Search Results

Search found 148 results on 6 pages for 'cord blomquist'.

Page 6/6 | < Previous Page | 2 3 4 5 6 

• "Ethernet" doesn't have a valid IP configuration

  - by Xuzuno

  I'm using an ethernet cord to connect to my internet and it has been working well until Thursday morning when I turned on my laptop (Windows 8) to see a yellow triangle sign in the bottom right hand corner, in front of the ethernet connected symbol. Since then I haven't been able been able to access the internet from my computer. When I hover over it, it says that it is an "Unidentified network" and there is "No internet access". I've run the Windows 8 troubleshooting and it says that the problem found was ""Ethernet" doesn't have a valid IP configuration", but I'm unsure how to fix it. I'm thinking that the problem is to do with my computer rather than my network, because I've tried another laptop (Windows 7) through the same ethernet cable and connection and the internet works fine on the other laptop. I've tried so many fixes that I've found online, with none of them actually working. Yesterday I even tried a full system reset, where I re-installed Windows 8, re-partitioned and wiped everything off the hard drive, but it still appears have the exact same problem. Today I also purchased and tried a new ethernet cable which didn't work, so I then purchased a USB to Ethernet adapter, to make sure that it wasn't my ethernet port on my laptop that was faulty. That didn't work either, and the same problem still remains. I feel like I've tried everything, so can someone please help me?

  Read the article

• ASUS laptop doesn't charge/use the battery after reinstalling Windows 7

  - by Stan

  I've done a clean install of Windows 7 x64 on an ASUS X501A laptop. The battery is detected and shows in the system tray as "plugged in, charging". However the charge level stays at 76% and if the AC cord is plugged out the laptop turns off. The laptop does not turn on without being plugged in either. Everything worked perfectly prior to reinstall. I've tried: Downloading and installing all the ASUS drivers, including the ATK ACPI driver Checking the BIOS - there do not seem to be any battery-related settings Flashing the BIOS to the latest version Uninstalling Microsoft ACPI-Compliant Control Method Battery in device manager as suggested on the internet Full power discharge/ATX reset as suggested by ASUS support: remove mains power charger, remove battery, press and hold power button for 10 seconds, reconnect battery and mains and turn on I have a feeling all this may have something to do with the EFI BIOS that comes on the laptop. During the reinstall I had to delete all partitions and start anew, because the Windows installer complained about the improper order of GPT partitions. The EFI System Partition was recreated by the installer, and I am guessing that it may be missing the particular ACPI driver needed to make the battery work. I've tried researching this, but could not come up with any useful info. I am hoping someone here may know a bit more about this and maybe help me understand what's going on and how to fix it. Barring that, I'll have to re-image the drive off an identical ASUS laptop with stock install and hope it fixes things.

  Read the article

• Computer Won't Boot Properly, unless in safe mode?

  - by Mr_CryptoPrime

  I bought a computer today and booted it up, but when I did I only got a blank screen. I checked to make sure it wasn't the monitor by connecting it to my old computer...it worked. I then tried connecting my monitor to both DVI ports and found that the bottom one did work. However, now it just boots up and says "loading windows" and then when the login screen is suppose to come up the screen just goes blank and monitor says "no input, check cord" (or something like that). I tried reinstalling windows and then I was able to log on normally. I used the CD's and reinstalled all the drivers, then rebooted...now I am stuck right back where I started. I tried taking out the RAM and inserting into different slots, that didn't fix anything. I was able to boot up into windows using safe-mode. I suspected that my ATI Radeon 6950 was the issue and downloaded the drivers, but I can't install them on safe-mode. Someone said to install C++ distr. and I tried doing that to fix driver installation problem of "failed to load detection driver" but it wouldn't let me do that either. Please someone help me, I don't want to have to deal with the evil redtape of sending it back to get a replacement! My computer: -Content--text-_-"http://www.newegg.com/Product/Product.aspx?Item=N82E16883229236&nm_mc=TEMC-RMA-Approvel&cm_mmc=TEMC-RMA-Approvel--Content--text-_- Driver detection problem: http://www.hardwareheaven.com/hardwareheaven-tools-discussion/174912-failed-load-detection-driver-installation-error.html Driver download page: http://sites.amd.com/us/game/downloads/Pages/radeon_win7-64.aspx#1 I am using windows 7. Thanks again.

  Read the article

• My Hard Drive isn't Working

  - by MeCB

  I never use Safely Remove Hardware with Windows XP. It has been working for me for years with my SD card, mouse, hard drive and memory stick. My hard drive has a USB cable and power cord so I can hook it up to any desktop hard drive. Now my hard drives don't like this and I did not know this till now. I am always careful and to wait till it is all finish accessing the USB before I unplug it. Now three of my hard drives can't be seen by Windows, though the others still work. when I hook it up to another computer it works fine. I use the same USB cable to hook up all of my hard drives one at a time. So my USB cable is good. I think that when I unplugged the hard drive this one time, it had a file it still wanted to see and now only this drive does not work only this computer. Then the same thing happens to my other two hard drive after I used it for a week with the same cables. How can I fix this?

  Read the article

• Ethernet cable unplugged after updating from windows 8.0 to 8.1

  - by Pehmolelu

  Yeah, so I went and updated my windows 8 pro to 8.1. Now everything else seems to work but the network. The Ethernet just says that Network cable is unplugged, even though it is plugged and I have tried different cord as well and I have tested that the router works. I have tried uninstalling the network drivers (Realtec PCIe GBE) and reinstall them with no success. After installing drivers the Device Management gives error for it "Device could not be started. Code 10" Before 8.1 update I had rt630x64.inf, after update it was netrt630x64.inf, and after installing the latest driver rt630x64.inf. With rt630x64.inf there isn't any error, but it's still not just working. New downloaded version: 8.020.0815.2013 (From Realtek website) The driver before: 8.1.510.2013 (After updating the windows to 8.1) I'm using Desktop PC, no VM. I dont have VirtualBox or Vmware installed. I have checked from BIOS that the card is enabled. I have booted in safe mode with network enabled. Says unplugged there as well. I have put the power off for few minutes and put back on, no effect. If anyone has any kind of suggestions, please tell.

  Read the article

• Nvidia 9800GT randomly prevents computer from booting

  - by Blender

  My computer has been running Windows and Linux perfectly fine with my 9800GT for the past year or so, but today it refused to boot. When I press the power button, this is what happens: Power button flashes once. Fans whir. Graphics card makes clicking noise. Computer reboots. Go back to 1. The cycle just keeps going, and I have to yank the cord to make the computer stop. After about 30 attempts at booting it, the computer powers on and everything works. I'm pretty sure that the graphics card isn't malfunctioning, as I've been GPU computing on it for a while now without any hiccups. But the strange thing is, the computer boots perfectly fine in only 5 boots if I remove the card. The computer is a HP Pavilion a6028x Desktop PC: Processor: AMD Athlon 64 X2 (W) 4600+ 2.4 GHz (AM2 socket) Motherboard: ECS MCP61PM-HM (Nettle 1) RAM: 3GB DDR2 (two different brands) More specs here Does anybody know what could be the problem? Any help or information would be greatly appreciated!

  Read the article

• Connect from Mac OS X to Windows 7 Desktop

  - by jrn

  I am trying to connect from my MacBook to my Windows 7 machine within my own network - if it will work from outside my network that's a plus but no need to have. My Windows 7 machine is freshly installed with Windows 7 Home Premium. It runs the built-in firewall with no settings changed so far as well as Microsoft Security Essentials. So far I tried CoRD and Microsofts Remote Desktop Connections to connect from my Mac to my Windows machine without any success. I did try and disabled the firewall on my Windows machine but could not connect either. The reason I did this was to check wether there is a Windows firewall setting preventing me from connecting. On top of that I manually started the Remote Desktop Services and Remote Desktop Configuration within services.msc. Is there anything else I have to enable for a remote desktop connection? Could there be any router setting I have to tweak? Since I do not want to connect from outside my own network I thought I don't have to do any port forwarding. The error messages I retrieve are all connection timeouts. I can however ping the hostname and/or IP address. Any help would be greatly appreciated. Thanks a lot, jrn

  Read the article

• How do I fix my resolution after Directx install through Steam?

  - by Justin

  I'm a bit long-winded so see bottom for quick version and specs. Friendly Hello: Hello all on these askUbuntu pages, I just recently built my own computer and decided to switch to Ubuntu for the extra coolness. I've been learning a lot through all this, and mostly been trying to figure out issues on my own (read: Google searches). However, I couldn't seem to find others with this problem so I've come here for help. Detailed Recount: So I just used WINE and WINETRICKS to install Steam. All went well and it worked. Then I went to trying a game out. I remembered that Orcs Must Die! worked from http://www.steamgamesonlinux.com/ so I tried that out. After selecting to download it, that's when the problem occurred. The screen suddenly zoomed in!!! I think it's the resolution right? Half the screen is cut off and I can't see parts of the right side of windows. My theory is that this is due to Direct X being installed through Steam, as Steam automatically installed it as I chose to download the game. It didn't even ask me to install Direct X or not ): It all happened so fast. This all being said, the game works fine! It looks a little strange, as if the resolution was off, but it plays just fine. What I did so far: Restarted my computer. Didn't work -_- Researched Steam installing DirectX on Ubuntu then messing up resolution and couldn't really find anything. Researched uninstalling DirectX from Ubuntu but only found uninstalling DirectX after having been installed with Wine, not through Steam. Got mad and ate my feelings. Tried "xrandr -s 0" but it didn't do anything. Ran xrandr alone and terminal showed this: Screen 0: minimum 8 x 8, current 640 x 480, maximum 16384 x 16384 DVI-I-0 connected 640x480+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 640x480 59.9*+ 320x240 120.1 DVI-I-1 disconnected (normal left inverted right x axis y axis) HDMI-0 disconnected (normal left inverted right x axis y axis) DP-0 disconnected (normal left inverted right x axis y axis) DVI-D-0 disconnected (normal left inverted right x axis y axis) DP-1 disconnected (normal left inverted right x axis y axis) About now I was mad so I played Odin's Sphere then took a nap. Back to it! I entered the following: xrandr --output DVI-I-0 --mode 1024x768 But I was met with this message: xrandr: cannot find mode 1024x768 I get the same messages for 800x600, 1400x1050, and seemingly any other combination of numbers. I then tried Going into System Settings then Displays, then playing around in there. My Resolution is set to 640x480 and there are no other options for me to choose from. Rotation has Normal, Clockwise, Counter Clockwise, and 180 Degrees. It's set to Normal and I haven't messed with that. Launcher Placement has Unknown and All Displays as its two options. It's set to Unknown, but moving it to All Displays doesn't seem to do anything. Finally, when I click Detect Displays, nothing seems to happen. Quick Version: Linux noob. Steam installed with Wine and Winetricks. Steam downloaded and installed game + DirectX. Resolution messed up now (I think; pretty sure), can't fix it, very annoying, no idea what's going on, halp! Specs: Ubuntu Version 12.04 Wine Version 1.4.1 Have not changed any settings in Wine Using Winetricks Graphics Card: http://www.gigabyte.com/products/pro...px?pid=4361#sp Drivers: Proprietary (Installing those were a LOT of fun) Also let it be known that I have a DVI to VGA cord running from my Graphics card to my monitor. If any more information is needed I am ready to report. Thank You: Thanks a lot for your help and all the work you do to support noob ubuntuers like me (:

  Read the article

• iOS 5 New Features vs Android

  - by kerry

  Browsing through the iOS 5 features list, I can’t help but notice a lot of it is catch up. Having owned both an iPhone and an Android for a considerable amount of time, I figured I would jot down my opinions. Notification Center – Completely ripped off from Android but looks good and is a much needed addition iMessage – This is very interesting as most people who would think it’s cool, probably really wouldn’t understand the significance.  Basically, Apple is adding an IM application to iOS.  Now iPhone / iPad users can sit around messaging each other how cool it is like Crackberry users circa 2003.  I guess the only real improvement over MMS is that you can easily setup groups, see when each other are typing, and don’t incur text messaging charges; at the expense of leaving your non-iOS buddies out (who wants to talk to those losers anyways?). Newstand – An app update and not an OS one (Apple typically doesn’t make distinctions).  It all seems like stuff my current Nook stuff will do.  Note: I did look to compare prices but it seems that information is not available without downloading iTunes.  lame. Reminders – TODO lists are ho hum, but the ability to have reminders when you arrive or leave a position is pretty cool. Twitter integration – The fact that the best Apple can come up with is ‘one at a timing’ online service integration is laughable at best. Camera – Can control it from the lock screen.  Now you’ll have tons of pocket lint photos in your iCloud to go along with the wicked shot of that cheetah that just unexpectedly ran by your apartment. Photos – Speaking of iCloud, all of your devices photos will be synced through it.  That’s cool I guess, not sure if Android will do the same. Safari – What?  You haven’t been reading rss feeds on your device this whole time?  Something tells me you aren’t about to start. PC Free – Finely Apple untethers the iPhone.  What took them so long? Game Center – This should be an interesting service.  Attention Apple fanboys immediately forget how they are blatantly copying Microsoft achievements (at least rename them). Wifi Sync – Just couldn’t cut the cord completely could they?  For what it’s worth, the Zune has been doing this for 5 years now. All in all a pretty big update.  Mostly iCloud.  Mostly keeping up the mobile status quo.  As an Android user, I can’t say there is anything I am envious of.

  Read the article

• Mounting NAS share: Bad Address

  - by Korben

  I've faced to the problem that can't solve. Hope you can help me with it. I have a storage QNAP TS-459U, with it's own Linux, and 'massive1' folder shared, which I need to mount to my Debian server. They are connected by regular patch cord. Debian server has two network interfaces - eth0 and eth1. eth0 is for Internet, eth1 is for QNAP. So, I'm saying this: mount -t cifs //169.254.100.100/massive1/ /mnt/storage -o user=admin , where 169.254.100.100 is an IP of QNAP's interface. The result I get (after entering password): mount error(14): Bad address Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) Tried: mount.cifs, smbmount, with '/' at the end of the network share and without it, and many other variations of that command. And always its: mount error(14): Bad address Funny thing is when I was in Data Center, I had connected my netbook to QNAP by the same scheme (with Fedora 16 on it), and it connected without any problems, I could read/write files on the QNAP's NAS share! So I'm really stuck with the Debian. I can't undrestand where's the difference with Fedora, making this error. Yeah, I've used Google. Couldn't find any useful info. Ping to the QNAP's IP is working, I can log into QNAP's Linux by ssh, telnet on 139's port is working. This is network interface configuration I use in Debian: IP: 169.254.100.1 Netmask: 255.255.0.0 The only diffence in connecting to Fedora and Debian is that in Fedora I've added gateway - 169.254.100.129, but ping to this IP is not working, so I think it's not necessary at all. P.S. ~# cat /etc/debian_version wheezy/sid ~# uname -a Linux host 2.6.32-5-openvz-amd64 #1 SMP Mon Mar 7 22:25:57 UTC 2011 x86_64 GNU/Linux ~# smbtree WORKGROUP \\HOST host server \\HOST\IPC$ IPC Service (host server) \\HOST\print$ Printer Drivers NAS \\MASSIVE1 NAS Server \\MASSIVE1\IPC$ IPC Service (NAS Server) \\MASSIVE1\massive1 \\MASSIVE1\Network Recycle Bin 1 [RAID5 Disk Volume: Drive 1 2 3 4] \\MASSIVE1\Public System default share \\MASSIVE1\Usb System default share \\MASSIVE1\Web System default share \\MASSIVE1\Recordings System default share \\MASSIVE1\Download System default share \\MASSIVE1\Multimedia System default share Please, help me with solving this strange issue. Thanks before.

  Read the article

• Power cycles on/off 3 times before booting properly from cold start, no other issues (New System)

  - by James

  Relevant Specs: Sapphire 5850, core i7 920, Seasonic x750 power supply, ECS X58B-A2 mobo. From a cold boot, meaning all power totally disconnected at the wall, the system will power on for less than a second and then power off completely. After two seconds of being powered off this will repeat and on the third "attempt" the computer will boot. To be very specific here is what happens: The power is turned on at the wall and on the psu, the orange stdby LED on the mobo is illuminated but the system is 'off'. I hit the power button on the case or on the mobo itself I hear the relay (?) in the psu closing The case light comes on and the mobo power light comes on. The fans start rotating. Immediately after this the I hear some relay click - the power lights extinguish, the fans stop, the stdby light remains on. Less than 2 seconds pass and the cycle repeats without any intervention from me. On the third attempt it boots normally and the machine runs perfectly. If I do a soft reboot or a full shutdown the computer starts normally the next time. It's only if I pull the power cord or flick the switch off on the PSU that I get the cycling again. Basically any time the stdby light on the mobo goes out. I have removed the graphics card and I get the same problem. I have removed the PSU, hotwired it to the ON position and verified voltages on all lines. The relay does not cycle when I do this. If I connect only the 24 pin ATX connector to the mobo and not the 8 pin ATX12V / CPU connector then I will not get the cycling, the fans run, the power light stays on, but obviously the system can't boot. Disconnecting all fans has no effect on the problem. My feeling it that it's something to do with the motherboard like a capacitor that's taking a long time to charge because it's leaking or something along those lines. But I can't imagine what could be 'wrong' with it and only manifest itself as a problem under these very specific circumstances. Any ideas? Thanks.

  Read the article

• Get 5.1 surround sound from computer through a VCR config?

  - by Wedding Nails

  I'm posting to see if my idea of this setup is right and can be done. I currently have the following "equipment": a JVC VCR -quite old-, which has built in surround sound (aka it has several speaker outputs, which I believe is 5.1 and are connected to several speakers that are in every corner of the room), a computer with SPDIF optical output and a new flat screen TV (with built in HDMI). I want the computer to take advantage of the VCR's surround system (all the speakers in the room) in order to play mainly music and video always with all the speakers (5.1) and with the maximum sound quality. Currently, the computer plays sound only through the front speaker (I connect one output to the on board pc audio input) and the quality is really bad. As a side note, the computer video runs with S-video (old school), and the picture quality as you would imagine, is really bad with the new big LCD screen. My main goals are: to upgrade the picture with a new video card which would support HDMI (my tv has HDMI). to buy a SPDIF optical cable, connect one end to the VCR SPDIF input and the other end to the PC output This is theoretically what I've researched so far, and I came out with several questions: in this case, with the SPDIF cable connected, and all the configurations done in windows allowing the 5.1, will I get every content I play "converted" or played through all of my speakers? (I read this forum post). I already know that in order for this setup to play from all the speakers, the content/audio source has to be 5.1. but my question is, if there is a way to play from all of the speakers no matter what type of content I'm playing (that's why I said conversion there) I already know that HDMI cables carry digital sound. Is there a way I can only use said HDMI cord to the tv, and get sound through the VCR? (I'm not too sure about this, I would have to disable the TVs speakers and use the VCR surround as default, but I have no clue wether this can be done or not). Update: The ultimate question is, do I really have to rely on "sound virtualization" technology to get sound from all the speakers, no matter what content I play? (do I require a newer sound card, like a creative soundblaster with said technology?) Thanks!

  Read the article

• Melting Laptop Power Supply Tip

  - by AlReece45

  Several (6-7) months ago, my laptop power supply cord got a cut in it and stopped working. Having gotten cheap (and short) power supplies in the past, I decided to buy 2 brand new ones from the manufacturer (ASUS). Now, I used my laptop a little less than usual between February and March. During that time I noticed a few times that the power supply, even though plugged in, did not provide power. Often the computer would just off on me. I figured it was just that one power supply being bad. I had left the alternate at my parent's house in another state and asked them to ship it to me. Now, at work the other day I wanted to get a file off the of hard disk. So I booted it up, knowing that it had a low battery, plugged it in. During the first 2 minutes of use, I was told that the battery was low and I should plug it in. I unplugged it, inspected the end (Being plugged in, this was suspicious), and decided I shouldn't plug it back in-- the plastic on the tip was melting from the heat of the metal on the tip. The computer had simply booted up and I had the file-manager open. It had not been on for more than 10 hours. Now I know that computers tend to get pretty hot. However, the melting point of plastic is usually above 200C.. so that's much hotter than the computer should be generating. I went and bought a THIRD power supply. This time a universal one from Best Buy (it was very fast to buy and test). I tried it out on the computer and it's tip is melting as well. My older laptop that uses the universal power supply uses it perfectly (has been about a week and a part of use now). I have tried using the computer without the battery, with the same effect. Obviously, this is not a problem with the power supply. My room mate and I being trained computer techs were contemplating taking the computer apart and desoldering and resoldering on the power tip. (The computer is about 6 months out of its 2-year warranty). We're hoping that will correct the issue as I would prefer to devote my money on a Good Desktop rather than yet ANOTHER $1200+ laptop. Is there any thing I'm missing here that might cause the the tip on the power unit to melt?

  Read the article

• Off The Beaten Path—Three Things Growing Midsize Companies are Thankful For

  - by Christine Randle

  By: Jim Lein, Senior Director, Oracle Accelerate Last Sunday I went on a walkabout.  That’s when I just step out the door of my Colorado home and hike through the mountains for hours with no predetermined destination. I favor “social trails”, the unmapped routes pioneered by both animal and human explorers.  These tracks  are usually more challenging than established, marked routes and you can’t be 100% sure of where you’re going to end up. But I’ve found the rewards to be much greater. For awhile, I pondered on how—depending upon your perspective—the current economic situation worldwide could be viewed as either a classic “the glass is half empty” or a “the glass is half full” scenario. Midsize companies buy Oracle to grow and so I’m continually amazed and fascinated by the success stories our customers relate to me.  Oracle’s successful midsize companies are growing via innovation, agility, and opportunity. For them, the glass isn’t half full—it’s overflowing. Growing Midsize Companies are Thankful for: Innovation The sun angling through the pine trees reminded me of a conversation with a European customer a year ago May.  You might not recognize the name but, chances are, your local evening weather report relies on this company’s weather observation, monitoring and measurement products.  For decades, the company was recognized in its industry for product innovation, but its recent rapid growth comes from tailoring end to end product and service solutions based on the needs of distinctly different customer groups across industrial, public sector, and defense sectors.  Hours after that phone call I was walking my dog in a local park and came upon a small white plastic box sprouting short antennas and dangling by a nylon cord from a tree branch.  I cut it down. The name of that customer’s company was stamped on the housing. “It’s a radiosonde from a high altitude weather balloon,” he told me the next day. “Keep it as a souvenir.”  It sits on my fireplace mantle and elicits many questions from guests. Growing Midsize Companies are Thankful for: Agility In July, I had another interesting discussion with the CFO of an Asia-Pacific company which owns and operates a large portfolio of leisure assets. They are best known for their epic outdoor theme parks. However, their primary growth today is coming from a chain of indoor amusement centers in the USA where billiards, bowling, and laser tag take the place of roller coasters, kiddy rides, and wave pools. With mountains and rivers right out my front door, I’m not much for theme parks, but I’ll take a spirited game of laser tag any day.  This company has grown dramatically since first implementing Oracle ERP more than a decade ago. Their profitable expansion into a completely foreign market is derived from the ability to replicate proven and efficient best business practices across diverse operating environments.  They recently went live on Oracle’s Fusion HCM and Taleo. Their CFO explained to me how, with thousands of employees in three countries, Fusion HCM and Taleo would enable them to remain incredibly agile by acting on trends linking individual employee performance to their management, establishing and maintaining those best practices. Growing Midsize Companies are Thankful for: Opportunity I have three GPS apps on my iPhone. I use them mainly to keep track of my stats—distance, time, and vertical gain. However, every once in awhile I need to find the most efficient route back home before dark from my current location (notice I didn’t use the word “lost”). In August I listened in on an interview with the CFO of another European company that designs and delivers telematics solutions—the integrated use of telecommunications and informatics—for managing the mobile workforce. These solutions enable customers to achieve evolutionary step-changes in their performance and service delivery. Forgive the overused metaphor, but this is route optimization on steroids.  The company’s executive team saw an opportunity in this emerging market and went “all in”. Consequently, they are being rewarded with tremendous growth results and market domination by providing the ability for their clients to collect and analyze performance information related to fuel consumption, service workforce safety, and asset productivity. This Thanksgiving, I’m thankful for health, family, friends, and a career with an innovative company that helps companies leverage top tier software to drive and manage growth. And I’m thankful to have learned the lesson that good things happen when you get off the beaten path—both when hiking and when forging new routes through a complex world economy. Halfway through my walkabout on Sunday, after scrambling up a long stretch of scree-covered hill, I crested a ridge with an obstructed view of 14,265 ft Mt Evans just a few miles to the west.  There, nowhere near a house or a trail, someone had placed a wooden lounge chair. Its wood was worn and faded but it was sturdy. I had lunch and a cold drink in my pack. Opportunity knocked and I seized it. Happy Thanksgiving.  

  Read the article

• Need help with testdisk output

  - by dan

  I had (note the past tense) an ubuntu 12.04 system with separate partitions for the base and /home directories. It started acting wonky, so I decided to do a reinstall with 12.10, intending just to do a reinstall to the base partition. After several seconds, I realize that the installer was repartitioning the drive and reinstalling, so I pulled the power cord. I'm now trying to recover as much as I can with testdisk, but it seems that testdisk is finding 100 unique partitions when I run it - they mostly tend to be HFS+ or solaris /home (which I think is just an ext4; I've never had solaris on the machine). I've pasted an abbreviated version of the testdisk output below (first ~100 lines, and then ~100 lines from the middle of the output). Is there a way to combine or recreate the partitions and then data recovery, or some other way maximize what I can recover (ideally as much of the file system as possible)? I really only care about what was in the /home directory - I'd rather not use photorec since I don't have another 2 TB HD lying around to recover to. Thanks, Dan Mon Dec 10 06:03:00 2012 Command line: TestDisk TestDisk 6.13, Data Recovery Utility, November 2011 Christophe GRENIER <[email protected]> http://www.cgsecurity.org OS: Linux, kernel 3.2.34-std312-amd64 (#2 SMP Sat Nov 17 08:06:32 UTC 2012) x86_64 Compiler: GCC 4.4 Compilation date: 2012-11-27T22:44:52 ext2fs lib: 1.42.6, ntfs lib: libntfs-3g, reiserfs lib: 0.3.1-rc8, ewf lib: none /dev/sda: LBA, HPA, LBA48, DCO support /dev/sda: size 3907029168 sectors /dev/sda: user_max 3907029168 sectors /dev/sda: native_max 3907029168 sectors Warning: can't get size for Disk /dev/mapper/control - 0 B - CHS 1 1 1, sector size=512 /dev/sr0 is not an ATA disk Hard disk list Disk /dev/sda - 2000 GB / 1863 GiB - CHS 243201 255 63, sector size=512 - WDC WD20EARS-00J2GB0, S/N:WD-WCAYY0075071, FW:80.00A80 Disk /dev/sdb - 1013 MB / 967 MiB - CHS 1014 32 61, sector size=512 - Generic Flash Disk, FW:8.07 Disk /dev/sr0 - 367 MB / 350 MiB - CHS 179470 1 1 (RO), sector size=2048 - PLDS DVD+/-RW DH-16AAS, FW:JD12 Partition table type (auto): Intel Disk /dev/sda - 2000 GB / 1863 GiB - WDC WD20EARS-00J2GB0 Partition table type: EFI GPT Analyse Disk /dev/sda - 2000 GB / 1863 GiB - CHS 243201 255 63 Current partition structure: Bad GPT partition, invalid signature. search_part() Disk /dev/sda - 2000 GB / 1863 GiB - CHS 243201 255 63 recover_EXT2: s_block_group_nr=0/14880, s_mnt_count=5/4294967295, s_blocks_per_group=32768, s_inodes_per_group=8192 recover_EXT2: s_blocksize=4096 recover_EXT2: s_blocks_count 487593984 recover_EXT2: part_size 3900751872 MS Data 2048 3900753919 3900751872 EXT4 Large file Sparse superblock, 1997 GB / 1860 GiB Linux Swap 3900755968 3907028975 6273008 SWAP2 version 1, 3211 MB / 3062 MiB Results P MS Data 2048 3900753919 3900751872 EXT4 Large file Sparse superblock, 1997 GB / 1860 GiB P Linux Swap 3900755968 3907028975 6273008 SWAP2 version 1, 3211 MB / 3062 MiB interface_write() 1 P MS Data 2048 3900753919 3900751872 2 P Linux Swap 3900755968 3907028975 6273008 search_part() Disk /dev/sda - 2000 GB / 1863 GiB - CHS 243201 255 63 recover_EXT2: s_block_group_nr=0/14880, s_mnt_count=5/4294967295, s_blocks_per_group=32768, s_inodes_per_group=8192 recover_EXT2: s_blocksize=4096 recover_EXT2: s_blocks_count 487593984 recover_EXT2: part_size 3900751872 MS Data 2048 3900753919 3900751872 EXT4 Large file Sparse superblock, 1997 GB / 1860 GiB block_group_nr 1 recover_EXT2: "e2fsck -b 32768 -B 4096 device" may be needed recover_EXT2: s_block_group_nr=1/14880, s_mnt_count=0/4294967295, s_blocks_per_group=32768, s_inodes_per_group=8192 recover_EXT2: s_blocksize=4096 recover_EXT2: s_blocks_count 487593984 recover_EXT2: part_size 3900751872 MS Data 2046 3900753917 3900751872 EXT4 Large file Sparse superblock Backup superblock, 1997 GB / 1860 GiB block_group_nr 1 recover_EXT2: "e2fsck -b 32768 -B 4096 device" may be needed recover_EXT2: s_block_group_nr=1/14880, s_mnt_count=0/4294967295, s_blocks_per_group=32768, s_inodes_per_group=8192 recover_EXT2: s_blocksize=4096 recover_EXT2: s_blocks_count 487593984 recover_EXT2: part_size 3900751872 MS Data 2048 3900753919 3900751872 EXT4 Large file Sparse superblock Backup superblock, 1997 GB / 1860 GiB block_group_nr 1 recover_EXT2: "e2fsck -b 32768 -B 4096 device" may be needed recover_EXT2: s_block_group_nr=1/14584, s_mnt_count=0/27, s_blocks_per_group=32768, s_inodes_per_group=8192 recover_EXT2: s_blocksize=4096 recover_EXT2: s_blocks_count 477915164 recover_EXT2: part_size 3823321312 MS Data 4094 3823325405 3823321312 EXT4 Large file Sparse superblock Backup superblock, 1957 GB / 1823 GiB block_group_nr 1 ....snip...... MS Data 2046 3900753917 3900751872 EXT4 Large file Sparse superblock Backup superblock, 1997 GB / 1860 GiB MS Data 2048 3900753919 3900751872 EXT4 Large file Sparse superblock, 1997 GB / 1860 GiB MS Data 4094 3823325405 3823321312 EXT4 Large file Sparse superblock Backup superblock, 1957 GB / 1823 GiB MS Data 4096 3823325407 3823321312 EXT4 Large file Sparse superblock Backup superblock, 1957 GB / 1823 GiB MS Data 7028840 7033383 4544 FAT12, 2326 KB / 2272 KiB Mac HFS 67856948 67862179 5232 HFS+ found using backup sector!, 2678 KB / 2616 KiB Mac HFS 67862176 67867407 5232 HFS+, 2678 KB / 2616 KiB Mac HFS 67862244 67867475 5232 HFS+ found using backup sector!, 2678 KB / 2616 KiB Mac HFS 67867404 67872635 5232 HFS+, 2678 KB / 2616 KiB Mac HFS 67867472 67872703 5232 HFS+, 2678 KB / 2616 KiB Mac HFS 67872700 67877931 5232 HFS+, 2678 KB / 2616 KiB Mac HFS 67937834 67948067 10234 [EasyInstall_OSX] HFS found using backup sector!, 5239 KB / 5117 KiB Mac HFS 67938012 67948155 10144 HFS+ found using backup sector!, 5193 KB / 5072 KiB Mac HFS 67948064 67958297 10234 [EasyInstall_OSX] HFS, 5239 KB / 5117 KiB Mac HFS 67948070 67958303 10234 [EasyInstall_OSX] HFS found using backup sector!, 5239 KB / 5117 KiB Mac HFS 67948152 67958295 10144 HFS+, 5193 KB / 5072 KiB Mac HFS 67958292 67968435 10144 HFS+, 5193 KB / 5072 KiB Mac HFS 67958300 67968533 10234 [EasyInstall_OSX] HFS, 5239 KB / 5117 KiB Mac HFS 67992596 67997827 5232 HFS+ found using backup sector!, 2678 KB / 2616 KiB Mac HFS 67997824 68003055 5232 HFS+, 2678 KB / 2616 KiB Mac HFS 67997892 68003123 5232 HFS+ found using backup sector!, 2678 KB / 2616 KiB Mac HFS 68003052 68008283 5232 HFS+, 2678 KB / 2616 KiB Mac HFS 68003120 68008351 5232 HFS+, 2678 KB / 2616 KiB Mac HFS 68008348 68013579 5232 HFS+, 2678 KB / 2616 KiB Solaris /home 84429840 123499141 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84429952 123499253 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84493136 123562437 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84493248 123562549 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84566088 123635389 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84566200 123635501 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84571232 123640533 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84571344 123640645 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84659952 123729253 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84660064 123729365 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84690504 123759805 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84690616 123759917 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84700424 123769725 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84700536 123769837 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84797720 123867021 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84797832 123867133 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84812544 123881845 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84812656 123881957 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84824552 123893853 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84824664 123893965 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84847528 123916829 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84847640 123916941 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84886840 123956141 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84886952 123956253 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84945488 124014789 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84945600 124014901 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84957992 124027293 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84958104 124027405 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84962240 124031541 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84962352 124031653 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84977168 124046469 39069302 UFS1, 20 GB / 18 GiB Solaris /home 84977280 124046581 39069302 UFS1, 20 GB / 18 GiB MS Data 174395467 178483851 4088385 ..... snip (it keeps going on for quite a while)

  Read the article

• Specs, Form and Function – What am I Missing?

  - by Barry Shulam

  0 0 1 628 3586 08041 29 8 4206 14.0 Normal 0 false false false EN-US JA X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:12.0pt; font-family:Cambria; mso-ascii-font-family:Cambria; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Cambria; mso-hansi-theme-font:minor-latin;} Friday October 26th the Microsoft Surface RT arrived at the office.  I was summoned to my boss’s office for the grand unpacking.  If I had planned ahead I could have used my iPhone 4 to film the event and post it on YouTube however the desire to hold the device and turn it ON was more inviting than becoming a proxy reviewer for Engadget’s website.  1980 was the first time we had a personal computer in our house.  It was a  Kaypro computer. It weighed 29 pounds more than any persons lap could hold.  Then the term “portable computer” meant you could remove it from the building and take it else where.  Today I am typing on this entry on a Macbook Air which weighs 2.38 pounds. This morning Amazons front page main title is: “Much More for Much Less” I was born at the right time to start with the CPM operating system on the Kaypro thru the DOS, Windows, Linux, Mac OSX and mobile phone operating systems and languages.  If you are not aware Technology is moving at a rapid pace.  The New iPad (those who are keeping score – iPad4) is replacing a 7 month old machine the New iPad (iPad 3) I have used and owned many technology devices in my life.  The main point that most of the reader who are in the USA overlook is the fact that we are in the USA.  The devices we purchase have a great digital garden to support them.  The Kaypro computer had a 7-inch screen.  It was a TV tube with two colors – Black and Green.  You could see the 80-column screen flicker with characters – have you every played Pac-Man emulated on the screen with the ABC characters. Traveling across the world you will find that not all apps on your device will function as they did back home because they are not offered outside of your country of origin. I think the main question a buyer of technology should be asking is Function.  The greatest Specs with out function limit you.  The most beautiful form with out function is the same as a crystal vase on your shelf – not a good cereal bowl in the morning. Microsoft Surface RT, Amazon Kindle Fire and Apple iPad all great devices in their respective customers hands. My advice for those looking to purchase on this year:  If the device is your only technology device you buy what you WANT and LIKE. Consider this parallel universe if its not your only device?  Ever go shopping for clothing, shoes, and accessories with your wife, girlfriend, sister or mother?  If you listen carefully you will hear the little voices coming out of there heads saying:  “This goes well with that and I can use it also with that outfit” ”Do you think this clashes with that?”  “Ohh I love how that combination looks on you”.  Portable devices such as tablets and computers can offer a whole lot more when they are combined with the digital echo system you have at home and the manufacturer offers online. Pros of each Device: Microsoft Surface RT: There is a new functionality named SmartGlass which will let you share the content off your tablet to your XBOX 360.  Microsoft office is loaded on the tablet.  You can have more than one user profile on the tablet if you share it with others.   Amazon Kindle or Kindle HD: If you are an Amazon consumer with an annual Amazon Prime service you can consume videos and read books off the Amazon site.  Its the cheapest device.  Its a step up from the kindle reader in many ways.   Apple Ipad or Ipad mini: Over 270 Thousand applications.  Airplay permits you the ability to share to your TV screen. If you are a cord cutter (a person who gets their entertainment content over the web or air vs Cable Providers) the Airplay or Smart glass are a huge bonus.  iPad mini or not: The mini will fit in a purse where the larger one will not.  Its lighter which makes it nice to hold for prolonged periods.  It has an option for LTE wireless which non of the other sub 9 inch tables offer.  The screen is non retina which means the applications are smaller.  Speaking with individuals who are above 50 in age that wear glasses they retina does not make a difference for them however they prefer the larger iPad over the new mini.   Happy Shopping this Channuka Season.   The Kosher Coder.   Follow me on twitter @KosherCoder

  Read the article

• How do I connect my Windows XP laptop to the internet?

  - by rubysiddhi

  Hello fellow super users, The Past I have a Acer Travelmate 2300 laptop running Windows XP. 6 months ago I moved into a new apartment and got a new internet connection set up. After getting an internet connection installed in my apartment I reinstalled Windows XP and at the same time wiped my drive clean losing all the original Acer software and drivers. Once XP was reinstalled I had to find all the drivers again to get the Travelmate laptop connected to the internet. So, using my Vista laptop which was connected fine, I went to the Acer Travelmate Series drivers download page to download the necessary drivers. I transferred them to my Acer XP machine and installed them the best I could (there were no easy instructions so I just had to find all the executables and run them). I eventually got connected to the internet but not exactly in the way I had hoped for. The Present To be connected to the internet I need to have an Ethernet cord connecting my computer (via the Ethernet port) to my router. This is a problem since it defeats the purpose of having a Wireless LAN card in my Acer laptop. One of the programs I downloaded from the Acer Travelmate Series page was the Acer Wireless LAN Configuration Utility. This program allows me to see the current network I am connected to and all the available networks I could potentially connect to. It reminds me of XP's Wireless Network Connection window/utility where you can see all available wireless networks, refresh the network list and connect to one of the networks. I should mention that my ISP set up a security enabled wireless network with WPA. This network requires a network key if you want to connect to it. I guess my Vista computer has the network key entered into it already. The problem is that I do not know what the network key is. Now obviously you would say just contact my ISP to get the key. And I will but there is just one extra weird issue. I am able to connect to another unsecured wireless network in the Wireless Network Connection window/utility. I can be on it as long as my Ethernet cable is plugged in. So this is not really wireless is it? And this indicates that even if I do get that network key password from my ISP, I will only solve one of the two problems I have. I will only solve being able to get online as long as I am connected to my router via the Ethernet cable. The Main Questions So how do I enable my acer IPN2220 Wireless LAN Card so that I can use my Acer laptop from anywhere with in my apartment? Or should I first get the network key from my ISP to access my security enabled wireless network? And then deal with getting the acer IPN2220 Wireless LAN Card working? Hard & Learned VS Easy & Stupid Of course contacting the ISP would be easier. Have em just come in here and do there thing. The problem with that is that they do not speak English (yeah, im in Poland) and it'd be a hell of a time trying to understand what they are doing (uncomfortable looking over their shoulder). Also, I want to learn how to do this task myself so that I can fix the problem if it ever happens again. You know, be more self sufficient. I look forward to helpful replies. Thanks, Xaviour

  Read the article

• print individual tables ??

  - by LiveEn

  I am getting values from a database and displaying in a table. Im trying to print the results as individual . Im using the below javascript <script type="text/javascript"> function print_parent(element) { element.parentNode.className = 'print'; window.print(); element.parentNode.className = ''; return false; } </script> The problem that i have is when i try to print all the results it works great.can some one please tell me how can i print each individual table in each result please? below is my php code $sql="select * from cisdb where pids LIKE '%$pids%'"; $result=mysql_query($sql) or die(mysql_error()); if (mysql_num_rows($result)==0) { echo '<b><center>There was no records !</center></b>'."<br>"; } while ($row=mysql_fetch_array($result)) { $cat=str_replace('+', ' ', $row['category']); print "<center>"; print "<table width='472' border='1' align='center' class='noprint'>"; print "<tr>"; print "<td width='150'><div align='center'><a href='#' onclick='return print_parent(this)'>Print</a> </div></td>"; print "<td width='150'><div align='center'><a href='process.php?mode=ed&id={$row['id']}'>Edit</div></td>"; print "<td width='150'><div align='center'><a href='process.php?mode=del&id={$row['id']}' onclick='return confirm('Are you sure you want to delete?')'>Delete</a></div></td>"; print "</tr>"; print "</table><br>"; print "<div id='divToPrint'>"; print"<table width=700 style=height:900 border=1 cellpadding=1 cellspacing=1 bordercolor=#D6D6D6 class=sss title={$row['title']}> <tr> <td height=25 colspan=2 align=left valign=top><strong>Customer:{$row['name']}</strong></td> <td width=183 align=left valign=top><strong>Sales ID:{$row['said']} </strong></td> <td width=100 align=left valign=top><strong>Phone Cord. ID:{$row['pcid']}</strong></td> <td align=left valign=top><strong>Type:{$row['classtype']}</strong></td> </tr> <tr> <td height=25 colspan=2 valign=top><strong>Contact Name: </strong></td> <td colspan=2 valign=top><strong>Email:</strong></td> <td width=154 valign=top><strong>Phone:</strong></td> </tr <tr> <td height=15 colspan=5 valign=top><strong>Remarks:</strong></td> </tr> <tr> <td height=15 colspan=2 valign=top><strong>Date Added: </strong></td> <td valign=top><strong>Date Edited : </strong></td> <td colspan=2 valign=top><strong>Printed : </strong></td> </tr> </table></div><br>"; print "</center>"; }

  Read the article

• UAT Testing for SOA 10G Clusters

  - by [email protected]

  A lot of customers ask how to verify their SOA clusters and make them production ready. Here is a list that I recommend using for 10G SOA Clusters. v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 false false false EN-CA X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0cm; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; mso-bidi-font-size:12.0pt; font-family:"Calibri","sans-serif"; mso-fareast-language:EN-US;} Test cases for each component - Oracle Application Server 10G General Application Server test cases This section is going to cover very General test cases to make sure that the Application Server cluster has been set up correctly and if you can start and stop all the components in the server via opmnct and AS Console. Test Case 1 Check if you can see AS instances in the console Implementation 1. Log on to the AS Console --> check to see if you can see all the nodes in your AS cluster. You should be able to see all the Oracle AS instances that are part of the cluster. This means that the OPMN clustering worked and the AS instances successfully joined the AS cluster. Result You should be able to see if all the instances in the AS cluster are listed in the EM console. If the instances are not listed here are the files to check to see if OPMN joined the cluster properly: $ORACLE_HOME\opmn\logs{*}opmn.log*$ORACLE_HOME\opmn\logs{*}opmn.dbg* If OPMN did not join the cluster properly, please check the opmn.xml file to make sure the discovery multicast address and port are correct (see this link  for opmn documentation). Restart the whole instance using opmnctl stopall followed by opmnctl startall. Log on to AS console to see if instance is listed as part of the cluster. Test Case 2 Check to see if you can start/stop each component Implementation Check each OC4J component on each AS instanceStart each and every component through the AS console to see if they will start and stop.Do that for each and every instance. Result Each component should start and stop through the AS console. You can also verify if the component started by checking opmnctl status by logging onto each box associated with the cluster Test Case 3 Add/modify a datasource entry through AS console on a remote AS instance (not on the instance where EM is physically running) Implementation Pick an OC4J instanceCreate a new data-source through the AS consoleModify an existing data-source or connection pool (optional) Result Open $ORACLE_HOME\j2ee\<oc4j_name>\config\data-sources.xml to see if the new (and or the modified) connection details and data-source exist. If they do then the AS console has successfully updated a remote file and MBeans are communicating correctly. Test Case 4 Start and stop AS instances using opmnctl @cluster command Implementation 1. Go to $ORACLE_HOME\opmn\bin and use the opmnctl @cluster to start and stop the AS instances Result Use opmnctl @cluster status to check for start and stop statuses.  HTTP server test cases This section will deal with use cases to test HTTP server failover scenarios. In these examples the HTTP server will be talking to the BPEL console (or any other web application that the client wants), so the URL will be _http://hostname:port\BPELConsole Test Case 1  Shut down one of the HTTP servers while accessing the BPEL console and see the requested routed to the second HTTP server in the cluster Implementation Access the BPELConsoleCheck $ORACLE_HOME\Apache\Apache\logs\access_log --> check for the timestamp and the URL that was accessed by the user. Timestamp and URL would look like this 1xx.2x.2xx.xxx [24/Mar/2009:16:04:38 -0500] "GET /BPELConsole=System HTTP/1.1" 200 15 After you have figured out which HTTP server this is running on, shut down this HTTP server by using opmnctl stopproc --> this is a graceful shutdown.Access the BPELConsole again (please note that you should have a LoadBalancer in front of the HTTP server and configured the Apache Virtual Host, see EDG for steps)Check $ORACLE_HOME\Apache\Apache\logs\access_log --> check for the timestamp and the URL that was accessed by the user. Timestamp and URL would look like above Result Even though you are shutting down the HTTP server the request is routed to the surviving HTTP server, which is then able to route the request to the BPEL Console and you are able to access the console. By checking the access log file you can confirm that the request is being picked up by the surviving node. Test Case 2 Repeat the same test as above but instead of calling opmnctl stopproc, pull the network cord of one of the HTTP servers, so that the LBR routes the request to the surviving HTTP node --> this is simulating a network failure. Test Case 3 In test case 1 we have simulated a graceful shutdown, in this case we will simulate an Apache crash Implementation Use opmnctl status -l to get the PID of the HTTP server that you would like forcefully bring downOn Linux use kill -9 <PID> to kill the HTTP serverAccess the BPEL console Result As you shut down the HTTP server, OPMN will restart the HTTP server. The restart may be so quick that the LBR may still route the request to the same server. One way to check if the HTTP server restared is to check the new PID and the timestamp in the access log for the BPEL console. BPEL test cases This section is going to cover scenarios dealing with BPEL clustering using jGroups, BPEL deployment and testing related to BPEL failover. Test Case 1 Verify that jGroups has initialized correctly. There is no real testing in this use case just a visual verification by looking at log files that jGroups has initialized correctly. Check the opmn log for the BPEL container for all nodes at $ORACLE_HOME/opmn/logs/<group name><container name><group name>~1.log. This logfile will contain jGroups related information during startup and steady-state operation. Soon after startup you should find log entries for UDP or TCP.Example jGroups Log Entries for UDPApr 3, 2008 6:30:37 PM org.collaxa.thirdparty.jgroups.protocols.UDP createSockets ·         INFO: sockets will use interface 144.25.142.172·          ·         Apr 3, 2008 6:30:37 PM org.collaxa.thirdparty.jgroups.protocols.UDP createSockets·          ·         INFO: socket information:·          ·         local_addr=144.25.142.172:1127, mcast_addr=228.8.15.75:45788, bind_addr=/144.25.142.172, ttl=32·         sock: bound to 144.25.142.172:1127, receive buffer size=64000, send buffer size=32000·         mcast_recv_sock: bound to 144.25.142.172:45788, send buffer size=32000, receive buffer size=64000·         mcast_send_sock: bound to 144.25.142.172:1128, send buffer size=32000, receive buffer size=64000·         Apr 3, 2008 6:30:37 PM org.collaxa.thirdparty.jgroups.protocols.TP$DiagnosticsHandler bindToInterfaces·          ·         -------------------------------------------------------·          ·         GMS: address is 144.25.142.172:1127·          ------------------------------------------------------- Example jGroups Log Entries for TCPApr 3, 2008 6:23:39 PM org.collaxa.thirdparty.jgroups.blocks.ConnectionTable start ·         INFO: server socket created on 144.25.142.172:7900·          ·         Apr 3, 2008 6:23:39 PM org.collaxa.thirdparty.jgroups.protocols.TP$DiagnosticsHandler bindToInterfaces·          ·         -------------------------------------------------------·         GMS: address is 144.25.142.172:7900------------------------------------------------------- In the log below the "socket created on" indicates that the TCP socket is established on the own node at that IP address and port the "created socket to" shows that the second node has connected to the first node, matching the logfile above with the IP address and port.Apr 3, 2008 6:25:40 PM org.collaxa.thirdparty.jgroups.blocks.ConnectionTable start ·         INFO: server socket created on 144.25.142.173:7901·          ·         Apr 3, 2008 6:25:40 PM org.collaxa.thirdparty.jgroups.protocols.TP$DiagnosticsHandler bindToInterfaces·          ·         ------------------------------------------------------·         GMS: address is 144.25.142.173:7901·         -------------------------------------------------------·         Apr 3, 2008 6:25:41 PM org.collaxa.thirdparty.jgroups.blocks.ConnectionTable getConnectionINFO: created socket to 144.25.142.172:7900  Result By reviewing the log files, you can confirm if BPEL clustering at the jGroups level is working and that the jGroup channel is communicating. Test Case 2  Test connectivity between BPEL Nodes Implementation Test connections between different cluster nodes using ping, telnet, and traceroute. The presence of firewalls and number of hops between cluster nodes can affect performance as they have a tendency to take down connections after some time or simply block them.Also reference Metalink Note 413783.1: "How to Test Whether Multicast is Enabled on the Network." Result Using the above tools you can confirm if Multicast is working  and whether BPEL nodes are commnunicating. Test Case3 Test deployment of BPEL suitcase to one BPEL node.  Implementation Deploy a HelloWorrld BPEL suitcase (or any other client specific BPEL suitcase) to only one BPEL instance using ant, or JDeveloper or via the BPEL consoleLog on to the second BPEL console to check if the BPEL suitcase has been deployed Result If jGroups has been configured and communicating correctly, BPEL clustering will allow you to deploy a suitcase to a single node, and jGroups will notify the second instance of the deployment. The second BPEL instance will go to the DB and pick up the new deployment after receiving notification. The result is that the new deployment will be "deployed" to each node, by only deploying to a single BPEL instance in the BPEL cluster. Test Case 4  Test to see if the BPEL server failsover and if all asynch processes are picked up by the secondary BPEL instance Implementation Deploy a 2 Asynch process: A ParentAsynch Process which calls a ChildAsynchProcess with a variable telling it how many times to loop or how many seconds to sleepA ChildAsynchProcess that loops or sleeps or has an onAlarmMake sure that the processes are deployed to both serversShut down one BPEL serverOn the active BPEL server call ParentAsynch a few times (use the load generation page)When you have enough ParentAsynch instances shut down this BPEL instance and start the other one. Please wait till this BPEL instance shuts down fully before starting up the second one.Log on to the BPEL console and see that the instance were picked up by the second BPEL node and completed Result The BPEL instance will failover to the secondary node and complete the flow ESB test cases This section covers the use cases involved with testing an ESB cluster. For this section please Normal 0 false false false EN-CA X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0cm; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; mso-bidi-font-size:12.0pt; font-family:"Calibri","sans-serif"; mso-fareast-language:EN-US;} follow Metalink Note 470267.1 which covers the basic tests to verify your ESB cluster.

  Read the article

• SOLVED Install MythTV & 11.10 on Lenovo S12 (Intel atom) with wireless

  - by keepitsimpleengineer

  This is how I installed Ubuntu 11.10 and MythTV client on my Lenovo S12 (Intel Atom) laptop and use it using WiFi (see additional notes at end). I did this because the upgrade from 11.04 bricked the laptop. Note that the partitions on the Lenovo standard disk were already in place for this installation. Also note that my LAN is setup for fixed IP addresses. Downloaded and burned 11.10 x86 Desktop Ubuntu CD Connected the power supply cord, LAN wire and the external DVD USB drive. Ran Windows XP and made sure performance level "Performance" was set and "Wireless" was enabled. Booted S12 from CD Disabled Networking from icon on upper left panel icon Edited Connections… "Wired connection 1" ? Set IP address, accepted default netmask and set gateway. Also set DNS server. Good idea to check "Connection Information" here to verify everything's O.K. Selected Install Ubuntu from the initial "Install" window Verified the three items were checked (required disk space available, plugged into a power source, & connected to the Internet) Selected Download updates while installing and third party software. Hit Continue… At wireless selected don't want to connect…WiFi…now. Continue… At Installation type, selected Something else. Continue… At partition tale, selected the ext4 Linux partition, set the mount point as "/", and marked for formatting. Here I selected the main disk (/sda) for installing the boot manager. Continue… Selected or verified my Time zone. Continue… Selected my keyboard layout. Continue… Filled in the who are you fields. Make sure password is required to sign in is checked. Continue… Chose a picture. Continue… I selected import no accounts. Continue… Wait as the Install creeps along. If your screen goes blank, tap the space bar ? apparently the screen saver/power plan does this. There are several progress bars. The longest was "Installing system", and it was the next to the last one. Installation Complete window appears, Restart Now… Wait as it stops, The screen blanks then the message "…remove…media…close tray…press enter" I just unplugged the USB DVD and hit enter… It was disheartening but the screen turned Ubuntu Purple-beige and nothing happened, so I help down the power key until it shut down, the pressed it again and the Grub Boot screen appeared. Select Ubuntu… 25.The screen went blank with the little flashing underscore cursor on it and the disk light would occasionally flash. I hit the enter key and eventuality Ubuntu started. After a somewhat long time the unity desktop appeared. 11.10, unlike earlier versions, retains the connection information. Check this by checking the network icon on the upper left applet panel. Here the touch-pad·mouse quit working and I had to reboot. It takes and extremely long time to boot, sometimes requiring several power off/ power on (cold boot). You can try to get the default network manager to work, but it might not, it didn't on mine for WiFi. Thanks to: Chris at URL here's what to do… disconnect your wired Internet connection. input your wireless information into network manager open a terminal (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "terminal". Might be a good idea to drag and drop the terminal icon to the terminal, it's easy to get rid of later. click to open a terminal, and type in: sudo rmmod acer_wmi && echo "blacklist acer_wmi" >> /etc/modprobe.d/blacklist.conf and hit enter. type in your password as asked. if you have correctly entered your WiFi information and you are near your AP, you should connect immediately if not, see the URL above ? you might need to replace "network manager" with "wicd" ? I did with 11.04. Update the new 11.10, in the upper left panel applet weird·gear icon is menu with a line about updating. It's the new way to invoke Update Manager. Your lenovo S12 (intel atom) should now run the new unity Ubuntu. Point your elbow at the ceiling and pat yourself on the back. Installing Mythbuntu Client 24.1 Open mythbuntu.org/repos (I urge you not to directly use Ubuntu Software Center for this) Install Mythbuntu Repos Save the file (in ~/Downloads, the default) Run the file ? it will update your repositories so that you will get the proper installation sources ? it will start Ubuntu Software Center to do this ? Click Install… You will need your password. Debconf window will open, select by making sure check mark is in the little box "Would you like to activate…". Forward… Which version? At the time of writing the current "Stable" version was 24.1, select 0.24.x… Forward… Read the message, then forward… Delete the downloaded file. Install synaptic (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "synaptic". Click on the synaptic icon. Ubuntu Software Center will open and allow you to install synaptic package manager. Open Synaptic (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "Synaptic". Might be a good idea to drag and drop the terminal icon to the terminal, it's easy to get rid of later. Run synaptic, read the intro, and close the intro window. Type in mythbuntu-control-centre in the Quick filter text box, and then select it "Mark for installation" by clicking on the box next to it's name. Marvel at the additional to be installed items, then select "?Mark"… At the top of the synaptic window click on the "? Apply" button. Marvel at the amount of stuff to be installed, the click on "Apply". When finished, close finished window and synaptic. Open mythbuntu-control-centre (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythbuntu". Might be a good idea to drag and drop the mythbuntu-control-centre icon to the terminal, it's easy to get rid of later. You can now configure and install the frontend. Go down the icon totem on the right side of the window and click as needed… System roles. ? No Backend, Desktop Frontend, and Ubuntu Desktop. Apply… & Apply changes… & Password… MySQL Configuration ? from backend ? Setup General Alt-N(ext) Alt-N(ext) Stetting Access Setup PIN code: ~~~~ Input Security key and click "Test Connection", if ?, then Apply… & Apply… {note: for some inexplicable reason, control centre hung on this, but when I restarted it, it was set properly} Graphics drivers, When I did this, only the Broadcom wireless driver showed up. I closed without doing anything. Services. I enabled SSH & Samba. Apply… & Apply… Repositories. Asked & Answered. MythExport. Pass, I believe it requires backend on the same system. Proprietary Codec Support. Check to enable, Apply… & Apply… System Updates. No action necessary, will be a part of the Ubuntu update mechanism. Themes and Artwork. For themes, I selected Enable/Update all. Apply… & Apply… Infrared & Startup behavior and Plugins. Defer until you know more. Close software centre. Open mythTV (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythTV". Might be a good idea to drag and drop the mythTV icon to the terminal, it's easy to get rid of later. Incorrect Group Membership. Fix this by clicking "Yes"… Log out/end. Do this by clicking "Yes"… For my Lenovo S12, I had to manually restart Ubuntu - and still with the very long restart…/no start/cold boot/reboot/pressing the shift key required Open mythTV (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythTV". Might be a good idea to drag and drop the mythTV icon to the terminal, it's easy to get rid of later. Will open with Select country & language. Do so. then get message with "No", hit "Ok" and arrive at the data base Configuration 1/2 screen. You will need your brackend password, from backend ? Setup General Database Configuration 1/2 Password:~? Enter this Hit Alt-n to go to the next page. Select "Use custom id…", then enter a custom ID, I use the machine's name. Hit finish, and MythTV should start up with all default settings. For the lenovo S12, the first thing you want to do is to set Playback profiles to "Normal". From Setup TV Settings Playback Alt-N(ext) Alt-N(ext) Playback Profiles (3/8) : Change Current Video Playback Profile to "Normal". You can fiddle with this setting later. For the lenovo S12, the second thing is to get the sound going. From Setup General Alt-N(ext) Alt-N(ext) Alt-N(ext) Audio System: The top of the screen is a button title "Scan for audio devices", move the highlight there and press the Space bar. Then Tab down to Audio Output Device: and left-right arrow until "ALSA:hw:Card=Intel,DEV=0" is selected. Then Alt-N(ext) until "Finish". Now you should have sound. You should now have MythTV working nicely on the Lenovo S12 Notes about wireless: Running Lenovo S12 on wireless is demanding on both power and WiFi connection. Best results will be obtained when running on power and wired connection. I run my S12 on wireless, actually two serial connections with two access points, something that is not easy to achieve. Here Mythbuntu client-server (in den) <? wireless link 1 <?office LAN? wireless link 2 <? Lenovo S12 Ubuntu 11.10 The office LAN is fixed IP behind an Untangle firewall router. There is another MythTV client on Ubuntu 10.10 computer in the office (which has always worked well). ProblemMythbuntu\Win7 client hangs with frozen frames, short segment of audio repeating. Hardware Rosewill RNX-G300EX IEEE 802.11b/g PCI Wireless Card on client-server 2 Linksys WRT54GL wireless broadband routers on LAN for link1 and link 2 WRT54GL FirmwareDD-WRT v24-sp2(07/22/09) voip set up to act as an access point. Note? many people advised this was an unworkable scheme, and in probably most cases it will be. Solution? Set up DD-WRT with the following Wireless settings… Basic Channel: Different fixed channels at least 4 difference, I use 6 & 11 Basic Sensitivity Range (ACK timing): 50 MAC filter use filter: Enable, Selected Permit only clients listed to access… Requires adding MAC addresses in "Edit MAC Filter List" This causes the 54GL's to ignore any but the listed MAC address, down side, no "guest" capability. Advanced Basic rate: All Advanced CTS Protection Mode: Off Advanced Frame Burst: Enable Advanced Max associate clients: 4 for client link 2, 1 for client-server link 1 Advanced AP isolation: Enable Advanced Preamble: Short Advanced Afterburner: On Advanced Wireless GUI access: Off Advanced WMM support: Off Other settings: default for supplied firmware. Why I suspect this worked? The 54GL Access Points's with the firmware's setting are set to handle a multiple client, wide area situation. With these mods I reconfigured them for a small area, few client situation, disabling Advanced WMM probably the most important. In addition, the client mythtv when used all other users of its access point are turned off except for a Skype phone. Also, the client-server is set up to allow other connections though it's LAN connection, and these are used to connect the TV and disc players, not used when client is being used.

  Read the article

• Optimizing a 3D World Javascript Animation

  - by johnny

  Hi! I've recently come up with the idea to create a tag cloud like animation shaped like the earth. I've extracted the coastline coordinates from ngdc.noaa.gov and wrote a little script that displayed it in my browser. Now as you can imagine, the whole coastline consists of about 48919 points, which my script would individually render (each coordinate being represented by one span). Obviously no browser is capable of rendering this fluently - but it would be nice if I could render as much as let's say 200 spans (twice as much as now) on my old p4 2.8 Ghz (as a representative benchmark). Are there any javascript optimizations I could use in order to speed up the display of those spans? One 'coordinate': <div id="world_pixels"> <span id="wp_0" style="position:fixed; top:0px; left:0px; z-index:1; font-size:20px; cursor:pointer;cursor:hand;" onmouseover="magnify_world_pixel('wp_0');" onmouseout="shrink_world_pixel('wp_0');" onClick="set_askcue_bar('', 'new york')">new york</span> </div> The script: $(document).ready(function(){ world_pixels = $("#world_pixels span"); world_pixels.spin(); setInterval("world_pixels.spin()",1500); }); z = new Array(); $.fn.spin = function () { for(i=0; i<this.length; i++) { /*actual screen coordinates: x/y/z --> left/font-size/top 300/13/0 300/6/300 | / |/ 0/13/300 ----|---- 600/13/300 /| / | 300/20/300 300/13/600 */ /*scale font size*/ var resize_x = 1; /*scale width*/ var resize_y = 2.5; /*scale height*/ var resize_z = 2.5; var from_left = 300; var from_top = 20; /*actual math coordinates: 1 -1 | / |/ 1 ----|---- -1 /| / | 1 -1 */ //var get_element = document.getElementById(); //var font_size = parseInt(this.style.fontSize); var font_size = parseInt($(this[i]).css("font-size")); var left = parseInt($(this[i]).css("left")); if (coast_line_array[i][1]) { } else { var top = parseInt($(this[i]).css("top")); z[i] = from_top + (top - (300 * resize_z)) / (300 * resize_z); //global beacause it's used in other functions later on var top_new = from_top + Math.round(Math.cos(coast_line_array[i][2]/90*Math.PI) * (300 * resize_z) + (300 * resize_z)); $(this[i]).css("top", top_new); coast_line_array[i][3] = 1; } var x = resize_x * (font_size - 13) / 7; var y = from_left + (left- (300 * resize_y)) / (300 * resize_y); if (y >= 0) { this[i].phi = Math.acos(x/(Math.sqrt(x^2 + y^2))); } else { this[i].phi = 2*Math.PI - Math.acos(x/(Math.sqrt(x^2 + y^2))); i } this[i].theta = Math.acos(z[i]/Math.sqrt(x^2 + y^2 + z[i]^2)); var font_size_new = resize_x * Math.round(Math.sin(coast_line_array[i][4]/90*Math.PI) * Math.cos(coast_line_array[i][0]/180*Math.PI) * 7 + 13); var left_new = from_left + Math.round(Math.sin(coast_line_array[i][5]/90*Math.PI) * Math.sin(coast_line_array[i][0]/180*Math.PI) * (300 * resize_y) + (300 * resize_y)); //coast_line_array[i][6] = coast_line_array[i][7]+1; if ((coast_line_array[i][0] + 1) > 180) { coast_line_array[i][0] = -180; } else { coast_line_array[i][0] = coast_line_array[i][0] + 0.25; } $(this[i]).css("font-size", font_size_new); $(this[i]).css("left", left_new); } } resize_x = 1; function magnify_world_pixel(element) { $("#"+element).animate({ fontSize: resize_x*30+"px" }, { duration: 1000 }); } function shrink_world_pixel(element) { $("#"+element).animate({ fontSize: resize_x*6+"px" }, { duration: 1000 }); } I'd appreciate any suggestions to optimize my script, maybe there is even a totally different approach on how to go about this. The whole .js file which stores the array for all the coordinates is available on my page, the file is about 2.9 mb, so you might consider pulling the .zip for local testing: metaroulette.com/files/31218.zip metaroulette.com/files/31218.js P.S. the php I use to create the spans: <?php //$arbitrary_characters = array('a','b','c','ddsfsdfsdf','e','f','g','h','isdfsdffd','j','k','l','mfdgcvbcvbs','n','o','p','q','r','s','t','uasdfsdf','v','w','x','y','z','0','1','2','3','4','5','6','7','8','9',); $arbitrary_characters = array('cat','table','cool','deloitte','askcue','what','more','less','adjective','nice','clinton','mars','jupiter','testversion','beta','hilarious','lolcatz','funny','obama','president','nice','what','misplaced','category','people','religion','global','skyscraper','new york','dubai','helsinki','volcano','iceland','peter','telephone','internet', 'dialer', 'cord', 'movie', 'party', 'chris', 'guitar', 'bentley', 'ford', 'ferrari', 'etc', 'de facto'); for ($i=0; $i<96; $i++) { $arb_digits = rand (0,45); $arbitrary_character = $arbitrary_characters[$arb_digits]; //$arbitrary_character = "."; echo "<span id=\"wp_$i\" style=\"position:fixed; top:0px; left:0px; z-index:1; font-size:20px; cursor:pointer;cursor:hand;\" onmouseover=\"magnify_world_pixel('wp_$i');\" onmouseout=\"shrink_world_pixel('wp_$i');\" onClick=\"set_askcue_bar('', '$arbitrary_character')\">$arbitrary_character</span>\n"; } ?>

  Read the article

• PC powers off at random times

  - by Timo Huovinen

  Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

  Read the article

• External USB drive is failing

  - by dma_k

  I have an external USB 2.0 drive WD My Book Mirror Edition, running in RAID 1 (mirroring) mode. A while ago the hard drive started to fail: it stops responding (directories are not listed returning an error after a big timeout). Sometimes it works for weeks before a failure, sometimes – few hours. Small write operations (like removing few files or editing a small file) do not harm, but when copying large files to the drive over the network, or creating the archive locally, the kernel dumps. Also interesting to note that once kernel has failed, Linux does not want to reboot normally (reboot hangs); when Linux box is shutdown with power button, WD drive does not go to sleep mode (as it usually does): leds continue to run, pressing and holding the "shutdown" button on drive's back panel does not do anything; only unplugging the power cord helps. Here goes the boot log: Aug 16 00:32:21 kernel: [ 1.514106] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Aug 16 00:32:21 kernel: [ 1.657738] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 1.673747] ehci_hcd 0000:00:1d.7: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 1.673751] ehci_hcd 0000:00:1d.7: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.725224] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 Aug 16 00:32:21 kernel: [ 1.741647] ehci_hcd 0000:00:1d.7: using broken periodic workaround Aug 16 00:32:21 kernel: [ 1.761790] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported Aug 16 00:32:21 kernel: [ 1.761873] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdfff000 Aug 16 00:32:21 kernel: [ 1.796043] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 Aug 16 00:32:21 kernel: [ 1.879069] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 Aug 16 00:32:21 kernel: [ 1.895446] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 1.911796] usb usb1: Product: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.928015] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd Aug 16 00:32:21 kernel: [ 1.944331] usb usb1: SerialNumber: 0000:00:1d.7 Aug 16 00:32:21 kernel: [ 1.961285] usb usb1: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 1.994412] hub 1-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.010864] hub 1-0:1.0: 8 ports detected Aug 16 00:32:21 kernel: [ 2.085939] uhci_hcd: USB Universal Host Controller Interface driver Aug 16 00:32:21 kernel: [ 2.191945] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 2.226029] uhci_hcd 0000:00:1d.0: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.226034] uhci_hcd 0000:00:1d.0: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.243237] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 Aug 16 00:32:21 kernel: [ 2.260390] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fe00 Aug 16 00:32:21 kernel: [ 2.277517] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.294815] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.312173] usb usb2: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.329534] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.346828] usb usb2: SerialNumber: 0000:00:1d.0 Aug 16 00:32:21 kernel: [ 2.412989] usb usb2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.430651] usb 1-2: new high speed USB device using ehci_hcd and address 2 Aug 16 00:32:21 kernel: [ 2.449046] hub 2-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.466514] hub 2-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.484639] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Aug 16 00:32:21 kernel: [ 2.537750] uhci_hcd 0000:00:1d.1: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.537756] uhci_hcd 0000:00:1d.1: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.555085] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 Aug 16 00:32:21 kernel: [ 2.572231] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fd00 Aug 16 00:32:21 kernel: [ 2.589593] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.606869] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.624134] usb usb3: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.641329] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.658505] usb usb3: SerialNumber: 0000:00:1d.1 Aug 16 00:32:21 kernel: [ 2.675843] usb usb3: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.692864] hub 3-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.709651] hub 3-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.727378] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Aug 16 00:32:21 kernel: [ 2.768252] uhci_hcd 0000:00:1d.2: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.768258] uhci_hcd 0000:00:1d.2: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.806679] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 Aug 16 00:32:21 kernel: [ 2.824117] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fc00 Aug 16 00:32:21 kernel: [ 2.841405] usb 1-2: New USB device found, idVendor=1058, idProduct=1104 Aug 16 00:32:21 kernel: [ 2.858448] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Aug 16 00:32:21 kernel: [ 2.875347] usb 1-2: Product: My Book Aug 16 00:32:21 kernel: [ 2.892113] usb 1-2: Manufacturer: Western Digital Aug 16 00:32:21 kernel: [ 2.908915] usb 1-2: SerialNumber: 575532553130303530353538 Aug 16 00:32:21 kernel: [ 2.943242] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.960405] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.977615] usb usb4: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.994687] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.011711] usb usb4: SerialNumber: 0000:00:1d.2 Aug 16 00:32:21 kernel: [ 3.029589] usb usb4: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.082027] sd 2:0:0:0: [sda] Attached SCSI disk Aug 16 00:32:21 kernel: [ 3.103953] usb 1-2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.122625] hub 4-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.140484] hub 4-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.161680] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 Aug 16 00:32:21 kernel: [ 3.181257] uhci_hcd 0000:00:1d.3: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 3.181263] uhci_hcd 0000:00:1d.3: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.198614] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 Aug 16 00:32:21 kernel: [ 3.216012] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fb00 Aug 16 00:32:21 kernel: [ 3.249877] Uniform CD-ROM driver Revision: 3.20 Aug 16 00:32:21 kernel: [ 3.267765] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 3.284947] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 3.302023] usb usb5: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.319215] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.336298] usb usb5: SerialNumber: 0000:00:1d.3 Aug 16 00:32:21 kernel: [ 3.368377] Initializing USB Mass Storage driver... Aug 16 00:32:21 kernel: [ 3.390652] usbcore: registered new interface driver hiddev Aug 16 00:32:21 kernel: [ 3.408109] scsi4 : SCSI emulation for USB Mass Storage devices Aug 16 00:32:21 kernel: [ 3.425281] sr 0:0:1:0: Attached scsi CD-ROM sr0 Aug 16 00:32:21 kernel: [ 3.438978] sr 0:0:1:0: Attached scsi generic sg0 type 5 Aug 16 00:32:21 kernel: [ 3.456328] usbcore: registered new interface driver usb-storage Aug 16 00:32:21 kernel: [ 3.474564] usb-storage: device found at 2 Aug 16 00:32:21 kernel: [ 3.474567] usb-storage: waiting for device to settle before scanning Aug 16 00:32:21 kernel: [ 3.475320] sd 2:0:0:0: Attached scsi generic sg1 type 0 Aug 16 00:32:21 kernel: [ 3.492587] USB Mass Storage support registered. Aug 16 00:32:21 kernel: [ 3.510930] usb usb5: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.531076] hub 5-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.548399] hub 5-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.591743] input: Western Digital My Book as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2:1.1/input/input2 Aug 16 00:32:21 kernel: [ 3.609515] generic-usb 0003:1058:1104.0001: input,hidraw0: USB HID v1.11 Device [Western Digital My Book] on usb-0000:00:1d.7-2/input1 Aug 16 00:32:21 kernel: [ 3.627466] usbcore: registered new interface driver usbhid Aug 16 00:32:21 kernel: [ 8.581664] usb-storage: device scan complete Aug 16 00:32:21 kernel: [ 8.624270] scsi 4:0:0:0: Direct-Access WD My Book 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.655135] scsi 4:0:0:1: Enclosure WD My Book Device 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.675393] sd 4:0:0:0: Attached scsi generic sg2 type 0 Aug 16 00:32:21 kernel: [ 8.698669] scsi 4:0:0:1: Attached scsi generic sg3 type 13 Aug 16 00:32:21 kernel: [ 8.723370] sd 4:0:0:0: [sdb] 1953513472 512-byte logical blocks: (1.00 TB/931 GiB) Aug 16 00:32:21 kernel: [ 8.750477] sd 4:0:0:0: [sdb] Write Protect is off Aug 16 00:32:21 kernel: [ 8.769411] sd 4:0:0:0: [sdb] Mode Sense: 10 00 00 00 Aug 16 00:32:21 kernel: [ 8.769414] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.822971] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.841978] sdb: sdb1 Aug 16 00:32:21 kernel: [ 8.905580] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.924173] sd 4:0:0:0: [sdb] Attached SCSI disk Aug 16 00:32:21 kernel: [ 11.600492] XFS mounting filesystem sdb1 Aug 16 00:32:21 kernel: [ 12.222948] Ending clean XFS mount for filesystem: sdb1 After a while the following appears in a log: Aug 16 09:30:56 kernel: [32359.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:31:59 kernel: [32422.112035] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:33:00 kernel: [32483.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 And then it is followed by few kernel dumps, which I think, are not good: Aug 16 09:33:40 kernel: [32520.428027] INFO: task xfssyncd:1002 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32520.462689] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32520.497422] xfssyncd D c3d84a60 0 1002 2 0x00000000 Aug 16 09:33:40 kernel: [32520.532117] f6c9aa80 00000046 c1132742 c3d84a60 00000286 c1418100 c1418100 00000000 Aug 16 09:33:40 kernel: [32520.566867] f6c9ac3c c2808100 00000000 f653b18b 00001d76 00000001 f6c9aa80 c3c3f0e0 Aug 16 09:33:40 kernel: [32520.601343] 08e59242 f6c9ac3c 2e41392b 00000000 08e59242 00000000 c3f7fb48 0067385a Aug 16 09:33:40 kernel: [32520.635533] Call Trace: Aug 16 09:33:40 kernel: [32520.668991] [<c1132742>] ? cfq_set_request+0x0/0x290 Aug 16 09:33:40 kernel: [32520.702804] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32520.736555] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32520.770360] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32520.804110] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32520.837713] [<c1128230>] ? blk_peek_request+0x135/0x143 Aug 16 09:33:40 kernel: [32520.871265] [<f8582987>] ? scsi_dispatch_cmd+0x185/0x1e5 [scsi_mod] Aug 16 09:33:40 kernel: [32520.904407] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32520.937007] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32520.969033] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.000485] [<c10cffd1>] ? bio_add_page+0x28/0x2e Aug 16 09:33:40 kernel: [32521.031403] [<f8918d38>] ? _xfs_buf_ioapply+0x206/0x22b [xfs] Aug 16 09:33:40 kernel: [32521.061888] [<f89197bd>] ? xfs_buf_iorequest+0x38/0x60 [xfs] Aug 16 09:33:40 kernel: [32521.091845] [<f8907230>] ? xlog_bdstrat_cb+0x16/0x3d [xfs] Aug 16 09:33:40 kernel: [32521.121222] [<f8905781>] ? XFS_bwrite+0x32/0x64 [xfs] Aug 16 09:33:40 kernel: [32521.150007] [<f89059be>] ? xlog_sync+0x20b/0x311 [xfs] Aug 16 09:33:40 kernel: [32521.178214] [<f89112fc>] ? xfs_trans_ail_tail+0x12/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.205914] [<f8906261>] ? xlog_state_sync_all+0xa2/0x141 [xfs] Aug 16 09:33:40 kernel: [32521.233074] [<f8906611>] ? _xfs_log_force+0x51/0x68 [xfs] Aug 16 09:33:40 kernel: [32521.259664] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32521.285662] [<f8906636>] ? xfs_log_force+0xe/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.311171] [<f89202df>] ? xfs_sync_worker+0x17/0x5c [xfs] Aug 16 09:33:40 kernel: [32521.336117] [<f891fbb7>] ? xfssyncd+0x134/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.360498] [<f891fa83>] ? xfssyncd+0x0/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.384211] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32521.407890] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32521.430876] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32521.453394] INFO: task flush-8:16:12945 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32521.476116] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32521.498579] flush-8:16 D 00000000 0 12945 2 0x00000000 Aug 16 09:33:40 kernel: [32521.520649] f4e4d540 00000046 e412e940 00000000 00000002 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32521.542426] f4e4d6fc c2808100 00000000 00000000 000008b4 00000001 f4e4d540 c3c3f0e0 Aug 16 09:33:40 kernel: [32521.563745] 02e905a8 f4e4d6fc 007a5399 00000000 02e905a8 00000000 f4e2db48 00670b98 Aug 16 09:33:40 kernel: [32521.585077] Call Trace: Aug 16 09:33:40 kernel: [32521.605790] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32521.626184] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32521.646133] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32521.665659] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32521.684716] [<f891796e>] ? xfs_convert_page+0x30a/0x331 [xfs] Aug 16 09:33:40 kernel: [32521.703366] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32521.721644] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32521.739465] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.756896] [<c10cfa45>] ? bio_alloc_bioset+0x7b/0xba Aug 16 09:33:40 kernel: [32521.774046] [<f8917af0>] ? xfs_submit_ioend_bio+0x3b/0x44 [xfs] Aug 16 09:33:40 kernel: [32521.790694] [<f8917ba3>] ? xfs_submit_ioend+0xaa/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.806736] [<f891817d>] ? xfs_page_state_convert+0x5c0/0x61c [xfs] Aug 16 09:33:40 kernel: [32521.822859] [<c113705b>] ? __lookup_tag+0x8e/0xee Aug 16 09:33:40 kernel: [32521.838958] [<f891840d>] ? xfs_vm_writepage+0x91/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.855039] [<c108bbcc>] ? __writepage+0x8/0x22 Aug 16 09:33:40 kernel: [32521.871067] [<c108c17b>] ? write_cache_pages+0x1af/0x29f Aug 16 09:33:40 kernel: [32521.886616] [<c108bbc4>] ? __writepage+0x0/0x22 Aug 16 09:33:40 kernel: [32521.901593] [<c108c285>] ? generic_writepages+0x1a/0x21 Aug 16 09:33:40 kernel: [32521.916455] [<f8918338>] ? xfs_vm_writepages+0x0/0x38 [xfs] Aug 16 09:33:40 kernel: [32521.931484] [<c108c2a5>] ? do_writepages+0x19/0x25 Aug 16 09:33:40 kernel: [32521.946648] [<c10c80d9>] ? writeback_single_inode+0xc7/0x273 Aug 16 09:33:40 kernel: [32521.961675] [<c10c8c44>] ? writeback_inodes_wb+0x3dd/0x49c Aug 16 09:33:40 kernel: [32521.976831] [<c10c8e18>] ? wb_writeback+0x115/0x178 Aug 16 09:33:40 kernel: [32521.991778] [<c10c901f>] ? wb_do_writeback+0x121/0x131 Aug 16 09:33:40 kernel: [32522.006538] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32522.021091] [<c10c9050>] ? bdi_writeback_task+0x21/0x89 Aug 16 09:33:40 kernel: [32522.035493] [<c10979e5>] ? bdi_start_fn+0x59/0xa4 Aug 16 09:33:40 kernel: [32522.049765] [<c109798c>] ? bdi_start_fn+0x0/0xa4 Aug 16 09:33:40 kernel: [32522.063792] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32522.077612] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32522.091260] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32522.104966] INFO: task smartctl:13098 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32522.118883] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32522.133012] smartctl D 00000020 0 13098 13097 0x00000000 Aug 16 09:33:40 kernel: [32522.147221] e50b9540 00000086 c11d28a8 00000020 00000770 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32522.161720] e50b96fc c2808100 00000000 e53e8800 00000000 00000020 c3cec000 c13886c0 Aug 16 09:33:40 kernel: [32522.176217] f99dab68 e50b96fc 007a4f1e 00000001 c4082f24 c4082ed8 00000001 c3c3f0e0 Aug 16 09:33:40 kernel: [32522.190737] Call Trace: Aug 16 09:33:40 kernel: [32522.205038] [<c11d28a8>] ? __netdev_alloc_skb+0x14/0x2d Aug 16 09:33:40 kernel: [32522.219605] [<c126b799>] ? schedule_timeout+0x20/0xb0 Aug 16 09:33:40 kernel: [32522.234144] [<c112820d>] ? blk_peek_request+0x112/0x143 Aug 16 09:33:40 kernel: [32522.248649] [<f85873b6>] ? scsi_request_fn+0x3c1/0x47a [scsi_mod] Aug 16 09:33:40 kernel: [32522.263233] [<c103aba8>] ? del_timer+0x55/0x5c Aug 16 09:33:40 kernel: [32522.277773] [<c126b6a2>] ? wait_for_common+0xa4/0x100 Aug 16 09:33:40 kernel: [32522.292342] [<c102cd8d>] ? default_wake_function+0x0/0x8 Aug 16 09:33:40 kernel: [32522.306958] [<c112b3d1>] ? blk_execute_rq+0x8b/0xb2 Aug 16 09:33:40 kernel: [32522.321569] [<c112b2ac>] ? blk_end_sync_rq+0x0/0x23 Aug 16 09:33:40 kernel: [32522.336070] [<c112b58b>] ? blk_recount_segments+0x13/0x20 Aug 16 09:33:40 kernel: [32522.350583] [<c1127307>] ? blk_rq_bio_prep+0x44/0x74 Aug 16 09:33:40 kernel: [32522.365059] [<c112b0b2>] ? blk_rq_map_kern+0xc5/0xee Aug 16 09:33:40 kernel: [32522.379439] [<c112e2a5>] ? sg_scsi_ioctl+0x221/0x2aa Aug 16 09:33:40 kernel: [32522.393801] [<c112e672>] ? scsi_cmd_ioctl+0x344/0x39a Aug 16 09:33:40 kernel: [32522.408140] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.422566] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.436832] [<f87676aa>] ? sd_ioctl+0x90/0xb5 [sd_mod] Aug 16 09:33:40 kernel: [32522.451228] [<c112c35f>] ? __blkdev_driver_ioctl+0x53/0x63 Aug 16 09:33:40 kernel: [32522.465689] [<c112cbbf>] ? blkdev_ioctl+0x850/0x891 Aug 16 09:33:40 kernel: [32522.479982] [<c1020474>] ? __wake_up_common+0x34/0x59 Aug 16 09:33:40 kernel: [32522.494138] [<c10244cd>] ? complete+0x28/0x36 Aug 16 09:33:40 kernel: [32522.507986] [<c1086c64>] ? find_get_page+0x1f/0x81 Aug 16 09:33:40 kernel: [32522.521671] [<c10abed5>] ? add_partial+0xe/0x40 Aug 16 09:33:40 kernel: [32522.535285] [<c1086e68>] ? lock_page+0x8/0x1d Aug 16 09:33:40 kernel: [32522.548797] [<c1087432>] ? filemap_fault+0xb5/0x2e6 Aug 16 09:33:40 kernel: [32522.562141] [<c109941c>] ? __do_fault+0x381/0x3b1 Aug 16 09:33:40 kernel: [32522.575441] [<c10d0c30>] ? block_ioctl+0x27/0x2c Aug 16 09:33:40 kernel: [32522.588708] [<c10d0c09>] ? block_ioctl+0x0/0x2c Aug 16 09:33:40 kernel: [32522.601858] [<c10bcd78>] ? vfs_ioctl+0x1c/0x5f Aug 16 09:33:40 kernel: [32522.614917] [<c10bd30c>] ? do_vfs_ioctl+0x4aa/0x4e5 Aug 16 09:33:40 kernel: [32522.627961] [<c10350db>] ? __do_softirq+0x115/0x151 Aug 16 09:33:40 kernel: [32522.640901] [<c126e270>] ? do_page_fault+0x2f1/0x307 Aug 16 09:33:40 kernel: [32522.653803] [<c10bd388>] ? sys_ioctl+0x41/0x58 Aug 16 09:33:40 kernel: [32522.666674] [<c10030fb>] ? sysenter_do_call+0x12/0x28 Then again few messages reset high speed USB device using ehci_hcd and address 2. I have browsed and read similar error reports here and there and I tried: I have upgraded the kernel from v2.6.26-2 to 2.6.32-5, which has not solved the problem. They say, this might a cable problem. I have tried to replace the USB-to-miniUSB cable (that connects external drive with computer) with another one. No changes. Somebody suggests to try another USB port. I have only 4 external USB ports, tried another one with no success. They say to try uhci_hcd. I have unmounted the device, unloaded ehci_hcd and mounted again. The difference was that now in log I get reset full speed USB device using uhci_hcd and address 2 and similar kernel dumps after a while. They say to echo 128 > /sys/block/sdb/device/max_sectors. I tried it with ehci_hcd with no success (note: I have issued this command after the drive was mounted but before using it actively). I have lauched smartmond and checking periodically the output of smartctl: drive temperature is OK, number of bad sectors and uncorrectable errors is 0. Nothing suspicious is reported by S.M.A.R.T. except maybe the following: Aug 16 12:40:12 kernel: [43715.314566] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Aug 16 12:40:13 kernel: [43715.705622] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Of course, I have not tried all combinations of above. But unfortunately, I am run out of cardinal ideas. If anybody can advice something specific about the problem, you are very welcome.

  Read the article

< Previous Page | 2 3 4 5 6