, which I will cover in a future post. 2. Connecting to Oracle The next obvious difference is in actually connecting to Oracle – in SQL Server, you can specify a server and database, and off you go. On Oracle things are slightly more complicated. SIDs, Service Names, and TNS A database (the files on disk) must have a unique identifier for the databases on the system, called the SID. It also has a global database name, which consists of a name (which doesn't have to match the SID) and a domain. Alternatively, you can identify a database using a service name, which normally has a 1-to-1 relationship with instances, but may not if, for example, using RAC (Real Application Clusters) for redundancy and failover. You specify the computer and instance you want to connect to using TNS (Transparent Network Substrate). The user-visible parts are a config file (tnsnames.ora) on the client machine that specifies how to connect to an instance. For example, the entry for one of my test instances is: SC_11GDB1 = (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = simonctest)(PORT = 1521)) ) (CONNECT_DATA = (SID = 11gR1db1) ) ) This gives the hostname, port, and SID of the instance I want to connect to, and associates it with a name (SC_11GDB1). The tnsnames syntax also allows you to specify failover, multiple descriptions and address lists, and client load balancing. You can then specify this TNS identifier as the data source in a connection string. Although using ODP.NET (the .NET dlls provided by Oracle) was fine for internal prototype builds, once we released the EAP we discovered that this simply wasn't an acceptable solution for installs on other people's machines. Due to .NET assembly strong naming, users had to have installed on their machines the exact same version of the ODP.NET dlls as we had on our build server. We couldn't ship the ODP.NET dlls with our installer as the Oracle license agreement prohibited this, and we didn't want to force users to install another Oracle client just so they can run our program. To be able to list the TNS entries in the connection dialog, we also had to locate and parse the tnsnames.ora file, which was complicated by users with several Oracle client installs and intricate TNS entries. After much swearing at our computers, we eventually decided to use a third party Oracle connection library from Devart that we could ship with our program; this could use whatever client version was installed, parse the TNS entries for us, and also had the nice feature of being able to connect to an Oracle server without having any client installed at all. Unfortunately, their current license agreement prevents us from shipping an Oracle SDK, but that's a bridge we'll cross when we get to it. 3. Running synchronization scripts The most important difference is that in Oracle, DDL is non-transactional; you cannot rollback DDL statements like you can on SQL Server. Although we considered various solutions to this, including using the flashback archive or recycle bin, or generating an undo script, no reliable method of completely undoing a half-executed sync script has yet been found; so in this case we simply have to trust that the DBA or developer will check and verify the script before running it. However, before we got to that stage, we had to get the scripts to run in the first place... To run a synchronization script from SQL Compare we essentially pass the script over to the SqlCommand.ExecuteNonQuery method. However, when we tried to do the same for an OracleConnection we got a very strange error – 'ORA-00911: invalid character', even when running the most basic CREATE TABLE command. After much hair-pulling and Googling, we discovered that Oracle has got some very strange behaviour with semicolons at the end of statements. To understand what's going on, we need to take a quick foray into SQL and PL/SQL. PL/SQL is not T-SQL In SQL Server, T-SQL is the language used to interface with the database. It has DDL, DML, control flow, and many other nice features (like Turing-completeness) that you can mix and match in the same script. In Oracle, DDL SQL and PL/SQL are two completely separate languages, with different syntax, different datatypes and different execution engines within the instance. Oracle SQL is much more like 'pure' ANSI SQL, with no state, no control flow, and only the basic DML commands. PL/SQL is the Turing-complete language, but can only do DML and DCL (i.e. BEGIN TRANSATION commands). Any DDL or SQL commands that aren't recognised by the PL/SQL engine have to be passed back to the SQL engine via an EXECUTE IMMEDIATE command. In PL/SQL, a semicolons is a valid token used to delimit the end of a statement. In SQL, a semicolon is not a valid token (even though the Oracle documentation gives them at the end of the syntax diagrams) . When you execute the command CREATE TABLE table1 (COL1 NUMBER); in SQL*Plus the semicolon on the end is a command to SQL*Plus to execute the preceding statement on the server; it strips off the semicolon before passing it on. SQL Developer does a similar thing. When executing a PL/SQL block, however, the syntax is like so: BEGIN INSERT INTO table1 VALUES (1); INSERT INTO table1 VALUES (2); END; / In this case, the semicolon is accepted by the PL/SQL engine as a statement delimiter, and instead the / is the command to SQL*Plus to execute the current block. This explains the ORA-00911 error we got when trying to run the CREATE TABLE command – the server is complaining about the semicolon on the end. This also means that there is no SQL syntax to execute more than one DDL command in the same OracleCommand. Therefore, we would have to do a round-trip to the server for every command we want to execute. Obviously, this would cause lots of network traffic and be very slow on slow or congested networks. Our first attempt at a solution was to wrap every SQL statement (without semicolon) inside an EXECUTE IMMEDIATE command in a PL/SQL block and pass that to the server to execute. One downside of this solution is that we get no feedback as to how the script execution is going; we're currently evaluating better solutions to this thorny issue. Next up: Dependencies; how we solved the problem of being unable to register the entire database, and the knock-on effects to the whole product.

  Read the article

• Orchestrating the Virtual Enterprise

  - by John Murphy

  During the American Industrial Revolution, the Ford Motor Company did it all. It turned raw materials into a showroom full of Model Ts. It owned a steel mill, a glass factory, and an automobile assembly line. The company was both self-sufficient and innovative and went on to become one of the largest and most profitable companies in the world. Nowadays, it's unusual for any business to follow this vertical integration model because its much harder to be best in class across such a wide a range of capabilities and services. Instead, businesses focus on their core competencies and outsource other business functions to specialized suppliers. They exchange vertical integration for collaboration. When done well, all parties benefit from this arrangement and the collaboration leads to the creation of an agile, lean and successful "virtual enterprise." Case in point: For Sun hardware, Oracle outsources most of its manufacturing and all of its logistics to third parties. These are vital activities, but ones where Oracle doesn't have a core competency, so we shift them to business partners who do. Within our enterprise, we always retain the core functions of product development, support, and most of the sales function, because that's what constitutes our core value to our customers. This is a perfect example of a virtual enterprise.  What are the implications of this? It means that we must exchange direct internal control for indirect external collaboration. This fundamentally changes the relative importance of different business processes, the boundaries of security and information sharing, and the relationship of the supply chain systems to the ERP. The challenge is that the systems required to support this virtual paradigm are still mired in "island enterprise" thinking. But help is at hand. Developments such as the Web, social networks, collaboration, and rules-based orchestration offer great potential to fundamentally re-architect supply chain systems to better support the virtual enterprise.  Supply Chain Management Systems in a Virtual Enterprise Historically enterprise software was constructed to automate the ERP - and then the supply chain systems extended the ERP. They were joined at the hip. In virtual enterprises, the supply chain system needs to be ERP agnostic, sitting above each of the ERPs that are distributed across the virtual enterprise - most of which are operating in other businesses. This is vital so that the supply chain system can manage the flow of material and the related information through the multiple enterprises. It has to have strong collaboration tools. It needs to be highly flexible. Users need to be able to see information that's coming from multiple sources and be able to react and respond to events across those sources.  Oracle Fusion Distributed Order Orchestration (DOO) is a perfect example of a supply chain system designed to operate in this virtual way. DOO embraces the idea that a company's fulfillment challenge is a distributed, multi-enterprise problem. It enables users to manage the process and the trading partners in a uniform way and deliver a consistent user experience while operating over a heterogeneous, virtual enterprise. This is a fundamental shift at the core of managing supply chains. It forces virtual enterprises to think architecturally about how best to construct their supply chain systems.  Case in point, almost everyone has ordered from Amazon.com at one time or another. Our orders are as likely to be fulfilled by third parties as they are by Amazon itself. To deliver the order promptly and efficiently, Amazon has to send it to the right fulfillment location and know the availability in that location. It needs to be able to track status of the fulfillment and deal with exceptions. As a virtual enterprise, Amazon's operations, using thousands of trading partners, requires a very different approach to fulfillment than the traditional 'take an order and ship it from your own warehouse' model. Amazon had no choice but to develop a complex, expensive and custom solution to tackle this problem as there used to be no product solution available. Now, other companies who want to follow similar models have a better off-the-shelf choice -- Oracle Distributed Order Orchestration (DOO).  Consider how another of our customers is using our distributed orchestration solution. This major airplane manufacturer has a highly complex business and interacts regularly with the U.S. Government and major airlines. It sits in the middle of an intricate supply chain and needed to improve visibility across its many different entities. Oracle Fusion DOO gives the company an orchestration mechanism so it could improve quality, speed, flexibility, and consistency without requiring an organ transplant of these highly complex legacy systems. Many retailers face the challenge of dealing with brick and mortar, Web, and reseller channels. They all need to be knitted together into a virtual enterprise experience that is consistent for their customers. When a large U.K. grocer with a strong brick and mortar retail operation added an online business, they turned to Oracle Fusion DOO to bring these entities together. Disturbing the Peace with Acquisitions Quite often a company's ERP system is disrupted when it acquires a new company. An acquisition can inject a new set of processes and systems -- or even introduce an entirely new business like Sun's hardware did at Oracle. This challenge has been a driver for some of our DOO customers. A large power management company is using Oracle Fusion DOO to provide the flexibility to rapidly integrate additional products and services into its central fulfillment operation. The Flip Side of Fulfillment Meanwhile, we haven't ignored similar challenges on the supply side of the equation. Specifically, how to manage complex supply in a flexible way when there are multiple trading parties involved? How to manage the supply to suppliers? How to manage critical components that need to merge in a tier two or tier three supply chain? By investing in supply orchestration solutions for the virtual enterprise, we plan to give users better visibility into their network of suppliers to help them drive down costs. We also think this technology and full orchestration process can be applied to the financial side of organizations. An example is transactions that flow through complex internal structures to minimize tax exposure. We can help companies manage those transactions effectively by thinking about the internal organization as a virtual enterprise and bringing the same solution set to this internal challenge.  The Clear Front Runner No other company is investing in solving the virtual enterprise supply chain issues like Oracle is. Oracle is in a unique position to become the gold standard in this market space. We have the infrastructure of Oracle technology. We already have an Oracle Fusion DOO application which embraces the best of what's required in this area. And we're absolutely committed to extending our Fusion solution to other use cases and delivering even more business value.

  Read the article

• We've completed the first iteration

  - by CliveT

  There are a lot of features in C# that are implemented by the compiler and not by the underlying platform. One such feature is a lambda expression. Since local variables cannot be accessed once the current method activation finishes, the compiler has to go out of its way to generate a new class which acts as a home for any variable whose lifetime needs to be extended past the activation of the procedure. Take the following example:     Random generator = new Random();     Func func = () = generator.Next(10); In this case, the compiler generates a new class called c_DisplayClass1 which is marked with the CompilerGenerated attribute. [CompilerGenerated] private sealed class c__DisplayClass1 {     // Fields     public Random generator;     // Methods     public int b__0()     {         return this.generator.Next(10);     } } Two quick comments on this: (i)    A display was the means that compilers for languages like Algol recorded the various lexical contours of the nested procedure activations on the stack. I imagine that this is what has led to the name. (ii)    It is a shame that the same attribute is used to mark all compiler generated classes as it makes it hard to figure out what they are being used for. Indeed, you could imagine optimisations that the runtime could perform if it knew that classes corresponded to certain high level concepts. We can see that the local variable generator has been turned into a field in the class, and the body of the lambda expression has been turned into a method of the new class. The code that builds the Func object simply constructs an instance of this class and initialises the fields to their initial values.     c__DisplayClass1 class2 = new c__DisplayClass1();     class2.generator = new Random();     Func func = new Func(class2.b__0); Reflector already contains code to spot this pattern of code and reproduce the form containing the lambda expression, so this is example is correctly decompiled. The use of compiler generated code is even more spectacular in the case of iterators. C# introduced the idea of a method that could automatically store its state between calls, so that it can pick up where it left off. The code can express the logical flow with yield return and yield break denoting places where the method should return a particular value and be prepared to resume.         {             yield return 1;             yield return 2;             yield return 3;         } Of course, there was already a .NET pattern for expressing the idea of returning a sequence of values with the computation proceeding lazily (in the sense that the work for the next value is executed on demand). This is expressed by the IEnumerable interface with its Current property for fetching the current value and the MoveNext method for forcing the computation of the next value. The sequence is terminated when this method returns false. The C# compiler links these two ideas together so that an IEnumerator returning method using the yield keyword causes the compiler to produce the implementation of an Iterator. Take the following piece of code.         IEnumerable GetItems()         {             yield return 1;             yield return 2;             yield return 3;         } The compiler implements this by defining a new class that implements a state machine. This has an integer state that records which yield point we should go to if we are resumed. It also has a field that records the Current value of the enumerator and a field for recording the thread. This latter value is used for optimising the creation of iterator instances. [CompilerGenerated] private sealed class d__0 : IEnumerable, IEnumerable, IEnumerator, IEnumerator, IDisposable {     // Fields     private int 1__state;     private int 2__current;     public Program 4__this;     private int l__initialThreadId; The body gets converted into the code to construct and initialize this new class. private IEnumerable GetItems() {     d__0 d__ = new d__0(-2);     d__.4__this = this;     return d__; } When the class is constructed we set the state, which was passed through as -2 and the current thread. public d__0(int 1__state) {     this.1__state = 1__state;     this.l__initialThreadId = Thread.CurrentThread.ManagedThreadId; } The state needs to be set to 0 to represent a valid enumerator and this is done in the GetEnumerator method which optimises for the usual case where the returned enumerator is only used once. IEnumerator IEnumerable.GetEnumerator() {     if ((Thread.CurrentThread.ManagedThreadId == this.l__initialThreadId)               && (this.1__state == -2))     {         this.1__state = 0;         return this;     } The state machine itself is implemented inside the MoveNext method. private bool MoveNext() {     switch (this.1__state)     {         case 0:             this.1__state = -1;             this.2__current = 1;             this.1__state = 1;             return true;         case 1:             this.1__state = -1;             this.2__current = 2;             this.1__state = 2;             return true;         case 2:             this.1__state = -1;             this.2__current = 3;             this.1__state = 3;             return true;         case 3:             this.1__state = -1;             break;     }     return false; } At each stage, the current value of the state is used to determine how far we got, and then we generate the next value which we return after recording the next state. Finally we return false from the MoveNext to signify the end of the sequence. Of course, that example was really simple. The original method body didn't have any local variables. Any local variables need to live between the calls to MoveNext and so they need to be transformed into fields in much the same way that we did in the case of the lambda expression. More complicated MoveNext methods are required to deal with resources that need to be disposed when the iterator finishes, and sometimes the compiler uses a temporary variable to hold the return value. Why all of this explanation? We've implemented the de-compilation of iterators in the current EAP version of Reflector (7). This contrasts with previous version where all you could do was look at the MoveNext method and try to figure out the control flow. There's a fair amount of things we have to do. We have to spot the use of a CompilerGenerated class which implements the Enumerator pattern. We need to go to the class and figure out the fields corresponding to the local variables. We then need to go to the MoveNext method and try to break it into the various possible states and spot the state transitions. We can then take these pieces and put them back together into an object model that uses yield return to show the transition points. After that Reflector can carry on optimising using its usual optimisations. The pattern matching is currently a little too sensitive to changes in the code generation, and we only do a limited analysis of the MoveNext method to determine use of the compiler generated fields. In some ways, it is a pity that iterators are compiled away and there is no metadata that reflects the original intent. Without it, we are always going to dependent on our knowledge of the compiler's implementation. For example, we have noticed that the Async CTP changes the way that iterators are code generated, so we'll have to do some more work to support that. However, with that warning in place, we seem to do a reasonable job of decompiling the iterators that are built into the framework. Hopefully, the EAP will give us a chance to find examples where we don't spot the pattern correctly or regenerate the wrong code, and we can improve things. Please give it a go, and report any problems.

  Read the article

• Graph visualization code in javascript?

  - by Chris Farmer

  Hi. I have a data structure that represents a directed graph, and I want to render that dynamically on an HTML page. Does anyone know of any javascript code that can do a reasonable job with graph layout? These graphs will usually be just a few nodes, maybe ten at the very upper end, so my guess is that performance isn't going to be a big deal. Ideally, I'd like to be able to hook it in with jQuery so that users can tweak the layout manually by dragging the nodes around. Edit: Google's Visualization API seems to be more "graphs as charts" oriented than "graphs as nodes" oriented. I didn't see any node-oriented visualizations already built there, anyway. Do you know that one exists?

  Read the article

• dynamic dashboard interface

  - by user208081

  I want to create an interface similar to the following in Silverlight. http://demos6.dundas.com/Silverlight/ I need to create a dashboard where different elements can be re-arranged using Silverlight. The dashboard elements can be different usercontrols that in turn may contain charts, guages, grids...... The user should be able to dynamically add and remove dashboard elements. The user should also be able to use drag and drop to reposition the dashboard elements. If there are some code samples to get me started, that will be great as we are just starting out on some Silverlight development. Thanks, Pratik

  Read the article

• Can we have ExtJs components inside a Flex driven page

  - by shafi

  Hi, I am working on a page which mainly consists of Charts and Grids. Thought that Flex would be the best fit with some cool effects. But however, I now feel that ExtJs grid looks better than Flex data grid. My question is whether there is any possibility / mechanism to embed Ext JS grid into a Flex page. Lets say my main page has a Flex tab panel. In first tab, I would like to see 'Flex Chart' and in second tab I would want to see 'ExtJS grid'. I would also want to know of any Flex Data grid plugin (if exists), which looks/works just like Ext Js grid. Thanks & Regards Shafi

  Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >