Search Results

Search found 18706 results on 749 pages for 'network discovery'.

Page 59/749 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

• Network config for KVM on physical machine with single NIC and single public IP

  - by neo0

  I have a physical machine running CentOS 6.4 and I will rent a place to run it in a data center. I want to install KVM on that machine to run some virtual machines. The problem is my physical machine have only one NIC and the data center give me a public IP for that interface. So how should I configure network on the physical machine to make it assign for each vm a private IP that can connect to Internet. If I create a br0 bridged with eth0 interface and create a vm with option --bridge=br0 then KVM could not assign an IP for the vm so setup can not be done. Should I use NAT mode? Does KVM have any host-only network like Virtualbox? But the vm still has to connect to outside? Thank you! Update I install the guest network using NAT (--network network:default) and then I only have to port-forwarding from the host. But if I config br0 bridged with physical eth0 then the guest can not get an IP from boot. So I removed the br0 and it worked.

  Read the article

• Networking DOS within Windows 7 XP Mode, with a Windows XP/7 Networked Share

  - by theonlylos

  For awhile now, one of my clients has been stuck with Corel Paradox 4.0 (it used to be the biggest database system in the DOS days, until Microsoft released Access in the early 90's) so for awhile I've managed to keep it on life support on Windows XP for a few years, however since switching to Windows 7 x64, I've had to resort to using XP Mode as the sandbox to keep it up and running. While I am able to run Paradox as usual in XP Mode, I'm having a serious issue where if I try connecting the install to the network share (which is located on the Windows 7 portion of the system), Paradox keeps exiting because it says the serial number is invalid. Now, I know for a fact that this is an issue with the virtual loopback adapter and also having the VM linked to the physical ethernet adapter -- and while I have solved this issue before, most of my fixes have been bandages since after a few weeks the issue pops up again. Long story short, I wanted to ask if there is a permanent way to link a DOS program to a network share address. For example, when I try doing \tsclient\paradox (the Windows 7 Address) I keep getting an error saying I need a valid network address. I've tried mapping that folder to various drive letters such as P:\Paradox -- but for some reason that keeps failing over time. For what it's worth, Paradox uses a .SOM file to store the network settings, however it isn't editable in Notepad but rather it's controlled by a wizard in Paradox. But if that extension rings any bells, I'd welcome any insights.

  Read the article

• Network login brings in user environment to any machine

  - by Jon Wilson

  In this article about Sun, the author talks about how using a Sun network meant that you could log onto any computer on a network and all of your personal tools and settings would be there. Is it possible to set up something like that with a Windows network? How about Linux?

  Read the article

• How to connect to a Virtualbox guest from the host when network cable unplugged

  - by Greg K

  I'd like to work offline (I'm flying to the US twice this month), to do this I need access to a linux development server. When I work from home I boot a VirtualBox VM and that acts as my dev server for the day (providing Apache, PHP & MySQL to run my server side code). However, I'd like to work with my VM when I'm not connected to a network. I have my Ubuntu VM guest set up with a bridge connection so it can serve HTTP and provide SSH access from inside my local network. I've tried to manually configure my network settings on both Mac OSX (the host) and Ubuntu (the guest) but I can't even ping my own NIC address (127.0.0.1 can, 192.168.21.x I can't) in OS X when I unplug the cable. Manual network settings: $ ifconfig en0 en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:xx:xx:xx:xx:xx inet 192.168.21.5 netmask 0xffffff00 broadcast 192.168.21.255 media: autoselect (100baseTX <full-duplex,flow-control>) status: active I can ping localhost fine, as well as my VM (.20) and SSH too. $ ping 192.168.21.5 PING 192.168.21.5 (192.168.21.5): 56 data bytes 64 bytes from 192.168.21.5: icmp_seq=0 ttl=64 time=0.085 ms 64 bytes from 192.168.21.5: icmp_seq=1 ttl=64 time=0.102 ms 64 bytes from 192.168.21.5: icmp_seq=2 ttl=64 time=0.100 ms 64 bytes from 192.168.21.5: icmp_seq=3 ttl=64 time=0.094 ms $ ping 192.168.21.20 PING 192.168.21.20 (192.168.21.20): 56 data bytes 64 bytes from 192.168.21.20: icmp_seq=0 ttl=64 time=0.910 ms 64 bytes from 192.168.21.20: icmp_seq=1 ttl=64 time=1.181 ms 64 bytes from 192.168.21.20: icmp_seq=2 ttl=64 time=1.159 ms 64 bytes from 192.168.21.20: icmp_seq=3 ttl=64 time=1.320 ms Network cable unplugged: $ ifconfig en0 en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:xx:xx:xx:xx:xx media: autoselect status: inactive $ ping 192.168.21.5 PING 192.168.21.5 (192.168.21.5): 56 data bytes ping: sendto: No route to host ping: sendto: No route to host Request timeout for icmp_seq 0 ping: sendto: No route to host Request timeout for icmp_seq 1 Does OS X disable the NIC when the network cable is unplugged? Any way to stop it doing this?

  Read the article

• How can I monitor network traffic in an all Mac home network?

  - by raiglstorfer

  I have an all Mac network consisting of an Airport Extreme, 1 MacPro, 1 Mac Mini, 2 MackBook Pros, 2 iPads, and 2 iPhones. The Mac Pro is connected directly to the Airport Extreme via Cat5 and the rest is all running via Wireless. Lately I've been getting prompted by Google to enter Capchas frequently. The message states that I might have software running on my network I'm not aware of. My wireless router is password protected using WPA2 Personal and I frequently change my password so I don't think someone is using the network from outside (but I've no way to confirm this). I'm looking for a relatively cheap (preferably open source) solution that would enable me to monitor and profile the network usage by machine and port. Can someone recommend a solution?

  Read the article

• Applications don't see mapped network drive after waking from sleep

  - by Chris

  I have a network share mapped as a drive letter on a Windows 7 PC that's part of a simple home network. When I wake the PC from sleep, Explorer sometimes says the drive is disconnected. Doubleclicking the drive connects it instantly, as far as Explorer is concerned. But some other applications don't see the drive unless I take additional steps (e.g., navigate to the drive in an "Open..." dialog). Is there any way to get the drive to be connected for all purposes immediately when resuming from standby? I've found the "Always wait for the network at computer startup and logon" item in Group Policy, but I'm not sure what the setting does or whether it would fix this problem. I have network discovery enabled and un-firewalled.

  Read the article

• Hardware, network infrastructure for runnng gaming server nd on VirtualGL

  - by archer

  Foud nice project VirtualGL (http://www.virtualgl.org/). Tried to run 3D fames (EVE Online, Prototype) on server and display the output on thin client using 100Mbps network. Server: Gentoo Linux on AMD Phoenom II x6 3.4Gz, 8GB RAM, 2x NVIDIA 9800 GTX in single session with display resulution 1024x768 on client. Performance is very promising. Going to increase network speed to 1Gbps (using either Ethernet or Fiber) and run 5-6 clients simultenously. My questions are: a) what would be better for network - 1Gbps Ethernet or Fiber (clients are distributed in max 20m around server)? Is that a must to use managed switch for better network performance? b) Should I increase number of video cards to put in SLI on server (going to use Gigabyte GA-890FXA-UD7 which has 6 PCIExpress slots [2 x4, 2 x8 and 2 x16]). Will it impact performance significantly. If I need to increase the number of video cards - what would be better - put 2 banks of video cards with 3 in bank using SLI, or 3 banks with 2 in the bank? Would linux recognize that and properly use all banks of video cards? c) any suggestions on good thin clients supporting 1920x1080 HDMI video and 1Gbps network I understand that my questions can't be answered clearly (unless someone already managed to use this kind of stuff ;)) although any suggestions would be very helpful.

  Read the article

• Vista Enterprise doesn't find logon servers in a network with 802.1x authentication

  - by jneves

  In a network with 802.1x configuration and a samba server configured in the domain, I have a radius server that delegates the authentication against the samba domain for users (using LDAP). The radius defines which VLAN the user is supposed to have access. I'm trying to put a Windows Vista Enterprise in the same network, but it attempts to logon the domain before authenticating against the network in 802.1x and it doesn't find any logon servers. In the radius logs I see the machine trying to authenticate with 'host/'. Does Vista enterprise require that I put it in a network with access to the logon server at that point? Thanks in advance, João Miguel Neves

  Read the article

• Slow network file transfer (under 20KB/s) on newly built x64 Win7

  - by Mangoshake

  I am getting <20KB/s for local network file transfer. If I transfer a very small file (less than 100KB) it would start quickly then slow down to <20KB/s. all subsequently network file transfer would be slow, a reboot is needed to reset this. If I transfer a large file it would be stuck on calculating for a long time and then begin with <20KB/s immediately. This is a newly built desktop running Windows 7 x64 SP1. Realtek gigabit LAN from the motherboard (ASRock Extreme3 gen3). Problematic speed is observed on the private LAN, both through ethernet and WiFi. The Router is D-Link DIR-655. Remote Differential Compression is off. Drivers are up-to-date from ASRock's website. I have tested network file transfer to and from another Windows 7 laptop and a MacBook Pro, so I am fairly certain it is the desktop's problem. The slow speed only happens with one direction also, outbound from the desktop, regardless of whether I initiate the file transfer action from the origin or the destination. Inbound network file transfer and internet speeds are fine, so I don't think this is a hardware issue. I am getting 74.8MB/s internet upload speed from speedtest.net (http://www.speedtest.net/result/1852752479.png). Inbound network file transfer I can get around 10-15MB/s. I am hoping this community has some insight for me to troubleshoot this. I don't see anything obviously related from the Event Viewer, and beyond that I just don't know where else to look. Any suggestions are greatly appreciated, thank you in advance.

  Read the article

• Wireless Network Disappearing From Available Networks (Windows 7)

  - by PeteDaMeat

  I have been using Windows 7 with a BT Voyager wireless adapter to connect to my home wireless network for around the last 6 months or so and until recently have experienced no problems. However, over the last couple of days Windows has been unable to connect to the network and the network name is no longer visible in the list of available wireless networks. The only way I have got round the problem is to reboot the NetGear router and to change the SSID to a network name which has not already been used. I do not believe the problem is with the router as my mobile phone can connect to it without any problems. The BT Voyager wireless adapter detects all other available networks so I presume this is a Windows 7 issue as it seems to occur when the PC is rebooted. This problen has happened twice in the last 2 days and is becoming extremely annoying. Does anyone have any suggestions?

  Read the article

• Network driver for Hyper-V restore from Windows Home Server

  - by Philipp Schmid

  I have backed up Windows Server 2008 running virtualized on Hyper-V to a Windows Home Server 2008 SP1 (I know I should have backed up the VHD instead). Now I need to restore the contents of the VM from WHS. I have created a restore CD ISO and used it to create a new VM. It all works as advertised up to the point where the restore process wants to load the network drivers (it only finds 4 disk drivers on the restore CD. but no network drivers). So I created a virtual floppy and copied the contents of 'Home Server Drivers for Restore onto it. But no luck! I have tried moving the 4 subdirectories into the root of the floppy, but that didn't work either. Finally, I started another instance of the WS 2008 to identify the network driver that the virtualized instance is using (%WINDOWS%\system32\drivers\netvsc60.sys) and copied that file onto the virtual floppy, without success. Does anyone have any suggestions on how to get networking working on a Hyper-V instance running off the Windows Home Server Restore CD? UPDATE: As suggested by delenda, I have added a legacy network adapter to my VM, and indeed I now get a network driver listed! However, the WHS it still not found, even after entering the home server name manually. PHS

  Read the article

• Home workers requiring simultaneous office VPN and local network access

  - by jon.simpson.uk

  I now have a large number of remote users that are using a Check Point Secure Client VPN connection into the office. These users also need access to network resources attached to their local router/hub (network storage and network printer). Is there any way that the client (Windows 7 or XP) can be configured to bypass the VPN for local addresses (192.*)

  Read the article

• Shrew VPN Client gives default route- changing the policy stops me from accessing VPN network

  - by Lock

  I am using the shrew client to connect to what I believe is a Netscreen VPN. Now, when connected, the client adds the VPN as the default route. I do not want this- there is only 1 network behind the VPN that I need to access. I found that with the shrew client, you can change the "Policy" settings on the connection, and can add your own networks in that should tunnel over the VPN. I do this, and add my network in, but when I connect the VPN, I get nothing. Can't access the network. Any idea why this would be? I can see my network in the routing table, and its correctly pointing to the correct gateway. A traceroute shows all time-outs, so I can't be 100% sure that it is trying to tunnel over the VPN. Any idea how I can troubleshoot this?

  Read the article

• How to stop Windows 7 from automatically connecting to unsecure wifi network

  - by Remi Despres-Smyth

  One of my neighbors has an unsecure wifi network called WLAN. At one point in the past, I accidentally connected to it, and disconnected immediately when I noticed. Now, when I open my laptop at home, it sometimes connects to the WLAN network first, before trying my (secured) home wifi network. The information I've found regarding this issue seems to suggest this network should have a profile on the "Manage wireless networks" screen - but it does not. How do I tell Windows 7 to never connect to networks with SSIDs called WLAN? Or to never connect to unsecured networks without confirming with me first?

  Read the article

• How to choose which network connection provides the default gateway in Windows XP

  - by Cathy

  I have a laptop with an integrated NIC and a WiFi connection. Both the wired and wireless networks I am using can access the Internet. Win XP is routing all traffic through the wireless network. I want to force it to route everything through the wired network when it is available (i.e. when I am sitting at my desk with the laptop docked) and through the wireless when that is the only option (i.e. when I have undocked my laptop and carried it to a conference room, or if I am out of the office working on a different WiFi network). The wireless connection cannot be established until after I am logged into Windows, so it's always the second network to become available to the OS. I have manually overridden the metric values in the TCP/IP configurations so that the NIC has metric 10 and the WiFi has metric 20. However, Windows is still picking the WiFi adapter's address as the Default Gateway, so this isn't helping. If I manually disable and re-enable the WiFi adapter, then it will switch the default gateway to the wired network and stay that way until I shutdown Windows. How can I tell Windows XP not to replace the default gateway when the WiFi connection is first enabled?

  Read the article

• XenServer VM's lose network settings

  - by Ash

  We deploy virtual machines using Citrix XenServer 6.0 for our clients. Two seperate clients experience the same issue: when a Server 2008 virtual machine is restarted, the static IP addresses (network address, subnet, gateway, primary DNS) don't appear to apply correctly as the IP's cannot be pinged, network services cannot be accessed etc. The issue is resolved by manually switching the network adapters to DHCP, then re-setting them to the original static IP's. While not a major issue, it's a pain when restarting servers due to Windows Updates, plus iSCSI drives need to be manually connected to Windows again via iSCSI Initiator. We have tried removed the network adapters from the virtual machine under XenCentre but without luck. Anyone experienced similar issues?

  Read the article

• How to share computer's internet connection among network users

  - by RBA

  I wanted to connect to internet from my mobile through laptop wireless-broadband internet connection.. For that I have gone to Network Places, there i have done appropriate settings for "Wireless Network Connection" and "Bluetooth Personal Area Network Connection",, but that Bluetooth connection is still not showing connected.. I have checked the option for "Allow other network users to connect through this computers Internet connection", but still my Bluetooth Connection is still showing not connected.. Please help me out,, as to how can i achieve the same,, as i am having Broadband internet connection, which comes wirelessly to my laptop through a router/modem..

  Read the article

• Teamed network cards on a Proliant Server

  - by Matt

  We have 4 network cards in a Proliant server with Server 2008R2 running Exchange 2010, with 1 card set to a static IP address and the other 3 set to DHCP. I just need some clarification as I have not teamed network cards. Do all the network cards need to have a static IP when I set as a team. The connection that has the static IP is the IP that I need to use for the Server. Is it possible to set the teamed cards to the same static IP or do I have to change the static IP to another IP then use it for the teamed IP? I will be using HP Network Configuration Utility to set this up.

  Read the article

• open source solution to a gateway for a network of a housing cooperative of 150 people

  - by SirDinosaur

  i just inherited a barely functioning network for a student housing cooperative of about 150 people. in it's current state, as i understand it from the previous person in charge of the network, we have working wireless access points and working ethernet cords going to working gigabit switches going to a barely functioning gateway (right now a simple home router) to one of three possible outbound connections. it is possible to connect to the network through the wireless or ethernet, but especially during peak hours, packets / connections are likely dropped or otherwise get no response. my intuition tells me to replace the gateway with something that can handle multiple outbound connections (WAN) and one inbound connection (LAN), while the rest of the network seems suitable for now. i'm somewhat knowledgable in Linux (been using Debian after first Arch Linux) and i want to use as much open source as possible, but i'm confused whether or not a simple server that i could easily understand will work for this situation. do i need specialized hardware to handle the switching more effectively? if so, what are my options? (i found this, thoughts?) or if a Debian server would work, anything else i should about the specs required for this type of server? also links to any useful information on using open source to maintain this type of network would be most appreciated. <3 P.S. crossposted http://redd.it/yybp2.

  Read the article

• Encrypt LAN and wifi traffic on small private network

  - by Grimlockz

  I need some advice about encrypt all traffic on a small private network running wi-fi and LAN traffic on 192.168.0.x network. The network would comprise of client laptops connecting to the wi-fi router (192.168.0.254) via ethernet connection or wireless. The main purpose of the server is for the client laptops to talk to two servers on different IP's (192.168.0.200 and 192.168.0.201) on ports 80 and 433. My main concern is having packet sniffers and what not getting access to the data. The only ways I see at the moment is to have VPN running on the network or use IPSec policy's to do this. Any other ways guys?

  Read the article

• windows 8 network cant connect to other computers

  - by Sickest

  we just setup a windows 7 ultimate file server, and all the other computers on the network, found the server expect the windows 8 computer. computers on the network: vista, win 7 ultimate, mac os, win 8 (problem) I setup a homegroup on the win 7 server pc, but the windows 8 computer can't find the homegroup, nor can it connect to the server by typing its network ext //server-pc i've tried to turn on all the windows 8 sharing to discovery ON, on Private and Public and all Networks, and got nothing. should be noted that the computer is using norton firewall/AV, im not sure if that's a factor

  Read the article

• Connecting 2 different subnet masks

  - by Jonathan

  I'm no network genius, but I have managed to get most things running. I get confused about subnets and gateways though. We have an office server connected to around 20 PC's that all communicate fine. We have just gotten a cutting machine that won't connect to our network. The server has DHCP, but that fails on the cutting machine, so I've been trying to set the IP manually. Server details are as follows: IP: 10.1.1.12 SUBNET: 255.255.255.0 GATEWAY: 10.1.1.1 Internet connection is via the modem which is 10.1.1.1 An office PC is ussually set up through DHCP and has the following settings: IP: 10.1.1.36 SUBNET: 255.255.255.0 GATEWAY: 10.1.1.1 PRIMARY DNS: 10.1.1.12 Cutting Machine computer has 2 network ports. 1 is specifically for the communication between the PC and the cutting machine. It's details must be as follows: IP: 10.100.100.2 SUBNET: 255.255.255.252 GATEWAY: BLANK The other network port need to connect to the server. I was told that the IP and SUBNET need to be as follows: IP: 10.100.100.1 SUBNET: 255.255.255.252 GATEWAY: ?? How can I connect this port to the server and/or the internet. If anyone can offer assistance, it would really be appreaciated.

  Read the article

• How to connect a Bluetooth network connection using the command line

  - by Ed Guiness

  I can enable a Local Area Network interface for my machine with the command netsh interface set interface "Local Area Connection" ENABLED Is there an equivalent command to connect a bluetooth network connection? I've tried netsh interface set interface "Bluetooth" ENABLED but it seems to have no effect, the connection remains disconnected. I also tried netsh interface set interface "Bluetooth" connect=CONNECTED but this returns One or more essential parameters not specified I know this Bluetooth connection is otherwise ok since I am able to connect using Control Panel Network Connections, right-clicking on Bluetooth Connect.

  Read the article

• How to troubleshoot intermittent and irregular connection errors on home network (preferrably Mac client)

  - by Martin

  Hi, I'm experiencing intermittent connection errors in our home network from two different computers, normally "Connection Reset" when browsing, but also other issues such as very slow throughput. I have approximately a network setup as below: ISP-Cable Modem-Dlink DIR 655 Router-(Ethernet)-Fon Router-Mac/Windows laptop Basically, is there a simple way to monitor the network and detect where issues are coming from? Right now we don't know if it is the Fon router, the Dlink router, the modem or the ISP. As the issue is intermittent, is there a software that regularly traceroutes a set of destinations and tests e.g. throughput, something that can help us figure out where in the chain the errors are introduced? The more automatic network monitor, the better.

  Read the article

• WiFi: Connect to a network with hidden SSID in Windows 7

  - by Dor

  I have Windows 7 with the following station: D-Link DWA-160 Xtreme N Dual Band USB Adapter(rev.A2) (driver version 3.5.0.21). I'm trying to connect to a wireless network that has an hidden SSID with the command: Netsh wlan connect name="myNetworkProfile" The profile is configured to connect even if the network is not broadcasting its name (SSID). Despite that, the command fails promptly every time with the message: The network specified by profile "myNetworkProfile" is not available to connect. Nonetheless, when trying to connect manually using the dialog box (see image below), it successfully connects to the network after about 10 or 15 seconds. Also, Please - no need to elaborate about how useless the hidden SSID feature is.

  Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >