Search Results

Search found 10369 results on 415 pages for 'png 24'.

Page 60/415 | < Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >

  • AMD Radeon 7900 series: setting up 3 monitors

    - by Nilzone-
    I have an AMD Radeon 7900 series, which should support up to 6 screens. I'm having problems getting my third one working. Im running windows 8, and have installed all the latest AMD drivers. My screens are: Samusng syncmaster S27D391HS Samusng syncmaster S24B350H Samusng syncmaster S24B350H The first 24" monitor I use HDMI to DVI cable. The second 24" I use VGA to DVI cable. Lastly, for the 27" I use HDMI cable. The result is, no matter what I do, I never get more than two screens on simultaneously. I have also tried getting a DisplayPort to HDMI cable to use for the 27", but Im not sure if it was passive or active (didn't say on the box, nor did I ask). So my question is: is an active displayport to HDMI the solution, or is there someting else Im overlooking? (I have read similar posts on this subject, but I use a slightly different combo of cables. That is why I made a post of my own as well)

    Read the article

  • set tap0 using virt-manager for bridged wireless

    - by DaveO
    After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

    Read the article

  • Graphic driver for Targa Now NT9231

    - by Lumio
    I thought of installing Xubuntu on my elder Targa Now nettop and didn't think about the driver option. So now I'm here with a fresh Xubuntu installation and looking for graphic drivers. I found someone who might have had a "good" result with SiS - and the package is already installed, but I can't get my xorg.conf right. This is how my xorg.conf looks like right now: Section "Device" Identifier "Configured Video Device" Driver "sis" EndSection Section "Monitor" Identifier "Screen 0" Modeline "1024x768_60.00" 64.11 1024 1080 1184 1344 768 769 772 795 -HSync +Vsync #HorizSync 30.0-62.0 #VertRefresh 50.0-70.0 EndSection Section "Screen" Identifier "Default Screen" Monitor "Configured Monitor" Device "Configured Video Device" DefaultDepth 24 SubSection "Display" Depth 24 Modes "1024x768" "800x600" EndSubSection EndSection Thanks for every help given!

    Read the article

  • IIS not listening over external network, all other traffic working

    - by Beuy
    Hello there, I have a very odd situation, I have a server (let's call it X) running 2008 R2 with two NIC's in it, one is connected to the work domain and has a subnet of 192.168.10.0/24 the other is connected to a ADSL connection and has a subnet of 192.168.1.0/24. The server has IIS installed. On the ADSL connection I have setup a dynamic dns and port forwarding to allow external HTTP, HTTPS, FTP and RDP connections. FTP and RDP are working fine however neither HTTP or HTTPS are working at all. I can browse the websites by going to localhost on the machine, the HTTP and HTTPS ports appear as "Filtered" when I try to scan them using PortQueryUI and browsers respond with a "Server took too long to load or was not responding" error. This was working fine just a few days ago, Windows firewall is disabled I don't have any software firewall on it. And I'm really lost. Any help would be great.

    Read the article

  • Should I split my website into different servers

    - by Nyxynyx
    I have a website where a user uploads photos, the photos gets resized and thumbnailed, and stored on the server. At the same time, there are some INSERTS into a MySQL table regarding the photo uploaded (like description, user id etc). The site currently runs off a managed VPS, and I love the support it provides. However it is expensive to store the many small photos and the resizing and thumbnailing processes do cause spikes on the app performance. (Amazon S3 is pretty expensive, especially considering the costs for uploading many small files) Question: Will it be a good idea to move the image processing operations and image storage to another server which is an unmanaged dedicated server with a much lower cost/gb and keep the current VPS for its 24/7 support and hosting the webapp? Or should I move the entire site to the dedicated server? VPS Specs 16 cores 2.4GHz (E5620) 1GB memory 60GB Storage 3.5TB transfer $43/mth Managed (24/7) Dedicated Specs i3 2130 2 cores 3.4+ GHz 16 GB DDR3 2 x 1TB SATA2 storage 15 TB transfer $79/mth Unmanaged (Weekdays support) Software used Apache PHP MySQL Solr PostgreSQL ImageMagick

    Read the article

  • Text not Being Placed Correctly In the Center

    - by ThatMacLad
    This is another noobish mistake from me but I've placed some text in my page but after adding some padding to my div tag it's impossible for me to place my Text in the vertical center. Here is a preview of my problem: The CSS: body { background-image: url(../images/body-bg.jpg); font-family: arial; } .cms-head { background-image: url(../images/cms-head.png); background-repeat: no-repeat; width: 850px; height: 50px; padding: 5px; margin-bottom: -10px; } .posts-list { background-image: url(../images/new-post-b.png);; width: 840px; height: 500px; padding: 5px; border-bottom: 1px solid #000000; } .content { width: 850px; height: 500px; margin-left: auto; margin-right: auto; } .edit-post-but { background-image: url(../images/new-button.png); background-repeat: no-repeat; width: 60px; height: 40px; } .post-title { width: 834px; height: 40px; background-image: url(../images/post-head.png); background-repeat: no-repeat; -moz-border-radius: 5px; -webkit-border-radius: 5px; margin-left: auto; margin-right: auto; padding: 5px; font-size: 20px; color: #ffffff; } .bottom { width: 850px; height: 50px; background-image: url(../images/cms-bot.png); background-repeat: no-repeat; } a:active, a:link, a:visited{ color: #ffffff; } a:hover{ text-decoration:none; } The HTML/PHP: <html> <head> <title>Blog Name | Edit Post</title> <link rel="stylesheet" href="css/cms.css" type="text/css" /> </head> <body> <div class="content"> <div class="cms-head"> <a href="newpost.php"><img src="images/new-button.png" /></a> <a href="#"><img src="images/rss-button.png" /></a> </div> <div class="posts-list"> <?php mysql_connect ('localhost', 'root', 'root') ; mysql_select_db ('tmlblog'); $result = mysql_query("SELECT timestamp, id, title FROM php_blog ORDER BY id DESC"); while($row = mysql_fetch_array($result)) { $date = date("l F d Y",$row['timestamp']); $id = $row['id']; $title = strip_tags(stripslashes($row['title'])); if (mb_strlen($title) >= 50) { $title = substr($title, 0, 50); $title = $title . "..."; } print("<div class='post-title'><a href=\"update.php?id=" . $id . "\"><img src='images/edit-button.png'></a>$title<br /></div>"); } mysql_close(); ?> </div> <div class="bottom"></div> </div> </body> </html>

    Read the article

  • Conditional formatting

    - by djerry
    I have a rather annoying format I need to implement. There are 2 cells, both containing a date (cell A and B). B contains a date (24-06-2011). Cell B should be colored if cell A is between a date range, based on cell B. So if cell A lies between cell B - 7 days and cell B - 11 days, then it should be triggered. So with numbers: If B is 24-06-2011 then the range (which is not in any cell in the spreadsheet) is 13-06-2011 until 17-06-2011. If the date in cell A (let's say 14-06-2011) is in that range, cell B should be colored. Any ideas?

    Read the article

  • postfix and chdir domain.com/admin/ failed

    - by senzacionale
    root@ubuntu-server:/var/log# telnet localhost 110 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. +OK Hello there. user [email protected] +OK Password required. pass MyPasswd -ERR chdir domain.com/admin/ failed Connection closed by foreign host. and mail.log Apr 24 12:36:41 ubuntu-server pop3d: Connection, ip=[::ffff:127.0.0.1] Apr 24 12:36:58 ubuntu-server pop3d: chdir domain.com/admin/: No such file or directory what can i do? how to set up this directories? MX records are set, domain is set,...

    Read the article

  • syslog ip ranges to specific files using `rsyslog`

    - by Mike Pennington
    I have many Cisco / JunOS routers and switches that send logs to my Debian server, which uses rsyslogd. How can I configure rsyslogd to send these router / switch logs to a specific file, based on their source IP address? I do not want to pollute general system logs with these entries. For instance: all routers in Chicago (source ip block: 172.17.25.0/24) to only log to /var/log/net/chicago. all routers in Dallas (source ip block 172.17.27.0/24) to only log to /var/log/net/dallas. Finally, these logs should be rotated daily for up to 30 days and compressed. NOTE: I am answering my own question

    Read the article

  • What are working xorg.conf settings for using a Matrox TripleHead2Go @ 5040x1050?

    - by Brendan Abel
    I'm trying to configure xorg.conf to correctly set the resolution of my screens. I'm using a matrox triplehead, so the monitor is a single 5040x1050 screen. Unfortunately, it's being incorrectly set to 3840x1024. Here is my xorg.conf: # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 260.19.06 (buildd@yellow) Mon Oct 4 15:59:51 UTC 2010 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "Matrox" HorizSync 31.5 - 80.0 VertRefresh 57.0 - 75.0 #Option "DPMS" Modeline "5040x1050@60" 451.27 5040 5072 6784 6816 1050 1071 1081 1103 #Modeline "5040x1050@59" 441.28 5040 5072 6744 6776 1050 1071 1081 1103 #Modeline "5040x1050@57" 421.62 5040 5072 6672 6704 1050 1071 1081 1103 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce 9800 GTX+" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "5040x1050" SubSection "Display" Depth 24 EndSubSection EndSection

    Read the article

  • Auto-rotate rotated images with mogrify

    - by Frank Presencia Fandos
    Some of my images have been taken rotated but kept this data. The problem is that, when using mogrify to convert them from JPG to png, that data seems to dissapear. For showing this problem, I think the best is to show the script and an screenshot. Script with the code. Put it in a text file, give it execution permission, double click, run (from terminal if you wish) and wait a while. All the JPGs in that folder will be converted to png. #! /bin/bash echo "Converting JPG to png. Please don't close this window." mogrify -alpha on -format png *.JPG mogrify -alpha on -format -alpha on png *.jpg It works great and adds an alpha channel. This is personally useful when I edit them later, not to add the channel individually. Now the screenshot that illustrates the problem: As you can see, the original ones' (JPGs) preview is right, the modified preview is wrong, the Shotwell rendering is right and the GIMP edit is wrong and didn't even say the image was rotated, as it uses to do with other images. How can I edit my script to preserve the orientation?

    Read the article

  • How do I enable JPEG Support for PHP?

    - by ngache
    My Configure Command doesn't say anything about jpg, nor gif/png, but I can see gif/png support in the output of phpinfo(). I built PHP with --with-gd, but only GIF Support and PNG Support are in the output of phpinfo(), how do I enable JPEG Support?

    Read the article

  • Motherboard memory question

    - by JERiv
    I am currently drawing up specs on a new workstation for my office. I am considering the Asus P6X58D for a motherboard. This board's specs list it as supporting 24 gigs of memory. Suppose I were to use six four gig memory cards and then two video cards with 1 gig of memory apiece. Is the maximum supported memory similar to how 32 bit operating systems only have enough address space for 4 gigs of memory? Simply: Will the board post? If so, will the system be able to address all the memory, both the 24 gigs on the ddr3 bus and the 3 gigs on the graphics card?

    Read the article

  • ASA 5505 8.4 open ports for subnet

    - by fwrawx
    I have an ASA 5505 running 8.4 with its outside interface plugged into our internal network. I want to open up access to hosts on one of the vlans behind that ASA to hosts on our internal network. I was just starting to grasp NAT on our older PIX but the ASA 8.4 has me confused now. Given a clean ASA with an outside vlan of 10.0.0.1/24 and test vlan of 10.0.1.1/24 what's the basic configuration needed to allow any hosts on the outside network to have access to any of the hosts on the test network?

    Read the article

  • RewriteRule applying pattern even though 1 of the RewriteCond's failed

    - by BHare
    #www. domain . tld RewriteCond %{HTTP_HOST} (?:.*\.)?([^.]+)\.(?:[^.]+)$ RewriteCond /home/%1/ -d RewriteRule ^(.+) %{HTTP_HOST}$1 RewriteRule (?:.*\.)?([^.]+)\.(?:[^.]+)/media/(.*)$ /home/$1/client/media/$2 [L] RewriteRule (?:.*\.)?([^.]+)\.(?:[^.]+)/(.*)$ /home/$1/www/$2 [L] Here is rewritelog output: #(4) RewriteCond: input='tfnoo.mydomain.org' pattern='(?:.*\.)?([^.]+)\.(?:[^.]+)$' [NC] => matched #(4) RewriteCond: input='/home/mydomain/' pattern='-d' => not-matched #(3) applying pattern '(?:.*\.)?([^.]+)\.(?:[^.]+)/media/(.*)$' to uri 'http://www.mydomain.org/files/images/logo.png' #(3) applying pattern '(?:.*\.)?([^.]+)\.(?:[^.]+)/(.*)$' to uri 'http://www.mydomain.org/files/images/logo.png' #(2) rewrite 'http://www.mydomain.org/files/images/logo.png' -> '/home/mydomain/www/logo.png' If you note on the 2nd 4 it failed the -d (if directory exists) pattern. Which is correct. mydomain does not have a /home/. Therefore it should never rewrite, atleast according to my understanding that all rewriterules are subject to rewriteconds as logical ANDs.

    Read the article

  • set tap0 using virt-manager for bridged wireless

    - by DaveO
    After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

    Read the article

  • Why can't my networks reach each other?

    - by HOLOGRAPHICpizza
    We have two Buffalo WZR-HP-G300NH2 routers, with the default firmware, DD-WRT v24SP2-MULTI (10/31/11) std - build 17798. Each has a separate cable internet connection with a public static IP address. They are both in the 24.123.68.0/24 space. Both of them can contact pretty much the whole internet, and they can both be accessed out on the internet with no problem, but for some reason they can't talk to each other! When I try to ping one from the other I always get "Destination Host Unreachable". There are no strange routing or firewall rules in place. And they are both set to respond to pings, I can ping them from outside. Our main IT guy is going to call our ISP on Monday, but I'm impatient, so does anyone have any ideas?

    Read the article

  • How to change .htaccess file to work right in localhost?

    - by Manolo Salsas
    I have this snippet code in my .htaccess file to prevent users from hotlinking the server's images: RewriteEngine On RewriteCond %{HTTP_REFERER} ^$ [OR] RewriteCond %{HTTP_REFERER} !^http://(www.)?itransformer.es/.*$ [NC] RewriteRule \.(gif|jpe?g|png|wbmp)$ http://itransformer.es [R,L] Of course, it is not working in my localhost, but don't know how to achieve it. My guess is that I should change the domain name with any wildcard. Any idea? Update I've finally found out the answer thanks to @Chris solution: RewriteCond %{HTTP_REFERER} ^$ [OR] RewriteCond %{HTTP_REFERER} ^https?://%{HTTP_HOST}/.*/usuarios/.*$ [NC] RewriteRule \.(gif|jpe?g|png|wbmp)$ http://%{HTTP_HOST} [R=301,L] The /usuarios/ directory is because I only want to deny direct access to files inside this directory. Update2 For some reason, it doesn't work again. Finally I think that I found out a better solution: RewriteCond %{REQUEST_FILENAME} .*/usuarios/.*$ [NC] RewriteRule \.(gif|jpe?g|png|wbmp)$ http://%{HTTP_HOST} [R=301,L] I say better solution because what I want to deny is direct access to a file (image). Update3 Well, after a while I discovered above wasn't exactly what I wanted, so the next is definitive: RewriteCond %{HTTP_REFERER} ^$ [OR] RewriteCond %{HTTP_REFERER} !^https?://itransformer.*$ [NC] RewriteRule /usuarios/.*\.(gif|jpe?g|png|wbmp)$ - [R=404,L] Just two doubts: If I change the above to: RewriteCond %{HTTP_REFERER} ^$ [OR] RewriteCond %{HTTP_REFERER} !^https?://%{HTTP_HOST}.*$ [NC] RewriteRule /usuarios/.*\.(gif|jpe?g|png|wbmp)$ - [R=404,L] it doesn't work. I don't understand why, because %{HTTP_HOST} is equal to itransformer in my localhost, and it should work. The second doubt is why is shown the default 404 page and not my custom page (that is shown in all other 404 responses).

    Read the article

  • routing through multiple subinterfaces in debian

    - by Kstro21
    my question is as simple as the title, i have a debian 6 , 2 NICs, 3 different subnets in a single interface, just like this: auto eth0 iface eth0 inet static address 192.168.106.254 netmask 255.255.255.0 auto eth0:0 iface eth0:0 inet static address 172.19.221.81 netmask 255.255.255.248 auto eth0:1 iface eth0:1 inet static address 192.168.254.1 netmask 255.255.255.248 auto eth1 iface eth1 inet static address 172.19.216.3 netmask 255.255.255.0 gateway 172.19.216.13 eth0 is conected to a swith with 3 differents vlans, eth1 is conected to a router. No iptables DROP, so, all traffic is allowed. Now, passing the traffic through eth0 is OK, passing the traffic through eth0:0 is OK, but, passing the traffic through eth0:1 is not working, i can ping the ip address of that sub interface from a pc where this ip is the default gateway, but can't get to servers in the subnet of the eth1 interface, the traffic is not passing, even when i set the iptables to log all the traffic in the FORWARD chain and i can see the traffic there, but, the traffic is not really passing. And the funny is i can do any the other way around, i mean, passing from eth1 to eth0:1, RDP, telnet, ping, etc, doing some work with the iptable, i manage to pass some traffic from eth0:1 to eth1, the iptables look like this: iptables -t nat PREROUTING -d 192.168.254.1/32 -p tcp -m multiport --dports 25,110,5269 -j DNAT --to-destination 172.19.216.1 iptables -t nat PREROUTING -d 192.168.254.1/32 -p udp -m udp --dport 53 -j DNAT --to-destination 172.19.216.9 iptables -t nat PREROUTING -d 192.168.254.1/32 -p tcp -m tcp --dport 21 -j DNAT --to-destination 172.19.216.11 iptables -t nat POSTROUTING -s 172.19.216.0/24 -d 172.19.221.80/29 -j SNAT --to-source 172.19.221.81 iptables -t nat POSTROUTING -s 172.19.216.0/24 -d 192.168.254.0/29 -j SNAT --to-source 192.168.254.1 iptables -t nat POSTROUTING -s 172.19.216.0/24 -o eth0 -j SNAT --to-source 192.168.106.254 dong this is working, but,it is really a headache have to map each port with the server, imagine if i move the service from server, so, now i have doubts: can debian route through multiple subinterfaces?? exist a limit for this?? if not, what i'm doing wrong when i have the same setup with other subnets and it is working ok?? without the iptables rules in the nat, it doesn't work thanks and i hope good comments/answers

    Read the article

  • Xen 4.1 host (dom0) with blktap disks ("tap:aio:") not connecting

    - by Manwe
    Problem using blktap with xen-4.1 running Ubuntu Precise stock kernel with dom0 xen-4.1. I get: [ 5.580106] XENBUS: Waiting for devices to initialise: 295s...290s. ... [ 300.580288] XENBUS: Timeout connecting to device: device/vbd/51713 (local state 3, remote state 1) And some syslog lines: May 17 13:07:30 localhost logger: /etc/xen/scripts/blktap: add XENBUS_PATH=backend/tap/10/51713 May 17 13:07:31 localhost logger: /etc/xen/scripts/blktap: Writing backend/tap/10/51713/hotplug-status connected to xenstore. with tap:aio: disk lines. file:/ works. disk = [ 'tap:aio:/data/root.img,xvda1,w', ] Problem exists with lucid and precises domU kernels and both guests work in Ubuntu hardy dom0 Host 64bit 2.6.24-28-xen xen-3.3 3.2.0-24-generic #37-Ubuntu SMP Wed Apr 25 08:43:22 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Distributor ID: Ubuntu Description: Ubuntu 12.04 LTS Release: 12.04 Codename: precise

    Read the article

  • How to route packets from Wi-Fi to Ethernet on OSX?

    - by Alexander Artemenko
    I have a trouble, configuring a home network. Here is how my devices are connected together: Internet     ? Wi-Fi Router ? MacBook     ? iMac ?ethernet cable? Synology NAS I have no ability to plugin NAS right into the Wi-Fi router. The problem is that MacBook does not see NAS, because they are in different networks — I configured Wi-Fi Router to serve 192.168.10.0/24 addresses, and configured iMac's ethernet connection to use 192.168.20/24 network. Is there a way to setup route from MacBook to the NAS?

    Read the article

  • Imagemagick convert creates monochrome output only

    - by rumtscho
    I have a book scan as a pdf. When I open it with Adobe Reader, it looks like grayscale. When I open it with IrfanView, it looks like grayscale, and the Information option tells me that the image is actually 24 bit (I don't know if this is the real bit depth of the image embedded in the pdf or if IrfanView assigns the maximal depth when opening a pdf as image). I want to OCR the scan with OmniPage SE. It doesn't read PDF, so I decided to use ImageMagick to convert the file to PNG first. But no matter what I try, the output is always monochrome and practically unreadable. I tried different conversion lines, with different depth, density and resize values, but it didn't help. What you see was made with the options convert testfile.pdf -density 600x600 -depth 8 PNG:testfile.png. Any idea what causes the problem? Edit: To make it clear, the output looks like this for any value of -density, -depth and -resize I have tried. It also looks like that when I use no options at all, as in convert testfile.pdf PNG:testfile.png.

    Read the article

  • Route eth0 to internet traffic and eth1 to local traffic

    - by Romain Caire
    How can I route all my internet traffic on eth0 (everything except 192.168.1.0/24) and route my local traffic through eth1 (192.168.1.0)? Here is my attempt : # Flush ALL THE THINGS. ip route flush table main # Restore the main table. I flushed it because OpenVPN does weird things to it. ip route add 127.0.0.0/8 via 127.0.0.1 dev lo ip route add 0.0.0.0/0 via 164.67.195.1 ip route add 192.168.1.0/24 via 192.168.1.1 ip route flush cache

    Read the article

  • Allow access to printer between interfaces on Cisco ASA5510

    - by Jonas Stensved
    I have a Cisco ASA5510 where we have to separate networks on two separate interfaces. The networks have and should have nothing to do with each other except that network B needs to access a printer on network A. Network A: 192.168.137.0/24 Printer: 192.168.137.20 Network B: 192.168.0.0/24 I've added an incoming rule from Network A to the Printer IP in the ASDM interface but clients can't print. Our previous router was configured to let traffic through so the clients on Network B is already configured so it think it should work if the traffic is allowed. How do I let clients on Network B communicate with the printer?

    Read the article

  • Why do I have no TTY on a basic Ubuntu 9.10 server install?

    - by pr1001
    I have reinstalled Ubuntu 9.10 Server several times on a bog standard 1RU server and each time I finish the install and reboot I see GRUB run and am then presented with a black screen. The machine is running just fine, as I am able to SSH in, but I can't see anything on the attached monitor. I have a simple LCD screen connected via VGA and a signal is apparently being output to it, as it doesn't go asleep. Looking at /var/log/syslog I see: Mar 24 14:57:44 bridge5 rsyslogd-2039: Could no open output file '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ] However, I later see: Mar 24 14:57:44 bridge5 kernel: [ 0.001368] console [tty0] enabled Any thoughts? Thanks!

    Read the article

< Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >