Search Results

Search found 17567 results on 703 pages for 'muon package manager'.

Page 61/703 | < Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >

• Package upgrade on Ubuntu raid server and grub setup issue

  - by RecNes

  I have remote Ubuntu 10.10 server running on raid system. I did package upgrade yesterday night for security reasons. During the upgrade, grub installation screen appeared and asked me which partition I wanted to install grub. Options are sda,sdb,md1 and md2. I decide to install them on both sda and sdb partitions. I wondering, was I make true decision? If machine get reboot is it can be boot up safely? You can find fdisk output and fstab mount points below: Fstab: proc /proc proc defaults 0 0 none /dev/pts devpts gid=5,mode=620 0 0 /dev/md0 none swap sw 0 0 /dev/md1 /boot ext3 defaults 0 0 /dev/md2 / ext3 defaults 0 0 Fdisk: Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00029bb5 Device Boot Start End Blocks Id System /dev/sda1 1 262 2102562 fd Linux raid autodetect /dev/sda2 263 295 265072+ fd Linux raid autodetect /dev/sda3 296 91201 730202445 fd Linux raid autodetect Disk /dev/md0: 2152 MB, 2152923136 bytes 2 heads, 4 sectors/track, 525616 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Disk /dev/md1: 271 MB, 271319040 bytes 2 heads, 4 sectors/track, 66240 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md1 doesn't contain a valid partition table Disk /dev/md2: 747.7 GB, 747727224832 bytes 2 heads, 4 sectors/track, 182550592 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md2 doesn't contain a valid partition table Disk /dev/sdb: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00088969 Device Boot Start End Blocks Id System /dev/sdb1 1 262 2102562 fd Linux raid autodetect /dev/sdb2 263 295 265072+ fd Linux raid autodetect /dev/sdb3 296 91201 730202445 fd Linux raid autodetect

  Read the article

• MSDTC - Communication with the underlying transaction manager has failed (Firewall open, MSDTC network access on)

  - by SocialAddict

  I'm having problems with my ASP.NET web forms system. It worked on our test server but now we are putting it live one of the servers is within a DMZ and the SQL server is outside of that (on our network still though - although a different subnet) I have open up the firewall completely between these two boxes to see if that was the issue and it still gives the error message "Communication with the underlying transaction manager has failed" whenever we try and use the "TransactionScope". We can access the data for retrieval it's just transactions that break it. We have also used msdtc ping to test the connection and with the amendments on the firewall that pings successfully, but the same error occurs! How do i resolve this error? Any help would be great as we have a system to go live today. Panic :) Edit: I have created a more straightforward test page with a transaction as below and this works fine. Could a nested transaction cause this kind of error and if so why would this only cause an issue when using a live box in a dmz with a firewall? AuditRepository auditRepository = new AuditRepository(); try { using (TransactionScope scope = new TransactionScope()) { auditRepository.Add(DateTime.Now, 1, "TEST-TRANSACTIONS#1", 1); auditRepository.Save(); auditRepository.Add(DateTime.Now, 1, "TEST-TRANSACTIONS#2", 1); auditRepository.Save(); scope.Complete(); } } catch (Exception ex) { Response.Write("Test Error For Transaction: " + ex.Message + "<br />" + ex.StackTrace); }

  Read the article

• Mac: window manager frozen, have ssh access

  - by Bernd

  I have a Mac which regularly runs into a problem. The user interface stops reponding, showing a "frozen" user interface. The mouse is still moving but clicking does not trigger anything. This happens about once a week. Solution so far is to force switch-off the Mac and reboot it. I have ssh root access to the Mac. Killing (kill -9) the active application has no visible impact on what is shown on the screen. Any ideas on how to diagnose this? Is there a way to restart the window manager from the ssh shell? Killing /System/Library/Frameworks/ApplicationServices.framework/Frameworks/CoreGraphics.framework/Resources/WindowServer seems not to be possible. The Mac is an early 2008 iMac and runs Lion with latest updates. /Library/Logs/DiagnosticReports is empty. Update: Problem stays after update to Mountain Lion. The WindowServer process is in "uninterruptible wait" state ("U" flag in ps output set): imac:~ root# ps ax|awk "NR==1|| /WindowServer/"|grep -v awk PID TT STAT TIME COMMAND 86 ?? Us 50:51.69 /System/Library/Frameworks/ApplicationServices.framework/Frameworks/CoreGraphics.framework/Resources/WindowServer -daemon Any idea for diagnosing what blocks the process? Any idea for "waking up" the process?

  Read the article

• Win7 Credential manager and accessing SQL Server from outside of the domain

  - by David Lively

  My SQL Server is set to use windows authentication. If I am connected to the domain directly from my Win7 Ultimate x64 machine, SQL Management Studio (SSMS) will let me authenticate with Windows authentication. However, if I am connected via the VPN (from a different machine that is not joined to the domain), it won't. If I start SSMS with the following command line: C:\Windows\system32>runas /netonly /user:domainname\username "C:\Program Files (x86)\Microsoft SQL...\ssms.exe" then connecting to the SQL Server (which is in the domain) with Windows Authentication works fine. I'd like to save these credentials so that I don't have to launch SSMS from the command line, or modify the shortcut. I know I can use the SysInternals ShellRunAs extension to do this, but I again have to enter my domain username and password each time, and shift+right-click to see that menu option. The Windows Credential Manager seems designed to solve this problem, and works for network shares. However, it doesn't seem to work for SSMS. Any suggestions? I've tried using the /savecred option with runas to create the necessary credentials, but that appears to be incompatible with the /netonly option. Running the above command line with the addition of /savecred just displays the runas help screen. Grrr. Argh.

  Read the article

• Error setting up Data Protection Manager 2010 Agents / Network "Unauthenticated" in network settings

  - by Bowsa

  I'm not sure if the two are connected but i suspect they are. Basically I'm tring to setup Data Protection Manager 2010 on a fresh install of Server 2008 R2 in a SBS 2003 domain. Everything went fine until trying to install agents across the network. Upon clicking add, i get the following error message: Unable to connect to the Active Directory Domain Services Database. Make sure that the DPM server is a member of a domain and that the controller is running. Also verify that there is network connectivity between the DPM server and the domain controller. ID: 7 As usual (worryingly) the MSDN support for 2010 products is nearly non existant, clicking the error ID simply gives a page not found error. So after 2 days of Googling and trying various fixes (DNS settings, adding permissions to AD objects, rejoining the domain and many more) I thought I'd ask here in the hope that someone out there may have had this issue before. Any help greatly appreciated! Some further info: Firewalls are disabled on the Server 2008, SBS, and client machines. Manually installing and adding the client in also fails, as the DPM server tries to contact the DC first. Edit: I tried creating a new protection group instead, and it gives a different error upon adding the machines: Following machines are not found in AD: COMPUTERNAME.COMPANYNAME.LOCAL Is there a certain directory structure it follows in AD?

  Read the article

• WebHost Manager - Apache's VHost isn't matching the DNS entry

  - by Trans

  I've used CPanel's WebHost Manager to create a new host on my VPS. I then used my HOSTS file to point fake.com to the relevant IP address. The problem I'm having now is, Apache isn't recognizing the VHost,or something, as it's just loading the default entry and 404'ing every document I try to GET. Here's the VHost entry NameVirtualHost 0.0.0.209:80 NameVirtualHost 0.0.0.211:80 <VirtualHost 0.0.0.209:80> ServerName fake.com ServerAlias www.fake.com DocumentRoot /home/fakecom/public_html ServerAdmin [email protected] ## User fakecom # Needed for Cpanel::ApacheConf <IfModule mod_suphp.c> suPHP_UserGroup fakecom fakecom </IfModule> <IfModule !mod_disable_suexec.c> SuexecUserGroup fakecom fakecom </IfModule> CustomLog /usr/local/apache/domlogs/fake.com-bytes_log "%{%s}t %I .\n%{%s}t %O ." CustomLog /usr/local/apache/domlogs/fake.com combined Options -ExecCGI -Includes RemoveHandler cgi-script .cgi .pl .plx .ppl .perl ScriptAlias /cgi-bin/ /home/fakecom/public_html/cgi-bin/ </VirtualHost> I've Google'd this profusely and all that's being returned is 'DNS errors. Wait for it to propagate'. That's obviously not my problem, since I'm using HOSTS. What else could be causing this? :/ EDIT: Forgot to mention. http://fake.com/~fakecom/test.html loads just fine. So the fake.com is pointing to the right IP.

  Read the article

• Archive Manager, SQL 2005 and MaxTokenSize high CPU

  - by Tim Alexander

  So, I posted this question a few days ago: Impact of increasing the MaxTokenSize for Kerberos Tickets Since then the thought was to test our settings on two member servers, one with IIS and one without. I setup two GPOs to configure the MaxTokenSize reg setting to 48000 and MaxFieldLength/MaxRequestBytes to 64200 (based on MS KB2020943, these are set at 4/3 * T + 200). The member server seemed to work ok (a devalued tape backup server). The IIS server however has had some strange repercussions. The IIS Sserver host Quest Software Archive Manager (AM) 4.5 that communicates with SQL Server 2005 Enterprise on Server 2003 R2. After the changes all looked good until the SQL Server hit 100% CPU. I have removed the GPOS, removed the reg values and even replaced them with defaults (12000 for token size and can't remember the other one but was in a blog post about the issue in my other post). No change. Bouncing the IIS Server stops the high CPU and a colleague has looked at the SQL server and it is definitely the AM connection taking up the time/work on the SQL server. I haven't changed the reg values on the SQL server or the DCs but am reluctant to do so without understanding why this has happened. I am guessing its to do with the overriding auth and group issue we have but I am not seeing Kerberos errors in either event log. Has anyone seen something similar or does anyone have some tips? Was definitely blindsided by the Kerberos issue and am swimming against the tide to keep things functioning.

  Read the article

• Windows 7 won't boot from any bootloader except for Windows Boot Manager after partition resize

  - by user2468327

  I have a triple boot system on a single SSD: OSX, Windows 7, and Ubuntu. I use Chimera (basically another version of Chameleon) as my bootloader. Usually I can boot all 3 OSs without any issue, but after using GParted to make my Ubuntu partition 2 Gigs larger, Windows 7 throws me an error when trying to boot to it from either Chimera or Grub. The error is consistently: `0xc000000e can't find \Boot\BCD" (slightly paraphrased). However, I can still get into Windows by selecting Windows Boot Manager from the boot options in my BIOS. I've already tried several known fixes for similar issues, including bootrec /rebuildbcd (and variations), and BootRec.exe/fixMBR + BootRec.exe/fixBoot. I've also tried Chkdsk. At best this has made it so Windows 7 boots on its own by default (making me have to reinstall Chimera and change back my boot settings in the BIOS). At worst this made it so Windows won't boot period. Now I'm back full circle where I started. A detail that might be useful is that bootrec /rebuildbcd says that the number of found Windows installations is 0. I'm fairly certain that I don't have a hybrid MBR. Mainly because I have a UEFI BIOS, and with that, it appears each OS can support a GPT. So it would kind of pointless to have and deal with. I may be wrong though, I couldn't find any way of finding out for sure online. However, I know for sure that the version of Windows I have installed is the UEFI version, as well as every partition tool I've used to look at my boot drive tells me it's GPT. How do I get it back so I can boot Windows 7 through another bootloader so I don't have to manually select it in the BIOS? Preferably without a reinstall.

  Read the article

• In a Shell scripts, check version of installed package, make a decision based on output

  - by DJDarkViper

  Looking to write a cross distro / cross version shell script that makes sure a forced version of PHP is installed Example: Ubuntu 12.04 has 5.3, Ubuntu 13.10 has 5.5, Debian 7 has 5.4 I need this script, when run on a distro that has an old version of PHP, to update the repo to point to a package for 5.4, and if the distro has too new of a version, can downgrade to 5.4 appropriately. Im still not entirely comprehensive of Shell/Terminals technical limit of what you can do with it, but ill be perfectly frank that im still not totally used to existing tools The best I can think at the moment is: php -v | grep "PHP 5" but that returns a bunch of potentially changeable granular characters (PHP 5.4.4-14+deb7u5 (cli) (built: Oct 3 2013 09:24:58) ). Im not sure what to pipe to after this to extract out the characters im interested in Im not sure if im being totally clear, im not sure how to ask this.. Basically, in an automated shell script for Linux distros, how do I extract the PHP version (and just the PHP version number preferably) and make a decision based on that output EDIT This line ended up doing pretty dang good php -v | grep "PHP 5" | sed 's/.*PHP \([^-]*\).*/\1/' | cut -c 1-3 Bit long in the tooth, but gives me "5.3", "5.4", and "5.5" which is exactly what I need to work with

