Search Results

Search found 452 results on 19 pages for 'passive sts'.

Page 6/19 | < Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >

• Atheros Wireless card shows up as two different models?

  - by geermc4

  Hi I've been fighting these wireless drivers for a few days and just recently i noticed that the model the Wireless controller appears in lspci is different sometimes. This is the data i have after installing Ubuntu Server 64 bit ~# lspci -k .... 04:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: AzureWave Device 1d89 Kernel driver in use: ath9k Kernel modules: ath9k ran some updates, restarted, all was good, all though it did say that linux-headers-server linux-image-server linux-server where beeing kept back. After that i installed ubuntu-desktop (aptitude install ubuntu-desktop --without-recommends) restarted and not only is the wireless not working anymore, but the hardware is listed as a different card ~# lspci -k .... 04:00.0 Ethernet controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) has no available drivers for it, still i tried to modprobe ath9k, they show up in lsmod as loaded, but still iw list shows nothing. this is what it looked like before the ubuntu-desktop instalation Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (14.0 dBm) * 2417 MHz [2] (15.0 dBm) * 2422 MHz [3] (15.0 dBm) * 2427 MHz [4] (15.0 dBm) * 2432 MHz [5] (15.0 dBm) * 2437 MHz [6] (15.0 dBm) * 2442 MHz [7] (15.0 dBm) * 2447 MHz [8] (15.0 dBm) * 2452 MHz [9] (15.0 dBm) * 2457 MHz [10] (15.0 dBm) * 2462 MHz [11] (15.0 dBm) * 2467 MHz [12] (15.0 dBm) (passive scanning) * 2472 MHz [13] (14.0 dBm) (passive scanning) * 2484 MHz [14] (17.0 dBm) (passive scanning) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor interface combinations are not supported Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS. What's with the hardware change? If it has 2, how can i make the AR9285 always load and disable AR5008, or, is it the same and it's just showing it different? :| Oh and I've tried this on Ubuntu 10.04 server, xubuntu 12.04, ubuntu 12.04 desktop and server. Thanks in advanced. -- Here's some more info, i have it setup in 2 hard drives, 1 works and the other one i'm using to figure it out The one that works... # lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: 54:04:a6:a3:3b:96 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.2.147 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:43 ioport:e000(size=256) memory:d0004000-d0004fff memory:d0000000-d0003fff *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 01 serial: 74:2f:68:4a:26:73 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-18-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:fea00000-fea0ffff Here's where it doesn't # lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: 54:04:a6:a3:3b:96 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.2.160 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:43 ioport:e000(size=256) memory:d0004000-d0004fff memory:d0000000-d0003fff *-network UNCLAIMED description: Ethernet controller product: AR5008 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:fea00000-fea0ffff Update I've noticed that if i blacklist the ath9k and ath9k_common modules lspci gives me the AR9285, but then I need to modprobe ath9k for it to work, does this make any sense? If so, why?

  Read the article

• ActAs and OnBehalfOf support in WIF

  - by cibrax

  I discussed a time ago how WIF supported a new WS-Trust 1.4 element, “ActAs”, and how that element could be used for authentication delegation.  The thing is that there is another feature in WS-Trust 1.4 that also becomes handy for this kind of scenario, and I did not mention in that last post, “OnBehalfOf”. Shiung Yong wrote an excellent summary about the difference of these two new features in this forum thread. He basically commented the following, “An ActAs RST element indicates that the requestor wants a token that contains claims about two distinct entities: the requestor, and an external entity represented by the token in the ActAs element. An OnBehalfOf RST element indicates that the requestor wants a token that contains claims only about one entity: the external entity represented by the token in the OnBehalfOf element. In short, ActAs feature is typically used in scenarios that require composite delegation, where the final recipient of the issued token can inspect the entire delegation chain and see not just the client, but all intermediaries to perform access control, auditing and other related activities based on the whole identity delegation chain. The ActAs feature is commonly used in multi-tiered systems to authenticate and pass information about identities between the tiers without having to pass this information at the application/business logic layer. OnBehalfOf feature is used in scenarios where only the identity of the original client is important and is effectively the same as identity impersonation feature available in the Windows OS today. When the OnBehalfOf is used the final recipient of the issued token can only see claims about the original client, and the information about intermediaries is not preserved. One common pattern where OnBehalfOf feature is used is the proxy pattern where the client cannot access the STS directly but is instead communicating through a proxy gateway. The proxy gateway authenticates the caller and puts information about him into the OnBehalfOf element of the RST message that it then sends to the real STS for processing. The resulting token is going to contain only claims related to the client of the proxy, making the proxy completely transparent and not visible to the receiver of the issued token.” Going back to WIF, “ActAs” and “OnBehalfOf” are both supported as extensions methods in the WCF client channel. public static class ChannelFactoryOperations {   public static T CreateChannelActingAs<T>(this ChannelFactory<T> factory,     SecurityToken actAs);     public static T CreateChannelOnBehalfOf<T>(this ChannelFactory<T> factory,     SecurityToken onBehalfOf); } Both methods receive the security token with the identity of the original caller.

  Read the article

• Why doesn't pppd over ssh work here? Why can't I kill pppd?

  - by Peter V. Mørch

  I'm trying to setup a simple ppp tunnel over ssh. It works on several machines just fine. But on one machine, pppd gets "stuck": > pgrep pppd | xargs ps up USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 4178 0.0 0.1 3020 1088 pts/1 Ds+ 05:28 0:00 /usr/sbin/pppd Any attempt to kill it (even sudo kill -9 4178) has no effect that I can see. strace -p 4178 also hangs similarly. After it has been started for a while, I start getting messages in dmesg like shown below. It is started like so from another machine: ssh -t root@server /usr/sbin/pppd passive noauth When I do this to one of the machines that work, the remote end's pppd spits out garbage/binary data to the console (as expected). When I do it to the one that fails, I get no output from pppd, but the ssh session eventually times out. If I instead ssh to the machine, and then run /usr/sbin/pppd passive noauth in a separate step I also get the expected binary output. I now have a couple of questions: What could be up with the one machine where pppd fails? I don't even know where to start looking... What could be the difference between ssh -t root@server /usr/sbin/pppd passive noauth in a single step and ssh root@server and /usr/sbin/pppd passive noauth in two steps? How can it be that I can't kill the process even with sudo kill -9? The only way I know is to reboot. (I've tried searching for something similar but didn't get anywhere so I'm sorry I don't have any more leads) Any ideas? The problem machine runs in debian on VMware "hardware" (as do the ones that work) and it exhibits the problem when cloned and on both debian lenny (original) and squeeze (after upgrade) dmesg entries: [ 1198.727248] INFO: task pppd:4178 blocked for more than 120 seconds. [ 1198.727507] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1198.727904] pppd D ece2dc9c 0 4178 4174 0x00000004 [ 1198.727908] 00000098 00000082 f2503520 ece2dc9c 0000b1e7 00000000 c148d1c0 c148d1c0 [ 1198.727913] f2a06100 f6e071c0 00000000 ece2dc18 f5cd07e0 00000000 ece2d400 ece2dc9d [ 1198.727918] 00c52300 ece2dcbc f67bfef8 ec98e480 f291cec0 00000000 c10cf5b0 c10dfd21 [ 1198.727923] Call Trace: [ 1198.727926] [<c10cf5b0>] ? nameidata_to_filp+0x37/0x41 [ 1198.727929] [<c10dfd21>] ? dput+0x21/0xb7 [ 1198.727932] [<c11cfecc>] ? tty_ldisc_ref_wait+0x5f/0x76 [ 1198.727935] [<c104de7a>] ? wake_up_bit+0x5c/0x5c [ 1198.727938] [<c11cb91b>] ? tty_ioctl+0x85f/0x8ba [ 1198.727941] [<c10fec18>] ? do_lock_file_wait+0x3d/0xd9 [ 1198.727944] [<c1162c97>] ? _copy_from_user+0x2b/0x102 [ 1198.727946] [<c11cb0bc>] ? tty_check_change+0xb9/0xb9 [ 1198.727949] [<c10dbeb7>] ? do_vfs_ioctl+0x485/0x4c7 [ 1198.727952] [<c10db59a>] ? do_fcntl+0x24f/0x3a2 [ 1198.727954] [<c10dbf3a>] ? sys_ioctl+0x41/0x58 [ 1198.727957] [<c12c6a1f>] ? sysenter_do_call+0x12/0x28 [ 1318.457225] INFO: task sshd:4174 blocked for more than 120 seconds. [ 1318.457500] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1318.457896] sshd D f25024cc 0 4174 2393 0x00000000 [ 1318.457901] 00000098 00000086 f2a06940 f25024cc 0000b246 00000000 c148d1c0 c148d1c0 [ 1318.457906] f2503520 f6e071c0 00000000 3f056585 0000000f ece2d4bc 3f056585 f2503520 [ 1318.457911] ec98bb38 ec98bbdc 00000000 00000000 00000000 c12c09b5 f2503520 c10327cb [ 1318.457916] Call Trace: [ 1318.457926] [<c12c09b5>] ? schedule_hrtimeout_range_clock+0x3c/0xd9 [ 1318.457931] [<c10327cb>] ? try_to_wake_up+0x13f/0x13f [ 1318.457935] [<c11cfecc>] ? tty_ldisc_ref_wait+0x5f/0x76 [ 1318.457940] [<c104de7a>] ? wake_up_bit+0x5c/0x5c [ 1318.457943] [<c11c9ad3>] ? tty_poll+0x32/0x5e [ 1318.457947] [<c10dd4d5>] ? do_select+0x2a1/0x42e [ 1318.457950] [<c10dcb83>] ? poll_freewait+0x69/0x69 [ 1318.457953] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457955] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457958] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457960] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457963] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457965] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457968] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457971] [<c10429c2>] ? lock_timer_base+0x19/0x35 [ 1318.457974] [<c1042eb5>] ? __mod_timer+0x10c/0x116 [ 1318.457977] [<c1042f89>] ? mod_timer+0x69/0x6e [ 1318.457981] [<c121325d>] ? sk_reset_timer+0xc/0x16 [ 1318.457984] [<c1252f57>] ? tcp_event_new_data_sent+0x66/0x6b [ 1318.457987] [<c1255b85>] ? tcp_write_xmit+0x7a7/0x86a [ 1318.457990] [<c121760d>] ? __alloc_skb+0x50/0xfd [ 1318.457994] [<c12c12bc>] ? _raw_spin_lock_bh+0x8/0x1e [ 1318.457996] [<c1212e98>] ? release_sock+0x10/0xc4 [ 1318.457999] [<c124b543>] ? tcp_sendmsg+0x6dd/0x7b7 [ 1318.458003] [<c1162c97>] ? _copy_from_user+0x2b/0x102 [ 1318.458006] [<c10dd7a0>] ? core_sys_select+0x13e/0x1c3 [ 1318.458009] [<c12102a3>] ? sock_aio_write+0xc0/0xd4 [ 1318.458012] [<c10d0655>] ? do_sync_write+0xa0/0xe4 [ 1318.458016] [<c10b141c>] ? handle_mm_fault+0x222/0x238 [ 1318.458019] [<c10f6096>] ? fsnotify+0x1de/0x1f9 [ 1318.458022] [<c10dd9e8>] ? sys_select+0x6e/0x8f [ 1318.458024] [<c10d105e>] ? sys_write+0x3c/0x63 [ 1318.458028] [<c12c6a1f>] ? sysenter_do_call+0x12/0x28

  Read the article

• ProFTPd server on Ubuntu getting access denied message when successfully authenticated?

  - by exxoid

  I have a Ubuntu box with a ProFTPD 1.3.4a Server, when I try to log in via my FTP Client I cannot do anything as it does not allow me to list directories; I have tried logging in as root and as a regular user and tried accessing different paths within the FTP Server. The error I get in my FTP Client is: Status: Retrieving directory listing... Command: CDUP Response: 250 CDUP command successful Command: PWD Response: 257 "/var" is the current directory Command: PASV Response: 227 Entering Passive Mode (172,16,4,22,237,205). Command: MLSD Response: 550 Access is denied. Error: Failed to retrieve directory listing Any idea? Here is the config of my proftpd: # # /etc/proftpd/proftpd.conf -- This is a basic ProFTPD configuration file. # To really apply changes, reload proftpd after modifications, if # it runs in daemon mode. It is not required in inetd/xinetd mode. # # Includes DSO modules Include /etc/proftpd/modules.conf # Set off to disable IPv6 support which is annoying on IPv4 only boxes. UseIPv6 off # If set on you can experience a longer connection delay in many cases. IdentLookups off ServerName "Drupal Intranet" ServerType standalone ServerIdent on "FTP Server ready" DeferWelcome on # Set the user and group that the server runs as User nobody Group nogroup MultilineRFC2228 on DefaultServer on ShowSymlinks on TimeoutNoTransfer 600 TimeoutStalled 600 TimeoutIdle 1200 DisplayLogin welcome.msg DisplayChdir .message true ListOptions "-l" DenyFilter \*.*/ # Use this to jail all users in their homes # DefaultRoot ~ # Users require a valid shell listed in /etc/shells to login. # Use this directive to release that constrain. # RequireValidShell off # Port 21 is the standard FTP port. Port 21 # In some cases you have to specify passive ports range to by-pass # firewall limitations. Ephemeral ports can be used for that, but # feel free to use a more narrow range. # PassivePorts 49152 65534 # If your host was NATted, this option is useful in order to # allow passive tranfers to work. You have to use your public # address and opening the passive ports used on your firewall as well. # MasqueradeAddress 1.2.3.4 # This is useful for masquerading address with dynamic IPs: # refresh any configured MasqueradeAddress directives every 8 hours <IfModule mod_dynmasq.c> # DynMasqRefresh 28800 </IfModule> # To prevent DoS attacks, set the maximum number of child processes # to 30. If you need to allow more than 30 concurrent connections # at once, simply increase this value. Note that this ONLY works # in standalone mode, in inetd mode you should use an inetd server # that allows you to limit maximum number of processes per service # (such as xinetd) MaxInstances 30 # Set the user and group that the server normally runs at. # Umask 022 is a good standard umask to prevent new files and dirs # (second parm) from being group and world writable. Umask 022 022 # Normally, we want files to be overwriteable. AllowOverwrite on # Uncomment this if you are using NIS or LDAP via NSS to retrieve passwords: # PersistentPasswd off # This is required to use both PAM-based authentication and local passwords AuthPAMConfig proftpd AuthOrder mod_auth_pam.c* mod_auth_unix.c # Be warned: use of this directive impacts CPU average load! # Uncomment this if you like to see progress and transfer rate with ftpwho # in downloads. That is not needed for uploads rates. # UseSendFile off TransferLog /var/log/proftpd/xferlog SystemLog /var/log/proftpd/proftpd.log # Logging onto /var/log/lastlog is enabled but set to off by default #UseLastlog on # In order to keep log file dates consistent after chroot, use timezone info # from /etc/localtime. If this is not set, and proftpd is configured to # chroot (e.g. DefaultRoot or <Anonymous>), it will use the non-daylight # savings timezone regardless of whether DST is in effect. #SetEnv TZ :/etc/localtime <IfModule mod_quotatab.c> QuotaEngine off </IfModule> <IfModule mod_ratio.c> Ratios off </IfModule> # Delay engine reduces impact of the so-called Timing Attack described in # http://www.securityfocus.com/bid/11430/discuss # It is on by default. <IfModule mod_delay.c> DelayEngine on </IfModule> <IfModule mod_ctrls.c> ControlsEngine off ControlsMaxClients 2 ControlsLog /var/log/proftpd/controls.log ControlsInterval 5 ControlsSocket /var/run/proftpd/proftpd.sock </IfModule> <IfModule mod_ctrls_admin.c> AdminControlsEngine off </IfModule> # # Alternative authentication frameworks # #Include /etc/proftpd/ldap.conf #Include /etc/proftpd/sql.conf # # This is used for FTPS connections # #Include /etc/proftpd/tls.conf # # Useful to keep VirtualHost/VirtualRoot directives separated # #Include /etc/proftpd/virtuals.con # A basic anonymous configuration, no upload directories. # <Anonymous ~ftp> # User ftp # Group nogroup # # We want clients to be able to login with "anonymous" as well as "ftp" # UserAlias anonymous ftp # # Cosmetic changes, all files belongs to ftp user # DirFakeUser on ftp # DirFakeGroup on ftp # # RequireValidShell off # # # Limit the maximum number of anonymous logins # MaxClients 10 # # # We want 'welcome.msg' displayed at login, and '.message' displayed # # in each newly chdired directory. # DisplayLogin welcome.msg # DisplayChdir .message # # # Limit WRITE everywhere in the anonymous chroot # <Directory *> # <Limit WRITE> # DenyAll # </Limit> # </Directory> # # # Uncomment this if you're brave. # # <Directory incoming> # # # Umask 022 is a good standard umask to prevent new files and dirs # # # (second parm) from being group and world writable. # # Umask 022 022 # # <Limit READ WRITE> # # DenyAll # # </Limit> # # <Limit STOR> # # AllowAll # # </Limit> # # </Directory> # # </Anonymous> # Include other custom configuration files Include /etc/proftpd/conf.d/ UseReverseDNS off <Global> RootLogin on UseFtpUsers on ServerIdent on DefaultChdir /var/www DeleteAbortedStores on LoginPasswordPrompt on AccessGrantMsg "You have been authenticated successfully." </Global> Any idea what could be wrong? Thanks for your help!

  Read the article

• rails db migration, undefined method `to_sym', cant figure out syntax

  - by oelbrenner

  the original migration looks like this: class CreateUsers true do |t| t.string :login, :limit = 40 t.string :name, :limit = 100, :default = '', :null = true t.string :email, :limit = 100 t.string :crypted_password, :limit = 40 t.string :salt, :limit = 40 t.string :remember_token, :limit = 40 t.datetime :remember_token_expires_at t.string :activation_code, :limit = 40 t.datetime :activated_at, :datetime t.string :state, :null = :no, :default = 'passive' t.datetime :deleted_at t.integer :occupation_id, :null = :yes t.datetime :paid_up_to_date, :date t.timestamps end and I am trying to change the default of "state" to be "active" instead of passive so my attempt at a migration looks like this: ( still learning.. be gentle ) class ChangeUserStateDefault < ActiveRecord::Migration def self.up change_column :users, :state, :null = :no, :default = 'active' end def self.down end end

  Read the article

• proftpd, dynamic IP, and filezilla: port troubles

  - by Yami

  The basic setup: Two computers, one running proftpd, one attempting to connect via filezilla. Both linux (xubuntu on the server, kubuntu on the client). Both are at the moment behind a router on a residential (read: dynamic IP) connection; the client is a laptop I plan to take away from the home network, so I'll need this to work externally. I have my router set up to allow specific ports forwarded to each machine and, where possible, have plugged in those numbers into proftpd (via gadmin, double-checking the config file) and filezilla. Attempting to connect via active mode using the internal IP works: Status: Connecting to 192.168.1.139:8085... Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER <redacted> Response: 331 Password required for <redacted> Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PORT 192,168,1,52,153,140 Response: 200 PORT command successful Command: LIST Response: 150 Opening ASCII mode data connection for file list Response: 226 Transfer complete Status: Directory listing successful Attempting to connect via the domain name, however, leads to issues; in active mode, the PORT is the last command to be received according to the server's logs, and in passive mode, it's the PASV command. This leads me to believe I'm being redirected to a bad port? Active Sample: Status: Resolving address of <url> Status: Connecting to <ip:port> Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER <redacted> Response: 331 Password required for <redacted> Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PORT 174,111,127,27,153,139 Response: 200 PORT command successful Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing Passive sample: Status: Resolving address of ftp.bonsaiwebdesigns.com Status: Connecting to 174.111.127.27:8085... Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER yamikuronue Response: 331 Password required for yamikuronue Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PASV Response: 227 Entering Passive Mode (64,95,64,197,101,88). Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing In both cases, the log file ends at "PORT" or "PASV" - there's no record of ever receiving a "LIST" command. Just above that I can see the attempt to connect actively via the internal IP, which does indeed include a LIST command. My config file includes "PassivePorts 20001-26999", which are the port forwards I set up for the ftp server, and "Port 8085", which is also forwarded to the same machine. I also have a MasqueradeAddress set up to prevent it from reporting its internal IP, which was an earlier issue I had. I think what I'm asking is, is there another setting someplace I have to change to get this setup to work?

  Read the article

• Jquery Session & Table Filtering

  - by Bry4n

  This is my Jquery <script type="text/javascript"> $(function() { var from = $.session("from"); var to = $.session("to"); var $th = $('#theTable').find('th'); // had to add the classes here to not grab the "td" inside those tables var $td = $('#theTable').find('td.bluedata,td.yellowdata'); $th.hide(); $td.hide(); if (to == "Select" || from == "Select") { // shortcut - nothing set, show everything $th.add($td).show(); return; } var filterArray = new Array(); filterArray[0] = to; filterArray[1] = from; $.each(filterArray, function(i){ if (filterArray[i].toString() == "Select") { filterArray[i] = ""; } }); $($th).each(function(){ if ($( this,":eq(0):contains('" + filterArray[0].toString() + "')") != null && $(this,":eq(1):contains('" + filterArray[1].toString() + "')") != null) { $(this).show(); } }); $($td).each(function(){ if ($( this,":eq(0):contains('" + filterArray[0].toString() + "')") != null && $(this,":eq(1):contains('" + filterArray[1].toString() + "')") != null) { $(this).show(); } }); }); </script> This is my table <table border="1" id="theTable"> <tr class="headers"> <th class="bluedata"height="20px" valign="top">63rd St. &amp; Malvern Av. Loop<BR/></th> <th class="yellowdata"height="20px" valign="top">52nd St. &amp; Lansdowne Av.<BR/></th> <th class="bluedata"height="20px" valign="top">Lancaster &amp; Girard Avs<BR/></th> <th class="yellowdata"height="20px" valign="top">40th St. &amp; Lancaster Av.<BR/></th> <th class="bluedata"height="20px" valign="top">36th &amp; Market Sts<BR/></th> <th class="bluedata"height="20px" valign="top">6th &amp; Market Sts<BR/></th> <th class="yellowdata"height="20px" valign="top">Juniper Station<BR/></th> </tr> <tr> <td class="bluedata"height="20px" title="63rd St. &amp; Malvern Av. Loop"> <table width="100%"><tr><td>12:17am</td></tr><tr><td>12:17am</td></tr><tr><td>12:47am</td></tr></table> </td> <td class="yellowdata"height="20px" title="52nd St. &amp; Lansdowne Av."> <table width="100%"><tr><td>12:17am</td></tr><tr><td>12:17am</td></tr><tr><td>12:47am</td></tr></table> </td> <td class="bluedata"height="20px" title="Lancaster &amp; Girard Avs"> <table width="100%"><tr><td>12:17am</td></tr><tr><td>12:17am</td></tr><tr><td>12:47am</td></tr></table> </td> <td class="yellowdata"height="20px" title="40th St. &amp; Lancaster Av."> <table width="100%"><tr><td>12:17am</td></tr><tr><td>12:17am</td></tr><tr><td>12:47am</td></tr></table> </td> <td class="bluedata"height="20px" title="36th &amp; Market Sts"> <table width="100%"><tr><td>12:17am</td></tr><tr><td>12:17am</td></tr><tr><td>12:47am</td></tr></table> </td> <td class="bluedata"height="20px" title="6th &amp; Market Sts"> <table width="100%"><tr><td>12:17am</td></tr><tr><td>12:17am</td></tr><tr><td>12:47am</td></tr></table> </td> <td class="bluedata"height="20px" title="Juniper Station"> <table width="100%"><tr><td>12:17am</td></tr><tr><td>12:17am</td></tr><tr><td>12:47am</td></tr></table> </td> </tr> </table> I have asked questions on here before and I have had success in converting textbox values to dropdown changes. However this is a bit different. I am using the sessions plugin (which works fine). On one page I have a set of normal drop downs, on submit you get taken to a separate page which runs the function above, however the rows/columns all show and they don't seem to filter at all.

  Read the article

• Failure retrieving contents of directory

  - by Bondye

  Currently I have a couple of websites. My problem is that if I login on 1 specific domain with any of my programs (using notepadd++, FileZilla and Netbeans) the program stops at the content listing. I had it correctly running, (I'm working on a project on this domain for more than a year now) and suddenly I broke it somehow. This only happens on 1 specific domain, all other domains (from other hosts) are working. My colleague (next to me with same ip address) is able to login on this domain. Notepadd++ says: Failure retrieving contents of directory Filezilla says: Failed to retrieve directory listing Netbean popups: Upload files on save failed. (Because I have the setting upload on save enabled.) What I tried: First I thought it's my firewall, I disabled firewall but no result. Also notice that all other domain are working. Maby a blacklist with my ip address? No my colleague has the same ip address. Could anyone help me on this? Notepad++ Log [NppFTP] Everything initialized -> TYPE I Connecting -> Quit 220 ProFTPD 1.3.3e Server ready. -> USER username 331 Password required for domain -> PASS *HIDDEN* 230 User username logged in -> TYPE A 200 Type set to A -> MODE S 200 Mode set to S -> STRU F 200 Structure set to F -> CWD /domains/domain.nl/ 250 CWD command successful Connected -> CWD /domains/domain.nl/ 250 CWD command successful -> PASV 227 Entering Passive Mode (194,247,31,xx,137,xx). -> LIST -al Failure retrieving contents of directory /domains/domain.nl/ Filezilla log Status: Verbinden met 194.247.xx.xx:21... Status: Verbinding aangemaakt, welkomstbericht afwachten... Antwoord: 220 ProFTPD 1.3.3e Server ready. Commando: USER username Antwoord: 331 Password required for username Commando: PASS ******** Antwoord: 230 User username logged in Commando: SYST Antwoord: 215 UNIX Type: L8 Commando: FEAT Antwoord: 211-Features: Antwoord: MDTM Antwoord: MFMT Antwoord: LANG en-US;ja-JP;zh-TW;it-IT;fr-FR;zh-CN;ru-RU;bg-BG;ko-KR Antwoord: TVFS Antwoord: UTF8 Antwoord: AUTH TLS Antwoord: MFF modify;UNIX.group;UNIX.mode; Antwoord: MLST modify*;perm*;size*;type*;unique*;UNIX.group*;UNIX.mode*;UNIX.owner*; Antwoord: PBSZ Antwoord: PROT Antwoord: REST STREAM Antwoord: SIZE Antwoord: 211 End Commando: OPTS UTF8 ON Antwoord: 200 UTF8 set to on Status: Verbonden Status: Mappenlijst ophalen... Commando: PWD Antwoord: 257 "/" is the current directory Commando: TYPE I Antwoord: 200 Type set to I Commando: PASV Antwoord: 227 Entering Passive Mode (194,247,31,xx,xxx,xx). Commando: MLSD Fout: Verbinding verloren Fout: Ontvangen van mappenlijst is mislukt Sorry that it's dutch.

  Read the article

• DRBD and MySQL - Heartbeat Setup

  Heartbeat automates all the moving parts and can work as well with the MySQL master-master active/passive solution as well as it can with the MySQL & DRBD solution. It manages the virtual IP address used by the database, directs DRBD to become primary, or relinquish primary duties, mounts the /dev/drbd0 device, and starts/stops MySQL as needed.

  Read the article

• DRBD and MySQL - Heartbeat Setup

  Heartbeat automates all the moving parts and can work as well with the MySQL master-master active/passive solution as well as it can with the MySQL & DRBD solution. It manages the virtual IP address used by the database, directs DRBD to become primary, or relinquish primary duties, mounts the /dev/drbd0 device, and starts/stops MySQL as needed.

  Read the article

• Opinion: Whatever the iPad is, it is NOT a Computer

  Emery Fletcher doesn't think much of all the overwrought iPad hype, nor the device itself, saying it is not a real computer, but a PAD-- "Passive Amusement Device."

  Read the article

• Nagios: Central Monitoring

  <b>Begin Linux:</b> "This is part two of a three part series on distributed monitoring. You can usehttp://newsadmin.linuxtoday.com/ passive service and host checks to allow non-central Nagios servers to collect data from a network of machines and then transfer that information to a central Nagios server."

  Read the article

• Editor's Note: All This Great Technology Just to Reinvent Television

  The cloud, the smartphone, the tablet, the Web itself as a big giant operating system-- what's the fatal flaw in all of these? It's all about feeding content to passive "consumers". Plug me in, baby, I'm not lifting a finger ever again.

  Read the article

• Random thoughts on Monday

  - by user10760339

  I know that it has been a long time since my last post, just though that I would update you my latest thoughts of Governance. I just recently completed an executive round table series on EA and Cloud in Singapore, Indonesia and Malaysia. The response was phenomenal. The key point of the session was that Enterprise is the key enabler of innovation - All companies want to drive to be market leaders, EA can lay the foundation for the path to deliver that at innovation. When it comes to innovation, I see two distinct types: (a) Passive innovation is where a company creates innovation thought increments improvement over time. A great example is when airlines went from paper tickets to electronic ticket. Next logical progression is to do the same with boarding passes. There are a lot of examples to choose from, thought the thing to keep in mind, is that passive innovation will only keep you in the lead, it won’t allow you to create new markets or jump from #3 to #1 in one go. For that we need another type of innovation. (b) Disruptive innovation is where you create market where none existed before. Thought very difficult to do and requires significant investment in research, product and software development and not least of all, visionary thinking and timing, if done correctly, can turn the world on it’s ear. A great example is Apple iTunes. Some might say that this is incremental innovation, but only in one aspect, the downloading of music. Other then that, it’s all disruptive innovation. Being able to buy a single song rather then the album fundamentally changed the way we get out music. Behind all of these types of innovation is Enterprise Architecture. EA creates the infrastructure foundation, then delivery systems and the end-user experience to deliver this innovation. At Oracle, we are driving that EA innovation with our private cloud offerings from “bolt-to-glass” as I like to say. For more on what Oracle has to offer in EA and cloud, have a look at Cloud Computing | Oracle and Enterprise Architecture - OracleI am working on new material that I will be posting in a couple of weeks, so check back regularly for new updates or feel free to subscript for updates.

  Read the article

• What is the status in 3D technology for TVs [closed]

  - by Eduardo Molteni

  Maybe it is off-topic for programmers.SE, but don't know where else to ask, and I trust my fellow programmers :) I've recently being lightly following new 3D technologies and I thought that glass-free 3D TV was about to take over the scene since it make much more sense to TVs (I can't imagine having glasses for all the family, kids breaking them, etc) But it seems that I'm wrong, since LG, Sony and Samsumg keep fighting over glasses (active-passive) What is the current and future status in 3D technology for TVs?

  Read the article

• Forcing Zeitgeist to index Dropbox folder

  - by Jarmo

  I am running Ubuntu 11.10, and I would like to force Zeitgeist to index my Dropbox folder. I understand that Zeitgeist is a passive service that logs particular events (such as opening or downloading files) for later searches, but I have large Dropbox folder that was downloaded without being logged by Zeitgeist. Short of manually opening and closing all files in my Dropbox folder, is there a way to have Zeitgeist index this folder so that I can later search it using the dash? Thanks!

  Read the article

• Installing and Managing Multi Master Replication Manager (MMM) for MySQL High Ava

  <b>PACKT Publishing: </b>"Multi Master Replication Manager for MySQL ("MMM") is a set of open source Perl scripts designed to automate the process of creating and automatically managing the "Active / Passive Master" high availability replication."

  Read the article

• As an Indie iOS Developer, is it more profitable to market apps heavily or focus on publishing more apps? [closed]

  - by user69860

  At first I thought that if I made a bunch of $0.99 apps that were all pretty nice that they would eventually start to make me some decent passive income. However, after publishing five $0.99 applications in the the Apple App Store, I'm finding that I make around $5/day, which is basically nothing. Should I invest time into creating an even better app, hire a designer, spend money on PR and marketing, and then keep spending time updating/managing that app? Or should I continue to produce more applications solo?

  Read the article

• How to Build Your Own Empire of Websites

  How would you like to create a massive empire of websites that all bring in passive residual income? It is possible to build a flurry of websites and use them to create more than a full-time income working from home.

  Read the article

• squid and ftp connections

  - by Kstro21

  i have a squid proxy server for both, http and ftp connections, i'm trying to use filezilla to open a ftp, but it always fail with an error saying: Status: Connection with proxy established, performing handshake... Response: Proxy reply: HTTP/1.0 403 Forbidden Error: Proxy handshake failed: ECONNRESET - Connection reset by peer Error: Connection timed out Error: Failed to retrieve directory listing i sniff the traffic, and, filezilla is trying to connect to a different port and the proxy denied it look, this is a portion of the sniff result CONNECT 201.150.36.227:61179 HTTP/1.1 Host: 201.150.36.227:61179 User-Agent: FileZilla everytime is a different port, so, no way i can allow it in the squid, also, i set the filezilla to use a active connection, same result, passive connection, same result again, so, i'm out of bullets, and i need your help, maybe a setting in the filezilla or in the squid can do the job, so, give a hand here this is the full log of the filezilla Status: Connecting to uhma.mx through proxy Status: Connecting to 172.19.216.13:3128... Status: Connection with proxy established, performing handshake... Response: Proxy reply: HTTP/1.0 200 Connection established Status: Connection established, waiting for welcome message... Response: 220 ProFTPD 1.3.3a Server (a3 FTP CUATRO) [201.150.36.227] Command: USER uhmamx Response: 331 Password required for uhmamx Command: PASS ******* Response: 230 User uhmamx logged in Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PASV Response: 227 Entering Passive Mode (201,150,36,227,238,251). Command: MLSD Status: Connecting to 172.19.216.13:3128... Status: Connection with proxy established, performing handshake... Response: Proxy reply: HTTP/1.0 403 Forbidden Error: Proxy handshake failed: ECONNRESET - Connection reset by peer Error: Connection timed out Error: Failed to retrieve directory listing

  Read the article

• SFTP only works occasionally

  - by 82din

  I suddenly get this error using SFTP: Status: Connecting to example.com... Response: fzSftp started Command: open "[email protected]" 22 Command: Pass: ********* Status: Connected to example.com Status: Retrieving directory listing... Command: pwd Response: Current directory is: "/root" Command: ls Status: Listing directory /root Error: Connection timed out Error: Failed to retrieve directory listing I tried using FileZila, Cyberduck, Shell (Terminal), same result. However, it worked fine today (just a few seconds) in Passive mode. I guess something changed in my network, so I have tried both: Active and Passive mode: Connecting to probe.filezilla-project.org Response: 220 FZ router and firewall tester ready USER FileZilla Response: 331 Give any password. PASS 3.6.0.2 Response: 230 logged on. Checking for correct external IP address Retrieving external IP address from http://checkip.dyndns.org:8245/ Checking for correct external IP address IP <external IP> big-bf-ccc-f Response: 200 OK PREP 49565 Response: 200 Using port 49565, data token 380352881 PORT 186,15,222,5,193,157 Response: 200 PORT command successful LIST Response: 150 opening data connection Response: 503 Failure of data connection. Server sent unexpected reply. Connection closed Because I'm working behind a router, I get my external IP from http://checkip.dyndns.org:8245/ I also tested different range of ports.

  Read the article

• Best practice for Exchange 2010 HA topology considering 6 x Exchange licenses and TMG 2010

  - by MadBoy

  What would be best topology considering that: 6 x Exchange 2010 Standard Licenses 2 x Separate locations that are supposed to support redundancy in case of link problems 4 x Forefront TMG 2010 with Forefront Security and Forefront Protection/Security Multiple locations worldwide using those Exchange. Most locations will be connected with VPN Tunnel (the ones hosting Exchange for sure). I was thinking something like this: Location MAIN (about 70-100 people): 2x TMG 2010 in NLB 1x Exchange 2010 CAS/HUB Role 2x Exchange 2010 Mailbox Role (Active + Passive) Location SUPPORT (about 20 people): 2x TMG 2010 in NLB 1x Exchange 2010 CAS/HUB Role 2x Exchange 2010 Mailbox Role (Active + Passive) Management wants to make sure that in case of problems in main location (power failure, link loss etc) second location can support all traffic from around the world and vice-versa. We have 6-7 locations and more comming up (not big ones but like 10+ people per each location). I do know that CAS/HUB is single point of failure (and no NLB), but i simply lack more licenses to do some redundancy on that. What do you think about this approach? What would be better approach according to you?

  Read the article

• Cisco router not receiving OSPF updates

  - by WebDevHobo

  Or at least, that's what I think is happening. There doesn't appear to be a debug command for this, or to see if something is in the routing table. I'm testing out this setup in Packet Tracer. I have 3 routers and a webserver From left to right, you have: Webserver - Router1 - Router2 - Router3 Router1 and Router2 can succesfully ping WebServer. Router3 cannot. Router2 has a default gateway set, to send all not-recognized data through its serial interface to Router1. Like this: ip route 0.0.0.0 0.0.0.0 Serial 0/0/1 Serial 0/0/1 being the connection to Router1 Router2 and Router3 have OSPF configured. From their "show run": Router2: router ospf 1 log-adjacency-changes passive-interface Serial0/0/1 network 10.1.1.0 0.0.0.3 area 0 default-information originate ! Router3: router ospf 1 log-adjacency-changes network 10.1.1.0 0.0.0.3 area 0 passive-interface FastEthernet0/0 ! I was under the assumption that setting default-information originate on Router2 would give Router3 the needed information. What's going wrong here? The interfaces are up. Ip addresses are with mask-range, clock rate is set at correct end. I don't know what else to check.

  Read the article

• Launching Installer Via Powershell and WinRM and Nothing Happens

  - by Nick DeMayo

  I'm currently working on a Powershell script to run some Microsoft Hotfix installers remotely on several Windows Server 2008 R2 servers that I manage. Basically, the script copies all the appropriate files up to the server, and then runs the installer via Invoke-Command, like so: function InstallCU { Write-Host "Installing June 2013 CU..." Invoke-Command -ComputerName $ServerName -ScriptBlock { Start-Process "c:\aaa\prjcusp2\ubersrvprj2010-kb2817530-fullfile-x64-glb.exe" -ArgumentList "/passive" } } If I run the "Start-Process" command locally on the server, the installer runs properly. However, when trying to run it remotely, nothing happens (actually, I can see the installer start up in Task Manager, but it closes a couple seconds later and doesn't run). I've attempted giving the Invoke-Command -Credentials, I've turned off UAC on the server, and I've ensured that my WinRM settings (running 'winrm quickconfig' and setting TrustedHosts to *) are correct. I've also tried having the Invoke-Command script run a local Powershell script to run the installer and changing the Argument from '/passive' to 'quiet' (in case it can't remotely launch something that has a UI), but again, no dice. Is there anything else I can try, or am I just not going to be able to do this?

  Read the article

• unable to destroy windows 2008 r2 failover cluster after SAN rebuild

  - by Zack

  I created a windows 2008 r2 failover cluster for a sql 2008 active/passive cluster. This two node cluster was using a SAN device for a quorum disk resource as well as MSDTC resource. Well....I decided to reconfigure the SAN device, but I didn't destroy the cluster first. Now that the quorum disk and mstdc disk are completely gone, the cluster is obviously not working. But, I can't even destroy the cluster and start again. I've tried from the Windows Clustering tool, as well as the command line. I was able to get the cluster service to start using the "/fixquorum" parameter. After doing this I was able to remove the passive node from the cluster, but it wouldn't let me destroy the cluster because the default resource group and msdtc are still attached as resources. I tried to delete these resources from both the GUI tool, as well as command line. It will either freeze for several minutes and crash the program, or once it even BSOD'd the server. Can someone advise on how to destroy this cluster so I can start over?

  Read the article

< Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >