Search Results

Search found 17749 results on 710 pages for 'connection pool'.

Page 593/710 | < Previous Page | 589 590 591 592 593 594 595 596 597 598 599 600  | Next Page >

  • Getting 502 instead of 503 when all backend servers are down running HAProxy behind Apache

    - by scarba05
    I'm testing running HAProxy as a dedicated load balancer behind Apache 2.2, replacing our current configuration where we use Apache's load balancer. In our current, Apache only, set-up if all the backend (origin) servers are down Apache will serve a 503 service unavailable message. With HAProxy I get a 502 bad gateway response. I'm using a simple reverse proxy rewrite rule in Apache RewriteRule ^/(.*) http://127.0.0.1:8000/$1 [last,proxy] In HAProxy I have the following (running in default tcp mode) defaults log global option tcp-smart-accept timeout connect 7s timeout client 60s timeout queue 120s timeout server 60s listen my_server 127.0.0.1:8000 balance leastconn server backend1 127.0.0.1:8001 check observe layer4 maxconn 2 server backend1 127.0.0.1:8001 check observe layer4 maxconn 2 Testing connecting directly to the load balancer when the backend servers are down: [root@dev ~]# wget http://127.0.0.1:8000/ test.html --2012-05-28 11:45:28-- http://127.0.0.1:8000/ Connecting to 127.0.0.1:8000... connected. HTTP request sent, awaiting response... No data received. So presumably this is down to the fact that HAProxy accepts the connection and then closes it.

    Read the article

  • Windows Virtual Machines will not run

    - by jlego
    I'm trying to setup a few virtual machines to use for testing websites in the various old versions of IE. I had Microsoft Virtual PC working on an older machine using XP mode and 2 other VHD's from Microsoft that allowed me to test in IE6-IE8. I've recently gotten a new work machine and am trying to set up the VMs again for testing, however nothing seems to be working. Both the old and the new system run Windows 7 64-bit Ultimate with AMD processors. I downloaded Virtual PC & XP mode from here http://www.microsoft.com/windows/virtual-pc/download.aspx and go through the installation process. XP mode is installed, but when I try to run it it goes through the initial setup process only to fail when it is almost complete with the error "Cannot Complete Setup". (After googling I see that this might be a conflict with my processor) I download other VHD's from here http://www.microsoft.com/windows/virtual-pc/download.aspx in order to get the other versions of IE and try to set those up in Virtual PC as well. I click on them to start the machine and both Windows 7 with IE8 and Windows Vista with IE7 just hang at a black screen. I try to use Virtual Box instead, and I get Windows XP with IE6 running, but I have no internet connection in the VM. I try all different settings and try to google the correct settings but nothing seems to work. When I load the VM, XP shows that its found new hardware but it needs the drivers. One of these pieces of hardware is the network adapter, but I can't connect to the internet to download the driver in the guest OS. VirtualBox tells me I need to install extensions in order for things to function properly. I go through the installation process in the guest OS and restart the VM, however now XP is asking for validation and I can't access the VM. I try installing the other 2 OS (Vista & 7) but I get a BSOD right after the startup screen appears and the VM restarts itself. I'm getting so frustrated trying to make this work, I would really appreciate any assistance on getting the VMs up and running or any alternatives for testing websites in Internet Explorer.

    Read the article

  • Route all traffic via OpenVPN client

    - by Ilya
    I've got OpenVPN client running on 192.168.0.3. What I'd like to do is route all the traffic from the second computer with 192.168.0.100 via OpenVPN client that's running on the first computer. My router ip is 192.168.0.1 Network topology: Windows computer with OpenVPN client: 192.168.0.3 Windows computer whose traffic has to be rerouted: 192.168.0.100 Router: 192.168.0.1 I want it to work in the following way: 192.168.0.100 computer => 192.168.0.3 computer => OpenVPN => 192.168.0.1 How can I achieve that by only modifying windows' routing table? I've tried entering the following into windows shell(on computer without VPN), which didn't work (it just dropped my internet connection): route delete 0.0.0.0 mask 255.255.255.255 192.168.0.1 route add 0.0.0.0 mask 255.255.255.255 192.168.0.3 Should I also setup the computer that has OpenVPN client running? Does it have anything to do with windows tcp forwarding? Thanks!

    Read the article

  • VNC authentication failure

    - by cf16
    I try to connect to my vncserver running on CentOs from home computer, behind firewall. I have installed Win7 and Ubuntu both on this machine. I have an error: VNC conenction failed: vncserver too many security failures even when loging with right credentials (I reset passwd on CentOs) I get: authentication failure. I observe that I have to wait a whole day to be able to relogin at all. Is it something regarding that I try as root? I think important is also that I have to login to remote Centos through port 6050 - none else port works for me. Do I have to do something with other ports? I see that vncserver is listening on 5901, 5902 if another added - and I consider connection is established because from time to time (long time) the passwd prompt appears,... right? I have created additional user1, password for him to CentOS and to VNC, also user2. I do: service vncserver start and two servers starts, one :1, and second on :2. When I try to connect to vncserverIP:1 I get what described above, but when I try connect to vncserverIP:2 it says that the trial was unsuccessful. please help, what to do? additionally: how to disable this lockout for a testing purposes?

    Read the article

  • postgresql deleteing old records from log tables

    - by Max
    I have a postgresql database which stores my radius connection information. What I want to do is only store a months worth of logs. How would I craft a sql statement that I can run from cron that would go and delete and rows that where older then a month? Format of the date in the table. that date is taken from acctstoptime collum Date format 2010-01-27 16:02:17-05 Format of the table in question. -- Table: radacct CREATE TABLE radacct ( radacctid bigserial NOT NULL, acctsessionid character varying(32) NOT NULL, acctuniqueid character varying(32) NOT NULL, username character varying(253), groupname character varying(253), realm character varying(64), nasipaddress inet NOT NULL, nasportid character varying(15), nasporttype character varying(32), acctstarttime timestamp with time zone, acctstoptime timestamp with time zone, acctsessiontime bigint, acctauthentic character varying(32), connectinfo_start character varying(50), connectinfo_stop character varying(50), acctinputoctets bigint, acctoutputoctets bigint, calledstationid character varying(50), callingstationid character varying(50), acctterminatecause character varying(32), servicetype character varying(32), xascendsessionsvrkey character varying(10), framedprotocol character varying(32), framedipaddress inet, acctstartdelay integer, acctstopdelay integer, freesidestatus character varying(32), CONSTRAINT radacct_pkey PRIMARY KEY (radacctid) ) WITH (OIDS=FALSE); ALTER TABLE radacct OWNER TO radius; -- Index: freesidestatus CREATE INDEX freesidestatus ON radacct USING btree (freesidestatus); -- Index: radacct_active_user_idx CREATE INDEX radacct_active_user_idx ON radacct USING btree (username, nasipaddress, acctsessionid) WHERE acctstoptime IS NULL; -- Index: radacct_start_user_idx CREATE INDEX radacct_start_user_idx ON radacct USING btree (acctstarttime, username);

    Read the article

  • subdomain .htaccess redirection via ssh remote port forwarding

    - by Achim
    I ask you to help me URL redirecting a subdomain to a SSH remote forwarded port: The current setup is the following: The server A have a local webserver running on port 80. This server is connected to a DSL line or a GPRS connection where the IP address changes often. To prevent a DynDNS setup we established a SSH remote port forwarding to a server B with a static IP adress. This is done on server A by the following statement: ssh -N -p 80 -g -R 10000:localhost:80 tunneling@<Server B IP> So by accessing the new port 10000 of the servers B IP-adress, all traffic is forwarded to the server A port 80 - this works fine! But to offer a more comfortable url to the user I want to hide the server B IP-adress and offer a subdomain. My domain provider allows to add subdomains and redirections to some other servers. In general, this works, I've tested this with different servers. But it don't work if the destination is the port forwarded port of server B. The initial redirection is done, the request is send to server A and the response are forwarded to server B and shown in the browser - fine. But then the URL within the browser is switched away from the subdomain to the IP:port of server B. So the user don't see the subdomain in the URL string of the browser anymore. I've tried this with my providers subdomain redirection, as well as .htaccess redirect, as well as META refresh, the problem always persist. Is there a parameter in the ssh reverse forwarding setup (I guess this is the place where the fix have to be) to keep the typed in subdomain URL and not show the IP. Thanks Achim

    Read the article

  • eXist-db: can't start webstart client on a closed port, reverse proxied via apache

    - by rvdb
    I am configuring an Apache HTTP server so it reverse proxies requests starting with /app/ to an eXist-db instance running in a Tomcat server, on port 8082. This port has been closed in the firewall and is inaccessible to the outer world. Following the eXist documentation, I have following rules in place in my httpd.conf file: ProxyPass /apps/ http://localhost:8082/ ProxyPassReverse /apps/ http://localhost:8082/ ProxyPassReverseCookiePath /apps/ / All goes well for requests to e.g. 'http://mydomain/apps/exist/index.xml'. Yet, the webstart client (accessible at 'http://localhost:8082/exist/webstart/exist.jnlp' on the web server) doesn't work behind the proxy. While 'http://mydomain/apps/exist/webstart/exist.jnlp' does generate a valid exist.jnlp file, that file can't be executed. The reason seems quite obvious: apparently, the eXist-db instance generating the exist.jnlp file only sees the proxied request as: 'http://localhost:8082/exist/webstart/exist.jnlp'. Yet, since the exist.jnlp file is executed on the client, that reference is meaningless (unless the client computer happens to have an eXist-db instance running on that port). Executing the exist.jnlp file hence fails with a 'connection refused' error. Yet, there's no problem at all connecting a local eXist-db Java client to the proxied eXist instance with the URL xmldb:exist://mydomain/apps/exist/xmlrpc. The problem lies in generating the webstart exist.jnlp file, which seems to need access to a publicly accessible URL. However, opening port 8082 and replacing the Proxy references to 'http://localhost:8082' with 'http://mydomain:8082' IMO rather destroys the point of reverse proxying. Do others have had success reverse proxying eXist-db on a closed port behind Apache? Are there perhaps some Proxy configuration settings I have overlooked (I'm no expert at all) that can make eXist see the original request instead of the proxied one? Kind regards, Ron

    Read the article

  • Need to boot into chkdsk from USB on Windows netbook

    - by Gaz Davidson
    While attempting to install Ubuntu on a 32-bit Windows XP netbook, the partition resize operation failed due to inconsistencies in the NTFS filesystem (lesson learned: run chkdsk /f in Windows before trying to resize a partition in Linux). Now the installer only gives the option to replace Windows with Ubuntu, the partition can't be resized in gparted, which displays a red exclamation mark and an error log when you click it. To make matters worse, we're also unable to reboot into Windows to get at chkdsk. We get a BSoD when choosing any of the options (including the DOS recovery console thing). The netbook has no CD-ROM drive, contains no recovery image and our only connection to the Internet is via the hotspot on my mobile device. We don't have Windows recovery CDs, but we do have a USB flash drive. We have a 64-bit laptop running Ubuntu 12.04 and Windows 7 (both 64-bit). So, on to the question: Is anyone aware of a way to get into a DOS recovery console and run chkdsk from a USB disk drive, without having to pirate Windows XP or download hundreds and hundreds of megabytes of crap? If it was my device I'd just flatten it, but it isn't. Please help!

    Read the article

  • Binding to LDAPS using PHP failing

    - by Sean
    We've finally set-up our server to accept ldap SSL connections thanks to another question answered by a helpful member. Our problem now is that when attempting to bind to ldap using the below simple PHP script, we constantly fail. Binding using ldap instead of ldaps works just fine using the script so I know the ldap is enabled. The catcher is that while using LDP.exe, we can successfully connect and bind to ldap on port 636 using a secure connection. The script we are failing with is below: <?php $ldap = ldap_connect("ldaps://localhost"); $username="user"; $password="pass"; if($bind = ldap_bind($ldap, $username,$password )) echo "logged in"; else echo "fail"; echo "<br/>done"; ?> We've also attempted inputting the username as "user@domain" or "domain/user" with no success. It seems I'm forever having LDAP/Cert questions. Our environment is Server 2008.

    Read the article

  • OpenVPN, install a TAP adapter

    - by GolezTrol
    When I try to connect to my work VPN using OpenVPN, the connection fails with the message: All TAP-Win32 adapters on this system are currently in use. Many sources suggest to look in Control Panel\Network and Internet\Network Connections an enable the TAP adapter, but when I look there, there is none. Now I've run addtap.bat which is provided with OpenVPN, but I still don't get to see any TAP adapter, and logging in in VPN still fails. The output of addtap.bat is C:\Windows\system32>"C:\Program Files (x86)\OpenVPN\bin\tapinstall.exe" install "C:\Program Files (x86)\OpenVPN\driver\OemWin2k.inf" tap0801 Device node created. Install is complete when drivers are updated... Updating drivers for tap0801 from C:\Program Files (x86)\OpenVPN\driver\OemWin2k .inf. Drivers updated successfully. I've Run As Administrator both the setup of OpenVPN and addtap.bat. I've run deltapall.bat to remove any (maybe hidden) adapters. It said it removed three of them, after which I ran addtap.bat again to try to create another one. I also run OpenVPN itself as administrator. What's wrong? Running Windows 7 Home Premium on a HP Pavilion dv7 4050ed. It has worked before, but I recently had to reinstall my laptop, for which I used the restore disks I created when I just got it. Everything else seems to work fine. == UPDATE == The TAP adapter is found in Device Manager, but apparently it is disabled because it is incompatible with Windows 7 64bit. I've deïnstalled OpenVPNGui, downloaded a version that should be 64bit compatible, and installed that. Still no cigar. Then I found a tip to install OpenVPN (version 9) after installing OpenVPNGui, because that installs OpenVPN version 8. Now I got a v9 TAP driver in Device Manager, but it still doesn't work and shows up in device manager with an exclamation mark, and not at all in my network devices.

    Read the article

  • How to get a new-pssession in PowerShell to talk to my ICS-connected laptop for Remoting

    - by Scott Bilas
    If I have my laptop on the LAN, then Powershell remoting works fine from my workstation to the laptop. However, the LAN is wireless, and so sometimes I will connect on a wire to my workstation. It has two ethernet ports so I have the secondary wired up to share to the laptop using Win7's Internet Connection Sharing. (Btw I know that avoiding ICS would solve the problem, but that's not an option right now.) So my question is: what magic registry bits or command line options do I need to flip to get remoting to work to my laptop through ICS? Here's what happens when I try it: new-pssession -computername 192.168.137.161 [192.168.137.161] Connecting to remote server failed with the following error message : The WinRM client cannot process the request. Default authentication may be used with an IP address under the following conditions: the transport is HTTPS or the destination is in the TrustedHosts list, and explicit credentials are provided. Use winrm.cmd to configure TrustedHosts. Note that computers in the TrustedHosts list might not be authenticated. For more information on how to set TrustedHosts run the following command: winrm help config. For more information, see the about_Remote_Troubleshooting Help topic. + CategoryInfo : OpenError: (System.Manageme....RemoteRunspace:RemoteRunspace) [], PSRemotingTransportException + FullyQualifiedErrorId : PSSessionOpenFailed I'm having a hard time understanding the documentation for PowerShell and WinRM. I've tried messing with allowing ports in the firewall and setting TrustedHosts to * on my workstation (don't think this is a good idea on the laptop). I have no idea where to go from here, would appreciate any help.

    Read the article

  • How do I resolve certificate errors on HP blade center

    - by Martin Hilton
    I'm trying to sort out the ssl certificate errors that we get when trying to manage our HP c7000 blade enclosures. To that end I have created a signing certificate and imported it into the browser. In Onboard Administrator I created a certificate signing request, which I signed with my CA and then uploaded the certificate. This worked perfectly, and I no longer get any SSL errors when connection to Onboard Administrator. The problem comes when trying to connect through Onboard Administrator to the iLo on the blades themselves. Done by clicking on the "Web Administration" link. Onboard Administrator links to the blade with it's IP address rather than host name. But the certificate signing request that iLo creates uses the host name. Even when this certificate is signed the browser still complains it is for the wrong domain. I either need to be able to get Onboard Administrator to connect to the blades using host name rather than IP address, or get a certificate signing request which contains the IP address as the CN rather than the host name. It doesn't particularly matter which. Does anybody know how to configure this?

    Read the article

  • Why do I often have to refresh pages I navigate to once for them (or content in them) to load?

    - by GetOutOfBox
    I have noticed a bizarre pattern when using my PC, that when I open a link to a website, it often will often take a very long time to load, or time out. Sometimes content on the website will be drawn, but again, it seems to get "stuck" for an unusual amount of time before finishing. Most affected is Youtube; almost every time I navigate to a youtube video from another website such as Google, the video will not begin playing, but will instead just display the player controls with a black screen where the video should be and the buffering symbol, usually before displaying an error such as "The video failed to load". The unusual part of this problem is that whenever this happens, refreshing the page always causes it to load almost immediately the second time around, without any problems. Note that I'm not talking about how some browsers will dump whatever has been cached to the "pallet" briefly when the page is refreshed or loading stopped; but that the second time loading the website being faster. I have done my best to rule out some of the obvious causes: My Windows 7 desktop computer is the only device that seems to be affected. I use Firefox on it (latest version, flash updated, etc). My connection has more than enough bandwidth (30 megabits down, 4 up), and I've even tried QoSing all other devices to make sure this isn't happening due to usage spikes. Wireshark is not showing any clearly unusual network activity (i.e frequently dropped packets).

    Read the article

  • CentOS 5.5 remote kickstart installation stalls at "Starting install process." How to debug?

    - by ewwhite
    Hello, I'm having a difficult time with a remote CentOS 5.5 kickstart installation on an HP ProLiant DL360 G6. This is in an environment where I maintain an internal CentOS yum repository. The kickstart installation and post scripts have been tested and normally work. This hardware is also common in this environment, so I do not believe that it is a factor. Unfortunately, I'm having problems with a specific server install. The system is remote to the yum repository at a distance of 500 miles. They are connected over a private low-latency 100-megabit layer 2 connection (26ms round-trip). I'm mounting the 10mb CentOS 5 netinstall ISO image via an HP ILO remote console. The initial boot parameters are: linux ks=http://yum.abctrading.com/prop.cfg ksdevice=eth0 ip=x.x.x.x dns=x.x.x.x netmask=255.255.255.0 gateway=x.x.x.x I'm using the url --url http://ks.abctrading.com/5.5/os/x86_64/ method of installation. This quickly boots into the anaconda installer, pulls the kickstart config and formats the drives. The process eventually halts at the screen below, reading "Starting install process.". Going to the other virtual consoles give the second image below. The process stalls at this point and cannot proceed with the rest of the installation. Running the same kickstart config locally works just fine. I've tried mounting the boot ISO from the console as well as from the ILO2 command line pointing to a locally-hosted boot ISO via http. How can I debug this? Are there any options I've overlooked?

    Read the article

  • How to get multipath working for Ubuntu Server 12.04

    - by mlampi
    I'm working on a project which aims to make use of Ubuntu servers running on enterprise class hardware. In our case that means IBM HS23E blade servers, QLogic 4GB fibre channel extension cards and quite old IBM DS4500 disk array with two controllers. At the moment we have fibre channel as only boot option and Ubuntu Server 12.04 installed just fine and is able to boot without multipath. I'm not a linux professional myself but in our team we have people who will understand the technical stuff. Don't let my post confuse :) The current situation is that we have only one fibre channel connection to a single disk array controller. Real life case would be of course quite different. At minimum we should have two fibre channel ports connected to two different switches and two different controllers. However, we have no idea how to set up multipath tool. Is the DM-MPIO the right software? At minimum we should be able to boot when multiple connections are available and achieve fault tolerance when any of them should be down. Since the disk array is not the latest hardware, I managed to find RDAC driver sources only for 2.6.x kernel. And we have 3.2.x. Another issue is to build a multipath.conf. The said driver sources are from IBM support and the QLogic drivers provided to Ubuntu installer are from Ubuntu site. It seems that RHEL and SLES would have near out of the box support but that is not an option for our project. Actual questions: - What is the recommended software tool for multipath for Ubuntu Server 12.04? - Is there available pre-made configurations or templates? Does it require disk array / controller specific settings or do a more generic config work? - Do you have expriences on similar setup and like to share the knowledge? I'll provide you with any additional information you might require. Thanks in advance.

    Read the article

  • Spammer relaying via Postfix mail server

    - by Paddington
    I have a Plesk 9.5 mail server (cm.snowbarre.co.za) on Ubuntu 8.04 LTS which forwards all SMTP traffic to an anti-spam server cacti.snowbarre.co.za. Many times I see the headers on the anti-spam server to contain from addresses not hosted on the mail server and I have checked and confirmed that my server is not an open relay server. How can a spammer be using my server to relay spam traffic? How can I stop this? Open relay test: paddington@paddington-MS-7387:~$ telnet cm 25 Trying 196.201.x.x... Connected to cm. Escape character is '^]'. 220 cm.snowbarre.co.za ESMTP Postfix (Ubuntu) mail from:[email protected] 250 2.1.0 Ok rcpt:[email protected] 221 2.7.0 Error: I can break rules, too. Goodbye. Connection closed by foreign host. paddington@paddington-MS-7387:~$ A typical headers is: *Received from cm.snowbarre.co.za (cm.snowbarre.co.za[196.201.x.x]) by cacti.snowbarre.co.za (Postfix) with ESMTPS id 00B601881AD; Mon, 27 Aug 2012 14:03:29 +0200 (SAST) Received from cm.snowbarre.co.za (localhost [127.0.0.1]) by cm.snowbarre.co.za (Postfix) with ESMTP id 81627367E007; Mon, 27 Aug 2012 14:02:50 +0200 (SAST) Received from User (ml82.128.x.x.multilinksg.com [82.128.x.x]) by cm.snowbarre.co.za (Postfix) with ESMTP; Mon, 27 Aug 2012 14:02:49 +0200 (SAST) Reply-To <[email protected]> From "Ms Nkeuri Aguiyi"<[email protected]> Subject Your Unpaid Fund. Date Mon, 27 Aug 2012 05:03:22 -0700 MIME-Version 1.0 Content-Type text/html; charset="Windows-1251" Content-Transfer-Encoding 7bit X-Priority 3 X-MSMail-Priority Normal X-Mailer Microsoft Outlook Express 6.00.2600.0000 X-MimeOLE Produced By Microsoft MimeOLE V6.00.2600.0000 X-Antivirus avast! (VPS 120821-0, 08/21/2012), Outbound message X-Antivirus-Status Clean Message-Id <[email protected]> To undisclosed-recipients:;*

    Read the article

  • NX Client for Windows 7 Opens Remote Desktop in Multiple Windows

    - by Corey Kennedy
    What I'm trying to do: access my Ubuntu desktop remotely via NX Client on my Windows 7 laptop. My environment: server: Ubuntu 10.10 on AMD 1Ghz/512MB RAM PC client: Windows 7 on ThinkPad sl510 Software: server is running NXServer 3.4.0. Using xfce4 window manager. Laptop is using NXClient for Windows In my NX Client "Desktop" settings I've selected "Unix" and "Custom" for OS and environment. I've also specified "startxfce4" as the application to launch when NX connects. I am able to authenticate an NX session on my laptop. By this I mean, I can start the client on my laptop, enter credentials for my Linux user, and NX establishes a connection to the server and attempts to open a remote desktop window. The problem, though, is that this remote desktop is "fragmented" into many Windows. One window will display the bulk of my desktop (complete with desktop icons for "Home," "File System," and "Trash") while another window will contain the taskbar, and another window will contain the application strip. I can select each of these Windows individually, but I cannot click on any objects within them. I've searched Super User, Ubuntu Forums, NX help, Server Fault, and tried many Google searches - none have turned up another case of this particular problem. I'm stumped. Does anyone have any suggestions for what I might try? I'm guessing the problem has to do with my xfce config files, but I've only just setup this server - it's been a long time since I've used Linux and there's a lot I just don't know. What I am NOT trying to do: use Desktop sharing from Ubuntu, whereby I VNC into a desktop that I've already established on the server. I am trying to configure this Linux box as a headless server that I can stash someplace out-of-the-way in my house, then interact with through my laptop. I don't want to have a monitor or keyboard connected to the Linux box. Thanks for your help!

    Read the article

  • SQL Server 2008 second instance times out when logging in -- but only the first time?

    - by Kromey
    This is a strange one that has plagued me for a while now. When logging in to the second instance of SQL Server 2008 on one of our database servers, we get a timeout error: Cannot connect to servername\mssqlserver2. Additional information: Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. (Microsoft SQL Server)") (This is the error message when trying to connect with Microsoft SQL Server Management Studio; other tools experience the same error, but of course say it in different ways.) Immediately re-attempting to log in works just fine, so whatever the cause it's ephemeral! This happens regardless of user or authentication type (both Windows and SQL Server authentication methods are supported on this instance). What's even weirder, though, is that the first instance on this server has never once demonstrated this problem. Server is a Windows Server 2008 R2 virtual server, hosted in Microsoft Hyper-V (host is likewise Server 2008 R2). The server has 2GB of RAM, and seems to regularly be using 90% of that -- could low memory be the cause of this issue? I could see this second instance -- which is not used very often yet -- being swapped out to disk, and then taking too long to load back into memory to respond in time to the connection request, but I'd rather have more than just my own hunch before I go scheduling a downtime for this server (the first instance is used regularly) and then just throwing extra resources at it in the blind hope that the problem goes away.

    Read the article

  • Exchange 2010 remove Arbitration mailbox and mailbox store db

    - by JNM
    I have a problem with Exchange 2010 which is a nightmare for me. The problem is, that in Exchange management console i have several store databases in database management tab. only one is mounted, because i am using it. the second one is mounted, but it was used on other server before (now that server is dead). that database mounted status is UNKNOWN. The file of that database does not exist, but it still shows there. I can't remove it from management console, because it has mailboxes. i removed all mailboxes and disabled two arbitrary mailboxes. i can't delete it because i still have one arbitrary mailbox left. i can't move it, because it requires connection to dead server. i can't disable it, because i get error that it is the last one in organization. Can somebody help me? Solved it by using this command: Get-Mailbox -Arbitration -Database db1 | Remove-Mailbox -Arbitration -RemoveLastArbitrationMailboxAllowed Now i have another problem. Exchange management console shows public folder from different server which is dead now. That folder was copied here, but it is not needed anymore. Public folder file has been deleted, and records from ADSI edit has been removed too. But i can't remove that folder from management console. i get an error Exchange isn't able to check for public folder replicas for "My Public Folder Database". Anybody can help me with that?

    Read the article

  • BackupPC - why does it use rsync --sender --server ... ?

    - by Jakobud
    I'm in the process of experimenting with BackupPC on a CentOS 5.5 server. I have everything pretty much setup with default values. I tried setting up a basic backup for a host's /www directory. The backup fails with the following errors: full backup started for directory /www Running: /usr/bin/ssh -q -x -l root target /usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/ Xfer PIDs are now 30395 Read EOF: Connection reset by peer Tried again: got 0 bytes Done: 0 files, 0 bytes Got fatal error during xfer (Unable to read 4 bytes) Backup aborted (Unable to read 4 bytes) Not saving this as a partial backup since it has fewer files than the prior one (got 0 and 0 files versus 0) First of all, yes I have my ssh keys setup to allow me to ssh to the target server without requiring a password. In the process of troubleshooting, I tried the above ssh command directly from the command line, and it hangs. Looking at the end of the debug messages for SSH I get: debug1: Sending subsystem: /usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/ Request for subsystem '/usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/' failed on channel 0 Next I started looking at the rsync flags. I did not recognize --server and --sender. Looking at the rsync man pages, sure enough, I don't see anything about --server or --sender in there. What are those in there for? Looking at the BackupPC config I have this: RsyncClientPath = /usr/bin/rsync RsyncClientCmd = $sshPath -q -x -l root $host $rsyncPath $argList+ And for the arguments, I have the following listed: --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive Notice there is no --server, --sender or --ignore-times. Why are these things getting added in? Is this part of the problem?

    Read the article

  • network policy + WPA enterprise (tkip) Windows 2008 R2

    - by Aceth
    hi I've attempted the following guide and in a bit of a pickle. http://techblog.mirabito.net.au/?p=87 My main goal is to have a username / password based wireless authentication with active directory integration. I keep getting the error Network Policy Server denied access to a user. Contact the Network Policy Server administrator for more information. User: Security ID: domain\rhysbeta Account Name: rhysbeta Account Domain: domain Fully Qualified Account Name: domain\rhysbeta Client Machine: Security ID: NULL SID Account Name: - Fully Qualified Account Name: - OS-Version: - Called Station Identifier: 00-12-BF-00-71-3C:wirelessname Calling Station Identifier: 00-23-76-5D-1E-31 NAS: NAS IPv4 Address: 0.0.0.0 NAS IPv6 Address: - NAS Identifier: - NAS Port-Type: Wireless - IEEE 802.11 NAS Port: 2 RADIUS Client: Client Friendly Name: Belkin54g Client IP Address: x.x.x.10 Authentication Details: Connection Request Policy Name: Secure Wireless Connections Network Policy Name: Secure Wireless Connections Authentication Provider: Windows Authentication Server: srvr.example.com Authentication Type: EAP EAP Type: - Account Session Identifier: - Logging Results: Accounting information was written to the local log file. Reason Code: 22 Reason: The client could not be authenticated because the Extensible Authentication Protocol (EAP) Type cannot be processed by the server. ` I would love to have it so that non domain devices

    Read the article

  • Do all routers really must know all routes to every router?

    - by Philipili
    This is my complicated and long question. First let's talk about the context. Network topology: PC A --- RT A --- RT C --- RT B --- PC B (RT C has a WAN NIC connected to "the cloud") With this situation : PC A must send a packet to PC B Default routes direct packets to the cloud We haven't access to RT C's configuration RT C only knows how to join network A, not network B RT A knows about network B RT B knows about network A RT C's routing table: Destination NIC Gateway 0.0.0.0 WAN Cloud Network A LAN A RT A's WAN RT A's routing table: Destination NIC Gateway 0.0.0.0 WAN LAN A Network B WAN LAN A RT B's routing table: Destination NIC Gateway 0.0.0.0 WAN LAN B Network A WAN LAN B I would like to permit PC A and PC B to communicate, but I don't have access to RT C. Networks B and BC are new. Can PC A send a packet to RT B's WAN NIC (which is possible) and "ask RT B to direct the packet to PC B" ? I believe replacing RT B with a VPN server should do the trick, but I would like to know if it is possible to make it without establishing a new connection.

    Read the article

  • Apache2 Segmentation fault with wsgi_module

    - by a coder
    Apache 2.2.3 is running as an existing web server under RHEL 5. Attempting to set up Trac using wsgi_module. RHEL 5 ships with python 2.4, so in order to use the current version of Trac (1.0) I needed to install it with easy_install-2.6. Trac works with the default mod_python, however users strongly encourage not using this module as it is officially dead. Using RHEL's package manager, I downloaded/installed python26-mod_wsgi.so. I backed up the httpd.conf, then made the following additions: LoadModule wsgi_module modules/python26-mod_wsgi.so #...# WSGIScriptAlias /trac /www/virtualhosts/trac/deploy/cgi-bin/trac.wsgi <Directory /www/virtualhosts/trac/deploy/cgi-bin> WSGIApplicationGroup %{GLOBAL} Order deny,allow Allow from all </Directory> Next I moved trac.conf to trac.conf.bak (contains mod_python calls). I tested the configuration using: apachectl configtest Syntax is OK. So I reloaded the server config using: service httpd reload At this time, all virtualhosted sites stopped responding. I restored my backup copy of httpd.conf, reloaded the server config, and the virtualhosted sites are being served again. A quick look at the httpd error_log shows: [Mon Oct 08 10:20:04 2012] [info] mod_wsgi (pid=28282): Initializing Python. [Mon Oct 08 10:20:04 2012] [info] mod_wsgi (pid=28280): Attach interpreter ''. [Mon Oct 08 10:20:04 2012] [debug] proxy_util.c(1817): proxy: grabbed scoreboard slot 0 in child 28283 for worker proxy:reverse [Mon Oct 08 10:20:04 2012] [debug] proxy_util.c(1836): proxy: worker proxy:reverse already initialized [Mon Oct 08 10:20:04 2012] [debug] proxy_util.c(1930): proxy: initialized single connection worker 0 in child 28283 for (*) [Mon Oct 08 10:20:04 2012] [info] mod_wsgi (pid=28283): Initializing Python. [Mon Oct 08 10:20:04 2012] [notice] child pid 28249 exit signal Segmentation fault (11) [Mon Oct 08 10:20:04 2012] [notice] child pid 28250 exit signal Segmentation fault (11) [Mon Oct 08 10:20:04 2012] [notice] child pid 28251 exit signal Segmentation fault (11) There are many similar lines, this is just a snip of the log file. Suggestions on what could be going on to cause the Segmentation faults?

    Read the article

  • Windows Explorer slow to open networked computer, fast to navigate once opened

    - by Scott Noyes
    I open Windows Explorer and enter an IP for a computer on my home network (\\192.168.1.101). It takes 30 seconds or more to present a list of the shared folders. It does not appear to be an initial handshaking/authentication thing; even if I allow the view to load and then immediately load the same again, it is always slow. Once they appear, navigating through folders and opening files is fast. Also, navigating directly to a folder (\\192.168.1.101\My Music) is fast, even if it's the first connection since a restart. Using \\computerName instead of the IP address gives exactly the same results. Pings return in 1ms. net view \\computerName (or \ipAddress) returns the list of shared folders fast. This makes me suspect an Explorer issue rather than a network issue. Suspecting that the remote computer was being automatically indexed or something, I went into Tools-Folder Options-View and unchecked "Automatically search for network folders and printers," but that made no difference. De-selecting the "Folders" icon near the address bar makes no difference. Adding the IP address and computer name to the hosts file makes no difference. Both computers involved are laptops running Windows XP. Both have WiFi and cable adapters. Mine is not connected via cable. The result is the same whether the target is plugged in to the cable or not (although the IP address changes - 192.168.1.101 over cable, 192.168.1.103 over WiFi.) We are using DHCP assigned by the router.

    Read the article

  • What command should be used to connect via SSH through squid proxy?

    - by Raul Cardoso
    I have set up a Squid HTTP Proxy (in centOS) and intended to use it also for ssh connections. Managed to configure putty (in a windows client) to use this proxy while connecting by ssh. Confirmed in the "target host" that the ssh connection was coming from Proxy server ip instead of the windows client IP. Used: targethost: 22 for ssh proxyserv: 3128 for proxy (along with proxy credentials) I'm now having problems connecting to the "target host" using Ubuntu and the same proxy server. I have tried the following: me@mycomp:~$ connect-proxy -H test@proxyserv:3128 targethost 22 Enter proxy authentication password for test@proxyserv: SSH-2.0-OpenSSH_6.2p2 Ubuntu-6 It hangs in last line, expecting some input. All attempts resulted in a "Protocol mismatch." error. Putty successfully connects to the http proxy and sends credentials, showing me ssh login right away. - How to do (with commands in Ubuntu) the same putty does? - Is there any other way than connect-proxy command to do this? Edit: Also tried the following with same result ("Protocol mismatch") me@mycomp:~$ connect-proxy -H test@proxyserv:3128 targethost 22 ssh -l myshel_login Thanks in advance Edit: Solution details (thanks to NickW pointing the right way) installed corkscrew and added to ssh_config Host targethost ProxyCommand corkscrew proxyserv 3128 %h %p /etc/ssh/proxypass created proxypass file login:password Restarted ssh and used a simple ssh command ssh mylogin@targethost (ssh password was asked as usual)

    Read the article

< Previous Page | 589 590 591 592 593 594 595 596 597 598 599 600  | Next Page >