Search Results

Search found 18648 results on 746 pages for 'left join'.

Page 594/746 | < Previous Page | 590 591 592 593 594 595 596 597 598 599 600 601  | Next Page >

• New to building computers worried about temps

  - by dave

  I'm new to building my own computers and I was wondering about maximum temperatures. I understand that the room temp can affect the computers temp but how relevent is it? I understand that if my room temp is 20°C none of my computer parts could be lower than that. But if my room is 27°C instead of 20°C would this cause my computers parts to heat up more/faster? My new computer I built myself for gaming is i7 2600k 16gb ram ddr3 1600 hd6970 2 gb 240gb ssd ( bought a nas with 3 2tb drives in raid 5 for my home network ) 850w modular psu I also have my old hp computer i3 2120 8gb ram hd6770 1tb hdd I also have 3 laptops in my household, but I am not worried about their temps, they heat up my legs but they are never under stress. Due to size and money reasons I used an old case and it only has one of the sides left on it. Is this bad for the computer and will the extra dust cause problems? Or should I leave it this way or take the missus wrath and buy a case? If so is there any certain case I should get? I don't care about looks I just want card reader and usb slots and for it to run as cool or cooler than now, my case has 1 fan. Also what are the max temps for my new and old computer parts? Is 40°C under load ok for my CPU, what about 70°C for my GPU is that ok too, or should I worry? What are normal and safe temps for my components? I have looked around but there seem to be lots of different answers. I know that 100°C is bad but I want my parts to last as long as possible and this site always seems to give good replies without arguing or flaming.

  Read the article

• OpenSWAN KLIPS not working

  - by bonzi

  I am trying to setup IPSec between 2 VM launched by OpenNebula. I'm using OpenSWAN for that. This is the ipsec.conf file config setup oe=off interfaces=%defaultroute protostack=klips conn host-to-host left=10.141.0.135 # Local IP address connaddrfamily=ipv4 leftrsasigkey=key right=10.141.0.132 # Remote IP address rightrsasigkey=key ike=aes128 # IKE algorithms (AES cipher) esp=aes128 # ESP algorithns (AES cipher) auto=add pfs=yes forceencaps=yes type=tunnel I'm able to establish the connection with netkey but klips doesnt work. ipsec barf shows #71: ERROR: asynchronous network error report on eth0 (sport=500) for message to 10.141.0.132 port 500, complainant 10.141.0.135: No route to host [errno 113, origin ICMP type 3 code 1 (not authenticated)] Tcpdump shows 22:50:20.592685 IP 10.141.0.132.isakmp > 10.141.0.135.isakmp: isakmp: phase 1 I ident 22:50:25.602182 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 22:50:26.602082 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 22:50:27.601985 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 ipsec eroute shows 0 10.141.0.135/32 -> 10.141.0.132/32 => %trap What could be the problem?

  Read the article

• How can I wipe my iPod classic and fix any bad sectors on the hard drive without killing it?

  - by Sam Meldrum

  My iPod never finishes syncing and only syncs audio, not pictures or video. Any ideas as to how I can fix it? My iPod classic 160GB worked well for a couple of years. I used to sync a lot of photos at full resolution to it, but this recently stopped working after I moved to Windows 7. iTunes is on latest version - 9.1.1.12 iPod software is up to date - 1.1.2 Windows 7 is fully up to date and patched The symptoms are that the iPod will start to sync, all audio (music and podcasts will sync successfully) but the syncing will then just appear to continue - itunes message: Syncing iPod. Do not Disconnect. This sync never completes - I have left it trying for days. I have tried resetting the iPod using the Restore button, whereupon it restarts sync from default options and again will sync audio, but nothing else. I suspect that something has gone wrong on the hard-drive - either a bad sector or some corrupt data. Is there a process I can go through to fix this? E.g. SpinRite or a format? If so how do I go about formatting an iPod and will it be recognised as an iPod after format and work as normal? Any advice on what to try next much appreciated? Update I have eliminated problems with the files, PC or iTunes as they sync fine to other iPods. I have also eliminated the cable by trying different cables which work with other iPods. What I'd really like to know is if there is any way to more fundamentally wipe the iPod safely, attempt to repair any bad sectors on the hard drive and then start from scratch. Anyone ever managed this?

  Read the article

• SQL cluster instance names for large project

  - by Sam

  We're setting up two clusters. One dev and one prod. The Production will host two SQL instances - a OLTP and a DW. The development will host 4 OLTP non-production environments and at least one DW non-production. We're working on getting more DW non-prods and possibly more OLTP systems. I'm considering a naming scheme like this, where PROJ would be 3 initials for the project name. Dev Cluster MSSQLPROJD1\D1 (DEV) MSSQLPROJD2\D2 (TEST) MSSQLPROJD3\D3 (QA) MSSQLPROJD4\D4 (STAGE) MSSQLPROJD5\D5 (DW) Prd Cluster MSSQLPROJP1\P1 (PRD) MSSQLPROJP2\P2 (DW) To the left of the slash, each name must be unique network wide. On each server, the instance name, to the right of the slash, must be unique. Any thoughts on this? I'm trying to avoid having instance names drifting from reality as the project progresses - say we change what we call a certain environment or want to repurpose one. Then we can update a listing of the purposes for the instances and be done with it. How has a scheme like this worked out for you? Maybe you do things another way in your shop - tell me about it. Thanks.

  Read the article

• Computer always freezing after random periods of time. No errors listed.

  - by Wesley

  Hi, all. Here are my specs beforehand: AMD Athlon XP 2400+ @ 2.00 GHz, 160GB IDE HDD, 128MB GeForce 6200 AGP, 2 x 512MB PC3200 DDR RAM, CoolMax 350W PSU, 1 x CD-RW Drive, 1 x DVD-ROM Drive, FIC AM37 Mobo, Windows XP Pro SP3 My desktop freezes after random periods of time but there are no errors listed in the Event Viewer after a forced shutdown and restart. A couple months ago, I found that when it froze, the floppy was being accessed at the same time. So, I disconnected the floppy (since I never used it anyways) from the power supply and motherboard. Everything was working fine and the computer never froze. This past Christmas break, I left for a Conference and when I got home, the computer kept freezing again. So, this time, I just disconnected the DVD reader (from mobo and power) and started it up. Still, it froze almost right away. Then I found some older sticks of RAM (2 x 256MB PC2100 DDR) and swapped them in. Everything worked fine again after that. I even swapped the 2 x 512MB PC3200 DDR RAM back in and everything worked okay. Then it started freezing again, and I tried all possible RAM combos, still freezing within 5-10 minutes of startup. One thing I've realized is that the floppy drive is still listed in My Computer and I uninstalled it from my Device Manager already. There were no software errors, and I uninstalled the most recent software, with no effect. Still, I have no idea what is wrong because everything ran fine before that. Any suggestions? EDIT: Still have yet to buy some blank CD media to use Memtest86+. However, would a lack of virtual memory cause the computer to freeze? EDIT2: So after a long time, I ran Memtest86+ and all is well. Turns out though, after removing my original DVD reader and replacing it with a DVD-ROM drive, there is no freezing whatsoever! Thanks for all your suggestions!

  Read the article

• How to deploy website in IIS with a host name?

  - by Jayakumar

  I try to host my application in IIS. Below are the steps that I follow: Publish the code and place it in a path. Open IIS, right click on "sites" and select "Add Website". In that dialog I gave the site name and selected the app pool created for the application. I selected the physical path of the published code. I left the IP and port in the binding section without changes. and, finally, gave the host name as fus.km.com. When I try to browse the application the page is not Loading "Internet Explorer cannot display the Page" The machine domain is km.com UPDATE I tried to add the host name to the host file and flushed the DNS. The application asked for user credentials (I use windows Authentication in the application). But it did not login. On repeated tries it throws the error: HTTP Error 401.1 - Unauthorized You do not have permission to view this directory or page using the credentials that you supplied. I tried with different user to login but I get the same result.

  Read the article

• How to encourage Windows administrators to pick up scripting?

  - by icelava

  When I worked as an administrator in my first job, I was frustrated that our administration processes with Windows servers were a series of point-and-clicks; we could never match the level of efficiency with the Unix servers which had a group of shell scripts to automate a lot of the work. I soon read about WSH and ADSI and wasted no time learning just how much automation I was able to achieve with scripting. There was a huge problem though - almost none of my Windows colleagues were really interested in learning scripting. They seemed happy with the manually mouse-clicking chores and were never excited at the prospect of using scripts to do the work on their behalf. I struggled to convince them to pick up scripting skills despite the evident increases in efficiency. I left that job in pursuit of a full-time software development career thereafter. Almost a decade on working in various environments and different customers, I still encounter Windows administrators mainly possessing this general "mood" where they would avoid scripting as much as possible. Despite the increasing level of accessibility Windows server technologies are opening up for scripting and automation. I am almost certain the majority of administrators are administrators precisely because they absolutely hate performing any kind of programming duties. What are some means to encourage and motivate administrators that scripting can really help them in the long run?

  Read the article

• Replacing DropBox with: Amazon S3 + SSL + GPG/TrueCrypt + Mounting on OSX ??

  - by Matt Rogish

  So, right now we're using DropBox to share various data files around between approximately 10 Mac OS X systems. However, we already have an S3 account and everyone on the lowest DropBox plan of $10/mo seems too expensive. So, I am contemplating something that would allow us to replace DropBox with our own home-grown solution. We are all fairly technical people and/or smart enough to follow some steps, so if it's not as "user friendly" as DropBox we're all comfortable with that. There are plenty of docs out there that have bits and pieces of what I want but some of the tools don't seem to fit the requirements: Transport security via SSL to the bucket Encryption of bucket contents Bi-directional syncing Most of the scripts I can find on the internet use "duplicity" which appears to fail #1 (it doesn't look like duplicity supports SSL to S3 - the docs don't state but the protocol looks plain old http http://www.nongnu.org/duplicity/duplicity.1.html#sect6 ) Many scripts use gpg to encrypt files. This seems like it could work, however I have to make sure that each OSX client is able to use the same key to encrypt and decrypt files (key management is left to me to manage). Finally, most of the scripts use one-way replication, e.g. using Amazon S3 as a simple backup store. As we'd be using Amazon S3 as the "repository" they fail this one. Whew. So, I'd love a single tool that does this but after an exhaustive search I don't think one exists. I'd be happy just knowing which tools out there can fulfill my 3 requirements, after that I can stitch together the rest. Any thoughts? THANKS!

  Read the article

• General name for Macs' operating system

  - by andy124

  First of all, I hope that my question is fairly suitable for this site. I have a website where I would like to write articles about some operating systems. Therefore, I have created a main category called "Operating systems". Within a subcategory, I would like to write articles about Apple's operating system that is running on Macs. However, I do not know what to name this category. I have always thought the name was just OS X, but come to think about it, the "X" is actually part of the version (10). Therefore I cannot exactly call my category OS X, because what about when OS 11 is released in a few years? And since Apple has gone from Mac OS X to just OS X, then I cannot use "Mac OS". And, if I remove the X from OS X, then I only have "OS" left, which does not seem so proper. I am really looking for a meaningful all-round name for the Macs' operating system that does not involve the versioning. I was thinking about just calling the category "Mac", but that is not precise either - but perhaps the closest I can get?

  Read the article

• Cisco Access switch is dropping large amount of end points

  - by user135458

  This afternoon, with no changes to the network, a switch suddenly started dropping off lots of connections. These connections would come back up a few minutes later, then another area connected to the switch would drop off. This is an older 4006 chassis switch which could in and of itself be a problem but I'm looking to see what else you all would look for in trying to find a root cause. Switch is connected via ports 1/1 and 1/2 in an etherchannel to a VSS core 1/1/42 and 2/1/42. Both sides are up and working however the CPU on the switch will spike up to 99% and that's when CRC errors start to hit the VSS core on one of those interfaces and end points start dropping off. We tried new transceivers and SFP's on each side of the link, same result. When we tried swapping the fiber patch cables on the access switch the CRC errors did not follow the fiber cables they stayed with port 1/2 on the access switch. So port 1/2 on the supervisor module looks like the culprit. We actually tried to create a new member of the ethernet channel by taking a fiber media converter to cat5 and make that a member of the port-channel but when we plugged it in you couldn't even reach the switch. I'm guessing that's unrelated and a problem with the media converter. As of right now we have left it in a state of only one fiber cable running to one side of the VSS core (1/1 Access Switch -- 2/1/42). I've sent some info into TAC and they are looking into the situation but does anyone else have any commands I could run or some troubleshooting I could look into in the meantime?

  Read the article

• What is the main reason of adsl modem/routers dying ?

  - by ldigas

  The other day my home adsl modem/router (dwg 684t in this case) died. A guy from the telecom company came, brought another so no problem in day to day operation, but he also left this one. Now, I'm interested ... it didn't fall, it wasn't electrocuted ... but it just doesn't work. What could be the problem ? Can they be fixed ? Is it worth it (in which case I would have two which is always nice) ... What are the usual problems that occur with them ? In this case, I can connect to the router, I can see its settings, I just can't connect to the internet. With the new one everything works. Weird. Edit: Additional question: Can those things be fixed ? I mean, is it worth giving it to a local tinker for him to experiment on it ? I'm not looking for a definite opinion, just your personal advice ... (although in the end I think I'm gonna archive it in the "cylinder register")

  Read the article

• Windows 8 Pro Homegroup Not Allowing Access to Shared Files

  - by Jack Herr

  I have two pc's and a laptop. With all three running Windows 7, homegroup worked perfectly, with all computers able to access the files on the others exactly as one would expect. I installed Windows 8 Pro, which I downloaded recently from the MSDN website, on the laptop. From the info on the MSDN website, I believe the version downloaded is the official release version, not a release candidate. The install preserved all settings, apps, and files. I cannot connect to the homegroup from the laptop. Well, not exactly. I joined the homegroup during the install, and later left and rejoined, that was advertised as being offered by one of the pc's (not sure why that one was picked and not the other or both). This homegroup appears in my "computer" folder in the file explorer, offering files from that pc. But it excludes documents (only the music, pix, videos, and playlists folders on the one computer appear). I can actually access those files from the laptop. But the Homegroup folder, which actually shows all the computers by account and computer name and includes documents from both computers, does not open those folders when clicked. The computers listed by name in the Network folder give me a login that doesn't work. It asks for a username and password, no combinations of which work. Further, the following error message appears before the login is even attempted: "The system cannot contact a domain controller to service the authentication request. Please try again later." The two windows 7 pc's continue to share all files, including documents, seemlessly. I can also get to the laptop shared files, which I shared during setup, from either pc. Any ideas?

  Read the article

• Internet Sharing on Lion breaks my routing table

  - by seaders

  When in the office, I'm connected to a 192.168.1.0/24 network. When Internet Sharing is off, when I run netstat -nr the first entry shows default 192.168.1.254 UGSc 10 62 en0 If I turn Internet sharing on, it shows default link#5 UCS 2 0 en1 This is obviously incorrect and breaks all connectivity of my machine. en1 is my wireless, whereas en0 is my ethernet. If I then disable Internet Sharing, it even deletes that incorrect route, so I'm left with no default route at all. Currently I have one script that I run when I share, or after, when I disable that does route delete default route add default 192.168.1.254 That fixes everything, but I'd love to know what's actually making this happen and how to properly fix it. And just to say that at some point a few months ago, this was working absolutely perfectly, with no hitches, then one day when I brought the laptop home, I couldn't disable the internet sharing, so I couldn't connect to my home wifi. I eventually had to restart the machine and since then this problem has been happening. Any help would be greatly appreciated, thank you.

  Read the article

• Windows 7 boots to black screen with blinking cursor

  - by murgatroid99

  I have an Alienware M17x that dual boots into Ubuntu 11.04 and Windows 7 Home Premium. Currently, the computer starts at the GRUB loader and will boot into Ubuntu, but if I try to boot into Windows, I immediately get a black screen with a blinking cursor in the upper left corner. The output of fdisk -l is Device Boot Start End Blocks Id System /dev/dm-0p1 1 5 40131 de Dell Utility Partition 1 does not start on physical sector boundary. /dev/dm-0p2 6 1918 15360000 7 HPFS/NTFS Partition 2 does not start on physical sector boundary. /dev/dm-0p3 * 1918 64772 504878877+ 7 HPFS/NTFS Partition 3 does not start on physical sector boundary. /dev/dm-0p4 64772 77827 104858625 5 Extended Partition 4 does not start on physical sector boundary. /dev/dm-0p5 64772 67204 19531008 83 Linux /dev/dm-0p6 67204 74498 58593536 83 Linux /dev/dm-0p7 74498 77577 24731648 83 Linux /dev/dm-0p8 77578 77827 2000128 82 Linux swap / Solaris I have used the Windows rescue CD, and run the automatic error fixer until it finds no errors. I have run chkdsk /R on both the main Windows 7 (/dev/dm-0p3) partition and the recovery partition (/dev/dm-0p2). I set the main Windows 7 partition to be active. I also tried running in the recovery console the commands bootrec /fixmbr bootrec /fixboot bootrec /rebuildbcd None of these helped and the last set of commands deletes grub, which I then have to reinstall from Ubuntu. I think the last thing I did in windows before this started was install the newest ATI driver for my video card. This would suggest using system restore, and I actually had a restore point earlier (after the problem started), but after whatever I did that restore point does not appear in the list on the recovery disk any more, so I cannot do a system restore. Is there anything else I can try to make Windows boot properly again? Edit: Running the suggested commands bootsect /nt60 c: bcdboot c:\windows /s c: was also ineffective.

  Read the article

• Will wear induced by turning computers off in the evening be offset by energy savings?

  - by sharptooth

  I'm asking this here because this is primarily a huge office scenario and administrators will more likely have the answer I'm looking for. Employees' desktop computers can be either left turned on for the whole night or switched off in the evening and turned back on in the morning. The latter will surely save energy. In the same time turning on and off is very harmful for the equipment - hardware often breaks specifically when turned on. Both energy and hardware replacements cost money. With energy it's quite obvious - you pay every month according to what your power meter shows. With hardware replacements it's worse - you need qualified stuff to quickly diagnose the problems and once something breaks the affected employee will have to wait for some time while his computer is fixed/replaced and the data is recovered. So the company has to choose between saving money on energy and saving money on computer maintaince and lost hours. Such decisions must be well though. Is there any detailed study of how turning computers off each evening affects their lifetime?

  Read the article

• Wordpress advanced navigation [closed]

  - by codedude

  Ok, so I've made a site template in pure html and I need to convert it into wordpress. The navigation code looks like this: <div id="header"> <div class="wrap"> <ul id="leftnav"> <li><a href="about.html">About</a><span class="arrow"></span></li> <li><a href="work.html">Work</a><span class="arrow"/></li> </ul> <div id="logo"> <h1><a href="index.html">T.Wiersema</a></h1> <span class="arrow"></span> </div> <ul id="rightnav"> <li><a href="blog.html">Blog</a><span class="arrow"/></li> <li class="contact"><a href="#">Contact</a><span class="arrow"/></li> </ul> </div> </div> The leftnav is absolutely positioned to the left and right nav is absolutely positioned to the right with the logo centered between the two. Notice also how I have a span inside each li element. Is there a way to reproduce this in my wordpress theme without just manually copying this into it?

  Read the article

• Desktop PC does not power up on power button

  - by hIpPy

  When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. Update: I left the desktop off for a few days and it started. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Update: I always keep the desktop running and I never shut it down. During updates or manual restarts, it powers up without issues. I wonder if this sheds lights on the issue. Any idea how I can narrow down the issue? ex: if I can find if the PSU is dying etc. I'd really like to fix the issue. Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp3 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

  Read the article

• How to manage multiple email addresses on multiple domains in Exchange

  - by CAD bloke

  Using Hosted Exchange Server, mostly because I use an iPhone, webmail & Outlook on 2 laptops. I want to keep everything consistent and unfragmented. Also, I want push notifications. I have 2 domains, a professional one & a personal one. Each domain has about 5 (give or take) email addresses I use for various purposes. Each domain also has a few parked domains (.net, .org, .info) aliased to the .com domain. I would like to keep emails from the 2 domains separated. Do I need an extra mail box, meaning extra expense or can I create another Exchange user on the same mailbox and create an extra account in Outlook? In either case I will have to wait for iOS4 on the iPhone to manage 2 Exchange accounts. Or am I better off just using a set of rules and folders? The aliased domains are another joy to behold entirely. It looks like I will have to add each email address variant individually. Alternatively, I reckon I may just leave the aliased domains at the pop3 host and let Outlook gather those as edge-cases. Surely I can't be the only one making my life this difficult. Anyone out there done this? From the left field - is this (much) easier in gMail? I'm not committed to Exchange (yet). Previously I used Outlook as a pop3 client with a set of filters to direct incoming traffic to folders. This worked with the aliased domains because my host directed all the aliased TLDs to the same mailbox.

  Read the article

• Virtualizing an Inline network appliance with VirtualBox (or VMWare)

  - by Tzury Bar Yochay

  My device, which is a Linux based IP in-liner is transparent to the network peripherals, that is, no IP address assigned to any of its interfaces. For the sake of the conversation, let's use ADSL connection as an example, while the device is inspecting the bi-directional traffic, the network is behaving same as if device was not there, attached to the wire (see Physical setup at the attached diagram). I wonder if I can enclosed that "device" within a Windows machine and have it operated virtually so it still seats inline between the ADSL router and the Windows netwroking interface by using virtual NICs, (or whatever their name is in windows), and inspecting the traffic, same as if it was on a separate physical device, the drawing under "Virtual Setup" in the attached diagram show what I am trying to achieve. Reading a bit on the VirtualBox docs, seems like binding the right side is relatively simple, perhaps I should have one network adapter set as Bridge Networking and VirtualBox will connect it to the physical NIC on the host machine, and network packets are exchanged directly, circumventing the host operating system's network stack (WinXP in my case). However, I have no idea how to achieve the left side of my diagram, which requires adding virtual NICs to windows and configure them correctly in a way to make that pipeline possible. I would appreciate any help. by the way, if that is not possible with VirtualBox but with other virtualization solution (e.g. VMWare), I would accept the other as well.

  Read the article

• How to get Synergy working on Ubuntu 11.10 and Windows 7?

  - by Linda

  I'm using Ubuntu 11.10 32-bit and Windows 7 64-bit, however, Synergy only works when a window (application or folder) is open and touching the edge of the screen where the mouse should "jump". In other words, if a window is open and maximized, Synergy works normally. Without any windows, the mouse does not jump to the other screen. My steps: (Ubuntu) apt-get install -y quicksynergy (Windows) Install Synergy (I've tried both 1.3.8 and 1.4.8 and both 32 and 64-bit) On Ubuntu 11.10 32-bit (Synergy Server config): ~/.quicksynergy/synergy.conf section: screens myubuntu: mywin7: end section: links myubuntu: right = mywin7 mywin7: left = myubuntu end On Ubuntu 11.10 32-bit: $ /usr/bin/synergys -f --config .quicksynergy/synergy.conf ... 2012-04-25T14:04:12 NOTE: client "mywin7" has connected /build/buildd/synergy-1.3.6/lib/server/CServer.cpp,287 (output hangs here) On Windows 7 64-bit: Synergy 1.3.8 Client on Microsoft Windows 7 x86 (WOW64) started client connecting to 'myubuntu': ###.###.###.###:24800 connected to server (output hangs here) At this point, things should work, but my mouse still can't change screens unless a window is maximized on my Ubuntu machine. Everything is running on port 24800. No firewall on Ubuntu. Firewall port 24800 open on Windows 7. This was previously working on Ubuntu 10.10 and Windows 7 (so only Ubuntu has been upgraded). I'm open to using either 32 or 64-bit on either server or client side, but I just want to get it working on Ubuntu 11.10 and Windows 7! I'm also using Ubuntu Classic (no effects), and not Unity.

  Read the article

• Can't access WordPress blog after host changed IP address of server

  - by John

  My host changed servers and all websites now have a new IP address. I have the same domain name and I assume the host runs the same nameservers, though my host and domain name provider are different. Notes: I never entered a Name or description under General/Settings for my blog. I left them both blank. That is when I could log into it. The wp-config file, has localhost entered rather than a specific IP. Again this has always been the case and my host never advised otherwise. I can get into cPanel by simply putting the newly advised IP in front of /Cpanel. However, I can not reach the admin panel of my WordPress blog (version 2.8.2). I had been loggin into it via http://xx.xx.xxx.xx/~example/blog/wp-login.php. My host suggested to simply insert the new IP in place of the old one. I still get the error message: 404 Not Found The server can not find the requested page: Apache/2.0.63 (Unix) mod_ssl/2.0.63 OpenSSL/0.9.8e-fips-rhel5 mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 PHP/5.2.12 Server at 74.50.108.14 Port 80 I followed some tips on a question on Stack Overflow of a similar nature. I have logged into phpMyAdmin and found the wp-options table and searched for SELECT * FROM `wp_options` WHERE `option_name` IN ('siteurl', 'home') Only option ID 39 came up and the results are: Home has optionvalue http://example.org siteurl has optionvalue http://example.org/blog Both of which appear correct. Is there any part of the MySQL tables where I can change an actual IP address? Or is there something else you can advise?

  Read the article

• Reducing both pagfile.sys and hiberfil.sys in Windows 7

  - by greenber

  I recently used Defraggler to consolidate my free space areas on my D: drive preparatory to using Disk Manager to break my drive into two areas, one as my "data area" for Windows 7 (normally on my C: drive) and to experiment around with Windows 8. The Defraggler program works so well I ran it on my C: drive and I ended up with a lot of free space both on my C: drive and my D: drive. I was very happy. And then I woke up the next day and I've got virtually no free space left, something like 8 MB on my C: drive and about 3 GB on my D: drive. I then ran Wintree (which gives a nifty graphical representation of disk usage) and found I had a large page file and a large hiberfil. So I temporarily turned off hibernate and reduced the page file size to 2000megabytes and then rebooted so that both would take effect. It had no effect on the C: drive or the D: drive. That makes no sense to me. What caused the free space on each drive to disappear, why doesn't the page file size being reduced and the hibernate file being turned off free up disk space to either the C: or the D: drive? Would it make sense to delete the two files in question and, if so, how do I go about doing that? Safe mode? Thanks. Ross

  Read the article

• Raid 5 with hot spare or RAID 10 with no hot spare?

  - by Boden

  Yes, this is on of those "do my job for me" questions, have some pity:) I'm at the limit for what I can do with the number of hard drives in a server without spending a substantial amount of money. I have four drives left to configure, and I can either set them up as a RAID 5 and dedicate a hot spare, or a RAID 10 with no hot spare. The size of each will be the same, and the RAID 5 will offer enough performance. I'm RAID 5 shy, but I also don't like the idea of running without a hot spare. I'm not so interested in degraded performance, but the amount of time the system is without adequate redundancy. The server and drives are under a 13x5 4 hour response contract (although I happen to know that the nearest service provider is at least 2-3 hours away by car in the winter). I should note that the server also has two RAID 1 arrays which would also be protected by the hot spare. Why don't they make drive cages with 9 bays! Heh.

  Read the article

• How to merge arbitrary snapshot into base vdi in Virtualbox

  - by jmathew

  I botched a transfer of a VM from one harddisk to the other. Now I'm left with the base vdi and a whole bunch of snapshots. My steps Copied old VM directory over to new HDD Deleted old VM and added new VM using using Machine-add and providing the old XML file Couldn't add base vdi file due to conflict so changed the UUID of base vdi with VBOXMANGE.EXE internalcommands sethduuid <path/to/vdi> Attempt to rollback to a snapshot, but it seems the VM is looking for the snapshots on the old HDD (which is formatted and gone) This is the error (networked is the name): Failed to restore the snapshot networked of the virtual machine lfs. Could not open the medium 'H:\vm\ft.vdi'. VD: error VERR_PATH_NOT_FOUND opening image file 'H:\vm\ft.vdi' (VERR_PATH_NOT_FOUND). Result Code: E_FAIL (0x80004005) Component: Medium Interface: IMedium {53f9cc0c-e0fd-40a5-a404-a7a5272082cd} The old HDD was drive H: the new one is drive N: How can I modify the snapshots/VM to look in N:\vm\ft.vdi for the base vdi? I've already set the default settings in VirtualBox in general (default vm/vm snapshot location). Or if not that how can I merge the old snap shot with the base vdi given that the only things that have changed is the base vdi's UUID?

  Read the article

• Printing from Firefox on different printers and setting the page details beforehand

  - by user1162541

  I´ve got an odd problem and I have not been able to fix this. I have a computer which is connected to two printers. One is a receipt printer (EPSON TM-U220), and the other one is an impact printer (Epson LX-300+). From Firefox, I need to print on both printers at different moments. So first I print on the receipt printer, then on the impact printer, etc. However, whenever I first print on the receipt printer, and then go back to the impact printer, the printout is only the width of the page of the receipt printer. That is, the page does not come out properly, just the left part of the page is used for printing and the right part is completely empty, as if I am just printing on the small receipt paper. And there is no way I can tell Firefox that I am printing on this larger printer. The second print on the impact printer goes fine. Firefox now knows it is printing on the impact printer, and it comes out properly on the full page width. But every first print on the impact printer is using the wrong paper size. How can I fix this? When I go to PAGE PREVIEW I can not set the printer UNTIL I actually print the page. If I go to PRINT PREVIEW CONFIGURE PAGE, I can not set the printer I will be using. I can only do so if I go to PRINT PREVIEW PRINT (here is the dropdown box to set the printer). But I can only set the printer and then click PRINT, or CANCEL. If I click PRINT, then the computer remembers the setting but that page will come our wrong, and when I click cancel it simply does not remember the printer I just set.

  Read the article

< Previous Page | 590 591 592 593 594 595 596 597 598 599 600 601  | Next Page >