Search Results

Search found 255 results on 11 pages for 'lsusb'.

Page 6/11 | < Previous Page | 2 3 4 5 6 7 8 9 10 11  | Next Page >

• ARM Debian (squeeze) USB driver with mismatch 3.3.3 kernel but /lib/modules/2.6.36

  - by frank

  Hei guys, my sheevaplug embedded server works fine, but when I wanted to use USB, the device gets not attached to /dev/tty/USB0 lsusb shows correctly: Bus 001 Device 002: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port an modprobe usbserial raises: FATAL: Could not load /lib/modules/3.3.3/modules.dep: No such file or directory in the /lib/modules/ Folder there is instead a 2.6.36-Folder uname -r gives 3.3.3 How can I overcome this mismatch? Can I create a symlink? I can't flash this embedded device since it is deployed somewhere, only ssh? Please advise!

  Read the article

• modprobe ndiswrapper - not found

  - by David

  I'm trying to use ndiswrapper on a Slackware 12 (I think) box, but I'm running into a problem with modprobe. Everything I find online says that it should be working, but for some unknown reason it isn't. Here's what I've done so far: Installed ndiswrapper (latest tarball, make, make install) Ran ndiswrapper -i on the WinXP driver for my USB wireless card Ran ndiswrapper -l which tells me the driver is present and the device is present (lsusb also confirms the device is present) Ran ndiswrapper -m which put an alias for wlan0 in /etc/modprobe.d/ndiswrapper.conf Ran depmod -a Ran modprobe ndiswrapper which tells me "FATAL: module ndiswrapper not found" Ran modprobe -l which shows no listing for ndiswrapper I even tossed in a reboot or two while trying various combinations of the above, still nothing. So naturally ifconfig wlan0 up isn't working because the device isn't being created, presumably because the module isn't loading the driver. Does anybody have any suggestions? Everything points to the notion that this should work fine, but modprobe just isn't able to find what it needs. Have I missed an important step?

  Read the article

• How do I unmount a charging device in Linux?

  - by PeanutsMonkey

  I have a mobile device attached via USB to a Linux box and wish to unmount it. I ran the command fdisk -l however it does not list a mount point. I then ran the command lsusb which yielded the screenshot below. I then proceeded to search the /dev/disk/by-id directory and was found the following file The file is a symbolic link to what appears to be /dev/sdc Questions Why does it not appear when I run the command fdisk -l? How do I unmount it properly without simply yanking the USB cord from the USB port?

  Read the article

• How to configure a Logitech USB headset on Fedora 14 [closed]

  - by Humble Debugger

  I have a Logitech USB headset http://www.amazon.com/gp/product/B003NREDG4 but I can't hear anything nor input anything through it. I am working on a Fedora 14 desktop. cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xfebdc000 irq 51 2 [Headset ]: USB-Audio - Logitech USB Headset Logitech Logitech USB Headset at usb-0000:00:1d.0-2, full speed /sbin/lsmod | grep -c snd 14 lsusb Bus 008 Device 002: ID 046d:c529 Logitech, Inc. Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 004: ID 046d:0a0b Logitech, Inc. ClearChat Pro USB Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Please advise

  Read the article

• How to use a D-Link usb network adapter on debian

  - by Barranka

  I have a Debian (squeeze) desktop, and I need to use a D-Link 150 USB Wireless Network Adapter. So far I've done this: $ lsusb ... Bus 001 Device 006: ID 2001:3c18 D-Link Corp. ... After looking for a solution in google, I found that I needed to install the following package: firmware-ralink_0.28+squeeze1_all.deb I've installed it, but Debian doesn't want to find the adapter. When I run lsmod, I can't find what I'm supposed to find: rt2870sta Can you point me in the right direction?

  Read the article

• USB webcam just works once and next time I've to reboot

  - by user30262

  I'm using Ubuntu 9.10, and a usb webcam that is shown as 'Bus 001 Device 005: ID 0ac8:3450 Z-Star Microelectronics Corp.' by lsusb. The problem is that on connecting the cam, it just works with the first program I start (skype, tokbox, messenger), and if I disconnect it or switch to another program, it stops to work and I have to restart my computer to make it work again. Has anyone else noticed this behaviour? Is there some good solution to reset the camera without rebooting to make it work again?

  Read the article

• Ubuntu 12.04 LTS Wireless Asus USB-N53 (rt3572sta) driver installation issue

  - by Jake Thompson

  My purchase of the Asus USB-N53 just came in today and I spent several hours Googling and researching drivers for this device. When I first plugged the device in it connected fine to my open system, WEP, DHCP configured access point. I opened Google Chrome and a few pages loaded, everything seemed fine. 30 seconds later... Boom! It disconnected and showed attempts to reconnect and asked for the WEP key and just showed a state of infinite connection time until it asked me for the password again. I'm using amd64 (64 bit Ubuntu desktop 12.04 LTS) The official driver can be found here although I had no luck with it. lsusb: Bus 003 Device 002: ID 0b05:179d ASUSTek Computer, Inc. uname -a Linux Jake 3.2.0-31-generic #50-Ubuntu SMP Fri Sep 7 16:16:45 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux ----------------------------------------------------------------------------------Solved: I must of done something wrong when I originally installed the latest drivers from the chipset manufacturers website. I tried reinstalling and did modprobe rt3572sta and waited maybe 10 minutes??? and I connected then I rebooted and everything seems to be working so far. What I did do before hand is unplug the device and typed into the terminal (once for every source I attempted to install): cd '<directory of the driver source>' make uninstall make clean Then I went into the 2.5.0.0 directory and installed that with make make install Then I typed modprobe rt3572sta This was all in superuser. For those who don't know: sudo su

  Read the article

• Wireless will not connect

  - by azz0r

  Hello, I have installed Ubuntu 10.10 on the same machine as my windows setup. However, it will not connect to my wireless network. It can see its there, it can attempt to connect, yet it will never connect. It will keep bringing up the password prompt everyso often. I have tried turning my security to WEP, I ended up turning it back to WPA2. It is set to AES (noted a few threads on google about that). Can you assist? I would love to dive into Ubuntu, but without the internet its pointless. --- lshw -C network --- *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 00:1d:92:ea:cc:62 capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8168 driverversion=8.020.00-NAPI duplex=half latency=0 link=no multicast=yes port=twisted pair resources: irq:29 ioport:e800(size=256) memory:feaff000-feafffff memory:f8ff0000-f8ffffff(prefetchable) memory:feac0000-feadffff(prefetchable) *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: 00:15:af:72:a4:38 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bgn --- iwconfig ---- lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Wuggawoo" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Tx-Power=9 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on --- cat /etc/network/interfaces ---- auto lo iface lo inet loopback logs deamon.log --- Jan 19 04:17:09 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:17:09 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:09 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:11 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:11 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:11 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): association took too long. Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 5 -> 6 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): asking for new secrets Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled... Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started... Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 6 -> 4 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled... Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete. Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting... Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 4 -> 5 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): connection 'Wuggawoo' has security, and secrets exist. No new secrets needed. Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'ssid' value 'Wuggawoo' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'scan_ssid' value '1' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'key_mgmt' value 'WPA-PSK' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'psk' value '<omitted>' Jan 19 04:17:12 ubuntu NetworkManager: nm_setting_802_1x_get_pkcs11_engine_path: assertion `NM_IS_SETTING_802_1X (setting)' failed Jan 19 04:17:12 ubuntu NetworkManager: nm_setting_802_1x_get_pkcs11_module_path: assertion `NM_IS_SETTING_802_1X (setting)' failed Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete. Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: set interface ap_scan to 1 Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:13 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:13 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:13 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:23 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:17:23 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:23 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:24 ubuntu AptDaemon: INFO: Initializing daemon Jan 19 04:17:25 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:25 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:25 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:27 ubuntu NetworkManager: <info> wlan0: link timed out. --- kern.log --- Jan 19 04:18:11 ubuntu kernel: [ 142.420024] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out Jan 19 04:18:13 ubuntu kernel: [ 144.333847] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:13 ubuntu kernel: [ 144.539996] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:13 ubuntu kernel: [ 144.750027] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:14 ubuntu kernel: [ 144.940022] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out Jan 19 04:18:25 ubuntu kernel: [ 155.832995] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:25 ubuntu kernel: [ 156.030046] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:25 ubuntu kernel: [ 156.230039] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:25 ubuntu kernel: [ 156.430039] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out --- syslog --- Jan 19 04:18:46 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:18:46 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:18:46 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:18:48 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:18:48 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:18:48 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:18:48 ubuntu kernel: [ 178.833905] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:48 ubuntu kernel: [ 179.030035] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:48 ubuntu kernel: [ 179.230020] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:48 ubuntu kernel: [ 179.433634] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out lspci and lsusb lspci -- 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:02.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:00.0 VGA compatible controller: nVidia Corporation G80 [GeForce 8800 GTS] (rev a2) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 03:00.0 FireWire (IEEE 1394): JMicron Technology Corp. IEEE 1394 Host Controller -- lsusb -- Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 003: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser Bus 004 Device 002: ID 045e:0730 Microsoft Corp. Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 13d3:3247 IMC Networks 802.11 n/g/b Wireless LAN Adapter Bus 002 Device 002: ID 0718:0628 Imation Corp. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 046d:08c2 Logitech, Inc. QuickCam PTZ Bus 001 Device 002: ID 0424:2228 Standard Microsystems Corp. 9-in-2 Card Reader Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub With no security on my router I still can't connect, I get: Jan 19 15:58:01 ubuntu wpa_supplicant[1165]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 15:58:01 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 15:58:01 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: WPS-AP-AVAILABLE Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: Association request to the driver failed Jan 19 15:58:02 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 15:58:05 ubuntu NetworkManager: <info> wlan0: link timed out. Jan 19 15:58:07 ubuntu wpa_supplicant[1165]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 15:58:07 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 15:58:07 ubuntu NetworkManager: <info> (wlan0): supplicant connec

  Read the article

• Bluetooth not working on an Alienware m14x r2

  - by S. L.

  on my alienware m14x r2 laptop with ubuntu 12.04.1 x64, the bluetooth interface is not working. WLAN works fine. I have a dualboot install with ubuntu & win 7 on this laptop. In win 7, the bluetooth interface works fine, because its all activated in BIOS. I have the killer wireless-n 1202 a/g/n interface with integrated bluetooth 4.0 in this laptop. Here is some code : sudo rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 064e:8128 Suyin Corp. Bus 002 Device 003: ID 0cf3:3004 Atheros Communications, Inc. Bus 002 Device 004: ID 187c:0521 Alienware Corporation dmesg | grep "Bluetooth" [ 2.590377] Bluetooth: Core ver 2.16 [ 2.590395] Bluetooth: HCI device and connection manager initialized [ 2.590397] Bluetooth: HCI socket layer initialized [ 2.590399] Bluetooth: L2CAP socket layer initialized [ 2.590403] Bluetooth: SCO socket layer initialized [ 2.591518] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.591519] Bluetooth: BNEP filters: protocol multicast [ 2.599411] Bluetooth: RFCOMM TTY layer initialized [ 2.599415] Bluetooth: RFCOMM socket layer initialized [ 2.599416] Bluetooth: RFCOMM ver 1.11 [ 2.696552] Bluetooth: Generic Bluetooth USB driver ver 0.6 [ 2.696751] Bluetooth: Atheros AR30xx firmware driver ver 1.0 [ 2.702607] Bluetooth: Configuration file not found ar3k/ramps_0x11020000_40.dfu [ 2.702609] Bluetooth: Loading sysconfig file failed Any ideas to fix that problem ?

  Read the article

• No USB 04b4:0307 mike input after 10.04

  - by Papou

  I am using an USB phone that is in fact a so-called "sound card" based on the 04b4:0307 chip. In fact, I have two different phones using 04b4:0307 and in fact I have a sound USB key too. This, I believe, is the start of why they call 04b4:0307 "ubiquitous" (instead of oh four bee...). But not "eternal". The mike worked in Ubuntu 9.10 and 10.04 but not later ([email protected]). "not working" means that 04b4:0307 shows in Sound Preference but that its vu-meter is mute. I have posted the full lsusb and the result of tests in various systems here: http://www.papou.byethost9.com/tmp/1043601.html Note: Tests done on VirtualBox (thankfully). But UbuntUnity no longer works on VB, so I used the LinuxMint equivalent. ?hat's fate. I could not find any problem report close enough. What should be my next step? I believe the problem occurs in module snd-usb-audio. One thing I might try if I knew how is hacking a DEB with its 10.04's source. I can hack DEBs. Any hint welcome on how to make a DEB overriding a kernel packed module. I mean that the newly installed module should have precedence, be loaded instead, the module installed with the kernel. TIA !

  Read the article

• Is there a Generic USB TouchScreen Driver 12.04?

  - by lbjoum

  Is there a Generic USB TouchScreen Driver 12.04? Device 03eb:201c I've been looking for 4 days solid (not very skilled) and can't find a solution. I have a generic tablet: C97- Atom N2600 9.7" 2GB 32GB Bluetooth WiFi WebCam Ext.3G Windows 7 Tablet PC Using 12.04 and cannot find a driver. I installed android and the touchscreen works but still lots of other bugs. Oh well, stuck with Windows 7 and not happy about it. Will keep trying, but too much time wasted already. If you have a solution I would love to try it. ubuntu@ubuntu:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 0cf2:6238 ENE Technology, Inc. Bus 001 Device 003: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB Bus 001 Device 005: ID 05e1:0100 Syntek Semiconductor Co., Ltd 802.11g + Bluetooth Wireless Adapter Bus 001 Device 006: ID 090c:3731 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) Bus 003 Device 002: ID 03eb:201c Atmel Corp. at90usbkey sample firmware (HID mouse) (from Windows: HID\VID_03EB&PID_201C\6&5F38127&0&0000 USB\VID_03EB&PID_201C\5&193ADADC&1&2 ) Bus 001 Device 007: ID 0518:0001 EzKEY Corp. USB to PS2 Adaptor v1.09 Bus 001 Device 008: ID 192f:0916 Avago Technologies, Pte. ubuntu@ubuntu:~$ sudo lsusb -v Bus 003 Device 002: ID 03eb:201c Atmel Corp. at90usbkey sample firmware (HID mouse) Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 32 idVendor 0x03eb Atmel Corp. idProduct 0x201c at90usbkey sample firmware (HID mouse) bcdDevice 45.a2 iManufacturer 1 CDT iProduct 2 9.75 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 34 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x00 (Missing must-be-set bit!) (Bus Powered) MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 0 No Subclass bInterfaceProtocol 0 None iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.11 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 177 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0020 1x 32 bytes bInterval 5 Device Status: 0x00fb Self Powered Remote Wakeup Enabled Debug Mode ubuntu@ubuntu:~$ sudo lshw ubuntu description: Notebook product: To be filled by O.E.M. (To be filled by O.E.M.) vendor: To be filled by O.E.M. version: To be filled by O.E.M. serial: To be filled by O.E.M. width: 32 bits capabilities: smbios-2.7 dmi-2.7 smp-1.4 smp configuration: boot=normal chassis=notebook cpus=2 family=To be filled by O.E.M. sku=To be filled by O.E.M. uuid=00020003-0004-0005-0006-000700080009 *-core description: Motherboard product: Tiger Hill vendor: INTEL Corporation physical id: 0 version: To be filled by O.E.M. serial: To be filled by O.E.M. slot: To be filled by O.E.M. *-firmware description: BIOS vendor: American Megatrends Inc. physical id: 0 version: 4.6.5 date: 08/24/2012 size: 64KiB capacity: 960KiB capabilities: pci upgrade shadowing cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer acpi usb biosbootspecification *-cpu:0 description: CPU product: Intel(R) Atom(TM) CPU N2600 @ 1.60GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: 6.6.1 serial: 0003-0661-0000-0000-0000-0000 slot: CPU 1 size: 1600MHz capacity: 1600MHz width: 64 bits clock: 400MHz capabilities: x86-64 boot fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx constant_tsc arch_perfmon pebs bts nonstop_tsc aperfmperf pni dtes64 monitor ds_cpl est tm2 ssse3 cx16 xtpr pdcm movbe lahf_lm arat configuration: cores=2 enabledcores=1 id=2 threads=2 *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 24KiB capacity: 24KiB capabilities: internal write-back unified *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 512KiB capacity: 512KiB capabilities: internal varies unified *-logicalcpu:0 description: Logical CPU physical id: 2.1 width: 64 bits capabilities: logical *-logicalcpu:1 description: Logical CPU physical id: 2.2 width: 64 bits capabilities: logical *-logicalcpu:2 description: Logical CPU physical id: 2.3 width: 64 bits capabilities: logical *-logicalcpu:3 description: Logical CPU physical id: 2.4 width: 64 bits capabilities: logical *-memory description: System Memory physical id: 28 slot: System board or motherboard size: 2GiB *-bank:0 description: SODIMM [empty] product: [Empty] vendor: [Empty] physical id: 0 serial: [Empty] slot: DIMM0 *-bank:1 description: SODIMM DDR3 Synchronous 800 MHz (1.2 ns) vendor: 69 physical id: 1 serial: 00000210 slot: DIMM1 size: 2GiB width: 64 bits clock: 800MHz (1.2ns) *-cpu:1 physical id: 1 bus info: cpu@1 version: 6.6.1 serial: 0003-0661-0000-0000-0000-0000 size: 1600MHz capabilities: ht configuration: id=2 *-logicalcpu:0 description: Logical CPU physical id: 2.1 capabilities: logical *-logicalcpu:1 description: Logical CPU physical id: 2.2 capabilities: logical *-logicalcpu:2 description: Logical CPU physical id: 2.3 capabilities: logical *-logicalcpu:3 description: Logical CPU physical id: 2.4 capabilities: logical *-pci description: Host bridge product: Atom Processor D2xxx/N2xxx DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 03 width: 32 bits clock: 33MHz *-display UNCLAIMED description: VGA compatible controller product: Atom Processor D2xxx/N2xxx Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 32 bits clock: 33MHz capabilities: pm msi vga_controller bus_master cap_list configuration: latency=0 resources: memory:dfe00000-dfefffff ioport:f100(size=8) *-multimedia description: Audio device product: N10/ICH 7 Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 02 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:42 memory:dff00000-dff03fff *-pci:0 description: PCI bridge product: N10/ICH 7 Family PCI Express Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: 02 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:2000(size=4096) memory:80000000-801fffff ioport:80200000(size=2097152) *-usb:0 description: USB controller product: N10/ICH 7 Family USB UHCI Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:23 ioport:f0a0(size=32) *-usb:1 description: USB controller product: N10/ICH 7 Family USB UHCI Controller #2 vendor: Intel Corporation physical id: 1d.1 bus info: pci@0000:00:1d.1 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:19 ioport:f080(size=32) *-usb:2 description: USB controller product: N10/ICH 7 Family USB UHCI Controller #3 vendor: Intel Corporation physical id: 1d.2 bus info: pci@0000:00:1d.2 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:18 ioport:f060(size=32) *-usb:3 description: USB controller product: N10/ICH 7 Family USB UHCI Controller #4 vendor: Intel Corporation physical id: 1d.3 bus info: pci@0000:00:1d.3 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:16 ioport:f040(size=32) *-usb:4 description: USB controller product: N10/ICH 7 Family USB2 EHCI Controller vendor: Intel Corporation physical id: 1d.7 bus info: pci@0000:00:1d.7 version: 02 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:dff05000-dff053ff *-pci:1 description: PCI bridge product: 82801 Mobile PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: e2 width: 32 bits clock: 33MHz capabilities: pci subtractive_decode bus_master cap_list *-isa description: ISA bridge product: NM10 Family LPC Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 02 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: SATA controller product: N10/ICH7 Family SATA Controller [AHCI mode] vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 logical name: scsi0 version: 02 width: 32 bits clock: 66MHz capabilities: storage msi pm ahci_1.0 bus_master cap_list emulated configuration: driver=ahci latency=0 resources: irq:41 ioport:f0f0(size=8) ioport:f0e0(size=4) ioport:f0d0(size=8) ioport:f0c0(size=4) ioport:f020(size=16) memory:dff04000-dff043ff *-disk description: ATA Disk product: BIWIN SSD physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 1206 serial: 123403501060 size: 29GiB (32GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=8fbe402b *-volume:0 description: Windows NTFS volume physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 version: 3.1 serial: 249bde5d-8246-9a40-88c7-2d5e3bcaf692 size: 19GiB capacity: 19GiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2011-04-04 02:27:51 filesystem=ntfs state=clean *-volume:1 description: Windows NTFS volume physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 version: 3.1 serial: de12d40f-d5ca-8642-b306-acd9349fda1a size: 10231MiB capacity: 10GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2011-04-04 01:52:26 filesystem=ntfs state=clean *-serial UNCLAIMED description: SMBus product: N10/ICH 7 Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 02 width: 32 bits clock: 33MHz configuration: latency=0 resources: ioport:f000(size=32) *-scsi:0 physical id: 2 bus info: usb@1:1 logical name: scsi4 capabilities: emulated scsi-host configuration: driver=usb-storage *-disk description: SCSI Disk physical id: 0.0.0 bus info: scsi@4:0.0.0 logical name: /dev/sdb size: 29GiB (31GB) capabilities: partitioned partitioned:dos configuration: signature=00017463 *-volume description: Windows FAT volume vendor: mkdosfs physical id: 1 bus info: scsi@4:0.0.0,1 logical name: /dev/sdb1 logical name: /cdrom version: FAT32 serial: 129b-4f87 size: 29GiB capacity: 29GiB capabilities: primary bootable fat initialized configuration: FATs=2 filesystem=fat mount.fstype=vfat mount.options=rw,relatime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro state=mounted *-scsi:1 physical id: 3 bus info: usb@1:3.1 logical name: scsi6 capabilities: emulated scsi-host configuration: driver=usb-storage *-disk description: SCSI Disk physical id: 0.0.0 bus info: scsi@6:0.0.0 logical name: /dev/sdc size: 7400MiB (7759MB) capabilities: partitioned partitioned:dos configuration: signature=c3072e18 *-volume description: Windows FAT volume vendor: mkdosfs physical id: 1 bus info: scsi@6:0.0.0,1 logical name: /dev/sdc1 logical name: /media/JOUM8G version: FAT32 serial: e676-9311 size: 7394MiB capacity: 7394MiB capabilities: primary bootable fat initialized configuration: FATs=2 filesystem=fat label=Android mount.fstype=vfat mount.options=rw,nosuid,nodev,relatime,uid=999,gid=999,fmask=0022,dmask=0077,codepage=cp437,iocharset=iso8859-1,shortname=mixed,showexec,utf8,flush,errors=remount-ro state=mounted ubuntu@ubuntu:~$ ubuntu@ubuntu:~$ xinput list ? Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? Plus More Enterprise LTD. USB-compliant keyboard id=10 [slave pointer (2)] ? ? USB Optical Mouse id=11 [slave pointer (2)] ? Virtual core keyboard id=3 [master keyboard (2)] ? Virtual core XTEST keyboard id=5 [slave keyboard (3)] ? Power Button id=6 [slave keyboard (3)] ? Power Button id=7 [slave keyboard (3)] ? Sleep Button id=8 [slave keyboard (3)] ? Plus More Enterprise LTD. USB-compliant keyboard id=9 [slave keyboard (3)] ? USB 2.0 Webcam - Front id=12 [slave keyboard (3)] ? AT Translated Set 2 keyboard id=13 [slave keyboard (3)] ubuntu@ubuntu:~$

  Read the article

• Configure USB GSM Modem

  - by adisembiring

  I want to configure EVDO Usb Modem in Ubuntu 10.10 I insert my usb modem to laptop and check the usb is detected or not using $sudo lsusb and the result is: Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 201e:2009 Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 14cd:6600 Super Top USB 2.0 IDE DEVICE Bus 002 Device 002: ID 201e:2009 is my us device. and than I execute command $dmesg | grep -e tty [ 0.000000] console [tty0] enabled [ 818.054660] usb 2-1.3: GSM modem (1-port) converter now attached to ttyUSB0 [ 818.055125] usb 2-1.3: GSM modem (1-port) converter now attached to ttyUSB1 [ 818.055647] usb 2-1.3: GSM modem (1-port) converter now attached to ttyUSB2 [ 818.330641] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0 [ 818.330743] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 [ 818.330840] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2 [ 1054.917473] usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB0 [ 1054.917995] usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB1 [ 1054.918481] usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB2 [ 1055.214087] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0 [ 1055.214221] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 [ 1055.214356] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2 Why converter disconnected from ttyUSB2 ? and than I try to execute command $sudo wvdialconf sorry, no modem was detected! Is it in use by another program ? did you configure it properly with setserials ? I change the same type usb modem from my friend, but I still get error above.

  Read the article

• Configure EVDO USB Modem in Ubuntu 10.10

  - by adisembiring

  I want to configure EVDO Usb Modem in Ubuntu 10.10 I insert my usb modem to laptop and check the usb is detected or not using $sudo lsusb and the result is: Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 201e:2009 Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 14cd:6600 Super Top USB 2.0 IDE DEVICE Bus 002 Device 002: ID 201e:2009 is my us device. and than I execute command $dmesg | grep -e tty [ 0.000000] console [tty0] enabled [ 818.054660] usb 2-1.3: GSM modem (1-port) converter now attached to ttyUSB0 [ 818.055125] usb 2-1.3: GSM modem (1-port) converter now attached to ttyUSB1 [ 818.055647] usb 2-1.3: GSM modem (1-port) converter now attached to ttyUSB2 [ 818.330641] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0 [ 818.330743] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 [ 818.330840] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2 [ 1054.917473] usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB0 [ 1054.917995] usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB1 [ 1054.918481] usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB2 [ 1055.214087] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0 [ 1055.214221] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 [ 1055.214356] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2 Why converter disconnected from ttyUSB2 ? and than I try to execute command $sudo wvdialconf sorry, no modem was detected! Is it in use by another program ? did you configure it properly with setserials ? I change the same type usb modem from my friend, but I still get error above.

  Read the article

• Hancon / Hanwang Graphics Tablet not recognised

  - by Martin Kyle

  I'm totally lost. I've just built a new system and installed Ubuntu 12.04. It's my first time with Linux and getting into the terminal / command line for the first time since IBMDOS 5 and Windows 3.1 has been a steep learning curve. However, the interface works beautifully apart from it doesn't recognize my Hanvon Artmaster AM1209. I have sent diagnostics to Digimend and Favux was kind enough to advise that the tablet should be using the Wacom X driver as the Hanvon is actually a Hanwang and these should be supported. lsusb reports: ID 0b57:8501 Beijing HanwangTechnology Co., Ltd xinput list reports: ? Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? PS/2+USB Mouse id=8 [slave pointer (2)] ? Virtual core keyboard id=3 [master keyboard (2)] ? Virtual core XTEST keyboard id=5 [slave keyboard (3)] ? Power Button id=6 [slave keyboard (3)] ? Power Button id=7 [slave keyboard (3)] ? Eee PC WMI hotkeys id=9 [slave keyboard (3)] ? AT Translated Set 2 keyboard id=10 [slave keyboard (3)] Favux suggested inspecting /var/log/Xorg.0.log for the tablet but I cannot see any mention of it, and that is as far as I have got. I've tried researching the problem but I am struggling with all the new terminology and the fact that I want the PC to be a means to an end and not the end in itself where I spend the rest of my days tweaking and testing rather than just using it. Hope there is some help out there.

  Read the article

• USB Mouse and Keyboard not working in Linux 4 Tegra

  - by Sijo

  I am a new person in Tegra Linux development. I have Tamontem NG Evaluation board with Tegra 3 Chip. I installed L4T sample file system from NVIDIA tegra Resources (https://developer.nvidia.com/linux-tegra) and installed the file system as described in the documentation provided in NVIDIA site. Already these was an SD card with L4T running. i dont want to change the boot loader. So I copied the boot.scr.uimg to root (/) folder and uImage to boot(/boot/) and it starts booting from the existing SD card. After that while booting, some errors occurred in some Bluetooth devices (there is no bluetooth device in the board). So I disabled Bluetooth by giving the following command sudo mv /etc/init/bluetooth.conf /etc/init/bluetooth.conf.noexec Now the problem is that mouse and keyboard are not working. So i cannot login. Even though i installed desktop, the mouse and keyboard are not working. But mouse and keyboard are enumerating. lsusb command is showing the USB mouse and keyboard. The installed file system is Ubuntu 13.04. Linux Kernel version is 3.1 What to do. Please help.Thanks in Advance.

  Read the article

• CMOTECH D-50 modem installation in Ubuntu 12.04

  - by Ricardo

  I have recently upgraded from 10.04 to 12.04. I had installed a 3G D-50 modem from CMOTECH. The program for Debian is provided by a Swedish company (ice.net). Usually after some mambo jambo of installung the libg++ libraries requested you can install it and runned in Ubuntu 8.04, 9.04, 10.04 and as far as I know in 11.04. When I upgraded and I click on the icon of ice.net it worked. However, I noticed that the usb D-50 modem was never mounted as usb and it didn't show up in the Lauchnpad or workspace (as when you plug a usb memory stick or another HD). I moved the icon from place in the launchpad and since when I click on the ice.net icon the same message appears: "please plug in your modem". The modem works (I've tested in Windows after this) and it blinks blue (sign that it works and picks up signal). If I type lsusb then I see that Ubuntu sees it on BUS address 006: Bus 006 Device 003: ID 16d8:6803 CMOTECH Co., Ltd. CNU-680 CDMA EV-DO modem I've tried wvdial without success. How can I get the D-50 usb modem mounted as in the previous versions of Ubuntu ?. Any help will be much appreciated. bests. Ricardo

  Read the article

• How do I make my USB Bluetooth dongle work in Ubuntu 11.04 ? (Can't init device hci0: Connection timed out (110)) [closed]

  - by MaikoID

  I've a USB bluetooth dongle root@maiko-cce-lin:~# lsusb | grep Bluetooth Bus 001 Device 007: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) that isn't working properly, hardly-ever it works but stops working in my next reboot. what I've tried it isn't software blocked root@maiko-cce-lin:~# rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: hci0: Bluetooth Soft blocked: no Hard blocked: no my device is recognized by hciconfig root@maiko-cce-lin:~# hciconfig -a hci0: Type: BR/EDR Bus: USB BD Address: 00:1F:81:00:01:1C ACL MTU: 1021:4 SCO MTU: 180:1 DOWN RX bytes:330 acl:0 sco:0 events:8 errors:0 TX bytes:24 acl:0 sco:0 commands:30 errors:22 Features: 0xff 0x3e 0x09 0x76 0x80 0x01 0x00 0x80 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: Link mode: SLAVE ACCEPT but I can't turn on my hci interface root@maiko-cce-lin:~# hciconfig hci up Can't init device hci0: Connection timed out (110) I don't understand why.. the hcitool command doesn't show any device. root@maiko-cce-lin:~# hcitool dev Devices: I've tried to restart my bluetooth service too with this command and make all these previous commands again but without success. root@maiko-cce-lin:~# service bluetooth restart * Stopping bluetooth [ OK ] * Starting bluetooth [ OK ] root@maiko-cce-lin:~# The dongle works if you disconnect it from usb, wait a few seconds and connect it again. so there must be better solution for it ( a solution not involving physically removing the dongle!)

  Read the article

• How to configure a MInimal Ubuntu installation?

  - by Uri Herrera

  I recently re installed Ubuntu using the mini.iso, but much to my dismay the mini.iso is not configured the same way as the Ubuntu desktop ISO some "problems" I'm facing such as: An Installation using the regular Ubuntu CD recognizes my active network connections in Network Manager, Installing with the mini.iso gives me a working connection however no connections are "active" in Network Manager displaying the message "The system network services are not compatible with this version." In a regular Ubuntu install connecting an Android phone to the PC mounts the phone's internal memory and sd card if present, Using the mini.iso the phone is detected as it appears with the command lsusb but it's not mounted and can't be mounted. In the same regards using the phone to tether it's connection to the PC via USB, the phone is connected to my (wifi) IN the regular Ubuntu install the phone is recognized as a networking device and is used as connection usb0, while in the mini.iso nothing happens, and trying to add the connection to /etc/network/interfaces results in the OS crashing. Just to make sure It wasn't a matter of my user not having the correct permissions or a lack of "groups", I've checked with an Ubuntu VM and the groups are the same, the networking files are the same, and the packages (except those of ubuntu-desktop such as Unity, Firefox, LibreOffice, and other non-essential software) are Installed in my PC, so what else is there to look for?. I'm sure I'm missing something, and I'd prefer not to install Ubuntu again, using the regular cd. How can I manage to get the same behaviour/configuration without reinstalling ?

  Read the article

• Can't configure Bluetooth drivers for mac mini 4,1

  - by t0dbld

  upon following the instructions on thread for mac mini leading to me to a thread for a fix for BlueTooth, i follow the instructions (even they are for other Mac's) i get it to fire up and combined with hcitool i managed to connect my apple track pad and keyboard... how ever upon reboot im back to bluetooth telling me there are no drivers nothing works, yet all the files are still there? This is driving me nuts and i caant figure out what i could be doing do you have any ideas what would make this happen ? lsusb results Bus 004 Device 007: ID 05ac:8218 Apple, Inc. Bus 004 Device 006: ID 05ac:820b Apple, Inc. Bus 004 Device 005: ID 05ac:820a Apple, Inc. Bus 004 Device 004: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth) Bus 004 Device 003: ID 05ac:8242 Apple, Inc. IR Receiver [built-in] Bus 004 Device 002: ID 03f0:1c24 Hewlett-Packard Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 054c:031f Sony Corp. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• After upgrading to 12.04 from 10.10 my mythbuntu standard MCEUSB remote no longer works

  - by keepitsimpleengineer

  I had no problems using my Windows Media Center Remote with 10.10 Mythbuntu, but after upgrading, it no longer affects Mythbuntu. I have verified and re-installed it in Mythbuntu Control Centre. I have used irw to verify the ir buttons actions are properly received by the HTPC. How do I go about fixing this? 3.2.0-26-generic (#41-Ubuntu SMP Thu Jun 14 17:49:24 UTC 2012) Xorg version: 1.11.3 (16 July 2012 08:06:31PM) GCC: 4.6 (x86_64-linux-gnu) Current updates as of 2012?07?21 $cat /etc/lirc/hardware.con #Chosen Remote Control REMOTE="Windows Media Center Transceivers/Remotes (all)" REMOTE_MODULES="lirc_dev mceusb" REMOTE_DRIVER="" REMOTE_DEVICE="/dev/lirc0" REMOTE_SOCKET="" REMOTE_LIRCD_CONF="mceusb/lircd.conf.mceusb" REMOTE_LIRCD_ARGS="" #Chosen IR Transmitter TRANSMITTER="None" TRANSMITTER_MODULES="" TRANSMITTER_DRIVER="" TRANSMITTER_DEVICE="" TRANSMITTER_SOCKET="" TRANSMITTER_LIRCD_CONF="" TRANSMITTER_LIRCD_ARGS="" #Enable lircd START_LIRCD="true" #Don't start lircmd even if there seems to be a good config file #START_LIRCMD="false" #Try to load appropriate kernel modules LOAD_MODULES="true" # Default configuration files for your hardware if any LIRCMD_CONF="" #Forcing noninteractive reconfiguration #If lirc is to be reconfigured by an external application #that doesn't have a debconf frontend available, the noninteractive #frontend can be invoked and set to parse REMOTE and TRANSMITTER #It will then populate all other variables without any user input #If you would like to configure lirc via standard methods, be sure #to leave this set to "false" FORCE_NONINTERACTIVE_RECONFIGURATION="false" START_LIRCMD="" # lsusb | grep -i infrared Bus 003 Device 002: ID 0471:0815 Philips (or NXP) eHome Infrared Receiver

  Read the article

• Ubuntu 12.04 problem with E160 huawei - can't detect the device and freezing system

  - by Matt

  I have just installed 12.04 and plugged in E160 and nothing happened - modem doesn't mount. I have found this solution : Ubuntu does not mount some Huawei devices due to bugs, problems etc. See if these work: 1st option: Connect the USB modem. After 10 seconds, type this in a terminal window: lsusb The output will be like this: Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 004: ID 12d1:140b Huawei Technologies Co., Ltd. Bus 004 Device 002: ID 413c:3016 Dell Computer Corp. Optical 5-Button Wheel Mouse Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 005: ID 0b97:7762 O2 Micro, Inc. Oz776 SmartCard Reader Bus 002 Device 004: ID 413c:8103 Dell Computer Corp. Wireless 350 Bluetooth Bus 002 Device 003: ID 0b97:7761 O2 Micro, Inc. Oz776 1.1 Hub Bus 002 Device 002: ID 413c:a005 Dell Computer Corp. Internal 2.0 Hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub The device is a Huawei modem, so let's look at the output. The relevant entry is: Bus 004 Device 004: ID 12d1:140b Huawei Technologies Co., Ltd Hence, you must type: sudo modprobe usbserial vendor=0x12d1 product=0x140b 2nd option Download usb-modeswitch and usb-modeswitch-data packages from packages.ubuntu.com. Install them through the command: sudo dpkg -i usb-modeswitch*.deb 3rd option Try a combination of both. but with no result. The modem is still not detected. I've tried to add a new connection but the system can't see my device in setup dialogue. Also I have noticed that when I open eg. terminal and try to type sth, the system freezes for a while.. Thanks for help!

  Read the article

• USB drives not recognized all of a sudden

  - by Siddharth

  I have tried most of the advice on askubuntu and other sites, usb_storage enable to fdisk -l. But I am unable to find steps to get it working again. lsusb results Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 413c:3012 Dell Computer Corp. Optical Wheel Mouse Bus 005 Device 002: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard Bus 001 Device 005: ID 8564:1000 dmseg | tail reports [ 69.567948] usb 1-4: USB disconnect, device number 4 [ 74.084041] usb 1-6: new high-speed USB device number 5 using ehci_hcd [ 74.240484] Initializing USB Mass Storage driver... [ 74.256033] scsi5 : usb-storage 1-6:1.0 [ 74.256145] usbcore: registered new interface driver usb-storage [ 74.256147] USB Mass Storage support registered. [ 74.257290] usbcore: deregistering interface driver usb-storage fdisk -l reports Device Boot Start End Blocks Id System /dev/sda1 * 2048 972656639 486327296 83 Linux /dev/sda2 972658686 976771071 2056193 5 Extended /dev/sda5 972658688 976771071 2056192 82 Linux swap / Solaris I think I need steps to install and get usb_storage module working. Edit : I tried sudo modprobe -v usb-storage reports sudo modprobe -v usb-storage insmod /lib/modules/3.2.0-48-generic-pae/kernel/drivers/usb/storage/usb-storage.ko Still no usb driver mounted. Nor does a device show up in /dev. Any step by step process to debug and fix this will be really helpful. Thanks.

  Read the article

• Wireless not working on desktop with Asus USB-N13 (B1) wireless adapter

  - by user900749

  I am trying to connect my desktop to a wireless network. I have purchased an ASUS USB-N13 B1 adapter. I have followed instructions for installing drivers and disabling conflicting drivers. I have thoroughly searched and could not find a solution. The adapter is recognized and powered on. I have entered the ssid and password information into the wireless network configuration. Other machines can connect to this wireless network, and the machine can connect online via ethernet without issue. Here is the output of some commands which summarize my configuration, and might give some clues : ~$ cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.1 LTS" ~$ uname -a Linux petra 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux ~$ lsusb Bus 001 Device 006: ID 0b05:17ab ASUSTek Computer, Inc. ~$ dmesg [ 1883.823150] wlan0: authenticate with 48:5b:39:e7:25:5e (try 1) [ 1884.020027] wlan0: authenticate with 48:5b:39:e7:25:5e (try 2) [ 1884.220025] wlan0: authenticate with 48:5b:39:e7:25:5e (try 3) [ 1884.420023] wlan0: authentication with 48:5b:39:e7:25:5e timed out Any assistance would be appreciated as I have been trying to get this machine online for several weeks now to no avail. Sincerely, Michael.

  Read the article

• How to run installation CD for second monitor?

  - by dobsoft

  I am running ubuntu 14 off of a live USB. I have a second monitor that I would like to use while using ubuntu. It has an installation cd that you have to install before using, and when I click on the .exe file the Archive Manager tries to open it and says an error occurred while loading the archive. Thanks for the help. Edit: additional information It just doesn't show up when when I'm in the display settings area. I press the locate(name is probably something else) monitor button too. I know it needs the CD because when I was using it with Windows it didn't work until I went through the installation process on the CD. If ubuntu doesn't use .exe files is there a way to use the CD still? Monitor info from label: -acer LCD monitor -model number: S200HQL Version: S200HQL bd I connect it to my computer using a VGA cord which is connected to a j5create VGA to USB adapter. Not sure if this helps: VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) lsusb output: Bus 002 Device 004: ID 046d:c52f Logitech, Inc. Unifying Receiver Bus 002 Device 005: ID 0bc2:2100 Seagate RSS LLC Bus 002 Device 007: ID 0711:5200 Magic Control Technology Corp. Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 1bcf:2c18 Sunplus Innovation Technology Inc. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• Ubuntu 12.04 problem with E160 huawei - can't detect the device nad freezing system

  - by Matt

  i just installed 12.04, plug in E160 and nothing happend - modem doesnt mount. i found this solution : Ubuntu does not mount some Huawei devices due to bugs, problems etc. See if these work: 1st option: Connect the USB modem. After 10 seconds, type this in a terminal window: lsusb The output will be like this: Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 004: ID 12d1:140b Huawei Technologies Co., Ltd. Bus 004 Device 002: ID 413c:3016 Dell Computer Corp. Optical 5-Button Wheel Mouse Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 005: ID 0b97:7762 O2 Micro, Inc. Oz776 SmartCard Reader Bus 002 Device 004: ID 413c:8103 Dell Computer Corp. Wireless 350 Bluetooth Bus 002 Device 003: ID 0b97:7761 O2 Micro, Inc. Oz776 1.1 Hub Bus 002 Device 002: ID 413c:a005 Dell Computer Corp. Internal 2.0 Hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub The device is a Huawei modem, so let's look at the output. The relevant entry is: Bus 004 Device 004: ID 12d1:140b Huawei Technologies Co., Ltd Hence, you must type: sudo modprobe usbserial vendor=0x12d1 product=0x140b 2nd option Download usb-modeswitch and usb-modeswitch-data packages from packages.ubuntu.com. Install them through the command: sudo dpkg -i usb-modeswitch*.deb 3rd option Try a combination of both. but with no result. Modem still is not detected. I've tried to add new conection but system can't see my device in setup dialogue. Also i noticed that when i open eg. terminal and try to type sth, system freeze for a while.. Thx for help!

  Read the article

< Previous Page | 2 3 4 5 6 7 8 9 10 11  | Next Page >