Search Results

Search found 32327 results on 1294 pages for 'ubuntu upgrade'.

Page 59/1294 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

• OCZ Vertex 2 not recognized by Ubuntu installer

  - by Zsub

  As I boot into the Ubuntu 10.10 (or 11.04, doesn't matter) live environment or installer, it just refuses to recognise my Vertex 2. It reports the disk as ATA and not supporting smart, shows no serial number, and doesn't list the size correctly. All fdisk tells me is Unable to read /dev/sda (it's the only storage in the PC). I'm now running a temporary install of Windows 7 off of it, which worked like a charm, so where am I going wrong with Ubuntu... Specs: Asus M4N68T-M LE V2 (BIOS 0702, most recent) OCZ Vertex 2 SSD 60 GB Amd Athlon II X4 640 Patriot PSD34G13332 4GB DDR3 ram (two banks) EDIT I installed a second drive, installed Ubuntu on that and booted, it recognised the SSD just fine. I'm now trying to apt-get upgrade the live-environment. I wonder if there is any way to sort of install Ubuntu from Ubuntu (I boot into the working install on the other drive, install it on the SSD and then boot from the SSD). EDIT2 Ok, so that doesn't work. The install detects the SSD, however, it cannot format it. EDIT3 After a fresh boot I can read out SMART-data and even perform a read-benchmark, but if I try to format it, or do a write-bench, it'll crap out and after that it says SMART is not supported. So basically it seems I can't write to the disk, as it will stop working when I do, I will try to run repeated read-benchmarks to see if that has any effect. EDIT4 I'm running several read benchmarks on the drive right now, they give results that are to be expected from an SSD. If the read-benches don't fail, I can use fdisk on the disk, but it is now stuck trying to re-read the partition table after issueing the 'w' command. EDIT5 Parted Magic did recognize the drive and with hdparm -I even could tell me the drive was in a frozen state. I powercycled it (just pull out the plug from the SSD and plug it back in) and it wasn't frozen anymore. After that I could upgrade the firmware on the drive (still using Parted Magic) and format it to Ext4. After I rebooted into the Ubuntu installer, it wouldn't get recognized and hdparm didn't want to talk to it saying HDIO_DRIVE_CMD(identify) failed: Invalid exchange. EDIT6 For some reason if I enable one of the RAID controllers (the one the SSD is connected to, obviously) Ubuntu will let me format it, mount it and write to it. The installer also recognizes it. However if the raid controller is enabled but no array is defined the motherboard can't boot from it :(

  Read the article

• Issues connection to Ubuntu via PuTTy

  - by user1787262

  I'm not sure this is the appropriate stack exchange site to post this question on. If not, please flag this for migration. I am trying to use PuTTy ssh into my ubuntu machine which is wirelessly connected to the same network. I originally ran ifconfig to get my ubuntu machines private network IP address. I then verified that ssh was running, I even ssh'd into my school network and then into the ubuntu machine itself. No problems yet. On my windows 8 machine I ran ipconfig to get my private network IPv4 address. I then pinged my ubunty machines IP and 100% of packets were received. I figured, "OK we are ready to use PuTTy to connect to my Ubuntu Machine". Keep in mind this was my first time using PuTTy. I tried entering the IP of my ubuntu machine in the PuTTy Config GUI but I got a connection timeout. At this moment I don't really know what's going on, SSH is running on port 22 of my Ubuntu machine and I can ping the machine why is it not connecting? (I tried [username]@ip too). So I went on my Ubuntu machine and ran nmap -sP 192.168.0.1/24 and found that my windows machines IP did not show up, the host is down. I'm at a lost in something I am not very familiar with. Would anyone be able to help me or direct me to some resources that would trouble shoot my problem? Thank you EDIT (ADDITION): tyler@tyler-Aspire-5250:~$ nmap -v 192.168.0.123 Starting Nmap 6.40 ( http://nmap.org ) at 2014-06-06 01:56 MDT Initiating Ping Scan at 01:56 Scanning 192.168.0.123 [2 ports] Completed Ping Scan at 01:56, 3.00s elapsed (1 total hosts) Nmap scan report for 192.168.0.123 [host down] Read data files from: /usr/bin/../share/nmap Note: Host seems down. If it is really up, but blocking our ping probes, try -Pn Nmap done: 1 IP address (0 hosts up) scanned in 3.14 seconds tyler@tyler-Aspire-5250:~$ nmap -Pn 192.168.0.123 Starting Nmap 6.40 ( http://nmap.org ) at 2014-06-06 01:56 MDT Nmap scan report for 192.168.0.123 Host is up (0.022s latency). Not shown: 998 filtered ports PORT STATE SERVICE 2869/tcp open icslap 5357/tcp open wsdapi Nmap done: 1 IP address (1 host up) scanned in 72.51 seconds

  Read the article

• Ubuntu unattended-upgrades stops apache

  - by Robbie

  This morning i was alerted to the fact that both apache instances serving my app were not responding to requests from my load balancer. I attempted apachectl restart and it said apache was not running. So, i started apache on both instances and got the service up again. I then followed the logs and worked out that both had performed upgrades via the unattended-upgrades package moments before they stopped responding. /var/log/unattended-upgrades/unattended-upgrades.log 2013-07-02 06:30:51,875 INFO Starting unattended upgrades script 2013-07-02 06:30:51,875 INFO Allowed origins are: ['o=Ubuntu,a=precise-security'] 2013-07-02 06:33:57,771 INFO Packages that are upgraded: accountsservice apache2 apache2-mpm-prefork apache2-utils apache2.2-bin apache2.2-common apparmor apport apt apt-transport-https apt-utils bind9-host binutils dbus dnsutils gnupg gpgv isc-dhcp-client isc-dhcp-common krb5-locales libaccountsservice0 libapt-inst1.4 libapt-pkg4.12 libbind9-80 libc-bin libc-dev-bin libc6 libc6-dev libcurl3-gnutls libdbus-1-3 libdbus-glib-1-2 libdns81 libdrm-intel1 libdrm-nouveau1a libdrm-radeon1 libdrm2 libexpat1 libfreetype6 libgc1c2 libgnutls-dev libgnutls-openssl27 libgnutls26 libgnutlsxx27 libisc83 libisccc80 libisccfg82 liblwres80 libruby1.8 libx11-6 libx11-data libxcb1 libxext6 libxml2 linux-firmware linux-image-virtual linux-libc-dev linux-virtual multiarch-support openssl perl perl-base perl-modules python-apport python-crypto python-keyring python-problem-report python-software-properties ri1.8 ruby1.8 ruby1.8-dev sudo tzdata update-manager-core 2013-07-02 06:33:57,772 INFO Writing dpkg log to '/var/log/unattended-upgrades/unattended-upgrades-dpkg_2013-07-02_06:33:57.772399.log' 2013-07-02 06:36:10,584 INFO All upgrades installed I'm running Ubuntu 12.04 on Amazon EC2 servers. I have unattended-upgrades installed and configured as follows: /etc/apt/apt.conf.d/50unattended-upgrades // Automatically upgrade packages from these (origin:archive) pairs Unattended-Upgrade::Allowed-Origins { "${distro_id}:${distro_codename}-security"; // "${distro_id}:${distro_codename}-updates"; // "${distro_id}:${distro_codename}-proposed"; // "${distro_id}:${distro_codename}-backports"; }; // List of packages to not update Unattended-Upgrade::Package-Blacklist { }; /etc/apt/apt.conf.d/20auto-upgrades APT::Periodic::Update-Package-Lists "1"; APT::Periodic::Unattended-Upgrade "1"; I've struggled to find documentation about what happens to running processes during an upgrade. - Is this expected behaviour? Or should unattended-upgrades restart apache after upgrading it? - What can I do to ensure apache is restarted correctly? Should I just blacklist the apache package?

  Read the article

• Ubuntu touch flashing failed/taking to long. Black screen! Redeploy help!

  - by Marius Rye

  So i'm brand new to the whole unlock, root and flashing thing. I just tried flashing Ubuntu touch on my Galaxy Nexus (international GSM/HSPA+) and everything seamed fine until the very end when i got this ERROR message. ERROR:phablet-flash:Installation is taking too long or an error occured along the way. I didn't know what to do so i disconnected my device (which was in Ubuntu recovery) and tried rebooting it from there, it worked "sort of". i got the Google logo with the unlocked icon then it continued to a black screen. In the installation guide on http://www.ubuntu.com/phone/install said i should: "try wiping the /data partition on your device and redeploy". the problem is that i don't know how to do this and i'm basically sitting here with a useless phone right now. I would be extremely grateful for some proffeexpert help.

  Read the article

• Problems while upgrading from 11.10 to 12.04

  - by Jignesh

  I was upgrading from ubuntu 11.10 to ubuntu 12.04 using the alternate cd method. Everything went fine upto installing upgrades, but during the cleanup phase , it asked me to remove obselete packages or not, and to close all open applications. I used Alt+Tab to view open applications, and then it just hanged, I could only move mouse ,entire screen got blank, and I was forced to restart , leaving the upgrade in middle. After restarting my ubuntu 12.04 is working fine , I think ubuntu got upgraded as only cleanup and restarting phases were remaining when I restarted, can there be problems with this ubuntu, or is this fine ?

  Read the article

• erlyvideo server doesn't start automatically after reboot

  - by electroid

  I have installed erlyvideo server on ubuntu 9.10 karmic koala. Everything works fine, but after server reboot I have to start erlyvideo server manually with /etc/init.d/erlyvideo start. I try allready update-rc.d and I think erlyvideo by default should start automaticaly. Any help will be appreciated. Here erlyvideo startup script located in /etc/init.d/erlyvideo: #!/bin/sh ### BEGIN INIT INFO # Provides: erlyvideo # Required-Start: $local_fs $network # Required-Stop: $local_fs $network # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: starts the erlyvideo streaming server # Description: starts the erlyvideo using erlang system ### END INIT INFO case "$1" in start) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; stop) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; restart) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; soft-restart) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; upgrade) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; reconfigure) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; reboot) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; ping) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; console) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; attach) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; attach-erl) cd /opt/erlyvideo && ./erts-5.8.4/bin/erl -name [email protected] -remsh [email protected] ;; *) echo $"Usage: $0 {start|stop|restart|soft-restart|upgrade|reboot|ping|console|attach}" exit 1 esac exit 0 And I have found S91erlyvideo in /etc/rc2.d next to S91apache2 which starts just fine on every reboot.

  Read the article

• How to perform feature upgrade in SharePoint2010 part2

  - by ybbest

  In my last post, I showed you how to perform feature upgrade and upgrade my feature from 0.0.0.0 to 1.0.0.1. In this post, I’d like to continue on this topic and upgrade the feature again. For the first version of my solution, I deploy a document library with a custom document set content type and then upgrade the solution so I index the application number column. Now , I will create a new version of the solution so that it will remove the threshold of the list. You can download the solution here. Once you extract your solution, the first version is in the original folder. In order to deploy the original solution, you need to run the sitecreation.ps1 in the script folder. The version 1.1 will be in the Upgrade folder and version 1.2 will be in the Upgrade2 folder. You need to make the following changes to the existing solution. 1. Modify the ApplicationLibrary.Template.xml as highlighted below: 2. Adding the following code into the feature event receiver. </pre> public override void FeatureUpgrading(SPFeatureReceiverProperties properties, string upgradeActionName, System.Collections.Generic.IDictionary<string, string> parameters) { base.FeatureUpgrading(properties, upgradeActionName, parameters); SPWeb web = GetFeatureWeb(properties); SPList applicationLibrary = web.Lists.TryGetList(ApplicationLibraryNamesConstant.ApplicationLibraryName); switch (upgradeActionName) { case "IndexApplicationNumber": if (applicationLibrary != null) { SPField queueField = applicationLibrary.Fields["ApplicationNumber"]; queueField.Indexed = true; queueField.Update(); } break; case "RemoveListThreshold": applicationLibrary.EnableThrottling = false; applicationLibrary.Update(); break; } } <pre> 3. Package your solution and run the feature upgrade PowerShell script. $wspFolder ="v1.2" $scriptPath=Split-Path $myInvocation.MyCommand.Path $siteUrl = "http://ybbest" $featureToCheckGuid="1b9d84cd-227d-45f1-92d4-a43008aa8fe7" $requiredFeatureVersion="1.0.0.1" $siteUrlOfFeatureToBeChecked="http://ybbest" AppendLog "Starting Solution UpgradeSolutionAndFeatures.ps1" Magenta & "$scriptPath\UpgradeSolutionAndFeatures.ps1" $siteUrl $wspFolder $featureToCheckGuid $requiredFeatureVersion $siteUrlOfFeatureToBeChecked Write-Host AppendLog "All features updated" "Green" References: Feature upgrade.

  Read the article

• What's the best way to re-install Ubuntu on my triple-boot system?

  - by TheX

  I have a triple boot system with Windows, Ubuntu 10.10 and 11.04, installed in that order, plus a "Data" Partition that has all my data, what I want to do is remove the 11.04, because I haven't booted into it for over a month, and I am afraid if I try to do any updates it will bork the system... I would like to install a fresh copy of 11.04 and leave the rest of the system intact, what is the best way to do this?

  Read the article

• Where do I file bugs for the Ubuntu One music client for Android?

  - by Jorge Castro

  I've recently started using the Ubuntu One Music streaming client for Android. From the web page it says that the android app is based on Subsonic. I want to file bugs on the app, mostly feature requests and things like that, and from looking at the screenshots, the application seems to be Subsonic preconfigured to use my U1 music collection. Is it appropriate for me to file feature requests with Subsonic, or is there a Launchpad project where we're supposed to file bugs which are then vetted and sent upstream?

  Read the article

• I have Ubuntu 12.04 installed on my pc and the pc hangs and does not restart more (translated)

  - by adail

  Translated from google My pc is an intel atom + Yes, it came with windows 7, formatted and installed Ubuntu 12.04, but the pc is unstable, it will not turn off properly and alone, appearing msg that there is no image signal, what to do? Meu pc é um Sim+ intel aton, veio com o windows 7, formatei e instalei o ubunto 12.04, mas o pc está instavel, ele não liga corretamente e desliga sozinho, aparecendo a msg que não ha sinal de imagem, o que fazer?

  Read the article

• Will deleting files on my computer delete them them in Ubuntu one?

  - by Shelley Demers

  OK. So I usually save my files online and not on my computer. I am hoping to be able to set up my Ubuntu One cloud to recognise changes made to documents and add new documents when synchronising. But not delete from the cloud, files I have deleted from my computer. Does anyone know if this is possible? I have searched around and can't figure out the answer to my question.I would appreciate any direction. Thank you so much!

  Read the article

• Why suspend / hibernate does not work in Ubuntu 10.10? (blank screen problem)

  - by agn0stic

  I've got a problem with Ubuntu 10.10 suspend / hibernation. When I try to do one of these actions, computer prepares but in the end a blank screen comes up with just a single underscore blinking. Computer becomes unresponsive to mouse/keyboard and only pressing power button on chasis restores it. Disks and coolers are working during the suspend / hibernation as if nothing happened. Can anyone give me some advice how to solve it? Thank you.

  Read the article

• How to get past "sending 'system' (92311 KB)..." when installing ubuntu on Nexus 7

  - by brew182

  I'm in the process of installing the Ubuntu image onto my Nexus 7 following these directions. I am on the step 4 and typed in phablet-flash -b and it downloaded some files, erased 'system' and is now on sending 'system' (92311 KB)... However, it has been on this step for about 3 hours now. I am assuming it shouldn't take this long so how can I go about getting out of this and restarting the flash without bricking my device?

  Read the article

• Crossover LAN connection between Ubuntu And Windows 7 is not working

  - by brett

  my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

  Read the article

• Unable to upgrade PEAR from 1.9.2 to 1.9.4

  - by user940768

  I am on a Ubuntu 11.10 and trying to upgrade from 1.9.2 to 1.9.4, but it simply don't work. Here are the commands I am following in sequence $ sudo apt-get install php-pear Reading package lists... Done Building dependency tree Reading state information... Done php-pear is already the newest version. The following packages were automatically installed and are no longer required: linux-headers-3.0.0-14-generic-pae libaccess-bridge-java-jni libaccess-bridge-java Use 'apt-get autoremove' to remove them. 0 upgraded, 0 newly installed, 0 to remove and 6 not upgraded. $ sudo pear channel-update pear.php.net Updating channel "pear.php.net" Channel "pear.php.net" is up to date $ sudo pear upgrade-all Nothing to upgrade-all $ sudo pear install –alldeps pear.phpunit.de/PHPUnit parsePackageName(): invalid package name "–alldeps" in "–alldeps" invalid package name/package file "–alldeps" Did not download optional dependencies: phpunit/PHP_Invoker, use --alldeps to download automatically phpunit/PHPUnit requires PEAR Installer (version >= 1.9.4), installed version is 1.9.2 phpunit/PHPUnit can optionally use package "phpunit/PHP_Invoker" (version >= 1.1.0) phpunit/Text_Template requires PEAR Installer (version >= 1.9.4), installed version is 1.9.2 phpunit/PHP_CodeCoverage requires PEAR Installer (version >= 1.9.4), installed version is 1.9.2 phpunit/PHP_CodeCoverage requires package "phpunit/Text_Template" (version >= 1.1.1) phpunit/PHP_CodeCoverage can optionally use PHP extension "xdebug" (version >= 2.0.5) phpunit/PHPUnit_MockObject requires PEAR Installer (version >= 1.9.4), installed version is 1.9.2 phpunit/PHPUnit_MockObject requires package "phpunit/Text_Template" (version >= 1.1.1) phpunit/PHP_TokenStream requires PEAR Installer (version >= 1.9.4), installed version is 1.9.2 No valid packages found install failed Any thoughts?

  Read the article

• Suggest methods for testing changes to "pam.d/common-*" files

  - by Jamie

  How do I test the changes to the pam.d configuration files: Do I need to restart the PAM service to test the changes? Should I go through every service listed in the /etc/pam.d/ directory? I'm about to make changes to the pam.d/common-* files in an effort to put an Ubuntu box into an active directory controlled network. I'm just learning what to do, so I'm preparing the configuration in a VM, which I plan to deploy in metal in the coming week. It is a clean install of Ubuntu 10.04 Beta 2 server, so other than SSH daemon, all other services are stock.

  Read the article

• How to mount /tmp in /mnt on EC2?

  - by Claudio Poli

  I was wondering what is the best way to mount the /tmp endpoint in the ephemeral storage /mnt on an EC2 instance and give the ubuntu user default write permissions. Some suggest editing /etc/rc.local this way: mkdir -p /mnt/tmp && mount --bind -o nobootwait /mnt/tmp /tmp However that doesn't work for me (files differs). I tried editing the default fstab entry: /dev/xvdb /mnt auto defaults,nobootwait,comment=cloudconfig 0 2 replacing /mnt with /tmp and and giving it a umask=0777, however it doesn't work because of cloudconfig. I'm using Ubuntu 12.04. Thanks.

  Read the article

• Horde complains that Imp is not running

  - by Eric J.

  I'm a mostly-Windows guy tasked with setting up email on an Ubuntu 12.04 instance at AWS and hit the following error: When I browse to Horde, after entering my administrative credentials, I get the error message: A fatal error has occurred imp is not activated. Details have been logged for the administrator. I am following the following, quite detailed guide http://www.exratione.com/2012/05/a-mailserver-on-ubuntu-1204-postfix-dovecot-mysql/ This is happening at Step 20, at the text Now fire up you web browser and navigate to your server at http://mail.example.com/ to verify that you can log in as the configured administrative mail user. (of course I used my actual domain). Questions Where is Horde logging the "details"? Any thoughts on why this might happen? I found Google hits suggesting that php5-mcrypt might be missing, but I verified it is installed and up-to-date in my case.

  Read the article

• Installing PHP Imagick with libmagickcore4

  - by Ali

  I have ImageMagick (version 6.6.9-7) on Ubuntu 12.04, which has libmagickcore4. When I tried to install PHP imagick, I received the following error: The following packages have unmet dependencies: php5-imagick : Depends: libmagickcore3 (>= 8:6.6.0.4) but it is not installable Depends: libmagickwand3 (>= 8:6.6.0.4) but it is not installable E: Unable to correct problems, you have held broken packages. Apparently, the problem is that php5-imagick is based on libmagickcore3 but a newer verion has been installed on my Ubuntu. Is there a way to instruct PHP imagick to use libmagickcore4?

  Read the article

• /var/lib/ureadahead/debugfs using up disk space

  - by Keyo

  Running Ubuntu 10.04 and nearly all my drive space is gone. # df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/ubuntu-root 7.3G 6.6G 327M 96% / none 245M 240K 244M 1% /dev none 249M 0 249M 0% /dev/shm none 249M 340K 249M 1% /var/run none 249M 0 249M 0% /var/lock none 249M 0 249M 0% /lib/init/rw /dev/sda1 228M 34M 183M 16% /boot Of course it's not mounted. I read that chmod 0 /sbin/debugfs could fix the problem, but now it just won't mount despite changing the permission to 777. This is a VM running on VirtualBox. I have done a file system check which ran fine. What is this directory and how can I remove it from the system?

  Read the article

• Crazy VM clock drift

  - by SimonJGreen

  This is taken from an Ubuntu 10.10 VM running on ESX5: Nov 3 21:58:50 server1 ntpd[21169]: adjusting local clock by 31.187370s Nov 3 22:02:36 server1 ntpd[21169]: adjusting local clock by 31.159808s Nov 3 22:05:18 server1 ntpd[21169]: adjusting local clock by 31.067579s Nov 3 22:07:59 server1 ntpd[21169]: adjusting local clock by 30.952187s Nov 3 22:11:38 server1 ntpd[21169]: adjusting local clock by 30.890147s According to the VMWare KB no kernel tweaks should be needed for Ubuntu 10.10 to maintain time to their standards. What's especially odd is the drift seems fairly consistent. Any help appreciated on this one!

  Read the article

• Mount /tmp in /mnt on EC2

  - by Claudio Poli

  I was wondering what is the best way to mount the /tmp endpoint in the ephemeral storage /mnt on an EC2 instance and give the ubuntu user default write permissions. Some suggest editing /etc/rc.local this way: mkdir -p /mnt/tmp && mount --bind -o nobootwait /mnt/tmp /tmp However that doesn't work for me. I tried editing the fstab: /dev/xvdb /tmp auto defaults,nobootwait,comment=cloudconfig 0 2 and giving it a umask=0777, however it doesn't work because of cloudconfig. I'm using Ubuntu 12.04.

  Read the article

• store image installation error in UEC

  - by selvakumar

  to my college final year project we planned to setup the private cloud on the two machines. I recently installed Ubuntu Enterprise Cloud (UEC) on two of my machines . I was trying to install the store image through WebUI. I was able to download Ubuntu 10.04 - (i386) image but while installing, it's giving me following error: - Command 'euca-upload-bundle' returned status code 1: Checking bucket: image-store-1296600766 Traceback (most recent call last): File "/usr/bin/euca-upload-bundle", line 231, in main() File "/usr/bin/euca-upload-bundle", line 214, in main bucket_instance = ensure_bucket(conn, bucket, canned_acl) File "/usr/bin/euca-upload-bundle", line 87, in ensure_bucket bucket_instance = connection.get_bucket(bucket) File "/usr/lib/pymodules/python2.6/boto/s3/connection.py", line 275, in get_bucket rs = bucket.get_all_keys(headers, maxkeys=0) File "/usr/lib/pymodules/python2.6/boto/s3/bucket.py", line 204, in get_all_keys headers=headers, query_args=s) File "/usr/lib/pymodules/python2.6/boto/s3/connection.py", line 342, in make_request data, host, auth_path, sender) File "/usr/lib/pymodules/python2.6/boto/connection.py", line 459, in make_request return self._mexe(method, path, data, headers, host, sender) File "/usr/lib/pymodules/python2.6/boto/connection.py", line 437, in _mexe raise e socket.error: [Errno 110] Connection timed out could anyone please help me?

  Read the article

• After closing the ssh terminal, the thin server is down

  - by Keating Wang

  I have a rails project run on the thin server(1.3.1) on a ubuntu server. I ssh to the server and start thin with command 'thin start -C config/thin.yml', following the thin.yml, port: 3000 log: log/thin.log timeout: 30 chdir: /home/byht/56platform/dev/tracker environment: production servers: 1 daemonize: true After thin starts successfully, I visit the project and it works well. Then, I close the terminal, I can also visit the pages that have been visited, but when I visit the pages that not been visited before closing ssh terminal, a "500" error appears on the page. I didn't find the error messages in the log file. I have tried start thin with nohup and sudo, but they are useless. I sign in the ubuntu server locally, then the problem disappears. But I need sign in the server to stat thin with ssh when I'm home.

  Read the article

• SVN help:: svn: invalid option: --trust-server-cert

  - by JP19

  Hi, I want to bypass certificate checking. I tried using svn --trust-server-cert update, but I get an error, svn: invalid option: --trust-server-cert. I am on ubuntu and the svn version is 1.5.4. Is there any other way to bypass the certificate? Ubuntu won't automatically update my svn to 1.6.xx, which I think has this option. (In any case, I have heard that 1.6.xx has compatibility problems with some apache modules so is not fully safe to install?). Anyone with a suggestion? Thanks JP

  Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >