Search Results

Search found 1627 results on 66 pages for 'serial'.

Page 59/66 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

• Repeated disconnects on WPA PEAP network

  - by exasperated

  My school has a WPA PEAP network with GTC inner authentication. I am able to connect to the network, but once I load a website or two, the network become unresponsive (i.e. in Chromium, it gets stuck at "Sending request"), and I'm eventually disconnected. Any help will be greatly appreciated. Here's some log output. I can provide more if needed: Ubuntu 13.04 3.8.0-32-generic x86_64 lsusb: 03:00.0 Network controller: Intel Corporation Centrino Advanced-N 6235 (rev 24) lsmod: iwldvm                241872  0  mac80211              606457  1 iwldvm iwlwifi               173516  1 iwldvm cfg80211              511019  3 iwlwifi,mac80211,iwldvm dmesg: [    3.501227] iwlwifi 0000:03:00.0: irq 46 for MSI/MSI-X [    3.503541] iwlwifi 0000:03:00.0: loaded firmware version 18.168.6.1 [    3.527153] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUG disabled [    3.527162] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUGFS enabled [    3.527170] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled [    3.527178] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TESTMODE enabled [    3.527186] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_P2P disabled [    3.527192] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Advanced-N 6235 AGN, REV=0xB0 [    3.527240] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [    3.551049] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [  375.153065] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [  375.159727] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [  375.553201] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [  375.559871] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 1892.110738] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 1892.117357] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5227.235372] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 5227.242122] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5817.817954] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 5817.824560] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5824.571917] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 5824.571929] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 5824.571935] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 6956.290061] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 6956.296671] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 6963.080560] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 6963.080566] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 6963.080570] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 7613.469241] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 7613.475870] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 7620.201265] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 7620.201278] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 7620.201285] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 8232.762453] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 8232.769065] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 8239.581772] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 8239.581784] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 8239.581792] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [13763.634808] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [13763.641427] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [16955.598953] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [16955.605574] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 lshw:    *-network        description: Wireless interface        product: Centrino Advanced-N 6235        vendor: Intel Corporation        physical id: 0        bus info: pci@0000:03:00.0        logical name: wlan0        version: 24        serial: b4:b6:76:a0:4b:3c        width: 64 bits        clock: 33MHz        capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless        configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-32-generic firmware=18.168.6.1 ip=10.250.169.96 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn        resources: irq:46 memory:f7c00000-f7c01fff iwlist scan: Cell 02 - Address: 24:DE:C6:B0:C7:D9                     Channel:36                     Frequency:5.18 GHz (Channel 36)                     Quality=29/70  Signal level=-81 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=0000004ff3fe419b                     Extra: Last beacon: 27820ms ago                     IE: Unknown: 0009436174436861743278                     IE: Unknown: 01088C129824B048606C                     IE: Unknown: 030124                     IE: IEEE 802.11i/WPA2 Version 1                         Group Cipher : CCMP                         Pairwise Ciphers (1) : CCMP                         Authentication Suites (1) : 802.1x                     IE: Unknown: 2D1ACC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: 3D1624001B000000FF000000000000000000000000000000                     IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00                     IE: Unknown: DD1E00904C33CC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: DD1A00904C3424001B000000FF000000000000000000000000000000           Cell 04 - Address: 24:DE:C6:B0:C3:E9                     Channel:149                     Frequency:5.745 GHz                     Quality=28/70  Signal level=-82 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=000000181f60e19c                     Extra: Last beacon: 28680ms ago                     IE: Unknown: 0009436174436861743278                     IE: Unknown: 01088C129824B048606C                     IE: Unknown: 030195                     IE: Unknown: 050400010000                     IE: IEEE 802.11i/WPA2 Version 1                         Group Cipher : CCMP                         Pairwise Ciphers (1) : CCMP                         Authentication Suites (1) : 802.1x                     IE: Unknown: 2D1ACC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: 3D1695001B000000FF000000000000000000000000000000                     IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00                     IE: Unknown: DD1E00904C33CC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: DD1A00904C3495001B000000FF000000000000000000000000000000                     IE: Unknown: DD07000B8601040817                     IE: Unknown: DD0E000B860103006170313930333032           Cell 09 - Address: 24:DE:C6:B0:C0:29                     Channel:149                     Frequency:5.745 GHz                     Quality=39/70  Signal level=-71 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=00000112fb688ede                     Extra: Last beacon: 27716ms ago ifconfig (while connected): wlan0     Link encap:Ethernet  HWaddr b4:b6:76:a0:4b:3c             inet addr:10.250.16.220  Bcast:10.250.31.255  Mask:255.255.240.0           inet6 addr: fe80::b6b6:76ff:fea0:4b3c/64 Scope:Link           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1           RX packets:230023 errors:0 dropped:0 overruns:0 frame:0           TX packets:130970 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:1000            RX bytes:255999759 (255.9 MB)  TX bytes:16652605 (16.6 MB) iwconfig (while connected): wlan0     IEEE 802.11abgn  ESSID:"CatChat2x"             Mode:Managed  Frequency:5.745 GHz  Access Point: 24:DE:C6:B0:C0:29              Bit Rate=6 Mb/s   Tx-Power=15 dBm              Retry  long limit:7   RTS thr:off   Fragment thr:off           Power Management:off           Link Quality=36/70  Signal level=-74 dBm             Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0           Tx excessive retries:0  Invalid misc:3   Missed beacon:0

  Read the article

• Unable to boot: Missing Operating system

  - by Vivek S Panicker

  i had installed Ubuntu 11.10 along with the another Ubuntu 11.10 which already installed in my netbook. Later I formatted the partition I newly installed. Next time when I boot it went to Grub Rescue menu. I boot my system again with Ubuntu USB stick, Then I installed Boot repair package in USB and restored MBR and GRUB menu in hard disk. Now when I am restarting, I am getting a message Missing operating system, press any key to continue. Can somebody help me on this? Below is the output for sudo fdisk -l omitting empty partition (7) Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00058a60 Device Boot Start End Blocks Id System /dev/sda1 * 2048 204072287 102035120 83 Linux /dev/sda2 204072958 312580095 54253569 5 Extended /dev/sda5 310507520 312580095 1036288 82 Linux swap / Solaris /dev/sda6 308432896 310503423 1035264 82 Linux swap / Solaris Partition table entries are not in disk order Disk /dev/sdb: 4006 MB, 4006608896 bytes 124 heads, 62 sectors/track, 1017 cylinders, total 7825408 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004d3df Device Boot Start End Blocks Id System /dev/sdb1 * 62 7818695 3909317 b W95 FAT32 Below is the output for sudo blkid /dev/loop0: TYPE="squashfs" /dev/loop1: LABEL="casper-rw" UUID="533defb1-f073-254a-b46f-7ca0ac1f4e0c" TYPE="ext2" /dev/sda1: LABEL="Ubuntu" UUID="6a141040-3ba8-457a-9de5-ad06e6057084" TYPE="ext4" /dev/sda5: UUID="3a7f62d6-9c65-4d12-a3b6-5d62b9710f7d" TYPE="swap" /dev/sda6: UUID="274da115-cec2-4418-a1af-88fe921e3670" TYPE="swap" /dev/sdb1: LABEL="PENDRIVE" UUID="EC22-6BE4" TYPE="vfat" File /boot/grub/grub.cfg # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 6a141040-3ba8-457a-9de5-ad06e6057084 if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 6a141040-3ba8-457a-9de5-ad06e6057084 set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=10 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 3.0.0-12-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 6a141040-3ba8-457a-9de5-ad06e6057084 linux /boot/vmlinuz-3.0.0-12-generic root=UUID=6a141040-3ba8-457a-9de5-ad06e6057084 ro quiet splash vt.handoff=7 initrd /boot/initrd.img-3.0.0-12-generic } menuentry 'Ubuntu, with Linux 3.0.0-12-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 6a141040-3ba8-457a-9de5-ad06e6057084 echo 'Loading Linux 3.0.0-12-generic ...' linux /boot/vmlinuz-3.0.0-12-generic root=UUID=6a141040-3ba8-457a-9de5-ad06e6057084 ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.0.0-12-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 6a141040-3ba8-457a-9de5-ad06e6057084 linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 6a141040-3ba8-457a-9de5-ad06e6057084 linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ###

  Read the article

• Can't see my partitions after grub recovery

  - by dimbo

  I stupidly inserted the windows CD into my dual boot Ubuntu 11.10 / windows xp system. I just wanted to see if I could install windows on my external usb HD, but didn't actually go ahead with the install. It seems like the windows CD messed up my MBR and I had to use boot-repair and the ubuntu 11.10 live CD to gain access to ubuntu again. It seems to boot up a little differently (slower) but works. However, I now cant see any of my partitions in nautilus (there are 3). When I open gparted, it just shows my whole hard drive as unallocated (I know it has a windows partition that works and my ubuntu partition that I am using now). If I insert a usb pen, it is also not visible in nautilus but in gparted shows up as a FAT32 partition (which is correct although I cannot access it). sudo fdisk -l gives the following : demian@dimbo-TP:~$ sudo fdisk -l [sudo] password for demian: omitting empty partition (5) Disk /dev/sda: 320.1 GB, 320072933376 bytes 240 heads, 63 sectors/track, 41345 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x877b877b Device Boot Start End Blocks Id System /dev/sda1 * 63 63842309 31921123+ 7 HPFS/NTFS/exFAT /dev/sda2 63844350 133484084 34819867+ 5 Extended /dev/sda3 127636488 133484084 2923798+ 82 Linux swap / Solaris /dev/sda4 133484085 625137344 245826630 83 Linux /dev/sda5 63844352 123445247 29800448 83 Linux /dev/sda6 123447296 127635455 2094080 82 Linux swap / Solaris Disk /dev/sdb: 8100 MB, 8100249600 bytes 12 heads, 40 sectors/track, 32960 cylinders, total 15820800 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdb1 * 5992 15820799 7907404 c W95 FAT32 (LBA) Here is my grub.conf file. Like I said before, I had to use the 'boot-repair' utility with the live cd to get grub working again. I think that this utility maybe created a new grub for me because the startup is definitely not the same. The screen goes blank for a while, and then the ubuntu loading dots come up for a brief moment (instead of during the whole startup process) before the dektop is displayed. Anyway : # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=10 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 3.0.0-12-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a linux /boot/vmlinuz-3.0.0-12-generic root=UUID=5349ff67-b7b7-489f-a881-ae49c1dcd84a ro quiet splash vt.handoff=7 initrd /boot/initrd.img-3.0.0-12-generic } menuentry 'Ubuntu, with Linux 3.0.0-12-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a echo 'Loading Linux 3.0.0-12-generic ...' linux /boot/vmlinuz-3.0.0-12-generic root=UUID=5349ff67-b7b7-489f-a881-ae49c1dcd84a ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.0.0-12-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Microsoft Windows XP Professional (on /dev/sda1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 72A89361A89322A1 drivemap -s (hd0) ${root} chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### How can I get things back to normal. Thanks, Demian.

  Read the article

• Stepping outside Visual Studio IDE [Part 1 of 2] with Eclipse

  - by mbcrump

  “If you're walking down the right path and you're willing to keep walking, eventually you'll make progress." – Barack Obama In my quest to become a better programmer, I’ve decided to start the process of learning Java. I will be primary using the Eclipse Language IDE. I will not bore you with the history just what is needed for a .NET developer to get up and running. I will provide links, screenshots and a few brief code tutorials. Links to documentation. The Official Eclipse FAQ’s Links to binaries. Eclipse IDE for Java EE Developers the Galileo Package (based on Eclipse 3.5 SR2)  Sun Developer Network – Java Eclipse officially recommends Java version 5 (also known as 1.5), although many Eclipse users use the newer version 6 (1.6). That's it, nothing more is required except to compile and run java. Installation Unzip the Eclipse IDE for Java EE Developers and double click the file named Eclipse.exe. You will probably want to create a link for it on your desktop. Once, it’s installed and launched you will have to select a workspace. Just accept the defaults and you will see the following: Lets go ahead and write a simple program. To write a "Hello World" program follow these steps: Start Eclipse. Create a new Java Project: File->New->Project. Select "Java" in the category list. Select "Java Project" in the project list. Click "Next". Enter a project name into the Project name field, for example, "HW Project". Click "Finish" Allow it to open the Java perspective Create a new Java class: Click the "Create a Java Class" button in the toolbar. (This is the icon below "Run" and "Window" with a tooltip that says "New Java Class.") Enter "HW" into the Name field. Click the checkbox indicating that you would like Eclipse to create a "public static void main(String[] args)" method. Click "Finish". A Java editor for HW.java will open. In the main method enter the following line.      System.out.println("This is my first java program and btw Hello World"); Save using ctrl-s. This automatically compiles HW.java. Click the "Run" button in the toolbar (looks like a VCR play button). You will be prompted to create a Launch configuration. Select "Java Application" and click "New". Click "Run" to run the Hello World program. The console will open and display "This is my first java program and btw Hello World". You now have your first java program, lets go ahead and make an applet. Since you already have the HW.java open, click inside the window and remove all code. Now copy/paste the following code snippet. Java Code Snippet for an applet. 1: import java.applet.Applet; 2: import java.awt.Graphics; 3: import java.awt.Color; 4:  5: @SuppressWarnings("serial") 6: public class HelloWorld extends Applet{ 7:  8: String text = "I'm a simple applet"; 9:  10: public void init() { 11: text = "I'm a simple applet"; 12: setBackground(Color.GREEN); 13: } 14:  15: public void start() { 16: System.out.println("starting..."); 17: } 18:  19: public void stop() { 20: System.out.println("stopping..."); 21: } 22:  23: public void destroy() { 24: System.out.println("preparing to unload..."); 25: } 26:  27: public void paint(Graphics g){ 28: System.out.println("Paint"); 29: g.setColor(Color.blue); 30: g.drawRect(0, 0, 31: getSize().width -1, 32: getSize().height -1); 33: g.setColor(Color.black); 34: g.drawString(text, 15, 25); 35: } 36: } The Eclipse IDE should look like Click "Run" to run the Hello World applet. Now, lets test our new java applet. So, navigate over to your workspace for example: “C:\Users\mbcrump\workspace\HW Project\bin” and you should see 2 files. HW.class java.policy.applet Create a HTML page with the following code: 1: <HTML> 2: <BODY> 3: <APPLET CODE=HW.class WIDTH=200 HEIGHT=100> 4: </APPLET> 5: </BODY> 6: </HTML> Open, the HTML page in Firefox or IE and you will see your applet running.  I hope this brief look at the Eclipse IDE helps someone get acquainted with Java Development. Even if your full time gig is with .NET, it will not hurt to have another language in your tool belt. As always, I welcome any suggestions or comments.

  Read the article

• Why won't USB 3.0 external hard drive run at USB 3.0 speeds?

  - by jgottula

  I recently purchased a PCI Express x1 USB 3.0 controller card (containing the NEC USB 3.0 controller) with the intent of using a USB 3.0 external hard drive with my Linux box. I installed the card in an empty PCIe slot on my motherboard, connected the card to a power cable, strung a USB 3.0 cable between one of the new ports and my external HDD, and connected the HDD to a wall socket for power. Booting the system, the drive works 100% as intended, with the one exception of throughput: rather than using SuperSpeed 4.8 Gbps connectivity, it seems to be falling back to High Speed 480 Mbps USB 2.0-style throughput. Disk Utility shows it as a 480 Mbps device, and running a couple Disk Utility and dd benchmarks confirms that the drive fails to exceed ~40 MB/s (the approximate limit of USB 2.0), despite it being an SSD capable of far more than that. When I connect my USB 3.0 HDD, dmesg shows this: [ 3923.280018] usb 3-2: new high speed USB device using ehci_hcd and address 6 where I would expect to find this: [ 3923.280018] usb 3-2: new SuperSpeed USB device using xhci_hcd and address 6 My system was running on kernel 2.6.35-25-generic at the time. Then, I stumbled upon this forum thread by an individual who found that a bug, which was present in kernels prior to 2.6.37-rc5, could be the culprit for this type of problem. Consequently, I installed the 2.6.37-generic mainline Ubuntu kernel to determine if the problem would go away. It didn't, so I tried 2.6.38-rc3-generic, and even the 2.6.38 nightly from 2010.02.01, to no avail. In short, I'm trying to determine why, with USB 3.0 support in the kernel, my USB 3.0 drive fails to run at full SuperSpeed throughput. See the comments under this question for additional details. Output that might be relevant to the problem (when booting from 2.6.38-rc3): Relevant lines from dmesg: [ 19.589491] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 19.589512] xhci_hcd 0000:03:00.0: setting latency timer to 64 [ 19.589516] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 19.589623] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 12 [ 19.650492] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf8100000 [ 19.650556] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X [ 19.650560] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X [ 19.650563] xhci_hcd 0000:03:00.0: irq 49 for MSI/MSI-X [ 19.653946] xHCI xhci_add_endpoint called for root hub [ 19.653948] xHCI xhci_check_bandwidth called for root hub Relevant section of sudo lspci -v: 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd Relevant section of sudo lsusb -v: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.38-020638rc3-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:03:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Full, non-verbose lsusb: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 003: ID 04d9:0702 Holtek Semiconductor, Inc. Bus 009 Device 002: ID 046d:c068 Logitech, Inc. G500 Laser Mouse Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 006: ID 174c:5106 ASMedia Technology Inc. Bus 003 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader) Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 006: ID 1687:0163 Kingmax Digital Inc. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 046d:081b Logitech, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Full output: full dmesg full lspci full lsusb

  Read the article

• www.domain redirecting to google?

  - by aayush

  Note: A while back i had no place to host my domain, then via namecheap i set it to forward my domain to google I bought webhosting again today and everything was working fine. I set up vhosts and set up www.domain as the server alias. Both worked. Then i tried to set up a alternate subdomain test.domain, but failed (I did it by creating a alternate vhost right below the current one) as it kept redirecting to google. As a test, i replaced the www with test in serveralias, it still redirected to google but now even www redirects to google. I am using cloudflare, and i am really confused how to go about this. I tried listing www as a cname and as a A record, still redirecting to google. I tried checking via proxies e.t.c, its universal and hence not a problem of my PC. Please help, i am really distressed by this. I am running a ubuntu 13.10 x32 stack with LAMP. Here is what my domain.com.conf file looks like <VirtualHost *:80> # The ServerName directive sets the request scheme, hostname and port that # the server uses to identify itself. This is used when creating # redirection URLs. In the context of virtual hosts, the ServerName # specifies what hostname must appear in the request's Host: header to # match this virtual host. For the default virtual host (this file) this # value is not decisive as it is used as a last resort host regardless. # However, you must set it for any further virtual host explicitly. ServerName domain.com ServerAlias www.domain.com ServerAdmin webmaster@localhost DocumentRoot /var/www/domain.com/public_html # Available loglevels: trace8, ..., trace1, debug, info, notice, warn, # error, crit, alert, emerg. # It is also possible to configure the loglevel for particular # modules, e.g. #LogLevel info ssl:warn ErrorLog ${APACHE_LOG_DIR}/error.log CustomLog ${APACHE_LOG_DIR}/access.log combined # For most configuration files from conf-available/, which are # enabled or disabled at a global level, it is possible to # include a line for only one particular virtual host. For example the # following line enables the CGI configuration for this host only # after it has been globally disabled with "a2disconf". #Include conf-available/serve-cgi-bin.conf </VirtualHost> There is a valid index.php file at the end of the documentroot aswell. The website in question is aayushagra.com Edit: On cloudflare i tried removing the www entirely, and it still sent me to google Edit: Zone file ;; Domain: aayushagra.com ;; Exported: 2013-11-03 07:37:52 ;; ;; This file is intended for use for informational and archival ;; purposes ONLY and MUST be edited before use on a production ;; DNS server. In particular, you must: ;; -- update the SOA record with the correct authoritative name server ;; -- update the SOA record with the contact e-mail address information ;; -- update the NS record(s) with the authoritative name servers for this domain. ;; ;; For further information, please consult the BIND documentation ;; located on the following website: ;; ;; http://www.isc.org/ ;; ;; And RFC 1035: ;; ;; http://www.ietf.org/rfc/rfc1035.txt ;; ;; Please note that we do NOT offer technical support for any use ;; of this zone data, the BIND name server, or any other third-party ;; DNS software. ;; ;; Use at your own risk. ;; $ORIGIN aayushagra.com. @ 3600 IN SOA aayushagra.com. root.aayushagra.com. ( 2013110301 ; serial 7200 ; refresh 3600 ; retry 86400 ; expire 3600) ; minimum ;; MX Records aayushagra.com. 300 IN MX aayushagra.com. ;; CNAME Records direct.aayushagra.com. 300 IN CNAME aayushagra.com. ;; A Records (IPv4 addresses) www.aayushagra.com. 300 IN A 146.185.140.31 aayushagra.com. 300 IN A 146.185.140.31

  Read the article

• Grub won't boot windows after update from 11.10 to 12.04

  - by Holger

  thanks for your time and reading this, here's the deal: i upgraded from 11.10 to 12.04 and everything worked out until i rebooted, i had 11.10 sucessfully running as a dual boot with windows vista. when i rebooted, my GRUB was shot to hell, what ever option i selected it said partion not found or something similar... booting into a live version on a thumb drive and running bootrepair from there fixed the issue... but only for ubuntu, when i try to boot into windows it only goes back to GRUB. i'm not at home, and heres a list of what i have here with me... 1 4gb thumb drive, empty 1 8gb thumb drive, windows vista installer bootable 1 old laptop, the one i try to save, optical drive is not existent 2 Mbps internet connection can you help me get back into my windows without having to reinstall windows? or at least show me a way how to use my illustrator through a virtual machine or something? here's my grub cfg # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root 1063e402-b14f-45e5-92b6-d20a2e3a717e if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root 1063e402-b14f-45e5-92b6-d20a2e3a717e set locale_dir=($root)/boot/grub/locale set lang=de_DE insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="${1}" if [ "${1}" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ "${recordfail}" != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "${linux_gfx_mode}" != "text" ]; then load_video; fi menuentry 'Ubuntu, mit Linux 3.2.0-24-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root 1063e402-b14f-45e5-92b6-d20a2e3a717e linux /boot/vmlinuz-3.2.0-24-generic root=UUID=1063e402-b14f-45e5-92b6-d20a2e3a717e ro quiet splash $vt_handoff initrd /boot/initrd.img-3.2.0-24-generic } menuentry 'Ubuntu, mit Linux 3.2.0-24-generic (Wiederherstellungsmodus)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root 1063e402-b14f-45e5-92b6-d20a2e3a717e echo 'Linux 3.2.0-24-generic wird geladen …' linux /boot/vmlinuz-3.2.0-24-generic root=UUID=1063e402-b14f-45e5-92b6-d20a2e3a717e ro recovery nomodeset echo 'Initiale Ramdisk wird geladen …' initrd /boot/initrd.img-3.2.0-24-generic } submenu "Previous Linux versions" { menuentry 'Ubuntu, mit Linux 3.0.0-19-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root 1063e402-b14f-45e5-92b6-d20a2e3a717e linux /boot/vmlinuz-3.0.0-19-generic root=UUID=1063e402-b14f-45e5-92b6-d20a2e3a717e ro quiet splash $vt_handoff initrd /boot/initrd.img-3.0.0-19-generic } menuentry 'Ubuntu, mit Linux 3.0.0-19-generic (Wiederherstellungsmodus)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root 1063e402-b14f-45e5-92b6-d20a2e3a717e echo 'Linux 3.0.0-19-generic wird geladen …' linux /boot/vmlinuz-3.0.0-19-generic root=UUID=1063e402-b14f-45e5-92b6-d20a2e3a717e ro recovery nomodeset echo 'Initiale Ramdisk wird geladen …' initrd /boot/initrd.img-3.0.0-19-generic } } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root 1063e402-b14f-45e5-92b6-d20a2e3a717e linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root 1063e402-b14f-45e5-92b6-d20a2e3a717e linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows Vista (loader) (on /dev/sda1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 2C9E66B39E6674EC chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ###

  Read the article

• Can't control connection bit rate using iwconfig with Atheros TL-WN821N (AR7010)

  - by Paul H

  I'm trying to reduce the connection bit rate on my Atheros TP-Link TL-WN821N v3 usb wifi adapter due to frequent instability issues (reported connection speed goes down to 1Mb/s and I have to physically reconnect the adapter to regain a connection). I know this is a common problem with this device, and I have tried everything I can think of to fix it, including using drivers from linux-backports; compiling and installing a custom firmware (following instructions on https://wiki.debian.org/ath9k_htc#fw-free) and (as a last resort) using ndiswrapper. When using ndiswrapper, the wifi adapter is stable and operates in g mode at 54Mb/s (whilst when using the default ath9k_htc module, the adapter connects in n mode and the bit rate fluctuates constantly). Unfortunately, with this setup I have to run my processor using only one core, since using SMP with ndiswrapper causes a kernel oops on my system. So I want to lock my bit rate to 54Mb/s (or less, if need be) for connection stability, using the ath9k_htc module. I've tried 'sudo iwconfig wlan0 rate 54M'; the command runs with no error but when I check the bit rate with 'sudo iwlist wlan0 bitrate' the command returns: wlan0 unknown bit-rate information. Current Bit Rate:78 Mb/s Any ideas? Here's some info (hopefully relevant) on my setup: Xubuntu (12.04.3) 64bit (kernel 3.2.0-55.85-generic) using Network Manager. My Router is from Virgin Media, the VMDG480. lshw -C network : *-network description: Wireless interface physical id: 1 bus info: usb@1:4 logical name: wlan0 serial: 74:ea:3a:8f:16:b6 capabilities: ethernet physical wireless configuration: broadcast=yes driver=ath9k_htc driverversion=3.2.0-55 firmware=1.3 ip=192.168.0.9 link=yes multicast=yes wireless=IEEE 802.11bgn lsusb -v: Bus 001 Device 003: ID 0cf3:7015 Atheros Communications, Inc. TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 idVendor 0x0cf3 Atheros Communications, Inc. idProduct 0x7015 TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] bcdDevice 2.02 iManufacturer 16 ATHEROS iProduct 32 UB95 iSerial 48 12345 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 60 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 6 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x06 EP 6 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) iwlist wlan0 scanning: wlan0 Scan completed : Cell 01 - Address: C4:3D:C7:3A:1F:5D Channel:1 Frequency:2.412 GHz (Channel 1) Quality=37/70 Signal level=-73 dBm Encryption key:on ESSID:"my essid" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Master Extra:tsf=00000070cca77186 Extra: Last beacon: 5588ms ago IE: Unknown: 0007756E69636F726E IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 32040C121860 IE: Unknown: 2D1AFC181BFFFF000000000000000000000000000000000000000000 IE: Unknown: 3D1601080400000000000000000000000000000000000000 IE: Unknown: DD7E0050F204104A0001101044000102103B00010310470010F99C335D7BAC57FB00137DFA79600220102100074E657467656172102300074E6574676561721024000631323334353610420007303030303030311054000800060050F20400011011000743473331303144100800022008103C0001011049000600372A000120 IE: Unknown: DD090010180203F02C0000 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 iwconfig: lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"my essid" Mode:Managed Frequency:2.412 GHz Access Point: C4:3D:C7:3A:1F:5D Bit Rate=78 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0,

  Read the article

• Getting problem while capturing image through web cam in Java -OpenCV code.

  - by Chetan

  Hi.. I am developing Face detector using OpenCV library in java... I have written sample code for this,but it is giving Error while capturing image. can any one help please. Here is the code import java.awt.; import java.awt.event.; import java.awt.image.MemoryImageSource; import hypermedia.video.OpenCV; @SuppressWarnings("serial") public class FaceDetection extends Frame implements Runnable { ///Main method. public static void main(String[] args) { //System.out.println( "\nOpenCV face detection sample\n" ); new FaceDetection(); } // program execution frame rate (millisecond) final int FRAME_RATE = 1000/30; OpenCV cv = null; // OpenCV Object Thread t = null; // the sample thread // the input video stream image Image frame = null; // list of all face detected area Rectangle[] squares = new Rectangle[0]; //** Setup Frame and Object(s). FaceDetection() { super( "Face Detection" ); // OpenCV setup cv = new OpenCV(); //cv.capture(1, 1, 100); cv.capture( 320, 240 ); cv.cascade( OpenCV.CASCADE_FRONTALFACE_ALT ); // frame setup this.setBounds( 100, 100, cv.width, cv.height ); this.setBackground( Color.BLACK ); this.setVisible( true ); this.addKeyListener( new KeyAdapter() { public void keyReleased( KeyEvent e ) { if ( e.getKeyCode()==KeyEvent.VK_ESCAPE ) { // ESC : release OpenCV resources cv.dispose(); System.exit(0); } } } ); // start running program t = new Thread( this ); t.start(); } // Draw video frame and each detected faces area. public void paint( Graphics g ) { // draw image g.drawImage( frame, 0, 0, null ); // draw squares g.setColor( Color.RED ); for( Rectangle rect : squares ) g.drawRect( rect.x, rect.y, rect.width, rect.height ); } @SuppressWarnings("static-access") public void run() { while( t!=null && cv!=null ) { try { t.sleep( FRAME_RATE ); // grab image from video stream cv.read(); // create a new image from cv pixels data MemoryImageSource mis = new MemoryImageSource( cv.width, cv.height, cv.pixels(), 0, cv.width ); frame = createImage( mis ); // detect faces squares = cv.detect( 1.2f, 2, OpenCV.HAAR_DO_CANNY_PRUNING, 20, 20 ); // of course, repaint repaint(); } catch( InterruptedException e ) {;} } } } Error while starting capture : device 0

  Read the article

• Eclipselink read complex object model in an ordered way

  - by Raven

  Hi, I need to read a complex model in an ordered way with eclipselink. The order is mandantory because it is a huge database and I want to have an output of a small portion of the database in a jface tableview. Trying to reorder it in the loading/quering thread takes too long and ordering it in the LabelProvider blocks the UI thread too much time, so I thought if Eclipselink could be used that way, that the database will order it, it might give me the performance I need. Unfortunately the object model can not be changed :-( The model is something like: @SuppressWarnings("serial") @Entity public class Thing implements Serializable { @Id @GeneratedValue(strategy = GenerationType.TABLE) private int id; private String name; @OneToMany(cascade=CascadeType.ALL) @PrivateOwned private List<Property> properties = new ArrayList<Property>(); ... // getter and setter following here } public class Property implements Serializable { @Id @GeneratedValue(strategy = GenerationType.TABLE) private int id; @OneToOne private Item item; private String value; ... // getter and setter following here } public class Item implements Serializable { @Id @GeneratedValue(strategy = GenerationType.TABLE) private int id; private String name; .... // getter and setter following here } // Code end In the table view the y-axis is more or less created with the query Query q = em.createQuery("SELECT m FROM Thing m ORDER BY m.name ASC"); using the "name" attribute from the Thing objects as label. In the table view the x-axis is more or less created with the query Query q = em.createQuery("SELECT m FROM Item m ORDER BY m.name ASC"); using the "name" attribute from the Item objects as label. Each cell has the value Things.getProperties().get[x].getValue() Unfortunately the list "properties" is not ordered, so the combination of cell value and x-axis column number (x) is not necessarily correct. Therefore I need to order the list "properties" in the same way as I ordered the labeling of the x-axis. And exactly this is the thing I dont know how it is done. So querying for the Thing objects should return the list "properties" "ORDER BY name ASC" but of the "Item"s objects. My ideas are something like having a query with two JOINs. Joing Things with Property and with Item but somehow I was unable to get it to work yet. Thank you for your help and your ideas to solve this riddle.

  Read the article

• Please Explain Drupal schema and drupal_write_record

  - by Aaron

  Hi. A few questions. 1) Where is the best place to populate a new database table when a module is first installed, enabled? I need to go and get some data from an external source and want to do it transparently when the user installs/enables my custom module. I create the schema in {mymodule}_schema(), do drupal_install_schema({tablename}); in hook_install. Then I try to populate the table in hook_enable using drupal_write_record. I confirmed the table was created, I get no errors when hook_enable executes, but when I query the new table, I get no rows back--it's empty. Here's one variation of the code I've tried: /** * Implementation of hook_schema() */ function ncbi_subsites_schema() { // we know it's MYSQL, so no need to check $schema['ncbi_subsites_sites'] = array( 'description' => 'The base table for subsites', 'fields' => array( 'site_id' => array( 'description' => 'Primary id for site', 'type' => 'serial', 'unsigned' => TRUE, 'not null' => TRUE, ), // end site_id 'title' => array( 'description' => 'The title of the subsite', 'type' => 'varchar', 'length' => 255, 'not null' => TRUE, 'default' => '', ), //end title field 'url' => array( 'description' => 'The URL of the subsite in Production', 'type' => 'varchar', 'length' => 255, 'default' => '', ), //end url field ), //end fields 'unique keys' => array( 'site_id'=> array('site_id'), 'title' => array('title'), ), //end unique keys 'primary_key' => array('site_id'), ); // end schema return $schema; } Here's hook_install: function ncbi_subsites_install() { drupal_install_schema('ncbi_subsites'); } Here's hook_enable: function ncbi_subsites_enable() { drupal_get_schema('ncbi_subsites_site'); // my helper function to get data for table (not shown) $subsites = ncbi_subsites_get_subsites(); foreach( $subsites as $name=>$attrs ) { $record = new stdClass(); $record->title = $name; $record->url = $attrs['homepage']; drupal_write_record( 'ncbi_subsites_sites', $record ); } } Can someone tell me what I'm missing?

  Read the article

• Securing a license key with RSA key.

  - by Jesse Knott

  Hello, it's late, I'm tired, and probably being quite dense.... I have written an application that I need to secure so it will only run on machines that I generate a key for. What I am doing for now is getting the BIOS serial number and generating a hash from that, I then am encrypting it using a XML RSA private key. I then sign the XML to ensure that it is not tampered with. I am trying to package the public key to decrypt and verify the signature with, but every time I try to execute the code as a different user than the one that generated the signature I get a failure on the signature. Most of my code is modified from sample code I have found since I am not as familiar with RSA encryption as I would like to be. Below is the code I was using and the code I thought I needed to use to get this working right... Any feedback would be greatly appreciated as I am quite lost at this point the original code I was working with was this, this code works fine as long as the user launching the program is the same one that signed the document originally... CspParameters cspParams = new CspParameters(); cspParams.KeyContainerName = "XML_DSIG_RSA_KEY"; cspParams.Flags = CspProviderFlags.UseMachineKeyStore; // Create a new RSA signing key and save it in the container. RSACryptoServiceProvider rsaKey = new RSACryptoServiceProvider(cspParams) { PersistKeyInCsp = true, }; This code is what I believe I should be doing but it's failing to verify the signature no matter what I do, regardless if it's the same user or a different one... RSACryptoServiceProvider rsaKey = new RSACryptoServiceProvider(); //Load the private key from xml file XmlDocument xmlPrivateKey = new XmlDocument(); xmlPrivateKey.Load("KeyPriv.xml"); rsaKey.FromXmlString(xmlPrivateKey.InnerXml); I believe this to have something to do with the key container name (Being a real dumbass here please excuse me) I am quite certain that this is the line that is both causing it to work in the first case and preventing it from working in the second case.... cspParams.KeyContainerName = "XML_DSIG_RSA_KEY"; Is there a way for me to sign/encrypt the XML with a private key when the application license is generated and then drop the public key in the app directory and use that to verify/decrypt the code? I can drop the encryption part if I can get the signature part working right. I was using it as a backup to obfuscate the origin of the license code I am keying from. Does any of this make sense? Am I a total dunce? Thanks for any help anyone can give me in this..

  Read the article

• Eclipselink read complex oject model in an ordered way

  - by Raven

  Hi, I need to read a complex model in an ordered way with eclipselink. The order is mandantory because it is a huge database and I want to have an output of a small portion of the database in a jface tableview. Trying to reorder it in the loading/quering thread takes too long and ordering it in the LabelProvider blocks the UI thread too much time, so I thought if Eclipselink could be used that way, that the database will order it, it might give me the performance I need. Unfortunately the object model can not be changed :-( The model is something like: @SuppressWarnings("serial") @Entity public class Thing implements Serializable { @Id @GeneratedValue(strategy = GenerationType.TABLE) private int id; private String name; @OneToMany(cascade=CascadeType.ALL) @PrivateOwned private List<Property> properties = new ArrayList<Property>(); ... // getter and setter following here } public class Property implements Serializable { @Id @GeneratedValue(strategy = GenerationType.TABLE) private int id; @OneToOne private Item item; private String value; ... // getter and setter following here } public class Item implements Serializable { @Id @GeneratedValue(strategy = GenerationType.TABLE) private int id; private String name; .... // getter and setter following here } // Code end In the table view the y-axis is more or less created with the query Query q = em.createQuery("SELECT m FROM Thing m ORDER BY m.name ASC"); using the "name" attribute from the Thing objects as label. In the table view the x-axis is more or less created with the query Query q = em.createQuery("SELECT m FROM Item m ORDER BY m.name ASC"); using the "name" attribute from the Item objects as label. Each cell has the value Things.getProperties().get[x].getValue() Unfortunately the list "properties" is not ordered, so the combination of cell value and x-axis column number (x) is not necessarily correct. Therefore I need to order the list "properties" in the same way as I ordered the labeling of the x-axis. And exactly this is the thing I dont know how it is done. So querying for the Thing objects should return the list "properties" "ORDER BY name ASC" but of the "Item"s objects. My ideas are something like having a query with two JOINs. Joing Things with Property and with Item but somehow I was unable to get it to work yet. Thank you for your help and your ideas to solve this riddle.

  Read the article

• dynamic char array sizing

  - by droseman

  Hello, In my application, I have a char array defined which can take one of three options: "okay", "high", "low" which are then sent down a serial port to a remote device. I currently have the array sized to take the 4 character words plus carriage return and line feed, but when I have to send "low" I get a null character in the strings, which I am concerned would confuse the host terminal. array definition char mod1_status_char[6] = {'0','0','0','0','0','0'}; char mod2_status_char[6] = {'0','0','0','0','0','0'}; char mod3_status_char[6] = {'0','0','0','0','0','0'}; sample of switch case statement: void DCOKStatus(uint8_t *ptr_status) { uint8_t status = *ptr_status; switch (status) { case 0x00: strcpy(mod1_status_char, "okay"); strcpy(mod2_status_char, "okay"); strcpy(mod3_status_char, "okay"); break; case 0x10: strcpy(mod1_status_char, "okay"); strcpy(mod2_status_char, "okay"); strcpy(mod3_status_char, "low"); break; } This is the struct which makes the message string to send strcpy(MsgStatus_on.descriptor_msg, "$psu_"); MsgStatus_on.address01 = hex_addr[0]; MsgStatus_on.address02 = hex_addr[1]; MsgStatus_on.space01 = 0x20; strcpy(MsgStatus_on.cmdmsg01, "op_en op1_"); strcpy(MsgStatus_on.statusmsg01, mod1_status_char); MsgStatus_on.space02 = 0x20; strcpy(MsgStatus_on.cmdmsg02, "op2_"); strcpy(MsgStatus_on.statusmsg02, mod2_status_char); MsgStatus_on.space03 = 0x20; strcpy(MsgStatus_on.cmdmsg03, "op3_"); strcpy(MsgStatus_on.statusmsg03, mod3_status_char); MsgStatus_on.CR = 0x0D; MsgStatus_on.LF = 0x0A; and this sends the message void USARTWrite(char *object, uint32_t size) { GPIO_SetBits(GPIOB, GPIO_Pin_1); char *byte; for (byte = object; size--; ++byte) { USART_SendData(USART1,*byte); } Would anyone be able to suggest a good approach to dynamically size the array to one character shorter when I need to send "low"? Thanks

  Read the article

• How to delegate SwingWorker's publish to other methods

  - by Savvas Dalkitsis

  My "problem" can be described by the following. Assume we have an intensive process that we want to have running in the background and have it update a Swing JProgress bar. The solution is easy: import java.util.List; import javax.swing.JOptionPane; import javax.swing.JProgressBar; import javax.swing.SwingWorker; /** * @author Savvas Dalkitsis */ public class Test { public static void main(String[] args) { final JProgressBar progressBar = new JProgressBar(0,99); SwingWorker<Void, Integer> w = new SwingWorker<Void, Integer>(){ @Override protected void process(List<Integer> chunks) { progressBar.setValue(chunks.get(chunks.size()-1)); } @Override protected Void doInBackground() throws Exception { for (int i=0;i<100;i++) { publish(i); Thread.sleep(300); } return null; } }; w.execute(); JOptionPane.showOptionDialog(null, new Object[] { "Process", progressBar }, "Process", JOptionPane.OK_CANCEL_OPTION, JOptionPane.QUESTION_MESSAGE, null, null, null); } } Now assume that i have various methods that take a long time. For instance we have a method that downloads a file from a server. Or another that uploads to a server. Or anything really. What is the proper way of delegating the publish method to those methods so that they can update the GUI appropriately? What i have found so far is this (assume that the method "aMethod" resides in some other package for instance): import java.awt.event.ActionEvent; import java.util.List; import javax.swing.AbstractAction; import javax.swing.Action; import javax.swing.JOptionPane; import javax.swing.JProgressBar; import javax.swing.SwingWorker; /** * @author Savvas Dalkitsis */ public class Test { public static void main(String[] args) { final JProgressBar progressBar = new JProgressBar(0,99); SwingWorker<Void, Integer> w = new SwingWorker<Void, Integer>(){ @Override protected void process(List<Integer> chunks) { progressBar.setValue(chunks.get(chunks.size()-1)); } @SuppressWarnings("serial") @Override protected Void doInBackground() throws Exception { aMethod(new AbstractAction() { @Override public void actionPerformed(ActionEvent e) { publish((Integer)getValue("progress")); } }); return null; } }; w.execute(); JOptionPane.showOptionDialog(null, new Object[] { "Process", progressBar }, "Process", JOptionPane.OK_CANCEL_OPTION, JOptionPane.QUESTION_MESSAGE, null, null, null); } public static void aMethod (Action action) { for (int i=0;i<100;i++) { action.putValue("progress", i); action.actionPerformed(null); try { Thread.sleep(300); } catch (InterruptedException e) { e.printStackTrace(); } } } } It works but i know it lacks something. Any thoughts?

  Read the article

• FASM vc MASM trasnlation problem in mov si, offset msg

  - by Ruben Trancoso

  hi folks, just did my first test with MASM and FASM with the same code (almos) and I falled in trouble. The only difference is that to produce just the 104 bytes I need to write to MBR in FASM I put org 7c00h and in MASM 0h. The problem is on the mov si, offset msg that in the first case transletes it to 44 7C (7c44h) and with masm translates to 44 00 (0044h)! but just when I change org 7c00h to org 0h in MASM. Otherwise it will produce the entire segment from 0 to 7dff. how do I solve it? or in short, how to make MASM produce a binary that begins at 7c00h as it first byte and subsequent jumps remain relative to 7c00h? .model TINY .code org 7c00h ; Boot entry point. Address 07c0:0000 on the computer memory xor ax, ax ; Zero out ax mov ds, ax ; Set data segment to base of RAM jmp start ; Jump to the first byte after DOS boot record data ; ---------------------------------------------------------------------- ; DOS boot record data ; ---------------------------------------------------------------------- brINT13Flag db 90h ; 0002h - 0EH for INT13 AH=42 READ brOEM db 'MSDOS5.0' ; 0003h - OEM name & DOS version (8 chars) brBPS dw 512 ; 000Bh - Bytes/sector brSPC db 1 ; 000Dh - Sectors/cluster brResCount dw 1 ; 000Eh - Reserved (boot) sectors brFATs db 2 ; 0010h - FAT copies brRootEntries dw 0E0h ; 0011h - Root directory entries brSectorCount dw 2880 ; 0013h - Sectors in volume, < 32MB brMedia db 240 ; 0015h - Media descriptor brSPF dw 9 ; 0016h - Sectors per FAT brSPH dw 18 ; 0018h - Sectors per track brHPC dw 2 ; 001Ah - Number of Heads brHidden dd 0 ; 001Ch - Hidden sectors brSectors dd 0 ; 0020h - Total number of sectors db 0 ; 0024h - Physical drive no. db 0 ; 0025h - Reserved (FAT32) db 29h ; 0026h - Extended boot record sig brSerialNum dd 404418EAh ; 0027h - Volume serial number (random) brLabel db 'OSAdventure' ; 002Bh - Volume label (11 chars) brFSID db 'FAT12 ' ; 0036h - File System ID (8 chars) ;------------------------------------------------------------------------ ; Boot code ; ---------------------------------------------------------------------- start: mov si, offset msg call showmsg hang: jmp hang msg db 'Loading...',0 showmsg: lodsb cmp al, 0 jz showmsgd push si mov bx, 0007 mov ah, 0eh int 10h pop si jmp showmsg showmsgd: retn ; ---------------------------------------------------------------------- ; Boot record signature ; ---------------------------------------------------------------------- dw 0AA55h ; Boot record signature END

  Read the article

• Getting problem in Java OpenCV code.

  - by Chetan

  I had successfully compile my java code in Eclipse with name FaceDetection.java... I am getting an Exception in thread "main" java.lang.NoSuchMethodError: main.... Please help me to remove this Exception.. Here is the code import java.awt.; import java.awt.event.; import java.awt.image.MemoryImageSource; import hypermedia.video.OpenCV; @SuppressWarnings("serial") public class FaceDetection extends Frame implements Runnable { /** * Main method. * @param String[] a list of user's arguments passed from the console to this program */ public static void main( String[] args ) { System.out.println( "\nOpenCV face detection sample\n" ); new FaceDetection(); } // program execution frame rate (millisecond) final int FRAME_RATE = 1000/30; OpenCV cv = null; // OpenCV Object Thread t = null; // the sample thread // the input video stream image Image frame = null; // list of all face detected area Rectangle[] squares = new Rectangle[0]; /** * Setup Frame and Object(s). */ FaceDetection() { super( "Face Detection Sample" ); // OpenCV setup cv = new OpenCV(); cv.capture( 320, 240 ); cv.cascade( OpenCV.CASCADE_FRONTALFACE_ALT ); // frame setup this.setBounds( 100, 100, cv.width, cv.height ); this.setBackground( Color.BLACK ); this.setVisible( true ); this.addKeyListener( new KeyAdapter() { public void keyReleased( KeyEvent e ) { if ( e.getKeyCode()==KeyEvent.VK_ESCAPE ) { // ESC : release OpenCV resources cv.dispose(); System.exit(0); } } } ); // start running program t = new Thread( this ); t.start(); } /** * Draw video frame and each detected faces area. */ public void paint( Graphics g ) { // draw image g.drawImage( frame, 0, 0, null ); // draw squares g.setColor( Color.RED ); for( Rectangle rect : squares ) g.drawRect( rect.x, rect.y, rect.width, rect.height ); } /** * Execute this sample. */ @SuppressWarnings("static-access") public void run() { while( t!=null && cv!=null ) { try { t.sleep( FRAME_RATE ); // grab image from video stream cv.read(); // create a new image from cv pixels data MemoryImageSource mis = new MemoryImageSource( cv.width, cv.height, cv.pixels(), 0, cv.width ); frame = createImage( mis ); // detect faces squares = cv.detect( 1.2f, 2, OpenCV.HAAR_DO_CANNY_PRUNING, 20, 20 ); // of course, repaint repaint(); } catch( InterruptedException e ) {;} } } }

  Read the article

• Understanding VS2010 C# parallel profiling results

  - by Haggai

  I have a program with many independent computations so I decided to parallelize it. I use Parallel.For/Each. The results were okay for a dual-core machine - CPU utilization of about 80%-90% most of the time. However, with a dual Xeon machine (i.e. 8 cores) I get only about 30%-40% CPU utilization, although the program spends quite a lot of time (sometimes more than 10 seconds) on the parallel sections, and I see it employs about 20-30 more threads in those sections compared to serial sections. Each thread takes more than 1 second to complete, so I see no reason for them to work in parallel - unless there is a synchronization problem. I used the built-in profiler of VS2010, and the results are strange. Even though I use locks only in one place, the profiler reports that about 85% of the program's time is spent on synchronization (also 5-7% sleep, 5-7% execution, under 1% IO). The locked code is only a cache (a dictionary) get/add: bool esn_found; lock (lock_load_esn) esn_found = cache.TryGetValue(st, out esn); if(!esn_found) { esn = pData.esa_inv_idx.esa[term_idx]; esn.populate(pData.esa_inv_idx.datafile); lock (lock_load_esn) { if (!cache.ContainsKey(st)) cache.Add(st, esn); } } lock_load_esn is a static member of the class of type Object. esn.populate reads from a file using a separate StreamReader for each thread. However, when I press the Synchronization button to see what causes the most delay, I see that the profiler reports lines which are function entrance lines, and doesn't report the locked sections themselves. It doesn't even report the function that contains the above code (reminder - the only lock in the program) as part of the blocking profile with noise level 2%. With noise level at 0% it reports all the functions of the program, which I don't understand why they count as blocking synchronizations. So my question is - what is going on here? How can it be that 85% of the time is spent on synchronization? How do I find out what really is the problem with the parallel sections of my program? Thanks.

  Read the article

• Why is it still so hard to write software?

  - by nornagon

  Writing software, I find, is composed of two parts: the Idea, and the Implementation. The Idea is about thinking: "I have this problem; how do I solve it?" and further, "how do I solve it elegantly?" The answers to these questions are obtainable by thinking about algorithms and architecture. The ideas come partially through analysis and partially through insight and intuition. The Idea is usually the easy part. You talk to your friends and co-workers and you nut it out in a meeting or over coffee. It takes an hour or two, plus revisions as you implement and find new problems. The Implementation phase of software development is so difficult that we joke about it. "Oh," we say, "the rest is a Simple Matter of Code." Because it should be simple, but it never is. We used to write our code on punch cards, and that was hard: mistakes were very difficult to spot, so we had to spend extra effort making sure every line was perfect. Then we had serial terminals: we could see all our code at once, search through it, organise it hierarchically and create things abstracted from raw machine code. First we had assemblers, one level up from machine code. Mnemonics freed us from remembering the machine code. Then we had compilers, which freed us from remembering the instructions. We had virtual machines, which let us step away from machine-specific details. And now we have advanced tools like Eclipse and Xcode that perform analysis on our code to help us write code faster and avoid common pitfalls. But writing code is still hard. Writing code is about understanding large, complex systems, and tools we have today simply don't go very far to help us with that. When I click "find all references" in Eclipse, I get a list of them at the bottom of the window. I click on one, and I'm torn away from what I was looking at, forced to context switch. Java architecture is usually several levels deep, so I have to switch and switch and switch until I find what I'm really looking for -- by which time I've forgotten where I came from. And I do that all day until I've understood a system. It's taxing mentally, and Eclipse doesn't do much that couldn't be done in 1985 with grep, except eat hundreds of megs of RAM. Writing code has barely changed since we were staring at amber on black. We have the theoretical groundwork for much more advanced tools, tools that actually work to help us comprehend and extend the complex systems we work with every day. So why is writing code still so hard?

  Read the article

• What are the types and inner workings of a query optimizer?

  - by Frank Developer

  As I understand it, most query optimizers are cost-based. Some can be influenced by hints like FIRST_ROWS(). Others are tailored for OLAP. Is it possible to know more detailed logic about how Informix IDS and SE's optimizers decide what's the best route for processing a query, other than SET EXPLAIN? Is there any documentation which illustrates the ranking of SELECT statements? I would imagine that "SELECT col FROM table WHERE ROWID = n" ranks 1st. What are the rest of them?.. If I'm not mistaking, Informix's ROWID is a SERIAL(INT) which allows for a max. of 2GB nrows, or maybe it uses INT9 for TB's nrows?.. However, I think Oracle uses HEX values for ROWID. Too bad ROWID can't be oftenly used, since a rows ROWID can change. So maybe ROWID is used by the optimizer as a counter? Perhaps, it could be used for implementing the query progress idea I mentioned in my "Begin viewing query results before query completes" question? For some reason, I feel it wouldn't be that difficult to report a query's progress while being processed, perhaps at the expense of some slight overhead, but it would be nice to know ahead of time: A "Google-like" estimate of how many rows meet a query's criteria, display it's progress every 100, 200, 500 or 1,000 rows, give users the ability to cancel it at anytime and start displaying the qualifying rows as they are being put into the current list, while it continues searching?.. This is just one example, perhaps we could think other neat/useful features, the ingridients are more or less there. Perhaps we could fine-tune each query with more granularity than currently available? OLTP queries tend to be mostly static and pre-defined. The "what-if's" are more OLAP, so let's try to add more control and intelligence to it? So, therefore, being able to more precisely control, not "hint-influence" a query is what's needed and therefore it would be necessary to know how the optimizers logic is programmed. We can then have Dynamic SELECT and other statements for specific situations! Maybe even tell IDS to read blocks of indexes nodes at-a-time instead of one-by-one, etc. etc.

  Read the article

• Middleware with generic communication media layer

  - by Tom

  Greetings all, I'm trying to implement middleware (driver) for an embedded device with generic communication media layer. Not sure what is the best way to do it so I'm seeking an advice from more experienced stackoverflow users:). Basically we've got devices around the country communicating with our servers (or a pda/laptop in used in field). Usual form of communication is over TCP/IP, but could be also using usb, RF dongle, IR, etc. The plan is to have object corresponding with each of these devices, handling the proprietary protocol on one side and requests/responses from other internal systems on the other. The thing is how create something generic in between the media and the handling objects. I had a play around with the TCP dispatcher using boost.asio but trying to create something generic seems like a nightmare :). Anybody tried to do something like that? What is the best way how to do it? Example: Device connects to our Linux server. New middleware instance is created (on the server) which announces itself to one of the running services (details are not important). The service is responsible for making sure that device's time is synchronized. So it asks the middleware what is the device's time, driver translates it to device language (protocol) and sends the message, device responses and driver again translates it for the service. This might seem as a bit overkill for such a simple request but imagine there are more complex requests which the driver must translate, also there are several versions of the device which use different protocol, etc. but would use the same time sync service. The goal is to abstract the devices through the drivers to be able to use the same service to communicate with them. Another example: we find out that the remote communications with the device are down. So we send somebody out with PDA, he connects to the device using USB cable. Starts up the application which has the same functionality as the timesync service. Again middleware instance is created (on the PDA) to translate communication between application and the device this time only using USB/serial media not TCP/IP as in previous example. I hope it makes more sense now :) Cheers, Tom

  Read the article

• No exception, no error, still i dont recieve the json object from my http post

  - by user2978538

  My source code: final Thread t = new Thread() { public void run() { Looper.prepare(); HttpClient client = new DefaultHttpClient(); HttpConnectionParams.setConnectionTimeout(client.getParams(), 10000); HttpResponse response; JSONObject obj = new JSONObject(); try { HttpPost post = new HttpPost("http://pc.dyndns-office.com/mobile.asp"); obj.put("Model", ReadIn1); obj.put("Product", ReadIn2); obj.put("Manufacturer", ReadIn3); obj.put("RELEASE", ReadIn4); obj.put("SERIAL", ReadIn5); obj.put("ID", ReadIn6); obj.put("ANDROID_ID", ReadIn7); obj.put("Language", ReadIn8); obj.put("BOARD", ReadIn9); obj.put("BOOTLOADER", ReadIn10); obj.put("BRAND", ReadIn11); obj.put("CPU_API", ReadIn12); obj.put("DISPLAY", ReadIn13); obj.put("FINGERPRINT", ReadIn14); obj.put("HARDWARE", ReadIn15); obj.put("UUID", ReadIn16); StringEntity se = new StringEntity(obj.toString()); se.setContentType(new BasicHeader(HTTP.CONTENT_TYPE, "application/json")); post.setEntity(se); post.setHeader("host", "http://pc.dyndns-office.com/mobile.asp"); response = client.execute(post); if (response != null) { InputStream in = response.getEntity().getContent(); } } catch (Exception e) { e.printStackTrace(); } Looper.loop(); } }; t.start(); } } i want to send an Json object to a Website. As far as I can see, I set the header, but still I get this exception, can someone help me? (I'm using Android-Studio) __ Edit: i don't get any exceptions anymore, but still i do not receive the json packet. When i manually call the website i get a log file entry. Does anyone know, what's wrong? Edit2: When i debug i get as response "HTTP/1.1 400 bad request" i'm sure its not an permission problem. Any ideas?

  Read the article

• Writing Device Drivers for Microcontrollers, where to define IO Port pins?

  - by volting

  I always seem to encounter this dilemma when writing low level code for MCU's. I never know where to declare pin definitions so as to make the code as reusable as possible. In this case Im writing a driver to interface an 8051 to a MCP4922 12bit serial DAC. Im unsure how/where I should declare the pin definitions for The CS(chip select) and LDAC(data latch) for the DAC. At the moment there declared in the header file for the driver. Iv done a lot of research trying to figure out the best approach but havent really found anything. Im basically want to know what the best practices... if there are some books worth reading or online information, examples etc, any recommendations would be welcome. Just a snippet of the driver so you get the idea /** @brief This function is used to write a 16bit data word to DAC B -12 data bit plus 4 configuration bits @param dac_data A 12bit word @param ip_buf_unbuf_select Input Buffered/unbuffered select bit. Buffered = 1; Unbuffered = 0 @param gain_select Output Gain Selection bit. 1 = 1x (VOUT = VREF * D/4096). 0 =2x (VOUT = 2 * VREF * D/4096) */ void MCP4922_DAC_B_TX_word(unsigned short int dac_data, bit ip_buf_unbuf_select, bit gain_select) { unsigned char low_byte=0, high_byte=0; CS = 0; /**Select the chip*/ high_byte |= ((0x01 << 7) | (0x01 << 4)); /**Set bit to select DAC A and Set SHDN bit high for DAC A active operation*/ if(ip_buf_unbuf_select) high_byte |= (0x01 << 6); if(gain_select) high_byte |= (0x01 << 5); high_byte |= ((dac_data >> 8) & 0x0F); low_byte |= dac_data; SPI_master_byte(high_byte); SPI_master_byte(low_byte); CS = 1; LDAC = 0; /**Latch the Data*/ LDAC = 1; }

  Read the article

• Parallel Task Library WaitAny Design

  - by colithium

  I've just begun to explore the PTL and have a design question. My Scenario: I have a list of URLs that each refer to an image. I want each image to be downloaded in parallel. As soon as at least one image is downloaded, I want to execute a method that does something with the downloaded image. That method should NOT be parallelized -- it should be serial. I think the following will work but I'm not sure if this is the right way to do it. Because I have separate classes for collecting the images and for doing "something" with the collected images, I end up passing around an array of Tasks which seems wrong since it exposes the inner workings of how images are retrieved. But I don't know a way around it. In reality there is more to both of these methods but that's not important for this. Just know that they really shouldn't be lumped into one large method that both retrieves and does something with the image. Task<Image>[] downloadTasks = collector.RetrieveImages(listOfURLs); for (int i = 0; i < listOfURLs.Count; i++) { //Wait for any of the remaining downloads to complete int completedIndex = Task<Image>.WaitAny(downloadTasks); Image completedImage = downloadTasks[completedIndex].Result; //Now do something with the image (this "something" must happen serially) } /////////////////////////////////////////////////// public Task<Image>[] RetrieveImages(List<string> urls) { Task<Image>[] tasks = new Task<Image>[urls.Count]; int index = 0; foreach (string url in urls) { string lambdaVar = url; //Required... Bleh tasks[index] = Task<Image>.Factory.StartNew(() => { using (WebClient client = new WebClient()) { //TODO: Replace with live image locations string fileName = String.Format("{0}.png", i); client.DownloadFile(lambdaVar, Path.Combine(Application.StartupPath, fileName)); } return Image.FromFile(Path.Combine(Application.StartupPath, fileName)); }, TaskCreationOptions.LongRunning | TaskCreationOptions.AttachedToParent); index++; } return tasks; }

  Read the article

• Strange compilation error - GAS3 generated class

  - by subh

  I am pretty new to GraniteDS..So far I have been able to successfully configure it to work with my remote java services as well as generate the equivalent AS3 files from my POJO's. But I am getting this strange error while building one of the classes using GAS3 [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[77,29] Syntax error: expecting identifier before use. public function set use(value:String):void { [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[77,52] Syntax error: expecting leftparen before leftbrace. public function set use(value:String):void { [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[77,52] Syntax error: expecting identifier before leftbrace. public function set use(value:String):void { [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[77,52] Syntax error: expecting rightparen before leftbrace. public function set use(value:String):void { [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[80,29] Syntax error: expecting identifier before use. public function get use():String { [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[80,42] Syntax error: expecting leftparen before leftbrace. public function get use():String { [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[80,42] Syntax error: expecting identifier before leftbrace. public function get use():String { [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[80,42] Syntax error: expecting rightparen before leftbrace. public function get use():String { The java class appears like this @Entity` @Table(name = "mmd_tank_grades_ml") @SuppressWarnings("serial") public class TankGradesMl implements Serializable { .... private String use; @Basic @Column(name = "USE", length = 45) public String getUse() { return use; } public void setUse(String use) { this.use = use; } What am I doing wrong? How to resolve this error? I tried by changing the java source variable like below private String usedFor; ---- @Basic @Column(name = "USE", length = 45) public String getUsedFor() { return usedFor; } /** * @param use * new value for use */ public void setUsedFor(String usedFor) { this.usedFor = usedFor; } and the error is gone...not sure why it was throwing exception for 'use'..too small for variable name :-)

  Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >