Search Results

Search found 2401 results on 97 pages for 'routing'.

Page 6/97 | < Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >

  • Problem routing between directly connected Subnets w/ ASA-5510

    - by Zephyr Pellerin
    This is an issue I've been struggling with for quite some time, with a seemingly simple answer (Aren't all IT problems?). And that is the problem of passing traffic between two directly connected subnets with an ASA While I'm aware that best practice is to have Internet - Firewall - Router, in many cases this isn't possible. For example, In have an ASA with two interfaces, named OutsideNetwork (10.19.200.3/24) and InternalNetwork (10.19.4.254/24). You'd expect Outside to be able to get to, say, 10.19.4.1, or at LEAST 10.19.4.254, but pinging the interface gives only bad news. Result of the command: "ping OutsideNetwork 10.19.4.254" Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.19.4.254, timeout is 2 seconds: ????? Success rate is 0 percent (0/5) Naturally, you'd assume that you could add a static route, to no avail. [ERROR] route Outsidenetwork 10.19.4.0 255.255.255.0 10.19.4.254 1 Cannot add route, connected route exists At this point, you might gander if its a NAT or Access list problem. access-list Outsidenetwork_access_in extended permit ip any any access-list Internalnetwork_access_in extended permit ip any any There is no dynamic nat (or static nat for that matter), and Unnatted traffic is permitted. When I try pinging the above address (10.19.4.254 from Outsidenetwork), I get this error message from level 0 logging (debugging). Routing failed to locate next hop for icmp from NP Identity Ifc:10.19.200.3/0 to Outsidenetwork:10.19.4.1/0 This led me to set same-security traffic permit, and assigned the same, lesser and greater security numbers between the two interfaces. Am I overlooking something obvious? Is there a command to set static routes that are classified higher than connected routes?

    Read the article

  • Help with routing table

    - by user68752
    I have tried to find the answer to my question but not really found a clean and easy solution. I have a box (Ubuntu headless 10.04.1 server, with one Ethernet port) on LAN behind a router (running m0n0wall), that I have successfully installed a PPTP device (ppp0) on, this is working flawlessly (following this link) The thing is I want this box to route all it's internet traffic through the VPN tunnel (ppp0 device) but also being able to access the local LAN on 192.168.1.* subnet. I've succeeded a bit with this, but my problem right now is that I have port forwards (e.g. SSH) done in the m0n0wall pointing to this specific box which forces me to do "add routes" to all boxes that want to access this machine through this specific port. For instance a machine with ip xyz.xyz.xyz.xyz needs to have a static route setup in the routing table on the box to be able to access the box. This is the result of route -n xxx.xxx.137.2 192.168.1.1 255.255.255.255 UGH 0 0 0 eth0 xxx.xxx.137.2 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 yyy.yyy.0.0 192.168.1.1 255.255.0.0 UG 0 0 0 eth0 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 Where xxx is the IPs provided from VPN server. yyy.yyy.0.0 is a net that i want to have access to the box, without this I can't access the box from outside the LAN (via port-forwards done in router software, m0n0wall) is there away round this ugly solution?

    Read the article

  • Different subnets routing with just one layer 3 switch

    - by GustavoFSx
    Our current network looks like this: Location 1: 2 Layer 2 switches | subnet 192.168.1.0/24 | Firewall for our VPN Location 2: 1 Layer 2 switch | subnet 192.168.3.0/24 | Firewall for our VPN Location 3: 1 Layer 2 switch | subnet 192.168.5.0/24 | Firewall for our VPN We just got a direct fiber connection between location 1 and 2, we also got a new HP V1910 24G layer 3 switch. I tried to follow the instructions on this site, but I can't get it to work. I think our network should look like this: Location 1: HP Switch FIBER to L2 | subnet 192.168.1.0/24 | Firewall for our VPN Location 2: 1 Layer 2 switch | subnet 192.168.3.0/24 | FIBER to L1 Location 3: 1 Layer 2 switch | subnet 192.168.5.0/24 | Firewall for our VPN So, how can I get routing working on our location 2? It's old gateway was a firewall device on ip 192.168.3.1. I'm thinking on creating a VLAN Interface on 192.168.3.1 on the switch for the Location 2. But how will I handle that on the HP switch that has a direct fiber connection with that switch? Please help, I'm not very good with networking.

    Read the article

  • Mikrotik and NAT/Routing issue

    - by arul
    I have basic NAT/Routing problem with Mikrotik RB750 that I've been unable to solve over the past days. From our ISP we have 26 IP addresses: 10.10.10.192/27, with 10.10.10.193 being the gateway and 10.10.10.194 the first available IP. What I need is that everything connected to ether2 gets a public IP from the DHCP server, and everything connected to ether3 gets a local IP from another DHCP (192.168.100.0/24). All clients should have internet access (I'll figure out bandwidth throttling later) and optimally just 'see' each other (all boxes are Win7, I guess this can ultimately be handled with VPN). Here is my setup: ether1 (10.10.10.194) is connected directly to ISP. 20 clients connected to ether2(10.10.10.195), and another 20 to ether3(10.10.10.196) (both through same 24 port switches). This is my setup, which doesn't work, all 20 clients from ether2 can access the internet, though all comm. seems to come from 10.10.10.194 (is this due to the masquerade on ether1?), and ether3 can't access the internet at all. I think that I need to masquerade ether3, and SNAT/DNAT or NETMAP ether2, but that doesn't work either, I guess that I need to somehow 'wire' both ether2+3 to ether1. Address list: # ADDRESS NETWORK INTERFACE 0 ;;; public 10.10.10.194/32 10.10.10.192 ether1-gateway 1 ;;; inner DHCP 192.168.100.0/24 192.168.100.0 ether3-private 2 ;;; public 10.10.10.195/32 10.10.10.192 ether2-pub 3 ;;; public 10.10.10.196/32 10.10.10.192 ether3-private NAT 0 ;;; ether3 nat chain=srcnat action=src-nat to-addresses=10.10.10.196 src-address=192.168.100.0/24 out-interface=ether3-private 1 ;;; ether3 nat chain=dstnat action=dst-nat to-addresses=192.168.100.0/24 in-interface=ether3-private 2 ;;; ether1 masquerade chain=srcnat action=masquerade to-addresses=10.10.10.194 out-interface=ether1-gateway Routes: # DST-ADDRESS PREF-SRC GATEWAY DISTANCE 0 A S 0.0.0.0/0 ether1-gateway 1 2 A S 10.10.10.192/27 10.10.10.195 ether2-pub 1 3 ADC 10.10.10.192/32 10.10.10.195 ether2-pub 0 ether1-gateway ether3-private 4 ADC 192.168.100.0/24 192.168.100.0 ether3-private 0 IP Pools: # NAME RANGES 0 public-pool 10.10.10.201-10.10.10.220 1 private-pool 192.168.100.2-192.168.100.254 DHCP configs: # NAME INTERFACE RELAY ADDRESS-POOL LEASE-TIME ADD-ARP 0 public-dhcp ether2-pub public-pool 3d 1 private-dhcp ether3-private private-pool 3d Thanks!

    Read the article

  • Routing a PPTP client and VMware Server instance running on the same box

    - by servermanfail
    I have a Windows 2003 SBS box. It has 2 physical NIC's: WAN and LAN. The WAN is a public IP. The LAN is a simple 192.168.2.x subnet with Microsoft DHCP Server. Microsoft Routing and Remote Access Service is used to provide NAT to LAN. The box also runs VMware Server with a virtual machine running Windows XP. I want people to be able to VPN into the box, and connect to these virtual machines on the MSRDP port. I can VPN (PPTP) into the 2003 SBS box fine, as well as ping other machines on the LAN. I can ping the VM from a physical workstation on the LAN and vice-versa. I can ping the VPN client from the a physical workstation on the LAN and vice-versa. I can ping the VPN client from the Server console and vice-versa. I can ping the VM client from the Server console and vice-versa. But I cannot ping the VPN client from the VM and vice-versa. I was hoping to set up 2 or 3 Windows XP virtual machines on our only server, so that a couple of people can remote in to work without having to leave a physical machine on in the office. You could this attempted set up a "poor mans terminal server". On the 2003 SBS Server:- C:\Documents and Settings\Administrator>route print IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 50 56 c0 00 08 ...... VMware Virtual Ethernet Adapter for VMnet8 0x3 ...00 50 56 c0 00 01 ...... VMware Virtual Ethernet Adapter for VMnet1 0x10004 ...00 53 45 00 00 00 ...... WAN (PPP/SLIP) Interface 0x10005 ...00 11 43 d4 69 13 ...... Broadcom NetXtreme Gigabit Ethernet 0x10006 ...00 11 43 d4 69 14 ...... Broadcom NetXtreme Gigabit Ethernet #2 =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 81.123.144.22 81.123.144.21 1 81.123.144.20 255.255.255.252 81.123.144.21 81.123.144.21 1 81.123.144.21 255.255.255.255 127.0.0.1 127.0.0.1 1 81.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 86.135.78.235 255.255.255.255 81.123.144.22 81.123.144.21 1 109.152.62.236 255.255.255.255 81.123.144.22 81.123.144.21 1 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.2.0 255.255.255.0 192.168.2.3 192.168.2.3 1 192.168.2.3 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.26 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.28 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.32 255.255.255.255 127.0.0.1 127.0.0.1 50 192.168.2.50 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.255 255.255.255.255 192.168.2.3 192.168.2.3 1 192.168.10.0 255.255.255.0 192.168.10.1 192.168.10.1 20 192.168.10.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.10.255 255.255.255.255 192.168.10.1 192.168.10.1 20 192.168.96.0 255.255.255.0 192.168.96.1 192.168.96.1 20 192.168.96.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.96.255 255.255.255.255 192.168.96.1 192.168.96.1 20 224.0.0.0 240.0.0.0 81.123.144.21 81.123.144.21 1 224.0.0.0 240.0.0.0 192.168.2.3 192.168.2.3 1 224.0.0.0 240.0.0.0 192.168.10.1 192.168.10.1 20 224.0.0.0 240.0.0.0 192.168.96.1 192.168.96.1 20 255.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 255.255.255.255 255.255.255.255 192.168.2.3 192.168.2.3 1 255.255.255.255 255.255.255.255 192.168.10.1 192.168.10.1 1 255.255.255.255 255.255.255.255 192.168.96.1 192.168.96.1 1 Default Gateway: 81.123.144.22 =========================================================================== Persistent Routes: None C:\Documents and Settings\Administrator>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : 2003server Primary Dns Suffix . . . . . . . : mycompany.local Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : Yes WINS Proxy Enabled. . . . . . . . : Yes DNS Suffix Search List. . . . . . : mycompany.local gateway.2wire.net Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 8 Physical Address. . . . . . . . . : 00-50-56-C0-00-08 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.10.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 1 Physical Address. . . . . . . . . : 00-50-56-C0-00-01 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.96.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : PPP adapter RAS Server (Dial In) Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface Physical Address. . . . . . . . . : 00-53-45-00-00-00 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.32 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter LAN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet Physical Address. . . . . . . . . : 00-11-43-D4-69-13 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.50 Subnet Mask . . . . . . . . . . . : 255.255.255.0 IP Address. . . . . . . . . . . . : 192.168.2.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.2.3 Primary WINS Server . . . . . . . : 192.168.2.3 Ethernet adapter WAN: Connection-specific DNS Suffix . : gateway.2wire.net Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet #2 Physical Address. . . . . . . . . : 00-11-43-D4-69-14 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 81.123.144.21 Subnet Mask . . . . . . . . . . . : 255.255.255.252 Default Gateway . . . . . . . . . : 81.123.144.22 DHCP Server . . . . . . . . . . . : 10.0.0.1 DNS Servers . . . . . . . . . . . : 10.0.0.1 Primary WINS Server . . . . . . . : 192.168.2.3 NetBIOS over Tcpip. . . . . . . . : Disabled Lease Obtained. . . . . . . . . . : 25 February 2011 22:56:59 Lease Expires . . . . . . . . . . : 25 February 2011 23:06:59 C:\Documents and Settings\Administrator>ping 192.168.2.11 Pinging 192.168.2.11 with 32 bytes of data: Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128

    Read the article

  • Routing RFC1918 addresses through dd-wrt via a switch

    - by espenfjo
    I am a bit stuck with an experiment of mine. I have a network looking somewhat like this. | Internet | | ---- |Switch| ---- | | Server w/pub IP | DD-WRT router 192.168.1.1 | | RFC1918 clients 192.168.1.0/24 What I want is for the RFC1918 clients to speak directly with each others. On the server with the public IP I have this route: 192.168.1.0/24 dev eth0 scope link and can see that packets are infact reaching the dd-wrt router for 192.168.1.1, even though if I get no answer. Trying to reach one of the RFC1918 clients from the public IP server will get no result, as the dd-wrt router is not announcing that network on to its external interface (arp who-has 192.168.1.107 tell xxx.xxx.xxx.xxx, but no answer). The router being an WLAN dd-wrt router has of course a load of routes, VLANs and interfaces: xxx.xxx.xxx.1 dev vlan2 scope link 192.168.1.0/24 dev br0 proto kernel scope link src 192.168.1.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.244 84.215.64.0/18 dev vlan2 proto kernel scope link src xxx.xxx.xxx.xxx 169.254.0.0/16 dev br0 proto kernel scope link src 169.254.255.1 127.0.0.0/8 dev lo scope link 0.0.0.0 via xxx.xxx.xxx.1 dev vlan2 xxx.xxx.xxx.xxx being the public IP, and xxx.xxx.xxx.1 being the default route for the public IP. I am not sure where to continue with this. I would recon that I both need routing on the dd-wrt router, as well as some iptables magic? Why do something this complex? Why not ;) Also, do not mind that "Internet" can get RFC1918 traffic, it wont go outside of the walls. EDIT 1: Following the tip from stew I do indeed get the correct ARP flowing. And adding an iptables rule for allowing traffic from that specific public IPd machine I get traffic between the systems! Oddly enough though, the speed I get from Server w/pub IP - RFC1918 clients are the same as if the traffic were routed out onto the Internet and back. Edit 2: Ok, disconnecting the external Internet connection will still give the same, crappy transfer speed. So it has to be something else. Edit 3: Ok, I guess there are other reasons for this crappy speed. Case closed. :)

    Read the article

  • Virtualbox - routing subnet to bridge adapters

    - by user42384
    Hello, I have set up a Debian Lenny box with 3 vbox Lenny machines running eth0 of the host in bridged mode (on virtualbox 3.1.6). When testing in my local LAN, this all worked perfectly well and traffic flowed to and from the IPs of the virtual machines as it should. However, now that it's in its co-lo home, the networking setup is a bit different, and I'm unable to get traffic to flow to the vboxes properly. Specifically, the host has its own Primary IP, and I have a separate subnet of 8 (6 usable) IPs routed to the box for use by the vboxes. So, eth0 on host is: Machine IP: 2x.x.x.137 Gateway IP: 2x.x.x.138 Subnet Msk: 255.255.255.252 Subnet for vboxes is Subnet: 2x.x.x.240/29 Netmask: 255.255.255.248 vbox1 is configured to 2x.x.x.241 on eth0 as follows: auto eth0 iface eth0 inet static address 2x.x.x.241 netmask 255.255.255.248 Setting up a virtual interface (eth0:0) on the host with one of these subnet IPs allows me to ping to that address only from vbox1, and it allows me to ping vbox1 from the host. I can also ping that virtual interface perfectly well from outside, so the IPs are definitely landing at my machine. It seems I'm missing some sort of routing instruction either on the host or vbox1 to get traffic moving between the subnet and the default gateway, but I can't seem to figure out what it should be, or what glaringly obvious thing i'm missing. Most of my obvious attempts (the gw of eth0, the ip of eth0) were rejected by route command with SIOCADDRT: No such device (eg - i can't find it). I tried setting vbox1 to bridge on eth0:0, but this was not an acceptable device name and VBoxHeadless refused to start. The physical machine does have an unused physical NIC at eth1 that can be used if necessary for something or other. Host machine is running iptables configured by ferm, have experimented with it allowing forwarding for that subnet, but I wouldn't have thought this was necessary given the nature of the virtualbox devices (nor did it actually work). Clearing out all of these rules for a blank iptables set does not resolve the issue. (you can see ferm generated iptables at http://codedumper.com/ojaze) Thanks for any help you can give... Patrick

    Read the article

  • routing specific IP to ppp0 tunnel

    - by gompertz
    Hi All, I feel I've struggled with this long enough and need some help. I have a pptp tunnel and am trying to route destination traffic from 208.85.40.20 to the pptp tunnel (ppp0). (Keen observers may recognize the ip as being that of pandora.com). I am doing all this configuration on a router... and I know it's not working successfully as traceroute yields nothing but astericks. I've pasted relevant outputs below: (with some "security" editing to the addresses) root@OpenWrt:~# ifconfig br0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28185 errors:0 dropped:0 overruns:0 frame:0 TX packets:24936 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4894242 (4.6 MiB) TX bytes:5941902 (5.6 MiB) eth0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:51829 errors:0 dropped:0 overruns:0 frame:0 TX packets:56824 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:11490288 (10.9 MiB) TX bytes:11857913 (11.3 MiB) Interrupt:4 eth2 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:15426 TX packets:9529 errors:21 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:423 (423.0 B) TX bytes:596036 (582.0 KiB) Interrupt:2 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:30 errors:0 dropped:0 overruns:0 frame:0 TX packets:30 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2300 (2.2 KiB) TX bytes:2300 (2.2 KiB) ppp0 Link encap:Point-Point Protocol inet addr:68.68.39.250 P-t-P:172.16.20.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:165 errors:2 dropped:0 overruns:0 frame:0 TX packets:68 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:7006 (6.8 KiB) TX bytes:3462 (3.3 KiB) vlan0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:28182 errors:0 dropped:0 overruns:0 frame:0 TX packets:33813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5006544 (4.7 MiB) TX bytes:6609774 (6.3 MiB) vlan1 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX inet addr:173.183.111.3 Bcast:173.183.111.255 Mask:255.255.224.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:23653 errors:0 dropped:0 overruns:0 frame:0 TX packets:23012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5522012 (5.2 MiB) TX bytes:4982944 (4.7 MiB) wds0.4915 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wds0.4915 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@OpenWrt:~# cat /etc/ppp/ip-up iptables -A FORWARD -t filter -i br0 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -t filter -i ppp0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o ppp0 -s 192.168.1.1/24 -d 0/0 -j MASQUERADE iptables -A forwarding_rule -o ppp0 -j ACCEPT iptables -A forwarding_rule -i ppp0 -j ACCEPT iptables -t nat -A postrouting_rule -o ppp0 -j MASQUERADE root@OpenWrt:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.16.20.1 * 255.255.255.255 UH 0 0 0 ppp0 208.85.40.20 * 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 * 255.255.255.0 U 0 0 0 br0 173.183.192.0 * 255.255.224.0 U 0 0 0 vlan1 default d173-183-192-1. 0.0.0.0 UG 0 0 0 vlan1 default 192.168.1.1 0.0.0.0 UG 0 0 0 br0 Any advice is greatly appreciated, I'm not too great with network but am pretty astute at learning ;-)

    Read the article

  • Linux IPTables / routing issue

    - by Jon
    Hi all, EDIT 1/3/10 22:00 GMT - rewrote some of it after further investigation It has been a while since I looked at IPtables and I seem to be worse than before as I can not seem to get my webserver online. Below is my firewall rules on the gateway server that is running the dhcp server accessing the net. The webserver is inside my network on a static IP (192.168.0.98, default port). When I use Nmap or GRC.com I see that port 80 is open on the gateway server but when I browse to it, (via public URL. http://www.houseofhawkins.com) it always fails with a connection error, (nmap cannot connect and figure out what the web server is either). I can nmap the webserver and browse to it just fine via same IP inside my network. I believe it is my IPTable rules that are not letting it through. Internally I can route all my requests. Each machine can browse to the website and traffic works just fine. I can MSTSC / ssh to all the webservers internally and they inturn can connect to the web. IPTABLE: *EDIT - Added new firewall rules 2/3/10 * #!/bin/sh iptables="/sbin/iptables" modprobe="/sbin/modprobe" depmod="/sbin/depmod" EXTIF="eth2" INTIF="eth1" load () { $depmod -a $modprobe ip_tables $modprobe ip_conntrack $modprobe ip_conntrack_ftp $modprobe ip_conntrack_irc $modprobe iptable_nat $modprobe ip_nat_ftp echo "enable forwarding.." echo "1" > /proc/sys/net/ipv4/ip_forward echo "enable dynamic addr" echo "1" > /proc/sys/net/ipv4/ip_dynaddr # start firewall # default policies $iptables -P INPUT DROP $iptables -F INPUT $iptables -P OUTPUT DROP $iptables -F OUTPUT $iptables -P FORWARD DROP $iptables -F FORWARD $iptables -t nat -F #echo " Opening loopback interface for socket based services." $iptables -A INPUT -i lo -j ACCEPT $iptables -A OUTPUT -o lo -j ACCEPT #echo " Allow all connections OUT and only existing and related ones IN" $iptables -A INPUT -i $INTIF -j ACCEPT $iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A OUTPUT -o $EXTIF -j ACCEPT $iptables -A OUTPUT -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A FORWARD -i $EXTIF -o $INTIF -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A FORWARD -i $INTIF -o $EXTIF -j ACCEPT $iptables -A FORWARD -j LOG --log-level 7 --log-prefix "Dropped by firewall: " $iptables -A INPUT -j LOG --log-level 7 --log-prefix "Dropped by firewall: " $iptables -A OUTPUT -j LOG --log-level 7 --log-prefix "Dropped by firewall: " #echo " Enabling SNAT (MASQUERADE) functionality on $EXTIF" $iptables -t nat -A POSTROUTING -o $EXTIF -j MASQUERADE $iptables -A INPUT -i $INTIF -j ACCEPT $iptables -A OUTPUT -o $INTIF -j ACCEPT #echo " Allowing packets with ICMP data (i.e. ping)." $iptables -A INPUT -p icmp -j ACCEPT $iptables -A OUTPUT -p icmp -j ACCEPT $iptables -A INPUT -p udp -i $INTIF --dport 67 -m state --state NEW -j ACCEPT #echo " Port 137 is for NetBIOS." $iptables -A INPUT -i $INTIF -p udp --dport 137 -j ACCEPT $iptables -A OUTPUT -o $INTIF -p udp --dport 137 -j ACCEPT #echo " Opening port 53 for DNS queries." $iptables -A INPUT -p udp -i $EXTIF --sport 53 -j ACCEPT #echo " opening Apache webserver" $iptables -A PREROUTING -t nat -i $EXTIF -p tcp --dport 80 -j DNAT --to 192.168.0.96:80 $iptables -A FORWARD -p tcp -m state --state NEW -d 192.168.0.96 --dport 80 -j ACCEPT } flush () { echo "flushing rules..." $iptables -P FORWARD ACCEPT $iptables -F INPUT $iptables -P INPUT ACCEPT echo "rules flushed" } case "$1" in start|restart) flush load ;; stop) flush ;; *) echo "usage: start|stop|restart." ;; esac exit 0 route info: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 5e0412a6.bb.sky * 255.255.255.255 UH 0 0 0 eth2 192.168.0.0 * 255.255.255.0 U 0 0 0 eth1 default 5e0412a6.bb.sky 0.0.0.0 UG 100 0 0 eth2 ifconfig: eth1 Link encap:Ethernet HWaddr 00:22:b0:cf:4a:1c inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::222:b0ff:fecf:4a1c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:79023 errors:0 dropped:0 overruns:0 frame:0 TX packets:57786 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:11580918 (11.5 MB) TX bytes:22872030 (22.8 MB) Interrupt:17 Base address:0x2b00 eth2 Link encap:Ethernet HWaddr 00:0c:f1:7c:45:5b inet addr:94.4.18.166 Bcast:94.4.18.166 Mask:255.255.255.255 inet6 addr: fe80::20c:f1ff:fe7c:455b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:57038 errors:0 dropped:0 overruns:0 frame:0 TX packets:34532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:21631721 (21.6 MB) TX bytes:7685444 (7.6 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1517 (1.5 KB) TX bytes:1517 (1.5 KB) EDIT OK so as requested I will try and expand on my infrastructure: I previously had it setup with a Sky broadband modem router that did the DHCP and I used its web interface to port forward the web across to the web server. The network looked something like this: I have now replaced the sky modem with a dlink modem which gives the IP to the gateway server that now does the DHCP. It looks like: The internet connection is a standard broadband connection with a dynamic IP, (use zoneedit.com to keep it updated). I have tried it on each of the webservers(one Ubuntu Apache server and one WS2008 IIS7). I think there must also be an issue with my IPTable rules as it can route to my win7 box which has the default IIS7 page and that would not display when I forwarded all port 80 to it. I would be really grateful for any and all help with this. Thanks Jon

    Read the article

  • Using IIS Application Request Routing (ARR) for ASP.NET MVC

    - by Malcolm Frexner
    I use a simple ASP.NET MVC web (the template you use when you create a new site) and the web works as expected in my live environment. I now try to use IIS Application Request Routing version 2. I have a rule that send all reuqests to a different server that match a rule. The settings are a bit like this: http://blogs.iis.net/wonyoo/archive/2008/07/09/application-request-routing-arr-as-a-reverse-proxy.aspx My rule is just a bit different it is /shop(.*). Only requests that contain shop are send to a different server. I have to use rewrite, not redirect (The same as in the Picture) This works as long as the web the original requests go to is no ASP.NET MVC web. I tried to use a plain htm file in the webfolder and it worked. If put a compiled ASP.NET application into the webfolder it worked. But as soon as I put an ASP.NET MVC web into the folder, request arr served by this application. My understanding is that the ARR should kick in before the web application gets the chance to handle the request. Did anybody use ARR sucessfully as a reverse proxy for a ASP.NET MVC web? EDIT Here is the resulting web config when the rewrite roule is entered. With this rule I get a 404 that indicates that the rule is not used. <?xml version="1.0" encoding="UTF-8"?> <configuration> <configSections> <sectionGroup name="system.web.extensions" type="System.Web.Configuration.SystemWebExtensionsSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <sectionGroup name="scripting" type="System.Web.Configuration.ScriptingSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <section name="scriptResourceHandler" type="System.Web.Configuration.ScriptingScriptResourceHandlerSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <sectionGroup name="webServices" type="System.Web.Configuration.ScriptingWebServicesSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <section name="jsonSerialization" type="System.Web.Configuration.ScriptingJsonSerializationSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="Everywhere" /> <section name="profileService" type="System.Web.Configuration.ScriptingProfileServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <section name="authenticationService" type="System.Web.Configuration.ScriptingAuthenticationServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <section name="roleService" type="System.Web.Configuration.ScriptingRoleServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> </sectionGroup> </sectionGroup> </sectionGroup> </configSections> <appSettings /> <connectionStrings> <add name="ApplicationServices" connectionString="data source=.\SQLEXPRESS;Integrated Security=SSPI;AttachDBFilename=|DataDirectory|aspnetdb.mdf;User Instance=true" providerName="System.Data.SqlClient" /> </connectionStrings> <system.web> <!-- Set compilation debug="true" to insert debugging symbols into the compiled page. Because this affects performance, set this value to true only during development. --> <compilation debug="false"> <assemblies> <add assembly="System.Core, Version=3.5.0.0, Culture=neutral, PublicKeyToken=B77A5C561934E089" /> <add assembly="System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add assembly="System.Web.Abstractions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add assembly="System.Web.Routing, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add assembly="System.Web.Mvc, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add assembly="System.Data.DataSetExtensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=B77A5C561934E089" /> <add assembly="System.Xml.Linq, Version=3.5.0.0, Culture=neutral, PublicKeyToken=B77A5C561934E089" /> <add assembly="System.Data.Linq, Version=3.5.0.0, Culture=neutral, PublicKeyToken=B77A5C561934E089" /> </assemblies> </compilation> <!-- The <authentication> section enables configuration of the security authentication mode used by ASP.NET to identify an incoming user. --> <authentication mode="Forms"> <forms loginUrl="~/Account/LogOn" timeout="2880" /> </authentication> <membership> <providers> <clear /> <add name="AspNetSqlMembershipProvider" type="System.Web.Security.SqlMembershipProvider, System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" connectionStringName="ApplicationServices" enablePasswordRetrieval="false" enablePasswordReset="true" requiresQuestionAndAnswer="false" requiresUniqueEmail="false" passwordFormat="Hashed" maxInvalidPasswordAttempts="5" minRequiredPasswordLength="6" minRequiredNonalphanumericCharacters="0" passwordAttemptWindow="10" passwordStrengthRegularExpression="" applicationName="/" /> </providers> </membership> <profile> <providers> <clear /> <add name="AspNetSqlProfileProvider" type="System.Web.Profile.SqlProfileProvider, System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" connectionStringName="ApplicationServices" applicationName="/" /> </providers> </profile> <roleManager enabled="false"> <providers> <clear /> <add connectionStringName="ApplicationServices" applicationName="/" name="AspNetSqlRoleProvider" type="System.Web.Security.SqlRoleProvider, System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" /> <add applicationName="/" name="AspNetWindowsTokenRoleProvider" type="System.Web.Security.WindowsTokenRoleProvider, System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" /> </providers> </roleManager> <!-- The <customErrors> section enables configuration of what to do if/when an unhandled error occurs during the execution of a request. Specifically, it enables developers to configure html error pages to be displayed in place of a error stack trace. <customErrors mode="RemoteOnly" defaultRedirect="GenericErrorPage.htm"> <error statusCode="403" redirect="NoAccess.htm" /> <error statusCode="404" redirect="FileNotFound.htm" /> </customErrors> --> <pages> <controls> <add tagPrefix="asp" namespace="System.Web.UI" assembly="System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add tagPrefix="asp" namespace="System.Web.UI.WebControls" assembly="System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </controls> <namespaces> <add namespace="System.Web.Mvc" /> <add namespace="System.Web.Mvc.Ajax" /> <add namespace="System.Web.Mvc.Html" /> <add namespace="System.Web.Routing" /> <add namespace="System.Linq" /> <add namespace="System.Collections.Generic" /> </namespaces> </pages> <httpHandlers> <remove verb="*" path="*.asmx" /> <add verb="*" path="*.asmx" validate="false" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add verb="*" path="*_AppService.axd" validate="false" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add verb="GET,HEAD" path="ScriptResource.axd" type="System.Web.Handlers.ScriptResourceHandler, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" validate="false" /> <add verb="*" path="*.mvc" validate="false" type="System.Web.Mvc.MvcHttpHandler, System.Web.Mvc, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </httpHandlers> <httpModules> <add name="ScriptModule" type="System.Web.Handlers.ScriptModule, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="UrlRoutingModule" type="System.Web.Routing.UrlRoutingModule, System.Web.Routing, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </httpModules> </system.web> <system.codedom> <compilers> <compiler language="c#;cs;csharp" extension=".cs" warningLevel="4" type="Microsoft.CSharp.CSharpCodeProvider, System, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"> <providerOption name="CompilerVersion" value="v3.5" /> <providerOption name="WarnAsError" value="false" /> </compiler> <compiler language="vb;vbs;visualbasic;vbscript" extension=".vb" warningLevel="4" type="Microsoft.VisualBasic.VBCodeProvider, System, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"> <providerOption name="CompilerVersion" value="v3.5" /> <providerOption name="OptionInfer" value="true" /> <providerOption name="WarnAsError" value="false" /> </compiler> </compilers> </system.codedom> <system.web.extensions /> <!-- The system.webServer section is required for running ASP.NET AJAX under Internet Information Services 7.0. It is not necessary for previous version of IIS. --> <system.webServer> <rewrite> <rules> <rule name="shop" stopProcessing="true"> <match url="^shop/([_0-9a-z-.]+)" /> <action type="Rewrite" url="article.aspx?title={R:1}" logRewrittenUrl="true" /> </rule> </rules> </rewrite> <validation validateIntegratedModeConfiguration="false" /> <modules runAllManagedModulesForAllRequests="true"> <remove name="ScriptModule" /> <remove name="UrlRoutingModule" /> <add name="ScriptModule" preCondition="managedHandler" type="System.Web.Handlers.ScriptModule, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="UrlRoutingModule" type="System.Web.Routing.UrlRoutingModule, System.Web.Routing, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </modules> <handlers> <remove name="WebServiceHandlerFactory-Integrated" /> <remove name="ScriptHandlerFactory" /> <remove name="ScriptHandlerFactoryAppServices" /> <remove name="ScriptResource" /> <remove name="MvcHttpHandler" /> <remove name="UrlRoutingHandler" /> <add name="ScriptHandlerFactory" verb="*" path="*.asmx" preCondition="integratedMode" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="ScriptHandlerFactoryAppServices" verb="*" path="*_AppService.axd" preCondition="integratedMode" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="ScriptResource" preCondition="integratedMode" verb="GET,HEAD" path="ScriptResource.axd" type="System.Web.Handlers.ScriptResourceHandler, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="MvcHttpHandler" preCondition="integratedMode" verb="*" path="*.mvc" type="System.Web.Mvc.MvcHttpHandler, System.Web.Mvc, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="UrlRoutingHandler" preCondition="integratedMode" verb="*" path="UrlRouting.axd" type="System.Web.HttpForbiddenHandler, System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" /> </handlers> </system.webServer> </configuration>

    Read the article

  • Selecting which IP address to use for outgoing requests from behind a NAT

    - by iamrohitbanga
    Our organization has several external IP addresses. I am behind 2 layers of NAT and the servers choose which IP address to route my traffic to. Can I specify which IP address to use when finally leaving the organizations network. I know that source routing can be done in IPv4 by adding some options in the header. But can I configure my PC to add these options automatically. I have both a Windows and a Linux Machine.

    Read the article

  • Asp.Net 3.5 Routing to Asmx Webservice?

    - by Maushu
    I was looking for a way to route http://www.example.com/WebService.asmx to http://www.example.com/service/ using only the ASP.NET 3.5 Routing framework without needing to configure the IIS server. Until now I have done what most tutorials told me, added a reference to the routing assembly, configured stuff in the web.config, added this to the Global.asax: protected void Application_Start(object sender, EventArgs e) { RouteCollection routes = RouteTable.Routes; routes.Add( "WebService", new Route("service/{*Action}", new WebServiceRouteHandler()) ); } ...created this class: public class WebServiceRouteHandler : IRouteHandler { public IHttpHandler GetHttpHandler(RequestContext requestContext) { // What now? } } ...and the problem is right there, I don't know what to do. The tutorials and guides I've read use routing for pages, not webservices. Is this even possible? Ps: The route handler is working, I can visit /service/ and it throws the NotImplementedException I left in the GetHttpHandler method.

    Read the article

  • ASP.NET 3.5 Routing?

    - by Maushu
    I was looking for a way to route http://www.example.com/WebService.asmx to http://www.example.com/service/ using only the ASP.NET 3.5 Routing framework without needing to configure the IIS server. Until now I have done what most tutorials told me, added a reference to the routing assembly, configured stuff in the web.config, added this to the Global.asax: protected void Application_Start(object sender, EventArgs e) { RouteCollection routes = RouteTable.Routes; routes.Add( "WebService", new Route("service/{*Action}", new WebServiceRouteHandler()) ); } ...created this class: public class WebServiceRouteHandler : IRouteHandler { public IHttpHandler GetHttpHandler(RequestContext requestContext) { // What now? } } ...and the problem is right there, I don't know what to do. The tutorials and guides I've read use routing for pages, not webservices. Is this even possible? Ps: The route handler is working, I can visit /service/ and it throws the NotImplementedException I left in the GetHttpHandler method.

    Read the article

  • Asp.Net 3.5 Routing to Webservice?

    - by Maushu
    I was looking for a way to route http://www.example.com/WebService.asmx to http://www.example.com/service/ using only the ASP.NET 3.5 Routing framework without needing to configure the IIS server. Until now I have done what most tutorials told me, added a reference to the routing assembly, configured stuff in the web.config, added this to the Global.asax: protected void Application_Start(object sender, EventArgs e) { RouteCollection routes = RouteTable.Routes; routes.Add( "WebService", new Route("service/{*Action}", new WebServiceRouteHandler()) ); } ...created this class: public class WebServiceRouteHandler : IRouteHandler { public IHttpHandler GetHttpHandler(RequestContext requestContext) { // What now? } } ...and the problem is right there, I don't know what to do. The tutorials and guides I've read use routing for pages, not webservices. Is this even possible? Ps: The route handler is working, I can visit /service/ and it throws the NotImplementedException I left in the GetHttpHandler method.

    Read the article

  • Choosing routing.yml based on user culture?

    - by Erland Wiencke
    In my Symfony application I would like to choose the routing.yml based on the current user's culture; 'en' => routing.en.yml 'no' => routing.no.yml and so forth. Any suggestion to how this can be done? Edit: I am not trying to do i18n this way - I use Symfony's built-in methods for that. I simply want "static" urls to reflect the user's language: /en/projects/internal/project-name /no/prosjekter/interne/prosjektnavn /fr/baguette/champs-elysee/foux-de-fafa Where "projects" is a module, the category "internal" and "project-name" are stored in the database.

    Read the article

  • What should one keep in mind when switching from traditional to RESTful routing in Rails?

    - by Brian Holder-Chow
    What should one keep in mind when switching from traditional to RESTful routing in Rails? From a typical Rails routes.rb file: # This is a legacy wild controller route that's not recommended for RESTful applications. # Note: This route will make all actions in every controller accessible via GET requests. match ':controller(/:action(/:id))(.:format)' As switching away from this means that I will have to create routes for each controller individually, does anyone have any advice on the best way to migrate this safely?

    Read the article

  • routing table permissions under Windows 7 and openvpn

    - by pilcrow
    My ovpn client, 32-bit OpenVPN 2.1.1 on 64-bit Windows 7 Pro, cannot accept routes pushed to it by my remote endpoint ovpn server. This happens even if I invoke OpenVPN as a member of Administrators, and whether or not I've specified script-security 2 (as suggested by [this question][2]). Mon Mar 29 12:57:19 2010 Notified TAP-Win32 driver to set a DHCP IP/netmask of 192.168.254.3/255.255.255.0 on interface {8BE2E9CF-F4C9-4A5E-98FD-E12DF1B6C3A4} [DHCP-serv: 192.168.254.3, lease-time: 86400] Mon Mar 29 12:57:19 2010 NOTE: FlushIpNetTable failed on interface [14] {GUID} (status=5) : Access is denied. Mon Mar 29 12:57:24 2010 TEST ROUTES: 8/8 succeeded len=8 ret=1 a=0 u/d=up Mon Mar 29 12:57:24 2010 C:\WINDOWS\system32\route.exe ADD 172.20.1.0 MASK 255.255.255.0 192.168.254.1 Mon Mar 29 12:57:24 2010 ROUTE: route addition failed using CreateIpForwardEntry: Access is denied. [status=5 if_index=14] Mon Mar 29 12:57:24 2010 Route addition via IPAPI failed [adaptive] Mon Mar 29 12:57:24 2010 Route addition fallback to route.exe Mon Mar 29 12:57:24 2010 ERROR: Windows route add command failed [adaptive]: returned error code 1 ... and so on for each specific route the server pushes out. It doesn't seem right to me that the administrative user, the one configured at Windows 7 install time, should need further privileges. What am I missing?

    Read the article

  • one way routing

    - by user101531
    I have two computers connected with VPN, and some virtual machines on each. I want everything to see each other (that is basically 4 different networked machines). What I've not managed so far is that a computer on the one end to be visible to the other end. In tracert terms: 192.168.78.42>tracert 192.168.69.18 Tracing route to WIN-2K8R2 [192.168.69.18] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 192.168.78.17 2 * * * Request timed out. 3 217 ms 78 ms 78 ms WIN-2K8R2 [192.168.69.18] Trace complete. 192.168.78.42>tracert 192.168.69.112 Tracing route to 192.168.69.112 over a maximum of 30 hops 1 <1 ms <1 ms <1 ms 192.168.78.17 2 333 ms * 337 ms WIN-2K8R2 [192.168.86.22] 3/4/5 * * * Request timed out. 6 ^C 192.168.69.18>tracert 192.168.69.112 Tracing route to 192.168.69.112 over a maximum of 30 hops 1 <1 ms <1 ms <1 ms 192.168.69.112 Trace complete. 192.168.69.112>tracert 192.168.78.42 Tracing route to 192.168.78.42 over a maximum of 30 hops 1 1 ms * <1 ms 192.168.69.18 2 79 ms 77 ms 80 ms 192.168.86.21 3 80 ms 77 ms 81 ms 192.168.78.42 Trace complete. Note: the 4 machines are 192.168.69.112 (winXP), 192.168.69.18=192.168.86.22 (win2K8R2), 192.168.86.21=192.168.78.17 (Linux), 192.168.78.42 (win2K3). The VPN is a TAP openvpn connection between 192.168.86.21 and 192.168.86.22. I would say that the problem is in the win2K8 machine, but Windows networking is my weak point.

    Read the article

  • pfSense with two WANs, routing skype traffic over a specific WAN

    - by Eric
    I have a pfSense setup with two WANs (WAN1 and WAN2) and one LAN network. The two WANs are setup for failover. However, QoS has recently been an issue for skype calls in our office place (about 30 people) so we want to dedicate WAN2 for skype traffic (we use skype for all voip calls, etc.) As Skype is notoriously difficult to deal with, does anyone have any suggestions on how I should deal with this? A simple rile based on ports will not work, and using layer7 inspection witha skype porfile on all incoming LAN packets doesn't seem like the way to go eiter. here is a related pfsense forum post: http://forum.pfsense.org/index.php/topic,50406.msg268520.html#msg268520

    Read the article

  • Static routing on a TP-Link TL-WR1043ND

    - by igor
    My home network setup looks like this: Both routers are TP-Link TL-WR1043ND routers. The basement router handles all devices in the house that are connected via cable, handing out addresses for the 10.89.49.0/24 network via DHCP. Wireless doesn’t really work from the basement, as the signal is too weak, so I have disabled it. To do WiFi, I have added a second (identical) router downstairs. On the WAN side it is assigned the 10.89.49.101 IP address from the basement router, and on its LAN it provides the 10.89.7.0/24 network. Basic internet access works flawlessly from any device this way. I am now facing the problem that I am not able to communicate (e.g. SSH) between all devices, wired or wireless. I am able to connect from a wireless device to a wired device, for example SSH-ing from 10.89.7.X to 10.89.49.Y, but it doesn’t work the other way round—despite the fact that I have added a static route to the basement router: Does anybody have any idea on how to solve it? Both routers have already been upgraded to use the most recent firmware from TP-Link.com (Build 110429), to no avail. Errata: I would like to stick with the official firmware, switching to something like DD-WRT or OpenWrt only as a last resort.

    Read the article

  • Nginx dynamic upstream configuration / routing

    - by Dan Sosedoff
    I was experimenting with dynamic upstream configuration for nginx and cant find any good solution to implement upstream configuration from third-party source like redis or mysql. The idea behind it is to have a single file configuration in primary server and proxy requests to various app servers based on environment conditions. Think of dynamic deployments where you have X servers that are running Y workers on different ports. For instance, i create a new app and deploy. App manager selects a server and then rolls out a worker (Ruby/PHP/Python) and then reports the ip:port to the central database with status "up". At this time when i go to the given url nginx should proxy all requests to the specified ip:port upstream. The whole thing is pretty similar to what heroku does, except this proof-of-concept is not supposed to be production ready, mostly for internal needs. The easiest solution i found was using resolver with ruby-based DNS server. It works, nginx gets the IP address correctly, but the only problem is that you cant define port number for that IP. Second solution (which i havent tried yet) is to roll something else as a proxy server, maybe written in Erlang. In this case we need to use something to serve static content. Any ideas how to implement this in more flexible and stable way? P.S. Some research options: http://openresty.org/#DynamicRoutingBasedOnRedis https://github.com/nodejitsu/node-http-proxy

    Read the article

  • Sonicwall routing between multiple subnets on multiple interfaces

    - by Rain
    As shown by the network diagram below, I have two completely separate networks. One is being managed by a Sonicwall NSA 220, the other by some other router (the brand is not important). My goal is to allow devices within the 192.168.2.0/24 network to access devices in the 192.168.3.0/24 network. Allowing the reverse (192.168.3.0/24 - 192.168.2.0/24) is not required. So far, I have done the following: I connected the X3 Interface on the Sonicwall to the 192.168.3.0/24 network switch (shown as the dashed red line in the diagram). Next, I gave it a static ip address of 192.168.3.254 and set the Zone to LAN (the same Zone for the X0 interface). Judging by various articles and KBs I've read, this is all that should be necessary, although it does not work. I can ping 192.168.3.254 from any device in the 192.168.2.0/24 network although I cannot ping/connect to any device within the 192.168.3.0/24 network. Any help would be greatly appreciated! Network Diagram: (I asked a similar, yet more complicated, question earlier; although, I realized that I cannot solve that without first solving this (which may actually solve my original question))

    Read the article

  • Inter-vlan routing issues

    - by DKNUCKLES
    I've been brought in to help administer a network and I've run into an issue - I'm not sure why this one is beyond me, however I figure an extra set of eyes on the problem may help resolve the issue. I have an HP MSM720 controller and at the time I'm trying to set up a basic hotspot set up with access points. For the time being I'm just looking to have people authenticate with a PSK and access the internet and other resources (namely printers) on other vlans. The user authenticates and the DHCP server on the controller gives them a 192.168.1.0/24 address. They are able to successfully browse the internet and ping machines on other networks, however they are unable to print to network printers that sit on the same LANs as the very computers that wireless clients can ping. The (extremely simplified) topology is as follows Computers on the wireless 192.168.1.1 network are able to ping computers on the 192.168.0.0 network, however cannot ping or print to the printers on the same network. I'm baffled and I have no idea why this is the case. Can anyone shed some light on this for me? Can someone spot the error of my configuration? EDIT : It should be noted that for whatever reason other computers on the 10.0.100.0/24 network cannot even ping the gateway of the Wireless Access network (192.168.1.1) - I'm not sure if this is relevant. These are the VLANS listed on the controller.

    Read the article

  • Public IP Routing over Private GRE tunnel

    - by Paul
    I have a GRE tunnel configured between two linux boxes. The tunnel works fine. I can ping from each host the other private ip. Head privateip: 10.0.0.1 publicip: 8.8.8.8 Tail privateip: 10.0.0.2 publicip: 7.7.7.7 The public IP on Tail has the network block 9.9.9.0/23 statically routed over the 7.7.7.7 interface. The idea is to make the 9.9.9.0/23 ips work on servers on the 8.8.8.8 network. I configure the tail host to route the /23 block. I mounted a 9.9 IP on the head server. I can ping the 9.9 ip from the tail to the head. I can't ping the 9.9 ip from the public internet. I think I need to add some other routes because of gateway issues, but I can't seem to wrap my mind around it (not a router guy, just beating my way through something that I have never done before and vaguely understand) --danks

    Read the article

  • Web Server Routing Based On Location

    - by Eric
    I have a website that has users from both Hong Kong and Australia. Unfortunately, since the server is located in Australia, users from Hong Kong are going to suffer latency problems. Traffic has to go through US before travelling back to Australia. So I've setup a server in Hong Kong as well, and users using the .hk TLD are going to be redirected to the Hong Kong web server. It shares the same database server with the Australian server but due to aggressive SQL query caching, impact on performance from latency from SQL queries are negligible. But for users accustomed to the Hong Kong website but have since traveled to Australia, they suffer from additional latency because they go to the .hk site which redirects to the HK server even when they're in Australia. The website is targeted at international students from Hong Kong so this is an significant issue for me. Instead of redirecting users to the closest web server based on the TLD, how do I redirect users based on their location? Currently I am using nginx, postgres and Django. Say I know how to estimate users' location based on users' IP addresses, what is my next step? At what level would I work on? What topic should I read up?

    Read the article

< Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >