Search Results

Search found 10951 results on 439 pages for 'high definition'.

Page 59/439 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

  • lm-sensor and cpu temperatures

    - by nalsanj
    i am on ubuntu Precise Pangolin. The processor is Intel i3. a desktop. i installed lm-sensors and below is the report "sensors" gave coretemp-isa-0000 Adapter: ISA adapter Core 0: +30.0°C (high = +89.0°C, crit = +105.0°C) Core 2: +33.0°C (high = +89.0°C, crit = +105.0°C) w83627dhg-isa-0a10 Adapter: ISA adapter Vcore: +0.93 V (min = +0.00 V, max = +1.74 V) in1: +0.75 V (min = +1.99 V, max = +1.99 V) ALARM AVCC: +3.36 V (min = +2.98 V, max = +3.63 V) +3.3V: +3.36 V (min = +2.98 V, max = +3.63 V) in4: +1.30 V (min = +0.90 V, max = +1.77 V) in5: +0.76 V (min = +1.15 V, max = +0.90 V) ALARM in6: +1.06 V (min = +0.94 V, max = +2.03 V) 3VSB: +3.36 V (min = +2.98 V, max = +3.63 V) Vbat: +3.36 V (min = +2.70 V, max = +3.30 V) ALARM fan1: 0 RPM (min = 3515 RPM, div = 128) ALARM fan2: 0 RPM (min = 10546 RPM, div = 128) ALARM fan3: 0 RPM (min = 10546 RPM, div = 128) ALARM fan5: 0 RPM (min = 10546 RPM, div = 128) ALARM temp1: +39.0°C (high = -121.0°C, hyst = +9.0°C) ALARM sensor = diode temp2: +39.0°C (high = +80.0°C, hyst = +75.0°C) sensor = diode temp3: +127.0°C (high = +80.0°C, hyst = +75.0°C) ALARM sensor = thermistor cpu0_vid: +2.050 V intrusion0: OK radeon-pci-0100 Adapter: PCI adapter temp1: +70.5°C The fans sensors are detecting 0 RPM and some temperatures are out of range - the ALARMs above but i dont understand it very well. Can someone help out?

    Read the article

  • Laptop runs HOT after 12.10 upgrade!

    - by dinkelk
    I was running 12.04 for 6 months, my laptop ran almost silently and cool enough to hold on my lap. I updated to 12.10 and now my computer gets too hot to hold on my lap and the fan is constantly running on full blast. This is the output of sensors: acpitz-virtual-0 Adapter: Virtual device temp1: +84.0°C (crit = +99.0°C) coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +84.0°C (high = +86.0°C, crit = +100.0°C) Core 0: +74.0°C (high = +86.0°C, crit = +100.0°C) Core 1: +72.0°C (high = +86.0°C, crit = +100.0°C) Core 2: +75.0°C (high = +86.0°C, crit = +100.0°C) Core 3: +84.0°C (high = +86.0°C, crit = +100.0°C) radeon-pci-0100 Adapter: PCI adapter temp1: +76.0°C I have an HP Pavilion dv6, i7, amd radeon graphics. Please let me know if you need additional information. What could be different between the two Ubuntu additions that caused such a drastic change? Edit 1: Per @Paul's suggestion, I ran htop to try to narrow down the problem. Here is the result! This is about 10 minutes after boot-up, htop, yakuake, and a chrome page with 1 tab opened to this question are all that I have manually opened. The most taxing program to the CPU is htop itself. I think that the problem must lie elsewhere; my temps are already up to ~65C for the CPU and ~69C for the GPU, with nearly 0% CPU usage.

    Read the article

  • OUCH! Laptop running SUPER HOT after 12.10 upgrade!

    - by dinkelk
    I was running 12.04 for 6 months, my laptop ran almost silently and cool enough to hold on my lap. I updated to 12.10 and now my computer gets too hot to hold on my lap and the fan is constantly running on full blast. This is the output of sensors: acpitz-virtual-0 Adapter: Virtual device temp1: +84.0°C (crit = +99.0°C) coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +84.0°C (high = +86.0°C, crit = +100.0°C) Core 0: +74.0°C (high = +86.0°C, crit = +100.0°C) Core 1: +72.0°C (high = +86.0°C, crit = +100.0°C) Core 2: +75.0°C (high = +86.0°C, crit = +100.0°C) Core 3: +84.0°C (high = +86.0°C, crit = +100.0°C) radeon-pci-0100 Adapter: PCI adapter temp1: +76.0°C I have an HP Pavilion dv6, i7, amd radeon graphics. Please let me know if you need additional information. What could be different between the two Ubuntu editions that caused such a drastic change? Edit 1: Per @Paul's suggestion, I ran htop to try to narrow down the problem. Here is the result! (left side of terminal) (right side of terminal) This is about 10 minutes after boot-up, htop, yakuake, and a chrome page with 1 tab opened to this question are all that I have manually opened. The most taxing program to the CPU is htop itself. I think that the problem must lie elsewhere; my temps are already up to ~65C for the CPU and ~69C for the GPU, with nearly 0% CPU usage.

    Read the article

  • Root cause for high CPU usage; which measurement to trust more: Windows Task Manager or Process Explorer?

    - by p.campbell
    Consider this Windows 8.1 machine (in-place upgrade from Windows 8) with differing reports on its CPU usage. The machine is idle, and has been for 3 days. There are no CPU intensive tasks running currently nor over the 3 day idle period. Windows Task Manager is reporting CPU usage constantly at an incredibly high value (and increasing over time!) at around 75%. Process Explorer from SysInternals reports that the CPU usage is much different at around 42% How does Process Explorer report 42.14% usage, but its columns report Idle at 57%, with the sum of the other processes not even approaching 10%? Which of these two values should I trust more, and why should it be trusted over the other measurement? How can I actually determine which process is causing Task Manager to report its values? These Proc Exp metrics were taken with Administrator privileges, and with option 'Show Details for All Processes' Click for larger view:

    Read the article

  • New Whitepaper - Exalogic Virtualization Architecture

    - by Javier Puerta
    One of the key enhancements in the current generation of Oracle Exalogic systems—and the focus of this whitepaper—is Oracle’s incorporation of virtualized InfiniBand I/O interconnects using Single Root I/O Virtualization (SR-IOV) technology to permit the system to share the internal InfiniBand network and storage fabric between as many as 63 virtual machines per physical server node with near-native performance simultaneously allowing both high performance and high workload consolidation. Download it here: An Oracle White Paper - November 2012- Oracle Exalogic Elastic Cloud: Advanced I/O Virtualization Architecture for Consolidating High-Performance Workloads

    Read the article

  • ?Oracle Database 12c????ASM Scrubbing Disk Groups

    - by Liu Maclean(???)
    ?12.1?Oracle ASM??????????????????? ??Scrubbing Disk Groups, Disk Scrubbing???????????,?????Normal ??High Redundancy?disk group?????? Scrubbing ?????????????????Disk Scrubbing???disk group rebalancing???????I/O?????Disk Scrubbing??????I/O????? ?????????Scrubbing????,?????,????????????,?????ALTER DISKGROUP?????????: SQL> ALTER DISKGROUP data SCRUB POWER LOW; SQL> ALTER DISKGROUP data SCRUB FILE '+DATA/ORCL/ASKMACLEAN/example.266.806582193' REPAIR POWER HIGH FORCE; SQL> ALTER DISKGROUP data SCRUB DISK DATA_0005 REPAIR POWER HIGH FORCE; ?????SCRUB ?: ??REPAIR??????????,?????REPAIR,?SCRUB???????????????? ??POWER?????AUTO LOW HIGH ??MAX? ?POWER???,???AUTO????? ??WAIT ???????scrubbing ?????????WAIT???,?scrubbing??????scrubbing queue ??,??????? ?FORCE?????,?????I/O????????????????scrubbing ,????????

    Read the article

  • XSLT, process elements one by one

    - by qui
    Hi I am quite weak at XSLT so this might seem obvious. Here is some sample XML <term> <name>cholecystocolonic fistula</name> <definition>blah blah</definition> <reference>cholecystocolostomy</reference> </term> And here is the XSLT I wrote a while ago to process it <xsl:template name="term"> { "dictitle": "<xsl:value-of select="name" disable-output-escaping="yes" />", "html": "<xsl:value-of select="definition" disable-output-escaping="yes"/>", "referece": "<xsl:value-of select="reference" disable-output-escaping="yes"/> } </xsl:template> Basically I am creating JSON from the XML. The requirements have now changed so that now the XML can have more than one definition tag and reference tag. They can appear in any order, i.e definition, reference, reference, definition, reference. How can I update the XSLT to accommodate this? Probably worth mentioning that because my XSLT processor is using .NET I can only use XSLT 1.0 commands. Many thanks!

    Read the article

  • Is there command-line tool to extract typedef, structure, enumeration, variable, function from a C or C++ file?

    - by FooF
    I am desiring a command-line tool to extract a definition or declaration (typedef, structure, enumeration, variable, or function) from a C or C++ source file. Also a way to replace an existing definition/declaration would be handy (after transforming the extracted definition by a user-submitted script). Is there such generic tool available, or is some resonably close approximation of such a tool? Scriptability and ability to hook-up with user created scripts or programs is of importance here, although I am academically curious of GUI programs too. Open source solutions for Unix/Linux camp are preferred (although I am curious of Windows and OS X tools too). Primary language interests are C and C++ but more generic solution would be even better (I think we do not need super accurate parsing capabilities for finding, extracting and replacing a definition in a program source file). Sample Use Cases (extra - for the curious mind): Given deeply nested structs and variable (array) initializations of these types, suppose there is a need to change a struct definition by adding or reordering fields or rewriting the variable/array definitions in more readable format without introducing errors resulting from manual labor. This would work by extracting the old initializations, then using a script/program to write the new initializations to replace the old ones. For implementing a code browsing tool - extract a definition. Decorative code generation (e.g. logging function entries / returns). Scripted code structuring (e.g. extract this and that thing and put in different place without change - version control commit comment could document the command to perform this operation to make it evident and verifiable that nothing changed). Note about tags: More accurate tag than code-generation would be code-transformation but it does not exist.

    Read the article

  • Formatting data from management database

    - by bVector
    I've got some data that goes like this: Config_Name Question Answer Cisco WAN Sensitivity: High Cisco WAN Authorized Users: Brent, Charles Cisco WAN Last Audited: n/a Cisco WAN Next Audit: 3/30/2012 Cisco WAN Audit Signature: Cisco WAN Username: MYCOMPANY Cisco WAN Password: Cisco WAN Encrypted-A ENCRYPTED DATA Cisco WAN Encrypted-B Cisco WAN Encrypted-C vCenter server Sensitivity: High vCenter server Authorized Users: Brent, Charles vCenter server Last Audited: vCenter server Next Audit: 3/30/2012 vCenter server Audit Signature: ENCRYPTED DATA vCenter server Username: administrator vCenter server Password: vCenter server Encrypted-A ENCRYPTED DATA vCenter server Encrypted-B vCenter server Encrypted-C AKSC-NE01 IPMI Sensitivity: High AKSC-NE01 IPMI Authorized Users: Brent, Charles AKSC-NE01 IPMI Last Audited: AKSC-NE01 IPMI Next Audit: 3/30/2012 AKSC-NE01 IPMI Audit Signature: ENCRYPTED DATA AKSC-NE01 IPMI Username: MYCOMPANY AKSC-NE01 IPMI Password: AKSC-NE01 IPMI Encrypted-A ENCRYPTED DATA AKSC-NE01 IPMI Encrypted-B AKSC-NE01 IPMI Encrypted-C and I need it to be in this format: Config_Name Sensitivity: Authorized Users: Last Audited: Next Audit: Audit Signature: Username: Password: Encrypted-A Encrypted-B Encrypted-C AKSC-NE01 IPMI High Brent, Charles 3/30/2012 ENCRYPTED DATA MYCOMPANY ENCRYPTED DATA Cisco ASA5505 WAN High Brent, Charles n/a 3/30/2012 ENCRYPTED DATA MYCOMPANY ENCRYPTED DATA vCenter server High Brent, Charles 3/30/2012 ENCRYPTED DATA administrator ENCRYPTED DATA the tabs get messed up on here but hopefully you get my drift. does anyone know an easy way to do this? I haven't found one with excel just yet.

    Read the article

  • What is Best storage servers infrastructure ? DAS/NAS/SAN or installing GlusterFS/LUSTER/HDFS/RBDB

    - by TORr0t
    I am trying to design an infrastucture for the project I am working on. It would be somehow a file-sharing/downloading project (like rapidshare) and I would need high storage sizes and good scability, and I would add new storage nodes after my project grows up. I have come up with 3 solutions for my project which are using Luster, GlusterFS, HDFS, RDBD. For start, i would have 2 servers, one server is for glusterfs client + webserver + db server+ a streaming server, and the other server is gluster storage node. (After sometime, i would be adding more node servers, and client servers (dont know how many new client new servers to add, will see later) So, i am thinking to work with glusterfs. But i really wonder that if i have to use high performance servers with high sotrage sizes or avarage/slow servers with high storage sizes? Or nas/das/san solutions are better for glusterfs storage nodes? I might buy a nas and install glusterfs onto it. I would be happy to listen to your recommendations for the server properties (for each clients and nodes) . I really dont know if I really need high amount of ram and good cpus to for the nodes. I am sure i need it for client servers. The files would be streamed as well, so the Automatic file replication is important, thus, my system should work like a cloud, when needed, according to high traffic, the storage nodes should copy the most demanded file to be streamed and would help me to get rid of scability problems and my visitors would able to stream/download those files. Also, i am open to your experiences/thoughts about any good solution. Luster, hdfs, rbdb are the other options and i would be happy to listen to your thoughts here. I would be very very happy to hear back from anyone commented of any words I have used here. Thanks

    Read the article

  • Very high CPU and low RAM usage - is it possible to place some of swap some of the CPU usage to the RAM (with CloudLinux LVE Manager installed)?

    - by Chriswede
    I had to install CloudLinux so that I could somewhat controle the CPU ussage and more importantly the Concurrent-Connections the Websites use. But as you can see the Server load is way to high and thats why some sites take up to 10 sec. to load! Server load 22.46 (8 CPUs) (!) Memory Used 36.32% (2,959,188 of 8,146,632) (ok) Swap Used 0.01% (132 of 2,104,504) (ok) Server: 8 x Intel(R) Xeon(R) CPU E31230 @ 3.20GHz Memory: 8143680k/9437184k available (2621k kernel code, 234872k reserved, 1403k data, 244k init) Linux Yesterday: Total of 214,514 Page-views (Awstat) Now my question: Can I shift some of the CPU usage to the RAM? Or what else could I do to make the sites run faster (websites are dynamic - so SQL heavy) Thanks top - 06:10:14 up 29 days, 20:37, 1 user, load average: 11.16, 13.19, 12.81 Tasks: 526 total, 1 running, 524 sleeping, 0 stopped, 1 zombie Cpu(s): 42.9%us, 21.4%sy, 0.0%ni, 33.7%id, 1.9%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 8146632k total, 7427632k used, 719000k free, 131020k buffers Swap: 2104504k total, 132k used, 2104372k free, 4506644k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 318421 mysql 15 0 1315m 754m 4964 S 474.9 9.5 95300:17 mysqld 6928 root 10 -5 0 0 0 S 2.0 0.0 90:42.85 kondemand/3 476047 headus 17 0 172m 19m 10m S 1.7 0.2 0:00.05 php 476055 headus 18 0 172m 18m 9.9m S 1.7 0.2 0:00.05 php 476056 headus 15 0 172m 19m 10m S 1.7 0.2 0:00.05 php 476061 headus 18 0 172m 19m 10m S 1.7 0.2 0:00.05 php 6930 root 10 -5 0 0 0 S 1.3 0.0 161:48.12 kondemand/5 6931 root 10 -5 0 0 0 S 1.3 0.0 193:11.74 kondemand/6 476049 headus 17 0 172m 19m 10m S 1.3 0.2 0:00.04 php 476050 headus 15 0 172m 18m 9.9m S 1.3 0.2 0:00.04 php 476057 headus 17 0 172m 18m 9.9m S 1.3 0.2 0:00.04 php 6926 root 10 -5 0 0 0 S 1.0 0.0 90:13.88 kondemand/1 6932 root 10 -5 0 0 0 S 1.0 0.0 247:47.50 kondemand/7 476064 worldof 18 0 172m 19m 10m S 1.0 0.2 0:00.03 php 6927 root 10 -5 0 0 0 S 0.7 0.0 93:52.80 kondemand/2 6929 root 10 -5 0 0 0 S 0.3 0.0 161:54.38 kondemand/4 8459 root 15 0 103m 5576 1268 S 0.3 0.1 54:45.39 lvest

    Read the article

  • Nagios notifications definitions

    - by Colin
    I am trying to monitor a web server in such a way that I want to search for a particular string on a page via http. The command is defined in command.cfg as follows # 'check_http-mysite command definition' define command { command_name check_http-mysite command_line /usr/lib/nagios/plugins/check_http -H mysite.example.com -s "Some text" } # 'notify-host-by-sms' command definition define command { command_name notify-host-by-sms command_line /usr/bin/send_sms $CONTACTPAGER$ "Nagios - $NOTIFICATIONTYPE$ :Host$HOSTALIAS$ is $HOSTSTATE$ ($OUTPUT$)" } # 'notify-service-by-sms' command definition define command { command_name notify-service-by-sms command_line /usr/bin/send_sms $CONTACTPAGER$ "Nagios - $NOTIFICATIONTYPE$: $HOSTALIAS$/$SERVICEDESC$ is $SERVICESTATE$ ($OUTPUT$)" } Now if nagios doesn't find "Some text" on the home page mysite.example.com, nagios should notify a contact via sms through the Clickatell http API which I have a script for that that I have tested and found that it works fine. Whenever I change the command definition to search for a string which is not on the page, and restart nagios, I can see on the web interface that the string was not found. What I don't understand is why isn't the notification sent though I have defined the host, hostgroup, contact, contactgroup and service and so forth. What I'm I missing, these are my definitions, In my web access through the cgi I can see that I have notifications have been defined and enabled though I don't get both email and sms notifications during hard status changes. host.cfg define host { use generic-host host_name HAL alias IBM-1 address xxx.xxx.xxx.xxx check_command check_http-mysite } *hostgroups_nagios2.cfg* # my website define hostgroup{ hostgroup_name my-servers alias All My Servers members HAL } *contacts_nagios2.cfg* define contact { contact_name colin alias Colin Y service_notification_period 24x7 host_notification_period 24x7 service_notification_options w,u,c,r,f,s host_notification_options d,u,r,f,s service_notification_commands notify-service-by-email,notify-service-by-sms host_notification_commands notify-host-by-email,notify-host-by-sms email [email protected] pager +254xxxxxxxxx } define contactgroup{ contactgroup_name site_admin alias Site Administrator members colin } *services_nagios2.cfg* # check for particular string in page via http define service { hostgroup_name my-servers service_description STRING CHECK check_command check_http-mysite use generic-service notification_interval 0 ; set > 0 if you want to be renotified contacts colin contact_groups site_admin } Could someone please tell me where I'm going wrong. Here are the generic-host and generic-service definitions *generic-service_nagios2.cfg* # generic service template definition define service{ name generic-service ; The 'name' of this service template active_checks_enabled 1 ; Active service checks are enabled passive_checks_enabled 1 ; Passive service checks are enabled/accepted parallelize_check 1 ; Active service checks should be parallelized (disabling this can lead to major performance problems) obsess_over_service 1 ; We should obsess over this service (if necessary) check_freshness 0 ; Default is to NOT check service 'freshness' notifications_enabled 1 ; Service notifications are enabled event_handler_enabled 1 ; Service event handler is enabled flap_detection_enabled 1 ; Flap detection is enabled failure_prediction_enabled 1 ; Failure prediction is enabled process_perf_data 1 ; Process performance data retain_status_information 1 ; Retain status information across program restarts retain_nonstatus_information 1 ; Retain non-status information across program restarts notification_interval 0 ; Only send notifications on status change by default. is_volatile 0 check_period 24x7 normal_check_interval 5 retry_check_interval 1 max_check_attempts 4 notification_period 24x7 notification_options w,u,c,r contact_groups site_admin register 0 ; DONT REGISTER THIS DEFINITION - ITS NOT A REAL SERVICE, JUST A TEMPLATE! } *generic-host_nagios2.cfg* define host{ name generic-host ; The name of this host template notifications_enabled 1 ; Host notifications are enabled event_handler_enabled 1 ; Host event handler is enabled flap_detection_enabled 1 ; Flap detection is enabled failure_prediction_enabled 1 ; Failure prediction is enabled process_perf_data 1 ; Process performance data retain_status_information 1 ; Retain status information across program restarts retain_nonstatus_information 1 ; Retain non-status information across program restarts max_check_attempts 10 notification_interval 0 notification_period 24x7 notification_options d,u,r contact_groups site_admin register 1 ; DONT REGISTER THIS DEFINITION - ITS NOT A REAL HOST, JUST A TEMPLATE! }

    Read the article

  • compile lastest bnx2 driver on debian squeeze

    - by markus
    I want to upgrade the bnx2 network card driver in a Dell Power Edge R410. I downloaded the latest driver version from the broadcom website. If I want to compile the driver it fails with the following errors: make make -C bnx2/src KVER=2.6.32-5-amd64 PREFIX= make[1]: Entering directory `/tmp/netxtreme2-6.2.23/bnx2-2.0.23b/src' make -C /lib/modules/2.6.32-5-amd64/build SUBDIRS=/tmp/netxtreme2-6.2.23/bnx2-2.0.23b/src modules make[2]: Entering directory `/usr/src/linux-headers-2.6.32-5-amd64' Building modules, stage 2. MODPOST 2 modules make[2]: Leaving directory `/usr/src/linux-headers-2.6.32-5-amd64' make[1]: Leaving directory `/tmp/netxtreme2-6.2.23/bnx2-2.0.23b/src' make -C bnx2x/src KVER=2.6.32-5-amd64 PREFIX= make[1]: Entering directory `/tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src' make -C /lib/modules/2.6.32-5-amd64/build M=`pwd` modules make[2]: Entering directory `/usr/src/linux-headers-2.6.32-5-amd64' CC [M] /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.o In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1009:1: error: "PCI_VPD_LRDT_ID_STRING" redefined In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:34: /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1327:1: error: this is the location of the previous definition In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1011:1: error: "PCI_VPD_LRDT_RO_DATA" redefined In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:34: /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1328:1: error: this is the location of the previous definition In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1013:1: error: "PCI_VPD_LRDT_RW_DATA" redefined In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:34: /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1329:1: error: this is the location of the previous definition In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1019:1: error: "PCI_VPD_SRDT_END" redefined In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:34: /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1334:1: error: this is the location of the previous definition In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1032: error: conflicting types for ‘pci_vpd_lrdt_size’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1355: error: previous definition of ‘pci_vpd_lrdt_size’ was here /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1037: error: conflicting types for ‘pci_vpd_srdt_size’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1366: error: previous definition of ‘pci_vpd_srdt_size’ was here /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1042: error: conflicting types for ‘pci_vpd_find_tag’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1391: error: previous declaration of ‘pci_vpd_find_tag’ was here /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1077: error: conflicting types for ‘pci_vpd_info_field_size’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1377: error: previous definition of ‘pci_vpd_info_field_size’ was here /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1082: error: conflicting types for ‘pci_vpd_find_info_keyword’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1403: error: previous declaration of ‘pci_vpd_find_info_keyword’ was here make[5]: *** [/tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.o] Fehler 1 make[4]: *** [_module_/tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src] Fehler 2 make[3]: *** [sub-make] Fehler 2 make[2]: *** [all] Fehler 2 make[2]: Leaving directory `/usr/src/linux-headers-2.6.32-5-amd64' make[1]: *** [bnx2x.o] Fehler 2 make[1]: Leaving directory `/tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src' make: *** [l2build] Fehler 2

    Read the article

  • adding a div with data()

    - by Dizzy Bryan High
    Hi people am generating a list of flash swfs, the information comes from an ajax call which returns a json object which i loop through to create the rows of data using my makeAppRow function. makeAppRow = function(myData){ var myStr = '<div class="fileEntry">' myStr = myStr +'<div class="appDate">'+dateFormat(myData.date_swf, "dS mmmm, yyyy, h:MM TT")+'</div>' myStr = myStr +'<div class="appName">'+myData.name_swf+'</div>' myStr = myStr +'<div class="appOptions" data>' myStr = myStr +'<div class="gotoAppBtn" data-options="'+myData+'">Open App</div>' myStr = myStr +'</div>' myStr = myStr +'</div>' $('#appData').append(myStr); } I need the json data to be attached to the gotoAppBtn so that when its clicked i can read in the data from the attached json object and use it in my click function, as you can see ive been trying to embed the data using the html5 data but i cant get it to work. <div class="gotoAppBtn" data-options="'+myData+'">Open App</div> i have a function so that when the button is clicked it loads in an swf. $('.gotoAppBtn').live('click', function(){ //alert('button clicked') var myData = $(this).data("options") alert('../userfiles/'+myData.id_ugp+'/'+myData.id_swf+'/'+myData.launchfile_swf+'') console.log(myData); var flashvars = {}; var params = {}; params.menu = "false"; params.quality = "best"; params.scale = "noscale"; var attributes = {}; attributes.id = "flashAppDisplay"; attributes.name = "flashAppDisplay"; swfobject.embedSWF( '../userfiles/'+myData.id_ugp+'/'+myData.id_swf+'/'+myData.launchfile_swf+'', 'flashAppDisplay', myData.width_swf, myData.height_swf, myData.version_swf ,"../FAVideo/expressInstall.swf", flashvars, params, attributes) }); but the data does not seem to be there, any pointers on where i am going wrong, or a better way to achive this???

    Read the article

  • OpenGL 2 on Android: native window

    - by ThreaderSlash
    According to OGLES specification, we have the following definition: EGLSurface eglCreateWindowSurface(EGLDisplay display, EGLConfig config, NativeWindowType native_window, EGLint const * attrib_list) More details, here: http://www.khronos.org/opengles/documentation/opengles1_0/html/eglCreateWindowSurface.html And also by definition: int32_t ANativeWindow_setBuffersGeometry(ANativeWindow* window, int32_t width, int32_t height, int32_t format); More details, here: http://mobilepearls.com/labs/native-android-api I am running Android Native App on OGLES 2 and debugging it in a Samsung Nexus device. For setting up the 3D scene graph environment, the following variables are defined: struct android_app { ... ANativeWindow* window; }; android_app* mApplication; ... mApplication=&pApplication; And to initialize the App, we run the commands in the code: ANativeWindow_setBuffersGeometry(mApplication->window, 0, 0, lFormat); mSurface = eglCreateWindowSurface(mDisplay, lConfig, mApplication->window, NULL); Funny to say is that, the command ANativeWindow_setBuffersGeometry behaves as expected and works fine according to its definition, accepting all the parameters sent to it. But the eglCreateWindowSurface does no accept the parameter mApplication-window, as it should accept according to its definition. Instead, it looks for the following input: EGLNativeWindowType hWnd; mSurface = eglCreateWindowSurface(mDisplay,lConfig,hWnd,NULL); As an alternative, I considered to use instead: NativeWindowType hWnd=android_createDisplaySurface(); But debugger says: Function 'android_createDisplaySurface' could not be resolved Can someone tell if there is a way to convert mApplication-window? In a way that the data from the android_app get accepted to the window surface?

    Read the article

  • BizTalk - Removing BAM Activities and Views using bm.exe

    - by Stuart Brierley
    Originally posted on: http://geekswithblogs.net/StuartBrierley/archive/2013/10/16/biztalk---removing-bam-activities-and-views-using-bm.exe.aspxOn the project I am currently working on, we are making quite extensive use of BAM within our growing number of BizTalk applications, all of which are being deployed and undeployed using the excellent Deployment Framework for BizTalk 5.0.Recently I had an issue where problems on the build server had left the target development servers in a state where the BAM activities and views for a particular application were not being removed by the undeploy process and unfortunately the definition in the solution had changed meaning that I could not easily recreate the file from source control.  To get around this I used the bm.exe application from the command line to manually remove the problem BAM artifacts - bm.exe can be found at the following path:C:\Program Files (x86)\Microsoft BizTalk Server 2010\TrackingC:\Program Files (x86)\Microsoft BizTalk Server 2010\TrackingStep1 :Get the BAM Definition FileRun the following command to get the BAm definition file, containing the details of all the activities, views and alerts:bm.exe get-defxml -FileName:{Path and File Name Here}.xmlStep 2: Remove the BAM ArtifactsAt this stage I chose to manually remove each of my problem BAM activities and views using seperate command line calls.  By looking in the definition file I could see the names of the activities and views that I wanted to remove and then use the following commands to remove first the views and then the activities:bm.exe remove-view -name:{viewname}bm.exe remove-activity -name:{activityname}

    Read the article

  • Upstart: best way for shutdown hook?

    - by Binarus
    Hi, since Ubuntu relies on upstart for some time now, I would like to use an upstart job to gracefully shutdown certain applications on system shutdown or reboot. It is essential that the system's shutdown or reboot is stalled until these applications are shut down. The applications will be started manually on occasion, and on system shutdown should automatically be ended by a script (which I already have). Since the applications can't be ended reliably without (nearly all) other services running, ending the applications has to be done before the rest of the shutdown begins. I think I can solve this by an upstart job which will be triggered on shutdown, but I am unsure which events I should use in which manner. So far, I have read the following (partly contradicting) statements: There is no general shutdown event in upstart Use a stanza like "start on starting shutdown" in the job definition Use a stanza like "start on runlevel [06S]" in the job definition Use a stanza like "start on starting runlevel [06S]" in the job definition Use a stanza like "start on stopping runlevel [!06S]" in the job definition From these recommendations, the following questions arise: Is there or is there not a general shutdown event in Ubuntu's upstart? What is the recommended way to implement a "shutdown hook"? When are the events runlevel [x] triggered; is this when having entered the runlevel or when entering the runlevel? Can we use something like "start on starting runlevel [x]" or "start on stopping runlevel [x]"? What would be the best solution for my problem? Thank you very much, Binarus

    Read the article

  • Best way to make a shutdown hook?

    - by Binarus
    Since Ubuntu relies on upstart for some time now, I would like to use an upstart job to gracefully shutdown certain applications on system shutdown or reboot. It is essential that the system's shutdown or reboot is stalled until these applications are shut down. The applications will be started manually on occasion, and on system shutdown should automatically be ended by a script (which I already have). Since the applications can't be ended reliably without (nearly all) other services running, ending the applications has to be done before the rest of the shutdown begins. I think I can solve this by an upstart job which will be triggered on shutdown, but I am unsure which events I should use in which manner. So far, I have read the following (partly contradicting) statements: There is no general shutdown event in upstart Use a stanza like "start on starting shutdown" in the job definition Use a stanza like "start on runlevel [06S]" in the job definition Use a stanza like "start on starting runlevel [06S]" in the job definition Use a stanza like "start on stopping runlevel [!06S]" in the job definition From these recommendations, the following questions arise: Is there or is there not a general shutdown event in Ubuntu's upstart? What is the recommended way to implement a "shutdown hook"? When are the events runlevel [x] triggered; is this when having entered the runlevel or when entering the runlevel? Can we use something like "start on starting runlevel [x]" or "start on stopping runlevel [x]"? What would be the best solution for my problem? Thank you very much

    Read the article

  • OpenGL ES 2 on Android: native window

    - by ThreaderSlash
    According to OGLES specification, we have the following definition: EGLSurface eglCreateWindowSurface(EGLDisplay display, EGLConfig config, NativeWindowType native_window, EGLint const * attrib_list) More details, here: http://www.khronos.org/opengles/documentation/opengles1_0/html/eglCreateWindowSurface.html And also by definition: int32_t ANativeWindow_setBuffersGeometry(ANativeWindow* window, int32_t width, int32_t height, int32_t format); More details, here: http://mobilepearls.com/labs/native-android-api I am running Android Native App on OGLES 2 and debugging it in a Samsung Nexus device. For setting up the 3D scene graph environment, the following variables are defined: struct android_app { ... ANativeWindow* window; }; android_app* mApplication; ... mApplication=&pApplication; And to initialize the App, we run the commands in the code: ANativeWindow_setBuffersGeometry(mApplication->window, 0, 0, lFormat); mSurface = eglCreateWindowSurface(mDisplay, lConfig, mApplication->window, NULL); Funny to say is that, the command ANativeWindow_setBuffersGeometry behaves as expected and works fine according to its definition, accepting all the parameters sent to it. But the eglCreateWindowSurface does no accept the parameter mApplication-window, as it should accept according to its definition. Instead, it looks for the following input: EGLNativeWindowType hWnd; mSurface = eglCreateWindowSurface(mDisplay,lConfig,hWnd,NULL); As an alternative, I considered to use instead: NativeWindowType hWnd=android_createDisplaySurface(); But debugger says: Function 'android_createDisplaySurface' could not be resolved Is 'android_createDisplaySurface' compatible only for OGLES 1 and not for OGLES 2? Can someone tell if there is a way to convert mApplication-window? In a way that the data from the android_app get accepted to the window surface?

    Read the article

  • "bug" in C++11 text by Stroustrup?

    - by Astara
    I found an apparent contradiction in the c++ text having to do with the result of the c_str() function operating on std:strings (in my copy, the definition and contradiction are on p1040). First it defines the c_str() function as something that produces a 'C-style' (zero-terminated) string, but later it talks about how a C++ c_str value can have embed a 'C'-style, end-of-string terminators (i.e. NUL's) embedded in the string (that is defined by being NUL terminated). Um... does anyone else feel that this is a 'stretching' of the definition of a C-string beyond it's definition? I.e. I think what it means, is that if you were to look at the length() function as applied to the string, it will show a different end of string than using the C-definition of a z-string -- one that can contain any character except NUL, and is terminated by NUL. I likely don't have to worry about it in my of my programs, but it seems like a subtle distinction that makes a C++ c_str, not really a 'C'-string. Am I misunderstanding this issue? Thanks!

    Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >