Search Results

Search found 30511 results on 1221 pages for 'linux networking'.

Page 61/1221 | < Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >

• [CentOS 4.8] nslookup resolves domains to IPs, but I can't get a response to pings to external servers

  - by Beco

  I have a fresh install of CentOS 4.8 running on an internal development server. I haven't done anything to it besides setting up sudoers and SSH. I can SSH into the server and from there resolve domains to IPs and ping internal servers, but for some reason I don't get any response from pinging external servers. The software firewall is disabled, and the problem is present with both static and DHCP-assigned network configurations. The network domain controller is a Windows Server 2003 box. $ nslookup google.com Server: 10.254.2.5 Address: 10.254.2.5#53 Non-authoritative answer: Name: google.com Address: 74.125.47.147 Name: google.com Address: 74.125.47.99 <etc...> 10.254.2.5 is the Win2K3 server. $ ping google.com PING google.com (74.125.47.106) 56(84) bytes of data. It just hangs here indefinitely. $ cat /etc/resolv.conf ; generated by /sbin/dhclient-script search <...snip...>.local nameserver 10.254.2.5 nameserver 10.254.2.124 10.254.2.124 is the backup DC server, which is currently off and tombstoned by this point. The snipped section is our company name. # ifconfig eth0 Link encap:Ethernet HWaddr <snip> inet addr:10.254.2.101 Bcast:10.254.2.255 Mask:255.255.255.0 inet6 addr: <snip>/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:80066 errors:0 dropped:0 overruns:0 frame:0 TX packets:4421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7810133 (7.4 MiB) TX bytes:590550 (576.7 KiB) Interrupt:225 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:32 errors:0 dropped:0 overruns:0 frame:0 TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8104 (7.9 KiB) TX bytes:8104 (7.9 KiB) # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.254.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.254.2.5 0.0.0.0 UG 0 0 0 eth0 And, for good measure, a snapshot of the current ethernet config via the system-config-network GUI. Edit: I don't yet have enough rep to post images, so here's a link. Sorry! system-config-network snapshot I'm pretty green when it comes to setting up *nix dev servers and network configuration in general, so please let me know if I've left out critical information, or posted information I shouldn't have posted. Thanks!

  Read the article

• What's the best way to forward traffic on a specific port to another machine?

  - by Ankit

  The setup I have is this: [client01] <-A-> [server01] <-B-> [server02] client01 can access port 9300 on server01 (connection A). server01 can access port 9300 on server02 (connection B). What's the best way to make all traffic on port 9300 to server01 go to port 9300 on server02? I can successfully do this with an ssh tunnel from client01 to server01 to server02, but I don't want to have to run ssh on client01. When I ssh from server01 to server02 forwarding port 9300 (ssh -g -L9300:localhost:9300 server02 on server01), it doesn't work -- am I using the wrong command?

  Read the article

• How iptables behaves on timezone change?

  - by pradipta

  I have doubt how iptables keep changing the info in iptables when timezone is change. I am using iptables s v 1.4.8 I have blocked one IP with following details # date Thu Jun 6 12:46:42 IST 2013 #iptables -A INPUT -s 10.0.3.128 -m time --datestart 2013-6-6T12:0:00 --datestop 2013-6-6T13:0:00 -j DROP # iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination DROP all -- 10.0.3.128 anywhere TIME starting from 2013-06-06 12:00:00 until date 2013-06-06 13:00:00 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination But after I change the timezone following things happened automatically . AFTER TIME ZONE CHANGE +++++++++++++++++++++++ #date Thu Jun 6 15:17:48 HKT 2013 # iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination DROP all -- 10.0.3.128 anywhere TIME starting from 2013-06-06 14:30:00 until date 2013-06-06 15:30:00 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # The time value is changed in the rule . It is changing with the timezone how. Where iptables keeps track of timezone. Kindly explain me.

  Read the article

• Fedora 17 transparent Ethernet Bridge not forwarding IP traffic

  - by mcdoomington

  I am running on Fedora 17 with the latest ebtables and have been trying to setup a transparent bridge - using the following script, I send a ping through the bridged host and only see the requests on the bridge (among other traffic from eth0), BUT, arps and arp replies are making it through. My host is setup - Client 192.168.1.10 <-- eth0 -- eth2 192.168.1.20 Ethernet script: #!/bin/sh brctl addbr br0; brctl stp br0 on; brctl addif br0 eth0; brctl addif br0 eth2; (ifdown eth0 1>/dev/null 2>&1;); (ifdown eth2 1>/dev/null 2>&1;); ifconfig eth0 0.0.0.0 up; ifconfig eth2 0.0.0.0 up; echo "1" > /proc/sys/net/ipv4/ip_forward; ebtables -P INPUT DROP ebtables -P FORWARD DROP ebtables -P OUTPUT DROP ebtables -A FORWARD -p ipv4 -j ACCEPT ebtables -A FORWARD -p arp -j ACCEPT Any assistance would be great!

  Read the article

• TCP handshake ok, then the client isn't receiving any packets from the server

  - by infgeoax

  Topology: Client ----- Intermediate Device ----- Server Client: win7 Intermediate Device: unknown Server: CentOS 5.8 The problem occurs when the client and server are trying to establish a SSL connection. It happens to one specific port, 2000. I haven't been able to replicate the problem with other port numbers. I captured packets on both client and server. After the TCP handshake, from the client's perspective, it's not receiving ACKs for its previously sent packets so it kept re-sending them. On the server side, however, it did receive those packets and sent ACK packets. The weird thing is, after the server sent those ACKs, it received a [RST, ACK] packet, from the intermediate device, for every packet it sent. What could be the cause?

  Read the article

• Configuring two subnets with two NICS. Access from a NAS to the internet

  - by archipestre

  I am having trouble configuring my NAS. I have a DSL router with WIFI (192.168.1.1) in my flatmates room. In my room I have a server with two NICS: 1) wlan0 (192.168.1.2) that connects to the DSL router via wireless 2) em1 (192.168.0.1) that connects to the NAS (192.168.0.20) with a crossover cable. I have Fedora 17 and I have enable packet forwarding. My IP configuration is as follows: WLAN0 inet 192.168.0.1 netmask 255.255.255.0 broadcast 192.168.0.255 EM1 inet 192.168.1.2 netmask 255.255.255.0 broadcast 192.168.1.255 My routing table looks like: Destination Gateway G enmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 wlan0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 em1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0 I have enable a static route in the DSL server: Status Network Destination Subnet Mask Interface Gateway Remove Edit Active 192.168.0.0 255.255.255.0 LAN 192.168.1.2 From my server I can ping the DSL router and the NAS. From the NAS I can ping both NICS of the server. However the NAS is unable to ping the DSL router or any address in the Internet. Any idea of what is wrong. Thank you in advance

  Read the article

• Server seems up, but accepts no connections whatsoever

  - by Rnatau

  Hi, I have a problem with a Debian based Server, unfortunately housed in a remote location. Two days ago, it was suddenly down and completely unreachable. After having someone reboot it, it worked for about a day, then seemed to be down again. This time, however, it was different: -The server reacts to pings -It is scannable, and all the relevant ports are open But: -Open shells were immediately blocked, and no warning had been shown -It's not possible to open any connection - the TCP/IP handshake seems to have some problems: SSH handshake As this is a private server of a small community, we don't have the resources to pay a technician to fix the problem for us, so any hints how to fix the problem after the next reboot would be highly appreciated... Thanks a lot!

  Read the article

• Cannot open /dev/rfcomm1 : Host is down

  - by srj0408

  I am working on raspberry PI and on Bluetooth. I am using old raspberry pi kernel as the new one has got some bugs that were not resolved with respect to the bluez daemon. At present my kernel version is 3.6.11. I am using a USB bluetooth dongle and my sole purpose is to auto connect the bluetooth dongle when ever it is in range. For that i think i have to run a script in the backend on RPI that will keep on checking the existence of usb bluetooth dongle. I started from the very scratch. I installed bluez daemon using apt-get install bluetooth bluez utils blueman and then i used hciconfig which gives me that my bluetooth usb dongle is working fine. But when i did hcitool scan , it give me no device in range even though my Serial bluetooth Device was on. I wasn't able to find any device in vicinity. Also when i unplugged and plug the USB dongle again, i was able to scan the serial device , but when i repeat the process, i find the earlier condition of not finding any deice. I had find another useful link, but that need address of the bluetooth device that need to be connected. I want to automate this using hcitool scan, storing the output to the a file and then comparing it with already paired devices and their name. For that i need to figure out why hcitool scan is sometime working and sometime not. ? Can some one help me in figuring out why this is happening. Is there any problem on hardware side i.e Bluetooth dongle is buggy or i had some problem in bluez utils. Edit 1: While as of now, hcitool scan is giving me my remote device address but still i am getting the same issue of HOUST IS DOWN, '/dev/rfcomm1'. I am really not getting any idea of what to be done.

  Read the article

• Linux bonded Interfaces hanging periodically

  - by David

  I've several hosts that are showing problems with connectivity. When working from the command line, for example, typing is frozen for a second or so, then recovers - then it does it again. The most egregious example host would freeze (input) for 15-30 seconds, then recover and go out 5 seconds later. Switching cables didn't do anything - but removing one of the physical cables caused everything to clear up instantly (which why I think this is a network problem). Looking at the network I couldn't see any packets floating that would explain this. These ethernet interfaces (Gigabit Dell) were working normally previously, but since we moved the systems - and put them on a new set of switches - this has been a problem on multiple theoretically identically-configured hosts. The original switches were an HP Procurve 1810-24G and an HP Procurve 1800-24G connected with LLDP; the new switches are both Cisco SG 200-26, which I understand are rebranded Linksys switches. Is this caused by a problem with the switches? Is it the switch configurations? Are the Cisco switches incapable of handling this? I don't see where the configuration is located; I searched the usual /etc/sysconfig/network/devices but there's nothing in there about options (like mii polling) and nothing about the method of balancing the two. Searching scripts, I can't find anything in /etc/init.d/network either. The hosts are almost all Red Hat Enterprise Linux 5.x systems (5.6, 5.7) but some are Ubuntu Server 10.04.3 Lucid Lynx. I need help with both if it comes to that. UPDATE: We're also seeing some problems with servers on the original switches. The HP switches and the Cisco switches are also interconnected (temporarily); there is a cable run from one switch to the next. Pings on any of these hosts show about one ICMP packet out of every 5-6 getting dropped (timed out). Could there be an interaction between the two switches? Oh, and the hosts are using bonding with Balance-RR as the method.

  Read the article

• One Linux server has two timer

  - by garconcn

  The time on one of our Linux box is very weird. Whenever I call date 3 times, the 4th call will give a wrong time(usually 1 hour later). I have setup cron to sync with ntp server. We have 20+ similar servers, only this one has this problem. Any idea? Thanks. Linux 2.6.18-6-686 #1 SMP Thu Aug 20 21:56:59 UTC 2009 i686 GNU/Linux :~# date Fri Jun 11 17:00:51 PDT 2010 :~# date Fri Jun 11 17:00:52 PDT 2010 :~# date Fri Jun 11 17:00:53 PDT 2010 :~# date Fri Jun 11 18:14:12 PDT 2010 :~# date Fri Jun 11 17:00:55 PDT 2010 :~# date Fri Jun 11 17:00:56 PDT 2010 :~# date Fri Jun 11 17:00:56 PDT 2010 :~# date Fri Jun 11 18:14:15 PDT 2010 :~# date Fri Jun 11 17:00:58 PDT 2010 :~# date Fri Jun 11 17:00:58 PDT 2010 :~# date Fri Jun 11 17:00:59 PDT 2010 :~# date Fri Jun 11 18:14:18 PDT 2010 :~# date Fri Jun 11 17:01:01 PDT 2010 :~# date Fri Jun 11 17:01:01 PDT 2010 :~# date Fri Jun 11 17:01:02 PDT 2010 :~# date Fri Jun 11 18:14:21 PDT 2010 :~# date Fri Jun 11 17:01:03 PDT 2010 :~# date Fri Jun 11 17:01:04 PDT 2010 :~# date Fri Jun 11 17:01:05 PDT 2010

  Read the article

• OSX pdf-kit vs Linux poppler or pdf/x

  - by Tahnoon Pasha

  I keep reading and hearing that the reason that there is no good pdf editing software for Linux is that the libraries are not as well developed. That is why there is no equivalent for Skim or Preview in Linux. I had a look a the pdf-kit documentation and the poppler documentation and they looked very similar to my admittedly non-technical view. Could someone explain to me why the OSX libraries (eg) are so much easier to write projects like Skim in than the linux ones. I'm not sure if the same applies to OSX projects to NVAlt, but it seems to be a common theme - I'd just like to understand what is behind the thesis that OSX is easier to code these projects in, and what would be involved in changing it. (I'm not disputing the value of Okular or Evince and the like, just noting that they don't have the richness of functionality of Skim, Preview or even things like Goodreader on the Ipad).

  Read the article

• Linux & Windows Boot Up Times in Amazon Web Service and Windows Azure

  - by Adron

  I've been working with Windows Azure and Amazon Web Services EC2 for a good many months now (almost getting to the years range) and I've seen something over and over that seems troubling. With AWS & Linux I commonly get instance startup times with EC2 around the 1-3 minute range. With AWS & Windows OS on an EC2 instance it often takes 10-20 minutes. With Windows Azure Web or Service Role I often get anywhere from 6-30 minutes waiting for a role to startup. I assume of course this involves booting up a windows instance somewhere in the fabric. I know there has always been tons of FUD about windows vs. Linux, but I'd really like to know why it is that Windows 08 or 03 boots so much slower in the cloud than Linux. Any specific technical information regarding this would be greatly appreciated! Thanks.

  Read the article

• Vi on Linux: show ^M line endings for DOS-format files

  - by sss

  On Solaris, if you open a file in vi that has Windows line endings, this shows up as ^M at the end of every line. On Linux, vi is cleverer and understands the Windows file format, and does not display ^M. Is there a setting to make Linux vi behave the same as Solaris in this respect? A common problem for us is copying a shell script off a (Windows) dev box and forgetting to dos2unix it, and then being confused when it doesn't work properly. On Solaris the problem is obvious as soon as you vi the file, but not on Linux. Thanks.

  Read the article

• front end to linux std mailbox for development purposes

  - by Fabio

  I am actually a software developer, do have a fair amount of linux experience as a user though since 1997. I am normally on stackoverflow.com, please excuse me if this question isn't appropriate here. I am working on a web project. We send out emails. I work locally on a linux box. When coding I use my local mailboxes to check what's been sent. Emails sent out to valid email addresses are not arriving at my official mailbox; they might be stopped by the provider's mail servers (gmail, yahoo). Now, we are sending out HTML mails too. I need to check how they look like. Is there a GUI frontend to the standard linux BSD mailbox? Or should I install some IMAP/POP server for this? Will such server get the emails sent to username@localhost ? Thanks for any suggestion

  Read the article

• Interpreting regular expressions using find in Linux confusion

  - by PeanutsMonkey

  I am attempting to use the find command and came across an article at http://www.linux.ie/newusers/beginners-linux-guide/find.php which states The wildcard character is escaped with a slash so BASH sends a literal asterisk to the find utility as an argument instead of performing filename expansion and passing any number of files in as arguments. for the command find . -name up\*. Being new to the world of Linux I don't quite understand how the use of a backslash which is meant to escape the meta character * is interpreted and returns results as though as it is being passed to find. Does it mean if I use the -name option I have to use a backslash to pass a wildcard and if I don't use -name I don't have to use a backslash?

  Read the article

• Setting up Linux VPN Client on Mint: Never sends "Set-Link-Info" packet

  - by cabanaboy

  I have tried to set up a VPN Connection on the Linux Mint disto, but could not get it working. When I use a Windows 7 VPN client it works fine. I brought up Wireshark on both Windows and Linux machine and noticed that on the Windows machine, the client never attempted to send the "Set-Link-Info" packet whereas the Windows (working) VPN client did. Why isn't the Linux Mint client sending the "Set-Link-Info" packet. I think if it did that, then my connection would work. What am I missing?

  Read the article

• ADSL connetion (BSNL dataone) with puppy Linux

  - by Vaibhav Garg

  I have an old PC which I want to use for internet browsing. I tried using Puppy Linux (version 4.3.1) for the same but have not been able to connect. I connect via PPPoE. My network card is RTL 8029b which is automatically detected by Puppy Linux. However, the LED indicator on the MODEM designating LAN connectivity stays off. This post is being typed from the same PC running XP, so there are no connection issues. I am a complete newbie for Linux. can somebody point me to instructions. I will be willing to give any more information if required. P.S. My MODEM is Huewei Smartax MT 882 Thanks

  Read the article

• 1Tb disk formatted on Linux won't mount on windows nor mac

  - by Pedro MC

  I have an external HD (western digital) with 1Tb. I use Linux but I wanted to reserve a cross platform partition on the disk. I decided to create two partitions and used the "disks" application to do it. I created one partition with the LUKS (version 1) encryption and the other one, cross platform, in NTFS filesystem. Things work fine on my OS but when I try to use the disk (the cross platform partition) on both windows and mac the device is not recognized. What could it be? Next, output of "sfdisk -l /dev/sdb": Disk /dev/sdb: 121600 cylinders, 255 heads, 63 sectors/track Units = cylinders of 8225280 bytes, blocks of 1024 bytes, counting from 0 Device Boot Start End #cyls #blocks Id System /dev/sdb1 0+ 36473- 36473- 292968750 83 Linux /dev/sdb2 36473+ 121600- 85128- 683789062+ 83 Linux /dev/sdb3 0 - 0 0 0 Empty /dev/sdb4 0 - 0 0 0 Empty

  Read the article

• Cannot find my hard disk while installing linux-“No root file system defined” error

  - by Syam Kumar S

  I am trying install Linux on my computer (tried Ubuntu 10.4 and Linux Mint 9). I started the installation wizard and on the hard disk selection page the hard disk is not displayed. I have a 500GB disk with 5 partitions and windows 7 ultimate in one partition. If I click the forward button, it shows an error- "No root file system defined". I have tried to install by booting from CD and pendrive but both shows the same error. When I load Linux as live CD it doesn't show the hard disk. My hard disk works fine in windows 7. System config: intel i3 2100, 500GB hdd, 2GB ram

  Read the article

• How to access Guest (Linux) Filesystem from Host (Windows) in VirtualBox

  - by Dominic Barnes

  I am trying to synchronize my music between my desktop (Ubuntu 9.10) and my laptop (VirtualBox: Windows 7 host & Ubuntu 9.10 guest) I use Unison to perform the actual sync, which itself is not the problem. I am ultimately trying to get my Windows 7 host to be able to access the music files so I can sync my iPod Touch. What I need to figure out is how I can that to work. I would prefer to actually perform the sync to my Ubuntu Guest, mostly because of the filename allowed character differences between Windows and Linux. Is there a way to access the files on my Linux Guest from the Windows Host? Can I mount the VDI in Windows when VirtualBox is off? Can I have Windows Host access the Linux Guest filesystem while VirtualBox is running?

  Read the article

• Wiping out user and/or root password in embedded linux

  - by TryTryAgain

  We have a security camera system running an embedded linux. It boots with Lilo as a bootloader and has no tty access once booted. I don't know any username either. SSH/22 is open, but I don't think brute force is an option. I have tried all the common tricks to reset a linux user password (boot from the bootloader in single user mode = doesn't happen, still prompts for user login, boot to a live cd = can't access the file system...it's all loop files and other binary, etc etc), but they are all not possible as it is an embedded linux setup the way it is. Any help/suggestions would be appreciated. Thanks

  Read the article

• Authenticating Linux users against AD without Likewise Open

  - by Graeme Donaldson

  Has anyone got their Linux systems authenticating against Active Directory without using Likewise Open? We are close to implementing Likewise Open, but first we need to rename roughly 70 of 110 Linux servers so that their hostnames are not longer than 15 characters. This is required because Likewise Open actually joins the Linux computer to the domain, and it fails to do so if the hostname is too long due to some legacy NetBIOS naming limitation. Is there a way to authenticate via AD, using only LDAP perhaps? What are the advantages/disadvantages over doing it like that vs just using Likewise?

  Read the article

• Linux and Windows Server Setup

  - by Brian

  Hello, I have an win 2008 R2 machine (a home machine of mine) that I am messing around with and learning the server technologies. I also wanted to try out oracle, and was wondering if its possible to setup a LINUX machine with Oracle, and have the two interoperate. What I mean by that is if I setup the server and my laptop on a domain, would it be possible to communicate to that LINUX machine and thus the Oracle database, and if so, are there any good resources on the setup? I was going to create a LINUX hyper v virtual... Any tips appreciated. Thanks.

  Read the article

• Linux or Windows for a server?

  - by Matt

  I'm a Linux guy when it comes to (web) servers for the following reasons Legally free Fast software updates (Unless you're running Cent OS :) Powerful CLI management of services Easy to secure (in terms of users and groups) Web server software is, well, built for Linux... Apache, PHP, Python, etc, are Linux programs that get ported to Windows - I'm 90% sure of this Unless the web server needed to run ASP, I wouldn't use Windows. My boss' IT friend is a Windows guy, though. He recently got a server setup in the office to run Microsoft Exchange and some other shit. What I'm asking is, if he wanted to start running websites on this thing, what would be good reasoning to convince him otherwise? He's not very bright in terms of IT and the IT friend is all Windows. So it's two against one here... What would you say to running a Windows web server?

  Read the article

• Linux Bridge, Samba netbios name/hostname access

  - by Christopher Wilson

  I am currently running a linux bridge in the following configuration ADSL Modem: 192.168.1.1 Linux Bridge: eth0: 192.168.1.2 eth1: no address Wireless Router: 192.168.0.1 My issue is that i cannot access the "Linux Bridge" shares using the WINS name of the server via client systems (yes i understand it is a transparent bridge but i can access it via the 192.168.1.2 address this is not on the same subnet as the client systems). This is the global section of my SMB.CONF [global] unix extensions = off os level = 20 netbios name = server guest account = nobody server string = 447 Server security = share #unix extensions = no #wins support = yes #wins server = 192.168.0.1 name resolve order = wins lmhosts hosts bcast interfaces bridge1 eth0 eth1 lo bind interfaces only = yes Can i access a bridged server using it's WINS name to access samba shares? Cheers Chris

  Read the article

< Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >