Search Results

Search found 17973 results on 719 pages for 'x frame options'.

Page 590/719 | < Previous Page | 586 587 588 589 590 591 592 593 594 595 596 597  | Next Page >

• Western Digital HDD disappears and reappears in BIOS

  - by tbkn23

  I know many people asked about similar problems, but I have a very specific case where I can't understand what's going on... I have a 3TB Western Digital Caviar Green disk connected in my Desktop, that also has a seagate 1.5TB disk and 2 SSD drives (OCZ and Sandisk). After working fine for quite some time (probably more than a year), suddenly my Caviar Green drive disappeared from windows. I checked the BIOS, and it wasn't there either. I opened my PC, played with the connectors, power, etc, but nothing helped. Even tried switching connectors with those of the 1.5TB disk, and nothing changed, the 1.5TB seagate was there, but the 3TB WD was not. Ok, now for the strange part. I have another desktop at home, so I took out my 3TB drive, connected it there, and it worked fine! I copied the most important files out of it, and then made another attempt in the original desktop. Surprise! It now appeared in the BIOS and worked fine! I even ran the SMART test with the WD tools and it said everything was intact. It doesn't end here. After leaving it overnight in the original desktop, it disappeared again in the morning. I repeated the entire process, connecting it to the second desktop, and there it is again working fine. Now for my question... Whats going on? The disk seems to be appearing on/off in my original Desktop, while other drives there work fine. SMART test says the disk is fine. Any ideas? Is the disk defective and should be replaced? Or maybe there's a problem with the controller in the desktop? I'm using a Gigabyte GA-880GA-UD3H motherboard and tried connecting the drive to both bridges (SATA2 and SATA3 bridges). Thanks EDIT: Power options are set never to turn off hard drives:

  Read the article

• The best way to hide data Encryption,Connection,Hardware

  - by Tico Raaphorst

  So to say, if i have a VPS which i own now, and i wanted to make the most secure and stable system that i can make. How would i do that? Just to try: I installed debian 7 with LVM Encryption via installation: You get the 2 partitions a /boot and a encrypted partition. When booting you will be prompted to fill in the password to unlock the encryption of the encrypted partition, Which then will have more partitions like /home /usr and swapspace which will automatically mount. Now, i do need to fill in the password over a VNC-SSL connection via the control panel website of the VPS hoster, so they can see my disk encryption password if they wanted to, they have the option if they wanted to look at what i have as data right? Data encryption on VPS , Is it possible to have a 100% secure virtual private server? So lets say i have my server and it is sitting well locked next to me, with the following examples covered bios (you have to replace bios) raid (you have to unlock raid-config) disk (you have to unlock disk encryption) filelike-zip-tar (files are stored in encrypted archives) which are in some other crypted file mounted as partition (archives mounted as partitions) all on the same system So it will be slow but it would be extremely difficult to crack the encryption. So to say if you stole the server. Then i only need to make the connection like ssh safer with single use passwords, block all incoming and outgoing connections but give one "exception" for myself. And maybe one for if i somehow lose my identity for the "exeption" What other overkill but realistic security options are available, i have heard about SElinux?

  Read the article

• How to configure default text selection behavior in Windows XP, 7? (eg. mouse click selects entire word vs. mouse click inserts an active cursor)

  - by Mouse of Fury

  I find the mouse click behavior of Windows XP and Windows 7 annoying and intrusive. I don't remember Windows NT being quite this bad, or MacOS 7 - 10 which I used in the nineties. When I'm using a browser and I click on a text field - for example, the address bar, or a search box - the first thing which happens is the entire field is selected.Subsequent clicks seem to select parts of words, often deciding arbitrarily to exclude or include adjacent punctuation. The same in Excel and other apps, and when trying to rename files, so I'm assuming this behavior comes from a system-wide text handling routine. I frequently want to edit text, cut out or replace odd parts of the insides of words or chunks of sentences, and often find that to get a simple cursor to insert I have to click the mouse up to 4 times in succession. I've had to do a lot of this recently and it has been driving me insane. Is there a place at the system level where this can be configured? In a perfect world, I'd like a single click on a new text area to insert a cursor point, and a rapid double click to select the entire area. Words or text within the area could be selected by inserting a cursor, holding down the mouse button and dragging to the exact point where I want the selection to end - even if that's in the middle of a word. No, I don't need or want Windows to "smart select" a word or sentence for me. I've looked in the Mouse and Accessibility Options control panels (Windows XP). Haven't found anything even close. Thanks -

  Read the article

• Memory overcommitment on VmWare ESXi 5.0

  - by Tibor

  I would like to understand better the possibilities of VmWare ESXi memory overcommitment. I've read this paper from VmWare, so I am familiar with general concepts, such as hypervisor swapping, memory balooning and page sharing. It seems that a combination of these techniques allows for quite a large degree of overcommitment. However, I am not sure. I am deploying a virtual test lab comprising of 4 identical sets of virtual servers and workstations and a couple of virtual router instances. Overall, I expect to be running around 20 virtual machines with Windows XP, Windows 7 and Ubuntu for workstation hosts as well as CentOS and Windows 2008 Server instances for servers. The problem is, however, that the host machine only has 12GB of RAM and I don't have an option to stuff in some more. I would like to know what is the best option to configure hosts in order to achieve reasonable performance within the constrains. I have these two options: Allocate as little as possible of RAM to each virtual machine. Allocate an extraordinary amount (such as 4 GB per instance) and let the baloon driver do the rest. Something else? Which would work better? Machines will mostly be idle, so I don't have any major performance expectations, but they should run reasonably smoothly nevertheless.

  Read the article

• Network structure --> Server 2k8r2 <--> Livebox <--> Router <--> Other PCs

  - by Yusuf

  I have a Livebox connection to the Internet and I have set up my network as follows: - Livebox <--> Win2k8R2 Server - Livebox <--> Netgear N150 Router - Router <--> Other PCs Therefore, in my LAN, - the Livebox has IP address 192.168.1.1, - the Router 192.168.1.12 (when accessed from the Livebox or the server), - the Router 10.0.0.1 (when accessed from the PCs connected to the Router), - the server 192.168.1.2, - the PCs 10.0.0.x I was using a previous configuration, which was as follows: - Livebox <--> Netgear N150 Router - Router <--> Win2k8R2 Server - Router <--> Other PCs Everything was simple, and I just had to forward all ports for incoming connection on the Livebox to the Router, and then forward the specific ports to the Server as needed (it must be however noted that any server I use is found on the Win2k8R2 server itself). In this previous configuration, the IP addresses were as follows: - Livebox 192.168.1.1 - Router 192.168.1.12 (when seen from Livebox) - Router 10.0.0.1 (when seen from server & PCs connected to it) - Server 10.0.0.2 - PCs 10.0.0.x So now of course, my port-forwarding does not work anymore since the server is not connected (directly) to the Router. What I would like to know is how do I configure the Livebox and Router to still have the features like before? From what I understand of networks (which is very limited, btw), I see these options: Make the router assign IPs like 192.168.1.x (but then I want the forwarding to be done from the router itself, is it possible?) The forwarding on the router to the server uses IP address 10.0.0.2. I could change it to 192.168.1.2 (Is that even possible, does it work?) Forward all ports from the Livebox itself to the server, and then manage them there (Is software-based port-forwarding as secure as hardware-based?)

  Read the article

• Backup data from RAID 1 disk out of its server

  - by Doomsday

  I'm facing with a pretty easy problem in my opinion. I've extracted a working disk from a RAID1 and I'm looking to copy only data (FS and RAID configuration doesn't matter) into another location (another FS). My problem is I'm not able to mount properly this disk into another linux. I've first looked the partition table : # fdisk -l /dev/sdc Disk /dev/sdc: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 63 1249535699 624767818+ fd Linux raid autodetect /dev/sdc2 1249535700 1250017649 240975 fd Linux raid autodetect /dev/sdc3 1250017650 1250258624 120487+ 82 Linux swap / Solaris I've understood I should use dmraid tools. Once installed : # cat /proc/mdstat Personalities : md0 : inactive sdc1[1](S) 624767744 blocks unused devices: <none> And some other informations : # mdadm --examine /dev/sdc1 /dev/sdc1: Magic : a92b4efc Version : 0.90.00 UUID : 8f292f54:7e5aef72:7e5ab5fd:b348fd05 Creation Time : Mon Jun 2 03:39:41 2008 Raid Level : raid1 Used Dev Size : 624767744 (595.82 GiB 639.76 GB) Array Size : 624767744 (595.82 GiB 639.76 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Update Time : Tue Feb 7 22:34:59 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Checksum : a505b324 - correct Events : 15148 Number Major Minor RaidDevice State this 1 8 1 1 active sync /dev/sda1 0 0 8 17 0 active sync /dev/sdb1 1 1 8 1 1 active sync /dev/sda1 From here, I've tried to mount but I'm not comfortable with dmtools and how it's working. # mount /dev/sdc1 /mnt/sdc1 mount: unknown filesystem type 'linux_raid_member' # mount /dev/md0 /mnt/sdc1 mount: /dev/md0: can't read superblock I've seen some options to alter RAID array with mdadm but I only want to copy data on its filesystem before wiping them... Anyone has a clue ?

  Read the article

• How to repair a corrupted Excel file

  - by SjoerdV

  I'm trying to restore some files for a friend who messed up a USB stick by pulling it out of the computer too soon. By searching invisible partitions I was able to restore the files. All files are intact, except 1 excel file that seems to be corrupted. I've googled about ways to repair an Excel file, because the default repair options in Excel 2003-2010 do not work for this file. I've came across a numerous third-party apps, of which the one seemes to be able to do the job: Recovery Toolbox for Excel. Of-course, this and all other apps I found require a purchase to actually repair the file. It seems a bit silly to pay 30 dollars for a one time thing, and something that is not for myself. So, I would like to keep that as a last-resort option. Is there anything I can try to fix this? I've attached a screenshot of how the file looks when I open it on my OSX when converted to a HTML file (to view the code), for the option that it could be a character set problem.

  Read the article

• Password-less login into localhost

  - by Brad

  I am trying to setup password-less login into my localhost because it's required for a tutorial. I went through the normal steps of generating an rsa key and appending the public key to authorized_keys but I am still prompted for a password. I've also enabled RSAAuthentication and PubKeyAuthentication in /etc/ssh_config. Following other suggestions I've seen, I tried: chmod go-w ~/ chmod 700 ~/.ssh chmod 600 ~/.ssh/authorized_keys But the problem persists. Here is the output from ssh -v localhost: (tutorial)bnels21-2:tutorial bnels21$ ssh -v localhost OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: Connecting to localhost [::1] port 22. debug1: Connection established. debug1: identity file /Users/bnels21/.ssh/id_rsa type 1 debug1: identity file /Users/bnels21/.ssh/id_rsa-cert type -1 debug1: identity file /Users/bnels21/.ssh/id_dsa type -1 debug1: identity file /Users/bnels21/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9 debug1: match: OpenSSH_5.9 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 1c:31:0e:56:93:45:dc:f0:77:6c:bd:90:27:3b:c6:43 debug1: Host 'localhost' is known and matches the RSA host key. debug1: Found key in /Users/bnels21/.ssh/known_hosts:11 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/bnels21/.ssh/id_rsa debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Offering RSA public key: id_rsa3 debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Trying private key: /Users/bnels21/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive Password: Any suggestions? I'm running OSX 10.8.

  Read the article

• Software/hardware to build video streaming server?

  - by Sasha Yanovets

  I am looking for a video streaming server solution, something like online TV server, with ability to make live broadcasts in the internet. What software could you recommend for that? What kind of hardware it should run on, should be there anything special? I am looking for a solution that could be scaled up to at least 1000 simultaneous users online with good resolution of video. I think it is good to have general answer on what direction to choose. But here more details on my specific case: I just looking for a solution almost from scratch. We have some video content that we've produced, but it is not delivered over internet yet. We do not tied to any particular vendor for now. We want to make 24 hours of steaming three 8 hour blocks with change of content every day. We want the ability to make regular live broadcasts. I guess we will need to have several options of streaming quality (low ~56 kb/s mid ~273 kb/s). Some terms just foreign to me (like play-truncation rate), if you could point out what parameters we should avare of, it would be great. Uplink to the internet is to be determined. We plan to start from something and scale up on the way. If you are already have some kind of media streaming server, just describe its configuration here (hardware, OS, software), peak number of concurrent users it serves. I think it could help people approaching this task.

  Read the article

• why won't php 5.3.3 compile libphp5.so on redhat ent

  - by spatel

  I'm trying to upgrade to php 5.3.3 from php 5.2.13. However, the apache module, libphp5.so will not be compiled. Below is a output I got along with the configure options I used. The configure statement is a reduced version of what I normally use. ========== './configure' '--disable-debug' '--disable-rpath' '--with-apxs2=/usr/local/apache2/bin/apxs' ... ** ** ** Warning: inter-library dependencies are not known to be supported. ** ** ** All declared inter-library dependencies are being dropped. ** ** ** Warning: libtool could not satisfy all declared inter-library ** ** ** dependencies of module libphp5. Therefore, libtool will create ** ** ** a static module, that should work as long as the dlopening ** ** ** application is linked with the -dlopen flag. copying selected object files to avoid basename conflicts... Generating phar.php Generating phar.phar PEAR package PHP_Archive not installed: generated phar will require PHP's phar extension be enabled. clicommand.inc pharcommand.inc directorytreeiterator.inc directorygraphiterator.inc invertedregexiterator.inc phar.inc Build complete. Don't forget to run 'make test'. ============= php 5.2.13 recompiles just fine so something is up with 5.3.3. Any help would be greatly appreciated!!

  Read the article

• Xen domU mem-set issue

  - by Casper Langemeijer

  I'm running into a problem on my xen 4.0.1 server (debian squeeze) My host has 32G of memory, Domain-0 has 2048 M assigned to it. (scaled down with xm mem-set Domain-0 2048) top in Domain-0 confirms this. I created a virtual machine config file (using xen-tools) with the following options: memory = '512' maxmem = '2048' Both host and guest machines are running the standard 2.6.32-5-xen-amd64 debian kernel. 'xm create' creates a virtual machine with 512MB of memory as expected. Then 'xm mem-set domU 1024' will not expand the memory to 1024MB running 'xm mem-set domU 400' does set the memory to about 400MB Then 'xm mem-set domU 1024' will expands the memory back to 512MB Based on this, you would say that xm ignores the maxmem and silently sets maxmem to 512, but in the output of xm top the MAXMEM column reads 2G. the MEM column will not go over 512M. The output of xm list tells another story, it shows 1024 when I 'xm mem-set domU 1024'. I've googled myself all away around the internet for this issue and found that most people don't scale back Domain-0. I know I've seen a bugreport about the issue I'm experiencing, but can't find it anymore. Does anyone see what I'm doing wrong here? Hmm.. I just upgraded my kernel to the one provided by debian backports. The issue has gone.

  Read the article

• Moving a lot of small files between servers using rsync

  - by Adirael

  Hello guys, I'm moving a lot of files (about 2 millions) between two servers on different locations using rsync over ssh, it seems to work fine but I just realised I'm losing some files on the process. I got server 1, with the original data, and server 2, with the copy. Server 1 runs CentOS 5 and Server 2 runs on Ubuntu 10. I'm doing the transfer on the Server's 2 command line like this: rsync -e ssh -avzn usr@server1:/remote/path /local/path The first file movement I did using tar, but I didn't though of piping it through ssh and it failed cause the disk on server 1 was almost full, so I transfered it anyways (it was about 200GB) and got about 80% of the files. Then I piped another tar with the rest of the files (they're in folders, I got 100 folders with about 30 subfolders each, with files inside) and now I got everything on server 2. I wanted to be sure, so I my two options are getting the md5sum of all the files and check them or running an rsync on server 2 against server 1, that's what I did. It got some missing stuff and now it says there's nothing more to do (DRY RUN). But I got at least two files that are missing inside a subfolder. I ran that same rsync on that folder, but still dry run. Am I doing something wrong? Thanks, and sorry for the wall of text.

  Read the article

• Why isn't Apache Basic authentication working?

  - by Brad

  I just upgraded Apache from it's 2003 build, to a squeaky-clean, brand-new 2.4.1 build. All seems pretty good except for one glaring thing: In my httpd.conf file I have the following: <Directory /> AllowOverride none Options FollowSymLinks AuthType Basic AuthName "Enter Password" AuthUserFile /var/www/.htpasswd Require valid-user </Directory> This should allow only users in the specified auth file to access the server - just as it had under the older version of Apache. (Right?) However, it's not working. Requests are granted with no authentication provided. When I switch logging to LogLevel Debug, for the accesses, it says: [Sat Mar 24 21:32:00.585139 2012] [authz_core:debug] [pid 10733:tid 32771] mod_authz_core.c(783): [client 192.168.1.181:57677] AH01626: authorization result of Require all granted: granted [Sat Mar 24 21:32:00.585446 2012] [authz_core:debug] [pid 10733:tid 32771] mod_authz_core.c(783): [client 192.168.1.181:57677] AH01626: authorization result of <RequireAny>: granted I really don't know what this means - and I (to the best of my knowledge) don't have any "Require all granted" or "" statements in any of my files. Any ideas why this isn't working, or where to debug??

  Read the article

• need to bring back win 7

  - by user290513

  I like making music and playing games and occasionally do some Photoshop. I had a windows 8 computer but my mouse pointer always got stuck, so to try out something new I installed Ubuntu. here is how I installed it: Went to advanced statup options clicked on "use a device" after plugging in my bootable USB with Ubuntu replaced my windows 8 and installed Ubuntu 14.04 LTS I hope I did it correctly though. So after a few months I could've really find out a good Audio Production (not LMMS, because I use Stagelight) software nor something that could be familiar to the UI of Photoshop. So I decided to bring back Windows, but because of the bad experience of 8 I thought about bringing back win 7 So I used an app named WinUSB to make my bootable USB drive after formatting it to NTFS in GParted But when I go to my grub menu, my USB doesn't show up and my PC being a UEFI device. I don't know how to get to the bios of my device. Can somebody tell how to install Windows 7 completely and deleting Ubuntu or at least give me a link to a tutorial. I have a netbook: it is an Acer Aspire One 725. I'm fine with using commands in terminal and another thing that my laptop doesn't have a CD drive or reader, I can't put a CD inside

  Read the article

• Debian Wheezy (testing) df reported volume size

  - by TheRoadrunner

  I am a bit confused about the /dev/sda* references since I installed Wheezy instead of Squeeze on a testing box. fdisk -l returns: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e9623 Device Boot Start End Blocks Id System /dev/sda1 * 2048 480278527 240138240 83 Linux /dev/sda2 480280574 488396799 4058113 5 Extended /dev/sda5 480280576 488396799 4058112 82 Linux swap / Solaris This seems correct. But df -h /dev/sda (and /dev/sda1 and /dev/sda2 and /dev/sda5) returns: Filesystem Size Used Avail Use% Mounted on udev 10M 0 10M 0% /dev The same happens with every entry under /dev/disk/by-id and /dev/disk/by-path. Only one of two entries under /dev/disk/by-uuid returns the correct volume size: df -h /dev/disk/by-uuid/cacdbad6-7e6b-4e80-84ba-e3c77ef48796 Filesystem Size Used Avail Use% Mounted on /dev/disk/by-uuid/cacdbad6-7e6b-4e80-84ba-e3c77ef48796 229G 22G 196G 11% / Contents of /etc/fstab: # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> # / was on /dev/sda1 during installation UUID=cacdbad6-7e6b-4e80-84ba-e3c77ef48796 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=45840d13-ee36-4e77-8e73-16cbdff25eb1 none swap sw 0 0 /dev/sr0 /media/cdrom0 udf,iso9660 user,noauto 0 0 /dev/fd0 /media/floppy0 auto rw,user,noauto 0 0 It seems all other references than the uuid points to the swap partition. Is this because Wheezy is in testing, and should it be reported as an error?

  Read the article

• Use GRUB/GRUB2 to PXE boot OS image

  - by Jack

  Asked this in stackoverflow but they recommended I post this here: Here is the situation I am in: I currently have a Windows drive that boots XP. The BIOS does not support PXE booting so this is out of the question. Therefore, I was thinking I could install a customized GRUB bootloader on it instead such that it will have the option to PXE boot an image from a DHCP server connected to it and have the option to load Windows as it normally does (two items in menu). The catch is it may need to be automated (meaning no keyboard), so is there any way to run a script pre-boot during GRUB loading that determines if DHCP / TFTP servers are running and attempt to PXE boot an image from the network (and if not, say timeout of 10 seconds, regularly boot from Windows drive)? If this is not possible, what are some other options / suggestions? I was reading up on grub4dos as well but I'm not sure that is what I need. FWIW, I'm free to do whatever I want to the drive. I'd really appreciate some help on this as I'm not sure where to start. Thanks!

  Read the article

• How do I access my webserver on my stationary from my laptop?

  - by Steven

  I'm running Apache on my stationary and I would like to access a website through my laptop. This is some of the Apache config: NameVirtualHost 127.0.0.1:80 <VirtualHost 127.0.0.1:80> ServerName mysite.com DocumentRoot I:/wamp/www/mysite/ </VirtualHost> ServerName localhost:80 <Directory /> Options FollowSymLinks AllowOverride all Order deny,allow Deny from all </Directory> On my laptop I've added the following to the HOSTS file: 10.0.0.3 mysite.com But accessing the page through mysite.com is not very successfull. If I enter the IP address directly, I only get a Forbidden message. What do I need to do in order to get this to work? Update I'm runing WAMPSERVER 2.1 (Apache 2.2.17) Apache is up and running I can ping 10.0.0.3 from laptop I'm not able to ping http://mysite.com from laptop IE gives me a 403 Forbidden - The website declined to show this webpage The only log that get's entries when trying to access the website from my laptop, is access.log. access.log 10.0.0.4 - - [13/Jun/2011:10:14:04 +0200] "GET / HTTP/1.1" 403 202 apache_error.log [Mon Jun 13 10:08:16 2011] [error] VirtualHost localhost:0 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results UPDATE 2 My apache config has the following entry: AllowOverride all Order Deny,Allow Deny from all Allow from 127.0.0.1 Could it be that this Allow from is stopping other computers accessing the page?

  Read the article

• Triple-Boot + 4 partition Limit

  - by dsimcha

  I just bought a new hard drive so that I could convert my XP-only machine into an XP-Ubuntu-Windows 7 triple boot machine. Since the drive is absurdly huge (1 TB) I wouldn't mind throwing ReactOS into the mix, too. I just found out that master boot records are limited to 4 entries, meaning 4 primary partitions. I had Windows XP set up on my old drive as a boot partition, a program files partition and a media partition. Since I really didn't want to install XP from scratch, I cloned this setup on my new drive. This leaves me one MBR partition entry for installing Windows 7, Ubuntu and ReactOS. I'd like to avoid having to install XP from scratch like the plague, partly because it's supposed to be a safety net in case things go wrong with my other OS's and because I've invested a lot of time getting it set up exactly the way I like it. Here are the options I've considered and why I don't like them: Install Windows 7 on my media partition. This would work, but I prefer to keep my media partition completely separate from any OS, so that I can reformat an OS partition without affecting my media partition at all. Use wubi or something to install Ubuntu in the same partition as something else. Again, this is brittle. Move all my media to a logical drive on an extended partition. Create another logical drive on this extended partition for Ubuntu. The problem here is that extended partitions are rather brittle--if you nuke one, it renders the rest useless. Just put the old drive back in my computer and run XP off it. Use the new one for the other OS's. The problem here is that the old drive is slower and uses extra power, generates extra heat, etc. Can anyone suggest any other possibilities that I may have overlooked?

  Read the article

• Software raid 0 with six disks performance

  - by user134880

  I have some problems with disk performance. I have 6 x WD 500Gb RE4 disks. Each disk gives 135Mb/sec throughput. All measurements are made with hdparm with options "-tT" (I know that it is just synthetic test, but I need some start point to make measurements). I have controller with Sil3124 x 4 ports PCI Express 1x So... RAID0 on controller with 2 disks gives 200Mb/s - ok, pcie limit. RAID0 on motherboard with 2 disks gives 270Mb/s - niceeee :) RAID0 on contorller with 4 disks gives 200Mb/s - ok, pcie limit. RAID0 on controller with 4 disks + 1 disks on motherboard = 340Mb/s ... :( RAID0 on controller with 4 disks + 2 disks on motherboard = 300Mb/s .... why? Any ideas? Maybe need more cpu power? Now there is Pentium D Dual core 2.8Ghz, 4Gb RAM. It is dedicated box for storage.. no other activity.

  Read the article

• Running .NET code in XML file [closed]

  - by Stuart McIntosh

  We have 2 servers, 1 already configured with .net which works fine and a new one which appears to be configured the same but when I open an xml page in Internet Explorer it complains about the <% tag. We have IIS on win srvr 2003 SP2. The website is configured with .NET 1.1.4322. In ISAPI extensions have set the .XML extension to use c:\windows\microsoft.net\framework\v1.1.4322\aspnet_isapi.dll But the page: <property name="documentmaxage" value="0"/> <property name="documentmaxstale" value="0"/> <var name="m_Prompt_Path" /> <form id="InitVoiceXmlDoc"> <block> <assign name="m_Prompt_Path" expr="&quot;<% Response.Write(Request.QueryString["m_Prompt_Path"]); %>&quot;"/> </block> </form> gives the error: The XML page cannot be displayed Cannot view XML input using XSL style sheet. Please correct the error and then click the Refresh button, or try again later. The character '<' cannot be used in an attribute value. Error processing resource 'http://localhost:11119/fails.xml'. Lin... &quo... We have the same config on another server which works fine. So are there other options apart from the ISAPI extensions that I need to look at

  Read the article

• Can't install Hyper-V in Windows 8 Pro. Causes boot loop, pain & suffering

  - by Nick

  Hardware: Intel i7 2600K (not overclocked, SLAT compatible, virt. features enabled in bios) Asus Maximus IV Extreme-Z (Z68) 16Gb RAM 256Gb SSD Other non-trivial working parts Adding Hyper-V is causing a boot loop resulting in an attempt at automatic repair by Windows 8 after the second or third loop: I'm trying to get the Windows Phone 8 SDK installed and I've narrowed down my troubles to the Hyper-V feature in Win8. This is required to run the WP8 emulator and there are no install options to omit this feature. My first attempt completely borked the OS as I did not have a recent restore point or system image, so I did a completely clean install and made plenty of backups/restore points. I skipped the SDK install and went straight for the windows feature add-on for Hyper-V. This confirmed that Hyper-V is the issue as the same behavior resulted. I cannot find any hint in the Event Logs. Cancelling automatic recovery causes the same behavior to repeat. I don't have any other VM products installed. My only recourse is to use a restore point, try something else, install it again, and see what happens. No luck so far. I'm on my 10th attempt here. Any help would be much appreciated.

  Read the article

• Start Chrome by command line, but adding some arguments to make it login into your Google account automatically

  - by jim

  Is there a way to start Chrome calling it from the command line (using Linux), but providing it some argument to make it login into some Google account automatically? I'm looking for something like google-chrome -account foo -pass bar that I can easily put in a bash script later. A little background: I have a laptop connected to my TV, which is currently using just a mouse for user interaction. There's no google account logged in by default, and that's the way I want to keep it, so my kids can't come across videos and pictures in google and youtube that they are not supposed to see (e.g.: adult content, or anything marked as not appropriate for kids by the google's safe search filters). The bad thing about this is that there are some music videos in youtube that requires you to be logged in to see, usually those we (the adults) used to sing when playing karaoke... as the only input available is a mouse, I'm looking for a way to start with my google account without having to type the whole thing usin the on-screen keyboard. You may think "Why you can't use the keyboard, if the laptop is right there?". Well, it's in a kind of uncomfortable position - too high for me without a chair or something, as it's right above the furniture in where the TV is located. Is there a way to make this scriptable? If not, do you know any other workaround? Note: using the remember me after logging off or alike options are discarded, as the safe-search chrome version must be always the default version to run.

  Read the article

• Disable internal display on Macbook Pro without closed lid mode?

  - by jslaker

  I have an early 2007 Macbook Pro running 10.5 that I've recently set up on a KVM with my primary desktop system. The problem I've run into is that I have a 20" 1680x1050 LCD, and OS X only provides options to mirror at the resolution of the built-in display or to span. Since the built-in display runs at 1440x900, this leads to running my LCD at non-native res and a fuzzy picture. There isn't any option that I can find to simply disable the built-in display entirely and run the external LCD at its native resolution. I am aware of closed lid mode, but the MBP was disassembled while in storage for about 6 months (took it apart to pull the HDD) and the cable to the touchpad, which controls the sleep sensor was damaged, meaning closed lid mode won't work. I've looked into replacing the cable, but the cheapest I've been able to find it is $75-100, and I'm trying not to invest any more money into this computer as it also has a completely dead battery and a few other minor problems. I've found the app SwitchResX which appears to allow you to do what I need, but it has a lot of functionality I don't need and a ~$20 registration charge attached to it. An odd set of circumstances, I'm aware, but I was hoping somebody might know of an OS hack that would let me just disable the internal display and be done with it. :)

  Read the article

• Fixing a corrupted Windows Server 2003 server

  - by Keith

  I have a Windows Server 2003 server that is being mainly used for some reporting done in SQL Server. Recently Windows has started complaining about being corrupted, we are getting an NTFS error 55: The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume \Device\HarddiskVolume1. The server is RAID 5 and I did have a disk die however the RAID never went degraded since I have a hotspare. I replaced the hot spare and I'm still having problems. When I run chkdsk I get tons of messages.. some are: Deleting corrupted attribute record (128, "") from file record segment 194746 Those go on for a while. Then it deletes some orphan files. Then it does Correcting error in index $I30 for file 132426 And that goes on for a while. Then I get tons of Recovering orphaned file RE1AB6~1.LOG into directory file 534959 I have seen a lot of errors relating to the SQL Server reporting services. What are my options at this point? I would prefer to fix the issue instead of building a new server but I don't know if I can at this point.

  Read the article

• Apache, logerror and logrotate: what is the best method?

  - by OlivierDofus

  Hi! Here's a vhost example of my sites: <VirtualHost *:80> DocumentRoot /datas/web/woog ServerName woog.com ServerAlias www.woog.com ErrorLog "|/httpd-2.2.8/bin/rotatelogs /logs/woog/error_log 86400" CustomLog "|/httpd-2.2.8/bin/rotatelogs /logs/woog/access_log 86400" combined DirectoryIndex index.php index.htm <Location /> Allow from All </Location> <Directory /*> Options FollowSymLinks AllowOverride Limit AuthConfig </Directory> </VirtualHost> I've got 12 sites running now. This gives something like: [Shake]:/sources/software/mod_log_rotate# ps x | grep rotate /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/error_log 86400 /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/error_log 86400 [snap (as many error_log as virtual hosts)] /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/access_log 86400 /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/access_log 86400 [snap (as many access_log as virtual hosts)] grep rotate [Shake]:/sources/software/mod_log_rotate# !!! I've been looking everywhere but I've only found mod_log_rotate. The "little" problem is that the author (very good C developper) explains: "Unfortunately Apache error logs are handled in such a way that we can't work the same log rotation magic on them. Like transfer logs they support piped logging though so you can still use rotatelogs for them. " So my question is: what would be the best way to handle multiple logs? If I just do a very classical log and I use the system's "logrotate" program couldn't this be a good deal? How would/do you deal with that? Thank you!

  Read the article

< Previous Page | 586 587 588 589 590 591 592 593 594 595 596 597  | Next Page >