Search Results

Search found 2953 results on 119 pages for 'mikew co'.

Page 61/119 | < Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >

• Infected Win XP disk not openable on a Vista computer

  - by Retired57

  How can I read a WinXP partioned disk that is infected and shows up on a USB connection to Win Vista computer as a single partition that Vista cannot see the contents? The XP computer HDD is partioned into 4 partitions. It became infected, and all attempts to clean it have failed. Applications begin to launch, but are then shut down by the infecting agent. Using a major Anti-virus Co. boot disk (which was unable to connect to the Web, probably because the infecting agent stopped it) with virus definitions dated after the disk became infected, the resultant scan showed no infection. I bought a USB cable to connect the IDE drive to my Vista computer, but when I open Win Explorer, it sees the disk, but does not show any contents. It indicates it is a single partition that is valid. However in all the ways I have tried it does not show drive contents. Any suggestions on what to do next?

  Read the article

• Multiple Graphics Cards on Fedora 15 (Gnome 3)

  - by Michael

  I have the (delightful) misfortune of having 3 graphics cards. They are XFX Radeon 5750s. Each drives 2 monitors via dvi. I am having a really hard time getting these running on fedora 15 (gnome 3). So my setup is 3 columns of 2 monitors (the upper monitor is mounted upside down in each column to reduce the bezel between monitors). When the (graphical) login screen comes up all 6 have the blue stripey background that must be the default, but then when I login, things get interesting. In the xorg.conf below, you will see only 2 of the screens in the serverlayout while the other 4 are commented out. Logging in with only 2 of the screens active works well (and it even remembers that the top one is upside down, and should be considered above the lower, i am not sure where it stores this info, but i set it using the graphical "Displays" settings) However, as soon as I uncomment a third screen, or more, it gives me an error message when I login. It's one of those friendly, less helpful messages (Oh no! Something has gone wrong. A problem has occurred and the system can't recover. Please log out and try again). If i do not use an xorg.conf, then the "Displays" prefs pane shows only the two monitors on one of my graphics cards Thanks to anyone who can help me get going! (xorg.conf and then lspci below, and xorg log) xorg.conf Section "ServerLayout" Identifier "X.org Configured" Screen "Screen0" 0 0 Screen "Screen1" Below "Screen0" # Screen "Screen2" RightOf "Screen0" # Screen "Screen3" RightOf "Screen1" # Screen "Screen4" RightOf "Screen3" # Screen "Screen5" RightOf "Screen4" InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Files" ModulePath "/usr/lib/xorg/modules" FontPath "catalogue:/etc/X11/fontpath.d" FontPath "built-ins" EndSection Section "Module" Load "record" Load "dri" Load "dbe" Load "extmod" Load "dri2" Load "glx" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor2" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor3" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor4" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor5" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Device" Identifier "Card0" Driver "radeon" BusID "PCI:4:0:0" EndSection Section "Device" Identifier "Card1" Driver "radeon" BusID "PCI:5:0:0" EndSection Section "Device" Identifier "Card2" Driver "radeon" BusID "PCI:6:0:0" EndSection Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Card0" Monitor "Monitor1" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Card1" Monitor "Monitor2" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen3" Device "Card1" Monitor "Monitor3" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen4" Device "Card2" Monitor "Monitor4" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen5" Device "Card2" Monitor "Monitor5" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection lspci output follows [tgm@tgm ~]$ lspci 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:14.3 PIC: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers (rev 13) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.2 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 3 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller #1 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller #2 02:00.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 03:00.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 03:02.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 04:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 04:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 05:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 05:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 06:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 06:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) xorg log (posted to fpaste due to how long it is. thanks to marcusw for the request) http://www.fpaste.org/r5ww/ xorg log with all 6 monitors enabled in xorg.conf (they all turn on and have blue, but then one gets the aforementioned user-friendly error message). http://www.fpaste.org/X63H/

  Read the article

• How to fix windows new line character on sftp synchronization in eclipse (pdt)

  - by superspace

  Hello, I have a problem with windows new line characters being introduced into text files on eclipse sftp synchronization (via jcraft's sftp plugin). I've set "New text file line delimiter" to Unix and have even sanitized the file with "fromdos" but every time i upload using the sftp plugin, windows new line characters can be seen in the remote file as "^M" characters (when viewed in vi). A point to note is that if i upload using an external sftp client, it's all fine. Eclipse Version: PDT (Helios) SFTP: jcraft sftp plugin Local Environment: Ubuntu 10.04 Remote Environments: FreeBSD 6.4, Debian 4.0 What am i missing? My co-workers would thank you for the solution :) Thanks in advance.

  Read the article

• Is there any way of preventing .csv files being converted into excel format

  - by Kevin Trainer

  I'm trying to work with an automated testing tool which can use .csv files as its data sourse. After saving a notepad file containing a number of fields and data seperated by commas as .csv it appears to have been converted to an excel file. When I run the test, only the first line of values is identified and can be run within the automated test. Not sure if this is expected with the testing product (www.badboy.co.au), but just wondered if there was a way of preventing excel from taking control of the .csv file? Any helpfull feedback would be great.

  Read the article

• Big Excel File Freezing/Running Slowly

  - by ktm5124

  Hi, My co-worker has a very large Excel file (over 7 MB) that suffers from the problems of (A) running slowly (B) taking forever to open/save/close and (C) freezing the computer, requiring a restart. I set the calculations to Manual, and I repaired the file, but the file didn't change in file size and it is still having these problems. My questions are: (1) Is there any way around this problem or is Excel just bad at handling ~7MB files? (2) Would upgrading RAM make a big difference? (3) It's possible that we can't afford to spend the money on a RAM upgrade. Are there are any other ways of mitigating the problem? Thanks.

  Read the article

• Win Server 2008 R2 - Mapped shared folder hanging?

  - by M-Tech

  I have recently built a windows 2008 server R2 machine. This is purely for file server purposes and is very much a basic build. All windows updates installed and part of domain. I have setup a shared folder on the C:Drive and added permissions for domain users as co-owners. The client machines run XP SP3 and are part of the domain also. We have a few servers running the same setups on a few of our sites but this one is particular crashes users machines (explorer.exe hangs for at least a few mins) when attempting to access the shared folder. I have turned off the option on the network card for power save aswell still no change. Any help with this is very much appreciated and i look forward to hearing from you ;)

  Read the article

• Resize image on ViewSonic CD3200-EU

  - by JohnLBevan

  My ViewSonic CD3200-EU monitor doesn't seem to have an option to scale the image vertically. I've tried all the buttons which look promising and even went as far as browsing the manual (possibly my first time). http://www.viewsoniceurope.com/uk/assets/004/9269.pdf Does anyone know if this can be done? I'm connecting with an android hdmi stick (http://www.amazon.co.uk/gp/product/B008XX29WS/ref=oh_details_o00_s00_i00) so if there's any way to change screensize that way that would also be appreciated. Thanks in advance.

  Read the article

• Where to look for regular scripts?

  - by fontan

  It seems to me that our server freezes every 30 days around noon due to the huge utilization of xvda data transfer partition - writes are 50 times higher than normally (according to the health monitor in plesk). This seems to me as the reason why the apache & co becomes instable as (for example) all apache's processes are waiting to write their log (according to the service's full status). I am, however, unable to find any scheduled task that would be executed during that period. I have checked both cron and anacron setup and there is only one monthly anacron task which is not executed (according to the /var/log/cron - and there is nothing unusual) around noon. Are there any other places where to look for periodical processes? (I am just about to ask server's provider the same question about any external maintenance run around this time but I don't expect them to run anything time/resource consuming during the day.)

  Read the article

• connecting 2 ubuntu computers as a lan

  - by Brendan Cutjar

  Hi i am trying to connect 2 ubuntu computers as a LAN. In my current setup I have: One machine running ubuntu 11.10 with Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller While the other machine is running Ubuntu 12.04 with an Atheros Communications Inc AR8152 v1.1 Fast Ethernet The two machines are connected via a switch (Edimax ES-3205P). Unfortunately I still cannot connect the two machines together. Can somebody please show me what to do and how to go about solving this issue?

  Read the article

• OpenBSD: Gateway outside subnet (works in Linux)

  - by kshade

  We need to set up an OpenBSD host to use a default gateway that's outside of it's subnet. This is all I need to do on Linux (not the actual IPs) to achieve it: ifconfig eth0 33.33.33.33/31 up route add 33.33.33.254 dev eth0 route add default gw 33.33.33.254 The problem is that we don't know the proper equivalent of the middle command in OpenBSD. The man page says: If the destination is directly reachable via an interface requiring no intermediary system to act as a gateway, the -iface modifier should be specified; Sadly we can't seem to figure out how to make it work with that. This is a virtual host on an OVH server, they have documentation for many other operating systems showing how to do it here: http://help.ovh.co.uk/BridgeClient

  Read the article

• How can I get Google to re-point its search entries to new domain?

  - by poolski

  My main .com domain registration lapsed and when I went to re-register it, I found that a domain reseller service squatted it and I've lost access to it. As I wasn't terribly keen on spending money on funding scammers and the like, I registered a .co.uk domain under the same name. Is there any way of getting Google to re-point all its indexed links to the new domain? It's been indexing my blog for a couple years now and while it's not too big a deal, I'd like to not have to start all over again. Also, searching for my site results in an old entry which is currently pointing at a "Apply for a Tax Break NOW!!!" page.

  Read the article

• Redirect non-www ssl traffic to www ssl (apache)

  - by The NinjaSysadmin

  Hello, I'm attempting to get a redirect which is failing, and for some reason I can't think today. I have a vHost file within HTTPD that listens on standard port 80 and port 443. I'm attempting to redirect https://domain.com/(.*) to https://www.domain.com/$1 so that the URL remains intact. My config is as follows: ServerName www.domain.com ServerAlias tempdomain.testdomain.co.uk ServerAlias domain.com My rerwrite rule I'm using is. RewriteCond %{HTTP_HOST} ^domain.com$ RewriteRule ^(.*)$ https://www.domain.com$1 [R=301,L] I've also tried removing the . and $ but nothing.. When I visit the url https://domain.com/secure.page?action=comp it doesn't redirect to https://www.domain.com/secure.page?action=comp I do also have other SSL pages, the above was just an example.. Can anyone point out my stupidity.

  Read the article

• Would a switch be covered by a router's firewall

  - by Uh-yeah...

  So... Hopefully; this is the right place for this question. I need more Ethernet ports on my home network. Sadly, we already have an old router connected to the main router and we still need more ports. I feel dumb for asking; but, I just would like to double check. Would the devices connected to the switch be "protected" by the Main router's firewall? ? Up to this point I have assumed that was the case; but, a co-worker is convinced that is not the case [ I believe he is thinking of a situation in which the switch (un-managed) is before an access point]. [It would go modem to main router; main router then has the switch and old router connected to it.

  Read the article

• Enable (or work around) Administrative shares in Windows 8

  - by Brado

  So in using Windows 8, I've discovered that the administrative shares are disabled. There seems to be no easy way to get them re-enabled. Is anyone aware of a work around, or solution? I did not have this issue with Windows 7 After disabling UAC. However in Windows 8 this still doesn't work. This is all I could find, however I am not satisfied with the information provided. http://www.computerperformance.co.uk/win8/windows8-administrative-shares.htm http://www.tomsitpro.com/articles/windows_8-file_sharing-windows_administrative_shares,2-195.html

  Read the article

• Device that connects to a switch via RJ45, that emulates a PC

  - by Mike Christiansen

  One of my co-workers once saw a device that plugged into a RJ45 jack, that emulated a PC. It could be configured with an IP address, and respond to pings. I was wondering if anyone knew about these, or even what they are called? This will be used to simulate a PC in a classroom environment. Thanks in advance. Edit: This is a CCNA classroom, we are looking to simulate a PC connected to an ethernet port on a router. These will be on different subnets, etc. This might be doable with a VM through VLANs and virtual switches, but then we are getting away from configuring the physical ports on the router the way we want to.

  Read the article

• Windows Server 2008 - Setting Up DNS and Web Server (IIS) to host personal website?

  - by Car Trader

  Okay, I have a server, (Windows Server 2008 R2 to be more precise) and I have installed PHP, MySQL, phpMyAdmin, for web hosting purposes. I have set up a static ip address internally. I have installed the role DNS and Web Server (IIS) role. I now set up my forward looking zone as my chosen domain. I set up the nameservers as ns1.domain.co.uk with my IP address which I found from whatismyip.org. However, when I type my IP address, it times out with an error (Timeout Error). Am I doing something wrong? Am I missing something? Also I have seen that most websites have multiple nameservers, which are apparently mirror IP addresses which all redirect to one IP address. Also, I can locally connect using the IP address 192.168.0.8, however, I want to put my website online/live on the internet. Can anyone help me with this? -- Regards

  Read the article

• What TLDs should I use for my NS records for redundancy? (DNSSEC support required)

  - by makerofthings7

  Question As a general practice, is it a good idea to use multiple TLDs for the name servers? How should I choose between which TLD would be a good candidate for being the root server for my NS name? More Info I am switching over 800 DNS zones to an outsourced DNS provider. I originally planned on setting the zone names to nsX.company.com, but think it would be best to have multiple TLDs such as .net , .org and .info Since I plan on supporting DNSSec at company.com I think all the 1st tier Name servers must support it as well. Part of the inspiration for this question came from our provider UltraDNS. In their configuration screen for our domains, they actively verify and alert us if our name servers aren't exactly: pdns1.ultradns.net pdns2.ultradns.net pdns3.ultradns.org pdns4.ultradns.org pdns5.ultradna.info pdns6.ultradns.co.uk

  Read the article

• Video streaming over multi display units

  - by ramdaz

  We have to share video across around 4/8 terminals at a public facility where we need to display live video from within the facility, as well as display messages(advertisements), and also play videos(not live) which need to be controlled centrally from another location. We can do central location handling over Internet, over ssh. What we want to do is connect cameras to a computer, and use the computer to display over multiple display units. We need to do live titling if possible. Once the live local telecast which usually takes about an hour or two a day, we would like to play other videos locally off the PC server. Preferably everything should run off Linux, since budgets are very constrained.... Addendum -- Its not over WAN, it's over a local area. I prefer not using LAN, we would rather use co-axial cable if possible. The reason is if it's LAN, I need some kind of an Networking device, at least a thin client

  Read the article

• Problem with Lenovo x200s Wifi under Ubutu Karmic

  - by oneself

  Hi, I have just gotten my Lenovo X200s laptop, and I am install Ubuntu 9.10 Karmic on it. The installation went through without a hitch, but I can't get my wifi to work. lspci | grep Network Produces the following results: 00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03) 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8172 (rev 10) The weird part is that when I turn the wifi hardware stitch on and off on the side of the laptop, I get the following printed in /var/log messages: Dec 30 23:24:48 temp-laptop kernel: [ 213.432302] usb 4-2: USB disconnect, address 2 Dec 30 23:24:52 temp-laptop kernel: [ 217.276310] usb 4-2: new full speed USB device using uhci_hcd and address 3 Dec 30 23:24:52 temp-laptop kernel: [ 217.441759] usb 4-2: configuration #1 chosen from 1 choice Does Ubuntu think my wifi card is a USB device? Am I missing some driver? What can I do to fix this? Please, help!

  Read the article

• where is this SPF problem occuring

  - by Saif Khan

  Hi, Inbound mail to a specific user is been forwarded to his external mailbox at another domain. Add mails are routed correctly with the exception of one domain. When mail are sent to users of my domain, including that user, the mails are delivered to everyone except him...as the mail admin I am getting the message The following recipient(s) cannot be reached: usermailbox on 1/10/2011 1:27 PM There was a SMTP communication problem with the recipient's email server. Please contact your system administrator. email.speedimpex.com #5.5.0 smtp;587 someone@somedomain.co.uk sender domain does not match SPF records I am sure this has nothing to do with my mail server, however, can someone confirm?

  Read the article

• Enterprise Data Center System Admin/Engineer to Server Ratio

  - by Bob

  I know there have been similar questions asked over the last few months however looking at a Data Center Operations and know there are some really smart people out there that might be able to help. Looking for some staffing best practices based on first hand experience and was hoping that there is some experience in this area that can provide "best practice" application: Three High Availability (99.99% plus) Enterprise Level Data Centers geographically dislocated, one manned 24x7x365, one lights out, one co-location running HOT-HOT-HOT supporting a global community. More than 2,000 operating systems consisting of 95% Windows, 5% Linux and Solaris, 45% virtualized, more than 100TB storage. No desktop support, no Network Administration (administrated separately), running N+1 and serving more than 250 Billion page views annually. Based on experience what has been your experience with Server to "Data Center System Administrator/Engineer" ratio? Thanks in advance for your responses.

  Read the article

• What is the procedure to replace a failing hard drive in a RAID array?

  - by slayton

  3 years ago a co-worker setup a software RAID-6 array on Ubuntu 9.04 and I'm getting messages from the OS that the drive has bad sectors and should be replaced. I'd like to remove this drive and replace it with a new drive, however, I have never done this before and I'm terrified that in the process of fixing the array I'm going to end up ruining it. I know the device ID of the array and I know the device IDs of the individual drives in the array. Additionally I physically have the bad drive. What are the steps to replace the bad drive with a new drive and get the array running again?

  Read the article

• Can I add right-click options in Google Chrome?

  - by andygrunt

  In Google Chrome, if I select a piece of text and right click on it, I get the option to: 'Search Google for [text]' I find this extremely useful but I'd also like to be able to add my own options. For example, I'd like to add the ability to search amazon.co.uk using the selected text or go straight to Google maps using the selected text (i.e. an address or postcode) and so on. I can sort of add this functionality using PhraseExpress but would rather be able to do it straight from Chrome - is it possible?

  Read the article

• Load balanced proxies to avoid an API request limit

  - by ClickClickClick

  There is a certain API out there which limits the number of requests per day per IP. My plan is to create a bunch of EC2 instances with elastic IPs to sidestep the limitation. I'm familiar with EC2 and am just interested in the configuration of the proxies and a software load balancer. I think I want to run a simple TCP Proxy on each instance and a software load balancer on the machine I will be requesting from. Something that allows the following to return a response from a different IP (round robin, availability, doesn't really matter..) eg. curl http://www.bbc.co.uk -x http://myproxyloadbalancer:port Could anyone recommend a combination of software or even a link to an article that details a pleasing way to pull it off? (My client won't be curl but is proxy aware.. I'll be making the requests from a Ruby script..)

  Read the article

• Run a specific command from a directory

  - by Cameron Kilgore

  I have a bash script where I need to run an init utility within a directory with a configuration file defined. I don't think it's possible to explicitly tell the utility to run the file as an argument, so what I need to do is go to the directory with the config file, and then run the command. I have some logic in place, but its not working -- the utility never runs. Is there any way I can tell the script to go to this directory, and then run the script? cd /var/www/testing-dev.example.co eval "standardprofile"

  Read the article

< Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >