Search Results

Search found 6172 results on 247 pages for 'usb headset'.

Page 60/247 | < Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >

• Is it possible to use a bluetooth-enabled phone as handset?

  - by Andrea Spadaccini

  Hello, I'd like to use my cell phone (Nokia E71) as a handset for incoming calls in Skype/Empathy. I know this basically means that I have to configure it as a PulseAudio device, but I wasn't able to do that. Following a guide (in Italian, sorry), I installed pulseaudio-module-bluetooth and BlueMan, but the latter sees the phone as a "Smartphone", not allowing me choose other profiles. Can you help me? Thanks

  Read the article

• How can I make my Virtualbox Vista see my USB device (iPad)?

  - by phil

  I have the latest VirtualBox. I have filters for the iPad. But it does not show up in my virtual Windows vista My Computer screen or virtual iTunes. When I try to right click the little USB icon and select it it says it failed because the device is busy with a previous request Result code: E_INVALIDARG (0X80070057) Component: HostUSBDevice Interface: IHostUSBDevice {173b4b44-d268-4334-a00d-b6521c9a740a} Callee: IConsole {515e8e8d-f932-4d8e-9f32-79a52aead882} Any help is greatly appreciated Note: running 64bit Windows Vista Virtual on a 64bit Windows Vista (Home Premium) EDIT: my iPad is in recovery mode, maybe why it can't be seen in virtualbox? Also my host is running Zonealarm firewall and Microsoft Security Essentials. In addition the guest has AVG antivirus. Could those programs conflict with virtualbox?

  Read the article

• Super Uninstallers that can be run from a USB Flash Drive?

  - by JFV

  Does anyone know of a 'Super Uninstaller' package that will allow you to run it from a USB Flash Drive? I used to have a CD that was a Super Uninstaller utility that would uninstall anything. I can't seem to find it and I'd like to replace it with one that I can run from a flash drive. I'd like the portability to now have to install it on each computer I'm using it on. Any and all suggestions would be helpful! Thanks! JFV

  Read the article

• if a usb pen drive has 64349 cylinders, is it damaged?

  - by Andrew S

  I have a 4Gb USB pen drive that I'm trying to format with FAT32. When I run fdisk, it gives me this message: The number of cylinders for this disk is set to 64349. There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with: 1) software that runs at boot time (e.g., old versions of LILO) 2) booting and partitioning software from other OSs (e.g., DOS FDISK, OS/2 FDISK) I've tried deleting the partition table, creating new partitions, etc, but they never work. Sometimes I can write to the drive the first time I use it after formatting it, but then it becomes read-only in both Windows and Linux. I've tried this on multiple computers. Am I doing something wrong, or is the drive reporting an incorrect number of cylinders? Is the drive itself likely to be corrupted, and is there anyway to fix this under Windows Vista or Linux? Thanks

  Read the article

• Why is Windows 7 so slow to log-on when my Wireless USB dongle is plugged in?

  - by Sam

  I'm using an Edimax Wireless USB dongle (model EW-7711UTN) on Windows 7 64-bit. The dongle works brilliantly (it was truly plug-and-play) except for one thing. I've noticed that if the dongle is plugged in whilst I'm logging on to Windows it introduces a massive delay - after I type in my password and hit enter, Windows shows the "Welcome" screen, then the screen goes black for 2 minutes or so (with just the cursor showing) before finally displaying my desktop. If I unplug the dongle before I enter my password, Windows goes straight to my desktop. Even though the dongle didn't appear to need drivers for Windows 7, I did try downloading the latest ones from the Edimax website, but that made no difference.

  Read the article

• USB to DVI adapter to get around two monitor limit of my graphics card?

  - by JavaJosh94

  My graphics card is an nVidia GTS 450 which will only run two monitors at a time, but I'd like to add a third one. Will I be able to do that using a USB to DVI adapter or would the limit still be there? Also I've been told the video quality is really bad with these adapters, so is the quality of the video output by these adapters okay for things like web browsing and working on office thing? And is it worth the $60 or would I be better off just buying a cheep second card?

  Read the article

• Should I use VFAT or ext3 for a 1Tb external usb hard drive?

  - by ihuston

  I have a 1 Tb USB external hard drive which I want to use to backup data from my home and office desktops (both running Linux). Should I format the drive (possibly split into a few partitions) as vfat or ext3? I don't anticipate using the drive with Windows very often so this is not a primary concern. The main thing holding me back from just using ext3 is the problems you can have when two different users (home and work accounts) try to access each others data. Is there any way to mount an ext3 drive with user id mapping?

  Read the article

• Using VMware's ESXi, can I plug in 30 USB Wireless adapters and allow each of 30 VMs one?

  - by 31eee384

  I'm assuming ESXi will act very similarly to VMware Workstation or other products, so answers based on knowledge of those programs might also help. I want to plug in 30 USB Wireless or Ethernet adapters into my server, and let each VM access one and only one of these devices. Unfortunately, I don't have the hardware to just try it out as the purchase of hubs and adapters hinges on the result of this question. The answer could be a resounding "yes, easy!" and that would be great. I couldn't find any answers to this question with google, and it's possible that this is because it's so easy to do. Thanks!

  Read the article

• Can you boot/install/restore a MacBook Pro with a MacBook Air USB stick?

  - by zekel

  The new MacBook Airs don't have optical drives, so you can't install or restore the OS via DVD. They include a little USB stick for this purpose. I have a MacBook Pro and a MacBook Air. Does anyone know if it will work with my MacBook Pro? I'm thinking about removing my optical drive to put in another HD. The only sticky situation I might get into is if I need to do an install or restore on the road without an external DVD drive. (Good article on replacing optical drive with hard drive enclosure: remiel.info/post/1601242301/making-the-leap-to-ssd-on-a-macbook)

  Read the article

• Using VMware's ESXi, can I plug in 30 USB Wireless adapters and allow each of 30 VMs one?

  - by 31eee384

  I'm assuming ESXi will act very similarly to VMware Workstation or other products, so answers based on knowledge of those programs might also help. I want to plug in 30 USB Wireless or Ethernet adapters into my server, and let each VM access one and only one of these devices. Unfortunately, I don't have the hardware to just try it out as the purchase of hubs and adapters hinges on the result of this question. The answer could be a resounding "yes, easy!" and that would be great. I couldn't find any answers to this question with google, and it's possible that this is because it's so easy to do.

  Read the article

• How can one create a bootable linux usb key that works on Mac (Intel 64 bit CPU) hardware ?

  - by user3621

  Hi, I'm trying to create a bootable usb key with linux (debian) and that can be booted on Macintel hardware. I have read that MAC's EFI can only boot GPT GUID formatted disks. I'm desperately trying to find a good tutorial which explains how to create such a key. Here what I have done so far: create a GUID partition on te key using linux GNU parted create a HFS+ or ext3 partition on the key, with the boot flag on install a linux .iso with unetbootin While all steps were successfull and in some cases I could even boot on a PC, the step of booting on Macintel software failed (on a macbook). I need to precise that I holded the "alt" key while booting the mac and the only visible bootable disk was the hard disk. Thanks for any advice. PS: I have tried with rEFIt as well. In one case I had a "windows" icon but it then failed to boot with a message like "no system found"

  Read the article

• Do not get 'Safely remove' option in Tray for USB storage devices.

  - by blitzkriegz

  I had done some tweaks in service settings (Disabled some as I thought it is not needed). Now, I am not getting the option to safely remove mass storage device when I click the icon on the system tray. I tried enabling some of the services, but it didn't help. Moreover I'm not very sure if this anomaly is because of my changes in services. Any idea how to make those 'safely remove' options appear when I click the USB icon on the tray. Right now nothing is happening when I click.

  Read the article

• USB-based AV application that restores compromised Windows files from CD/DVD?

  - by overtherainbow

  Hello I just tried a couple of rescue disks (AVG and Kaspersky), and I was wondering if someone knew of a solution that would work like this: The AV solution boots from a USB key, and works entirely from RAM (where the latest virus DB is downloaded) The user inserts his Windows CD/DVD in the drive If any Windows file is compromised, the AV application fetches a clean version from the CD/DVD and restores it on the hard drive optionally, any compromised drive/user-land application is quarantied, and it is up to the user to reinstall those after he successfully rebooted into a restored Windows setup Have you heard of a solution like this? It seems silly to reinstall a whole Windows computer just because one or a few system files were compromised. Thank you.

  Read the article

• How do you interface with a USB to Parallel adapter?

  - by Hans

  I'm currently doing a project where I have to interact with a circuit I made through the parallel port of a computer. However, my computer doesn't have a parallel port so I borrowed a Parallel to USB adapter cable. The cable didn't come with any drivers, but it's recognized by the device manager as a "USB Printing Support" controller, under the USB section. It seems that old parallel printers can be plugged in and work properly without any problems. So my question is, if I write a program in Java that tries to interact with a parallel port directly, will it work? And if not, can anyone give me some pointers as to what I need to do to interact with it? Thanks.

  Read the article

• How can I use Java to communicate to device through USB port?

  - by Bopha

  I just recently learn Java and try to communicate to the device through USB port connection. I've have used C# with OpenNETCF which allows me to send file and retrieve file on the device through USB port; how can I achieve this with java? I seearch on stackoverflow thread, http://stackoverflow.com/questions/544507/how-to-communicate-with-a-usb-device-under-windows-and-java, the comment made by christoffer is to hack the native code, but I don't quite which native code api that he referred to. RAPI, maybe?

  Read the article

• How to generate a video signal from Android device via USB?

  - by C.Rivlaldo

  Is it possible to create an application for Android, which can generate a video signal (HDMI or VGA) via USB? Any Android device has miniUSB port. Theoretically it's possible to create a small commutator device on microcontroller or microscheme, which will be a USB-host for Android device. You'll connect Android device with commutator and then connect commutator with monitor. For example, the scheme looks like: Android phone - commutator (USB-host) - TV/Monitor. Summary, I need to connect android phone with TV via miniUSB port. I found soft which can use miniUSB - HDMI cable, but those apps only for Motorolla Droid and HTC Evo. I'll glad to get links to existing apps or projects on that theme, to info about software generation HDMI-signal and connecting Android devices with another devices. Thank you and sorry for my bad english!

  Read the article

• External 1TB WD USB 3.0 HDD is not detecting. Working perfectly find in Windows

  - by Yathi

  My 1TB USB 3.0 was working fine earlier in Ubuntu as well as Windows. But lately it is not at all being detected in Ubuntu. It still works fine in Windows. I did update my Ubuntu to 12.10 but I am not sure if that caused the issue. When I connect my HDD and run dmesg | tail: [ 47.804676] usb 4-3: >Device not responding to set address. [ 48.008575] usb 4-3: >Device not responding to set address. [ 48.212421] usb 4-3: >device not accepting address 9, error -71 [ 48.324451] usb 4-3: >Device not responding to set address. [ 48.528340] usb 4-3: >Device not responding to set address. [ 48.732165] usb 4-3: >device not accepting address 10, error -71 [ 48.844138] usb 4-3: >Device not responding to set address. [ 49.048179] usb 4-3: >Device not responding to set address. [ 49.251881] usb 4-3: >device not accepting address 11, error -71 [ 49.251907] hub 4-0:1.0: >unable to enumerate USB device on port 3 The output of sudo fdisk -l is : Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00030cde Device Boot Start End Blocks Id System /dev/sda1 2048 1332981759 666489856 83 Linux /dev/sda2 1332981760 1953523711 310270976 5 Extended /dev/sda5 1332983808 1349365759 8190976 82 Linux swap / Solaris /dev/sda6 1349367808 1953523711 302077952 7 HPFS/NTFS/exFAT Disk /dev/sdb: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders, total 234441648 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000a2519 Device Boot Start End Blocks Id System /dev/sdb1 * 2048 103368703 51683328 7 HPFS/NTFS/exFAT /dev/sdb2 103368704 154568703 25600000 83 Linux /dev/sdb3 154568704 234440703 39936000 7 HPFS/NTFS/exFAT /dev/sda and /dev/sdb are my 2 internal HDDs. But the external one which should be /dev/sdc is not even being shown though it is connected and the LED on the HDD is glowing. Someone had suggested adding blacklist uas to /etc/modprobe.d/blacklist.conf. Tried that as well. But still not working. Can someone help me out.

  Read the article

• I have static noise in my speakers and headset

  - by Kazarion

  I have been having a problem with my computer where I am constantly getting static from the point I turn on my PC. I have changed Towers, Hard Drives, added and removed a Sound Blaster Xtreme Sound Card, used 3 different Headsets, and 2 sets of speakers. Lately I have noticed random dips in my frame rates when playing games. Is there any possibility that the graphics card could be causing the static with the possibility of it needing to go in for repairs? Specs: i5-3570K 3.40 GHZ Gigabyte GTX 570 8GB of Corsair Ram MB ASUS|P8Z77-V Z77 3TB Seagate Barracude HDD Rosewill 850W PSU Corsair A70 Heatsink

  Read the article

• How to safely remove a USB device from 2008 Core server?

  - by Qwerty

  I have a Hyper-V Core server 2008 that I administer via command line and remote tools. We have now got a new backup system in place and it involves me connecting an External USB drive (G:) to backup system state files. My question is how should I safely remove the drive for its weekly offsite swap? I've tried using the devcon tool however it just says the 'removal failed with no devices removed' with no other explanation. I have noticed that there isnt a readily available x64 version of devcon and that might be the cause of the problem. (I have read of people downloading a amd64 version but I have not located it myself, if someone knows where it is please let me know). The devcon command worked on my old 2003 x86 server with the command: devcon remove *3200AVJ_EXTERNAL* I have also looked at using fsutil volume dismount g: but it doesn't seem to work as G: is still listed as a connected volume. I have checked that the volume is not in use via remote tools and the net file command. Both show no open files in the G:\ volume. This could be a decent substitute as it might be used to flush any remaining IO to the volume can anyone clarify? Thanks in advance.

  Read the article

• Will Parallel-port dongle work on USB-to-Parallel Adapter?

  - by Gary M. Mugford

  We have a niche program running on a Win2K laptop that uses a security dongle connected to a parallel port for authentication. The laptop is getting creaky and I spent a frustrating night last night shopping various websites for a new laptop that had a parallel port. Seems I'm about three years late [G]. The question I have, is, if I buy a new(ish) laptop and use a USB-to-Parallel Port adapter, will the security dongle work? I know I'm not being specific about the app, but it's one most people wouldn't have heard of anyways. I've been guessing the answer to my question is no, since the app won't know to send a request out to the non-existent port. But, if the process actually is that the dongle sends a message INTO the computer every now and then, then it might work. And, I'm not sure whether the dongle is only needed at program startup time or randomly. The dongle is a 'permanent' addition to the old laptop. This is all about the money. We can have a newly-updated version of the program (which won't add any features we need) for the princely sum of $2700. Or we can spend $500 on a refurbed laptop still running WinXP, add a 30 buck adapter and keep the same solid, stolid performance we've come to appreciate. But it all comes down to the dongle behaviour. Oh, and a dock won't work. The whole laptop issue is about moving about the various nooks and crannies of the building with laptop in hand. Thanks for any suggestions/guidance. GM

  Read the article

• How do I remove a USB drive's write protection?

  - by nate

  I have a SanDisk Cruser Blade USB stick that suddenly seems to be write protected. I tried running DiskPart but after I write the command "attributes disk clear readonly" it displays this: Microsoft DiskPart version 5.1.3565 ADD - Add a mirror to a simple volume. ACTIVE - Marks the current basic partition as an active boot partition. ASSIGN - Assign a drive letter or mount point to the selected volume. BREAK - Break a mirror set. CLEAN - Clear the configuration information, or all information, off the disk. CONVERT - Converts between different disk formats. CREATE - Create a volume or partition. DELETE - Delete an object. DETAIL - Provide details about an object. EXIT - Exit DiskPart EXTEND - Extend a volume. HELP - Prints a list of commands. IMPORT - Imports a disk group. LIST - Prints out a list of objects. INACTIVE - Marks the current basic partition as an inactive partition. ONLINE - Online a disk that is currently marked as offline. REM - Does nothing. Used to comment scripts. REMOVE - Remove a drive letter or mount point assignment. REPAIR - Repair a RAID-5 volume. RESCAN - Rescan the computer looking for disks and volumes. RETAIN - Place a retainer partition under a simple volume. SELECT - Move the focus to an object. It's like when you type help at the DiskPart prompt, so how do I get past this? This problem started when I plugged the stick into a laptop which had viruses, if that's any help.

  Read the article

• Grub hangs at "Starting up ..." when USB flash card reader is plugged in (on Ubuntu Hardy)

  - by Laurence Gonsalves

  I have a PC with Ubuntu Hardy installed. The machine boots fine unless my USB flash card reader (one of those N-in-1 readers by MediaGear) is plugged in at startup. If the reader is plugged in, the boot process proceeds as normal until it gets to the screen that says "Starting up ...". At that point it just hangs forever. To work around this I currently leave the reader unplugged when booting, and then plug it back in after I see that Ubuntu is actually starting. This is annoying though, especially when I reboot the machine (typically for updates), forget to unplug the reader, and walk away only to come back hours later to find the machine hung. My guess is that the presence of the reader is confusing Grub about where to find the kernel. The weird thing is that Grub is on the same drive as the kernel I want it to boot so clearly the drive is still readable even when the flash card reader is plugged in. Is there some way I can tell Grub to never go looking on the flash card reader?

  Read the article

• Does anyone know where I could find a 2 input USB voltage meter?

  - by John O

  What we really need is a tiny UPS, of sorts. We'll be hooking up a solar cell and a battery to a single board computer. Currently, that SBC is a custom Pic32 device, and it does it's own UPS and voltage monitoring duties. I've been tasked with trying to replicate all of its features with off the shelf products... and for the most part I've succeeded. But I don't currently have any way to switch between two sources of juice, or monitor when they're getting low. These guys have something: http://www.mini-box.com/picoUPS-100-12V-DC-micro-UPS-system-battery-backup-system I really like it, the price is well within the budget. We might even work it in though it does 12V and I'll probably be using 5V... there are enough engineers on hand to figure out something. But I'd still have no idea what the voltage was for the PV or battery. I was hoping that there was some simple little USB multimeter thing that I could use to monitor this with, but I can't seem to come up with anything. I've found all sorts of cool hardware, but nothing that will help us. Does anyone know of anything?

  Read the article

• Gparted resize of an extended partition fails with error "can't have overlapping partitions".

  - by Marcus

  I just decided to install Ubuntu 12.04 alongside Windows 7 on my Dell laptop. However I didn't do this manually but instead used the "Install Ubuntu alongside Windows 7" option during the installation. Now the partition that Ubuntu runs in has very little space and I am getting warning messages. I'm trying to use gparted 0.12.1-5 (via a live CD) to give Windows less space and give Ubuntu more. I've managed to remove 100GB from the Windows partition so I now have some unallocated space between Windows and Ubuntu. This is what it looks like inside Ubuntu (not using the live CD, since it won't let me mount a USB to save a screenshot): So first I take sda4 (extended?) and resize it to the left so it takes up all the unallocated space. Then I resize sda5 (ext4) as well so it takes up all the new space. However, when I hit apply, it fails on the first action (resizing sd4) with the error message can't have overlapping partitions. Any ideas as to why this happens? I also tried resizing sda4 by just a few MB so that it definitely didn't overlap anything, but I still got the same error message. To clarify, I am using gparted from the LiveCD, I just took the screenshot from Ubuntu. I couldn't attach the details file containing the error information from gparted because I can't mount a USB drive when I'm running from the LiveCD. I'm tried following the guide on the gparted website but it says Invalid argument or something like that. If the gparted details are needed, I may need some hints on how to solve the USB issue as well. :)

  Read the article

• Resizing partition using Gparted gives "can't have overlapping partitions" error

  - by Marcus

  I just decided to install Ubuntu 12.04 alongside Windows 7 on my Dell laptop. However I didn't do this manually but instead used the "Run Ubuntu alongside Windows 7" option upon installation, and now the partition that Ubuntu runs on has very little space (It's giving me warnings). I'm trying to use Gparted 0.12.1-5 (via a live CD) to give Windows less space and give Ubuntu more. I've managed to remove 100GB from the Windows partition so I now have some unallocated space between Windows and Ubuntu. This is what it looks like inside Ubuntu (not using the live CD, since it won't let me mount a USB to save a screenshot): http://i.stack.imgur.com/0keQq.png So first I take sda4 (extended?) and resize it to the left so it takes up all the unallocated space. Then I resize sda5 (ext4) as well so it takes up all the new space. However, when I hit apply, it fails on the first action (resizing sd4), saying "can't have overlapping partitions". Any ideas as to why this happens? I also tried resizing sda4 by just a few MB so that it definitely didn't overlap anything, but I still got the same error message. To clarify, I am doing it using the CD, I just took the screenshot from Ubuntu. Any help would be greatly appreciated! And again, I can't mount any USB (I'm following the guide on the gparted website but it says "Invalid argument" or something like that) so I couldn't attach the details file from Gparted. If this is needed, I may need some hints on how to solve the USB issue as well. :) Thanks

  Read the article

< Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >