Search Results

Search found 16808 results on 673 pages for 'computer guru'.

Page 605/673 | < Previous Page | 601 602 603 604 605 606 607 608 609 610 611 612  | Next Page >

• Router(s) Issue: DNS quries sporadically fail with multiple computers hooked in

  - by bob-the-destroyer

  Basically, after anywhere from 5-60 minutes, DNS queries fail for a few minutes, then slowly begin to resolve correctly. Then the cycle repeats. This occurs only when more than one computer is on the network. All computers on the network experiences the same sporadic DNS outage at the same time. Wireless or wired, Linux or Windows, fresh OS install or old, browser or ping, same symptoms. Duplicated on 3 routers (not chained together, mind you) and 3 ISP's and 3 separate locations over the past several months. The only common theme is a single 5-yo WIN XP laptop which has been in use on the network throughout all this. There also may be anywhere between 1 - 10 devices hooked up wired or wirelessly at a time. The only reprieve I have from this torture is by using any VPN to an outside source - always smooth sailing. I typically set up any router to a) use WPA2/etc security; b) MAC whitelist; c) UPNP OFF (if available); d) always update firmware when available; e) obtain DNS from ISP automatically; f) set the router to act as DHCP server for the internal network. Adjusting channels has no effect. Any ideas?

  Read the article

• Windows 7 not booting after failed SRT (SSD caching) install

  - by david

  This is a fairly new computer, only about a month old. i7 2700k, z68 motherboard, with a 1.5tb WD black HD, and a 128gb crucial M4 ssd. I followed the instructions for setting up ssd caching, the SATA controller was set to RAID, I installed the intel software and enabled acceleration and it said everything went fine. But when I went to reboot, I received the lovely "Reboot and Select proper Boot device" error message. I checked the bios, and it was booting from the correct HD (I tried the only other option anyway just in case, it was the ~50 odd gb of unformatted space left on the SSD) AFter that I entered the raid until (ctrl-i at boot) and removed the acceleration and deleted the raid array (because it was being used as a cache this was non destructive) Still no boot. So I reinstalled win7 directly on the SSD, booted, and checked the HDD to make sure it hadn't been wiped. It hadn't, all the files were still there, including all the windows stuff. I backed up my data to an external drive just in case, but I'd really like to get this install booting again. I trawled the webs a bit, and have tried entering recovery mode and using the bootrec.exe and bootsect.exe to fix it, but to be honest I'm not sure what I'm doing with those. My question is basically: How do I make my harddrive bootable again?

  Read the article

• Hiding my location to websites with region-specific languages/content

  - by Tudor

  I just went to download Microsoft Secority Essentials and it enraged me as it redirected me to a site in my home language and not the default English. If I go to America, I don't want them to speak Swahili. It reminded me of all the other websites who try to do the same. I don't want my content in greek when I'm on vacation! I for one simply can't work on a computer unless the language is English (or unless there's a VERY good reason to change the language). Location aware content is only good for download mirrors, and even then I would rather pick from a list of countries myself. (or if you can't speak anything but your own language) I know websites get your location from your IP and ISP, but is there any way you can inhibit this behaviour on a browser level? Is there any Chrome/Firefox extension for it? Do I really have no choice but to hide my IP? There's all sorts of services that claim they're hiding your IP for free so that people can't log and trace your steps through the internet, but they're probably logging it themselves and making money off it. Why else would they be free? I've found that Firefox has an Option that says "Choose your preferred language when displaying pages". Haven't found anything for Chrome.

  Read the article

• Apache: Setting up local test server with subdomains

  - by RC

  Hi everyone, I have XAMPP running on my desktop machine, and I do all my work on it with no issue. http://localhost ---> points to public_html http://site1.localhost ---> points to site 1 http://site2.localhost ---> points to site 2 http://site3.localhost ---> points to site 3 Entering the above URLs in my web browser on the machine with Apache works great, and I can work on multiple sites within distinct subdomains. But what I want to do now is to transfer Apache and all the files to another Windows 7 machine within the LAN, but still be able to view the subdomains from my main development machine. With a vanilla XAMPP installation on the new hosting machine, entering the IP address of that machine (e.g. 192.168.1.10) into my development computer would send me to the main public_html folder. But how do I set up subdomains such that I can access it externally? For example, http://site1.devmachine Thanks for any help.

  Read the article

• Windows 7 explorer crashing trying to read external hard disk

  - by Mario De Schaepmeester

  I have a 1TB Western Digital hard drive which is almost full and last time I tried to plug it into my laptop, I got a Windows dialog saying "this hard drive needs to be formatted". I did not panic because I have experienced things like this before and I know it's often solved by simply re-inserting the drive. Now however, whenever I plug it in and try to browse it in explorer by going to "computer", the explorer process crashes after a while. I simply close explorer since it takes ages trying to read the disk and nothing happens. After searching on the internet, the best thing to do would be a chkdsk. I tried it via properties in explorer (which also took a good 5 minutes to open up), locks up as well, after waiting a couple of minutes it says there's no access to the disk so a chkdsk is not possible... I want to make clear that I always use safe removal before pulling out the USB cable. Last time however, safe removal just would not work and when trying to shut down Windows, the logoff screen just would not disappear (I've waited at least 10 minutes or so) and I powered off the PC by force. This may be the cause of the problems but the disk was still recognised immediately after that. I really don't want to format this thing because it contains C: clones of 3 computers and a lot of other stuff that I don't want to re-copy. What would be the best course of action? Update I got chkdsk working via the command line. I used the /F and /R options. I already got a bunch of lines saying "file record segment X is unreadable" or whatever it is in English, my OS is Dutch. It looks bad... Will chdsk repair these errors?

  Read the article

• How to copy VirtualBox VDI contents to a partition and dual boot the OS from it?

  - by Calmarius

  I'm a Linux user but I keep a compressed Windows XP ISO with me on a pen drive for the case I absolutely need Windows to do something. This works in VirtualBox most of the time. But now I want to play some games, so I would like to run the Windows image natively. My computer don't have CD drive so cannot just burn the ISO and make an install normally. What I trying to do is moving the installed Windows image to a physical NTFS partition on my HDD and set up GRUB to let me dual boot it. I found many tutorials that deal with making VDI to physical drive. But they assume I want to overwrite my entire drive. Moving the raw disk image with dd to the partition resulted in a corrupt partition. I also tried the VMDK trick to use that empty partition and install the Windows on it. Although the text mode phase of the installation finishes without problems, the VM won't work, either crashes and keeps rebooting or just immediately or freezes (depending on how I created the VMDK, with -rawdisk /dev/sda3 or -rawdisk /dev/sda -partition 3).

  Read the article

• Svchost.exe connecting to different IPs with remote port 445

  - by Coll911

  Im using Windows XP Professional SP2. Whenever I start my Windows, svchost.exe starts connecting to all the possible IPs on LAN like from 192.168.1.2 to 192.168.1.200. The local port ranges from 1000-1099 and the remote port being 445. After it's done with the local IPs, it starts connecting to other random IPs. I tried blocking connections to the port 445 using the local security polices but it didn't work. Is there any possible way I could prevent svchost from connecting to these IPs without involving any firewall installed? My PC slows down due to the load. I scanned my PC with MalwareBytes and found out it was infected with a worm, it's deleted now but still svchost is connecting to the IPs. I also found out that in my Windows Firewall settings, under Internet Control Message Protocol (ICMP), there's a tick on "allow incoming echo request" (usually disabled) which is locked and I can't disable it. Its description is as follows Messages sent to this computer will be repeated back to the sender. This is used for trouble shooting for e.g to ping a machine. Requests of this type are automatically allowed if TCP port 445 is enabled. Any solutions? I can't bear going with the reinstalling Windows phase again.

  Read the article

• How do I fully share a Hard Drive on my Local Network?

  - by GingerLee

  I have 4 computers connected to a router (DD-WRT) My main PC is Windows 7 (Home Premium). This machine has 2 Hard Disks: HD1 is used for my OS and the other (HD2) is used to store files. My 3 other machines are 1. Ubuntu Destop that I use to learn about linux, 2. A Mac OSX laptop, and 3. A netbook running windows 7. How do I easily share HD2 with my other machines? I would like all my machines to have full access & permissions to HD2 however I would like to RESTRICT access to only PCs that are connected to my router (either via LAN and WiFi) --- btw, I know this is not very secure due to WiFi vulnerability , however, I currently MAC address restrict WiFi connections my router. Extra Info: I have already tried to use the Windows Folder Sharing feature: i.e. I right click over the icon of HD2, and click on the Sharing Tab, but in sub-window labeled "Network File and Folder Sharing", the "Share" button is grayed out. I can click on "Advanced Shared" but that just takes me to a screen in which I have to set certain permissions. What is not clear to me is: How do I set a criteria that shares HD2 with all computer connected to my router?

  Read the article

• Our clients site is redirecting to a pill scammy site [closed]

  - by Alex Demchak

  Possible Duplicate: My server's been hacked EMERGENCY We've usually host our clients site, but we aren't hosting this one. The website itself (weddle-funeral.com) works just fine. if you load google and search for weddle funeral stayton oregon - and click that link, the site links to a scammy pill site. I went through the site and there were some php files in the wordpress plugins that got quarantined by my antivirus. I removed ALL non essential files, and uploaded fresh versions of all the plugins, but it's STILL redirecting from google. I tried logging in to the cpanel (on a virtual private server), and the cpanel flashed a red warning screen The site's security certificate is not trusted! You attempted to reach XXXXX.com, but the server presented a certificate issued by an entity that is not trusted by your computer's operating system. This may mean that the server has generated its own security credentials, which Google Chrome cannot rely on for identity information, or an attacker may be trying to intercept your communications. You should not proceed, especially if you have never seen this warning before for this site. (Keep in mind, that's for the HOSTING accounts CPanel) Is there something in the SERVER probably that's causing the redirect? EDIT: .htaccess file contents # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteRule ^index\.php$ - [L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> # END WordPress

  Read the article

• How to make Microsoft JVM work on Windows 7?

  - by rics

  I am struggling with the following problem. I cannot install MS JVM 3810 properly on Windows 7. When I start Interner Explorer 8 without starting any java 1.1 programs choosing Java custom settings under Internet options causes the crash of the browser. I have some Java 1.1 programs that work well in Internet Explorer 8 on Windows XP after the installation of MS JVM 3810. I know that it is not advised to use this old JVM but it is not a short-term option to port the programs in newer Java since it contains 3rd party components. Complete rewrite is a long-term plan. Strangely jview and appletviewer (jview /a) works from a console so the MS JVM 3810 is not completely busted just IE 8 does not like it. The problem with the appletviewer is that it cannot connect to the server even if both signed and unsigned content in Java custom settings have been set to Enable all. (Since Java custom settings was unreachable due to the crash the modifications - including My computer - were performed through the registry and pre-checked to behave correctly on Windows XP and Internet Explorer 8.) If jview was working then I could at least think of a workaround. Is there a way to configure MS JVM or jview properly on Windows 7? Another options would be: Checking Internet Explorer 9 Beta. Using virtualbox and Windows XP older IE in it. Delaying Windows 7 upgrade. ... Update Finally we have modified all the programs to work parallelly as applet and application as well. This way the programs can still be used from browser on older Windows versions. On Windows 7 the applications are started from the desktop. Installation to all user machine can easily be solved since they already have a large common application drive. The code update is fortunately only a few lines of modification: including a main method in the applet class. Furthermore instead of the starting html page a bat file is used to set the classpath before the startup with jview.

  Read the article

• 3-4 old computers = general purpose cluster?

  - by TheLQ

  I have 3 old computers lying around right now running a P2 at 800 MHz(?), Intel Mobile 1.6 GHz, AMD Athlon XP 2000+ at 1.66 GHz, and (might not use this) P4 at 2.7 GHz, all with 512 MB Ram, and am considering clustering them together for fun/knowledge. They would be running an undecided version of linux, preferably ubuntu based. The issue is what I want to use it for: general computing and occasional video encoding. By general computing I mean day to day tasks. However I'm not sure if every program started by a single X session is going to exist on the same machine, defeating the purpose of such a system. Will programs be split up or exist on one machine? Second, assuming this is running 100baseT ethernet (not sure if the PCI slot itself could handle Gigabit), would the speed of having a program exist over the network be an issue? It seems that the constant asking of various things in RAM would be quite slow. And before you say "buy another computer!", that's not the point of this question. I'm asking would it be usable, not necessarily practical. And yes I know, this is going to be extreamly power consuming.

  Read the article

• Bootable ISO to USB stick xp quickest method

  - by brux

  My dog took a leak on my PC when I went out (ye funny), now it reandomly restarts - I'm convinced the HDD is failing because the Windows seagate diagnostic program fails on a few tests. I want to run this prior to windows in an attempt to try and recover sectors, the program includes an iso which can be written to cd and booted, but i dont have any cd's. I tried using unetbootin to create the bootable usb from the iso file (SeaToolsDOS222ALL.576.ISO) but it doesnt work. When i boot from the usb hdd unetbootin loads with "default" in the menu. No joy booting though. I checked the usb hdd in windows and all the files are there, extracted from the iso file, wont boot though. Any ideas? Im using windows xp. More info - when the computer restarts (like i just did now) it constantly reaches the end of POST and then restarts in infinite loop. If I pull the power cable out it will get back into windows, the longer i leave it between attempts, the longer I am able to stay in windows until it restarts. i.e if i leave the power cable out 5 minutes it will stay operable for longer than if i had left it out for only a few seconds.

  Read the article

• Need to set up a proxy on Linksys E3200 to filter home internet

  - by Justin Amberson

  the fact that I have a Linksys E3200 may not be important. I can configure the router through the web interface, but I don't know the things I will be toggling are called. I already do simple port forwarding to access applications on my Mac remotely. So router admin is not something I technically need explained. I'm looking to running a proxy on my home computer, that filters all HTTP traffic that goes through my router. So if my daughter is on her iPad and accesses Safari, my Mac will be the judge of the validity of the request. I need something like NetNanny I guess, but local. Actually, anything that can just filter all port 80 traffic that runs locally, but maybe validates with a password? I truly truly hope this question falls within the bounds of Serverfault. I'm not a total internet newb but I'm at a loss for what to Google. If possible answer this question: Is there a webapp that can listen on port 80, and validate requests to port 80 with a password? If so, can I forward all traffic on port 80 to my Mac, to be re-routed to the user? Is this the same as a VPN? Thank you for your help. Justin

  Read the article

• Tried to install Mint to a Flash Drive. Now I can't boot from the main hard disk.

  - by Dan

  Hello, all. I'm kind of new to Linux and I need some help. I wanted to install a Linux distro to a flash drive so that I can have a portable OS with all my settings, programs, etc. wherever I go. So I fired up a Linux Mint Live CD and installed Mint to the flash drive, and this seems to work OK. But now, whenever I try to boot up my system normally without the flash drive plugged in, it doesn't seem to work. It basically hangs for a bit, and then I get the following prompt: error: no such device: (some long hex val) grub rescue> However, when I try powering my system up when the USB is plugged into the computer, it gives me an option between using the OS installed on my USB and the OS installed on my HD. Selecting the latter, everything loads up just fine. I'm guessing that installing Mint to the flash drive somehow messed with my native Grub installation, but, again, I'm kind of new to Linux, so I'm not sure exactly why. Any help is greatly appreciated.

  Read the article

• retain last used path to location for saving files in Windows 7

  - by Mark Miller

  I am using Microsoft Office 2010 and Windows 7 on a Dell PC. I am opening a bunch of MSWord files one at a time, copying data tables therein, pasting the data into Excel and saving the Excel files as comma delimited text files. I am creating a separate Excel file for each MSWord file. The path to the folder containing the saved comma-delimited files is quite long, something like this: c:\users\me\aa\bb\cc\dd\ee\ Every time I open Excel and save a new comma-delimited file I have to re-navigate the entire path (c:\users\me\aa\bb\cc\dd\ee). In the past Windows seemed to remember the last used path, saving a lot of tedious key-strokes. In fact, I think Windows did this for me as recently as last week, albeit on a different computer. Can I apply a setting in Windows somewhere asking it to offer the last used path as a default when saving files so I do not have to re-navigate the entire directory structure to save each new comma-delimited file? If I can, how so? Where is the option for specifying that setting? Thank you for any help.

  Read the article

• Anyone have a script to delete a specific local windows profile?

  - by Jordan Weinstein

  I'm looking for Powershell (preferred) script, or .CMD or .VBS, to delete a specific user profile on a workstation (WinXP) or terminal server (2000, '03 or '08). I know all about the delprof utility... That only allows you delete based on a period of inactivity. I want a script to: prompt admin for a username delete that username's profile and to delete the entire profile - registry hive too (not just the folder structure within Documents and Settings). The same way it would if you went to My Computer Properties Advanced tab User Profiles Settings and deleted profiles from there. Any ideas? All I can think of is doing an AD lookup to get the SID of the user specified, then using that to delete the correct registry hive too... something simpler would be nice though... Basically, my HelpDesk used to be local administrators on our Citrix servers and a common fix for various issues was for them to delete a user's profile on the citrix server(s) and have that user log back in - voila, whatever issue they had was resolved. Going forward, in new Citrix environment, they will no longer be local admins on those boxes, but still need to be able to delete profiles (deleting the entire profile: folder and reg hive is key). thanks.

  Read the article

• Outlook 2010 search not working after upgrade to windows 8

  - by Klaaz

  After upgrading my computer to Windows 8 Outlook 2010 has stopped displaying search results. Normally you can enter a (part) of a word in the search box on top of the inbox list and it will show you result immediatly. Even mails allready visible on the screen are not found. Somebody familiar with this issue? Update: maybe relevant: I use an Google Apps Pro account. All mail is synced and locally available in Outlook 2010. I did not change this in any way while upgrading, it was working perfectly before. I can scroll through all the e-mails, new mails are coming in as expected. This morning I received two mails from a person by the name of Rosanne. When searching on her name in Outlook it gives me One (1) result, the last mail from today. Update 2: Rebuilding the index seemed to be working. But after another day it stopped working again. No results whatsoever in Outlook search. Rebuilding indexes every day is not an option as it takes several hours. I suspect it has something to do with the fact that I use Google Apps Pro. It acts like a Exchange server to outlook. In indexing options (configuration) I added the directories containg the PST from this service (mail is also synced locally)

  Read the article

• Run as another user, but also as administrator

  - by Tewr

  I am trying to debug a virtual machine (VM) running on a remote computer from my workstation (A). Both VM and A are running Windows 7 Enterprise. Apparently, I need to start the Remote Debugger Service (RDS) on VM as an administrator. Apparently, I also need to run RDS as the user Tewr logged in on A (domain: DOM). VM runs the services i need to debug, as well as the remote desktop interface with an account VMUSER in a domain called VMDOMAIN. I manage to start RDS as administrator, but then the RDS process is owned by VMUSER and that's not good enough. I also manage to run RDS as DOM\Tewr, but then not as an administrator. I have Added DOM\Tewr as an administrator on VM, but thats not good enough becuase the process is still not run as administrator. How can I run the RDS process as DOM\Tewr and "As Administrator", while logged on in windows as VMDOMAIN\VM? (note: I have tried creating an account with the same credentials / password as VMUSER, as hinted in the ms article above, but with no luck...)

  Read the article

• Workaround for Dell "Power Supply Not Recognised" issue

  - by Haedrian

  So, I have a Dell Inspirion and the power supply port appears to be damaged. Basically when I plug it in I get a nice popup telling me that it couldn't detect that its a Dell power supply so it won't charge the battery and underclocks the system. It still works for other purposes (that is, giving power) I thought it was the actual power supply cable so I bought a new one, that worked for a while, provided I inserted it at JUST THE RIGHT angle. But now that's not working anymore, so I assume its the part which connects to the computer. The battery charging I can live without, the underclocking I can't. I'd like a way around this issue. Things I've tried: Updating the BIOS Replacing the power supply cable Inserting it at different angles Turning it off and on again Swearing at it Twisting it while inserting it So, is there a workaround somehow? I'd like to avoid taking out my soldering kit and risking permanently damaging expensive equipment if that's allright. I'm hoping for a software solution. Added: The exact model is a Del Inspirion N5010

  Read the article

• Postfix not delivering from external senders and not logging anything

  - by simendsjo

  Some semi-recent upgrades must have broken my postfix+dovecot configuration, but I'm having problems finding out what the cause is. My domain is simendsjo.me with the MX record mail.simendsjo.me. I can send mail to both local and external recipients, and it delivers mail from internal mailboxes. The problem is that mail from external senders isn't delivered, and nothing is logged at all. The external sender also doesn't receive any errors. I have no idea where to ever start looking as nothing is logged at all when external mail is sent to my server. So the first issue would be: How can I turn on some debug messages for postfix? I've tried: debug_peer_level = 2 debug_peer_list = simendsjo.me .. And _level = 999 and _list = gmail.com where I'm trying to send emails from. but nothing is logged. When sending mails from a local mailbox (but from an outside computer, not localhost), a lot is logged. I don't have any rules in iptables either. Any ideas how I can get some debug messages for postfix?

  Read the article

• My scanner isn't responding. It is connected to a SCSI interface using Windows XP

  - by Bob

  I have a Microtek ScanMaker 9600XL scanner. The best part about it is that it is 12x17 inches. Wowza! The worst part about it is that I've had it working at one point, with the same cable, same card, same computer, but have since re-installed Windows XP on it. Currently it will turn on, and blink the Power and Ready lights. They should be solid. I've done my best to find documentation for this, but all I've really gotten is the content on the Microtek site. I've tried turning the scanner on, then the PC. Turning the PC on, then the scanner. When I try launching the software it pops up a dialog saying "ScanWizard Pro can't find any scanners! Use SCSI Check to find a scanner." I know the scanner has a pair of little buttons on the back. These cycle up/down a counter. I think it goes 0-7. Any thoughts on what that does, or how to proceed troubleshooting? I think my next step is to try each of those numbers, and do both pc booted first, and scanner booted first for each of those numbers...

  Read the article

• Connecting to network device behind NAT from local LAN using the external port and IP

  - by lumbric

  I noticed at several different LANs connected to the Internet through a NAT the following phenomena. There is a server in the LAN and there is a port forwarding to reach this server also from outside the LAN through the NAT. E.g. consider a LAN with the address 192.168.0.* and a SSH server at 192.168.0.2 with port 22 and a forwarding from port 2222 at the NAT 192.168.0.1 to 192.168.0.2:22. If the NAT's external IP is 44.33.22.11, one can connect to the SSH server through 44.33.22.11:2222. Surprisingly this works only from outside the LAN. If one tries to connect to 44.33.22.11:2222 from behind the NAT, there is no answer. Of course one could simply use 192.168.0.2:22, but often it is simpler to use the external IP. The typical use case for me is the configuration on a laptop computer. Usually the user uses any arbitrary Internet connection to connect to his home or office server, but sometimes he will use also the LAN to connect to it and it would be annoying to have to different configurations or bookmarks. Why does it fail to connect from inside the LAN? Is there any good work around?

  Read the article

• Does image block (firefox addon) save internet bandwidth usage?

  - by dkjain

  Does image block save internet bandwidth usage. I have a data capped plan from my ISP ( 5GB at 2mbps and thereafter 256 kpbs / pm). I doubt if the addon or other similar addon actually saves bandwidht. Here is my point of view, pls correct if that is wrong. When a request is sent to the server, the server sends out whatever page it's requested to serve with all its text and images etc. So essentially my ISP has made his pipe available for the data to reach me thus he would count those bytes under my data plan. When the data arrives it's all first stored to my browser cache (folder) area which means all the data has actually been received by me/computer using my ISP's pipe. The browser then fetches those data from the cache and displays it. By hitting the stop button or blocking images via ur addon I am just choosing not to display the data which would remain in the cache or eventually be discarded if still on the network pipe after a timeout limit. The point is the data request have been completed by the ISP and so the data would be metered and thus using addon such as image block or hitting stop button while page is loading does not in any way save internet bandwidth. Your comments plz....... Regards dk.

  Read the article

• Group Policy - Published software not upgrading

  - by VokinLoksar

  I'm testing this with mercurial MSIs, but it's the same for other packages. I've created a new group policy and added an old version of mercurial to User software installation as a Published package. On a Windows 7 client I install the package through Programs and Features. The installation works fine. Now, I would like to publish an updated version of mercurial. I create a new Published package. Under 'Upgrades' I configure it to replace (upgrade also doesn't work) the old version and mark this upgrade as 'Required'. The old package is not removed. The Windows 7 client is then restarted. When I log back in, I see a status message saying something like 'Removing managed software Mercurial ...'. There is no message about installation of the upgrade. If I look in Programs and Features, I can see the new version of mercurial listed. However, the actual mercurial directory under Program Files is missing. It's as though the installation recorded information about the MSI, but didn't actually install anything after removing the old version. As I mentioned, this isn't specific to mercurial. I've tried using other apps and have yet to find one that can be upgraded via a Published package. Using Assigned packages in Computer Configuration works without problems, but I would like this software to be optional rather than required. Ideas?

  Read the article

• Windows XP Freezes

  - by Jim Fell

  Hello. I'm running a machine with Windows XP Professional 64-bit. Every so often, it will freeze for no apparent reason. That is, everything stops responding, except the mouse. I can move the mouse around, but I can't click on anything. Keyboard input is also not accepted/received when this problem occurs. The three-finger salute fails to bring up the Task Manager. Even pressing the power button on my computer fails to shut it down. The only way out of this that I have found is to hard-reboot the machine (i.e. pull power or hold power button in for 10 seconds). This problem was occurring on the system when it had all its updates and after a fresh install when not everthing was quite yet updated. I've run the Scandisk utility and the latest version Memtest86 that supports 64-bit architecture; neither found any errors. The last time this happened was on a fresh install of Windows. Only Nero Essentials, Avast antivirus (disabled), Firefox, and Spybot were installed. I was not running Nero, Firefox, or Spybot at the time, and Avast was disabled, so I'm pretty certain this is a Windows issue. Is anybody familiar with this problem or have any pointers? Thanks.

  Read the article

< Previous Page | 601 602 603 604 605 606 607 608 609 610 611 612  | Next Page >