Search Results

Search found 33223 results on 1329 pages for 'database firewall'.

Page 612/1329 | < Previous Page | 608 609 610 611 612 613 614 615 616 617 618 619  | Next Page >

• Windows Server 2003: Nat Port Forwarding Not Working

  - by jM2.me

  The setup is following: Internet (108.99.XXX.XX) <- Windows Server 2003 (10.0.0.1) <- Switch <- Office Computers (10.0.0.100-200 some static routes some manual some automatic) Windows Server has NAT installed on it and two network interfaces are configured properly. The problem is, whenever I try to forward port 80 (or any other) from office computer (lets say 10.0.0.100), it fails. Nic #1 Settings: All settings are obtained from ISP Nic #2 Settings: Set manually IP: 10.0.0.1 Mask: 255.255.255.0 Nat Server is configured to automatically assign IP addresses to private network. Settings are: IP: 10.0.0.0 Mask: 255.255.255.0 Forwarding was done in Routing and Remote Access (local) - IP Routing - NAT/Basic Firewall - Local Area Connection (right click_properties) - services and ports - Web Server HTTP - Private Address: 10.0.0.100 SO what is causing the problem of failure to forward any port from other computer inside private network?

  Read the article

• Random timeout now and then

  - by KenavR

  Maybe this is a to generic question, but since we have this issue for quite a while now, I give it a shot. We have some applications which use HTTP for the connection between the client (website or fat-client) and the server. The Computer who runs this applications is in a Network behind a firewall and a proxy, the server isn't inside the same network. The problem is that every now and then the https Request times out and depending on the Client the Application "hangs" or does some other funky stuff. The problem is definitely inside our network, because if i try the applications outside our network it works fine. Can you give me a hint where i can most likely find the problem?

  Read the article

• Is it possible to connect these machines with ssh tunnels or another mechanism?

  - by frankc

  I am physically on a machine that is behind a firewall and cannot be ssh'd into. Let's call that PC. PC can connect out to two machines, one on AWS and one that is part of a vpn connection, call them A and V, respectively. A and V cannot talk to each other directly. I need to frequently move files between A and V and have been doing this by scp'ing to PC and then scp'ing from pc. Is there a better way to do this? A and V are linux but PC has cygwin.

  Read the article

• Is A Managed Switch With VLAN Support Required

  - by Justin

  Hello, I am wondering if I need to buy a switch which is managed (VLAN support) for my configuration, or will a cheaper unmanaged switch work? I have servers with two NICS each. The first NIC is public and the second NIC is private. The router will plug into the switch port 1 let's say (public). Then server 1 public plugs into port 2 on the switch, and sever 1 private plugs into port 3 on the switch. The public interface is: 192.168.X.X / 255.255.0.0 and the private interface is 10.0.X.X / 255.255.0.0. So looks like: ** SWITCH ** Port Device Network 1 Router/Firewall 192.168.X.X 2 Server 1 Public 192.168.X.X 3 Server 1 Private 10.0.X.X 4 Server 2 Public 192.168.X.X 5 Server 2 Private 10.0.X.X 6 Server 3 Public 192.168.X.X 7 Server 3 Private 10.0.X.X Thanks.

  Read the article

• Exchange over HTTP

  - by Rob

  I have recently setup a brand new install of SBS 2011 and it is working well. Exchange is running as advertised and all users are happy. Now, there are 2 users who would like to work outside of the office and require email setting up in Outlook. No problem - Exchange over HTTP. However for some reason it's not working. They can access Outlook Web Access okay, but for some reason Exchange over HTTP / HTTPS isn't working. The error message I receive in Outlook is: "The name cannot be resolved. The connection to Microsoft Exchange is unavailable. Outlook must be online or connected to complete this action." I've tried temporarily turning off the Firewall on both the server and the client but this doesn't help at all. Is there something I'm missing or is there a permission that needs enabling to allow Exchange over HTTP to work?? Many thanks

  Read the article

• I am trying to setup phpMyAdmin to use with a remote MySQL databases on Scientific Linux release 6.2

  - by techsjs2012

  I am trying to setup phpMyAdmin to use with a remote MySQL databases on Scientific Linux release 6.2. If I use the mysql command line to connect to the remote database it works great but if I use mysqladmin I am getting "#2002 Cannot log in to the MySQL server". I have found if I do a: setenforce 0 It will work from myphpadmin to my remote database but once I reboot or set Scientific Linux setenforce back to one it stops working again.. I know setenforce 0 is not the right thing to do but can someone please give me details steps on how to get this working the right way... thanks I am new to Scientific Linux and been having some issues.. thanks

  Read the article

• Clean out a large MediaWiki text table

  - by Bart van Heukelom

  I just discovered that an old MediaWiki of mine was infested with spam, and the database table named "text" (which contains the page content) is 3GB large. I've deleted all the spam pages manually, but: The table is still the same size. I wonder how it got to 3GB anyway. There wasn't that much spam (about a hundred medium-sized pages) How can I get rid of this mess? If you want to inspect the wiki, it's over here. The database is MySQL 5.0.75.

  Read the article

• LDAP replication breaking referrals

  - by MasterZ

  We have an issue that we believe is caused by ldap replication changing the port of the referal from 686 (secure) to 389 (unsecure). If we setup a new referral everything works, but then as soon as we change someone's password it changes on the master, and then the master replicates and the referral breaks. Any further attempts to modify someone's account give the error "PAM: Cannot connect to LDAP". We used snoop and monitored the firewall to see what was going on. The first password attempt (the one that works) goes over port 686 (as it is supposed to) but every subsequent attempt attempts to use port 389, and therefore fails. We only have 1 referral configured on the client, port 686

  Read the article

• Is there a direct URL to download Java JDK updates?

  - by Bob Cross

  I have a whole set of machines that are on the other side of a firewall configured to prevent all Javascript from functioning. All of them (Linux 32 and 64 bit configurations) must be updated to Java 6 update 20. This is a problem given Sun/Oracle's URL redirector and download manager: they simply don't appear or don't work. Is there a URL to download the JDK updates and bypass the redirect? Obviously, a yum configuration that would allow for automatic updates would be optimal but I'd be happy to just have the rpm file.

  Read the article

• Does TFS 2010 lock a project collection when it's being cloned?

  - by Hirvox

  We're planning to migrate a project collection currently hosted on TFS 2010 to TFS 2012. We want to keep the current installation running while resolving any issues that might arise, so we need to copy the current project collection to the new server. However, TFS doesn't allow us to attach a restored database backup directly. The database first must be detached from the original TFS installation. We can get around that limitation by cloning the project collection and detaching the clone, but we're not sure whether that would also impact the original project collection. Does TFS lock the original project collection while it's being cloned?

  Read the article

• Bad password when logging in via Remote Desktop

  - by Shiraz Bhaiji

  I have just setup a windows 2003 server running in hyper-V. When I log in via Hyper-V it works fine. When I try to login via remote desktop I get a bad user name or password error. I have: Disabled the firewall Enabled remote connections Before I did the above I did not get to the login screen. I can ping the ip address of the image. I am trying to login as Administrator. Anyone have an idea about how to fix this? Edit I have now managed to fix this by changing the password to something without special characters. Strange thing is the I could not see any problems with the passord, had tried typing it into the user name field to check it.

  Read the article

• "The requested operation could not be completed due to a file system limitation" 3202

  - by user46529

  I backup SQL Server database and it fails BACKUP DATABASE dd TO DISK = '\backupServer\backups\dd.bak' WITH COMPRESSION, CHECKSUM, NOFORMAT, INIT , BlockSize = 65536 , BufferCount = 2200 , MaxTransferSize = 4194304 The backup size is 3TB and I have 6TB free space on bacup server. I am using backup parameters per SQLCAT whitepaper. Everything works ok when I backup to local HDD and it always fails when I backup to network share. After about 6 hours. Can't find why. Thank you. Yes. The backup over the network is fastest and saves me 3Tb of local disk space :) Thanks for pointing to the memory issue. I left 4Gb to OS and it worked!

  Read the article

• Losing WLAN connections but maintaining internet connections on WIndows 7 Workgroup

  - by Di

  I have 4 computers all running Windows 7 networked in a Work group through Billion 7404vgp-m wireless router. All drivers and firmware for wireless adapters and router are up to date. Windows Firewall and Defender disabled. Disconnected ipv6. Running Nod 32 anti virus software. All have own static IP address 192.XXX.X.XXX. When I Reset the router all computers have Internet and LAN access for about 1 hour and then they will lose the LAN connection but maintain Internet connection. Resetting wireless adapters or restarting computers does nothing to fix this but resetting router will. What is causing this? How do I fix it?

  Read the article

• Exchange 2007 OWA not listening on SSL port

  - by krs1

  I have an Exchange 2007 server that went down after a power failure. It has OWA access via SSL both externally and internally. OWA is working fine from the internal notwork, however I am getting a timeout when I attempt to connect externally. I pulled up wireshark and noticed that the server actually redirects to SSL. For some reason the server is not listening on the SSL port, and this seems to be causing the timeout. I normally do only development work, but I'm stuck with this since my sysadmin took off for the week and isn't answering my phone calls. As far as I know it shouldn't be a firewall issue. Aside from me not wanting to work on the damn thing, what should I look for?

  Read the article

• ubuntu server refusing connections via port forwarding

  - by Matt

  Getting some really weird behavior from our Ubuntu server... it's behind a Verizon router firewall with port forwarding (port 8080 to port 80 on the server), and we've been having issues accessing it via this external IP. From within the network, it appears to respond normally (I can access it via web browser and SSH), but refuses connections through port forwarding (using our static external IP). The strangest thing is that it actually responds to external port-forwarded connections right after being restarted, but quickly lapses back into this pattern of refusing external connections. I'm a bit of a server newbie (I'm actually a programmer in a small startup that just lost their server ops guy, urgh) so this is all trial by fire for me. Does anyone have any advice on what could be going wrong here? Any help would be appreciated, thanks.

  Read the article

• Homegroup libraries visible but can't be opened

  - by majocha

  I have 2 Windows 7 PCs in a home network. When I create a homegroup, the libraries I share are visible on the opposing machine but when I doubleclick them nothing happens - no error message, nothing at all. It is the same on both computers. The homegroup works to the extent that the printer I shared is visible and can print from the other computer. Only the libraries are inaccessible. What I tried and checked so far, without result: disabling firewall file and printer sharing, MS Networks client enabled in network properties deleting and recreating homegroup reset homegroup by deleting C:\Windows\ServiceProfiles\LocalService\AppData\Roaming\PeerNetworking unsharing and sharing again the libraries

  Read the article

• Can you convert an address to a zip code in a spreadsheet?

  - by moe37x3

  Given a column of street addresses with city and state but no zip in a spreadsheet, I'd like to put a formula in a second column that yields the ZIP code. Do you know a way to do this? I'm dealing with US addresses, but answers pertaining to other countries are interesting, too. UPDATE: I guess I'm mostly hoping that there's a way to do this in Google Spreadsheets. I realize that you need to access a vast ZIP code database to do this, but it seems to me that such a database is already inside Google Maps. If I put an address in there without ZIP code, I get back an address with ZIP code. If Maps can do that lookup, maybe there's a way to make it happen in Spreadsheets, too.

  Read the article

• RV042 - how to broadcast UDP through VPN

  - by user47221

  I setup a gateway to gateway vpn connection with linksys RV042 router. i was able to ping each other, access file sharing ( with netbios enabled ). They are having same subnet mask 255.255.255.0, 192.168.1.0 <--- 192.168.2.0 Firewall disabled. But when i created/host LAN games (eg. warcraft3), it cannot be detect by clients at another site/LAN. As i know warcraft3 is using UDP broadcast to tell the client the game is creaetd. 1. How to broadcast UDP to another LAN ? any things to do with multicast ?

  Read the article

• Gmail/Facebook/Hotmail not opening in Firefox/IE on Windows 7 Home

  - by singlepoint

  Hi, I am unable to open Gmail/Facebook/Hotmail on Firefox/IE on Widows 7 Home. I just unboxed a brand new hp laptop with Norton Security Suite running inside. I get following error message on Firefox. Please help. The connection has timed out The server at www.google.com is taking too long to respond. * The site could be temporarily unavailable or too busy. Try again in a few moments. * If you are unable to load any pages, check your computer's network connection. * If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web

  Read the article

• MS Access 2007 end user access

  - by LtDan

  I need some good advise. I have used Access for many years and I use Sharepoint but never the two combined. My newly created Access db needs to be shared with many users across the organization. The back end is SQL and the old way to distribute the database would be placing the db on a shared drive, connecting their PC ODBC connections to the SQL db and then they would open the database and have at it. This has become the OLD way. What is the best (and simpliest) way to allow the end users to utilize a frontend for data entry/edit reporting etc. Can I create a link through SharePoint and the user just open it from there. Your good advise is greatly approciated.

  Read the article

• VPN Authentication Credentials (Local/Remote Identifiers) For Remote Access VPN

  - by thatidiotguy

  So I am trying to set up a remote access VPN using the free ShrewSoft vpn client: https://www.shrew.net/software I want to use a PSK as the authentication mechanism combined with XAuth so that a connection requires a valid username/pass combo. Under the authentication tab this particular VPN Client however is asking for a Local Identity and a Remote Identity. The options for Local Identity Type are: Fully Qualified Domain Name User Fully Qualified Domain Name IP Address Key Identifier The options for Remote Identity are: Any Fully Qualified Domain Name User Fully Qualified Domain Name IP Address Key Identifier My current thinking is that I can use the Fully Qualifed Domain Name provided by the remote firewall for the Remote Identity, but I do not know what it wants for local identity. Just to stress: I am not trying to set up a site to site VPN. Can anybody shed any light on what I am missing here? A screenshot can be provided if that would be helpful. The current error I am getting during the connection is: IKE Responder: Proposed IKE ID mismatch

  Read the article

• Can ping cannot be pinged

  - by slayerIQ

  Today, I installed my new router so I can connect my other pc and my ps3. In my network, there are some other computers these are connected with each other through another router. So I have one modem with 2 routers that make up my network. Everything works fine the only problem I am having is being pinged by other computers in the network. All the computers are on the same subnet 255.255.255.0. There is no problem with my firewall or anything I tested everything. How can i solve this?

  Read the article

• Url-based web site publishing on Windows Server platform

  - by Maxim V. Pavlov

  I have a Windows 2008 Enterprise SP2 server in a datacenter. It is 32bit OS. I need to be able to do a "smart" url-based web site publishing. So that with a single external IP I can publish many sites on port 80, and some firewall logic resolves, based on a requested URL, which site in IIS gets the request. Forefront TMG 2010 has this feature, but it is not supported on 32bit systems. Is there a software solution that can satissfy my need on Windows 2K8 platform? Thank you. P.S. Perhaps there is a workaround or a tweak to do what I need in IIS?

  Read the article

• Vista Home Premium won't upload

  - by longhairedsi

  Hi, I have a sony vaio laptop(VGN-FW31J) running windows Vista Home Premium . I've had it over a year and file upload in a browser has never worked on any website in any browser(IE, Firefox, Chrome). I can select a file and the upload starts running but I always get a timeout. Sometimes it has worked once out of many attempts but only if the file is very small( < 50k). FTP does work. I've tried the following: Disabling anti virus Disabling firewall Can anyone help me here? i'm wondering if this is a vista problem or a vaio problem. Cheers

  Read the article

• Where are going contacts entered in iNotes

  - by PeterMmm

  When i enter a contact in iNotes in what database they are going and can i access them from native Notes Client ?

  Read the article

< Previous Page | 608 609 610 611 612 613 614 615 616 617 618 619  | Next Page >