Search Results

Search found 31774 results on 1271 pages for 'chris go'.

Page 598/1271 | < Previous Page | 594 595 596 597 598 599 600 601 602 603 604 605  | Next Page >

  • Is there any reason to subnet a home network?

    - by Will
    For networks I understand we set a netmask on each computer to let it know what IPs it can talk to without going through the router - IPs on the same subnet can talk directly to each other and do not have to go through a router/switch. However, in today's home networks (and I suspect corporate networks as well) every computer is connected to a router/switch (at the low cost of today's hardware I doubt there it much of a market for wired repeaters/hubs). This seems to obviate the need for a subnet mask and subnetting. Considering that in most modern home architectures every computer goes through the router, even to talk to computers on the same network, is there any reason for me to subnet a home network?

    Read the article

  • How to (hardware) RAID 10 on Ubuntu 10.04 LTS with 4 drives and motherboard with RAID contoller

    - by lollercoaster
    I have 4 500GB hard drives. I set up a RAID 10 in BIOS, much like shown here: http://www.supermicro.com/manuals/other/RAID_SATA_ESB2.pdf Then I followed these instructions: http://www.unrest.ca/Knowledge-Base/configuring-mdadm-raid10-for-ubuntu-910 Basically I cannot get it to work. I go through the instructions when I get to the "partition" section of the install, creating 4 RAID 1's (2 partitions on each drive, one for primary and one for swap space), then combining to make a RAID 10. Unfortunately it still shows 2 partitions, one 500 GB and another being 36GB for some reason. Any ideas? I think best would be if anyone had found good instructions (step by step) for how to do this...I've been googling for hours and haven't found anything...

    Read the article

  • Black screen on Ubuntu 12.04

    - by user1648371
    I've just upgraded to Ubuntu 12.04 and I'm experiencing some problems. The first thing I noticed is that when I click the Workspace switcher all I get is a black screen (I can guess where the different workspaces are located and clicked on them, not a practical solution though). In addition when I lock the screen or suspend the laptop (a Vaio VPCEB4M1E) I get a shifted screen (I see the right most vertical stripe on the left size of the monitor and nothing about all the rest, to put it clearly I can see the gear that allows me to turn the pc off, etc, but not much more..) when I go to the additional driver menu I see the "ATI/AMD proprietary FGLRX graphics driver" are installed and the post-release update version is available. I don't know if the problem is driver related, so before doing anything I'd like to get some suggestions from you guys. Thanks you!

    Read the article

  • Any reason to prefer video adapter with two DVI ports versus one DVI/one VGA for DVI/VGA optional dual monitors?

    - by Bryce Thomas
    I am looking to buy a new video card to power two identical monitors. The monitors came with both DVI and VGA cables, so I am able to use either. My current video card has two DVI ports on the back, so I have both monitors connected via DVI at present. I have noticed that many modern video cards have a DVI/VGA/HDMI port trio and that cards with two DVI ports seem somewhat more scarce. Essentially, I have more options available to me for purchasing cards with a DVI/VGA/HDMI trio than with a DVI/DVI duo. My question is, are there any sound reasons to go to the extra effort of finding a card with two DVI ports versus simply running one of my monitors through a DVI and one through a VGA on a DVI/VGA/HDMI card? Quality differences? Any variety of image asymmetry? Configuration difficulties (I dual boot Windows and Ubuntu)? Anything else?

    Read the article

  • How to set the preffered network interface in linx

    - by Mike Cooper
    I have my network set up like this. http://docs.google.com/Doc?docid=0AZ1YxuLE4djaZGhqN2s1NmRfMjhjNjc0Ym1meg&hl=en In words: I have a machine (Calcium, running Arch Linux) that has two network interfaces. eth0 is hoooked up to a router, and is gigabit. Eth1 is hooked up directly to the university network over 10Megabit. The router's uplink is hooked up to the university network as well, and it is also 10Megabit. Currently (I believe) all traffic on Calcium is going through eth0, through the router, regardless of whether it is internal or external. (How can I confirm this?) Ideally, traffic that is destined for the internal network (192.168.10.0/24) would travel over eth0 to the router, and wherever it is going. ALL other traffic should go over eth1. I suspect that this behavior could be acheived with IP tables? I don't really know where to start looking to learn that though, so any links would be appreciated.

    Read the article

  • How to remove 'ApacheMonitor.exe' from notification area

    - by ekaj
    For some reason I had 2 instances of Apache running, and I have no idea how. I also had two instances of ApacheMonitor.exe showing in the "Notification Area Icons" place when you right click on your taskbar and go to properties. To fix the multiple instance issue, I deleted Apache completely and uninstalled the service (I did not use the .msi, I install from a .zip). Anyways, Everything from Apache is gone except the two things in the Notification Area Icon page. Does anyone know how to remove these two icons? I have completely uninstalled Apache, cleaned my registry with CCleaner, and rebooted. Does anyone have any other suggestions? Despite what the picture says, I do NOT have Apache installed, and it is not running.

    Read the article

  • How do I restore a non-system hard drive using Time Machine under OSX?

    - by richardtallent
    I dropped one of the external drives on my Mac Pro and it started making noises... so I bought a replacement drive. No biggie, that's why I have Time Machine, right? So now that I have the new drive up and initialized, how do I actually restore the drive from backup? Time Machine is intuitive when it comes to restoring the system drive or restoring individual folders/files on the same literal device, but I'm a bit stuck in how to properly restore an entire drive that is not the boot drive. I saw one suggestion to use the same volume name as the old drive and then go into Time Machine. Haven't tried that since the information is unconfirmed. For now, I just went to the Time Machine volume, found the latest backup folder for that volume, and I'm copying the files via Finder. Of couse, I expect this to work just fine, but I feel like I'm missing something if that's the "proper" way to do this.

    Read the article

  • Connecting together DIR-615 and DIR-655

    - by ra170
    On my DIR-655 my internal network is: 192.168.0.x On my DIR-615 my internal network is: 192.168.1.x They are both connected to my firewall PIX 501 box The PIX itself is connected to the comcast modem. I briefly looked at the menu options on those router and they look similar, however I'm not sure what's the best way to connect those two together so that I can go between those networks. (printing, file browsing, etc.) I'm not sure if I have to do this somehow on those two router or on the PIX itself, or probably on all of them. If anyone has experience with something like that please let me know..

    Read the article

  • How to get rid of resume information on ubuntu 9.10 ("karmic")

    - by Glen S. Dalton
    I am on an old laptop with Ubuntu 9.10 installed. I once tried to not shutdown but go into one of the resume states. On the next power on, resume did not work, but there was an error message during boot asking me for the resume image (which I do not have or know of) and when I press enter the normal boot happens. But this error pops up on every boot now. How can I get back the behaviour from before? Why does the boot process guess there would be a resume image and can I delete this information? I would like to post here the error messages from the boot proces, but they are not in /var/log/syslog, where else can they be?

    Read the article

  • USB hard drive doesn't graceful power off after eject on Windows 7

    - by Sim
    I have a couple of Seagate FreeAgent Go external USB hard drives and would like them to gracefully power off after ejecting in Windows 7. With Windows XP a few seconds after they are ejected they gracefully power off. When ejecting them on Windows 7 they just stay on and have to be physically disconnected before they lose power. I have checked the hard drive removal policy and it is set to quick removal. I have also looked in the Seagate forums but I couldn't find any info on this so I thought I'd ask the SuperUser community on any ideas why the difference and how to get the same behaviour in Windows 7 as in XP? Update: I am finding that this also happens with USB thumb drives as well. My current theory is that there were changes to the driver model with Vista/Win 7 that haven't been reflected in the device drivers yet. So things that worked under XP don't under Win7 as the drivers haven't been updated for the new model. Does that sound right?

    Read the article

  • How to configure Exchange Server with AutoReply that sends the reply only once?

    - by Abel
    If you configure Exchange Server 2007 for auto-reply on a public address, and the reply is sent to an address that also has auto-reply or out-of-office-auto-reply, then Exchange Server will receive a new message, same from-address, and will again send an auto-reply. This can go on forever and can potentially lead to a DoS situation. How can I prevent multiple sending of auto-reply to the same address, preferably in a given timeframe (to prevent legitimate multiple mails to be treated incorrectly), using Exchange Server 2007? Our XS hosting provider says it cannot be done, but that strikes me as odd.

    Read the article

  • Setting up a Windows Server 2008 R2 DC + Fileserver : native or virtual?

    - by user126890
    I want to deploy a new DC + Fileserver using Windows Server 2008 R2 SP1 Standard Edition on a Dell PowerEdge R410 and iSCSI storage for a small business (~30 people). Should I install the system native on the server or use a virt layer? I don't have a budget for virtualization so i gotta go with something free... What's a better working routine, taking snapshots of vm's or taking backups (Acronis/CloneZilla) of systems? If I use a virt system, I need a GUI for some people in the business to reset the system to a earlier state in emergency situations. I wanted to install phpVirtualBox once but never finished, is it suitable in a productive environment? server specs: Intel Xeon E5620 CPU (2,40GHz, 4C, 12MB Cache) 8GB RAM Dual Rank LV RDIMMs 1333MHz 2x 1TB SATA 7,2K 3,5, RAID1

    Read the article

  • Windows Server 2003 seems to pick the 'outgoing' IP address at random from all the ones configured in IIS, how can I make it just use one?

    - by Ryan
    We have multiple sites in IIS with different IP addresses. This is cool, want different IPs to all go to this server and use the proper site. However I discovered an issue that when the server makes an outgoing connection, I cannot predict which IP it will use. I had to have one client add ALL the IPs to their firewall so that a certain service could communicate with their server. Well now the time has come to add another IP/site to IIS but I had told them they would not need to add any more IPs. So the question is, how can I make Windows Server 2003 use only ONE specific IP for outgoing calls instead of it being unpredictable? If this is not a good enough description, when I was RDPed into the server and I opened IE and went to 'what is my IP' it was sometimes different which is how I discovered why the one client's firewall was suddenly refusing the connections. How can I just make outgoing calls originate from a static IP yet still allow multiple IPs pointing to different sites in IIS?

    Read the article

  • VirtualBox reinstalling & updating has left me with Too Many Network Adapters. How Do i remove them?

    - by S3curityPlu5
    I have too many network adapters. I have had to reinstall, repair VirtualBox a few times, and I have three NICs in my laptop. I definitely don't need to have 14 bridged networking drivers though, and I cannot uninstall them. I only want to keep the new ones that came with VirtualBox 4.1.20. When I go into the registry there are tons of places with these adapters. I have searched online up to 10 pages of Google, and VirtualBox forums, and no one has mentioned this problem nor explained how to delete these annoying extra network adapters. Please offer some assistance or at least tell me how anybody else has dealt with this. I only need 1 host-only network adapter, 1 bridged networking adapter for each of my network cards. Take a look:

    Read the article

  • Hyper-V Manager: right-clicking on remote VM crashes MMC snap-in

    - by Greg Bray
    I have a Windows Server 2008 R2 Enterprise SP1 machine that I log into and use to manage virtual machines running on multiple Hyper-V servers on our domain. Sometimes, when I right-click on a remote VM, the Hyper-V Manager will crash and display the following error message: If I use the Actions menu on the lower right, it works just fine, but for some reason right-clicking causes MMC to stop working. Is there any way to fix this issue? Here are the full details of the error message. Description: Stopped working Problem signature: Problem Event Name: CLR20r3 Problem Signature 01: mmc.exe Problem Signature 02: 6.1.7600.16385 Problem Signature 03: 4a5bc808 Problem Signature 04: Microsoft.Virtualization.Client Problem Signature 05: 6.1.0.0 Problem Signature 06: 4ce7c9e3 Problem Signature 07: 342 Problem Signature 08: 1f Problem Signature 09: System.OverflowException OS Version: 6.1.7601.2.1.0.274.10 Locale ID: 1033 Read our privacy statement online: http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409 If the online privacy statement is not available, please read our privacy statement offline: C:\Windows\system32\en-US\erofflps.txt

    Read the article

  • IE9 Kiosk Mode scheduled task opens behind taskbar

    - by greg27
    I've set up a scheduled task in Windows 7 Pro to open up Internet Explorer 9 (x86 version) in kiosk mode. The scheduled task executes when a certain user logs in, and this user is logged in automatically when Windows starts. This is the command I'm using to start IE: "C:\Program Files (x86)\Internet Explorer\iexplore.exe" -k http://example.com So far so good - the computer boots up, the user gets logged in, and IE opens up in kiosk mode. The problem is that IE seems to open behind the taskbar - so the taskbar (start menu, pinned programs, etc.) appears at the bottom of the window, and the bottom of the IE window is visible through the taskbar (since the taskbar is translucent). Is there anything I can do, preferably without installing any third party programs (although I will go for that option if none other is available), to ensure that the IE9 kiosk window always opens in front of the taskbar?

    Read the article

  • Can't save DB password in BDE Admin v5.01 (c. 1998)

    - by Ryan Armstrong
    I have a legacy version of Goldmine running which uses BDE to connect to an SQL2005 server. I'm moving the goldmine application and its database onto a new server and all is fine with the exception of the master DB password. When Goldmine starts it prompts for the password. I enter the password and all is fine but I want the prompt to go away. The password appears to be saved and obfuscated somewhere on the old server but this was configured before my time. As best I can determine, I use the bdeadmin.exe tool to modify the idapi32.cfg file but there is no password option.

    Read the article

  • Windows 7 Change internet time settings tells me I have no permissions.

    - by Matthias Vance
    LS, While trying to solve my computer clock always running ahead (even when on, not just on every boot), I apparently broke some security settings. All I did (as far as I can remember) was stop and start the w32time service. Now, whenever I go to the "Internet time" tab, and click "Change settings..." Windows tells me I don't have permissions to do so. Facts I am a member of the Administrators group. In gpedit.msc, I checked that the Administrators group is allowed to change the system time. Kind regards, Matthias Vance

    Read the article

  • Skype Optimization - Port Forwarding on a Router

    - by user19185
    I was watching this Video which talked about using port-forwarding to optimize your LAN for skype calls. According to the video, as explained in the first couple of minutes in the video, the reason you would need optimization is because if the person your call has a firewall setup, your connection has to go-through a third-party computer to connect to them. I believe I stated this correct (maybe not). None the less, my question is this: do both parties on the call need to enable port forwarding to optimize skype, or just one party (person)?

    Read the article

  • RHEL 4.8 / Sybase 12.5.4 64 bit install error - I have libaio i368 installed I need libaio x86_64 in

    - by Jon
    I am trying to install Sybase ASE 12.5.4 64 bit. I know the machine has a 64 bit processor It is giving me an error during install saying: "error while loading shared libraries: libaio.s0.1" I run the command: rpm -q --qf '%{NAME}-%{VERSION}-%{RELEASE} (%{ARCH})\n' libaio Which returns: libaio-0.3.105-2 (i386) I found a src rpm for libaio-0.3.102. I followed the steps to install which included using make. It appeared to install without error. But when I run the rpm -q command again I still only see the i386 version installed. Not really sure where to go from here. Ideally I would like to find a regular rpm of libaio x86_64 for RHEL 4.8. If I were to find one would I upgrade the package that is already there? Would I remove and install the new one. Or would I install and two separate version of the library?

    Read the article

  • Cause of flapping UNKNOWN Nagios status?

    - by jldugger
    We run some Nagios service checks via OpsView, and one of our hosts is getting a strange response for SSH: "UNKNOWN: Service results are stale" It happens regularly, but seems to go away as the system retries a 2nd and 3rd time. It started after a patch and reboot of the server in question last week. The system itself responds to SSH from boxes I've tested with (which doesn't include the monitoring system I am not given access to). /var/log/secure is full of lines ala: sshd[15628]: Did not receive identification string from xxx.xxx.226.20 Time stamps are reliably every five minutes, which is pretty obviously the monitoring script disconnecting once it gets a login prompt. Anyone know what might be causing this, or how to fix it? It's really frustrating to see this pop on and off the status page.

    Read the article

  • Synergy: server refused client

    - by Tom
    I am trying to get Synergy up and running from a new Windows 7 computer, to an XP computer. The Synergy installations seemed to go fine. I configured each to start on start-up, which they seem to, but the client won't connect. I get repeated: "server refused client with our name" messages in the log output. The Synergy FAQ says to "Add the client to the server's configuration file." But I can't seem to find an instruction set on how to do this. I've looked and looked, but I'm lost...

    Read the article

  • Where is the Mac Divx Web Player 7 cache folder?

    - by user30710
    Until recently, I was using Divx web player 1.4.2 because it seemed to be the least buggy. It was saving files in users/xxxxxx/movies/divx movies/temporary added files and was deleting them when the cache limit was reached. Now with 7, it's saving them alright cause I can watch my HD space go down, but I can't find them. And it's not respecting the cache limit size (mine is 4GB). The only way to clear up this space is a restart of the Mac. I'm running 10.6.8and Chrome. I've looked everywhere for the folder manually. Where is it?

    Read the article

  • What cloud backup solution supports a "backup server to cloud" configuration?

    - by Gepeto
    What online backup tool allows you to: A) Back up Windows, Linux and optionally Mac desktops and servers to the cloud B) Do so by first backing up to a central server or appliance C) Allow restoring from that appliance when possible and if not go to the cloud For now the best option I have seen is i365 by seagate with an appliance between the local computers and the cloud. I know Microsoft also has an i365 plugin for DPM, as well as an Iron Mountain plugin. However, I feel that there must be a simpler way to do this. Can any of the "simpler" solutions like Jungle Disk or anything else going to s3, Mozy, Carbonite, Crashplan, etc do this? Thank you

    Read the article

  • How should I host a site that could potentially get a short spike in traffic of 1000%+

    - by James Simpson
    This is a purely theoretical question, but what if I had a site that would normally only get a couple thousand hits a day, but for a few days each month that could shoot to several hundred thousand or even several million hits over the period of 1-3 days. The site would be pretty bare-bones (as in, 2-3 total pages with 1-2 max MySQL queries on each page and some PHP), so bandwidth wouldn't be the issue, but sheer volume taking down the site would be the main concern. Cloud hosting seems like the best way to go, but would something like Amazon EC2, MediaTemple, or something else be the right choice in this case?

    Read the article

< Previous Page | 594 595 596 597 598 599 600 601 602 603 604 605  | Next Page >