Search Results

Search found 140 results on 6 pages for '2wire'.

Page 6/6 | < Previous Page | 2 3 4 5 6 

• VirtualBox VM running web server not accessible via external IP

  - by mwigdahl

  I have a Windows 7 machine running VirtualBox with an Ubuntu guest. The guest has a Bitnami LAMP stack installed. I have the guest configured for Bridged networking, and I can access the guest web server just fine from other machines on my LAN using the guest's IP. I'm trying to configure port forwarding so that I can access the web server from outside my LAN. (The router is a 2WIRE model as I'm on ATT's UVerse). I've set up port forwarding for ports 80 and 443 to the guest's IP in a similar manner to how I had them set up for my previous, physical web server, which worked just fine. However, I cannot seem to access the new, virtual web server using my external IP on the forwarded port. I suspected Windows Firewall issues on the host, but disabling it didn't solve the issue. Anyone have advice on what I should try next? EDIT: I've now attempted disabling the firewall on the guest with sudo ufw disable -- that doesn't seem to help either. However, after checking the router's port forwarding in more detail I may see the problem. My VM is named "linux" and in the router's configuration pages it shows up inconsistently. Sometimes it reports with a valid LAN IP and other times it doesn't show up with any IP. Even when it shows the correct IP the router indicates that it is disconnected. Could this be an indication that the 2WIRE router doesn't play well with VirtualBox's bridged networking mode?

  Read the article

• dnsmasq acts as the DHCP server for selected nodes overriding the existing DHCP server on the same LAN?

  - by user183394

  I am trying to set up a small "lab" at home. Like many modern homes, I have a regular DSL service which comes with a 2Wire 3600HGV router, which acts also as a DHCP server. Since I would like to PXE boot a few computers in my "lab" The 2Wire is inflexible to adjustments that I want to do I have used dnsmasq at work so I would like to use dnsmasq as the DHCP server for the few nodes in my "lab" if feasible. In the dnsmasq man page, there is the following: [...] -K, --dhcp-authoritative (IPv4 only) Should be set when dnsmasq is definitely the only DHCP server on a network. It changes the behaviour from strict RFC compliance so that DHCP requests on unknown leases from unknown hosts are not ignored. This allows new hosts to get a lease without a tedious timeout under all circumstances. It also allows dnsmasq to rebuild its lease database without each client needing to reacquire a lease, if the database is lost. [...] As far as I know, the ISC DHCP server can use the following to do what I would like to accomplish: authoritative; [...] subnet 192.168.1.0 netmask 255.255.255.0 { host nb0 { # only give DHCP information to this computer: hardware ethernet e8:9a:8f:17:70:42; fixed-address 192.168.1.10; option subnet-mask 255.255.255.0; option routers 192.168.1.254; option domain-name-servers 192.168.1.254; # Non-essential DHCP options filename "/pxelinux.0"; } [...] But I much prefer dnsmasq's "all-in-one-ness". My question: do I have to couple the -K option with something else? As shown in the example above, the ISC DHCP server requires the mac addresses of managed nodes to be explicitly specified. Does dnsmasq have something similar? FYI, the machine on which I plan to run dnsmasq runs CentOS 6.3 64bit. It has a statically assigned IP address: 192.168.1.3.

  Read the article

• Why can't I access my own web server from my local network?

  - by frenetic

  I have a web server in my home network and I'm using ZoneEdit for dynamic DNS. It's accessible perfectly to everyone outside of my local network, but since I switched to a Gateway 2Wire DSL modem/router I'm unable to use the domain to access the server from my network. I can access it via a local IP or by putting it in my Windows hosts file but this is annoying to do on every computer and for every subdomain. Any idea how I can fix this? Thanks!

  Read the article

• Why can't I access my own web server from my local network?

  - by frenetic

  I have a web server in my home network and I'm using ZoneEdit for dynamic DNS. It's accessible perfectly to everyone outside of my local network, but since I switched to a Gateway 2Wire DSL modem/router I'm unable to use the domain to access the server from my network. I can access it via a local IP or by putting it in my Windows hosts file but this is annoying to do on every computer and for every subdomain. Any idea how I can fix this? Thanks!

  Read the article

• ReadyNAS Duo - FTP home network connectivity issue

  - by dwabyick

  I have a ReadyNas Duo that I recently purchased and configured on my local home network. I'm an AT&T DSL subscriber using their default 2701HG-B Gateway (2Wire) wireless router. Basically, I have managed to configure my ReadyNAS, and can access HTTP shares and WINS shares just fine, but cannot get access to it via FTP. I've enabled it in the 'Standard File Protocols' section in the UI, and made a share have read/write default access via FTP. My settings: Port: 21 Authentication mode: User Allow upload resumes: Yes Passive ports: 1024-65535 Masquerade as: (empty, but I've tried the internal IP address). I've even poked around at my router, which has a firewall, and even tried to poke a hole for the 'FTP Server'app for the ReadyNAS. Doesn't seem like I should need to do this, or should. Any ideas what else to check? Thanks! -Daniel

  Read the article

• AT&T DSL 2701HG-B Modem, port forwarding to RealVNC

  - by Paula

  Our old cable modem could easily be set up to forward an "incoming port request" to the RealVNC software. Allowing us to log into our home computer from any location. We don't see any such configuration possiblity with our new AT&T DSL 2Wire 2701HG-B modem. (And it appears to have 2 entirely different 'set up screens'. Why?) Where is the screen that allows "forward incoming request for a certain port", to a certain computer, and direct it towards RealVNC"?

  Read the article

• Troubleshooting a slow database server with no load

  - by user1721724

  I'm getting ready to soft launch my website and I've run into some problems with what I think is being caused by my MySQL database running on Fedora. All websites run fine, just as I'd expect, but any pages that establish a database connection hang until the connection is established, and then bang, the site loads as it should. Ex. My landing page (http://www.thrusong.com) doesn't make a database connection and loads quickly. User profile pages (http://www.thrusong.com/john) make a database connection and load slowly, even though most of the data comes from memcached and the database currently has no load on it. This problem just came up yesterday when my router died and I began using my Pace 2Wire modem with built-in router. Before, my old router was set to handle everything. My ISP says the settings in the modem are correct. Any ideas? Thanks in advance.

  Read the article

• I have a wireless Canon P560 and my computer can't find it

  - by ed

  The printer is wireless and I haven't connected it via USB. I set the configurations for the Wi-Fi access point in the printer and it connected to my Wi-Fi. I have AT&T as the service provider and the 2Wire router. When I access the router in the browser I see that the printer is connected but when I run the software to detect the printer the computer can't find it. I have a Mac with Snow Leopard. I tried to detect the printer with another device and it can't find it. Is there a port that needs to be open for wireless printers? Because I tried putting the routers firewall settings for the device to its lowest and the computer still can't find it. Let me know. Thnx.

  Read the article

• RTL8192SU Linux Issue Installing Driver

  - by s32ialx

  OK I've read tons of fourms of people getting the onboard RTL8192SE working and the RTL8192SU working dif is U = USB they are both N and i have both Toshiba L500D-00T pre-installed Win Vistax64-HP and i have obtained the free Win7x64-HP upgrade the onboard wificard sucks and can't hold a stable connection for more then 20minutes in windows but the usb is amazing. Now problem is i tried both Ubuntu and Mandriva with no resolve the issue is the onboard drive detects and actually SHOWS that it's there but no wireless networks detect so it's saying no SSID's are broadcasting which i know is a lie since I'm running a 2wire bell dsl modem with built in wifi and a Linksys wrt54g w/ DD-WRT firmware and both are broadcasting fine. Why don't i use the USB? In the hardware device manager in mandriva it shows up as unknown but shows that it's realtek and that it's a 8192 chipset. but no option to for a driver install and when i do a make in terminal i get this error and no clue what it means [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# make make: *** /lib/modules/2.6.31.12-desktop-3mnb/build: No such file or directory. Stop. make: *** [all] Error 2 [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# any help appreciated. and just encase I'm running currently Mandriva Spring 2010 Free

  Read the article

• Using a Linksys Wireless- G Broadband Router for a Wireless Antenna/Adapter?

  - by Alex

  (Warning: I'm not too computer-smart). Just moved fm a home where I used ATT DSL to a home w/ Comcast Cable for internet. Old home had the DSL ethernet wired to my only desktop w/ a 2Wire router for my wireless signal for the laptops. In the new home the signal comes fm cable via a Netgear(300) wireless router (remotely located) & works fine for my laptops. After searching with the network software, my desktop (can't be ethernet wired cuz of location) detects no wireless signal. Desktop is a 2 yr old HP p6311f Pavilion (Windows 7). Can't seem to detect any wireless hardware (ant/adaptr). Maybe I don't have the ability & need to buy a USB wireless antenna? Would the Pavilion come w/ wireless capability out of the box, maybe something inside the tower? No antenna on back. I happen to have a Linksys Wireless router which I plugged in to the desktop (trying both internet & shared ports) & noticed signal action on the router front panel. No internet on desktop though. Can I use this as an antenna for the desktop? Thanks & sorry if my solution is an easy one I'm just missing. Just want internet on the desktop.

  Read the article

• RTL8192SU + RTL8191E Linux Issue Installing Driver

  - by s32ialx

  OK I've read tons of fourms of people getting the onboard RTL8191E working and the RTL8192SU working dif is U = USB they are both N and i have both Toshiba L500D-00T pre-installed Win Vistax64-HP and i have obtained the free Win7x64-HP upgrade the onboard wificard sucks and can't hold a stable connection for more then 20minutes in windows but the usb is amazing. Now problem is i tried both Ubuntu and Mandriva with no resolve the issue is the onboard drive detects and actually SHOWS that it's there but no wireless networks detect so it's saying no SSID's are broadcasting which i know is a lie since I'm running a 2wire bell dsl modem with built in wifi and a Linksys wrt54g w/ DD-WRT firmware and both are broadcasting fine. Why don't i use the USB? new in Mandriva Linux Control Center 2010.0 it shows up in Other/Unknown as RTL8191S WLAN Adapter and on the right pane this shows up Identification Vendor: ?Manufacturer Realtek Description: ?RTL8191S WLAN Adapter Media class: ? Connection Bus: ?USB Bus PCI #: ?1 PCI device #: ?5 Vendor ID: ?0x0bda Device ID: ?0x8172 Sub vendor ID: ?0x0000 Sub device ID: ?0x0000 Misc Module: ?rtl819xU In the hardware device manager in mandriva it shows up as unknown but shows that it's realtek and that it's a 8192 chipset. but no option to for a driver install and when i do a make in terminal i get this error and no clue what it means [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# make make: *** /lib/modules/2.6.31.12-desktop-3mnb/build: No such file or directory. Stop. make: *** [all] Error 2 [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# any help appreciated. and just encase I'm running currently Mandriva Spring 2010 Free

  Read the article

• Why does my router log crazy amounts of blocked traffic on port 1701?

  - by Vlad Seghete

  I have a 2701HGV-B 2Wire modem and router (AT&T). The log is basically full with entries similar to the following with a time between a fifth and a third of a second between entries: src=86.156.7.170 dst=xxx.xxx.xxx.38 ipprot=17 sport=6882 dport=1701 Unknown inbound session stopped src=58.176.22.252 dst=xxx.xxx.xxx.38 ipprot=17 sport=21573 dport=1701 Unknown inbound session stopped src=91.221.6.250 dst=xxx.xxx.xxx.38 ipprot=17 sport=25902 dport=1701 Unknown inbound session stopped ... where the source IP will be different for every entry. The entries accumulate constantly, every single second that the router is on several of them appear in the log. The destination is the WAN address for my router. I understand that this is somehow related to VNCs, but I don't know enough to figure out why my router is getting bombarded with requests for a VNC session. Is there anything fishy going on or is this normal? If it is normal, how do I keep these entries from spamming my log files? Since there's about two or three of them every second, everything else gets drowned out.

  Read the article

• Connection reset to some websites

  - by user143271

  I'm using a 2wire 3600HGV modem/router. Starting around this afternoon, any time I try to access anything from i.imgur.com I get The connection to i.imgur.com was interrupted in chrome, and the actual error is Error 101 (net::ERR_CONNECTION_RESET). It's network wide (tested multiple browsers on multiple computers and phones). I can access imgur.com just fine, but nothing from its content server i.imgur.com. If I disable wifi on my phone and use its 4G connection, I can access it just fine, so obviously imgur isn't down. I haven't changed any configuration on the router, and I have tried changing DNS servers (I tried google and OpenDNS). It also seems that imgur is not the only site; howtogeek and a couple of others seem to have the same problem. It looks like they are all edgecast cdn content servers, but not all edgecast cdn servers fail. Tumblr, for instance, works just fine. Does anyone have any idea what would be causing this? EDIT: Related to the edgecast remark, it would appear that this is a specific edgecast server: gs1.wpc.edgecastcdn.net. Tumbler's content is on gs1.wac.edgecastcdn.net, so it might be on a different server. Edit #2: These sites all respond to ping just fine as well.

  Read the article

• Intermittent internet access on a flat network - Router is connected

  - by Naveed

  I’m looking for some help with network settings. I’ve just started a new job (non-IT!) and we have problems with our office network. I’m the most IT literate in the organisation (15 permanent employees) and so have been dealing with IT issues. Our main bit of software is web-based so we need constant web access but it sometimes goes down for between 20 minutes and 3 hours despite everything seemingly working fine. It’s a flat network with wireless APs, BT Business Broadband 8Mbit connection and that’s about it. We have no servers and no standard settings and staff are encouraged to bring in their own laptops and connect! The network basically exists to provide internet access and that’s it. We also have students accessing the wireless (and I know there’s a whole list of access and content issues etc but right now we just need internet access stabilised). This is what we have: Building 1 Cisco SLM-224P 24-port PoE 10/100 switch with 2 gigabit ports 3 x ZyXEL NWA-3160 wireless APs Samsung OfficeServ 7100 phone server which borrows the building’s wiring Building 2 Netgear GS605-UK 5-port 10/100/1000 switch 1 x ZyXEL NWA-3160 wireless AP 1 x BT Business Hub – 2wire BT2700hgv – is the DHCP server We have 2 link cables between the buildings. One connects the two switches on a gigabit port. The second (oddly) connects the switch in building 2 to the OfficeServ server in building 1. When the internet goes down I can still access the router through a wireless connection. I can also ping websites and get a response. Firefox just says “Cannot connect” etc. The system then heals itself when it feels like it. (Sorry if this is asking too much but) These are my immediate questions… Why would browser-based internet go down? I don’t know enough about protocols etc but I can try to standardise settings. The WAPs have a DNS server setting and I don’t know whether it should be “None” or “From DHCP”. What should be the DHCP server? The router or the Cisco switch? Or something else?! Would there be any problem in connecting the second link from switch to switch? Is that good practice? Is it worth swapping the Netgear GS605 with either a Cisco SG200-08 or Netgear GS108T-200? Is it worth upgrading the router to, for instance, a Cisco RV042G Dual Gigabit router which would also act as a switch? Or is it better to have a separate router and switch in Building 2?

  Read the article

• Routing a PPTP client and VMware Server instance running on the same box

  - by servermanfail

  I have a Windows 2003 SBS box. It has 2 physical NIC's: WAN and LAN. The WAN is a public IP. The LAN is a simple 192.168.2.x subnet with Microsoft DHCP Server. Microsoft Routing and Remote Access Service is used to provide NAT to LAN. The box also runs VMware Server with a virtual machine running Windows XP. I want people to be able to VPN into the box, and connect to these virtual machines on the MSRDP port. I can VPN (PPTP) into the 2003 SBS box fine, as well as ping other machines on the LAN. I can ping the VM from a physical workstation on the LAN and vice-versa. I can ping the VPN client from the a physical workstation on the LAN and vice-versa. I can ping the VPN client from the Server console and vice-versa. I can ping the VM client from the Server console and vice-versa. But I cannot ping the VPN client from the VM and vice-versa. I was hoping to set up 2 or 3 Windows XP virtual machines on our only server, so that a couple of people can remote in to work without having to leave a physical machine on in the office. You could this attempted set up a "poor mans terminal server". On the 2003 SBS Server:- C:\Documents and Settings\Administrator>route print IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 50 56 c0 00 08 ...... VMware Virtual Ethernet Adapter for VMnet8 0x3 ...00 50 56 c0 00 01 ...... VMware Virtual Ethernet Adapter for VMnet1 0x10004 ...00 53 45 00 00 00 ...... WAN (PPP/SLIP) Interface 0x10005 ...00 11 43 d4 69 13 ...... Broadcom NetXtreme Gigabit Ethernet 0x10006 ...00 11 43 d4 69 14 ...... Broadcom NetXtreme Gigabit Ethernet #2 =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 81.123.144.22 81.123.144.21 1 81.123.144.20 255.255.255.252 81.123.144.21 81.123.144.21 1 81.123.144.21 255.255.255.255 127.0.0.1 127.0.0.1 1 81.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 86.135.78.235 255.255.255.255 81.123.144.22 81.123.144.21 1 109.152.62.236 255.255.255.255 81.123.144.22 81.123.144.21 1 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.2.0 255.255.255.0 192.168.2.3 192.168.2.3 1 192.168.2.3 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.26 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.28 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.32 255.255.255.255 127.0.0.1 127.0.0.1 50 192.168.2.50 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.255 255.255.255.255 192.168.2.3 192.168.2.3 1 192.168.10.0 255.255.255.0 192.168.10.1 192.168.10.1 20 192.168.10.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.10.255 255.255.255.255 192.168.10.1 192.168.10.1 20 192.168.96.0 255.255.255.0 192.168.96.1 192.168.96.1 20 192.168.96.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.96.255 255.255.255.255 192.168.96.1 192.168.96.1 20 224.0.0.0 240.0.0.0 81.123.144.21 81.123.144.21 1 224.0.0.0 240.0.0.0 192.168.2.3 192.168.2.3 1 224.0.0.0 240.0.0.0 192.168.10.1 192.168.10.1 20 224.0.0.0 240.0.0.0 192.168.96.1 192.168.96.1 20 255.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 255.255.255.255 255.255.255.255 192.168.2.3 192.168.2.3 1 255.255.255.255 255.255.255.255 192.168.10.1 192.168.10.1 1 255.255.255.255 255.255.255.255 192.168.96.1 192.168.96.1 1 Default Gateway: 81.123.144.22 =========================================================================== Persistent Routes: None C:\Documents and Settings\Administrator>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : 2003server Primary Dns Suffix . . . . . . . : mycompany.local Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : Yes WINS Proxy Enabled. . . . . . . . : Yes DNS Suffix Search List. . . . . . : mycompany.local gateway.2wire.net Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 8 Physical Address. . . . . . . . . : 00-50-56-C0-00-08 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.10.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 1 Physical Address. . . . . . . . . : 00-50-56-C0-00-01 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.96.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : PPP adapter RAS Server (Dial In) Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface Physical Address. . . . . . . . . : 00-53-45-00-00-00 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.32 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter LAN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet Physical Address. . . . . . . . . : 00-11-43-D4-69-13 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.50 Subnet Mask . . . . . . . . . . . : 255.255.255.0 IP Address. . . . . . . . . . . . : 192.168.2.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.2.3 Primary WINS Server . . . . . . . : 192.168.2.3 Ethernet adapter WAN: Connection-specific DNS Suffix . : gateway.2wire.net Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet #2 Physical Address. . . . . . . . . : 00-11-43-D4-69-14 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 81.123.144.21 Subnet Mask . . . . . . . . . . . : 255.255.255.252 Default Gateway . . . . . . . . . : 81.123.144.22 DHCP Server . . . . . . . . . . . : 10.0.0.1 DNS Servers . . . . . . . . . . . : 10.0.0.1 Primary WINS Server . . . . . . . : 192.168.2.3 NetBIOS over Tcpip. . . . . . . . : Disabled Lease Obtained. . . . . . . . . . : 25 February 2011 22:56:59 Lease Expires . . . . . . . . . . : 25 February 2011 23:06:59 C:\Documents and Settings\Administrator>ping 192.168.2.11 Pinging 192.168.2.11 with 32 bytes of data: Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128

  Read the article

< Previous Page | 2 3 4 5 6