  Read the article

• Trouble getting started with the STEALTH monitoring package

  - by dlanced

  Is anyone here familiar with the Linux-based STEALTH package (for monitoring FS integrity of client systems)? I'm trying to get started with a very simple configuration, but I'm running into trouble (this is running under Ubuntu 14.04): Config line `USE BASE/root/stealth/10.0.0.79' invalid STEALTH (2.11.02) started at Fri, 30 May 2014 15:25:00 +0000 Program terminated due to non-zero exit value for -type f -exec /usr/bin/sha1sum {} \; (EOC Fri May 30 15:25:00 2014 127) Stealth is creating a binary tmp file in the Stealth server root and generating a "report" file in the start directory, but not much else. Regarding the "USE BASE...invalid" error, and just to be sure, I manually created the directories in /root, but it didn't help. And, by the way, I am running stealth with sudo. Everything seems to be configured correctly: I'm able to ssh into root@client from the stealth machine without a password Here's my "policy" file (I've removed the email directives just for simplicity): DEFINE SSHCMD /usr/bin/ssh [email protected] -T -q exec /bin/bash --noprofile DEFINE EXECSHA1 -xdev -perm +u+s,g+s ( -user root -or -group root ) \ -type f -exec /usr/bin/sha1sum {} \; USE BASE/root/stealth/10.0.0.79 USE SSH ${SSHCMD} USE DD /bin/dd USE DIFF /usr/bin/diff USE PIDFILE /var/run/stealth- USE REPORT report USE SH /bin/sh GET /usr/bin/sha1sum /root/tmp LABEL \nchecking the client's /usr/bin/find program CHECK LOG = remote/binfind /usr/bin/sha1sum /usr/bin/find LABEL \nsuid/sgid/executable files uid or gid root on the / partition CHECK LOG = remote/setuidgid /usr/bin/find / ${EXECSHA1} LABEL \nconfiguration files under /etc CHECK LOG = remote/etcfiles \ /usr/bin/find /etc -type f -not -perm /6111 \ -not -regex "/etc/(adjtime\|mtab)"\ -exec /usr/bin/sha1sum {} \; Any ideas? Thanks,

  Read the article

• DNS manager in Windows Server 2012 Essentials - My one server appears twice

  - by tetranz

  I have a newly installed Windows Server 2012 Essentials. It works pretty good although I'm working on some DNS improvements. Something that seems a little weird is in DNS Manager, my server appears twice. Once as hostname and once as hostname.mydomain.local. They seem to be identical and locked in sync. If I change one, the other follows. Is this normal? Does anyone know why I have this? I'm talking about the top level on the navigation. The very top is DNS and then these two below. Zones, forwarders etc are below them. I've found a couple of forum posts of people asking the same thing but no useful answer. All tutorials etc I can find with screenshots show only one which makes me uncomfortable. The server was installed out of the box as standard with the wizards. I know about the recommendation not to use .local but the wizards didn't give me any other option.

  Read the article

• Todo/task manager for android and desktop linux

  - by RiaD

  I'm looking forward to Task/ToDo Manager. It should work under Android, Linux(or Web). If it's very cool, one of them is OK too, Android is preferable in this situation. Necessary features: Russian or English language Possibility to mark task as finished Interesting features: (I want as more, as possible, while it's OK, if some of them isn't avaliable) Nice and easy-to-use interface Possibility to choose finish time for task. After that it's showed as overdue. Possibility to choose start time for task. Before it task is inactive and maybe shown or hide Possibility to add nested tasks. Task marks completed when all sub-tasks are completed. Possibility to make dependencies. If A depends on B, and B isn't finished yet, A is inactive as in third feature. Possibility to create task in a moment without fill-all-this-forms Syncronization between version(Android to linux or Android to web) Notification (on Android only) Features, that I'm not interested in: Creating more than one todo list sharing ToDo's I've seen couple of managers. Best I've seen now is Task Coach for Linux, but I don't very like its interface, and there is no version for Android.

  Read the article

• Conflicts with file from package mysql-5.0.77

  - by Whiteyq

  I'm trying to install APC (Alternative PHP Cache) on a CentOs dedicated server. I've everything done apart from configuring phpize. Running :yum -y install php-devel gives me the following error file /usr/share/mysql/charsets/Index.xml from install of mysql-libs-5.1.57-1.el5.art.x86_64 conflicts with file from package mysql-5.0.77-4.el5_5.3.i386 etc etc for other languages So, i think the mysql version i have is too old & i more than likely need to upgrade mysql to version 5.1. Im reluctant to do this as a) its a live server (although only 3/4 domains) b) ive read ill read to recompile php if i upgrade To add to this i have plesk installed for managing domains & might need reinstalling/reconfiguring also. sorry for the long intro but its my first post & best to give as much info as possible, so my question is basically Is there any way i can run :yum -y install php-devel to get phpize working to complete installation of APC for the version of mysql i currently have installed? ie 5.0.77

  Read the article

• VzAccess Manager.

  - by bek

  I have verizon air card for my internet. Which is called vz manager. I have had it for about a year. Keeping within my usage allowance the whole time until 3 months ago, when my bill came in my 5,000 g allowance was ran to 18,000. It has continued to do so through the last 3 months. My usage reset itself yesterday for the new month. I got on google for about 5 minutes and chatted for about an hour yesterday online. Mind you that I have never done anything any different then i do everyday. I do not download music or watch videos on my computer, nothing like that. Well since last night a 8 pm my usage sayd 1109.525 gb. ALREADY! For being on the internet for an hour with no downloads. What could be causing this, please thrown me some ideas. Verizon is checking on the problem, but that usually doesnt get me the answer i want. Can someone be hacking my card and using internet through it, has told me that that is not possible, however I think with the internet anytihng is possible.

  Read the article

• How do I get a rt2800usb wireless device working?

  - by Jii

  My brand new desktop running 13.04 has endless problems with wireless. Dozens of others are flooding forums with reports of the same problems. It worked fine for a few days, then there were a few days where it started having problems sometimes and working sometimes. Now it never works at all. I have 5+ devices all able to connect without any trouble at all, including iPhone, Android phone, 3DS, multiple game consoles, a laptop running windows 7, and even a second desktop machine running Ubuntu 12.04 sitting right behind the 13.04 machine. All other devices have full wireless bars displayed (strong signals). At any moment, one of the following is happening, and it changes randomly: Trying to connect forever, but never establishing a connection. Wireless icon constantly animating. Finds no wireless networks at all. (There are 12+ in range according to other devices.) Will not try to connect to the network. If I use the icon to connect, it will display "Disconnected" within a few seconds. Will continuously ask for the network password. Typing it in correctly does not help. Wireless is working fine. This happens sometimes. It can work for days at a time, or only 10 mins at a time. Various things that usually do nothing but sometimes fix the problem: Reboot. This has the best chance of helping, but it usually takes 5+ times. Disable/re-enable Wi-Fi using the wireless icon. Disable/re-enable Networking using the wireless icon. Use the icon to try and connect to a network (if found). Use the icon to open Edit Connections and delete my connection info, causing it to be recreated (once it's actually found again). Various things that seem to make no difference: Changing between using Linux headers in grub at bootup, between 3.10.0, 3.9.0, or 3.8.0. Move the wireless router very close to the desktop. Running sudo rfkill unblock all (I dunno what this is supposed to do.) I've used Ubuntu for 6 years and I've never had a problem with networking. Now I'm spending all my time reading through endless problem reports and trying all the answers. None of them have helped. I am doing this instead of getting work done, which is defeating the whole purpose of using Ubuntu. It's heartbreaking to be honest. In the current state of "no networks are showing up", here are outputs from the random things that other people are usually asked to run: lspic 00:00.0 Host bridge: Intel Corporation Haswell DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Haswell PCI Express x16 Controller (rev 06) 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Lynx Point MEI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 04) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Lynx Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Lynx Point PCI Express Root Port #1 (rev d4) 00:1c.2 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d4) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Lynx Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-port SATA Controller 1 [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Lynx Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 610] (rev a1) 01:00.1 Audio device: NVIDIA Corporation GF119 HDMI Audio Controller (rev a1) 03:00.0 PCI bridge: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge (rev 03) lsmod Module Size Used by e100 41119 0 nls_iso8859_1 12713 1 parport_pc 28284 0 ppdev 17106 0 bnep 18258 2 rfcomm 47863 12 binfmt_misc 17540 1 arc4 12573 2 rt2800usb 27201 0 rt2x00usb 20857 1 rt2800usb rt2800lib 68029 1 rt2800usb rt2x00lib 55764 3 rt2x00usb,rt2800lib,rt2800usb coretemp 13596 0 mac80211 656164 3 rt2x00lib,rt2x00usb,rt2800lib kvm_intel 138733 0 kvm 452835 1 kvm_intel cfg80211 547224 2 mac80211,rt2x00lib crc_ccitt 12707 1 rt2800lib ghash_clmulni_intel 13259 0 aesni_intel 55449 0 usb_storage 61749 1 aes_x86_64 17131 1 aesni_intel joydev 17613 0 xts 12922 1 aesni_intel nouveau 1001310 3 snd_hda_codec_hdmi 37407 1 lrw 13294 1 aesni_intel gf128mul 14951 2 lrw,xts mxm_wmi 13021 1 nouveau snd_hda_codec_realtek 46511 1 ablk_helper 13597 1 aesni_intel wmi 19256 2 mxm_wmi,nouveau snd_hda_intel 44397 5 ttm 88251 1 nouveau drm_kms_helper 49082 1 nouveau drm 295908 5 ttm,drm_kms_helper,nouveau snd_hda_codec 190010 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel cryptd 20501 3 ghash_clmulni_intel,aesni_intel,ablk_helper snd_hwdep 13613 1 snd_hda_codec snd_pcm 102477 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel btusb 18291 0 snd_page_alloc 18798 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 i2c_algo_bit 13564 1 nouveau snd_seq_midi_event 14899 1 snd_seq_midi snd_rawmidi 30417 1 snd_seq_midi snd_seq 61930 2 snd_seq_midi_event,snd_seq_midi bluetooth 251354 22 bnep,btusb,rfcomm snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi lpc_ich 17060 0 snd_timer 29989 2 snd_pcm,snd_seq mei 46588 0 snd 69533 20 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device psmouse 97838 0 microcode 22923 0 soundcore 12680 1 snd video 19467 1 nouveau mac_hid 13253 0 serio_raw 13215 0 lp 17799 0 parport 46562 3 lp,ppdev,parport_pc hid_generic 12548 0 usbhid 47346 0 hid 101248 2 hid_generic,usbhid ahci 30063 3 libahci 32088 1 ahci e1000e 207005 0 ptp 18668 1 e1000e pps_core 14080 1 ptp sudo lshw -c network 00:00.0 Host bridge: Intel Corporation Haswell DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Haswell PCI Express x16 Controller (rev 06) 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Lynx Point MEI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 04) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Lynx Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Lynx Point PCI Express Root Port #1 (rev d4) 00:1c.2 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d4) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Lynx Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-port SATA Controller 1 [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Lynx Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 610] (rev a1) 01:00.1 Audio device: NVIDIA Corporation GF119 HDMI Audio Controller (rev a1) 03:00.0 PCI bridge: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge (rev 03) sudo iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on sudo iwlist scan eth0 Interface doesn't support scanning. lo Interface doesn't support scanning. wlan0 No scan results NOTE: This dmesg was done after a reboot where the network manager was continuously displaying the "disconnected" message over and over. So it must have been trying to connect at this time. My network was displayed in the list of options, as the only option despite other devices picking up 12+ access points. The router channel is set to auto. dmesg | tail -30 [ 187.418446] wlan0: associated [ 190.405601] wlan0: disassociated from 00:14:d1:a8:c3:44 (Reason: 15) [ 190.443312] cfg80211: Calling CRDA to update world regulatory domain [ 190.443431] wlan0: deauthenticating from 00:14:d1:a8:c3:44 by local choice (reason=3) [ 190.451635] cfg80211: World regulatory domain updated: [ 190.451643] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 190.451648] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 190.451652] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 190.451656] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 190.451659] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 190.451662] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 191.824451] wlan0: authenticate with 00:14:d1:a8:c3:44 [ 191.850608] wlan0: send auth to 00:14:d1:a8:c3:44 (try 1/3) [ 191.884604] wlan0: send auth to 00:14:d1:a8:c3:44 (try 2/3) [ 191.886309] wlan0: authenticated [ 191.886579] rt2800usb 3-5.3:1.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 191.886588] rt2800usb 3-5.3:1.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 191.889556] wlan0: associate with 00:14:d1:a8:c3:44 (try 1/3) [ 192.001493] wlan0: associate with 00:14:d1:a8:c3:44 (try 2/3) [ 192.040274] wlan0: RX AssocResp from 00:14:d1:a8:c3:44 (capab=0x431 status=0 aid=3) [ 192.044235] wlan0: associated [ 193.948188] wlan0: deauthenticating from 00:14:d1:a8:c3:44 by local choice (reason=3) [ 193.981501] cfg80211: Calling CRDA to update world regulatory domain [ 193.984080] cfg80211: World regulatory domain updated: [ 193.984082] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 193.984084] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 193.984085] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 193.984085] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 193.984086] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 193.984087] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) The router uses MAC filtering, and security is WPA PSK with cipher as auto. So, any ideas? Or is the solution just to not use 13.04 unless you have a wired connection? (I don't have this option.) If so, please just tell me straight. I survived 9.04 Jaunty, and I can survive 13.04 Raring. Update #1 Results from trying Wild Man's first answer: jii@conan:~$ echo "options rt2800usb nohwcrypt=y" | sudo tee /etc/modprobe.d/rt2800usb.conf options rt2800usb nohwcrypt=y jii@conan:~$ sudo modprobe -rfv rt2800usb rmmod rt2800usb rmmod rt2800lib rmmod crc_ccitt rmmod rt2x00usb rmmod rt2x00lib rmmod mac80211 rmmod cfg80211 jii@conan:~$ sudo modprobe -v rt2800usb insmod /lib/modules/3.10.0-031000-generic/kernel/lib/crc-ccitt.ko insmod /lib/modules/3.10.0-031000-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.10.0-031000-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2x00lib.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2800lib.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2x00usb.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2800usb.ko nohwcrypt=y I tried: gksudo gedit /etc/pm/power.d/wireless but I didn't have the package. It said to install gksu. I tried that, but of course, not having Internet, I didn't get the package. So instead I did: sudo gedit /etc/pm/power.d/wireless Which created the file. Here is the body: #!/bin/sh /sbin/iwconfig wlan0 power off I then rebooted. No change. I tried adding exit 0 to the bottom of the wireless file, and rebooted. No change. Please note that this is a desktop machine. I'm assuming power management is primarily for laptops, but the iwconfig does state that power management is on, so who knows. The recommended router changes I did not do, since the current router settings are (I think) required for some of the older devices I have, and because the current settings work on all my modern devices including Ubuntu 12.04 and Windows 7. I do appreciate the advice though, and I'll look into it when I have time. Anything else to try? Update #2 I booted into Ubuntu 12.04.3 from a dvd, and the same problems exist. I have a separate old desktop machine with 12.04 installed that has no wireless problems at all. So obviously the problem is wireless hardware compatibility in both 12.04.03 LTS and 13.04. Update #3 The same problems exist even when using a wired connection. I plugged an ethernet cable directly to the router and the network manager added an "Auto Ethernet" entry, but it cannot establish a connection to it. So the problem is not specific to wireless. Meanwhile, I purchased a Trendnet N300 wireless USB adapter, TEW-664UB. I plugged it in, but I have no idea how to get Ubuntu to try and use it. Can anyone tell me how? Can I download a package on another computer and copy the .deb over to do an install, etc? I'm installing windows 7 to double check that the internet connection works there and it's not just some magically faulty hardware. Thanks for your help.

  Read the article

• XRDP: window manager not starting

  - by niboshi

  I have setup my Ubuntu server so that I can connect and login to XRDP from Windows remote desktop. My problem is that after logging in, no window-manager is started. It only displays a single gnome-terminal with no border and gray meshed background. It seems that /usr/sbin/xrdp-sesman itself is running (from observation of ps and /var/run/xrdp/xrdp-sesman.pid). I put debugging line like touch /home/myname/aaaaa into ~/startwm.sh or /etc/xrdp/startwm.sh, but the file aaaaa did not generated after logging in, so these scripts have not been executed. (Both of them have chmod +x permission.) Am I missing some configuration file, or is there any way of further inspection? Any help is appreciated. Thanks. Contents of /etc/xrdp/sesman.ini [Globals] ListenAddress=127.0.0.1 ListenPort=3350 EnableUserWindowManager=0 # or 1 UserWindowManager=startwm.sh DefaultWindowManager=startwm.sh # or commented-out [Security] AllowRootLogin=1 MaxLoginRetry=4 TerminalServerUsers=tsusers TerminalServerAdmins=tsadmins [Sessions] MaxSessions=10 KillDisconnected=0 IdleTimeLimit=0 DisconnectedTimeLimit=0 [Logging] LogFile=/var/log/xrdp-sesman.log LogLevel=DEBUG EnableSyslog=0 SyslogLevel=DEBUG [X11rdp] param1=-bs param2=-ac param3=-nolisten param4=tcp [Xvnc] param1=-bs param2=-ac param3=-nolisten param4=tcp Contents of /var/log/xrdp-sesman.log after logging in: [20120402-21:29:34] [CORE ] starting sesman with pid 11064 [20120402-21:29:34] [INFO ] listening... [20120402-21:29:39] [INFO ] scp thread on sck 7 started successfully [20120402-21:29:39] [INFO ] granted TS access to user myname [20120402-21:29:39] [INFO ] starting Xvnc session... [20120402-21:29:40] [INFO ] starting xrdp-sessvc - xpid=11074 - wmpid=11073 [20120402-21:29:49] [INFO ] session 11072 - user myname- terminated Process tree Below is a part of ps aufx output during xrdp session: xrdp 12344 0.0 0.4 22856 8732 ? Sl Apr02 0:01 /usr/sbin/xrdp root 12346 0.0 0.0 15672 2000 ? S Apr02 0:00 /usr/sbin/xrdp-sesman root 24346 0.0 0.0 3780 872 ? S 00:00 0:00 \_ /usr/sbin/xrdp-sessvc 24348 24347 myname 24347 0.4 0.6 76468 13700 ? Sl 00:00 0:14 \_ gnome-terminal myname 24362 0.0 0.0 2220 716 ? S 00:00 0:00 | \_ gnome-pty-helper myname 24363 0.0 0.2 6912 5268 pts/13 Ss 00:00 0:00 | \_ bash myname 27902 0.0 0.0 2824 1096 pts/13 R+ 00:53 0:00 | \_ ps aufx myname 24348 0.0 0.9 24984 19216 ? S 00:00 0:01 \_ Xvnc :18 -geometry 1920x1080 -depth 24 -rfbauth /home/myname/.vnc/sesman_myname_passwd -bs -ac -nolisten tcp root 24349 0.0 0.0 16596 1304 ? Sl 00:00 0:00 \_ xrdp-chansrv Environment Ubuntu 11.10 Oneiric xrdp version: 0.5.0~20100303cvs-6ubuntu2

  Read the article

• fink hangs while compiling Octave on OS X

  - by Mark Bennett

  Disclaimer: I'm totally new to Fink. I'm trying to install Octave (Matlab open source clone) on Mountain Lion using Fink, following instructions at http://wiki.octave.org/Octave_for_MacOS_X It's a new installation of Fink, and I've also installed X11 per instructions. I'm using this command (which I believe is correct since everything's 64 bit now): sudo fink install octave-atlas It's hanging after a while, showing this as it's last output: ... Setting up xft2-dev (2.2.0-2) ... Clearing dependency_libs of .la files being installed Reading buildlock packages... All buildlocks accounted for. /sw/bin/dpkg-lockwait -i /sw/fink/dists/stable/main/binary-darwin-x86_64/x11/xinitrc_1.5-1_darwin-x86_64.deb (Reading database ... 14871 files and directories currently installed.) Preparing to replace xinitrc 1.5-1 (using .../xinitrc_1.5-1_darwin-x86_64.deb) ... Unpacking replacement xinitrc ... Setting up xinitrc (1.5-1) ... I did notice the process name on the terminal's tab was "sort", so the second time I hit this I tried Control-D (End-of-File), and this did seem to unstick it. I'm wondering if there's some misformed command and sort was trying to read from stdin? Questions: 1: Has anybody else seen this? Google wasn't helpful 2: Fink outputs a LOT of warnings and errors.... is that normal? 3: wondering if anybody's got Fink to compile Octave on Mountain Lion specifically? And whether they used just "octave" or "octave-atlas". Or if you got it working with MacPorts or Homebrew? 4: later Fink failed with "Failed: phase compiling: gnuplot-minimal-4.6.1-1 failed". I haven't started googling that yet... but wondering if anybody's see that? Also tried MacPorts but got other errors with Octave. And reading online it looks like HomeBrew also has issues with Octave on Mountain Lion. 5: Generally looking for anybody who's got Octave running on Mountain Lion with any of the package managers. I've been at this for a couple days ;-)

  Read the article

• getUserPrincipal() in JCIFS / Lan-Manager authentitation level setting in Windows 2k8

  - by Chris

  I have to find out in which exact format JCIFS stores the user principal in the "getUserPrincipal()" property. Therefor i created a test Environment like this: Windows Server 2008 Domain Controller Domain named "MYDOMAIN" Many Testusers in Active Directory Tomcat Application Server with my Web Application (which simply reads the user Principal and displays its values). The user should be logged in to the web-application with SSO therefor i need the format that jcifs is using to store the user. (For example user@MYDOMAIN or MYDOMAIN\user...) I tested the Authentication with other SSO frameworks with Kerberos Method and it works as expected. I'm now trying to use SSO through the NTLMHttpFilter of JCIFS. When i try to login i get the following error message: jcifs.smb.SmbException: The parameter is incorrect. jcifs.smb.SmbTransport.checkStatus(SmbTransport.java:541) jcifs.smb.SmbTransport.send(SmbTransport.java:641) jcifs.smb.SmbSession.sessionSetup(SmbSession.java:322) jcifs.smb.SmbSession.send(SmbSession.java:224) jcifs.smb.SmbTree.treeConnect(SmbTree.java:176) jcifs.smb.SmbSession.logon(SmbSession.java:153) jcifs.smb.SmbSession.logon(SmbSession.java:146) jcifs.http.NtlmHttpFilter.negotiate(NtlmHttpFilter.java:189) jcifs.http.NtlmHttpFilter.doFilter(NtlmHttpFilter.java:121) Regarding to the documentation i'm using to configure this, this is a know issue with the Group policy. It is stated there, that i have to change the Group policy "Networkaccess: lan-manager authentication level" to respond to NTLMv1 request. I have done this, but it's still not working. So what i also have to configure is the same policy on the client computer. I have to change the policy, so that the client computer sends NTLMv1. But it is always sending NTLMv2 tokens. The problem now is that i'm somehow not able to change this setting. (I already was before) because the dropdown box to choose the authentication method is "greyed out". edit: just to make this clear, this dialog is on the client-side in the "local-security policies" As you can see from this screenshot, the chosen method is "Only send NTLMv2 responses" which is the wrong setting and i'm pretty sure that this is causing the error above. My question is now, why can't i change this setting? Why is it greyd out?

  Read the article

• Clear OS always showing "Operation too slow. Less than 1 bytes/sec"

  - by Blue Gene

  Have been trying to install clear os addon but nothing is working as i am facing this error on every mirror in the .repo file. Yum install squid http://mirror2-dallas.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on http://mirror2-dallas.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. mirror2-dc.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror2-dc.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. mirror1.timburgess.net/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror1.timburgess.net/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. mirror2-houston.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror2-houston.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. mirror3-toronto.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror3-toronto.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. mirror2-dallas.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror2-dallas.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'O*peration too slow. Less than 1 bytes/sec transfered the last 30 seconds'*) Trying other mirror. mirror2-dc.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror2-dc.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. mirror1.timburgess.net/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror1.timburgess.net/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. mirror3-toronto.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror3-toronto.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. Error: failure: repodata/primary.sqlite.bz2 from clearos-core: [Errno 256] No more mirrors to try. How can i fix this.i am able to access repo through web,and it seems nothing wrong with the repo.Where can be the problem. Tried yum clean all but it also didnt help. Is there a way to fix it as i am not able to install any package in it.

  Read the article

• Unable to apt-get upgrade in ubuntu 11.10

  - by blackhole

  These are the errors shows by different client Update Manager: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/aptdaemon/worker.py", line 968, in simulate trans.unauthenticated = self._simulate_helper(trans) File "/usr/lib/python2.7/dist-packages/aptdaemon/worker.py", line 1092, in _simulate_helper return depends, self._cache.required_download, \ File "/usr/lib/python2.7/dist-packages/apt/cache.py", line 235, in required_download pm.get_archives(fetcher, self._list, self._records) SystemError: E:Method has died unexpectedly!, E:Sub-process returned an error code (100), E:Method /usr/lib/apt/methods/ did not start correctly Synaptic package Manager E: Method has died unexpectedly! E: Sub-process returned an error code (100) E: Method /usr/lib/apt/methods/ did not start correctly E: Unable to lock the download directory Command: sudo apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done The following packages will be upgraded: libfreetype6 libfreetype6-dev 2 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Failed to exec method /usr/lib/apt/methods/ E: Method has died unexpectedly! E: Sub-process returned an error code (100) E: Method /usr/lib/apt/methods/ did not start correctly Can anyone one tell me how to resolve these issues ? I have no volatile packages or anything so i am even posting the preview of my sources.list file. # deb cdrom:[Ubuntu 10.10 _Maverick Meerkat_ - Release i386 (20101007)]/ maverick main restricted # See http://help.ubuntu.com/community/UpgradeNotes for how to upgrade to # newer versions of the distribution. deb http://in.archive.ubuntu.com/ubuntu/ oneiric main restricted ## Major bug fix updates produced after the final release of the ## distribution. deb http://in.archive.ubuntu.com/ubuntu/ oneiric-updates main restricted ## N.B. software from this repository is ENTIRELY UNSUPPORTED by the Ubuntu ## team. Also, please note that software in universe WILL NOT receive any ## review or updates from the Ubuntu security team. deb http://in.archive.ubuntu.com/ubuntu/ oneiric universe deb http://in.archive.ubuntu.com/ubuntu/ oneiric-updates universe ## N.B. software from this repository is ENTIRELY UNSUPPORTED by the Ubuntu ## team, and may not be under a free licence. Please satisfy yourself as to ## your rights to use the software. Also, please note that software in ## multiverse WILL NOT receive any review or updates from the Ubuntu ## security team. deb http://in.archive.ubuntu.com/ubuntu/ oneiric multiverse deb http://in.archive.ubuntu.com/ubuntu/ oneiric-updates multiverse ## Uncomment the following two lines to add software from the 'backports' ## repository. ## N.B. software from this repository may not have been tested as ## extensively as that contained in the main release, although it includes ## newer versions of some applications which may provide useful features. ## Also, please note that software in backports WILL NOT receive any review ## or updates from the Ubuntu security team. # deb http://in.archive.ubuntu.com/ubuntu/ maverick-backports main restricted universe multiverse # deb-src http://in.archive.ubuntu.com/ubuntu/ maverick-backports main restricted universe multiverse ## Uncomment the following two lines to add software from Canonical's ## 'partner' repository. ## This software is not part of Ubuntu, but is offered by Canonical and the ## respective vendors as a service to Ubuntu users. deb http://archive.canonical.com/ubuntu oneiric partner deb-src http://archive.canonical.com/ubuntu oneiric partner ## This software is not part of Ubuntu, but is offered by third-party ## developers who want to ship their latest software. deb http://extras.ubuntu.com/ubuntu oneiric main deb-src http://extras.ubuntu.com/ubuntu oneiric main deb http://in.archive.ubuntu.com/ubuntu/ oneiric-security main restricted deb http://in.archive.ubuntu.com/ubuntu/ oneiric-security universe deb http://in.archive.ubuntu.com/ubuntu/ oneiric-security multiverse # deb http://archive.canonical.com/ lucid partner Here is the preview of my sources.list file

  Read the article

• Installing an exe with Powershell DSC Package resource gets return code 1619

  - by Jay Spang

  I'm trying to use Powershell DSC's Package resource to install an exe... Perforce's P4V to be specific. Here's my code: Configuration PerforceMachine { Node "SERVERNAME" { Package P4V { Ensure = "Present" Name = "Perforce Visual Components" Path = "\\nas\share\p4vinst64.exe" ProductId = '' Arguments = "/S /V/qn" # args for silent mode LogPath = "$env:ProgramData\p4v_install.log" } } } When running this, this is the error Powershell gives me: PowerShell provider MSFT_PackageResource failed to execute Set-TargetResource functionality with error message: The return code 1619 was not expected. Configuration is likely not correct + CategoryInfo : InvalidOperation: (:) [], CimException + FullyQualifiedErrorId : ProviderOperationExecutionFailure + PSComputerName : SERVERNAME According to documentation, return code 1619 means the MSI package couldn't be opened. However, when I manually log in to the machine and run "\\nas\share\p4vinst64.exe /S /V/qn", the install works flawlessly. Does anyone know why this is failing? Alternately, can anyone tell me how to troubleshoot this? I pasted all the error information I got from the terminal, my log file (p4v_install.log) is a 0 byte file, and there are no events in the event viewer. I don't know how to troubleshoot it any further! EDIT: I should note that I also tried using the File resource to copy the file locally, and then install it from there. Sadly, that met with the same result.

  Read the article

• DBI::DBD package not getting installed for Perl?

  - by Liju Mathew

  Hi, We are using a Perl utility to dump data from DB2 database. We installed DBI package and it is asking for DBD package also. We dont have root access and when we try to install DBD package we are getting the following error. ERROR BUILDING DB2.pm [lijumathew@intblade03 DBD-DB2-1.78]$ make make[1]: Entering directory '/home/lijumathew/lperl/perlsrc/DBD-DB2-1.78/Constants' gcc -c -I"/db2/db2tf1/sqllib/include" -D_REENTRANT -D_GNU_SOURCE -DDEBUGGING -fno-strict-aliasing -pipe -I/usr/local/include -D_LARGEFILE_SOURCE -D_FILE_OFFSET_BITS=64 -I/usr/include/gdbm -O2 -g -pipe -m32 -march=i386 -mtune=pentium4 -DVERSION=\"1.78\" -DXS_VERSION=\"1.78\" -fPIC "-I/usr/lib/perl5/5.8.5/i386-linux-thread-multi/CORE" Constants.c Running Mkbootstrap for DBD::DB2::Constants () chmod 644 Constants.bs rm -f ../blib/arch/auto/DBD/DB2/Constants/Constants.so gcc -shared -L/usr/local/lib Constants.o -o ../blib/arch/auto/DBD/DB2/Constants/Constants.so chmod 755 ../blib/arch/auto/DBD/DB2/Constants/Constants.so cp Constants.bs ../blib/arch/auto/DBD/DB2/Constants/Constants.bs chmod 644 ../blib/arch/auto/DBD/DB2/Constants/Constants.bs make[1]: Leaving directory `/home/lijumathew/lperl/perlsrc/DBD-DB2-1.78/Constants' gcc -c -I"/db2/db2tf1/sqllib/include" -I"/usr/lib/perl5/site_perl/5.8.5/i386-linux-thread-multi/auto/DBI" -I"/usr/lib/perl5/5.8.5/i386-linux-thread-multi/auto/DBI" -I"/usr/lib/perl5/vendor_perl/5.8.5/i386-linux-thread-multi/auto/DBI" -I"/usr/lib/perl5/site_perl/5.8.5/i386-linux-thread-multi/auto/DBI" -D_REENTRANT -D_GNU_SOURCE -DDEBUGGING -fno-strict-aliasing -pipe -I/usr/local/include -D_LARGEFILE_SOURCE -D_FILE_OFFSET_BITS=64 -I/usr/include/gdbm -O2 -g -pipe -m32 -march=i386 -mtune=pentium4 -DVERSION=\"1.78\" -DXS_VERSION=\"1.78\" -fPIC "-I/usr/lib/perl5/5.8.5/i386-linux-thread-multi/CORE" DB2.c In file included from DB2.h:22, from DB2.xs:7: dbdimp.h:10:22: dbivport.h: No such file or directory make: *** [DB2.o] Error 1 How to fix this? Do we need root access to resolve this? Appreciate the help in advance. Thanks, Mathew Liju

  Read the article

• josso newbie setup problems - can't use tomcat's manager page

  - by opensas

  I'm trying to setup josso on an apache tomcat server running on windows. I've installed Apache Tomcat/6.0.26 fro zip file to c:\tomcat then installed josso following the documentation at http://www.josso.org/confluence/display/JOSSO1/Quick+Start started tomcat with c:\tomcat\bin\startup.bat, and noticed the following warnings ADVERTENCIA: [SetPropertiesRule]{Server/Service/Engine/Realm} Setting property ' debug' to '1' did not find a matching property. 21/03/2010 15:55:03 org.apache.tomcat.util.digester.SetPropertiesRule begin ADVERTENCIA: [SetPropertiesRule]{Server/Service/Engine/Host/Valve} Setting prope rty 'appName' to 'josso' did not find a matching property. ... ADVERTENCIA: Unable to find required classes (javax.activation.DataHandler and j avax.mail.internet.MimeMultipart). Attachment support is disabled. ... ADVERTENCIA: Bean with key 'josso:type=SSOAuditManager' has been registered as a n MBean but has no exposed attributes or operations ... but then everything seems to work fine, the problem is I can no longer access http://localhost:8080/manager/html using user tomcat /tomcat, as configured in \conf\tomcat-users.xml (before installing josso it worked) I tried with tomcat/tomcatpwd as defined in \lib\josso-credentials.xml and even added tomcat and the manager role to \lib\josso-users.xml, with no luck... Is anybody having the same problem? how can I access tomcat's manager page? Thanks a lot saludos sas This is my config: C:\tomcat\bincatalina version Using CATALINA_BASE: "C:\tomcat" Using CATALINA_HOME: "C:\tomcat" Using CATALINA_TMPDIR: "C:\tomcat\temp" Using JRE_HOME: "c:\java" Using CLASSPATH: "C:\tomcat\bin\bootstrap.jar" Server version: Apache Tomcat/6.0.26 Server built: March 9 2010 1805 Server number: 6.0.26.0 OS Name: Windows XP OS Version: 5.1 Architecture: x86 JVM Version: 1.5.0_22-b03 JVM Vendor: Sun Microsystems Inc ps: moreover, when shutting down, I get a couple of error like this GRAVE: A web application appears to have started a thread named [JOSSOAssertionM onitor] but has failed to stop it. This is very likely to create a memory leak. 21/03/2010 15:57:06 org.apache.catalina.loader.WebappClassLoader clearReferences Threads and then tomcat's shutdown freezes at 21/03/2010 15:57:07 org.apache.coyote.ajp.AjpAprProtocol destroy INFO: Parando Coyote AJP/1.3 en ajp-8009 ps: sorry for this lengthy question...

  Read the article

• Windows-mobile app won't run after being closed by Task Manager

  - by pithyless

  I've inherited some windows-mobile code that I've been bringing up-to-date. I've come across a weird bug, and I was hoping that even though a bit vague, maybe it will spark someone's memory: Running the app (which is basically a glorified Forms app with P/Invoke gps code), I switch to the task manager, and close the app via End Task. Seems to exit fine (no errors and disappears from Task Manager). Unfortunately, the app refuses to start a second time until I reboot the phone or reinstall the CAB. What's worse: this bug is reproducible on a HTC Diamond, but works fine (ie. can run again after EndTask) on an HTC HD2. The only thing I can think of is some kind of timing race between a Dispose() and the Task Manager. Any ideas? I'm also thinking of a workaround - I do have a working "Exit Application" routine that correctly cleans up the app; can I catch the EndTask event in the c# code in order to complete a proper cleanup? Maybe I'm just missing the pain point... all ideas welcome :)

  Read the article

• package issue with ubuntu 10.10 and passenger requirements

  - by user368937

  I'm trying to get Passenger working with Ubuntu 10.10 and I'm running into a problem. It seems that the passenger installer is not recognizing the virtual package. I'm getting this error: Code: passenger-install-apache2-module ... * OpenSSL support for Ruby... not found ... And then it says, run this: * To install OpenSSL support for Ruby: Please run apt-get install libopenssl-ruby as root. When I run the above command, it refers to the libruby package: sudo apt-get install libopenssl-ruby Reading package lists... Done Building dependency tree Reading state information... Done Note, selecting 'libruby' instead of 'libopenssl-ruby' libruby is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 43 not upgraded. When I look at the details for libruby, it says it provides libopenssl-ruby: Code: Provides: libbigdecimal-ruby, libcurses-ruby, libdbm-ruby, libdl-ruby, libdrb-ruby, liberb-ruby, libgdbm-ruby, libiconv-ruby, libopenssl-ruby, libpty-ruby, libracc-runtime-ruby, libreadline-ruby, librexml-ruby, libsdbm-ruby, libstrscan-ruby, libsyslog-ruby, libtest-unit-ruby, libwebrick-ruby, libxmlrpc-ruby, libyaml-ruby, libzlib-ruby And when I rerun the passenger installer, it gives the same error: Code: passenger-install-apache2-module ... * OpenSSL support for Ruby... not found ... Let me know if you need more info. How do I fix this?

  Read the article

< Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >