Search Results

Search found 3906 results on 157 pages for 'pci express'.

Page 61/157 | < Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >

  • RHEL 5 SCSI ADPATEC

    - by Rajiv Sharma
    HI I have RHEL 5 box . and adpatec scsi card connected to it . I can see the adaptor under dsmeg | grep -i scsi dmesg | grep -i scsi SCSI subsystem initialized scsi0 : SCSI emulation for USB Mass Storage devices Type: CD-ROM ANSI SCSI revision: 00 scsi 0:0:0:0: Attached scsi generic sg0 type 5 sr0: scsi3-mmc drive: 0x/0x caddy sr 0:0:0:0: Attached scsi CD-ROM sr0 scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 aic7901: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs Loading iSCSI transport class v2.0-871. iscsi: registered transport (iser) iscsi: registered transport (cxgb3i) Broadcom NetXtreme II iSCSI Driver bnx2i v2.1.0 (Dec 06, 2009) iscsi: registered transport (bnx2i) scsi2 : Broadcom Offload iSCSI Initiator scsi3 : Broadcom Offload iSCSI Initiator iscsi: registered transport (tcp) iscsi: registered transport (be2iscsi) bnx2i: iSCSI not supported, dev=eth0 bnx2i: iSCSI not supported, dev=eth0 bnx2i: iSCSI not supported, dev=eth1 bnx2i: iSCSI not supported, dev=eth1 but cann't see under cat /proc/scsi/scsi cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: KVM Model: vmDisk-CD Rev: 0.01 Type: CD-ROM ANSI SCSI revision: 02 all st and sg modules are enable. Anyone please help me thanks advance Rajiv

    Read the article

  • SQLAuthority News – TechEd India – April 12-14, 2010 Bangalore – An Unforgettable Experience – An Op

    - by pinaldave
    TechEd India was one of the largest Technology events in India led by Microsoft. This event was attended by more than 3,000 technology enthusiasts, making it one of the most well-organized events of the year. Though I attempted to attend almost all the technology events here, I have not seen any bigger or better event in Indian subcontinents other than this. There are 21 Technical Tracks at Tech·Ed India 2010 that span more than 745 learning opportunities. I was fortunate enough to be a part of this whole event as a speaker and a delegate, as well. TechEd India Speaker Badge and A Token of Lifetime Hotel Selection I presented three different sessions at TechEd India and was also a part of panel discussion. (The details of the sessions are given at the end of this blog post.) Due to extensive traveling, I stay away from my family occasionally. For this reason, I took my wife – Nupur and daughter Shaivi (8 months old) to the event along with me. We stayed at the same hotel where the event was organized so as to maximize my time bonding with my family and to have more time in networking with technology community, at the same time. The hotel Lalit Ashok is the largest and most luxurious venue one can find in Bangalore, located in the middle of the city. The cost of the hotel was a bit pricey, but looking at all the advantages, I had decided to ask for a booking there. Hotel Lalit Ashok Nupur Dave and Shaivi Dave Arrival Day – DAY 0 – April 11, 2010 I reached the event a day earlier, and that was one wise decision for I was able to relax a bit and go over my presentation for the next day’s course. I am a kind of person who likes to get everything ready ahead of time. I was also able to enjoy a pleasant evening with several Microsoft employees and my family friends. I even checked out the location where I would be doing presentations the next day. I was fortunate enough to meet Bijoy Singhal from Microsoft who helped me out with a few of the logistics issues that occured the day before. I was not aware of the fact that the very next day he was going to be “The Man” of the TechEd 2010 event. Vinod Kumar from Microsoft was really very kind as he talked to me regarding my subsequent session. He gave me some suggestions which were really helpful that I was able to incorporate them during my presentation. Finally, I was able to meet Abhishek Kant from Microsoft; his valuable suggestions and unlimited passion have inspired many people like me to work with the Community. Pradipta from Microsoft was also around, being extremely busy with logistics; however, in those busy times, he did find some good spare time to have a chat with me and the other Community leaders. I also met Harish Ranganathan and Sachin Rathi, both from Microsoft. It was so interesting to listen to both of them talking about SharePoint. I just have no words to express my overwhelmed spirit because of all these passionate young guys - Pradipta,Vinod, Bijoy, Harish, Sachin and Ahishek (of course!). Map of TechEd India 2010 Event Day 1 – April 12, 2010 From morning until night time, today was truly a very busy day for me. I had two presentations and one panel discussion for the day. Needless to say, I had a few meetings to attend as well. The day started with a keynote from S. Somaseger where he announced the launch of Visual Studio 2010. The keynote area was really eye-catching because of the very large, bigger-than- life uniform screen. This was truly one to show. The title music of the keynote was very interesting and it featured Bijoy Singhal as the model. It was interesting to talk to him afterwards, when we laughed at jokes together about his modeling assignment. TechEd India Keynote Opening Featuring Bijoy TechEd India 2010 Keynote – S. Somasegar Time: 11:15pm – 11:45pm Session 1: True Lies of SQL Server – SQL Myth Buster Following the excellent keynote, I had my very first session on the subject of SQL Server Myth Buster. At first, I was a bit nervous as right after the keynote, for this was my very first session and during my presentation I saw lots of Microsoft Product Team members. Well, it really went well and I had a really good discussion with attendees of the session. I felt that a well begin was half-done and my confidence was regained. Right after the session, I met a few of my Community friends and had meaningful discussions with them on many subjects. The abstract of the session is as follows: In this 30-minute demo session, I am going to briefly demonstrate few SQL Server Myths and their resolutions as I back them up with some demo. This demo presentation is a must-attend for all developers and administrators who would come to the event. This is going to be a very quick yet fun session. Pinal Presenting session at TechEd India 2010 Time: 1:00 PM – 2:00 PM Lunch with Somasegar After the session I went to see my daughter, and then I headed right away to the lunch with S. Somasegar – the keynote speaker and senior vice president of the Developer Division at Microsoft. I really thank to Abhishek who made it possible for us. Because of his efforts, all the MVPs had the opportunity to meet such a legendary person and had to talk with them on Microsoft Technology. Though Somasegar is currently holding such a high position in Microsoft, he is very polite and a real gentleman, and how I wish that everybody in industry is like him. Believe me, if you spread love and kindness, then that is what you will receive back. As soon as lunch time was over, I ran to the session hall as my second presentation was about to start. Time: 2:30pm – 3:30pm Session 2: Master Data Services in Microsoft SQL Server 2008 R2 Business Intelligence is a subject which was widely talked about at TechEd. Everybody was interested in this subject, and I did not excuse myself from this great concept as well. I consider myself fortunate as I was presenting on the subject of Master Data Services at TechEd. When I had initially learned this subject, I had a bit of confusion about the usage of this tool. Later on, I decided that I would tackle about how we all developers and DBAs are not able to understand something so simple such as this, and even worst, creating confusion about the technology. During system designing, it is very important to have a reference material or master lookup tables. Well, I talked about the same subject and presented the session keeping that as my center talk. The session went very well and I received lots of interesting questions. I got many compliments for talking about this subject on the real-life scenario. I really thank Rushabh Mehta (CEO, Solid Quality Mentors India) for his supportive suggestions that helped me prepare the slide deck, as well as the subject. Pinal Presenting session at TechEd India 2010 The abstract of the session is as follows: SQL Server Master Data Services will ship with SQL Server 2008 R2 and will improve Microsoft’s platform appeal. This session provides an in-depth demonstration of MDS features and highlights important usage scenarios. Master Data Services enables consistent decision-making process by allowing you to create, manage and propagate changes from a single master view of your business entities. Also, MDS – Master Data-hub which is a vital component, helps ensure the consistency of reporting across systems and deliver faster and more accurate results across the enterprise. We will talk about establishing the basis for a centralized approach to defining, deploying, and managing master data in the enterprise. Pinal Presenting session at TechEd India 2010 The day was still not over for me. I had ran into several friends but we were not able keep our enthusiasm under control about all the rumors saying that SQL Server 2008 R2 was about to be launched tomorrow in the keynote. I then ran to my third and final technical event for the day- a panel discussion with the top technologies of India. Time: 5:00pm – 6:00pm Panel Discussion: Harness the power of Web – SEO and Technical Blogging As I have delivered two technical sessions by this time, I was a bit tired but  not less enthusiastic when I had to talk about Blog and Technology. We discussed many different topics there. I told them that the most important aspect for any blog is its content. We discussed in depth the issues with plagiarism and how to avoid it. Another topic of discussion was how we technology bloggers can create awareness in the Community about what the right kind of blogging is and what morally and technically wrong acts are. A couple of questions were raised about what type of liberty a person can have in terms of writing blogs. Well, it was generically agreed that a blog is mainly a representation of our ideas and thoughts; it should not be governed by external entities. As long as one is writing what they really want to say, but not providing incorrect information or not practicing plagiarism, a blogger should be allowed to express himself. This panel discussion was supposed to be over in an hour, but the interest of the participants was remarkable and so it was extended for 30 minutes more. Finally, we decided to bring to a close the discussion and agreed that we will continue the topic next year. TechEd India Panel Discussion on Web, Technology and SEO Surprisingly, the day was just beginning after doing all of these. By this time, I have almost met all the MVP who arrived at the event, as well as many Microsoft employees. There were lots of Community folks present, too. I decided that I would go to meet several friends from the Community and continue to communicate with me on SQLAuthority.com. I also met Abhishek Baxi and had a good talk with him regarding Win Mobile and Twitter. He also took a very quick video of me wherein I spoke in my mother’s tongue, Gujarati. It was funny that I talked in Gujarati almost all the day, but when I was talking in the interview I could not find the right Gujarati words to speak. I think we all think in English when we think about Technology, so as to address universality. After meeting them, I headed towards the Speakers’ Dinner. Time: 8:00 PM – onwards Speakers Dinner The Speakers’ dinner was indeed a wonderful opportunity for all the speakers to get together and relax. We talked so many different things, from XBOX to Hindi Movies, and from SQL to Samosas. I just could not express how much fun I had. After a long evening, when I returned tmy room and met Shaivi, I just felt instantly relaxed. Kids are really gifts from God. Today was a really long but exciting day. So many things happened in just one day: Visual Studio Lanch, lunch with Somasegar, 2 technical sessions, 1 panel discussion, community leaders meeting, speakers dinner and, last but not leas,t playing with my child! A perfect day! Day 2 – April 13, 2010 Today started with a bang with the excellent keynote by Kamal Hathi who launched SQL Server 2008 R2 in India and demonstrated the power of PowerPivot to all of us. 101 Million Rows in Excel brought lots of applause from the audience. Kamal Hathi Presenting Keynote at TechEd India 2010 The day was a bit easier one for me. I had no sessions today and no events planned. I had a few meetings planned for the second day of the event. I sat in the speaker’s lounge for half a day and met many people there. I attended nearly 9 different meetings today. The subjects of the meetings were very different. Here is a list of the topics of the Community-related meetings: SQL PASS and its involvement in India and subcontinents How to start community blogging Forums and developing aptitude towards technology Ahmedabad/Gandhinagar User Groups and their developments SharePoint and SQL Business Meeting – a client meeting Business Meeting – a potential performance tuning project Business Meeting – Solid Quality Mentors (SolidQ) And family friends Pinal Dave at TechEd India The day passed by so quickly during this meeting. In the evening, I headed to Partners Expo with friends and checked out few of the booths. I really wanted to talk about some of the products, but due to the freebies there was so much crowd that I finally decided to just take the contact details of the partner. I will now start sending them with my queries and, hopefully, I will have my questions answered. Nupur and Shaivi had also one meeting to attend; it was with our family friend Vijay Raj. Vijay is also a person who loves Technology and loves it more than anybody. I see him growing and learning every day, but still remaining as a ‘human’. I believe that if someone acquires as much knowledge as him, that person will become either a computer or cyborg. Here, Vijay is still a kind gentleman and is able to stay as our close family friend. Shaivi was really happy to play with Uncle Vijay. Pinal Dave and Vijay Raj Renuka Prasad, a Microsoft MVP, impressed me with his passion and knowledge of SQL. Every time he gives me credit for his success, I believe that he is very humble. He has way more certifications than me and has worked many more years with SQL compared to me. He is an excellent photographer as well. Most of the photos in this blog post have been taken by him. I told him if ever he wants to do a part time job, he can do the photography very well. Pinal Dave and Renuka Prasad I also met L Srividya from Microsoft, whom I was looking forward to meet. She is a bundle of knowledge that everyone would surely learn a lot from her. I was able to get a few minutes from her and well, I felt confident. She enlightened me with SQL Server BI concepts, domain management and SQL Server security and few other interesting details. I also had a wonderful time talking about SharePoint with fellow Solid Quality Mentor Joy Rathnayake. He is very passionate about SharePoint but when you talk .NET and SQL with him, he is still overwhelmingly knowledgeable. In fact, while talking to him, I figured out that the recent training he delivered was on SQL Server 2008 R2. I told him a joke that it hurts my ego as he is more popular now in SQL training and consulting than me. I am sure all of you agree that working with good people is a gift from God. I am fortunate enough to work with the best of the best Industry experts. It was a great pleasure to hang out with my Community friends – Ahswin Kini, HimaBindu Vejella, Vasudev G, Suprotim Agrawal, Dhananjay, Vikram Pendse, Mahesh Dhola, Mahesh Mitkari,  Manu Zacharia, Shobhan, Hardik Shah, Ashish Mohta, Manan, Subodh Sohani and Sanjay Shetty (of course!) .  (Please let me know if I have met you at the event and forgot your name to list here). Time: 8:00 PM – onwards Community Leaders Dinner After lots of meetings, I headed towards the Community Leaders dinner meeting and met almost all the folks I met in morning. The discussion was almost the same but the real good thing was that we were enjoying it. The food was really good. Nupur was invited in the event, but Shaivi could not come. When Nupur tried to enter the event, she was stopped as Shaivi did not have the pass to enter the dinner. Nupur expressed that Shaivi is only 8 months old and does not eat outside food as well and could not stay by herself at this age, but the door keeper did not agree and asked that without the entry details Shaivi could not go in, but Nupur could. Nupur called me on phone and asked me to help her out. By the time, I was outside; the organizer of the event reached to the door and happily approved Shaivi to join the party. Once in the party, Shaivi had lots of fun meeting so many people. Shaivi Dave and Abhishek Kant Dean Guida (Infragistics President and CEO) and Pinal Dave (SQLAuthority.com) Day 3 – April 14, 2010 Though, it was last day, I was very much excited today as I was about to present my very favorite session. Query Optimization and Performance Tuning is my domain expertise and I make my leaving by consulting and training the same. Today’s session was on the same subject and as an additional twist, another subject about Spatial Database was presented. I was always intrigued with Spatial Database and I have enjoyed learning about it; however, I have never thought about Spatial Indexing before it was decided that I will do this session. I really thank Solid Quality Mentor Dr. Greg Low for his assistance in helping me prepare the slide deck and also review the content. Furthermore, today was really what I call my ‘learning day’ . So far I had not attended any session in TechEd and I felt a bit down for that. Everybody spends their valuable time & money to learn something new and exciting in TechEd and I had not attended a single session at the moment thinking that it was already last day of the event. I did have a plan for the day and I attended two technical sessions before my session of spatial database. I attended 2 sessions of Vinod Kumar. Vinod is a natural storyteller and there was no doubt that his sessions would be jam-packed. People attended his sessions simply because Vinod is syhe speaker. He did not have a single time disappointed audience; he is truly a good speaker. He knows his stuff very well. I personally do not think that in India he can be compared to anyone for SQL. Time: 12:30pm-1:30pm SQL Server Query Optimization, Execution and Debugging Query Performance I really had a fun time attending this session. Vinod made this session very interactive. The entire audience really got into the presentation and started participating in the event. Vinod was presenting a small problem with Query Tuning, which any developer would have encountered and solved with their help in such a fashion that a developer feels he or she have already resolved it. In one question, I was the only one who was ready to answer and Vinod told me in a light tone that I am now allowed to answer it! The audience really found it very amusing. There was a huge crowd around Vinod after the session. Vinod – A master storyteller! Time: 3:45pm-4:45pm Data Recovery / consistency with CheckDB This session was much heavier than the earlier one, and I must say this is my most favorite session I EVER attended in India. In this TechEd I have only attended two sessions, but in my career, I have attended numerous technical sessions not only in India, but all over the world. This session had taken my breath away. One by one, Vinod took the different databases, and started to corrupt them in different ways. Each database has some unique ways to get corrupted. Once that was done, Vinod started to show the DBCC CEHCKDB and demonstrated how it can solve your problem. He finally fixed all the databases with this single tool. I do have a good knowledge of this subject, but let me honestly admit that I have learned a lot from this session. I enjoyed and cheered during this session along with other attendees. I had total satisfaction that, just like everyone, I took advantage of the event and learned something. I am now TECHnically EDucated. Pinal Dave and Vinod Kumar After two very interactive and informative SQL Sessions from Vinod Kumar, the next turn me presenting on Spatial Database and Indexing. I got once again nervous but Vinod told me to stay natural and do my presentation. Well, once I got a huge stage with a total of four projectors and a large crowd, I felt better. Time: 5:00pm-6:00pm Session 3: Developing with SQL Server Spatial and Deep Dive into Spatial Indexing Pinal Presenting session at TechEd India 2010 Pinal Presenting session at TechEd India 2010 I kicked off this session with Michael J Swart‘s beautiful spatial image. This session was the last one for the day but, to my surprise, I had more than 200+ attendees. Slowly, the rain was starting outside and I was worried that the hall would not be full; despite this, there was not a single seat available in the first five minutes of the session. Thanks to all of you for attending my presentation. I had demonstrated the map of world (and India) and quickly explained what  Geographic and Geometry data types in Spatial Database are. This session had interesting story of Indexing and Comparison, as well as how different traditional indexes are from spatial indexing. Pinal Presenting session at TechEd India 2010 Due to the heavy rain during this event, the power went off for about 22 minutes (just an accident – nobodies fault). During these minutes, there were no audio, no video and no light. I continued to address the mass of 200+ people without any audio device and PowerPoint. I must thank the audience because not a single person left from the session. They all stayed in their place, some moved closure to listen to me properly. I noticed that the curiosity and eagerness to learn new things was at the peak even though it was the very last session of the TechEd. Everybody wanted get the maximum knowledge out of this whole event. I was touched by the support from audience. They listened and participated in my session even without any kinds of technology (no ppt, no mike, no AC, nothing). During these 22 minutes, I had completed my theory verbally. Pinal Presenting session at TechEd India 2010 After a while, we got the projector back online and we continued with some exciting demos. Many thanks to Microsoft people who worked energetically in background to get the backup power for project up. I had a very interesting demo wherein I overlaid Bangalore and Hyderabad on the India Map and find their aerial distance between them. After finding the aerial distance, we browsed online and found that SQL Server estimates the exact aerial distance between these two cities, as compared to the factual distance. There was a huge applause from the crowd on the subject that SQL Server takes into the count of the curvature of the earth and finds the precise distances based on details. During the process of finding the distance, I demonstrated a few examples of the indexes where I expressed how one can use those indexes to find these distances and how they can improve the performance of similar query. I also demonstrated few examples wherein we were able to see in which data type the Index is most useful. We finished the demos with a few more internal stuff. Pinal Presenting session at TechEd India 2010 Despite all issues, I was mostly satisfied with my presentation. I think it was the best session I have ever presented at any conference. There was no help from Technology for a while, but I still got lots of appreciation at the end. When we ended the session, the applause from the audience was so loud that for a moment, the rain was not audible. I was truly moved by the dedication of the Technology enthusiasts. Pinal Dave After Presenting session at TechEd India 2010 The abstract of the session is as follows: The Microsoft SQL Server 2008 delivers new spatial data types that enable you to consume, use, and extend location-based data through spatial-enabled applications. Attend this session to learn how to use spatial functionality in next version of SQL Server to build and optimize spatial queries. This session outlines the new geography data type to store geodetic spatial data and perform operations on it, use the new geometry data type to store planar spatial data and perform operations on it, take advantage of new spatial indexes for high performance queries, use the new spatial results tab to quickly and easily view spatial query results directly from within Management Studio, extend spatial data capabilities by building or integrating location-enabled applications through support for spatial standards and specifications and much more. Time: 8:00 PM – onwards Dinner by Sponsors After the lively session during the day, there was another dinner party courtesy of one of the sponsors of TechEd. All the MVPs and several Community leaders were present at the dinner. I would like to express my gratitude to Abhishek Kant for organizing this wonderful event for us. It was a blast and really relaxing in all angles. We all stayed there for a long time and talked about our sweet and unforgettable memories of the event. Pinal Dave and Bijoy Singhal It was really one wonderful event. After writing this much, I say that I have no words to express about how much I enjoyed TechEd. However, it is true that I shared with you only 1% of the total activities I have done at the event. There were so many people I have met, yet were not mentioned here although I wanted to write their names here, too . Anyway, I have learned so many things and up until now, I am not able to get over all the fun I had in this event. Pinal Dave at TechEd India 2010 The Next Days – April 15, 2010 – till today I am still not able to get my mind out of the whole experience I had at TechEd India 2010. It was like a whole Microsoft Family working together to celebrate a happy occasion. TechEd India – Truly An Unforgettable Experience! Reference : Pinal Dave (http://blog.SQLAuthority.com) Filed under: About Me, MVP, Pinal Dave, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQLAuthority Author Visit, SQLAuthority News, SQLServer, T SQL, Technology Tagged: TechEd, TechEdIn

    Read the article

  • SQLAuthority News – TechEd India – April 12-14, 2010 Bangalore – An Unforgettable Experience – An Op

    - by pinaldave
    TechEd India was one of the largest Technology events in India led by Microsoft. This event was attended by more than 3,000 technology enthusiasts, making it one of the most well-organized events of the year. Though I attempted to attend almost all the technology events here, I have not seen any bigger or better event in Indian subcontinents other than this. There are 21 Technical Tracks at Tech·Ed India 2010 that span more than 745 learning opportunities. I was fortunate enough to be a part of this whole event as a speaker and a delegate, as well. TechEd India Speaker Badge and A Token of Lifetime Hotel Selection I presented three different sessions at TechEd India and was also a part of panel discussion. (The details of the sessions are given at the end of this blog post.) Due to extensive traveling, I stay away from my family occasionally. For this reason, I took my wife – Nupur and daughter Shaivi (8 months old) to the event along with me. We stayed at the same hotel where the event was organized so as to maximize my time bonding with my family and to have more time in networking with technology community, at the same time. The hotel Lalit Ashok is the largest and most luxurious venue one can find in Bangalore, located in the middle of the city. The cost of the hotel was a bit pricey, but looking at all the advantages, I had decided to ask for a booking there. Hotel Lalit Ashok Nupur Dave and Shaivi Dave Arrival Day – DAY 0 – April 11, 2010 I reached the event a day earlier, and that was one wise decision for I was able to relax a bit and go over my presentation for the next day’s course. I am a kind of person who likes to get everything ready ahead of time. I was also able to enjoy a pleasant evening with several Microsoft employees and my family friends. I even checked out the location where I would be doing presentations the next day. I was fortunate enough to meet Bijoy Singhal from Microsoft who helped me out with a few of the logistics issues that occured the day before. I was not aware of the fact that the very next day he was going to be “The Man” of the TechEd 2010 event. Vinod Kumar from Microsoft was really very kind as he talked to me regarding my subsequent session. He gave me some suggestions which were really helpful that I was able to incorporate them during my presentation. Finally, I was able to meet Abhishek Kant from Microsoft; his valuable suggestions and unlimited passion have inspired many people like me to work with the Community. Pradipta from Microsoft was also around, being extremely busy with logistics; however, in those busy times, he did find some good spare time to have a chat with me and the other Community leaders. I also met Harish Ranganathan and Sachin Rathi, both from Microsoft. It was so interesting to listen to both of them talking about SharePoint. I just have no words to express my overwhelmed spirit because of all these passionate young guys - Pradipta,Vinod, Bijoy, Harish, Sachin and Ahishek (of course!). Map of TechEd India 2010 Event Day 1 – April 12, 2010 From morning until night time, today was truly a very busy day for me. I had two presentations and one panel discussion for the day. Needless to say, I had a few meetings to attend as well. The day started with a keynote from S. Somaseger where he announced the launch of Visual Studio 2010. The keynote area was really eye-catching because of the very large, bigger-than- life uniform screen. This was truly one to show. The title music of the keynote was very interesting and it featured Bijoy Singhal as the model. It was interesting to talk to him afterwards, when we laughed at jokes together about his modeling assignment. TechEd India Keynote Opening Featuring Bijoy TechEd India 2010 Keynote – S. Somasegar Time: 11:15pm – 11:45pm Session 1: True Lies of SQL Server – SQL Myth Buster Following the excellent keynote, I had my very first session on the subject of SQL Server Myth Buster. At first, I was a bit nervous as right after the keynote, for this was my very first session and during my presentation I saw lots of Microsoft Product Team members. Well, it really went well and I had a really good discussion with attendees of the session. I felt that a well begin was half-done and my confidence was regained. Right after the session, I met a few of my Community friends and had meaningful discussions with them on many subjects. The abstract of the session is as follows: In this 30-minute demo session, I am going to briefly demonstrate few SQL Server Myths and their resolutions as I back them up with some demo. This demo presentation is a must-attend for all developers and administrators who would come to the event. This is going to be a very quick yet fun session. Pinal Presenting session at TechEd India 2010 Time: 1:00 PM – 2:00 PM Lunch with Somasegar After the session I went to see my daughter, and then I headed right away to the lunch with S. Somasegar – the keynote speaker and senior vice president of the Developer Division at Microsoft. I really thank to Abhishek who made it possible for us. Because of his efforts, all the MVPs had the opportunity to meet such a legendary person and had to talk with them on Microsoft Technology. Though Somasegar is currently holding such a high position in Microsoft, he is very polite and a real gentleman, and how I wish that everybody in industry is like him. Believe me, if you spread love and kindness, then that is what you will receive back. As soon as lunch time was over, I ran to the session hall as my second presentation was about to start. Time: 2:30pm – 3:30pm Session 2: Master Data Services in Microsoft SQL Server 2008 R2 Business Intelligence is a subject which was widely talked about at TechEd. Everybody was interested in this subject, and I did not excuse myself from this great concept as well. I consider myself fortunate as I was presenting on the subject of Master Data Services at TechEd. When I had initially learned this subject, I had a bit of confusion about the usage of this tool. Later on, I decided that I would tackle about how we all developers and DBAs are not able to understand something so simple such as this, and even worst, creating confusion about the technology. During system designing, it is very important to have a reference material or master lookup tables. Well, I talked about the same subject and presented the session keeping that as my center talk. The session went very well and I received lots of interesting questions. I got many compliments for talking about this subject on the real-life scenario. I really thank Rushabh Mehta (CEO, Solid Quality Mentors India) for his supportive suggestions that helped me prepare the slide deck, as well as the subject. Pinal Presenting session at TechEd India 2010 The abstract of the session is as follows: SQL Server Master Data Services will ship with SQL Server 2008 R2 and will improve Microsoft’s platform appeal. This session provides an in-depth demonstration of MDS features and highlights important usage scenarios. Master Data Services enables consistent decision-making process by allowing you to create, manage and propagate changes from a single master view of your business entities. Also, MDS – Master Data-hub which is a vital component, helps ensure the consistency of reporting across systems and deliver faster and more accurate results across the enterprise. We will talk about establishing the basis for a centralized approach to defining, deploying, and managing master data in the enterprise. Pinal Presenting session at TechEd India 2010 The day was still not over for me. I had ran into several friends but we were not able keep our enthusiasm under control about all the rumors saying that SQL Server 2008 R2 was about to be launched tomorrow in the keynote. I then ran to my third and final technical event for the day- a panel discussion with the top technologies of India. Time: 5:00pm – 6:00pm Panel Discussion: Harness the power of Web – SEO and Technical Blogging As I have delivered two technical sessions by this time, I was a bit tired but  not less enthusiastic when I had to talk about Blog and Technology. We discussed many different topics there. I told them that the most important aspect for any blog is its content. We discussed in depth the issues with plagiarism and how to avoid it. Another topic of discussion was how we technology bloggers can create awareness in the Community about what the right kind of blogging is and what morally and technically wrong acts are. A couple of questions were raised about what type of liberty a person can have in terms of writing blogs. Well, it was generically agreed that a blog is mainly a representation of our ideas and thoughts; it should not be governed by external entities. As long as one is writing what they really want to say, but not providing incorrect information or not practicing plagiarism, a blogger should be allowed to express himself. This panel discussion was supposed to be over in an hour, but the interest of the participants was remarkable and so it was extended for 30 minutes more. Finally, we decided to bring to a close the discussion and agreed that we will continue the topic next year. TechEd India Panel Discussion on Web, Technology and SEO Surprisingly, the day was just beginning after doing all of these. By this time, I have almost met all the MVP who arrived at the event, as well as many Microsoft employees. There were lots of Community folks present, too. I decided that I would go to meet several friends from the Community and continue to communicate with me on SQLAuthority.com. I also met Abhishek Baxi and had a good talk with him regarding Win Mobile and Twitter. He also took a very quick video of me wherein I spoke in my mother’s tongue, Gujarati. It was funny that I talked in Gujarati almost all the day, but when I was talking in the interview I could not find the right Gujarati words to speak. I think we all think in English when we think about Technology, so as to address universality. After meeting them, I headed towards the Speakers’ Dinner. Time: 8:00 PM – onwards Speakers Dinner The Speakers’ dinner was indeed a wonderful opportunity for all the speakers to get together and relax. We talked so many different things, from XBOX to Hindi Movies, and from SQL to Samosas. I just could not express how much fun I had. After a long evening, when I returned tmy room and met Shaivi, I just felt instantly relaxed. Kids are really gifts from God. Today was a really long but exciting day. So many things happened in just one day: Visual Studio Lanch, lunch with Somasegar, 2 technical sessions, 1 panel discussion, community leaders meeting, speakers dinner and, last but not leas,t playing with my child! A perfect day! Day 2 – April 13, 2010 Today started with a bang with the excellent keynote by Kamal Hathi who launched SQL Server 2008 R2 in India and demonstrated the power of PowerPivot to all of us. 101 Million Rows in Excel brought lots of applause from the audience. Kamal Hathi Presenting Keynote at TechEd India 2010 The day was a bit easier one for me. I had no sessions today and no events planned. I had a few meetings planned for the second day of the event. I sat in the speaker’s lounge for half a day and met many people there. I attended nearly 9 different meetings today. The subjects of the meetings were very different. Here is a list of the topics of the Community-related meetings: SQL PASS and its involvement in India and subcontinents How to start community blogging Forums and developing aptitude towards technology Ahmedabad/Gandhinagar User Groups and their developments SharePoint and SQL Business Meeting – a client meeting Business Meeting – a potential performance tuning project Business Meeting – Solid Quality Mentors (SolidQ) And family friends Pinal Dave at TechEd India The day passed by so quickly during this meeting. In the evening, I headed to Partners Expo with friends and checked out few of the booths. I really wanted to talk about some of the products, but due to the freebies there was so much crowd that I finally decided to just take the contact details of the partner. I will now start sending them with my queries and, hopefully, I will have my questions answered. Nupur and Shaivi had also one meeting to attend; it was with our family friend Vijay Raj. Vijay is also a person who loves Technology and loves it more than anybody. I see him growing and learning every day, but still remaining as a ‘human’. I believe that if someone acquires as much knowledge as him, that person will become either a computer or cyborg. Here, Vijay is still a kind gentleman and is able to stay as our close family friend. Shaivi was really happy to play with Uncle Vijay. Pinal Dave and Vijay Raj Renuka Prasad, a Microsoft MVP, impressed me with his passion and knowledge of SQL. Every time he gives me credit for his success, I believe that he is very humble. He has way more certifications than me and has worked many more years with SQL compared to me. He is an excellent photographer as well. Most of the photos in this blog post have been taken by him. I told him if ever he wants to do a part time job, he can do the photography very well. Pinal Dave and Renuka Prasad I also met L Srividya from Microsoft, whom I was looking forward to meet. She is a bundle of knowledge that everyone would surely learn a lot from her. I was able to get a few minutes from her and well, I felt confident. She enlightened me with SQL Server BI concepts, domain management and SQL Server security and few other interesting details. I also had a wonderful time talking about SharePoint with fellow Solid Quality Mentor Joy Rathnayake. He is very passionate about SharePoint but when you talk .NET and SQL with him, he is still overwhelmingly knowledgeable. In fact, while talking to him, I figured out that the recent training he delivered was on SQL Server 2008 R2. I told him a joke that it hurts my ego as he is more popular now in SQL training and consulting than me. I am sure all of you agree that working with good people is a gift from God. I am fortunate enough to work with the best of the best Industry experts. It was a great pleasure to hang out with my Community friends – Ahswin Kini, HimaBindu Vejella, Vasudev G, Suprotim Agrawal, Dhananjay, Vikram Pendse, Mahesh Dhola, Mahesh Mitkari,  Manu Zacharia, Shobhan, Hardik Shah, Ashish Mohta, Manan, Subodh Sohani and Sanjay Shetty (of course!) .  (Please let me know if I have met you at the event and forgot your name to list here). Time: 8:00 PM – onwards Community Leaders Dinner After lots of meetings, I headed towards the Community Leaders dinner meeting and met almost all the folks I met in morning. The discussion was almost the same but the real good thing was that we were enjoying it. The food was really good. Nupur was invited in the event, but Shaivi could not come. When Nupur tried to enter the event, she was stopped as Shaivi did not have the pass to enter the dinner. Nupur expressed that Shaivi is only 8 months old and does not eat outside food as well and could not stay by herself at this age, but the door keeper did not agree and asked that without the entry details Shaivi could not go in, but Nupur could. Nupur called me on phone and asked me to help her out. By the time, I was outside; the organizer of the event reached to the door and happily approved Shaivi to join the party. Once in the party, Shaivi had lots of fun meeting so many people. Shaivi Dave and Abhishek Kant Dean Guida (Infragistics President and CEO) and Pinal Dave (SQLAuthority.com) Day 3 – April 14, 2010 Though, it was last day, I was very much excited today as I was about to present my very favorite session. Query Optimization and Performance Tuning is my domain expertise and I make my leaving by consulting and training the same. Today’s session was on the same subject and as an additional twist, another subject about Spatial Database was presented. I was always intrigued with Spatial Database and I have enjoyed learning about it; however, I have never thought about Spatial Indexing before it was decided that I will do this session. I really thank Solid Quality Mentor Dr. Greg Low for his assistance in helping me prepare the slide deck and also review the content. Furthermore, today was really what I call my ‘learning day’ . So far I had not attended any session in TechEd and I felt a bit down for that. Everybody spends their valuable time & money to learn something new and exciting in TechEd and I had not attended a single session at the moment thinking that it was already last day of the event. I did have a plan for the day and I attended two technical sessions before my session of spatial database. I attended 2 sessions of Vinod Kumar. Vinod is a natural storyteller and there was no doubt that his sessions would be jam-packed. People attended his sessions simply because Vinod is syhe speaker. He did not have a single time disappointed audience; he is truly a good speaker. He knows his stuff very well. I personally do not think that in India he can be compared to anyone for SQL. Time: 12:30pm-1:30pm SQL Server Query Optimization, Execution and Debugging Query Performance I really had a fun time attending this session. Vinod made this session very interactive. The entire audience really got into the presentation and started participating in the event. Vinod was presenting a small problem with Query Tuning, which any developer would have encountered and solved with their help in such a fashion that a developer feels he or she have already resolved it. In one question, I was the only one who was ready to answer and Vinod told me in a light tone that I am now allowed to answer it! The audience really found it very amusing. There was a huge crowd around Vinod after the session. Vinod – A master storyteller! Time: 3:45pm-4:45pm Data Recovery / consistency with CheckDB This session was much heavier than the earlier one, and I must say this is my most favorite session I EVER attended in India. In this TechEd I have only attended two sessions, but in my career, I have attended numerous technical sessions not only in India, but all over the world. This session had taken my breath away. One by one, Vinod took the different databases, and started to corrupt them in different ways. Each database has some unique ways to get corrupted. Once that was done, Vinod started to show the DBCC CEHCKDB and demonstrated how it can solve your problem. He finally fixed all the databases with this single tool. I do have a good knowledge of this subject, but let me honestly admit that I have learned a lot from this session. I enjoyed and cheered during this session along with other attendees. I had total satisfaction that, just like everyone, I took advantage of the event and learned something. I am now TECHnically EDucated. Pinal Dave and Vinod Kumar After two very interactive and informative SQL Sessions from Vinod Kumar, the next turn me presenting on Spatial Database and Indexing. I got once again nervous but Vinod told me to stay natural and do my presentation. Well, once I got a huge stage with a total of four projectors and a large crowd, I felt better. Time: 5:00pm-6:00pm Session 3: Developing with SQL Server Spatial and Deep Dive into Spatial Indexing Pinal Presenting session at TechEd India 2010 Pinal Presenting session at TechEd India 2010 I kicked off this session with Michael J Swart‘s beautiful spatial image. This session was the last one for the day but, to my surprise, I had more than 200+ attendees. Slowly, the rain was starting outside and I was worried that the hall would not be full; despite this, there was not a single seat available in the first five minutes of the session. Thanks to all of you for attending my presentation. I had demonstrated the map of world (and India) and quickly explained what  Geographic and Geometry data types in Spatial Database are. This session had interesting story of Indexing and Comparison, as well as how different traditional indexes are from spatial indexing. Pinal Presenting session at TechEd India 2010 Due to the heavy rain during this event, the power went off for about 22 minutes (just an accident – nobodies fault). During these minutes, there were no audio, no video and no light. I continued to address the mass of 200+ people without any audio device and PowerPoint. I must thank the audience because not a single person left from the session. They all stayed in their place, some moved closure to listen to me properly. I noticed that the curiosity and eagerness to learn new things was at the peak even though it was the very last session of the TechEd. Everybody wanted get the maximum knowledge out of this whole event. I was touched by the support from audience. They listened and participated in my session even without any kinds of technology (no ppt, no mike, no AC, nothing). During these 22 minutes, I had completed my theory verbally. Pinal Presenting session at TechEd India 2010 After a while, we got the projector back online and we continued with some exciting demos. Many thanks to Microsoft people who worked energetically in background to get the backup power for project up. I had a very interesting demo wherein I overlaid Bangalore and Hyderabad on the India Map and find their aerial distance between them. After finding the aerial distance, we browsed online and found that SQL Server estimates the exact aerial distance between these two cities, as compared to the factual distance. There was a huge applause from the crowd on the subject that SQL Server takes into the count of the curvature of the earth and finds the precise distances based on details. During the process of finding the distance, I demonstrated a few examples of the indexes where I expressed how one can use those indexes to find these distances and how they can improve the performance of similar query. I also demonstrated few examples wherein we were able to see in which data type the Index is most useful. We finished the demos with a few more internal stuff. Pinal Presenting session at TechEd India 2010 Despite all issues, I was mostly satisfied with my presentation. I think it was the best session I have ever presented at any conference. There was no help from Technology for a while, but I still got lots of appreciation at the end. When we ended the session, the applause from the audience was so loud that for a moment, the rain was not audible. I was truly moved by the dedication of the Technology enthusiasts. Pinal Dave After Presenting session at TechEd India 2010 The abstract of the session is as follows: The Microsoft SQL Server 2008 delivers new spatial data types that enable you to consume, use, and extend location-based data through spatial-enabled applications. Attend this session to learn how to use spatial functionality in next version of SQL Server to build and optimize spatial queries. This session outlines the new geography data type to store geodetic spatial data and perform operations on it, use the new geometry data type to store planar spatial data and perform operations on it, take advantage of new spatial indexes for high performance queries, use the new spatial results tab to quickly and easily view spatial query results directly from within Management Studio, extend spatial data capabilities by building or integrating location-enabled applications through support for spatial standards and specifications and much more. Time: 8:00 PM – onwards Dinner by Sponsors After the lively session during the day, there was another dinner party courtesy of one of the sponsors of TechEd. All the MVPs and several Community leaders were present at the dinner. I would like to express my gratitude to Abhishek Kant for organizing this wonderful event for us. It was a blast and really relaxing in all angles. We all stayed there for a long time and talked about our sweet and unforgettable memories of the event. Pinal Dave and Bijoy Singhal It was really one wonderful event. After writing this much, I say that I have no words to express about how much I enjoyed TechEd. However, it is true that I shared with you only 1% of the total activities I have done at the event. There were so many people I have met, yet were not mentioned here although I wanted to write their names here, too . Anyway, I have learned so many things and up until now, I am not able to get over all the fun I had in this event. Pinal Dave at TechEd India 2010 The Next Days – April 15, 2010 – till today I am still not able to get my mind out of the whole experience I had at TechEd India 2010. It was like a whole Microsoft Family working together to celebrate a happy occasion. TechEd India – Truly An Unforgettable Experience! Reference : Pinal Dave (http://blog.SQLAuthority.com) Filed under: About Me, MVP, Pinal Dave, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQLAuthority Author Visit, SQLAuthority News, SQLServer, T SQL, Technology Tagged: TechEd, TechEdIn

    Read the article

  • Node.js Adventure - Storage Services and Service Runtime

    - by Shaun
    When I described on how to host a Node.js application on Windows Azure, one of questions might be raised about how to consume the vary Windows Azure services, such as the storage, service bus, access control, etc.. Interact with windows azure services is available in Node.js through the Windows Azure Node.js SDK, which is a module available in NPM. In this post I would like to describe on how to use Windows Azure Storage (a.k.a. WAS) as well as the service runtime.   Consume Windows Azure Storage Let’s firstly have a look on how to consume WAS through Node.js. As we know in the previous post we can host Node.js application on Windows Azure Web Site (a.k.a. WAWS) as well as Windows Azure Cloud Service (a.k.a. WACS). In theory, WAWS is also built on top of WACS worker roles with some more features. Hence in this post I will only demonstrate for hosting in WACS worker role. The Node.js code can be used when consuming WAS when hosted on WAWS. But since there’s no roles in WAWS, the code for consuming service runtime mentioned in the next section cannot be used for WAWS node application. We can use the solution that I created in my last post. Alternatively we can create a new windows azure project in Visual Studio with a worker role, add the “node.exe” and “index.js” and install “express” and “node-sqlserver” modules, make all files as “Copy always”. In order to use windows azure services we need to have Windows Azure Node.js SDK, as knows as a module named “azure” which can be installed through NPM. Once we downloaded and installed, we need to include them in our worker role project and make them as “Copy always”. You can use my “Copy all always” tool mentioned in my last post to update the currently worker role project file. You can also find the source code of this tool here. The source code of Windows Azure SDK for Node.js can be found in its GitHub page. It contains two parts. One is a CLI tool which provides a cross platform command line package for Mac and Linux to manage WAWS and Windows Azure Virtual Machines (a.k.a. WAVM). The other is a library for managing and consuming vary windows azure services includes tables, blobs, queues, service bus and the service runtime. I will not cover all of them but will only demonstrate on how to use tables and service runtime information in this post. You can find the full document of this SDK here. Back to Visual Studio and open the “index.js”, let’s continue our application from the last post, which was working against Windows Azure SQL Database (a.k.a. WASD). The code should looks like this. 1: var express = require("express"); 2: var sql = require("node-sqlserver"); 3:  4: var connectionString = "Driver={SQL Server Native Client 10.0};Server=tcp:ac6271ya9e.database.windows.net,1433;Database=synctile;Uid=shaunxu@ac6271ya9e;Pwd={PASSWORD};Encrypt=yes;Connection Timeout=30;"; 5: var port = 80; 6:  7: var app = express(); 8:  9: app.configure(function () { 10: app.use(express.bodyParser()); 11: }); 12:  13: app.get("/", function (req, res) { 14: sql.open(connectionString, function (err, conn) { 15: if (err) { 16: console.log(err); 17: res.send(500, "Cannot open connection."); 18: } 19: else { 20: conn.queryRaw("SELECT * FROM [Resource]", function (err, results) { 21: if (err) { 22: console.log(err); 23: res.send(500, "Cannot retrieve records."); 24: } 25: else { 26: res.json(results); 27: } 28: }); 29: } 30: }); 31: }); 32:  33: app.get("/text/:key/:culture", function (req, res) { 34: sql.open(connectionString, function (err, conn) { 35: if (err) { 36: console.log(err); 37: res.send(500, "Cannot open connection."); 38: } 39: else { 40: var key = req.params.key; 41: var culture = req.params.culture; 42: var command = "SELECT * FROM [Resource] WHERE [Key] = '" + key + "' AND [Culture] = '" + culture + "'"; 43: conn.queryRaw(command, function (err, results) { 44: if (err) { 45: console.log(err); 46: res.send(500, "Cannot retrieve records."); 47: } 48: else { 49: res.json(results); 50: } 51: }); 52: } 53: }); 54: }); 55:  56: app.get("/sproc/:key/:culture", function (req, res) { 57: sql.open(connectionString, function (err, conn) { 58: if (err) { 59: console.log(err); 60: res.send(500, "Cannot open connection."); 61: } 62: else { 63: var key = req.params.key; 64: var culture = req.params.culture; 65: var command = "EXEC GetItem '" + key + "', '" + culture + "'"; 66: conn.queryRaw(command, function (err, results) { 67: if (err) { 68: console.log(err); 69: res.send(500, "Cannot retrieve records."); 70: } 71: else { 72: res.json(results); 73: } 74: }); 75: } 76: }); 77: }); 78:  79: app.post("/new", function (req, res) { 80: var key = req.body.key; 81: var culture = req.body.culture; 82: var val = req.body.val; 83:  84: sql.open(connectionString, function (err, conn) { 85: if (err) { 86: console.log(err); 87: res.send(500, "Cannot open connection."); 88: } 89: else { 90: var command = "INSERT INTO [Resource] VALUES ('" + key + "', '" + culture + "', N'" + val + "')"; 91: conn.queryRaw(command, function (err, results) { 92: if (err) { 93: console.log(err); 94: res.send(500, "Cannot retrieve records."); 95: } 96: else { 97: res.send(200, "Inserted Successful"); 98: } 99: }); 100: } 101: }); 102: }); 103:  104: app.listen(port); Now let’s create a new function, copy the records from WASD to table service. 1. Delete the table named “resource”. 2. Create a new table named “resource”. These 2 steps ensures that we have an empty table. 3. Load all records from the “resource” table in WASD. 4. For each records loaded from WASD, insert them into the table one by one. 5. Prompt to user when finished. In order to use table service we need the storage account and key, which can be found from the developer portal. Just select the storage account and click the Manage Keys button. Then create two local variants in our Node.js application for the storage account name and key. Since we need to use WAS we need to import the azure module. Also I created another variant stored the table name. In order to work with table service I need to create the storage client for table service. This is very similar as the Windows Azure SDK for .NET. As the code below I created a new variant named “client” and use “createTableService”, specified my storage account name and key. 1: var azure = require("azure"); 2: var storageAccountName = "synctile"; 3: var storageAccountKey = "/cOy9L7xysXOgPYU9FjDvjrRAhaMX/5tnOpcjqloPNDJYucbgTy7MOrAW7CbUg6PjaDdmyl+6pkwUnKETsPVNw=="; 4: var tableName = "resource"; 5: var client = azure.createTableService(storageAccountName, storageAccountKey); Now create a new function for URL “/was/init” so that we can trigger it through browser. Then in this function we will firstly load all records from WASD. 1: app.get("/was/init", function (req, res) { 2: // load all records from windows azure sql database 3: sql.open(connectionString, function (err, conn) { 4: if (err) { 5: console.log(err); 6: res.send(500, "Cannot open connection."); 7: } 8: else { 9: conn.queryRaw("SELECT * FROM [Resource]", function (err, results) { 10: if (err) { 11: console.log(err); 12: res.send(500, "Cannot retrieve records."); 13: } 14: else { 15: if (results.rows.length > 0) { 16: // begin to transform the records into table service 17: } 18: } 19: }); 20: } 21: }); 22: }); When we succeed loaded all records we can start to transform them into table service. First I need to recreate the table in table service. This can be done by deleting and creating the table through table client I had just created previously. 1: app.get("/was/init", function (req, res) { 2: // load all records from windows azure sql database 3: sql.open(connectionString, function (err, conn) { 4: if (err) { 5: console.log(err); 6: res.send(500, "Cannot open connection."); 7: } 8: else { 9: conn.queryRaw("SELECT * FROM [Resource]", function (err, results) { 10: if (err) { 11: console.log(err); 12: res.send(500, "Cannot retrieve records."); 13: } 14: else { 15: if (results.rows.length > 0) { 16: // begin to transform the records into table service 17: // recreate the table named 'resource' 18: client.deleteTable(tableName, function (error) { 19: client.createTableIfNotExists(tableName, function (error) { 20: if (error) { 21: error["target"] = "createTableIfNotExists"; 22: res.send(500, error); 23: } 24: else { 25: // transform the records 26: } 27: }); 28: }); 29: } 30: } 31: }); 32: } 33: }); 34: }); As you can see, the azure SDK provide its methods in callback pattern. In fact, almost all modules in Node.js use the callback pattern. For example, when I deleted a table I invoked “deleteTable” method, provided the name of the table and a callback function which will be performed when the table had been deleted or failed. Underlying, the azure module will perform the table deletion operation in POSIX async threads pool asynchronously. And once it’s done the callback function will be performed. This is the reason we need to nest the table creation code inside the deletion function. If we perform the table creation code after the deletion code then they will be invoked in parallel. Next, for each records in WASD I created an entity and then insert into the table service. Finally I send the response to the browser. Can you find a bug in the code below? I will describe it later in this post. 1: app.get("/was/init", function (req, res) { 2: // load all records from windows azure sql database 3: sql.open(connectionString, function (err, conn) { 4: if (err) { 5: console.log(err); 6: res.send(500, "Cannot open connection."); 7: } 8: else { 9: conn.queryRaw("SELECT * FROM [Resource]", function (err, results) { 10: if (err) { 11: console.log(err); 12: res.send(500, "Cannot retrieve records."); 13: } 14: else { 15: if (results.rows.length > 0) { 16: // begin to transform the records into table service 17: // recreate the table named 'resource' 18: client.deleteTable(tableName, function (error) { 19: client.createTableIfNotExists(tableName, function (error) { 20: if (error) { 21: error["target"] = "createTableIfNotExists"; 22: res.send(500, error); 23: } 24: else { 25: // transform the records 26: for (var i = 0; i < results.rows.length; i++) { 27: var entity = { 28: "PartitionKey": results.rows[i][1], 29: "RowKey": results.rows[i][0], 30: "Value": results.rows[i][2] 31: }; 32: client.insertEntity(tableName, entity, function (error) { 33: if (error) { 34: error["target"] = "insertEntity"; 35: res.send(500, error); 36: } 37: else { 38: console.log("entity inserted"); 39: } 40: }); 41: } 42: // send the 43: console.log("all done"); 44: res.send(200, "All done!"); 45: } 46: }); 47: }); 48: } 49: } 50: }); 51: } 52: }); 53: }); Now we can publish it to the cloud and have a try. But normally we’d better test it at the local emulator first. In Node.js SDK there are three build-in properties which provides the account name, key and host address for local storage emulator. We can use them to initialize our table service client. We also need to change the SQL connection string to let it use my local database. The code will be changed as below. 1: // windows azure sql database 2: //var connectionString = "Driver={SQL Server Native Client 10.0};Server=tcp:ac6271ya9e.database.windows.net,1433;Database=synctile;Uid=shaunxu@ac6271ya9e;Pwd=eszqu94XZY;Encrypt=yes;Connection Timeout=30;"; 3: // sql server 4: var connectionString = "Driver={SQL Server Native Client 11.0};Server={.};Database={Caspar};Trusted_Connection={Yes};"; 5:  6: var azure = require("azure"); 7: var storageAccountName = "synctile"; 8: var storageAccountKey = "/cOy9L7xysXOgPYU9FjDvjrRAhaMX/5tnOpcjqloPNDJYucbgTy7MOrAW7CbUg6PjaDdmyl+6pkwUnKETsPVNw=="; 9: var tableName = "resource"; 10: // windows azure storage 11: //var client = azure.createTableService(storageAccountName, storageAccountKey); 12: // local storage emulator 13: var client = azure.createTableService(azure.ServiceClient.DEVSTORE_STORAGE_ACCOUNT, azure.ServiceClient.DEVSTORE_STORAGE_ACCESS_KEY, azure.ServiceClient.DEVSTORE_TABLE_HOST); Now let’s run the application and navigate to “localhost:12345/was/init” as I hosted it on port 12345. We can find it transformed the data from my local database to local table service. Everything looks fine. But there is a bug in my code. If we have a look on the Node.js command window we will find that it sent response before all records had been inserted, which is not what I expected. The reason is that, as I mentioned before, Node.js perform all IO operations in non-blocking model. When we inserted the records we executed the table service insert method in parallel, and the operation of sending response was also executed in parallel, even though I wrote it at the end of my logic. The correct logic should be, when all entities had been copied to table service with no error, then I will send response to the browser, otherwise I should send error message to the browser. To do so I need to import another module named “async”, which helps us to coordinate our asynchronous code. Install the module and import it at the beginning of the code. Then we can use its “forEach” method for the asynchronous code of inserting table entities. The first argument of “forEach” is the array that will be performed. The second argument is the operation for each items in the array. And the third argument will be invoked then all items had been performed or any errors occurred. Here we can send our response to browser. 1: app.get("/was/init", function (req, res) { 2: // load all records from windows azure sql database 3: sql.open(connectionString, function (err, conn) { 4: if (err) { 5: console.log(err); 6: res.send(500, "Cannot open connection."); 7: } 8: else { 9: conn.queryRaw("SELECT * FROM [Resource]", function (err, results) { 10: if (err) { 11: console.log(err); 12: res.send(500, "Cannot retrieve records."); 13: } 14: else { 15: if (results.rows.length > 0) { 16: // begin to transform the records into table service 17: // recreate the table named 'resource' 18: client.deleteTable(tableName, function (error) { 19: client.createTableIfNotExists(tableName, function (error) { 20: if (error) { 21: error["target"] = "createTableIfNotExists"; 22: res.send(500, error); 23: } 24: else { 25: async.forEach(results.rows, 26: // transform the records 27: function (row, callback) { 28: var entity = { 29: "PartitionKey": row[1], 30: "RowKey": row[0], 31: "Value": row[2] 32: }; 33: client.insertEntity(tableName, entity, function (error) { 34: if (error) { 35: callback(error); 36: } 37: else { 38: console.log("entity inserted."); 39: callback(null); 40: } 41: }); 42: }, 43: // send reponse 44: function (error) { 45: if (error) { 46: error["target"] = "insertEntity"; 47: res.send(500, error); 48: } 49: else { 50: console.log("all done"); 51: res.send(200, "All done!"); 52: } 53: } 54: ); 55: } 56: }); 57: }); 58: } 59: } 60: }); 61: } 62: }); 63: }); Run it locally and now we can find the response was sent after all entities had been inserted. Query entities against table service is simple as well. Just use the “queryEntity” method from the table service client and providing the partition key and row key. We can also provide a complex query criteria as well, for example the code here. In the code below I queried an entity by the partition key and row key, and return the proper localization value in response. 1: app.get("/was/:key/:culture", function (req, res) { 2: var key = req.params.key; 3: var culture = req.params.culture; 4: client.queryEntity(tableName, culture, key, function (error, entity) { 5: if (error) { 6: res.send(500, error); 7: } 8: else { 9: res.json(entity); 10: } 11: }); 12: }); And then tested it on local emulator. Finally if we want to publish this application to the cloud we should change the database connection string and storage account. For more information about how to consume blob and queue service, as well as the service bus please refer to the MSDN page.   Consume Service Runtime As I mentioned above, before we published our application to the cloud we need to change the connection string and account information in our code. But if you had played with WACS you should have known that the service runtime provides the ability to retrieve configuration settings, endpoints and local resource information at runtime. Which means we can have these values defined in CSCFG and CSDEF files and then the runtime should be able to retrieve the proper values. For example we can add some role settings though the property window of the role, specify the connection string and storage account for cloud and local. And the can also use the endpoint which defined in role environment to our Node.js application. In Node.js SDK we can get an object from “azure.RoleEnvironment”, which provides the functionalities to retrieve the configuration settings and endpoints, etc.. In the code below I defined the connection string variants and then use the SDK to retrieve and initialize the table client. 1: var connectionString = ""; 2: var storageAccountName = ""; 3: var storageAccountKey = ""; 4: var tableName = ""; 5: var client; 6:  7: azure.RoleEnvironment.getConfigurationSettings(function (error, settings) { 8: if (error) { 9: console.log("ERROR: getConfigurationSettings"); 10: console.log(JSON.stringify(error)); 11: } 12: else { 13: console.log(JSON.stringify(settings)); 14: connectionString = settings["SqlConnectionString"]; 15: storageAccountName = settings["StorageAccountName"]; 16: storageAccountKey = settings["StorageAccountKey"]; 17: tableName = settings["TableName"]; 18:  19: console.log("connectionString = %s", connectionString); 20: console.log("storageAccountName = %s", storageAccountName); 21: console.log("storageAccountKey = %s", storageAccountKey); 22: console.log("tableName = %s", tableName); 23:  24: client = azure.createTableService(storageAccountName, storageAccountKey); 25: } 26: }); In this way we don’t need to amend the code for the configurations between local and cloud environment since the service runtime will take care of it. At the end of the code we will listen the application on the port retrieved from SDK as well. 1: azure.RoleEnvironment.getCurrentRoleInstance(function (error, instance) { 2: if (error) { 3: console.log("ERROR: getCurrentRoleInstance"); 4: console.log(JSON.stringify(error)); 5: } 6: else { 7: console.log(JSON.stringify(instance)); 8: if (instance["endpoints"] && instance["endpoints"]["nodejs"]) { 9: var endpoint = instance["endpoints"]["nodejs"]; 10: app.listen(endpoint["port"]); 11: } 12: else { 13: app.listen(8080); 14: } 15: } 16: }); But if we tested the application right now we will find that it cannot retrieve any values from service runtime. This is because by default, the entry point of this role was defined to the worker role class. In windows azure environment the service runtime will open a named pipeline to the entry point instance, so that it can connect to the runtime and retrieve values. But in this case, since the entry point was worker role and the Node.js was opened inside the role, the named pipeline was established between our worker role class and service runtime, so our Node.js application cannot use it. To fix this problem we need to open the CSDEF file under the azure project, add a new element named Runtime. Then add an element named EntryPoint which specify the Node.js command line. So that the Node.js application will have the connection to service runtime, then it’s able to read the configurations. Start the Node.js at local emulator we can find it retrieved the connections, storage account for local. And if we publish our application to azure then it works with WASD and storage service through the configurations for cloud.   Summary In this post I demonstrated how to use Windows Azure SDK for Node.js to interact with storage service, especially the table service. I also demonstrated on how to use WACS service runtime, how to retrieve the configuration settings and the endpoint information. And in order to make the service runtime available to my Node.js application I need to create an entry point element in CSDEF file and set “node.exe” as the entry point. I used five posts to introduce and demonstrate on how to run a Node.js application on Windows platform, how to use Windows Azure Web Site and Windows Azure Cloud Service worker role to host our Node.js application. I also described how to work with other services provided by Windows Azure platform through Windows Azure SDK for Node.js. Node.js is a very new and young network application platform. But since it’s very simple and easy to learn and deploy, as well as, it utilizes single thread non-blocking IO model, Node.js became more and more popular on web application and web service development especially for those IO sensitive projects. And as Node.js is very good at scaling-out, it’s more useful on cloud computing platform. Use Node.js on Windows platform is new, too. The modules for SQL database and Windows Azure SDK are still under development and enhancement. It doesn’t support SQL parameter in “node-sqlserver”. It does support using storage connection string to create the storage client in “azure”. But Microsoft is working on make them easier to use, working on add more features and functionalities.   PS, you can download the source code here. You can download the source code of my “Copy all always” tool here.   Hope this helps, Shaun All documents and related graphics, codes are provided "AS IS" without warranty of any kind. Copyright © Shaun Ziyan Xu. This work is licensed under the Creative Commons License.

    Read the article

  • Ubuntu: Failure to login with multiple video adapters

    - by tsilb
    Forgive my ignorance, for I am a complete linux noob. I have a computer with three video cards and six monitors. Works great on Windows. Trying to get it to run Ubuntu as well. It loads fine when I have it configured to run on one adapter; detects both screens, runs ok. But I want to turn the other 4 monitors on and run the whole thing as one extended desktop (one session, etc). So I downloaded and installed the newest ATI driver for Linux, which seems to work, kinda. I ran this to set up the screens: aticonfig --adapter=all --initial -f Now when I boot, Ubuntu seems to turn on all the screens (3 viewports, each with two cloned displays from what I can tell). When I enter my login info OR move the mouse off the main screen, the screens freeze and the kbd/ms become unresponsive. aticonfig generated xorg.conf included below. Have tried the following: aticonfig -initial -f - works, but only detects the primary adapter and 2 screens aticccle - Tells me I have to reboot after enabling the other cards. Then goes into above described freezing state. aticonfig --adapter=all --initial -f - see above Manually editing xorg.conf file with my limited knowledge - Was able to get two adapters running, but only the second adapter initialized while the primary stopped at the Ubuntu boot screen. Was unable to see the login prompt. Froze after I logged in blindly (was able to hear the login sound). Using generic "radeon" driver instead of ATI Proprietary driver with the above init attempts Toggling xinerama Various combinations of the above Hardware: Intel Core 2 Quad q6600 8GB DDR2 (3x) ATI Radeon HD 4680 5 monitors (21W, 21W, 22W Portrait, 22W Portrait, 19")and an HDTV (26"W, HDMI) in a horizontal arrangement I know next to nothing about Linux/Ubuntu aside from basic filesystem navigation, editing text files, and accessing my local and networked Windows stores and shares. Basically this is the most advanced thing I've had to do. I installed today. Please advise how to make this configuration work. my xorg.conf: Section "ServerLayout" Identifier "Layout0" Screen 0 "aticonfig-Screen[0]-0" 0 0 Screen "aticonfig-Screen[1]-0" RightOf "aticonfig-Screen[0]-0" Screen "aticonfig-Screen[2]-0" RightOf "aticonfig-Screen[1]-0" Option "RenderAccel" "true" Option "AllowGLXWithComposite" "true" EndSection Section "Files" EndSection Section "Module" EndSection Section "ServerFlags" Option "Xinerama" "0" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[1]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[2]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "aticonfig-Device[1]-0" Driver "fglrx" BusID "PCI:3:0:0" EndSection Section "Device" Identifier "aticonfig-Device[2]-0" Driver "fglrx" BusID "PCI:4:0:0" EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "aticonfig-Monitor[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[1]-0" Device "aticonfig-Device[1]-0" Monitor "aticonfig-Monitor[1]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[2]-0" Device "aticonfig-Device[2]-0" Monitor "aticonfig-Monitor[2]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

    Read the article

  • Why are USB 2.0 devices crashing my system?

    - by BenAlabaster
    Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic baby-ATX motherboard with no identifying markings. CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. There's one stamp on the motherboard that says "Rev.B". On board it has 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. It has an 80Gb Western Digital hard drive freshly formatted and built with Windows XP Professional with Service Pack 3 and all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 crashes the machine as soon as it starts up). It's got a Daytek MV150 15" touch screen running through the VGA and COM1 with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem If I hook any USB 2.0 devices to this machine, it hangs the whole machine and I have to hard boot it to get it back up. Workarounds found I can plug the same devices into the on board USB 1.0 connectors and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions I've tried disabling all the on board devices that I'm not using - such as the on board LAN, the second COM port, the AGP connector etc. through the BIOS in an (perhaps misguided or futile) attempt to reduce the power consumption... I don't think it had any effect but it didn't do any harm. I was wondering if the PSU wattage just isn't enough to drive the USB 2.0 devices; I've seen this suggested but haven't found any confirmation that this could really be an issue - nor have I found a way to work around this issue - if indeed it is one. Any ideas? The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference. I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself. Other thoughts Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine?

    Read the article

  • Informaton of pendriver with libudv on linux

    - by Catanzaro
    I'm doing a little app in C that read the driver information of my pendrive: Plugged it and typed dmesg: [ 7676.243994] scsi 7:0:0:0: Direct-Access Lexar USB Flash Drive 1100 PQ: 0 ANSI: 0 CCS [ 7676.248359] sd 7:0:0:0: Attached scsi generic sg2 type 0 [ 7676.256733] sd 7:0:0:0: [sdb] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB) [ 7676.266559] sd 7:0:0:0: [sdb] Write Protect is off [ 7676.266566] sd 7:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 7676.266569] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 7676.285373] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 7676.285383] sdb: sdb1 [ 7676.298661] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 7676.298667] sd 7:0:0:0: [sdb] Attached SCSI removable disk with "udevadm info -q all -n /dev/sdb" P: /devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb1/1-1/1-1:1.0/host7/target7:0:0/7:0:0:0/block/sdb N: sdb W: 36 S: block/8:16 S: disk/by-id/usb-Lexar_USB_Flash_Drive_AA5OCYQII8PSQXBB-0:0 S: disk/by-path/pci-0000:02:03.0-usb-0:1:1.0-scsi-0:0:0:0 E: UDEV_LOG=3 E: DEVPATH=/devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb1/1-1/1-1:1.0/host7/target7:0:0/7:0:0:0/block/sdb E: MAJOR=8 E: MINOR=16 E: DEVNAME=/dev/sdb E: DEVTYPE=disk E: SUBSYSTEM=block E: ID_VENDOR=Lexar E: ID_VENDOR_ENC=Lexar\x20\x20\x20 E: ID_VENDOR_ID=05dc E: ID_MODEL=USB_Flash_Drive E: ID_MODEL_ENC=USB\x20Flash\x20Drive\x20 E: ID_MODEL_ID=a813 E: ID_REVISION=1100 E: ID_SERIAL=Lexar_USB_Flash_Drive_AA5OCYQII8PSQXBB-0:0 E: ID_SERIAL_SHORT=AA5OCYQII8PSQXBB E: ID_TYPE=disk E: ID_INSTANCE=0:0 E: ID_BUS=usb E: ID_USB_INTERFACES=:080650: E: ID_USB_INTERFACE_NUM=00 E: ID_USB_DRIVER=usb-storage E: ID_PATH=pci-0000:02:03.0-usb-0:1:1.0-scsi-0:0:0:0 E: ID_PART_TABLE_TYPE=dos E: UDISKS_PRESENTATION_NOPOLICY=0 E: UDISKS_PARTITION_TABLE=1 E: UDISKS_PARTITION_TABLE_SCHEME=mbr E: UDISKS_PARTITION_TABLE_COUNT=1 E: DEVLINKS=/dev/block/8:16 /dev/disk/by-id/usb-Lexar_USB_Flash_Drive_AA5OCYQII8PSQXBB-0:0 /dev/disk/by-path/pci-0000:02:03.0-usb-0:1:1.0-scsi-0:0:0:0 and my software is: Codice: Seleziona tutto #include <stdio.h> #include <libudev.h> #include <stdlib.h> #include <locale.h> #include <unistd.h> int main(void) { struct udev_enumerate *enumerate; struct udev_list_entry *devices, *dev_list_entry; struct udev_device *dev; /* Create the udev object */ struct udev *udev = udev_new(); if (!udev) { printf("Can't create udev\n"); exit(0); } enumerate = udev_enumerate_new(udev); udev_enumerate_add_match_subsystem(enumerate, "scsi_generic"); udev_enumerate_scan_devices(enumerate); devices = udev_enumerate_get_list_entry(enumerate); udev_list_entry_foreach(dev_list_entry, devices) { const char *path; /* Get the filename of the /sys entry for the device and create a udev_device object (dev) representing it */ path = udev_list_entry_get_name(dev_list_entry); dev = udev_device_new_from_syspath(udev, path); /* usb_device_get_devnode() returns the path to the device node itself in /dev. */ printf("Device Node Path: %s\n", udev_device_get_devnode(dev)); /* The device pointed to by dev contains information about the hidraw device. In order to get information about the USB device, get the parent device with the subsystem/devtype pair of "usb"/"usb_device". This will be several levels up the tree, but the function will find it.*/ dev = udev_device_get_parent_with_subsystem_devtype( dev, "block", "disk"); if (!dev) { printf("Errore\n"); exit(1); } /* From here, we can call get_sysattr_value() for each file in the device's /sys entry. The strings passed into these functions (idProduct, idVendor, serial, etc.) correspond directly to the files in the directory which represents the USB device. Note that USB strings are Unicode, UCS2 encoded, but the strings returned from udev_device_get_sysattr_value() are UTF-8 encoded. */ printf(" VID/PID: %s %s\n", udev_device_get_sysattr_value(dev,"idVendor"), udev_device_get_sysattr_value(dev, "idProduct")); printf(" %s\n %s\n", udev_device_get_sysattr_value(dev,"manufacturer"), udev_device_get_sysattr_value(dev,"product")); printf(" serial: %s\n", udev_device_get_sysattr_value(dev, "serial")); udev_device_unref(dev); } /* Free the enumerator object */ udev_enumerate_unref(enumerate); udev_unref(udev); return 0; } the problem is that i obtain in output: Device Node Path: /dev/sg0 Errore and dont view information. subsystem and the devtype i think that are inserted well : "block" and "disk". thanks for help. Bye

    Read the article

  • External USB drive is failing

    - by dma_k
    I have an external USB 2.0 drive WD My Book Mirror Edition, running in RAID 1 (mirroring) mode. A while ago the hard drive started to fail: it stops responding (directories are not listed returning an error after a big timeout). Sometimes it works for weeks before a failure, sometimes – few hours. Small write operations (like removing few files or editing a small file) do not harm, but when copying large files to the drive over the network, or creating the archive locally, the kernel dumps. Also interesting to note that once kernel has failed, Linux does not want to reboot normally (reboot hangs); when Linux box is shutdown with power button, WD drive does not go to sleep mode (as it usually does): leds continue to run, pressing and holding the "shutdown" button on drive's back panel does not do anything; only unplugging the power cord helps. Here goes the boot log: Aug 16 00:32:21 kernel: [ 1.514106] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Aug 16 00:32:21 kernel: [ 1.657738] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 1.673747] ehci_hcd 0000:00:1d.7: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 1.673751] ehci_hcd 0000:00:1d.7: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.725224] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 Aug 16 00:32:21 kernel: [ 1.741647] ehci_hcd 0000:00:1d.7: using broken periodic workaround Aug 16 00:32:21 kernel: [ 1.761790] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported Aug 16 00:32:21 kernel: [ 1.761873] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdfff000 Aug 16 00:32:21 kernel: [ 1.796043] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 Aug 16 00:32:21 kernel: [ 1.879069] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 Aug 16 00:32:21 kernel: [ 1.895446] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 1.911796] usb usb1: Product: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.928015] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd Aug 16 00:32:21 kernel: [ 1.944331] usb usb1: SerialNumber: 0000:00:1d.7 Aug 16 00:32:21 kernel: [ 1.961285] usb usb1: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 1.994412] hub 1-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.010864] hub 1-0:1.0: 8 ports detected Aug 16 00:32:21 kernel: [ 2.085939] uhci_hcd: USB Universal Host Controller Interface driver Aug 16 00:32:21 kernel: [ 2.191945] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 2.226029] uhci_hcd 0000:00:1d.0: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.226034] uhci_hcd 0000:00:1d.0: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.243237] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 Aug 16 00:32:21 kernel: [ 2.260390] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fe00 Aug 16 00:32:21 kernel: [ 2.277517] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.294815] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.312173] usb usb2: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.329534] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.346828] usb usb2: SerialNumber: 0000:00:1d.0 Aug 16 00:32:21 kernel: [ 2.412989] usb usb2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.430651] usb 1-2: new high speed USB device using ehci_hcd and address 2 Aug 16 00:32:21 kernel: [ 2.449046] hub 2-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.466514] hub 2-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.484639] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Aug 16 00:32:21 kernel: [ 2.537750] uhci_hcd 0000:00:1d.1: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.537756] uhci_hcd 0000:00:1d.1: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.555085] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 Aug 16 00:32:21 kernel: [ 2.572231] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fd00 Aug 16 00:32:21 kernel: [ 2.589593] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.606869] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.624134] usb usb3: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.641329] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.658505] usb usb3: SerialNumber: 0000:00:1d.1 Aug 16 00:32:21 kernel: [ 2.675843] usb usb3: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.692864] hub 3-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.709651] hub 3-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.727378] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Aug 16 00:32:21 kernel: [ 2.768252] uhci_hcd 0000:00:1d.2: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.768258] uhci_hcd 0000:00:1d.2: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.806679] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 Aug 16 00:32:21 kernel: [ 2.824117] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fc00 Aug 16 00:32:21 kernel: [ 2.841405] usb 1-2: New USB device found, idVendor=1058, idProduct=1104 Aug 16 00:32:21 kernel: [ 2.858448] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Aug 16 00:32:21 kernel: [ 2.875347] usb 1-2: Product: My Book Aug 16 00:32:21 kernel: [ 2.892113] usb 1-2: Manufacturer: Western Digital Aug 16 00:32:21 kernel: [ 2.908915] usb 1-2: SerialNumber: 575532553130303530353538 Aug 16 00:32:21 kernel: [ 2.943242] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.960405] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.977615] usb usb4: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.994687] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.011711] usb usb4: SerialNumber: 0000:00:1d.2 Aug 16 00:32:21 kernel: [ 3.029589] usb usb4: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.082027] sd 2:0:0:0: [sda] Attached SCSI disk Aug 16 00:32:21 kernel: [ 3.103953] usb 1-2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.122625] hub 4-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.140484] hub 4-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.161680] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 Aug 16 00:32:21 kernel: [ 3.181257] uhci_hcd 0000:00:1d.3: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 3.181263] uhci_hcd 0000:00:1d.3: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.198614] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 Aug 16 00:32:21 kernel: [ 3.216012] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fb00 Aug 16 00:32:21 kernel: [ 3.249877] Uniform CD-ROM driver Revision: 3.20 Aug 16 00:32:21 kernel: [ 3.267765] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 3.284947] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 3.302023] usb usb5: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.319215] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.336298] usb usb5: SerialNumber: 0000:00:1d.3 Aug 16 00:32:21 kernel: [ 3.368377] Initializing USB Mass Storage driver... Aug 16 00:32:21 kernel: [ 3.390652] usbcore: registered new interface driver hiddev Aug 16 00:32:21 kernel: [ 3.408109] scsi4 : SCSI emulation for USB Mass Storage devices Aug 16 00:32:21 kernel: [ 3.425281] sr 0:0:1:0: Attached scsi CD-ROM sr0 Aug 16 00:32:21 kernel: [ 3.438978] sr 0:0:1:0: Attached scsi generic sg0 type 5 Aug 16 00:32:21 kernel: [ 3.456328] usbcore: registered new interface driver usb-storage Aug 16 00:32:21 kernel: [ 3.474564] usb-storage: device found at 2 Aug 16 00:32:21 kernel: [ 3.474567] usb-storage: waiting for device to settle before scanning Aug 16 00:32:21 kernel: [ 3.475320] sd 2:0:0:0: Attached scsi generic sg1 type 0 Aug 16 00:32:21 kernel: [ 3.492587] USB Mass Storage support registered. Aug 16 00:32:21 kernel: [ 3.510930] usb usb5: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.531076] hub 5-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.548399] hub 5-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.591743] input: Western Digital My Book as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2:1.1/input/input2 Aug 16 00:32:21 kernel: [ 3.609515] generic-usb 0003:1058:1104.0001: input,hidraw0: USB HID v1.11 Device [Western Digital My Book] on usb-0000:00:1d.7-2/input1 Aug 16 00:32:21 kernel: [ 3.627466] usbcore: registered new interface driver usbhid Aug 16 00:32:21 kernel: [ 8.581664] usb-storage: device scan complete Aug 16 00:32:21 kernel: [ 8.624270] scsi 4:0:0:0: Direct-Access WD My Book 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.655135] scsi 4:0:0:1: Enclosure WD My Book Device 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.675393] sd 4:0:0:0: Attached scsi generic sg2 type 0 Aug 16 00:32:21 kernel: [ 8.698669] scsi 4:0:0:1: Attached scsi generic sg3 type 13 Aug 16 00:32:21 kernel: [ 8.723370] sd 4:0:0:0: [sdb] 1953513472 512-byte logical blocks: (1.00 TB/931 GiB) Aug 16 00:32:21 kernel: [ 8.750477] sd 4:0:0:0: [sdb] Write Protect is off Aug 16 00:32:21 kernel: [ 8.769411] sd 4:0:0:0: [sdb] Mode Sense: 10 00 00 00 Aug 16 00:32:21 kernel: [ 8.769414] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.822971] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.841978] sdb: sdb1 Aug 16 00:32:21 kernel: [ 8.905580] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.924173] sd 4:0:0:0: [sdb] Attached SCSI disk Aug 16 00:32:21 kernel: [ 11.600492] XFS mounting filesystem sdb1 Aug 16 00:32:21 kernel: [ 12.222948] Ending clean XFS mount for filesystem: sdb1 After a while the following appears in a log: Aug 16 09:30:56 kernel: [32359.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:31:59 kernel: [32422.112035] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:33:00 kernel: [32483.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 And then it is followed by few kernel dumps, which I think, are not good: Aug 16 09:33:40 kernel: [32520.428027] INFO: task xfssyncd:1002 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32520.462689] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32520.497422] xfssyncd D c3d84a60 0 1002 2 0x00000000 Aug 16 09:33:40 kernel: [32520.532117] f6c9aa80 00000046 c1132742 c3d84a60 00000286 c1418100 c1418100 00000000 Aug 16 09:33:40 kernel: [32520.566867] f6c9ac3c c2808100 00000000 f653b18b 00001d76 00000001 f6c9aa80 c3c3f0e0 Aug 16 09:33:40 kernel: [32520.601343] 08e59242 f6c9ac3c 2e41392b 00000000 08e59242 00000000 c3f7fb48 0067385a Aug 16 09:33:40 kernel: [32520.635533] Call Trace: Aug 16 09:33:40 kernel: [32520.668991] [<c1132742>] ? cfq_set_request+0x0/0x290 Aug 16 09:33:40 kernel: [32520.702804] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32520.736555] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32520.770360] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32520.804110] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32520.837713] [<c1128230>] ? blk_peek_request+0x135/0x143 Aug 16 09:33:40 kernel: [32520.871265] [<f8582987>] ? scsi_dispatch_cmd+0x185/0x1e5 [scsi_mod] Aug 16 09:33:40 kernel: [32520.904407] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32520.937007] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32520.969033] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.000485] [<c10cffd1>] ? bio_add_page+0x28/0x2e Aug 16 09:33:40 kernel: [32521.031403] [<f8918d38>] ? _xfs_buf_ioapply+0x206/0x22b [xfs] Aug 16 09:33:40 kernel: [32521.061888] [<f89197bd>] ? xfs_buf_iorequest+0x38/0x60 [xfs] Aug 16 09:33:40 kernel: [32521.091845] [<f8907230>] ? xlog_bdstrat_cb+0x16/0x3d [xfs] Aug 16 09:33:40 kernel: [32521.121222] [<f8905781>] ? XFS_bwrite+0x32/0x64 [xfs] Aug 16 09:33:40 kernel: [32521.150007] [<f89059be>] ? xlog_sync+0x20b/0x311 [xfs] Aug 16 09:33:40 kernel: [32521.178214] [<f89112fc>] ? xfs_trans_ail_tail+0x12/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.205914] [<f8906261>] ? xlog_state_sync_all+0xa2/0x141 [xfs] Aug 16 09:33:40 kernel: [32521.233074] [<f8906611>] ? _xfs_log_force+0x51/0x68 [xfs] Aug 16 09:33:40 kernel: [32521.259664] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32521.285662] [<f8906636>] ? xfs_log_force+0xe/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.311171] [<f89202df>] ? xfs_sync_worker+0x17/0x5c [xfs] Aug 16 09:33:40 kernel: [32521.336117] [<f891fbb7>] ? xfssyncd+0x134/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.360498] [<f891fa83>] ? xfssyncd+0x0/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.384211] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32521.407890] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32521.430876] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32521.453394] INFO: task flush-8:16:12945 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32521.476116] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32521.498579] flush-8:16 D 00000000 0 12945 2 0x00000000 Aug 16 09:33:40 kernel: [32521.520649] f4e4d540 00000046 e412e940 00000000 00000002 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32521.542426] f4e4d6fc c2808100 00000000 00000000 000008b4 00000001 f4e4d540 c3c3f0e0 Aug 16 09:33:40 kernel: [32521.563745] 02e905a8 f4e4d6fc 007a5399 00000000 02e905a8 00000000 f4e2db48 00670b98 Aug 16 09:33:40 kernel: [32521.585077] Call Trace: Aug 16 09:33:40 kernel: [32521.605790] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32521.626184] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32521.646133] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32521.665659] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32521.684716] [<f891796e>] ? xfs_convert_page+0x30a/0x331 [xfs] Aug 16 09:33:40 kernel: [32521.703366] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32521.721644] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32521.739465] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.756896] [<c10cfa45>] ? bio_alloc_bioset+0x7b/0xba Aug 16 09:33:40 kernel: [32521.774046] [<f8917af0>] ? xfs_submit_ioend_bio+0x3b/0x44 [xfs] Aug 16 09:33:40 kernel: [32521.790694] [<f8917ba3>] ? xfs_submit_ioend+0xaa/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.806736] [<f891817d>] ? xfs_page_state_convert+0x5c0/0x61c [xfs] Aug 16 09:33:40 kernel: [32521.822859] [<c113705b>] ? __lookup_tag+0x8e/0xee Aug 16 09:33:40 kernel: [32521.838958] [<f891840d>] ? xfs_vm_writepage+0x91/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.855039] [<c108bbcc>] ? __writepage+0x8/0x22 Aug 16 09:33:40 kernel: [32521.871067] [<c108c17b>] ? write_cache_pages+0x1af/0x29f Aug 16 09:33:40 kernel: [32521.886616] [<c108bbc4>] ? __writepage+0x0/0x22 Aug 16 09:33:40 kernel: [32521.901593] [<c108c285>] ? generic_writepages+0x1a/0x21 Aug 16 09:33:40 kernel: [32521.916455] [<f8918338>] ? xfs_vm_writepages+0x0/0x38 [xfs] Aug 16 09:33:40 kernel: [32521.931484] [<c108c2a5>] ? do_writepages+0x19/0x25 Aug 16 09:33:40 kernel: [32521.946648] [<c10c80d9>] ? writeback_single_inode+0xc7/0x273 Aug 16 09:33:40 kernel: [32521.961675] [<c10c8c44>] ? writeback_inodes_wb+0x3dd/0x49c Aug 16 09:33:40 kernel: [32521.976831] [<c10c8e18>] ? wb_writeback+0x115/0x178 Aug 16 09:33:40 kernel: [32521.991778] [<c10c901f>] ? wb_do_writeback+0x121/0x131 Aug 16 09:33:40 kernel: [32522.006538] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32522.021091] [<c10c9050>] ? bdi_writeback_task+0x21/0x89 Aug 16 09:33:40 kernel: [32522.035493] [<c10979e5>] ? bdi_start_fn+0x59/0xa4 Aug 16 09:33:40 kernel: [32522.049765] [<c109798c>] ? bdi_start_fn+0x0/0xa4 Aug 16 09:33:40 kernel: [32522.063792] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32522.077612] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32522.091260] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32522.104966] INFO: task smartctl:13098 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32522.118883] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32522.133012] smartctl D 00000020 0 13098 13097 0x00000000 Aug 16 09:33:40 kernel: [32522.147221] e50b9540 00000086 c11d28a8 00000020 00000770 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32522.161720] e50b96fc c2808100 00000000 e53e8800 00000000 00000020 c3cec000 c13886c0 Aug 16 09:33:40 kernel: [32522.176217] f99dab68 e50b96fc 007a4f1e 00000001 c4082f24 c4082ed8 00000001 c3c3f0e0 Aug 16 09:33:40 kernel: [32522.190737] Call Trace: Aug 16 09:33:40 kernel: [32522.205038] [<c11d28a8>] ? __netdev_alloc_skb+0x14/0x2d Aug 16 09:33:40 kernel: [32522.219605] [<c126b799>] ? schedule_timeout+0x20/0xb0 Aug 16 09:33:40 kernel: [32522.234144] [<c112820d>] ? blk_peek_request+0x112/0x143 Aug 16 09:33:40 kernel: [32522.248649] [<f85873b6>] ? scsi_request_fn+0x3c1/0x47a [scsi_mod] Aug 16 09:33:40 kernel: [32522.263233] [<c103aba8>] ? del_timer+0x55/0x5c Aug 16 09:33:40 kernel: [32522.277773] [<c126b6a2>] ? wait_for_common+0xa4/0x100 Aug 16 09:33:40 kernel: [32522.292342] [<c102cd8d>] ? default_wake_function+0x0/0x8 Aug 16 09:33:40 kernel: [32522.306958] [<c112b3d1>] ? blk_execute_rq+0x8b/0xb2 Aug 16 09:33:40 kernel: [32522.321569] [<c112b2ac>] ? blk_end_sync_rq+0x0/0x23 Aug 16 09:33:40 kernel: [32522.336070] [<c112b58b>] ? blk_recount_segments+0x13/0x20 Aug 16 09:33:40 kernel: [32522.350583] [<c1127307>] ? blk_rq_bio_prep+0x44/0x74 Aug 16 09:33:40 kernel: [32522.365059] [<c112b0b2>] ? blk_rq_map_kern+0xc5/0xee Aug 16 09:33:40 kernel: [32522.379439] [<c112e2a5>] ? sg_scsi_ioctl+0x221/0x2aa Aug 16 09:33:40 kernel: [32522.393801] [<c112e672>] ? scsi_cmd_ioctl+0x344/0x39a Aug 16 09:33:40 kernel: [32522.408140] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.422566] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.436832] [<f87676aa>] ? sd_ioctl+0x90/0xb5 [sd_mod] Aug 16 09:33:40 kernel: [32522.451228] [<c112c35f>] ? __blkdev_driver_ioctl+0x53/0x63 Aug 16 09:33:40 kernel: [32522.465689] [<c112cbbf>] ? blkdev_ioctl+0x850/0x891 Aug 16 09:33:40 kernel: [32522.479982] [<c1020474>] ? __wake_up_common+0x34/0x59 Aug 16 09:33:40 kernel: [32522.494138] [<c10244cd>] ? complete+0x28/0x36 Aug 16 09:33:40 kernel: [32522.507986] [<c1086c64>] ? find_get_page+0x1f/0x81 Aug 16 09:33:40 kernel: [32522.521671] [<c10abed5>] ? add_partial+0xe/0x40 Aug 16 09:33:40 kernel: [32522.535285] [<c1086e68>] ? lock_page+0x8/0x1d Aug 16 09:33:40 kernel: [32522.548797] [<c1087432>] ? filemap_fault+0xb5/0x2e6 Aug 16 09:33:40 kernel: [32522.562141] [<c109941c>] ? __do_fault+0x381/0x3b1 Aug 16 09:33:40 kernel: [32522.575441] [<c10d0c30>] ? block_ioctl+0x27/0x2c Aug 16 09:33:40 kernel: [32522.588708] [<c10d0c09>] ? block_ioctl+0x0/0x2c Aug 16 09:33:40 kernel: [32522.601858] [<c10bcd78>] ? vfs_ioctl+0x1c/0x5f Aug 16 09:33:40 kernel: [32522.614917] [<c10bd30c>] ? do_vfs_ioctl+0x4aa/0x4e5 Aug 16 09:33:40 kernel: [32522.627961] [<c10350db>] ? __do_softirq+0x115/0x151 Aug 16 09:33:40 kernel: [32522.640901] [<c126e270>] ? do_page_fault+0x2f1/0x307 Aug 16 09:33:40 kernel: [32522.653803] [<c10bd388>] ? sys_ioctl+0x41/0x58 Aug 16 09:33:40 kernel: [32522.666674] [<c10030fb>] ? sysenter_do_call+0x12/0x28 Then again few messages reset high speed USB device using ehci_hcd and address 2. I have browsed and read similar error reports here and there and I tried: I have upgraded the kernel from v2.6.26-2 to 2.6.32-5, which has not solved the problem. They say, this might a cable problem. I have tried to replace the USB-to-miniUSB cable (that connects external drive with computer) with another one. No changes. Somebody suggests to try another USB port. I have only 4 external USB ports, tried another one with no success. They say to try uhci_hcd. I have unmounted the device, unloaded ehci_hcd and mounted again. The difference was that now in log I get reset full speed USB device using uhci_hcd and address 2 and similar kernel dumps after a while. They say to echo 128 > /sys/block/sdb/device/max_sectors. I tried it with ehci_hcd with no success (note: I have issued this command after the drive was mounted but before using it actively). I have lauched smartmond and checking periodically the output of smartctl: drive temperature is OK, number of bad sectors and uncorrectable errors is 0. Nothing suspicious is reported by S.M.A.R.T. except maybe the following: Aug 16 12:40:12 kernel: [43715.314566] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Aug 16 12:40:13 kernel: [43715.705622] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Of course, I have not tried all combinations of above. But unfortunately, I am run out of cardinal ideas. If anybody can advice something specific about the problem, you are very welcome.

    Read the article

  • Using Web Services from an XNA 4.0 WP7 Game

    - by Michael Cummings
    Now that the Windows Phone 7 development tools have been out for a while, let’s talk about how you can use them. Windows Phone 7 ( WP7 ) has two application types that you can create, either Silverlight or XNA, and you can’t really mix the two together. The development environment for WP7 is a special edition of Visual Studio 2010 called Visual Studio 2010 Express for Windows Phone. This edition will be installed with the WP7 tools, even if you have a full edition of VS2010 already installed. While you can use your full edition of VS2010 to do WP7 development, this astute developer has noticed that there are a few things that you can only do in the Express for Windows Phone edition. So lets start by discussing WP7 networking. On the WP7 platform the only networking available is through Web Services using WCF or if you’re really masochistic, you’ll use the WebClient to do http. In Silverlight, it’s fairly easy to wire up a WCF proxy to call a web service and get some data. In the XNA projects, not so much. Create WCF Service First, we’ll create our service that will return some information that we need in our game. Open Visual Studio 2010, and create a new WCF Web Service project. We’ll use the default implementation as we only need to see how to use a service, we are not interested in creating a really cool service at this point. However you may want to follow the instructions in the comments of Service1.svc.cs to change the name to something better, I used DataService and IDataService for the interface. You should now be able to run the project and the WCF Test Client will load and properly enumerate your service. At this point we have a functional service that can be consumed by our XNA game. Consume the WCF Service Open Visual Studio 2010 Express for Windows Phone and create a new XNA Game Studio 4.0 Windows Phone Game project. Now if you try to add a service reference to the project, you’ll notice that the option is not available. However, if you add a Silverlight application to your solution, you’ll notice that you can create a service reference there. So using the Silverlight project, we can create the service reference. Unfortunately you can’t reference the Silverlight project from the XNA Game project, so using Windows Explorer copy the Service References folder from the Silverlight project directory to the XNA Game project directory, then add the folder to your XNA Game project. You’ll need to set the property Build Action to None for all the files, except for Reference.cs, which should be Build. Truely, we only need Reference.cs but I find it easier to copy the whole folder. If you try to compile at this point, you’ll notice that we are missing  a couple of references, System.Runtime.Serialization, System.Net and System.ServiceModel. Add these to the XNA Game project and you should build successfully. You’ll also need to copy the ServiceReference.ClientConfig file and add it to your project. The WCF infrastructure looks for this file and will complain if it can’t find it. You’ll need to set the Copy to Output Directory property to Copy if Newer. We now need to add the code to call the service and display the results on the screen. Go ahead and add a SpriteFont resource to the Content project and load it in the Game project. There’s nothing here that’s changed much from 3.1 other than your Content project is now under the Solution node and not the Project node. While you’re at it, add a string field to store the result of the service call, and intialize it to string.Empty. Then in the Draw method, write the string out to the screen, only if it does not equal string.Empty. Now to wrap this up, lets create a new field that’s of the type DataServiceClient. In the Initialize Method, create a new instance of this type using its default contructor, then in the LoadContent we can call the service. Since we can only call the GetData method of our service asynchronously we need to set up a Completed event handler first. Thankfully, Visual Studio helps out a lot there just create, using the tab key whatever VS says to. In the GetDataAsyncCompleted event handler assign the service result ( e.Result) to your string field. If you run your game, you should get something like this : Enjoy!

    Read the article

  • Storage Configuration

    - by jchang
    Storage performance is not inherently complicated subject. The concepts are relatively simple. In fact, scaling storage performance is far easier compared with the difficulties encounters in scaling processor performance in NUMA systems. Storage performance is achieved by properly distributing IO over: 1) multiple independent PCI-E ports (system memory and IO bandwith is key) 2) multiple RAID controllers or host bus adapters (HBAs) 3) multiple storage IO channels (SAS or FC, complete path) most importantly,...(read more)

    Read the article

  • Upgrading Apache to 2.2.23 on ubuntu 12.04 LTS

    - by Salil P
    We had done a PCI scan on one of our servers running Ubuntu 12.04 LTS with apache 2.2.22. The scan reported a vulnerability in apache 2.2.22 (Apache HTTP Server Zero-Length Directory Name in LD_LIBRARY_PATH Vulnerability).The report states to upgrade the version to the latest stable release of either 2.2.23 or 2.2.24. How do I upgrade to the 2.2.23 to fix the vulnerability or is there a patch available that can fix this and if yes can you let me know how that can be patched.

    Read the article

  • Storage Configuration

    - by jchang
    Storage performance is not inherently complicated subject. The concepts are relatively simple. In fact, scaling storage performance is far easier compared with the difficulties encounters in scaling processor performance in NUMA systems. Storage performance is achieved by properly distributing IO over: 1) multiple independent PCI-E ports (system memory and IO bandwith is key) 2) multiple RAID controllers or host bus adapters (HBAs) 3) multiple storage IO channels (SAS or FC, complete path) most importantly,...(read more)

    Read the article

  • Ralink rt3090 driver installed and wireless doesn't work on Ubuntu 10.04

    - by Marcus Rene
    I have a LG A-410 lap-top (64 bits) with rt 3090 wireless card. Searching the problem I discover that I already have a rt 3090-dkms installed, but my wireless doesn't work. *-network UNCLAIMED description: Network controller product: RT3090 Wireless 802.11n 1T/1R PCIe vendor: RaLink physical id: 0 bus info: pci@0000:02:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:e5400000-e540ffff

    Read the article

  • External usb 3.0 hard drive is not recognised when plugged into usb 3 port (ubuntu natty 64 bit).

    - by kimangroo
    I have an Iomega Prestige Portable External Hard Drive 1TB USB 3.0. It works fine on windows 7 as a usb 3.0 drive. It isn't detected on ubuntu natty 64bit, 2.6.38-8-generic. fdisk -l cannot see it at all: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1bed746b Device Boot Start End Blocks Id System /dev/sda1 1 1689 13560832 27 Unknown /dev/sda2 * 1689 1702 102400 7 HPFS/NTFS /dev/sda3 1702 19978 146805760 7 HPFS/NTFS /dev/sda4 19978 60802 327914497 5 Extended /dev/sda5 25555 60802 283120640 7 HPFS/NTFS /dev/sda6 19978 23909 31571968 83 Linux /dev/sda7 23909 25555 13218816 82 Linux swap / Solaris Partition table entries are not in disk order lsusb can see it: Bus 003 Device 003: ID 059b:0070 Iomega Corp. Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 002 Device 004: ID 05fe:0011 Chic Technology Corp. Browser Mouse Bus 002 Device 003: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 005: ID 0489:e00f Foxconn / Hon Hai Bus 001 Device 004: ID 0c45:64b5 Microdia Bus 001 Device 003: ID 08ff:168f AuthenTec, Inc. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub And dmesg | grep -i xhci (I may have unplugged the drive and plugged it back in again after booting): [ 1.659060] pci 0000:04:00.0: xHCI HW did not halt within 2000 usec status = 0x0 [ 11.484971] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 11.484997] xhci_hcd 0000:04:00.0: setting latency timer to 64 [ 11.485002] xhci_hcd 0000:04:00.0: xHCI Host Controller [ 11.485064] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 [ 11.636149] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 [ 11.636241] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X [ 11.636246] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X [ 11.636251] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X [ 11.636256] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X [ 11.636261] xhci_hcd 0000:04:00.0: irq 47 for MSI/MSI-X [ 11.639654] xHCI xhci_add_endpoint called for root hub [ 11.639655] xHCI xhci_check_bandwidth called for root hub [ 11.956366] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 2 [ 12.001073] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.007059] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.012932] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.018922] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.049139] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.056754] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.131607] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 12.179717] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.686876] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 12.687058] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 12.687152] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 43.330737] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 2 [ 43.422579] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 43.422658] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af00 [ 43.422665] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af40 [ 43.422671] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af80 [ 43.422677] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669afc0 [ 43.531159] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 125.160248] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.766466] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 3 [ 903.807789] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.813530] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.819400] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.825104] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.855067] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862314] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862597] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.913211] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 904.424416] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 904.424599] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 904.424700] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 935.139021] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 3 [ 935.226075] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 935.226140] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b00 [ 935.226148] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b40 [ 935.226153] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b80 [ 935.226159] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186bc0 [ 935.343339] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst I thought it might be that the firmware wasn't compatible with linux or something, but when booting a live image of partedmagic, (2.6.38.4-pmagic), the drive was detected fine, I could mount it and got usb 3.0 speeds (at least they double the speeds I got from plugging same drive in usb 2 ports). dmesg in partedmagic did say something about no SuperSpeed endpoint which was an error I saw in a previous dmesg of ubuntu: Jun 27 15:49:02 (none) user.info kernel: [ 2.978743] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Jun 27 15:49:02 (none) user.debug kernel: [ 2.978771] xhci_hcd 0000:04:00.0: setting latency timer to 64 Jun 27 15:49:02 (none) user.info kernel: [ 2.978781] xhci_hcd 0000:04:00.0: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 2.978856] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 Jun 27 15:49:02 (none) user.info kernel: [ 3.089458] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 Jun 27 15:49:02 (none) user.debug kernel: [ 3.089541] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089544] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089546] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089548] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089550] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X Jun 27 15:49:02 (none) user.warn kernel: [ 3.092857] usb usb3: No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0 ep 129: using minimum values Jun 27 15:49:02 (none) user.info kernel: [ 3.092864] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 Jun 27 15:49:02 (none) user.info kernel: [ 3.092866] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Jun 27 15:49:02 (none) user.info kernel: [ 3.092867] usb usb3: Product: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 3.092869] usb usb3: Manufacturer: Linux 2.6.38.4-pmagic xhci_hcd Jun 27 15:49:02 (none) user.info kernel: [ 3.092870] usb usb3: SerialNumber: 0000:04:00.0 Jun 27 15:49:02 (none) user.debug kernel: [ 3.092961] xHCI xhci_add_endpoint called for root hub Jun 27 15:49:02 (none) user.debug kernel: [ 3.092963] xHCI xhci_check_bandwidth called for root hub Well I have no idea what's going wrong, and I haven't had much luck from google and the forums so far. A number of unanswered threads with people with similar error messages and problems only. Hopefully someone here can help or point me in the right direction?!

    Read the article

  • No GLX on Intel card with multiseat with additional nVidia card

    - by MeanEYE
    I have multiseat configured and my Xorg has 2 server layouts. One is for nVidia card and other is for Intel card. They both work, but display server assigned to Intel card doesn't have hardware acceleration since DRI and GLX module being used is from nVidia driver. So my question is, can I configure layouts somehow to use right DRI and GLX with each card? My Xorg.conf: Section "ServerLayout" Identifier "Default" Screen 0 "Screen0" 0 0 Option "Xinerama" "0" EndSection Section "ServerLayout" Identifier "TV" Screen 0 "Screen1" 0 0 Option "Xinerama" "0" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "DELL E198WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Unknown" Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GT 610" EndSection Section "Device" Identifier "Device1" Driver "intel" BusID "PCI:0:2:0" Option "AccelMethod" "uxa" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "Stereo" "0" Option "nvidiaXineramaInfoOrder" "DFP-1" Option "metamodes" "DFP-0: nvidia-auto-select +1440+0, DFP-1: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection Log file for Intel: [ 18.239] X.Org X Server 1.13.0 Release Date: 2012-09-05 [ 18.239] X Protocol Version 11, Revision 0 [ 18.239] Build Operating System: Linux 2.6.24-32-xen x86_64 Ubuntu [ 18.239] Current Operating System: Linux bytewiper 3.5.0-18-generic #29-Ubuntu SMP Fri Oct 19 10:26:51 UTC 2012 x86_64 [ 18.239] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.5.0-18-generic root=UUID=fc0616fd-f212-4846-9241-ba4a492f0513 ro quiet splash [ 18.239] Build Date: 20 September 2012 11:55:20AM [ 18.239] xorg-server 2:1.13.0+git20120920.70e57668-0ubuntu0ricotz (For technical support please see http://www.ubuntu.com/support) [ 18.239] Current version of pixman: 0.26.0 [ 18.239] Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. [ 18.239] Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. [ 18.239] (==) Log file: "/var/log/Xorg.1.log", Time: Wed Nov 21 18:32:14 2012 [ 18.239] (==) Using config file: "/etc/X11/xorg.conf" [ 18.239] (==) Using system config directory "/usr/share/X11/xorg.conf.d" [ 18.239] (++) ServerLayout "TV" [ 18.239] (**) |-->Screen "Screen1" (0) [ 18.239] (**) | |-->Monitor "Monitor1" [ 18.240] (**) | |-->Device "Device1" [ 18.240] (**) Option "Xinerama" "0" [ 18.240] (==) Automatically adding devices [ 18.240] (==) Automatically enabling devices [ 18.240] (==) Automatically adding GPU devices [ 18.240] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (==) FontPath set to: /usr/share/fonts/X11/misc, /usr/share/fonts/X11/Type1, built-ins [ 18.240] (==) ModulePath set to "/usr/lib/x86_64-linux-gnu/xorg/extra-modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules" [ 18.240] (II) The server relies on udev to provide the list of input devices. If no devices become available, reconfigure udev or disable AutoAddDevices. [ 18.240] (II) Loader magic: 0x7f6917944c40 [ 18.240] (II) Module ABI versions: [ 18.240] X.Org ANSI C Emulation: 0.4 [ 18.240] X.Org Video Driver: 13.0 [ 18.240] X.Org XInput driver : 18.0 [ 18.240] X.Org Server Extension : 7.0 [ 18.240] (II) config/udev: Adding drm device (/dev/dri/card0) [ 18.241] (--) PCI: (0:0:2:0) 8086:0152:1043:84ca rev 9, Mem @ 0xf7400000/4194304, 0xd0000000/268435456, I/O @ 0x0000f000/64 [ 18.241] (--) PCI:*(0:1:0:0) 10de:104a:1458:3546 rev 161, Mem @ 0xf6000000/16777216, 0xe0000000/134217728, 0xe8000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288 [ 18.241] (II) Open ACPI successful (/var/run/acpid.socket) [ 18.241] Initializing built-in extension Generic Event Extension [ 18.241] Initializing built-in extension SHAPE [ 18.241] Initializing built-in extension MIT-SHM [ 18.241] Initializing built-in extension XInputExtension [ 18.241] Initializing built-in extension XTEST [ 18.241] Initializing built-in extension BIG-REQUESTS [ 18.241] Initializing built-in extension SYNC [ 18.241] Initializing built-in extension XKEYBOARD [ 18.241] Initializing built-in extension XC-MISC [ 18.241] Initializing built-in extension SECURITY [ 18.241] Initializing built-in extension XINERAMA [ 18.241] Initializing built-in extension XFIXES [ 18.241] Initializing built-in extension RENDER [ 18.241] Initializing built-in extension RANDR [ 18.241] Initializing built-in extension COMPOSITE [ 18.241] Initializing built-in extension DAMAGE [ 18.241] Initializing built-in extension MIT-SCREEN-SAVER [ 18.241] Initializing built-in extension DOUBLE-BUFFER [ 18.241] Initializing built-in extension RECORD [ 18.241] Initializing built-in extension DPMS [ 18.241] Initializing built-in extension X-Resource [ 18.241] Initializing built-in extension XVideo [ 18.241] Initializing built-in extension XVideo-MotionCompensation [ 18.241] Initializing built-in extension XFree86-VidModeExtension [ 18.241] Initializing built-in extension XFree86-DGA [ 18.241] Initializing built-in extension XFree86-DRI [ 18.241] Initializing built-in extension DRI2 [ 18.241] (II) LoadModule: "glx" [ 18.241] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/libglx.so [ 18.247] (II) Module glx: vendor="NVIDIA Corporation" [ 18.247] compiled for 4.0.2, module version = 1.0.0 [ 18.247] Module class: X.Org Server Extension [ 18.247] (II) NVIDIA GLX Module 310.19 Thu Nov 8 01:12:43 PST 2012 [ 18.247] Loading extension GLX [ 18.247] (II) LoadModule: "intel" [ 18.248] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so [ 18.248] (II) Module intel: vendor="X.Org Foundation" [ 18.248] compiled for 1.13.0, module version = 2.20.13 [ 18.248] Module class: X.Org Video Driver [ 18.248] ABI class: X.Org Video Driver, version 13.0 [ 18.248] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45, 4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale, Sandybridge Desktop (GT1), Sandybridge Desktop (GT2), Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1), Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+), Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2), Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server, Ivybridge Server (GT2), Haswell Desktop (GT1), Haswell Desktop (GT2), Haswell Desktop (GT2+), Haswell Mobile (GT1), Haswell Mobile (GT2), Haswell Mobile (GT2+), Haswell Server (GT1), Haswell Server (GT2), Haswell Server (GT2+), Haswell SDV Desktop (GT1), Haswell SDV Desktop (GT2), Haswell SDV Desktop (GT2+), Haswell SDV Mobile (GT1), Haswell SDV Mobile (GT2), Haswell SDV Mobile (GT2+), Haswell SDV Server (GT1), Haswell SDV Server (GT2), Haswell SDV Server (GT2+), Haswell ULT Desktop (GT1), Haswell ULT Desktop (GT2), Haswell ULT Desktop (GT2+), Haswell ULT Mobile (GT1), Haswell ULT Mobile (GT2), Haswell ULT Mobile (GT2+), Haswell ULT Server (GT1), Haswell ULT Server (GT2), Haswell ULT Server (GT2+), Haswell CRW Desktop (GT1), Haswell CRW Desktop (GT2), Haswell CRW Desktop (GT2+), Haswell CRW Mobile (GT1), Haswell CRW Mobile (GT2), Haswell CRW Mobile (GT2+), Haswell CRW Server (GT1), Haswell CRW Server (GT2), Haswell CRW Server (GT2+), ValleyView PO board [ 18.248] (++) using VT number 8 [ 18.593] (II) intel(0): using device path '/dev/dri/card0' [ 18.593] (**) intel(0): Depth 24, (--) framebuffer bpp 32 [ 18.593] (==) intel(0): RGB weight 888 [ 18.593] (==) intel(0): Default visual is TrueColor [ 18.593] (**) intel(0): Option "AccelMethod" "uxa" [ 18.593] (--) intel(0): Integrated Graphics Chipset: Intel(R) Ivybridge Desktop (GT1) [ 18.593] (**) intel(0): Relaxed fencing enabled [ 18.593] (**) intel(0): Wait on SwapBuffers? enabled [ 18.593] (**) intel(0): Triple buffering? enabled [ 18.593] (**) intel(0): Framebuffer tiled [ 18.593] (**) intel(0): Pixmaps tiled [ 18.593] (**) intel(0): 3D buffers tiled [ 18.593] (**) intel(0): SwapBuffers wait enabled ... [ 20.312] (II) Module fb: vendor="X.Org Foundation" [ 20.312] compiled for 1.13.0, module version = 1.0.0 [ 20.312] ABI class: X.Org ANSI C Emulation, version 0.4 [ 20.312] (II) Loading sub module "dri2" [ 20.312] (II) LoadModule: "dri2" [ 20.312] (II) Module "dri2" already built-in [ 20.312] (==) Depth 24 pixmap format is 32 bpp [ 20.312] (II) intel(0): [DRI2] Setup complete [ 20.312] (II) intel(0): [DRI2] DRI driver: i965 [ 20.312] (II) intel(0): Allocated new frame buffer 1920x1080 stride 7680, tiled [ 20.312] (II) UXA(0): Driver registered support for the following operations: [ 20.312] (II) solid [ 20.312] (II) copy [ 20.312] (II) composite (RENDER acceleration) [ 20.312] (II) put_image [ 20.312] (II) get_image [ 20.312] (==) intel(0): Backing store disabled [ 20.312] (==) intel(0): Silken mouse enabled [ 20.312] (II) intel(0): Initializing HW Cursor [ 20.312] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message. [ 20.313] (**) intel(0): DPMS enabled [ 20.313] (==) intel(0): Intel XvMC decoder enabled [ 20.313] (II) intel(0): Set up textured video [ 20.313] (II) intel(0): [XvMC] xvmc_vld driver initialized. [ 20.313] (II) intel(0): direct rendering: DRI2 Enabled [ 20.313] (==) intel(0): hotplug detection: "enabled" [ 20.332] (--) RandR disabled [ 20.335] (EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found) [ 20.335] (II) intel(0): Setting screen physical size to 508 x 285 [ 20.338] (II) XKB: reuse xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm [ 20.340] (II) config/udev: Adding input device Power Button (/dev/input/event1) [ 20.340] (**) Power Button: Applying InputClass "evdev keyboard catchall" [ 20.340] (II) LoadModule: "evdev" [ 20.340] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so

    Read the article

  • Taking 10 minutes to boot up!

    - by oshirowanen
    Just added 2 pci-e to ide cards in my computer so I can use 2 old ide hard drives. Everything works fine, except the OS booting time has gone from about 10 seconds to about 10 minutes... I'f I remove both cards, it takes about 10 seconds to boot up, if I add either 1 of the cards back in, it still takes 10 seconds to boot up, but as soon as I have both cards in, it takes about 10 minutes. Why would this be happening?

    Read the article

  • Dual Monitor (Monitor and TV)

    - by umpirsky
    I connected TV to my computer, and trying to set dual display. Whatever resolution I choose for my second display (TV) I get message like this: The selected configuration for displays could not be applied required virtual size does not fit available size: requested=(2704, 1050), minimum=(320, 200), maximum=(1680, 1680) How can I fix this? Also, while I was experimenting system went to deadlock, I restarted and after boot monitor just turns off once system is up. I boot in recovery mode and after several retries fixed it somehow, I don't know how, probably by changing display config from display manager. now I found xorg.conf.new file in my home dir: Section "ServerLayout" Identifier "X.org Configured" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" RightOf "Screen0" Screen 2 "Screen2" RightOf "Screen1" InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Files" ModulePath "/usr/lib/xorg/modules" FontPath "/usr/share/fonts/X11/misc" FontPath "/usr/share/fonts/X11/cyrillic" FontPath "/usr/share/fonts/X11/100dpi/:unscaled" FontPath "/usr/share/fonts/X11/75dpi/:unscaled" FontPath "/usr/share/fonts/X11/Type1" FontPath "/usr/share/fonts/X11/100dpi" FontPath "/usr/share/fonts/X11/75dpi" FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" FontPath "built-ins" EndSection Section "Module" Load "extmod" Load "dbe" Load "glx" Load "dri" Load "dri2" Load "record" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor2" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Device" ### Available Driver options are:- ### Values: <i>: integer, <f>: float, <bool>: "True"/"False", ### <string>: "String", <freq>: "<f> Hz/kHz/MHz", ### <percent>: "<f>%" ### [arg]: arg optional #Option "NoAccel" # [<bool>] #Option "SWcursor" # [<bool>] #Option "Dac6Bit" # [<bool>] #Option "Dac8Bit" # [<bool>] #Option "BusType" # [<str>] #Option "CPPIOMode" # [<bool>] #Option "CPusecTimeout" # <i> #Option "AGPMode" # <i> #Option "AGPFastWrite" # [<bool>] #Option "AGPSize" # <i> #Option "GARTSize" # <i> #Option "RingSize" # <i> #Option "BufferSize" # <i> #Option "EnableDepthMoves" # [<bool>] #Option "EnablePageFlip" # [<bool>] #Option "NoBackBuffer" # [<bool>] #Option "DMAForXv" # [<bool>] #Option "FBTexPercent" # <i> #Option "DepthBits" # <i> #Option "PCIAPERSize" # <i> #Option "AccelDFS" # [<bool>] #Option "IgnoreEDID" # [<bool>] #Option "CustomEDID" # [<str>] #Option "DisplayPriority" # [<str>] #Option "PanelSize" # [<str>] #Option "ForceMinDotClock" # <freq> #Option "ColorTiling" # [<bool>] #Option "VideoKey" # <i> #Option "RageTheatreCrystal" # <i> #Option "RageTheatreTunerPort" # <i> #Option "RageTheatreCompositePort" # <i> #Option "RageTheatreSVideoPort" # <i> #Option "TunerType" # <i> #Option "RageTheatreMicrocPath" # <str> #Option "RageTheatreMicrocType" # <str> #Option "ScalerWidth" # <i> #Option "RenderAccel" # [<bool>] #Option "SubPixelOrder" # [<str>] #Option "ClockGating" # [<bool>] #Option "VGAAccess" # [<bool>] #Option "ReverseDDC" # [<bool>] #Option "LVDSProbePLL" # [<bool>] #Option "AccelMethod" # <str> #Option "DRI" # [<bool>] #Option "ConnectorTable" # <str> #Option "DefaultConnectorTable" # [<bool>] #Option "DefaultTMDSPLL" # [<bool>] #Option "TVDACLoadDetect" # [<bool>] #Option "ForceTVOut" # [<bool>] #Option "TVStandard" # <str> #Option "IgnoreLidStatus" # [<bool>] #Option "DefaultTVDACAdj" # [<bool>] #Option "Int10" # [<bool>] #Option "EXAVSync" # [<bool>] #Option "ATOMTVOut" # [<bool>] #Option "R4xxATOM" # [<bool>] #Option "ForceLowPowerMode" # [<bool>] #Option "DynamicPM" # [<bool>] #Option "NewPLL" # [<bool>] #Option "ZaphodHeads" # <str> Identifier "Card0" Driver "radeon" BusID "PCI:2:0:0" EndSection Section "Device" ### Available Driver options are:- ### Values: <i>: integer, <f>: float, <bool>: "True"/"False", ### <string>: "String", <freq>: "<f> Hz/kHz/MHz", ### <percent>: "<f>%" ### [arg]: arg optional #Option "ShadowFB" # [<bool>] #Option "Rotate" # <str> #Option "fbdev" # <str> #Option "debug" # [<bool>] Identifier "Card1" Driver "fbdev" BusID "PCI:2:0:0" EndSection Section "Device" ### Available Driver options are:- ### Values: <i>: integer, <f>: float, <bool>: "True"/"False", ### <string>: "String", <freq>: "<f> Hz/kHz/MHz", ### <percent>: "<f>%" ### [arg]: arg optional #Option "ShadowFB" # [<bool>] #Option "DefaultRefresh" # [<bool>] #Option "ModeSetClearScreen" # [<bool>] Identifier "Card2" Driver "vesa" BusID "PCI:2:0:0" EndSection Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" SubSection "Display" Viewport 0 0 Depth 1 EndSubSection SubSection "Display" Viewport 0 0 Depth 4 EndSubSection SubSection "Display" Viewport 0 0 Depth 8 EndSubSection SubSection "Display" Viewport 0 0 Depth 15 EndSubSection SubSection "Display" Viewport 0 0 Depth 16 EndSubSection SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Card1" Monitor "Monitor1" SubSection "Display" Viewport 0 0 Depth 1 EndSubSection SubSection "Display" Viewport 0 0 Depth 4 EndSubSection SubSection "Display" Viewport 0 0 Depth 8 EndSubSection SubSection "Display" Viewport 0 0 Depth 15 EndSubSection SubSection "Display" Viewport 0 0 Depth 16 EndSubSection SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Card2" Monitor "Monitor2" SubSection "Display" Viewport 0 0 Depth 1 EndSubSection SubSection "Display" Viewport 0 0 Depth 4 EndSubSection SubSection "Display" Viewport 0 0 Depth 8 EndSubSection SubSection "Display" Viewport 0 0 Depth 15 EndSubSection SubSection "Display" Viewport 0 0 Depth 16 EndSubSection SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Can I delete it? Second display (TV) only works when I check Mirror displays option.

    Read the article

  • Ubuntu 12.04 can't detect internal mobile broadband (Gobi 2000)

    - by Anega
    Hi I have been trying Ubuntu to detect and connect using the buit in mobile broadband capability in my HP 110 netbook but until now nothing seems to work Output of lspci command: 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [AHCI mode] (rev 02) 01:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) 02:00.0 Ethernet controller: Atheros Communications Inc. AR8132 Fast Ethernet (rev c0) Output of lsusb command: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 1fea:0008 Bus 005 Device 002: ID 03f0:2a1d Hewlett-Packard Bus 001 Device 005: ID 03f0:241d Hewlett-Packard Gobi 2000 Wireless Modem (QDL mode) So far I have been trying what is intended on several pages, trying to update firmware using wine and then moving .mda or whatever files the update package GobiInstaller.mdi throws out. The results are always the same: After running Output of wine msiexec /a GobiInstaller.msi /qb TARGETDIR="c:\temp" fixme:advapi:GetCurrentHwProfileA (0x33fba8) semi-stub fixme:heap:HeapSetInformation (nil) 1 (nil) 0 fixme:win:RegisterDeviceNotificationA (hwnd=0x13e250, filter=0xf7e984,flags=0x00000001) returns a fake device notification handle! fixme:heap:HeapSetInformation (nil) 1 (nil) 0 fixme:heap:HeapSetInformation (nil) 1 (nil) 0 fixme:advapi:RegisterEventSourceW ((null),L"Bonjour Service"): stub fixme:advapi:ReportEventA (0xcafe4242,0x0004,0x0000,0x00000064, (nil),0x0001,0x00000000,0x79e58c,(nil)): stub fixme:advapi:ReportEventW (0xcafe4242,0x0004,0x0000,0x00000064, (nil),0x0001,0x00000000,0x12e6d0,(nil)): stub fixme:winsock:WSAIoctl WS_SIO_UDP_CONNRESET stub fixme:winsock:WSAIoctl -> SIO_ADDRESS_LIST_CHANGE request: stub fixme:iphlpapi:DeleteIpForwardEntry (pRoute 0x79e920): stub fixme:iphlpapi:CreateIpForwardEntry (pRoute 0x79e958): stub fixme:advapi:ReportEventA (0xcafe4242,0x0004,0x0000,0x00000064, (nil),0x0001,0x00000000,0x79e58c,(nil)): stub fixme:advapi:ReportEventW (0xcafe4242,0x0004,0x0000,0x00000064, (nil),0x0001,0x00000000,0x12e6d0,(nil)): stub fixme:service:EnumServicesStatusW resume handle not supported fixme:service:EnumServicesStatusW resume handle not supported fixme:advapi:ReportEventA (0xcafe4242,0x0004,0x0000,0x00000064,(nil),0x0001,0x00000000,0x79e58c,(nil)): stub fixme:advapi:ReportEventW (0xcafe4242,0x0004,0x0000,0x00000064, (nil),0x0001,0x00000000,0x12e6d0,(nil)): stub fixme:netapi32:NetGetJoinInformation Semi-stub (null) 0x79e644 0x79e63c fixme:winsock:WSAIoctl WS_SIO_UDP_CONNRESET stub fixme:storage:create_storagefile Storage share mode not implemented. err:msi:ITERATE_Actions Execution halted, action L"_693CD41C_A4A2_4FA1_8888_FC56C9E6E13B" returned 1603 err:rpc:I_RpcGetBuffer no binding err:rpc:I_RpcGetBuffer no binding andres@andres-HP-Mini-110-1100:~/.wine/drive_c/Qualcomm$ fixme:advapi:ReportEventA (0xcafe4242,0x0004,0x0000,0x00000064,(nil),0x0001,0x00000000,0x79e588,(nil)): stub fixme:advapi:ReportEventW (0xcafe4242,0x0004,0x0000,0x00000064, (nil),0x0001,0x00000000,0x12e6d0,(nil)): stub And creates 2 empty folders, I have been trying hard and I am not sure if I am doing it the way it should be. Thanks

    Read the article

  • How to detect Creative Sound blaster Audigy 2?

    - by Chris
    I have installed a pci 7.1 sound card Creative Sound Blaster Audigy 2, on my 10.10 Ubuntu 64 bit installation. I have disabled the on board sound card from bios. I boot and the system cannot recognize my "new" sound card. When I execute aplay -l I get this responce: aplay: device_list:235: no soundcards found... I take a guess and I think it is probably something wrong with my sound modules.

    Read the article

  • How to update coffee script?

    - by Tetsu
    I got a following error when I tried to watch coffee scripts by coffee -o js -cw coffee. /usr/local/lib/node_modules/coffee-script/lib/coffee-script/command.js:321 throw e; ^ Error: watch Unknown system errno 28 at errnoException (fs.js:636:11) at FSWatcher.start (fs.js:663:11) at Object.watch (fs.js:691:11) at /usr/local/lib/node_modules/coffee-script/lib/coffee-script/command.js:287:27 at Object.oncomplete (/usr/local/lib/node_modules/coffee-script/lib/coffee-script/command.js:100:11) I have no idea what is going with error. Then I checked the versions, coffee -v is 1.6.1 and node -v is v0.6.12. According the official site( http://coffeescript.org/ ) the latest version is 1.6.3, so I wanted update coffee by npm update -g coffee-script, but this fails also. npm WARN [email protected] package.json: bugs['name'] should probably be bugs['url'] npm http GET https://registry.npmjs.org/coffee-script npm http 304 https://registry.npmjs.org/coffee-script How can I update coffee script? Edit 2013/10/11 In my coffee script directory there is only one file box_wrapper.coffee. $ -> $("body").children().wrap -> "<div id='#{$(@).attr "id"}_box' class='wrapper'/>" Edit 2013/10/16 I tried to re-install coffee, so I've done like this. $ sudo npm -g rm coffee npm WARN Not installed in /usr/local/lib/node_modules coffee $ coffee -v CoffeeScript version 1.6.1 I can't remove coffee. And I tried also like this. $ sudo apt-get remove npm $ npm -v -bash: /usr/bin/npm: No such file or directory $ sudo apt-get install npm $ npm -v 1.1.4 $ sudo npm -g install coffee # I omit a lot of `GET` parts. npm http 304 https://registry.npmjs.org/mkdirp/0.3.4 npm ERR! error installing [email protected] npm http 304 https://registry.npmjs.org/assertion-error/1.0.0 npm http 304 https://registry.npmjs.org/growl npm http 304 https://registry.npmjs.org/jade/0.26.3 npm http 304 https://registry.npmjs.org/diff/1.0.2 npm http 304 https://registry.npmjs.org/mkdirp/0.3.5 npm http 304 https://registry.npmjs.org/glob/3.2.1 npm http 304 https://registry.npmjs.org/ms/0.3.0 npm ERR! error rolling back [email protected] Error: UNKNOWN, unknown error '/usr/local/lib/node_modules/coffee/node_modules/express' npm ERR! error installing [email protected] npm ERR! EEXIST, file already exists '/usr/local/lib/node_modules/coffee/node_modules/mocha/node_modules' npm ERR! File exists: /usr/local/lib/node_modules/coffee/node_modules/mocha/node_modules npm ERR! Move it away, and try again. npm ERR! npm ERR! System Linux 3.2.0-54-generic-pae npm ERR! command "node" "/usr/bin/npm" "-g" "install" "coffee" npm ERR! cwd /home/ironsand npm ERR! node -v v0.6.12 npm ERR! npm -v 1.1.4 npm ERR! path /usr/local/lib/node_modules/coffee/node_modules/mocha/node_modules npm ERR! fstream_path /usr/local/lib/node_modules/coffee/node_modules/mocha/node_modules/___debug.npm npm ERR! fstream_type Directory npm ERR! fstream_class DirWriter npm ERR! code EEXIST npm ERR! message EEXIST, file already exists '/usr/local/lib/node_modules/coffee/node_modules/mocha/node_modules' npm ERR! errno {} npm ERR! fstream_stack /usr/lib/nodejs/fstream/lib/writer.js:161:23 npm ERR! fstream_stack Object.oncomplete (/usr/lib/nodejs/mkdirp.js:34:53) npm ERR! EEXIST, file already exists '/usr/local/lib/node_modules/coffee/node_modules/mocha/node_modules' npm ERR! File exists: /usr/local/lib/node_modules/coffee/node_modules/mocha/node_modules npm ERR! Move it away, and try again. npm ERR! npm ERR! System Linux 3.2.0-54-generic-pae npm ERR! command "node" "/usr/bin/npm" "-g" "install" "coffee" npm ERR! cwd /home/ironsand npm ERR! node -v v0.6.12 npm ERR! npm -v 1.1.4 npm ERR! path /usr/local/lib/node_modules/coffee/node_modules/mocha/node_modules npm ERR! fstream_path /usr/local/lib/node_modules/coffee/node_modules/mocha/node_modules/___debug.npm npm ERR! fstream_type Directory npm ERR! fstream_class DirWriter npm ERR! code EEXIST npm ERR! message EEXIST, file already exists '/usr/local/lib/node_modules/coffee/node_modules/mocha/node_modules' npm ERR! errno {} npm ERR! fstream_stack /usr/lib/nodejs/fstream/lib/writer.js:161:23 npm ERR! fstream_stack Object.oncomplete (/usr/lib/nodejs/mkdirp.js:34:53) npm ERR! npm ERR! Additional logging details can be found in: npm ERR! /home/ironsand/npm-debug.log npm not ok And npm-debug.log is a blank file.

    Read the article

  • Linux kernel regression on power usage

    - by dago
    Webupd8 reported this power management fix for the 2.6.38 Linux kernel regression: Add the following to the boot grub line "pcie_aspm=force" My question - how does this suggested fix differ from this hint from powertop: Suggestion: Enable Device Power Management by pressing the P key, which execute the following action: find /sys/devices/pci* -path "*power/control" -exec bash -c "echo auto > '{}'" \;

    Read the article

  • Is Infiniband going to get squeezed by iWARP and external QPI?

    - by andy.grover
    The Inquirer certainly thinks so.However, I'm not so sure it makes sense to compare Infiniband to an as-yet-unannounced optical external QPI. QPI is currently a processor interconnect. CPUs, RAM, and devices connected by it are conceptually part of the same machine -- they run a single OS, for example. They are both "networks" or "fabrics" but they have very different design trade-offs.Another widely-used bus in the system is closer to Infiniband than QPI -- PCI Express. Isn't it more likely that PCIe could take on IB? There are companies already who have solutions that use external PCI Express for cluster interconnect, but these have not gained significant market share. Why would QPI, a technology whose sweet spot is even further from Infiniband's than PCIe, be able to challenge Infiniband? It's hard to speculate without much information, but right now it doesn't seem likely to me.The other prediction made in the article is that Intel's 10GbE iWARP card could squeeze IB on the low end, due to its greater compatibility and lower cost.It's definitely never a good idea to bet against Ethernet when it comes to mass-market, commodity networking. Ethernet will win. 10GbE will win. But, there are now two competing ways to implement the low-latency RDMA Verbs interface on top of Ethernet. iWARP is essentially RDMA over TCP/IP over Ethernet. The new alternative is IBoE (Infiniband over Ethernet, aka RoCEE, aka "Rocky"). This encapsulates the IB packet protocol directly in the Ethernet frame. It loses the layer 3 routability of iWARP, but better maintains software compatibility with existing apps that use IB, and is simpler to implement in both software and hardware. iWARP has a substantial head start, but I believe that IBoE silicon will eventually be cheaper, and more likely to be implemented in commodity Ethernet hardware.I think IBoE is going to take low-end market share from traditional IB, but I think this is a situation IB hardware vendors have no problem accepting. Commoditized IBoE NICs invite greater use of RDMA features, and when higher performance is needed, customers can upgrade to "real" IB, maintaining IB's justification for higher prices. (IB max interconnect speeds have historically been 2-4x higher than Ethernet, and I don't see that changing.)(ObDisclosure: My current employer now sells IB hardware. I previously also worked at Intel. My opinions are my own, duh.)

    Read the article

  • What are these errors when I try to "make" the driver of my wireless adapter?

    - by Tom Brito
    I got got a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme says to use the make command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g

    Read the article

  • ubuntu 13.04 recognizes usb mobile broadband modem as ethernet connection

    - by Bence Mihalka
    When I plug in my usb mobile broadband modem (ZTE MF-667), in the network manager instead of a mobile broadband connection, I get an ethernet connection, called: Ethernet Network (ZTE WCDMA Technologies MSM), which of course doesn't work. Here is my lsusb output and the relevant parts of dmesg output: lsusb: Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0cf3:3005 Atheros Communications, Inc. AR3011 Bluetooth Bus 001 Device 004: ID 04f2:b1b9 Chicony Electronics Co., Ltd Asus Integrated Webcam Bus 001 Device 005: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 002 Device 004: ID 19d2:1405 ZTE WCDMA Technologies MSM dmesg: [ 195.328467] usb 2-1.1: new high-speed USB device number 3 using ehci-pci [ 195.423545] usb 2-1.1: New USB device found, idVendor=19d2, idProduct=1225 [ 195.423555] usb 2-1.1: New USB device strings: Mfr=3, Product=2, SerialNumber=4 [ 195.423561] usb 2-1.1: Product: ZTE WCDMA Technologies MSM [ 195.423567] usb 2-1.1: Manufacturer: ZTE,Incorporated [ 195.423572] usb 2-1.1: SerialNumber: P680A1ZTED000000 [ 195.426319] scsi7 : usb-storage 2-1.1:1.0 [ 196.425354] scsi 7:0:0:0: CD-ROM CWID USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2 [ 197.447919] usb 2-1.1: USB disconnect, device number 3 [ 197.457582] sr0: scsi3-mmc drive: 243x/186x xa/form2 cdda pop-up [ 197.457594] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 197.459058] sr 7:0:0:0: Attached scsi CD-ROM sr0 [ 197.459483] sr 7:0:0:0: Attached scsi generic sg2 type 5 [ 197.759186] usb 2-1.1: new high-speed USB device number 4 using ehci-pci [ 197.854543] usb 2-1.1: New USB device found, idVendor=19d2, idProduct=1405 [ 197.854556] usb 2-1.1: New USB device strings: Mfr=4, Product=3, SerialNumber=5 [ 197.854564] usb 2-1.1: Product: ZTE WCDMA Technologies MSM [ 197.854572] usb 2-1.1: Manufacturer: ZTE,Incorporated [ 197.854579] usb 2-1.1: SerialNumber: P680A1ZTED010000 [ 197.957739] scsi8 : usb-storage 2-1.1:1.2 [ 198.076554] cdc_ether 2-1.1:1.0 eth1: register 'cdc_ether' at usb-0000:00:1d.0-1.1, CDC Ethernet Device, 00:a0:c6:00:00:00 [ 198.076583] usbcore: registered new interface driver cdc_ether [ 198.955985] scsi 8:0:0:0: CD-ROM CWID USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2 [ 198.956797] scsi 8:0:0:1: Direct-Access ZTE MMC Storage 2.31 PQ: 0 ANSI: 2 I created the appropriate mobile broadband connection manually, but I cannot enable it in network manager, since the device is not recognized as mobile broadband. Any tips how to make it work?

    Read the article

< Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >