Search Results

Search found 1696 results on 68 pages for 'ten ton gorilla'.

Page 59/68 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

• 3Ware 9650SE RAID-6, two degraded drives, one ECC, rebuild stuck

  - by cswingle

  This morning I came in the office to discover that two of the drives on a RAID-6, 3ware 9650SE controller were marked as degraded and it was rebuilding the array. After getting to about 4%, it got ECC errors on a third drive (this may have happened when I attempted to access the filesystem on this RAID and got I/O errors from the controller). Now I'm in this state: > /c2/u1 show Unit UnitType Status %RCmpl %V/I/M Port Stripe Size(GB) ------------------------------------------------------------------------ u1 RAID-6 REBUILDING 4%(A) - - 64K 7450.5 u1-0 DISK OK - - p5 - 931.312 u1-1 DISK OK - - p2 - 931.312 u1-2 DISK OK - - p1 - 931.312 u1-3 DISK OK - - p4 - 931.312 u1-4 DISK OK - - p11 - 931.312 u1-5 DISK DEGRADED - - p6 - 931.312 u1-6 DISK OK - - p7 - 931.312 u1-7 DISK DEGRADED - - p3 - 931.312 u1-8 DISK WARNING - - p9 - 931.312 u1-9 DISK OK - - p10 - 931.312 u1/v0 Volume - - - - - 7450.5 Examining the SMART data on the three drives in question, the two that are DEGRADED are in good shape (PASSED without any Current_Pending_Sector or Offline_Uncorrectable errors), but the drive listed as WARNING has 24 uncorrectable sectors. And, the "rebuild" has been stuck at 4% for ten hours now. So: How do I get it to start actually rebuilding? This particular controller doesn't appear to support /c2/u1 resume rebuild, and the only rebuild command that appears to be an option is one that wants to know what disk to add (/c2/u1 start rebuild disk=<p:-p...> [ignoreECC] according to the help). I have two hot spares in the server, and I'm happy to engage them, but I don't understand what it would do with that information in the current state it's in. Can I pull out the drive that is demonstrably failing (the WARNING drive), when I have two DEGRADED drives in a RAID-6? It seems to me that the best scenario would be for me to pull the WARNING drive and tell it to use one of my hot spares in the rebuild. But won't I kill the thing by pulling a "good" drive in a RAID-6 with two DEGRADED drives? Finally, I've seen reference in other posts to a bad bug in this controller that causes good drives to be marked as bad and that upgrading the firmware may help. Is flashing the firmware a risky operation given the situation? Is it likely to help or hurt wrt the rebuilding-but-stuck-at-4% RAID? Am I experiencing this bug in action? Advice outside the spiritual would be much appreciated. Thanks.

  Read the article

• Windows 7 laptop constantly dropping internet connection

  - by Corbin Holbert

  I have scoured the web for an answer and failed to find one. I am using a Toshiba Satellite laptop running Windows 7 64-Bit. I have the computer connected via Wifi. Now, I am no beginner with the Internet, or anything related to computers, as I have grown up teaching everyone around me how to use computers, and went to college for IT. Everything on my network works flawlessly at all times, except for this evil laptop. The worst part is that I fixed this once before a few years back and recently had to replace the hard drive and re-install the OS, but cannot for the life of me remember what I did to make this problem go away. I am in my browser, connected to the Internet. I click a link. Suddenly no internet access. All I do is click down on the WiFi connection in the task bar, disconnect and reconnect immediately. Internet is back the moment I hit "connect." I have read many people had the same issues as I am having, but they all had triggers or other network issues. I have no trigger (this happens literally five to six times per minute no matter what I am doing) and I have no problems with my router, modem, or any other devices or computers on said network. As I am a web designer, and like to test my work live at every turn- this is going to result in this laptop being in pieces if I can't get it fixed soon. If more info is needed, let me know and I will provide. Thanks for any help offered! EDIT: Network Card: Realtek RTL8188CE Wireless LAN 802.11n PCI-E NIC Network state reads as "No Internet Access" when the problem first occurs, then magically I have Internet access for about ten seconds once I disconnect and reconnect. I have turned off IPV6, I have turned off power saving options for the network adapter, no viruses. Any new ideas? Also, I had to disconnect and reconnect four times just to get to this edit screen- and will likely have to do the same just to post it- it's that bad.

  Read the article

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  Hello, I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• Amusing or Sad? Network Solutions

  - by dbasnett

  When I got sick my email ended up in every drug sellers email list. Some days I get over 200 emails selling everything from Viagra to Xanax. Either they don't know what my condition is or they are telling me you are a goner, might as well chill-ax and have a good time. In order to cut down on the mail being downloaded I thought I would add all of the Junk email senders from Outlook to my Network Solution mail server. Much to my amazement I could not find that import Spammers button, so I submitted a tech support request. Here is the response: Thank you for contacting Network Solutions Customer Service Department. We are committed to creating the best Customer experience possible. One of the first ways we can demonstrate our commitment to this goal is to quickly and efficiently handle your recent request. We apologize for any inconvenience this might have caused you. With regard to your concern, please be advised that we cannot import blocked senders in to you e-mail servers. An alternative option is for you to create a Custom Filter that filters unwanted e-mails. To create a Custom Filter: Open a Web browser (e.g., Netscape, Microsoft Internet Explorer, etc.). Type mail.[domain name].[ext] in the address line. Login to your Network Solutions email account. Click on the Configuration left menu tab. Click on the Custom Filter link. Type the rule name. blah, blah, blah Basically add them one at a time. "We are committed to creating the best Customer experience possible." No you are not. You are trying to squeeze every nickle you can out of me. "With regard to your concern, please be advised that we cannot import blocked senders in to you e-mail servers." Maybe I should apply for a job to write those ten complicated lines of code... Maybe I should question my choice of vendors, because if they truly "cannot" then they are to stupid to have my business. It is both amusing and sad. I'll be posting this in every forum I am a member of.

  Read the article

• Wifi randomly drops on Windows 8 laptop

  - by JosiahS

  First of all, I did a lot of research on this problem, and I wasn't able to come to any helpful conclusion. I've finally decided that I need advice from those who might know where to look. So don't let me down. :P I used to have an older Windows 7 laptop, which worked great for basic office and web browsing. However, I wanted something that would play actual modern games. So I recently bought a Sager NP8235 with the Intel Wireless-AC 7260 wifi card, and installed Windows 8 Pro on it. And ever since, I've been having problems with the wifi. Generally, what happens is if I leave the laptop on but inactive for an extended amount of time (I've estimated it around an hour to two), the wifi will start dropping randomly. If I happened to have a download going at the time, it usually causes the download to fail. Or, if I put the laptop to sleep overnight, the next morning I usually have to restart the computer because the wifi device apparently stops working (it literally won't turn on). Also, and most frustrating, whenever I'm on a video chat (like Skype), after about ten minutes, the connection will start lagging like crazy, until it forces Skype to end the call. After that, I usually have to disable and reenable the wifi to get it working again. I know it isn't our internet, because all the other computers in our house (~8) don't have any issues. Even the old Windows 7 laptop (connected also over wifi) works just fine, scoring the normal ~3Mbps average on speedtest.net (yes, I know our internet is slow, we live out in the country). Additionally, when I connect the Sager directly to the router via ethernet, the internet instantly starts working just great. Like I said, I've done a lot of googling to figure out what's going on, and I haven't been able to find anything that worked for me. Is it Windows 8 conflicting with the Wifi drivers? As of this writing, I have the Intel drivers v16.1.5.2 installed (without the extra Intel software). Or is it our router? It's a TP-Link TL-WR841ND, set to the default settings. The Sager is currently being assigned to a static IP, if that makes any difference. And yet, the old windows 7 laptop has a much more stable connection than the Sager. Anyone have any ideas? At this point, I'd appreciate even knowing what the problem is.

  Read the article

• Why does Excel now give me already existing name range error on Copy Sheet?

  - by WilliamKF

  I've been working on a Microsoft Excel 2007 spreadsheet for several days. I'm working from a master template like sheet and copying it to a new sheet repeatedly. Up until today, this was happening with no issues. However, in the middle of today this suddenly changed and I do not know why. Now, whenever I try to copy a worksheet I get about ten dialogs, each one with a different name range object (shown below as 'XXXX') and I click yes for each one: A formula or sheet you want to move or copy contains the name 'XXXX', which already exists on the destination worksheet. Do you want to use this version of the name? To use the name as defined in destination sheet, click Yes. To rename the range referred to in the formula or worksheet, click No, and enter a new name in the Name Conflict dialog box. The name range objects refer to cells in the sheet. For example, E6 is called name range PRE on multiple sheets (and has been all along) and some of the formulas refer to PRE instead of $E$6. One of the 'XXXX' above is this PRE. These name ranges should only be resolved within the sheet within which they appear. This was not an issue before despite the same name range existing on multiple sheets before. I want to keep my name ranges. What could have changed in my spreadsheet to cause this change in behavior? I've gone back to prior sheets created this way and now they give the message too when copied. I tried a different computer and a different user and the same behavior is seen everywhere. I can only conclude something in the spreadsheet has changed. What could this be and how can I get back the old behavior whereby I can copy sheets with name ranges and not get any errors? Looking in the Name Manager I see that the name ranges being complained about show twice, once as scope Template and again as scope Workbook. If I delete the scope Template ones the error goes away on copy however, I get a bunch of #REF errors. If I delete the scope Workbook ones, all seems okay and the errors on copy go away too, so perhaps this is the answer, but I'm nervous about what effect this deletion will have and wonder how the Workbook ones came into existence in the first place. Will it be safe to just delete the Workbook name manager scoped entries and how might these have come into existence without my knowing it to begin with?

  Read the article

• TFS and shared projects in multiple solutions

  - by David Stratton

  Our .NET team works on projects for our company that fall into distinct categories. Some are internal web apps, some are external (publicly facing) web apps, we also have internal Windows applications for our corporate office users, and Windows Forms apps for our retail locations (stores). Of course, because we hate code reuse, we have a ton of code that is shared among the different applications. Currently we're using SVN as our source control, and we've got our repository laid out like this: - = folder, | = Visual Studio Solution -SVN - Internet | Ourcompany.com | Oursecondcompany.com - Intranet | UniformOrdering website | MessageCenter website - Shared | ErrorLoggingModule | RegularExpressionGenerator | Anti-Xss | OrgChartModule etc... So.. The OurCompany.com solution in the Internet folder would have a website project, and it would also include the ErrorLoggingModule, RegularExpressionGenerator, and Anti-Xss projects from the shared directory. Similarly, our UniformOrdering website solution would have each of these projects included in the solution as well. We prefer to have a project reference to a .dll reference because, first of all, if we need to add or fix a function in the ErrorLoggingModule while working on the OurCompany.com website, it's right there. Also, this allows us to build each solution and see if changes to shared code break any other applications. This should work well on a build server as well if I'm correct. In SVN, there is no problem with this. SVN and Visual Studio aren't tied together in the way TFS's source control is. We never figured out how to work this type of structure in TFS when we were using it, because in TFS, the TFS project was always tied to a Visual Studio Solution. The Source Code repository was a child of the TFS Project, so if we wanted to do this, we had to duplicate the Shared code in each TFS project's source code repository. As my co-worker put it, this "breaks every known best practice about code reuse and simplicity". It was enough of a deal breaker for us that we switched to SVN. Now, however, we're faced with truly fixing our development processes, and the Application Lifecycle Management of TFS is pretty close to exactly what we want, and how we want to work. Our one sticking point is the shared code issue. We're evaluating other commercial and open source solutions, but since we're already paying for TFS with our MSDN Subscriptions, and TFS is pretty much exactly what we want, we'd REALLY like to find a way around this issue. Has anybody else faced this and come up with a solution? If you've seen an article or posting on this that you can share with me, that would help as well. As always, I'm open to answers like "You're looking at it all wrong, bonehead, HERE'S the way it SHOULD be done.

  Read the article

• Bugs in Excel's ActiveX combo boxes?

  - by k.robinson

  I have noticed that I get all sorts of annoying errors when: I have ActiveX comboboxes on a worksheet (not an excel form) The comboboxes have event code linked to them (eg, onchange events) I use their listfillrange or linkedcell properties (clearing these properties seems to alleviate a lot of problems) (Not sure if this is connected) but there is data validation on the targeted linkedcell. I program a fairly complex excel application that does a ton of event handling and uses a lot of controls. Over the months, I have been trying to deal with a variety of bugs dealing with those combo boxes. I can't recall all the details of each instance now, but these bugs tend to involve pointing the listfillrange and linkedcell properties at named ranges, and often have to do with the combo box events triggering at inappropriate times (such as when application.enableevents = false). These problems seemed to grow bigger in Excel 2007, so that I had to give up on these combo boxes entirely (I now use combo boxes contained in user forms, rather than directly on the sheets). Has anyone else seen similar problems? If so, was there a graceful solution? I have looked around with Google and so far haven't spotted anyone with similar issues. Some of the symptoms I end up seeing are: Excel crashing when I start up (involves combobox_onchange, listfillrange-named range on another different sheet, and workbook_open interactions). (note, I also had some data validation on the the linked cells in case a user edited them directly.) Excel rendering bugs (usually when the combo box changes, some cells from another sheet get randomly drawn over the top of the current sheet) Sometimes it involves the screen flashing entirely to another sheet for a moment. Excel losing its mind (or rather, the call stack) (related to the first bullet point). Sometimes when a function modifies a property of the comboboxes, the combobox onchange event fires, but it never returns control to the function that caused the change in the first place. The combobox_onchange events are triggered even when application.enableevents = false. Events firing when they shouldn't (I posted another question on stack overflow related to this). At this point, I am fairly convinced that ActiveX comboboxes are evil incarnate and not worth the trouble. I have switched to including these comboboxes inside a userform module instead. I would rather inconvenience users with popup forms than random visual artifacts and crashing (with data loss).

  Read the article

• Best programming aids for a quadriplegic programmer

  - by Peter Rowell

  Before you jump to conclusions, yes, this is programming related. It covers a situation that comes under the heading of, "There, but for the grace of God, go you or I." This is brand new territory for me so I'm asking for some serious help here. A young man, Honza Ripa, in a nearby town did the classic Dumb Thing two weeks after graduating from High School -- he dove into shallow water in the Russian River and had a C-4/C-5 break, sometimes called a Swimming Pool break. In a matter of seconds he went from an exceptional golfer and wrestler to a quadriplegic. (Read the story ... all of us should have been so lucky as to have a girlfriend like Brianna.) That was 10 months ago and he has regained only tiny amounts of control of his right index finger and a couple of other hand/foot motions, none of them fine-grained. His total control of his computer (currently running Win7, but we can change that as needed) is via voice command. Honza's not dumb. He had a 3.7 GPA with AP math and physics. The Problems: Since all of his input is via voice command, he is concerned that the predominance of special characters in programming will require vast amount of verbose commands. Does anyone know of any well done voice input system specifically designed for programmers? I'm thinking about something that might be modal--e.g. you say "Python input" and it goes into a macro mode for doing class definitions, etc. Given all of the RSI in programmer-land there's got to be something out there. What OS(es) does it run on? I am planning on teaching him Python, which is my preferred language for programming and teaching. Are there any applications / whatevers that are written in Python and would be a particularly good match for engaging him mentally while supporting his disability? One of his expressed interests is in stock investing, but that not might be a good starting point for a brand-new programmer. There are a lot of environments (Flash, JavaScript, etc) that are not particularly friendly to people with accessibility challenges. I vaguely remember (but cannot find) a research project that basically created an overlay system on top of a screen environment and then allowed macro command construction on top of the screen image. If we can get/train this system, we may be able to remove many hurdles to using the net. I am particularly interested in finding open source Python-based robotics and robotic prostheses projects so that he can simultaneously learn advanced programming concepts while learning to solve some of his own immediate problems. I've done a ton of googling on this, but I know there things I'm missing. I'm asking the SO community to step up to the plate here. I know this group has the answers, so let me hear them! Overwhelm me with the opportunities that any of us might have/need to still program after such a life-changing event.

  Read the article

• How much abstraction is too much?

  - by Daniel Bingham

  In an Object Oriented Program: How much abstraction is too much? How much is just right? I have always been a nuts and bolts kind of guy. I understood the concept behind high levels of encapsulation and abstraction, but always felt instinctively that adding too much would just confuse the program. I always tried to shoot for an amount of abstraction that left no empty classes or layers. And where in doubt, instead of adding a new layer to the hierarchy, I would try and fit something into the existing layers. However, recently I've been encountering more highly abstracted systems. Systems where everything that could require a representation later in the hierarchy gets one up front. This leads to a lot of empty layers, which at first seems like bad design. However, on second thought I've come to realize that leaving those empty layers gives you more places to hook into in the future with out much refactoring. It leaves you greater ability to add new functionality on top of the old with out doing nearly as much work to adjust the old. The two risks of this seem to be that you could get the layers you need wrong. In this case one would wind up still needing to do substantial refactoring to extend the code and would still have a ton of never used layers. But depending on how much time you spend coming up with the initial abstractions, the chance of screwing it up, and the time that could be saved later if you get it right - it may still be worth it to try. The other risk I can think of is the risk of over doing it and never needing all the extra layers. But is that really so bad? Are extra class layers really so expensive that it is much of a loss if they are never used? The biggest expense and loss here would be time that is lost up front coming up with the layers. But much of that time still might be saved later when one can work with the abstracted code rather than more low level code. So when is it too much? At what point do the empty layers and extra "might need" abstractions become overkill? How little is too little? Where's the sweet spot? Are there any dependable rules of thumb you've found in the course of your career that help you judge the amount of abstraction needed?

  Read the article

• Page expired issue with back button and wicket SortableDataProvider and DataTable

  - by David

  Hi, I've got an issue with SortableDataProvider and DataTable in wicket. I've defined my DataTable as such: IColumn<Column>[] columns = new IColumn[9]; //column values are mapped to the private attributes listed in ColumnImpl.java columns[0] = new PropertyColumn(new Model("#"), "columnPosition", "columnPosition"); columns[1] = new PropertyColumn(new Model("Description"), "description"); columns[2] = new PropertyColumn(new Model("Type"), "dataType", "dataType"); Adding it to the table: DataTable<Column> dataTable = new DataTable<Column>("columnsTable", columns, provider, maxRowsPerPage) { @Override protected Item<Column> newRowItem(String id, int index, IModel<Column> model) { return new OddEvenItem<Column>(id, index, model); } }; My data provider: public class ColumnSortableDataProvider extends SortableDataProvider<Column> { private static final long serialVersionUID = 1L; private List list = null; public ColumnSortableDataProvider(Table table, String sortProperty) { this.list = Arrays.asList(table.getColumns().toArray(new Column[0])); setSort(sortProperty, true); } public ColumnSortableDataProvider(List list, String sortProperty) { this.list = list; setSort(sortProperty, true); } @Override public Iterator iterator(int first, int count) { /* first - first row of data count - minimum number of elements to retrieve So this method returns an iterator capable of iterating over {first, first+count} items */ Iterator iterator = null; try { if(getSort() != null) { Collections.sort(list, new Comparator() { private static final long serialVersionUID = 1L; @Override public int compare(Column c1, Column c2) { int result=1; PropertyModel<Comparable> model1= new PropertyModel<Comparable>(c1, getSort().getProperty()); PropertyModel<Comparable> model2= new PropertyModel<Comparable>(c2, getSort().getProperty()); if(model1.getObject() == null && model2.getObject() == null) result = 0; else if(model1.getObject() == null) result = 1; else if(model2.getObject() == null) result = -1; else result = ((Comparable)model1.getObject()).compareTo(model2.getObject()); result = getSort().isAscending() ? result : -result; return result; } }); } if (list.size() (first+count)) iterator = list.subList(first, first+count).iterator(); else iterator = list.iterator(); } catch (Exception e) { e.printStackTrace(); } return iterator; } The problem is the following: - I click a column header to sort by that column. - I navigate to a different page - I click Back (or Forward if I do the opposite scenario) - Page has expired. It'd be nice to generate the page using PageParameters but I somehow need to intercept the sort event to do so. Any pointers would be greatly appreciated. Thanks a ton!! David

  Read the article

• Use a subdirectory as root with htaccess in Apache 1.3

  - by Andrew

  I'm trying to deploy a site generated with Jekyll and would like to keep the site in its own subfolder on my server to keep everything more organized. Essentially, I'd like to use the contents of /jekyll as the root unless a file similarly named exists in the actual web root. So something like /jekyll/sample-page/ would show as http://www.example.com/sample-page/, while something like /other-folder/ would display as http://www.example.com/other-folder. My test server runs Apache 2.2 and the following .htaccess (adapted from http://gist.github.com/97822) works flawlessly: RewriteEngine On # Map http://www.example.com to /jekyll. RewriteRule ^$ /jekyll/ [L] # Map http://www.example.com/x to /jekyll/x unless there is a x in the web root. RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} !^/jekyll/ RewriteRule ^(.*)$ /jekyll/$1 # Add trailing slash to directories without them so DirectoryIndex works. # This does not expose the internal URL. RewriteCond %{REQUEST_FILENAME} -d RewriteCond %{REQUEST_FILENAME} !/$ RewriteRule ^(.*)$ $1/ # Disable auto-adding slashes to directories without them, since this happens # after mod_rewrite and exposes the rewritten internal URL, e.g. turning # http://www.example.com/about into http://www.example.com/jekyll/about. DirectorySlash off However, my production server runs Apache 1.3, which doesn't allow DirectorySlash. If I disable it, the server gives a 500 error because of internal redirect overload. If I comment out the last section of ReWriteConds and rules: RewriteCond %{REQUEST_FILENAME} -d RewriteCond %{REQUEST_FILENAME} !/$ RewriteRule ^(.*)$ $1/ …everything mostly works: http://www.example.com/sample-page/ displays the correct content. However, if I omit the trailing slash, the URL in the address bar exposes the real internal URL structure: http://www.example.com/jekyll/sample-page/ What is the best way to account for directory slashes in Apache 1.3, where useful tools like DirectorySlash don't exist? How can I use the /jekyll/ directory as the site root without revealing the actual URL structure? Edit: After a ton of research into Apache 1.3, I've found that this problem is essentially a combination of two different issues listed at the Apache 1.3 URL Rewriting Guide. I have a (partially) moved DocumentRoot, which in theory would be taken care of with something like this: RewriteRule ^/$ /e/www/ [R] I also have the infamous "Trailing Slash Problem," which is solved by setting the RewriteBase (as was suggested in one of the responses below): RewriteBase /~quux/ RewriteRule ^foo$ foo/ [R] The problem is combining the two. Moving the document root doesn't (can't?) use RewriteBase—fixing trailing slashes requires(?) it… Hmm…

  Read the article

• Is Zend Framework a total waste of my time?

  - by Citizen

  Ok, I'm about 50% done with the "30 minute" quickstart guide from Zend. I must be missing something, because this seems like a total waste of time. The point of this quickguide is to create a guestbook, something I could do in 5 minutes with regular naked non-framework php. Here's my path to zend framework: c:/program files/wamp/www/_zend/ Here's my path to my quickstart project: c:/program files/wamp/www/_zend/bin/quickstart/ I have a number of questions at this point: http://framework.zend.com/docs/quickstart/create-a-model-and-database-table 1: I'm running the command line to run my database loading script. I get an error stating the it can't find the Zend/AutoLoader.php becuase my path to the zend library is wrong. I followed all of the steps. I defined the path to my zend library in the main config file, but for some reason, its defined again in my db loader. In all of these scripts that they have me load, it points the relative path to the zend library as being /../library Problem is, there's nothing in that folder. To get to my actual zend folder, you'd need to be (relatively) /../../../../library Which brings me to my 2nd question: 2: Where the #$#$ is the main Zend files supposed to be? The install directions were basically "put it wherever you want", when the real answer (after a bunch of errors and wasted time was) was "put it somewhere so that its really easy to type the full path a thousand times in command line" and "it also better be in a runnable place on your webserver since its going to create your quickstart application in a subdirectory within zend". Which brings us to the third question 3: Am I supposed to have this libary in both the parent core Zend (wamp/_zend/library) AND my application (quickstart/library)? 4: If that is the case, it seems like a ton of wasted files to be uploading. I'd like to use Zend to create products that my customers will download. 5 megs of overhead seems like a bit much. Zend claims you can use these library components separately, but it looks to me like I'm going to have to upload them every time. Which leads to the next question: 5: It appears that perhaps Zend is more for a single application that is not supposed to be distributed. Is this not the case? 6: According to their default file structure everything but my /public folder would be above public_html on my server if I wanted this to rest on my TLD. I would need to rename every reference of /public/ to /public_html/, or am I missing something else?

  Read the article

• Git/Mercurial (hg) opinion

  - by Richard

  First, let me say I'm not a professional programmer, but an engineer who had a need for it and had to learn. I was always working alone, so it was just me and my seven splitted personalities ... and we worked okey as a team :) Most of my stuff is done in C/Fortran/Matlab and so far I've been learning git to manage it all. However, although I've had no unsolvable problems with it, I've never been "that" happy with it ... for everything I cannot do, I hae to look up a book. And, for some time now I've been hearning a lot of good stuff about hg. Now, a coleague of mine will have to work with me on a project (I almost feel sorry for him) and he's started learning hg (says he likes it more), and I'm considering the switch myself. We work almost exclusivly on Windows platform (although I manage relatively ok using unix tools and things that come from that part of the world). So, I was wondering, in a described scenario, what problems could I expect with the switch. I heard that hg is rather more user friendly towards windows users, regarding the user interfaces. How does it handle repositories ? Does it create them the same way as git does (just one subdirectory in a working directory) and can I just copy the whole project directory (including git repo) and just carry them somewhere with no extra thinking ? (I really liked that when I was choosing over git/svn). Are there any good books on it that you can recommend (something like Pro Git, only for Hg). What are good ways to implement hg into Visual Studio/GVim for Windows, or into Windows Explorer so I can work relatively easily (I would like to avoid using the command line for everything regarding it, like in git shell). Is there something else I should be aware of (please, on this don't point me to other questions ... they just give me a ton of info, and I'm not sure what is it that I should take as important, and what to disregard). I'm trying to cut some time, since I cannot spend all that time relearning hg, like I did for git. I've also heard git is c project, while mercurial is python ... is there any noticeable difference in speed. git was pretty speedy ... will I encounter some waiting while working. Notice: All my projects are of let's say, middle size ... mostly numerical simulations ... 10-15000 lines (medium size?)

  Read the article

• Hidden Features of PHP?

  - by George Mauer

  EDIT: This didn't really start as a hidden features of PHP topic, but thats what it ended up as, so go nuts. I know this sounds like a point-whoring question but let me explain where I'm coming from. Out of college I got a job at a PHP shop. I worked there for a year and a half and thought that I had learned all there was to learn about programming. Then I got a job as a one-man internal development shop at a sizable corporation where all the work was in C#. In my commitment to the position I started reading a ton of blogs and books and quickly realized how wrong I was to think I knew everything. I learned about unit testing, dependency injection and decorator patterns, the design principle of loose coupling, the composition over inheritance debate, and so on and on and on - I am still very much absorbing it all. Needless to say my programming style has changed entirely in the last year. Now I find myself picking up a php project doing some coding for a friend's start-up and I feel completely constrained as opposed to programming in C#. It really bothers me that all variables at a class scope have to be referred to by appending '$this-' . It annoys me that none of the IDEs that I've tried have very good intellisense and that my SimpleTest unit tests methods have to start with the word 'test'. It drives me crazy that dynamic typing keeps me from specifying implicitly which parameter type a method expects, and that you have to write a switch statement to do method overloads. I can't stand that you can't have nested namespaces and have to use the :: operator to call the base class's constructor. Now I have no intention of starting a PHP vs C# debate, rather what I mean to say is that I'm sure there are some PHP features that I either don't know about or know about yet fail to use properly. I am set in my C# universe and having trouble seeing outside the glass bowl. So I'm asking, what are your favorite features of PHP? What are things you can do in it that you can't or are more difficult in the .Net languages?

  Read the article

• Data aggregation mongodb vs mysql

  - by Dimitris Stefanidis

  I am currently researching on a backend to use for a project with demanding data aggregation requirements. The main project requirements are the following. Store millions of records for each user. Users might have more than 1 million entries per year so even with 100 users we are talking about 100 million entries per year. Data aggregation on those entries must be performed on the fly. The users need to be able to filter on the entries by a ton of available filters and then present summaries (totals , averages e.t.c) and graphs on the results. Obviously I cannot precalculate any of the aggregation results because the filter combinations (and thus the result sets) are huge. Users are going to have access on their own data only but it would be nice if anonymous stats could be calculated for all the data. The data is going to be most of the time in batch. e.g the user will upload the data every day and it could like 3000 records. In some later version there could be automated programs that upload every few minutes in smaller batches of 100 items for example. I made a simple test of creating a table with 1 million rows and performing a simple sum of 1 column both in mongodb and in mysql and the performance difference was huge. I do not remember the exact numbers but it was something like mysql = 200ms , mongodb = 20 sec. I have also made the test with couchdb and had much worse results. What seems promising speed wise is cassandra which I was very enthusiastic about when I first discovered it. However the documentation is scarce and I haven't found any solid examples on how to perform sums and other aggregate functions on the data. Is that possible ? As it seems from my test (Maybe I have done something wrong) with the current performance its impossible to use mongodb for such a project although the automated sharding functionality seems like a perfect fit for it. Does anybody have experience with data aggregation in mongodb or have any insights that might be of help for the implementation of the project ? Thanks, Dimitris

  Read the article

• How do I add a custom view to iPhone app's UI?

  - by Dr Dork

  I'm diving into iPad development and I'm still learning how everything works together. I understand how to add standard view (i.e. buttons, tableviews, datepicker, etc.) to my UI using both Xcode and Interface Builder, but now I'm trying to add a custom calendar control (TapkuLibrary) to the left window in my UISplitView application. My question is, if I have a custom view (in this case, the TKCalendarMonthView), how do I programmatically add it to one of the views in my UI (in this case, the RootViewController)? Below are some relevant code snippets from my project... RootViewController interface @interface RootViewController : UITableViewController <NSFetchedResultsControllerDelegate> { DetailViewController *detailViewController; NSFetchedResultsController *fetchedResultsController; NSManagedObjectContext *managedObjectContext; } @property (nonatomic, retain) IBOutlet DetailViewController *detailViewController; @property (nonatomic, retain) NSFetchedResultsController *fetchedResultsController; @property (nonatomic, retain) NSManagedObjectContext *managedObjectContext; - (void)insertNewObject:(id)sender; TKCalendarMonthView interface @class TKMonthGridView,TKCalendarDayView; @protocol TKCalendarMonthViewDelegate, TKCalendarMonthViewDataSource; @interface TKCalendarMonthView : UIView { id <TKCalendarMonthViewDelegate> delegate; id <TKCalendarMonthViewDataSource> dataSource; NSDate *currentMonth; NSDate *selectedMonth; NSMutableArray *deck; UIButton *left; NSString *monthYear; UIButton *right; UIImageView *shadow; UIScrollView *scrollView; } @property (readonly,nonatomic) NSString *monthYear; @property (readonly,nonatomic) NSDate *monthDate; @property (assign,nonatomic) id <TKCalendarMonthViewDataSource> dataSource; @property (assign,nonatomic) id <TKCalendarMonthViewDelegate> delegate; - (id) init; - (void) reload; - (void) selectDate:(NSDate *)date; Thanks in advance for all your help! I still have a ton to learn, so I apologize if the question is absurd in any way. I'm going to continue researching this question right now!

  Read the article

• Set maven to use archiva repositories WITHOUT using activeByDefault?

  - by Sam Levin

  I am very close to finally having a working setup with archiva and maven. The last thing that's really boggling me, is how to set up my internal and snapshot repositories - without using a profile which contains activeByDefault set to true. I am using a SUPER super pom - a company-wide pom which contains distributionManagement information for releases. I was thinking that I could specify the repositories in this pom, and configure the authentication settings in settings.xml? Can I use repositories tag without a profile? There should be no "profile" for my internal and snapshot repositories, as they will never change... What I'm trying to steer clear from, is using a "default" profile, which is active all the time. I hear activeByDefault is NOT a best practice and I don't intend to use it. With that said, how should I go about doing this? My internal repo is a mirror of the maven central repo, so I would like to lock down my developers to ONLY use our internal artifact server. Remember - I do NOT want a profile with activeByDefault set to true. I cannot stress this enough! Should I use Maven mirrors? Should I "add" additional repositories? If I take the repositories tag instead of the mirrors tag, will maven force builds to use ONLY my archiva settings, instead of the default maven central? Or is what I seek to accomplish able to be done using only the mirrors tag in maven? I know how to configure repo credentials when using repositories tag, but not with mirrors. How is this done? Is providing credentials for anything in mirrors tags the same as for anything in repositories tags? Am I missing something obvious? I've had it up to here with getting things up and running using maven. I know it will be worthwhile in the end, but it is surely causing me a ton of aggravation and resources seem to be sparse. Either that, or people are content using it however they please without regard to best-practices. Thank you

  Read the article

• YASR - Yet another search and replace question

  - by petronius31

  Environment: asp.net c# openxml Ok, so I've been reading a ton of snippets and trying to recreate the wheel, but I'm hoping that somone can help me get to my desination faster. I have multiple documents that I need to merge together... check... I'm able to do that with openxml sdk. Birds are singing, sun is shining so far. Now that I have the document the way I want it, I need to search and replace text and/or content controls. I've tried using my own text - {replace this} but when I look at the xml (rename docx to zip and view the file), the { is nowhere near the text. So I either need to know how to protect that within the doucment so they don't diverge or I need to find another way to search and replace. I'm able to search/replace if it is an xml file, but then I'm back to not being able to combine the doucments easily. Code below... and as I mentioned... document merge works fine... just need to replace stuff. protected void exeProcessTheDoc(object sender, EventArgs e) { string doc1 = Server.MapPath("~/Templates/doc1.docx"); string doc2 = Server.MapPath("~/Templates/doc2.docx"); string final_doc = Server.MapPath("~/Templates/extFinal.docx"); File.Delete(final_doc); File.Copy(doc1, final_doc); using (WordprocessingDocument myDoc = WordprocessingDocument.Open(final_doc, true)) { string altChunkId = "AltChunkId2"; MainDocumentPart mainPart = myDoc.MainDocumentPart; AlternativeFormatImportPart chunk = mainPart.AddAlternativeFormatImportPart( AlternativeFormatImportPartType.WordprocessingML, altChunkId); using (FileStream fileStream = File.Open(doc2, FileMode.Open)) chunk.FeedData(fileStream); AltChunk altChunk = new AltChunk(); altChunk.Id = altChunkId; mainPart.Document.Body.InsertAfter(altChunk, mainPart.Document.Body.Elements<Paragraph>().Last()); mainPart.Document.Save(); } exeSearchReplace(final_doc); } protected void exeSearchReplace(string document) { using (WordprocessingDocument wordDoc = WordprocessingDocument.Open(document, true)) { string docText = null; using (StreamReader sr = new StreamReader(wordDoc.MainDocumentPart. GetStream())) { docText = sr.ReadToEnd(); } Regex regexText = new Regex("acvtClientName"); docText = regexText.Replace(docText, "Hi Everyone!"); using (StreamWriter sw = new StreamWriter(wordDoc.MainDocumentPart.GetStream(FileMode.Create))) { sw.Write(docText); } } } } }

  Read the article

• Nasty redirect loop in WordPress (trailing slash, no trailing slash, and so on)

  - by Brett W. Thompson

  Hi, I read a ton of pages and tried lots of solutions but none have worked yet! My problem is that: test.asifa.net/asifa-wp Redirects to: test.asifa.net/asifa-wp/ Which redirects to the first page. What's a little bizarre is asifa-wp produces: <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>301 Moved Permanently</title> </head><body> <h1>Moved Permanently</h1> <p>The document has moved <a href="http://test.asifa.net/asifa-wp/">here</a>.</p> </body></html> Whereas asifa-wp/ produces an empty page but the following headers (curl -v output): * About to connect() to test.asifa.net port 80 (#0) * Trying 69.163.203.138... connected * Connected to test.asifa.net (69.163.203.138) port 80 (#0) > GET /asifa-wp/ HTTP/1.1 > User-Agent: curl/7.18.2 (i386-redhat-linux-gnu) libcurl/7.18.2 NSS/3.12.0.3 zlib/1.2.3 libidn/0.6.14 libssh2/0.18 > Host: test.asifa.net > Accept: */* > < HTTP/1.1 301 Moved Permanently < Date: Sun, 13 Jun 2010 05:40:12 GMT < Server: Apache < X-Powered-By: PHP/5.2.13 < X-Pingback: http://test.asifa.net/asifa-wp/xmlrpc.php < Set-Cookie: _icl_current_language=en; expires=Mon, 14-Jun-2010 05:40:12 GMT; path=/asifa-wp/ < Location: http://test.asifa.net/asifa-wp < Vary: Accept-Encoding < Content-Length: 0 < Content-Type: text/html; charset=UTF-8 .htaccess looks like: # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase /asifa-wp/ RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /asifa-wp/index.php [L] </IfModule> # END WordPress Any help at all would be tremendously appreciated!!!

  Read the article

• PHP 5.2 Function needed for GENERIC sorting of a recordset array

  - by donbriggs

  Somebody must have come up with a solution for this by now. We are using PHP 5.2. (Don't ask me why.) I wrote a PHP class to display a recordset as an HTML table/datagrid, and I wish to expand it so that we can sort the datagrid by whichever column the user selects. In the below example data, we may need to sort the recordset array by Name, Shirt, Assign, or Age fields. I will take care of the display part, I just need help with sorting the data array. As usual, I query a database to get a result, iterate throught he result, and put the records into an assciateiave array. So, we end up with an array of arrays. (See below.) I need to be able to sort by any column in the dataset. However, I will not know the column names at design time, nor will I know if the colums will be string or numeric values. I have seen a ton of solutions to this, but I have not seen a GOOD and GENERIC solution Can somebody please suggest a way that I can sort the recordset array that is GENERIC, and will work on any recordset? Again, I will not know the fields names or datatypes at design time. The array presented below is ONLY an example. UPDATE: Yes, I would love to have the database do the sorting, but that is just not going to happen. The queries that we are running are very complex. (I am not really querying a table of Star Trek characters.) They include joins, limits, and complex WHERE clauses. Writing a function to pick apart the SQL statement to add an ORDER BY is really not an option. Besides, sometimes we already have the array that is a result of the query, rather than the ability to run a new query. Array ( [0] => Array ( [name] => Kirk [shrit] => Gold [assign] => Bridge ) [1] => Array ( [name] => Spock [shrit] => Blue [assign] => Bridge ) [2] => Array ( [name] => Uhura [shrit] => Red [assign] => Bridge ) [3] => Array ( [name] => Scotty [shrit] => Red [assign] => Engineering ) [4] => Array ( [name] => McCoy [shrit] => Blue [assign] => Sick Bay ) )

  Read the article

• idiomatic property changed notification in scala?

  - by Jeremy Bell

  I'm trying to find a cleaner alternative (that is idiomatic to Scala) to the kind of thing you see with data-binding in WPF/silverlight data-binding - that is, implementing INotifyPropertyChanged. First, some background: In .Net WPF or silverlight applications, you have the concept of two-way data-binding (that is, binding the value of some element of the UI to a .net property of the DataContext in such a way that changes to the UI element affect the property, and vise versa. One way to enable this is to implement the INotifyPropertyChanged interface in your DataContext. Unfortunately, this introduces a lot of boilerplate code for any property you add to the "ModelView" type. Here is how it might look in Scala: trait IDrawable extends INotifyPropertyChanged { protected var drawOrder : Int = 0 def DrawOrder : Int = drawOrder def DrawOrder_=(value : Int) { if(drawOrder != value) { drawOrder = value OnPropertyChanged("DrawOrder") } } protected var visible : Boolean = true def Visible : Boolean = visible def Visible_=(value: Boolean) = { if(visible != value) { visible = value OnPropertyChanged("Visible") } } def Mutate() : Unit = { if(Visible) { DrawOrder += 1 // Should trigger the PropertyChanged "Event" of INotifyPropertyChanged trait } } } For the sake of space, let's assume the INotifyPropertyChanged type is a trait that manages a list of callbacks of type (AnyRef, String) = Unit, and that OnPropertyChanged is a method that invokes all those callbacks, passing "this" as the AnyRef, and the passed-in String). This would just be an event in C#. You can immediately see the problem: that's a ton of boilerplate code for just two properties. I've always wanted to write something like this instead: trait IDrawable { val Visible = new ObservableProperty[Boolean]('Visible, true) val DrawOrder = new ObservableProperty[Int]('DrawOrder, 0) def Mutate() : Unit = { if(Visible) { DrawOrder += 1 // Should trigger the PropertyChanged "Event" of ObservableProperty class } } } I know that I can easily write it like this, if ObservableProperty[T] has Value/Value_= methods (this is the method I'm using now): trait IDrawable { // on a side note, is there some way to get a Symbol representing the Visible field // on the following line, instead of hard-coding it in the ObservableProperty // constructor? val Visible = new ObservableProperty[Boolean]('Visible, true) val DrawOrder = new ObservableProperty[Int]('DrawOrder, 0) def Mutate() : Unit = { if(Visible.Value) { DrawOrder.Value += 1 } } } // given this implementation of ObservableProperty[T] in my library // note: IEvent, Event, and EventArgs are classes in my library for // handling lists of callbacks - they work similarly to events in C# class PropertyChangedEventArgs(val PropertyName: Symbol) extends EventArgs("") class ObservableProperty[T](val PropertyName: Symbol, private var value: T) { protected val propertyChanged = new Event[PropertyChangedEventArgs] def PropertyChanged: IEvent[PropertyChangedEventArgs] = propertyChanged def Value = value; def Value_=(value: T) { if(this.value != value) { this.value = value propertyChanged(this, new PropertyChangedEventArgs(PropertyName)) } } } But is there any way to implement the first version using implicits or some other feature/idiom of Scala to make ObservableProperty instances function as if they were regular "properties" in scala, without needing to call the Value methods? The only other thing I can think of is something like this, which is more verbose than either of the above two versions, but is still less verbose than the original: trait IDrawable { private val visible = new ObservableProperty[Boolean]('Visible, false) def Visible = visible.Value def Visible_=(value: Boolean): Unit = { visible.Value = value } private val drawOrder = new ObservableProperty[Int]('DrawOrder, 0) def DrawOrder = drawOrder.Value def DrawOrder_=(value: Int): Unit = { drawOrder.Value = value } def Mutate() : Unit = { if(Visible) { DrawOrder += 1 } } }

  Read the article

• Generating custom-form documents from base-form plus XML?

  - by KlaymenDK

  Hi all, this is my first stack overflow, and it's a complex one. Sorry. My task is to generate custom documents from a basic template plus some XML without having a custom form design element for each case. Here's the whole picture: We are building a Lotus Notes (client, not web) application for world-wide application access control; the scope is something like 400.000 users being able to request access to any of 1000+ applications. Each application needs its own request form -- different number of approvers, various info required, that sort of thing. We simply can't have a thousand forms in a database (one per application), and anyway their maintenance really needs to be pushed from the developers to the application owners. So instead of custom forms, we'd like to create a generic "template" form that stores a block of basic fields, but then allows application owners to define another block of fields dynamically -- "I want a mandatory plain-text field named 'Name' here, and then a date field named 'Due' here that must be later than today's date, and then ...". I hope this makes sense (if not, think of it as a generic questionnaire application). I pretty much have the structure in place for designing the dynamic fields (form builder GUI - XML-encoded data - pre-rendered DXL for injecting into a form), including mark-up for field types, value options, and rudimentary field validation instructions. My problem is generating a document with this dynamic content injected at the proper location (without needing a custom form design element for each case). Doing the dynamic content via HTML is out. The Notes client web rendering is simply way too poor, and it would be quite a challenge to implement things like field validation instructions, date selectors, and name look-ups. DXL, on the other hand, would allow us to use native Notes fields and code. As a tech demo, I've managed to implement a custom form generator that injects the pre-rendered DXL for the dynamic content into a base form; but as I said, we don't want a ton of custom form design elements. I've tried to implement a way to create a document with the "store form in document" flag set, but once I've created the document from the base form, I can't get DXL access to the stored form design, and so I can't inject my dynamic content. I know this is not something Notes was ever intended to do. Has anyone ever tried something like it (and gotten away with it)? Thanks for reading this far. With a boatload of thanks in advance, Jan Gundtofte-Bruun

  Read the article

• Passing password value through URL

  - by Steven Wright

  OK I see a lot of people asking about passing other values, URLS, random stuff through a URL, but don't find anything about sending a password to a password field. Here is my situation: I have a ton of sites I use on a daily basis with my work and oh about 90% require logins. Obviously remembering 80 bajillion logins for each site is dumb, especially when there are more than one user name I use for each site. So to make life easier, I drew up a nifty JSP app that stores all of my logins in a DB table and creates a user interface for the specific page I want to visit. Each page has a button that sends a username, password into the id parameters of the html inputs. Problem: I can get the usernames and other info to show up just dandy, but when I try and send a password to a password field, it seems that nothing gets received by the page I'm trying to hit. Is there some ninja stuff I need to be doing here or is it just not easily possible? Basically this is what I do now: http://addresshere/support?loginname=steveoooo&loginpass=passwordhere and some of my html looks like this: <form name="userform" method="post" action="index.jsp" > <input type="hidden" name="submit_login" value="y"> <table width="100%"> <tr class="main"> <td width="100" nowrap>Username:</td> <td><input type="text" name="loginname" value="" size="30" maxlength="64"></td> </tr> <tr class="main"> <td>Password: </font></td> <td><input type="password" name="loginpass" value="" size="30" maxlength="64"></td> </tr> <tr class="main"> <td><center><input type="submit" name="submit" value="Login"></center></td> </tr> </table> </form> Any suggestions?

  Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >