Search Results

Search found 333 results on 14 pages for 'ipsec'.

Page 6/14 | < Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >

• Openswan + xl2tpd connections time out after a while

  - by Halfgaar

  I have a non-NATed Openswan+xl2tpd server (Ubuntu 12.04), to which I connect with a Windows 8 behind NAT. The client loses its connection after a while of doing nothing (between 30 and 60 minutes, but I didn't time it). The client doesn't have enabled that it should kill inactive connections. Nor does it ever go into sleep mode. I also tried setting the kill-after-time to 24 hours, but that didn't help. The NAT router behind which the client located is Debian Linux, and its router is a Cisco which connects us directly to the data center where the server is. None of our other connections, like SSH, get dropped with inactivity (because of cheap routers). I did however try turning on the keepalives in /etc/ipsec.conf: config setup (...snip...) nat_traversal=yes force_keepalive=yes keep_alive=10 but that didn't help. As you can see in the config later, dead peer detection's action is clear. That would be a first suggestion to fix, but I need clear, because people will be connecting from everwhere but the kitchen sink. Besides, as I said, in the test setup I have now, I can't see any device killing its connection. (edit: 'restart' also has the same effect) These are of one time it happened: Jul 18 16:18:06 host xl2tpd[1918]: Maximum retries exceeded for tunnel 49070. Closing. Jul 18 16:18:06 host xl2tpd[1918]: Terminating pppd: sending TERM signal to pid 18359 Jul 18 16:18:06 host xl2tpd[1918]: Connection 4 closed to 89.188.x.y, port 1701 (Timeout) Jul 18 16:18:11 host xl2tpd[1918]: Unable to deliver closing message for tunnel 49070. Destroying anyway. and these on another: Jul 18 17:44:39 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:43 xl2tpd[1918]: last message repeated 4 times Jul 18 17:44:43 host xl2tpd[1918]: Maximum retries exceeded for tunnel 10918. Closing. Jul 18 17:44:43 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:43 host xl2tpd[1918]: Terminating pppd: sending TERM signal to pid 26338 Jul 18 17:44:43 host xl2tpd[1918]: Connection 6 closed to 89.188.x.y, port 1701 (Timeout) Jul 18 17:44:44 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:48 xl2tpd[1918]: last message repeated 3 times Jul 18 17:44:48 host xl2tpd[1918]: Unable to deliver closing message for tunnel 10918. Destroying anyway. Jul 18 17:44:59 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:44:59 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:09 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:09 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:19 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:19 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:29 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:29 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:39 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:39 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:49 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:49 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Versions: Ubuntu 12.04 Openswan: 2.6.37-1 xl2tpd: 3.1+dfsg-1 kernel: 3.2.0-49-generic configs: /etc/ipsec.conf: version 2.0 # conforms to second version of ipsec.conf specification config setup nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v4:!10.152.2.0/24 oe=off protostack=netkey force_keepalive=yes keep_alive=10 conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=2 rekey=no dpddelay=30 dpdtimeout=120 dpdaction=clear ikelifetime=8h keylife=1h type=transport left=%defaultroute leftprotoport=17/1701 right=%any rightprotoport=17/%any /etc/xl2tpd/xl2tpd.conf [global] ipsec saref = no [lns default] ip range = 10.152.2.2-10.152.2.254 local ip = 10.152.2.1 refuse chap = yes refuse pap = yes require authentication = yes ppp debug = no pppoptfile = /etc/ppp/options.xl2tpd length bit = yes /etc/ppp/options.xl2tpd: require-mschap-v2 refuse-mschap ms-dns 10.152.2.1 asyncmap 0 auth crtscts idle 1800 mtu 1200 mru 1200 lock hide-password local #debug name l2tpd proxyarp lcp-echo-interval 30 lcp-echo-failure 4

  Read the article

• L2TP server on OpenVZ

  - by MikO

  I need to create a L2TP VPN server on a VPS in a OpenVZ container (I can install CentOS5, CentOS6, Ubuntu12.04 or Debian6). I have been reading and I think IPSEC does not work on OpenVZ, is this right? In fact I´m getting an error saying that it's not allowed in the kernel... But an important thing is that I don't have any security requirement at all for the transmissions I'll be doing. So, is there something I can do? Is there any way to set up a L2TP server without IPSEC?

  Read the article

• How do you implement NAT-T passthrough on a Juniper SRX series Firewall?

  - by Chris

  We have 3 juniper SRX-100 firewalls, they are configured like so: FW1 - FW2 - INTERNET - FW3 We would like to create an IPSEC tunnel between FW3 and FW1 passing through FW2 preferably using NAT-T. Is this possible? FW1 and FW2 have some strict access rules only allowing 1 port connected (it's a DMZ with a server in) so we can't just create a route based vpn between FW1 and FW2 to forward the traffic (otherwise all traffic will be forwarded) We know the tunnel is fine because we have managed to test it between FW1 and FW3 (without FW2 in the middle) so we know that the issue is to do with the 'passthrough' on FW2. Essentially, the question is - What options do we need to select on FW2 to enable it to pass through the IPSEC traffic straight to FW1? Many thanks in advance

  Read the article

• Duplicate of IPSEC certificate template not displaying

  - by Tim Brigham

  I am working on getting IPSEC working on computers outside my domain. I am unable to get a duplicate of the IPSec Offline Request template to show on the web interface. My CA is 2008 R2 Enterprise and the permissions on the template should be adequate to allow me access (my account has read and enroll). If I publish the original template it functions as desired. I also have other custom templates in use (although using autoenrollment). The duplicate is almost identical to the original, excepting that it has a longer validity period and the private key is marked as exportable. How do I debug at this point?

  Read the article

• Cisco ASA 5505 site to site IPSEC VPN won't route from multiple LANs

  - by franklundy

  Hi I've set up a standard site to site VPN between 2 ASA 5505s (using the wizard in ASDM) and have the VPN working fine for traffic between Site A and Site B on the directly connected LANs. But this VPN is actually to be used for data originating on LAN subnets that are one hop away from the directly connected LANs. So actually there is another router connected to each ASA (LAN side) that then route to two completely different LAN ranges, where the clients and servers reside. At the moment, any traffic that gets to the ASA that has not originated from the directly connected LAN gets sent straight to the default gateway, and not through the VPN. I've tried adding the additional subnets to the "Protected Networks" on the VPN, but that has no effect. I have also tried adding a static route to each ASA trying to point the traffic to the other side, but again this hasn't worked. Here is the config for one of the sites. This works for traffic to/from the 192.168.144.x subnets perfectly. What I need is to be able to route traffic from 10.1.0.0/24 to 10.2.0.0/24 for example. ASA Version 8.0(3) ! hostname Site1 enable password ** encrypted names name 192.168.144.4 Site2 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.144.2 255.255.255.252 ! interface Vlan2 nameif outside security-level 0 ip address 10.78.254.70 255.255.255.252 (this is a private WAN circuit) ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! passwd ** encrypted ftp mode passive access-list inside_access_in extended permit ip any any access-list outside_access_in extended permit icmp any any echo-reply access-list outside_1_cryptomap extended permit ip 192.168.144.0 255.255.255.252 Site2 255.255.255.252 access-list inside_nat0_outbound extended permit ip 192.168.144.0 255.255.255.252 Site2 255.255.255.252 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-603.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 access-group inside_access_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 10.78.254.69 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute dynamic-access-policy-record DfltAccessPolicy aaa authentication ssh console LOCAL http server enable http 0.0.0.0 0.0.0.0 outside http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs crypto map outside_map 1 set peer 10.78.254.66 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal telnet timeout 5 ssh 0.0.0.0 0.0.0.0 outside ssh timeout 5 console timeout 0 management-access inside threat-detection basic-threat threat-detection statistics port threat-detection statistics protocol threat-detection statistics access-list group-policy DfltGrpPolicy attributes vpn-idle-timeout none username enadmin password * encrypted privilege 15 tunnel-group 10.78.254.66 type ipsec-l2l tunnel-group 10.78.254.66 ipsec-attributes pre-shared-key * ! ! prompt hostname context

  Read the article

• Site to Site VPN with Fault Tolerence

  - by Nordberg

  Hello, I have a situation where I require an IPSEC tunnel between two sites. Site 2 is a small branch office with basic (ADSL) connectivity and Site 1 is the "main" office with SDSL and ADSL for redundancy should the SDSL fail. From Site 1, all traffic bound for the 172.0.0.0 network will then be sent down another IPSEC tunnel to a supplier's Remote Server. See this page for the basic premise (this is a rough idea and things can be moved about etc...) I am considering specifying Cisco ASA devices as the firewalls for both sites for all connections. Would it be possible to employ something like HSRC to provide a backup at Site 1 should the SDSL go down? I suppose the key aims here are that Site 2 can somehow failover to initiate a VPN to the ASA behind the ADSL at Site 1. I will have a 21 subnet mask on all internet connections so can play with Class C routing if need be... If I'm barking up the wrong tree with HSRC, is there another way I can acheive this without massive expenditure on Barracuda routers et al? Many Thanks.

  Read the article

• Passing OpenVPN road-warrior traffic through tunnel pfsense

  - by Chris

  I have a local LAN (10.100.100.0/24) and OpenVPN road-warriors (10.99.99.0/24). pfSense is regulating all this as follows: LAN: 10.100.100.105 WAN: 10.100.99.1 (connected to DSL Router which connects to internet). OPT1: 10.99.99.0 (OpenVPN tun0). There is an IPSec connection between my office and another office where my LAN can work on a specific IP address (sql server to be exact) on 192.168.30.41. My problem is that I wish my OpenVPN road-warrior clients to be able to use the IPSec service on 192.168.30.41 as well (which at present they cannot despite the fact that I am pushing the route 192.168.30.0 255.255.255.0). The other site's administrator cannot add the extra route for my openvpn clients for a lot of reasons which I am not going to enter at this stage. Is there a possibility that I could NAT all of my openVPN road-warriors requests through a local LAN IP address (something like 10.100.100.250 which is not used by anything on my LAN). The problem is that I am a newbie with pfSense so as much step-by-step help as possible would be very much appreciated! Thank you. C.

  Read the article

• IPSec tunnelling with ISA Server 2000...

  - by Izhido

  Believe it or not, our corporate network still uses ISA Server 2000 (in a Windows Server 2003 machine) to enable / control Internet access to / from it. I was asked recently to configure that ISA Server to create a site-to-site VPN for a new branch in a office about 25 km. away from it. The idea is basically to enable not only computers, but also Palm devices (WiFi-enabled, of course), to be able to see other computers in both sites. I was also told that a simple VPN-enabled wireless AP/router (in this case, a Cisco WRV210 unit) should be enough to establish communications with the main office. To be fair, the router looks easy to configure; it was confusing at first, but further understanding of how site-to-site VPNs work cleared all doubts about it. Now I need to make modifications to our ISA Server in order to recognize the newly installed & configured "remote" VPN site. Thing is, either my Googling skills are pathethically horrible, or there doesn't seem to be much (or any, at all) information about how to configure an ISA Server 2000 for this purpose. Lots of stuff on 2004, of course; also, I think I saw something for 2006. But nothing I could find about 2000. Reading about 2004, it seems that the only way I can do site-on-site with a Cisco router (read: a non-ISA-Server machine) is through something they call a "IPSec tunnel". Fair enough. However, I can't figure for the life of me how could I even start to find, leave alone configure, such a thing. Do you, people, happen to know how to do IPSec tunelling on a ISA Server 2000, so I can connect to a Cisco WRV210 VPN-enabled router, and build a site-to-site VPN for both networks? Or is this not possible at all? (Meaning I should change anything in this configuration to make it work...)

  Read the article

• Routing subnet over GRE tunnel

  - by eMgz

  Hi, Im trying to configure a GRE over IPSec connection between two subnets. The IPSec tunnel is opened and now I want to add a GRE tunnel over it: ip tunnel add GRE01 mode gre remote 10.244.0.1 local 10.244.245.32 ttl 255 ip link set GRE01 up ip addr add 10.244.248.126 dev GRE01 ip route add 10.244.248.125 dev GRE01 Now I have an interface GRE01 (ifconfig): GRE10 Link encap:UNSPEC HWaddr <h_addr> inet addr:10.244.248.126 P-t-P:10.244.248.126 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MTU:1476 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And the following routes (ip route list): 10.244.248.125 dev GRE10 scope link <pub_subnet> dev eth0 proto kernel scope link src <pub_ip> default via <pub_gw> dev eth0 metric 100 As a last step, I need now to route my subnet over the tunnel: ip route add 10.245.1.224/28 10.244.248.125 However, I am getting the error Error: either "to" is duplicate, or "10.244.248.125" is a garbage. So, what I didn't understand is why I can't route my subnet over the tunnel, once the only route I have there says that it should route the tunnel IP over the GRE01 interface. Any hint? Thanks.

  Read the article

• Connect to a Fortinet VPN with Ubuntu

  - by Dan

  I don't know a lot about VPNs but I'd like to connect to a Fortinet VPN with Ubuntu. I can connect on Windows using Forticlient just by entering the policy server (vpn.theserver.com) and then it asks for a user/password. I use IPSec.

  Read the article

• Netgear FVS336G as VPN Server

  - by Farseeker

  Hi All, One of our offices has made the move away from PFSense to a Netgear FVS336G. The one feature I can't seem to figure out is its VPN capabilities. I'm confused as to whether this device can act as a IPSEC VPN server, or if it can only act as the client in a Site-Site VPN. The documentation does not make this clear at all, and Google does not seem to have been any help. (Related question: here)

  Read the article

• StrongSwan + xl2tpd client timeout between 2-5 minutes

  - by Howard Guo

  I run CentOS 6.4 on Amazon EC2, using xl2tpd-1.3.1 from EPEL repository together with StrongSwan 5.0.4. I setup a simple IPSec connection: conn l2tp type=transport keyexchange=ikev1 rekey=no authby=psk leftsubnet=0.0.0.0/0 rightsubnet=0.0.0.0/0 compress=yes auto=add And here is xl2tpd.conf: [global] ipsec saref = yes [lns default] ip range = 192.168.0.2-192.168.0.250 local ip = 192.168.0.1 ppp debug = yes pppoptfile = /etc/ppp/options.xl2tpd length bit = yes Here is options.xl2tpd: ms-dns 8.8.4.4 auth lock debug proxyarp There is only one client - Android 4.2 Android connects successfully: Oct 27 19:45:02 ip-172-31-17-30 xl2tpd[2706]: Connection established to x.x.x.x, 59578. Local: 18934, Remote: 29291 (ref=0/0). LNS session is 'default' Oct 27 19:45:02 ip-172-31-17-30 xl2tpd[2706]: Call established with x.x.x.x, Local: 36452, Remote: 29845, Serial: -1369754322 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: pppd 2.4.5 started by howard, uid 0 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: Using interface ppp0 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: Connect: ppp0 <--> /dev/pts/0 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: peer from calling number x.x.x.x authorized Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: Deflate (15) compression enabled Oct 27 19:45:03 ip-172-31-17-30 pppd[2709]: Cannot determine ethernet address for proxy ARP Oct 27 19:45:03 ip-172-31-17-30 pppd[2709]: local IP address 192.168.0.1 Oct 27 19:45:03 ip-172-31-17-30 pppd[2709]: remote IP address 192.168.0.2 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] 192.168.0.1 appeared on ppp0 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] 192.168.0.1 disappeared from ppp0 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] 192.168.0.1 appeared on ppp0 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] interface ppp0 activated In the meanwhile, Internet works perfectly on the Android client, the VPN connection is stable and fast. However, it always happens that within 2-5 minutes after the connection is established: Oct 27 19:47:07 ip-172-31-17-30 xl2tpd[2706]: Maximum retries exceeded for tunnel 18934. Closing. Oct 27 19:47:07 ip-172-31-17-30 xl2tpd[2706]: Connection 29291 closed to 95.91.227.224, port 59578 (Timeout) Oct 27 19:47:07 ip-172-31-17-30 charon: 06[KNL] interface ppp0 deactivated Oct 27 19:47:07 ip-172-31-17-30 charon: 06[KNL] interface ppp0 deleted Then the VPN connection is broken. So what might have gone wrong? The same L2TP service works flawlessly on iOS 7, MacOS 10.8, and Windows 7, there is no disconnection issue on those OSes. Thank you!

  Read the article

• secure data transport between web server and database server

  - by atypicalgeek

  I asked this question in stackoverflow and it was suggested to try here so here goes... I'm planning on provisioning a web server and database server in a server farm environment. They will be in the same network but not in the same domain, both windows server 2008 and the database server is sql server 2008. My question being, what is the best way to secure data in transport between the servers? I've looked into IPSEC and SSL but not sure how to go about implementing either.

  Read the article

• Setting up Windows 2008 VPN Server

  - by Ivan Vovnenko

  Hi, i'm trying to setup windows 2008 server as a L2TP/IPSEC VPN server (PPTP is not secure), to receive windows (xp+) and Mac connections. The win2008 is behind the router. Can anyone provide easy step-by-step instructions? I tries several tutorial but no luck. Also VPN clients setup both on mac and windows would be very helpful. Thanks in advance.

  Read the article

• L2TP and multiple interfaces on the machine

  - by Alex

  We have setup ipsec and l2tp on linux. One question came up (due to firewall management policy) is whether it's possible to have 1 virtual interface instead of one per connected client. Now we have: ppp0 serverip clientip1 ppp1 serverip clientip2 Want to have: l2tp_tun serverip serverip like with OpenVPN's tun interfaces and then to be able to push IP address and route to each client.

  Read the article

• Best security practice for small networks - wifi, lan,

  - by Grimlockz

  We regularly setup small networks for clients in different locations to allow them to work on different products now the question what should be the best security practice. Currently we have a wifi enabled with WPA2 and most laptops connect to this but some will connect to a cabled switch connecting to the router. We are thinking on what we should do to increase the security on our small networks - We do have have security on the laptops so you can share directly to the other persons drive by a simple Windows user account. Some suggestions are: We get a LAN switch with ACL control and mac filtering for the hard wired connections? We get acl working on the wifi via a good Cisco router? ipSec policies on all machines? IP filtering and fixed IPs? I suppose people are worried that anyone can plug into the switches and get the access to the network . Summary: Maintain a level of decent security that can be replicated easily to every setup that we do for clients

  Read the article

• racoon-tool doesn't generate full racoon.conf file in /var/lib/racoon/racoon.conf

  - by robthewolf

  I am using ipsec-tools/racoon to create my VPN. I am using racoon-tool to configure racoon.conf but when I run racoon-tool reload it only generates the first section - Global items. When I run racoon-tool I get: # racoon-tool reload Loading SAD and SPD... SAD and SPD loaded. Configuring racoon...done. This is the entire file /var/lib/racoon/racoon.conf # # Racoon configuration for Samuel # Generated on Wed Jan 5 21:31:49 2011 by racoon-tool # # # Global items # path pre_shared_key "/etc/racoon/psk.txt"; path certificate "/etc/racoon/certs"; log debug; I cannot find anywhere a solution as to why this is happening. Please help

  Read the article

• how to connect public web server to internal LAN

  - by DefSol

  I have a VPS which is my public web server for all my clients. It's running server 2008 and I would like to have it connect via secure connection to my internal LAN. I would like this to be a route so access is bi-derectional. Have read about Server & Domain isolation, but am concerned this may prevent public views to the webs sites on the server. I currently have a PPTP tunnel, but I'm wanting better security (IPSec or SSL etc) and it's not given my bi derectional access. (In fact my backups aren't copying accross but this could be an acl issue) The goal is to provide easy/automated backups of data & sql db's to my internal LAN, as well as a means to provision new sites & db's from a workflow occuring internally. Internal lan is windows based with ISA 2006 at the perimeter. Thanks

  Read the article

• racoon-tool doesn't generate full racoon.conf file in /var/lib/racoon/racoon.conf

  - by robthewolf

  I am using ipsec-tools/racoon to create my VPN. I am using racoon-tool to configure racoon.conf but when I run racoon-tool reload it only generates the first section - Global items. When I run racoon-tool I get: # racoon-tool reload Loading SAD and SPD... SAD and SPD loaded. Configuring racoon...done. This is the entire file /var/lib/racoon/racoon.conf # # Racoon configuration for Samuel # Generated on Wed Jan 5 21:31:49 2011 by racoon-tool # # # Global items # path pre_shared_key "/etc/racoon/psk.txt"; path certificate "/etc/racoon/certs"; log debug; I cannot find anywhere a solution as to why this is happening. Please help

  Read the article

• Cisco ASA 5505 (8.05): asymmetrical group-policy filter on an L2L IPSec tunnel

  - by gravyface

  I'm trying to find a way to setup a bi-directional L2L IPSec tunnel, but with differing group-policy filter ACLs for both sides. I have the following filter ACL setup, applied, and working on my tunnel-group: access-list ACME_FILTER extended permit tcp host 10.0.0.254 host 192.168.0.20 eq 22 access-list ACME_FILTER extended permit icmp host 10.0.0.254 host 192.168.0.20 According to the docs, VPN filters are bi-directional, you always specify the remote host first (10.0.0.254), followed by the local host and (optionally) port number, as per the documentation. However, I do not want the remote host to be able to access my local host's TCP port 22 (SSH) because there's no requirement to do so -- there's only a requirement for my host to access the remote host's SFTP server, not vice-versa. But since these filter ACLs are bidirectional, line 1 is also permitting the remote host to access my host's SSH Server. The documentation I'm reading doesn't seem to clear to me if this is possible; help/clarification much appreciated.

  Read the article

• FreeBSD's VPN & Mac OS X IPSecuritas

  - by alexus

  I need to be able to VPN in to my FreeBSD server from my Mac using IPSecuritas. I was wondering if anyone ever done something, I'm reading VPN over IPsec but that mainly covers if you had 2 nodes with 2 public IP address. My endpoint in IPSecuritas configured with MODE_CFG enabled so it'll have the other node to query my address from it's coming from. SSH is out of question, this is not a VPN solution, people who'd end up using VPN wouldn't know what to do, so I need very simple VPN the one that you get to use almost anywhere, you have a client and you have server, client makes a connection to server and boom, you in...

  Read the article

• Fortigate VPN Routing issue

  - by user1571299

  I have 200B Fortigate unit with 2 internet WAN connections. I also have a remote site which I'm connected to via IPSEC VPN through WAN1. This site has only one GW IP address. I'd also like to setup a VPN ontop of WAN2 with that specific site as it's destination. The default route for my end is WAN1. My problem is I cant figure out how to have both tunnels up at the same time. What's the best practice for achieving this? Thanks

  Read the article

• Trying to get a new user up on VPN

  - by Chris

  Caveat: I am not a sysadmin, so please forgive the n00bness of the query. We have a new user and I'm trying to get them up on VPN. We use pfsense as an IPSEC endpoint. This person is using Shrewsoft for the client. I had created an entry in pfsense for them and then edited a previous user's config file. Shrewsoft didn't import the config file very well and I had to hand edit the information. Now we are getting gateway errors. One thing I've noticed is that there is a different between the values of the preshared key stored on the firewall and the psk stored in the config file. I assume it has something to do with a hash, but I've no idea if that's the case and whether that might be what's causing the problem. Any suggestions greatly appreciated! Tangentially, is there some software used to generate these config files?

  Read the article

• Just how slow should my VPN be?

  - by David Heggie

  I have a VPN setup between a remote office with 2 ADSL connections (8Mb downstream, 512Kb upstream) and a main office with a 10Mb EFM connection (10Mb both up and down). The VPN is an IPSec connection using a DrayTek 2930 router for the ADSL and a DrayTek 3200 router at the EFM end. However, I'm unable to get speeds over this connection (tested with iperf) of anything over 600Kb or so down from the main office (traffic will pretty much always be from the main office to the remote office) Whilst I realise that there is an overhead and I'm never going to get the "full" bandwidth available over this VPN, I'd like to think that there's something I should be looking at that may help improve it. I've tried using the DrayTek's built-in "VPN Trunking" features which are supposed to load-balance connections, but this doesn't seem to improve matters much. I guess my question is - is this the kind of performance I should expect from this kind of setup and I'll just have to live with it, or should I be able to squeeze something more out of it through some VPN magic?

  Read the article

• VPN IPsec site 2 site and static routing

  - by Giacomo

  Hello everybody experts! My question is pretty simple, but I can't figure it out because I'm pretty noob with these network stuffs. I have a vpn IPsec site2site between 2 lan with different ip classes, LAN A is class C and LAN B is class A. The vpn presents the LAN A to LAN B with the 10.178.51.64/27 segment. The problem is that when I start the vpn connection I cant Ping any 10.174.0.0/24 address(LAN B remote segment) from my LAN A; I think I need some kind of static route. Could u help me out pls? Thx Regards

  Read the article

< Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >