Search Results

Search found 5389 results on 216 pages for 'bridge router'.

Page 6/216 | < Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >

• SOHO NETGEAR wireless router disconnects when downloading torrents

  - by Lirik

  I have a NETGEAR WGT624 wireless router at home which dies when there is a heavy torrent load. I open up my torrent client and it downloads for about 5 to 10 minutes and it continues to increase the number of seeds (goes up to 70-80 seeds), but after that the router simply fails and I have to restart it in order to get an internet connection again. When I connect directly via an ethernet cable the router and open up the torrent client, then it seems to be doing fine, but when I go wireless then the router stops working properly (although all the lights are still blinking as normal). Is there any way that I can fix this? New router firmware? Change some router options? Feed it a cookie? Anything?

  Read the article

• Setting up a router as a DNS server only

  - by Jacob R

  I have a Linksys WRT54GL router that I don't need anymore, since I had to buy a 3G capable router (Dovado 3GN). As I only have a 3G connection at home, I want to optimize it as much as possible. I want to setup a caching DNS server, including some blacklisting of ad domains. The router currently runs the DD-WRT firmware. Is it possible to use this router as an ordinary computer, running only a DNS server, disabling all other features such as DHCP, WLAN, etc? Connecting it to my other router, should I simply run a cable into the WAN-port of the Linksys router?

  Read the article

• Setting up a router as a DNS server only

  - by Jacob R

  I have a Linksys WRT54GL router that I don't need anymore, since I had to buy a 3G capable router (Dovado 3GN). As I only have a 3G connection at home, I want to optimize it as much as possible. I want to setup a caching DNS server, including some blacklisting of ad domains. The router currently runs the DD-WRT firmware. Is it possible to use this router as an ordinary computer, running only a DNS server, disabling all other features such as DHCP, WLAN, etc? Connecting it to my other router, should I simply run a cable into the WAN-port of the Linksys router?

  Read the article

• DCHP and Router load testing

  - by John H

  I manage a campground wifi network with an average of 10 - 60 active users. I have encountered issues where the router starts acting flaky (failing to assign DHCP or failing to pass traffic) without any clear warning (low cpu utilization, etc). I upgraded the router a couple times and ended up with a Netgear ProSafe VPN router that seems to be handling the traffic. The interesting thing is that the Netgear has lower specs than the Buffalo router it replaced, indicating the issue is with the DD-WRT firmware. While I'll be pursuing this issue on the dd-wrt forums, I need a way to test routers. My vision is having 1-2 computers connected on the LAN side and 1-2 computers connected on the WAN side. I want the LAN computers to be generating various type of traffic and connections, as well as requesting DCHP addresses. A few notes: The wireless aspect should be a non-issue. Most clients would connect to a wireless bridge and come into the router through a network cable. I had a monitoring server with Nagios running check_dhcp against the router. This server was connected directly by a network cable, eliminating wifi bridges and other devices from the equation. This question is somewhat related, but not exactly: Load testing wireless LANs I am going to look at IxChariot. While I'd ideally like to use a 1 computer on each side running Linux and preferably free software, I can entertain running Windows, multiple computers, or non-free software. Total bandwidth doesn't seem to be the issue. I can transfer large files all day. Even on the busiest days, the users seemed to only pull ~5Mbps. There is very little "LAN to LAN traffic" and most of it might never have reached the main router. The issue I need to test for seems to be tied to active users, or more appropriately, active sessions. I know active users or active clients is a meaningless term from a router standpoint and wouldn't mind having more appropriate terms to use. Summary: I need a way to test a routers ability in handling traffic from a large number of clients. My current strategy is to purchase a router, deploy it, and see how it fails in the live environment.

  Read the article

• Access my router's gateway network?

  - by Danpe

  I have 2 routers in my place. Main Router (Connected to the Internet) - 192.168.1.1 Secondery Router (Connected to the Main Router) - 192.168.0.1 I have a Network Storage Device and few Shared Directorys connected to the Main Router. (Network Storage - 192.168.1.16) How can i acces one of them using a PC connected to the Secondery Router? Home Network Diagram: I currently have access to the internet using both laptop and Main PC. But i want to get access from my laptop to the Storage and to ym shared directorys. The problem is the my Main router always forwards all packets stright to the WAN.. (Internet)

  Read the article

• configure HTTPS server on a cisco router

  - by Sara

  For the past week I was trying to configure an HTTPS server on a cisco 2900 router, I've used the following commands and assigned a username and password to privilege 15 however, when Im trying to access a given ip it requires a username and password however when I insert the username and password I configured it does not allow me to enter and i'm not sure where the problem is. Router(config)# ip http secure-server Router(config)# ip http authentication local These were the commands i used for the https server and also I used the following to assign the username and password Router(config)#username name privilege 15 secret 0 password where 'name' and 'password' represent the username and password respectively I'm trying to access the 192.168.14.1 interface on the router and the username and password i created are not authorized to enter (I got the commands from a cisco router manual)

  Read the article

• Ping Flooding in router log

  - by Freeman

  I've had recently a period of repeated disconnections from my router with connection problems. I checked my router log I found several Ping Flooding entries all originating from the IP 69.171.227.232 which turned out to be one of Facebook IPs! I'm wondering what does that means? Can Facebook chat cause such a condition? My router is DLink dir 600 and the condition that devices were disconnected from router, not router from internet.. Connection is WAN And how to solve this router problem?? My wifi clients were about 3-5 at that time..

  Read the article

• Lynksys WRT120N wireless router not connecting to ADSL

  - by pradeetp

  I have a lynksys WRT120N wireless router that was connected to Sterlite ADSL modem. The internet connection was working fine through wireless access. I changed the ADSL router because it developed some power issues and got it replaced with the same model/brand from the service provider. However I am not able to access internet now. Here is the current setting Sterlite SAM300 XA IP Address: 192.168.2.1 (I changed it to this IP because the IP address of my ADSL router was same) Lynksys WRT120N wireless router IP Address: 192.168.1.1 If I connect my laptop to ADSL router directly, the internet works fine. It is only that that if I access it wirelessley through wireless router that I am not able to connect to internet. The IP address setting has been configured to obtain IP address automatically. I have windows 7 OS home edition. Could someone please help me to fix this issue.

  Read the article

• Would a switch be covered by a router's firewall

  - by Uh-yeah...

  So... Hopefully; this is the right place for this question. I need more Ethernet ports on my home network. Sadly, we already have an old router connected to the main router and we still need more ports. I feel dumb for asking; but, I just would like to double check. Would the devices connected to the switch be "protected" by the Main router's firewall? ? Up to this point I have assumed that was the case; but, a co-worker is convinced that is not the case [ I believe he is thinking of a situation in which the switch (un-managed) is before an access point]. [It would go modem to main router; main router then has the switch and old router connected to it.

  Read the article

• Ubuntu Laptop as a wireless hotspot on bridge mode

  - by nixnotwin

  I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

  Read the article

• Ubuntu Laptop as a wireless hotspot on bridge mode

  - by nixnotwin

  I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

  Read the article

• getting Internet connection sharing working in a slightly more complicated configuration

  - by tirichitirca t

  I have the following configuration: Computer A - Mac OSX 10.8.4, wireless & wired adapters Computer B - Windows 7 (64 bit), wireless & wired adapters, has internet connection via the wired adapter (ethernet) d-link wired/wireless router. Problem to solve: Connect from computer A to the internet through the wired connection of computer B. I tried the following: I set up a local network between A and B using the d-link router. The configuration is this: D-link router - 192.168.0.1 A - wired connection to the d-link router, static 192.168.0.101 (I could have used the wireless but I preferred the wired connection) B - wireless connection to the d-link router DHCP 192.168.0.102 (but I made sure it always gets the same address) B - wired connection to the internet using some address that begins with 10.x.y.z. In this configuration A can see B. I enabled ICS on the wired adapter of B. I set up the Gateway of A to point to B and DNS servers to point to the DNS servers specified for the 10.x.y.z address. It doesn't work, A goes only as far as B. It can ping the 10.x.y.z address of B though. I then found this article: http://terrybritton.com/windows-internet-connection-sharing-ics-not-working-with-linux-bridging-is-the-solution-916/. Terry is suggesting that a bridge should be defined on B between the two connections. I tried that but basically computer B is screwed as soon as I create the bridge. It can't connect to the internet anymore. It is as if the network bridge seems to think the traffic to the internet should go from the wired connection to the wireless and not the other way around. The other thing that puzzles me is the router itself. In general the router needs an internet address. In a normal configuration it is the router that gets the ip address and the internet traffic goes through the router. In my case I am not interested in that. So, any suggestions to get this working? I wouldn't shy away from using a commercial software but I would think windows 7 should allow me to do it. Thanks

  Read the article

• What device can create wireless network while connecting to an ethernet router

  - by Nicolo

  Hi, I have access to an ethernet port of a wireless router. I simply connect my laptop to it via an ethernet cable. There are a total of four such ports on the wireless router. Now I want to connect a device (a wireless access point? wireless bridge? wireless switch?) via an ethernet cable to one of the other ethernet ports of the router. I want this device to act as a kind of wireless switch - it should "split" the ethernet connection coming from the router to two or more computers that connect to this device via a wireless. Basically, I have a wireless router with its wireless function switched off. I don't know the password for that router so can't activate the wireless function. Don't know the password of the ISP either. The only thing I can do is to connect via ethernet cable to the wireless router and this does not require a password. Now I want to use that connection and build a wireless upon it. What kind of device do I need? I am not really very well informed about network management and find the descriptions "wireless access point", "wireless bridge", "wireless switch" confusing. I know what an ethernet switch is - what I need is a device which would do the same but by allowing the clients to connect to it via a wireless. What kind of device would do that? Any recommendations about specific products?

  Read the article

• why adding router will hide all share folders

  - by user1285419

  I have several computers running winxp installed in my office, they are all connecting to the WAN providing by the building (wall socket) (DHCP, mask 255.255.252.0). I setup a shared folder in my computer so all other computer in the same group could access it. This configuration have been using for long time. Recently, I am trying to setup a router. I have the WAN port of the router go to the wall socket, connect the NIC to the LAN port of the router, setup the router in DHCP mode (192.168.0.100/255.255.255.0 to 192.168.0.110 /255.255.255.0), I turn off all the firewall (windows one and router's builtin one), the NIC has ip set as DHCP. If I ipconfig/all, I see that the NIC was assigned ip 192.168.0.100. I can access the internal, email whatever. However, the shared folder can no longer be accessed by other computers in the same group. I think it is the problem of ip. But what's really weird is if I turn off the DHCP function in the router, ipconfig/all always give 0.0.0.0/255.255.255.255 and I cannot access the internet. I have no idea what's going on. Anyone know how to fix it and allow the shared folder in application of router? Thanks.

  Read the article

• Router startup problems

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the power off and on again it all works. I also have to restart my PC too in order for everything to work. How can I solve this problem? Just leave the router turned on all time? I prefer a daily IP switch, though. May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• Router startup problems

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the power off and on again it all works. I also have to restart my PC too in order for everything to work. How can I solve this problem? Just leave the router turned on all time? I prefer a daily IP switch, though. May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• Connecting to my home router web interface from work

  - by Joe

  Hi, I'm trying to connect to my home router web interface from work. I use dyndns, because I don't have a static IP at home, and it works perfectly from any other place except my workplace (update: I made a mistake, see edit below). When trying to access the web interface from work I get a "500 Server Error" with the code: SERVER_RESPONSE_RESET. I'm not trying to use any protocols such as remote desktop, I'm only trying to access the web interface. I can access any other web page from my workplace with no problems, and I think my router web interface is like any other web page, isn't it? I thought maybe my work place proxy blocks addresses of services like dyndns, so I also applied another trick. Since I have a web page on my own domain (say www.mydomain.com) which I can access from work, I tried adding a CNAME to my domain which is linked to the dyndns address (router.mydomain.com). This way if anyone enters the address router.mydomain.com from anywhere, they reach my home router web interface, and there's no way of knowing it's a dyndns address (or is there?). However, it still doesn't work from my workplace (I get the same error message). Any ides? Edit: I'm sorry to say I made a mistake earlier. I used to be able to access my home router web interface from my old workplace, and I thought it was still possible since I don't recall making any configuration changes. However, after reading the replies, I went over to my old workplace and checked, and it doesn't work from there either. I'm very sorry for giving out wrong and misleading information about my problem. So to summarize: my problem is that I can't access my home router web interface from anywhere.

  Read the article

• Router startup problem

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the pow*emphasized text*er off and on again it all works. The problem is regarding startup only, when I get it to work everything runs as smooth as a 1980-s text-based C++ game on a 3ghz machine. I also have to restart my PC too in order for everything to work. - How can I solve this problem? - Just leave the router turned on all time? I prefer a daily IP switch, though. - May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• Unusable network, packet losses between router and NIC

  - by KáGé

  I have this setup: Gigabyte P35-DS3P motherboard Asus NX1101 PCI network card (the one on the motherboard got fried a few years ago by a power surge) Asus RT-N16 router Windows 7 x64 I think the other specs are irrelevant here, but I'll post them if you say so. Until a week ago everything was fine, but then my network became unusable: websites start loading but timeout before anything would come through (true for the web interface of the router as well), I can't reach the computer from my notebook and Windows' ping utility measures a ~50% packet loss between the computer and the router. Pinging localhost is good. The router works completely fine when wired to my notebook. I also tested different ports on the router, different cables, different router and connecting directly to the modem, but it's still the same. Sometimes it works for a few minutes right after turning on the machine, but then it becomes crap again, but mostly it's useless from the start. I've tried updating the firmware on the router, updating the driver for the network card (after which I started getting BSoDs in every 15 minutes), reinstalling Windows, swapping to Fedora 15 but none of them changed anything. Does this mean that the network card is dying, or could it be something else? If it's the card, what model do you recommend as a replacement? (Could be PCI or PCI-Ex x1) Thanks for your help.

  Read the article

• HP MSR 30-10a Router - Route Traffic over Default Route

  - by SteadH

  We have a brand new HP MSR 30-10a Router. We have a fairly simple routing situation - we have two IP blocks, one which has a route out. We need things on the first block to go through the router, and out. I have an old Cisco 2801 router doing the job right now. For our example - IP Block 1: 50.203.110.232/29, Router interface on this block is 50.203.110.237, route out is 50.203.110.233. IP Block 2: 50.202.219.1/27, Router interface on this block at 50.202.219.20. I have a static route created for: 0.0.0.0 0.0.0.0 50.203.110.233 The router seems to understand this. When on the CLI via serial cable, I can ping 8.8.8.8 and hear responses from Google DNS. Woo hoo! The issue arrives when any client sits on the IP Block 2 side. I configured my client with a static IP of 50.202.219.15/27, default gateway 50.202.219.20. I can ping myself. I can ping the near side of the router (50.202.219.20), and I can ping the far side of the router (50.203.110.237. I cannot ping anything else in IP block 1, nor can I ping 8.8.8.8. Here is my configuration file: <HP>display current-configuration # version 5.20.106, Release 2507, Standard # sysname HP # domain default enable system # dar p2p signature-file flash:/p2p_default.mtd # port-security enable # undo ip http enable # password-recovery enable # vlan 1 # domain system access-limit disable state active idle-cut disable self-service-url disable # user-group system group-attribute allow-guest # local-user admin password cipher $c$3$40gC1cxf/wIJNa1ufFPJsjKAof+QP5aV authorization-attribute level 3 service-type telnet # cwmp undo cwmp enable # interface Aux0 async mode flow link-protocol ppp # interface Cellular0/0 async mode protocol link-protocol ppp # interface Ethernet0/0 port link-mode route ip address 50.203.110.237 255.255.255.248 # interface Ethernet0/1 port link-mode route ip address 50.202.219.20 255.255.255.224 # interface NULL0 # ip route-static 0.0.0.0 0.0.0.0 50.203.110.233 permanent # load xml-configuration # load tr069-configuration # user-interface tty 12 user-interface aux 0 user-interface vty 0 4 authentication-mode scheme # My guess right now is there is some sort of "permission" needed to use the default route. The manuals haven't turned up a lot in this area that don't make the situation much more complicated (but maybe it needs to be more complicated?) Background: we use HP switches, and I love the CLI. I bought HP thinking the command line interface would be similar, or at least speak the same language. Whoops! I'd be happy to provide more information or perform any additional tests. Thanks in advance! Update 1: The manual mentions routing rules. I hadn't previously added these (since our Cisco 2801 seems to route anything by default). I added: ip ip-prefix 1 permit 0.0.0.0 0 less-equal 32 alas, still no dice.

  Read the article

• linux router setup

  - by nuttsduh

  Hi All, I a trying to setup a a linux router for the first time and i am struggling with the setup. Here how i want to setup it up: ISP line - Linux router - Linksys router - Lan. Linux router has eth0 and eth1 How do i setup this and where do i put my external ip? Many thanks,

  Read the article

• Mac has IP address, can connect to router but can't connect outside

  - by partition

  Weird problem, my MacBook can't connect anywhere right now! The router works, it gets an IP, it can log into to the router but it can't resolve anything! The router works as I connected another device to it and it connected to the net. The MacBook doesn't have any strange DNS configurations either, just 192.168.1.1 for the router I even tried tethering it to my phone, and it still would not connect to the net... help?

  Read the article

• Why do I see router and not my real IIS?

  - by Tim Tom

  I am trying to access IIS through web but unable to do so. Basically I have a router (which functions as router and modem) that is given by ISP and I have another router connected to the router given by ISP. My ISP's router can be visited through 192.168.0.1 and the router that I connected to ISP's router can be visited through 192.168.1.1 Please see my ISP's router: As you can see I have DMZ enabled for my router of 192.168.1.1 Now please see my router of 192.168.1.1: As you can see I added a virtual server for port 80 where 192.168.1.125 is my private IP. I rebooted both of my modems an tried to visit my IP from: http://www.whatsmyip.org/ and after doing so, when I type my live IP I still see my router of 192.168.0.1 instead of my IIS. What am I missing? Note: I have disabled Firewall on both of the routers. Any help would be appreciated.

  Read the article

• Why do I see router and not my real IIS?

  - by Tim Tom

  I am trying to access IIS through web but unable to do so. Basically I have a router (which functions as router and modem) that is given by ISP and I have another router connected to the router given by ISP. My ISP's router can be visited through 192.168.0.1 and the router that I connected to ISP's router can be visited through 192.168.1.1 Please see my ISP's router: As you can see I have DMZ enabled for my router of 192.168.1.1 Now please see my router of 192.168.1.1: As you can see I added a virtual server for port 80 where 192.168.1.125 is my private IP. I rebooted both of my modems an tried to visit my IP from: http://www.whatsmyip.org/ and after doing so, when I type my live IP I still see my router of 192.168.0.1 instead of my IIS. What am I missing? Note: I have disabled Firewall on both of the routers. Any help would be appreciated.

  Read the article

• Linux VLAN Bridge

  - by raspi

  I have home network with VLANs, one for LAN, one for WLAN and one for internet. I'd like to use bridging so that instead of configuring these same VLANs to every machine, they had own VLAN ID and bridges were LAN, WLAN and internet. I've tried it but for some reason keep-alive/ttl seems to get broken because SSH sessions etc suddenly disconnects. We have this same setup working in workplace for 4+ years with 100+ customers but it's custom firewall/router hardware so accessing it is impossible. I know that it runs Linux. So what is Debian/Ubuntu default network settings doing wrong or is it just NIC driver/hw problem? I've tried to mess araund with ttl etc settings without any luck. The bad stuff is happening in the bridge because current VLAN-only setup works fine. interfaces: auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 allow-hotplug eth1 iface eth0 inet static iface eth1 inet static auto vlan111 auto vlan222 auto vlan333 auto vlan444 auto br0 auto br1 auto br2 # LAN iface vlan111 inet static vlan_raw_device eth0 # WLAN iface vlan222 inet static vlan_raw_device eth0 # ADSL Modem iface vlan333 inet static vlan_raw_device eth1 # Internet iface vlan444 inet static vlan_raw_device eth0 # LAN bridge iface br0 inet static address 192.168.0.1 netmask 255.255.255.0 bridge_ports eth0.111 bridge_stp on # Internet bridge iface br1 inet static address x.x.x.x netmask x.x.x.x gateway x.x.x.x bridge_ports eth1.333 eth0.444 bridge_stp on post-up iptables -t nat -A POSTROUTING -o br1 -j MASQUERADE pre-down iptables -t nat -D POSTROUTING -o br1 -j MASQUERADE # WLAN bridge iface br2 inet static address 192.168.1.1 netmask 255.255.255.0 bridge_ports eth0.222 bridge_stp on Sysctl: net.ipv4.conf.default.forwarding=1

  Read the article

< Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >