Search Results

Search found 16587 results on 664 pages for 'virtual hardware'.

Page 615/664 | < Previous Page | 611 612 613 614 615 616 617 618 619 620 621 622  | Next Page >

• HP DAT72x6 autoloader

  - by ericmayo

  Hoping someone here has seen this similar issue and can offer soem advise... I have an HP DAT72x6 auto loader tape backup unit. The external kind, here is a link to an owner's manual I found of it. http://www.dectrader.com/docs/set2/emr_na-c00070400-1.pdf I purchased the unit used about 6 months ago. The unit stopped working after 3-4 back-ups, it's used one day a month to do a monthly backup of another system. Suffice it to say the unit gets very little usage. There is an amber light on the front of the unit called the OAR (Operator Attention Required). The manual states to call for service when this light comes on and stays on. I've tried a few things to resolve but none are working. I've tried power cycling, re-securing the SCSI cables at both ends. Unit was used so I didn't pay much ($500) and so I don't want to spend a lot to have it fixed; might as well buy something new one if fixing this is going to cost more than $100-$150 bucks. I'm curious to see if anyone here has been around these devices or possibly is an HP repair person that can give me some things to try to resolve. The manual states that a solid amber OAR light indicates a hardware failure. When I power cycle the unit I see one of two scenarios so far. The unit powers up, shows self test in the LCD, then LCD changes to show all possible images and the OAR light comes on. The unit powers up, LCD is completely blank, the green lights go through some sort of process of going on and off and later the amber OAR light comes on and stays on. If it's a simple misalignment issue, I may be able to fix myself but not knowing what could cause the OAR light to come on gives me no where to even start. Google around gave no help either. I hoping someone here has experience with this and can help or point me in the right direction. Also, I don't have the HP Diagnostic tools mentioned in many manuals. The unit is connected to a Linux box. The 3-4 backups I've done with it so far have had no issues. We run amanda backup. Before this incident the unit was backing up and reading tapes fine. Thanks for any help or suggestions.

  Read the article

• libvirt qemu/kvm migration problem

  - by Panda

  I am using kvm and libvirt on my Dell server. Now i am trying to migrate one virtual machine from a physical server to another. However, I failed everytime. In virsh on physicalServer1, I typed: virsh # migrate virtualmachine1 qemu+ssh://username@physicalServer2/system error: operation failed: migration to 'tcp:physicalServer2:49163' failed: migration failed Then I searched FAQ part on libvirt.org. It says: error: operation failed: migration to '...' failed: migration failed This is an error often encountered when trying to migrate with QEMU/KVM. This typically happens with plain migration, when the source VM cannot connect to the destination host. You will want to make sure your hosts are properly configured for migration (see the migration section of this FAQ) I managed to ssh physicalServer2 from a shell on virtualmachine1 so the above red part did not explain my failure. I also open ports on physicalServer2, iptables -L shows following information: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps ACCEPT tcp -- anywhere anywhere state NEW tcp dpts:49152:49215 Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination The /var/log/libvirt/qemu/virtualmachine1.log on physicalServer2: 2011-05-06 13:37:30.708: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-0.14 -enable-kvm -m 2048 -smp 1,sockets=1,cores=1,threads=1 -name openjudge-test -uuid a8c704bc-a4f9-90db-3e57-40e60b00aac1 -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/virtualmachine1.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=readline -rtc base=utc -boot c -drive file=/media/nfs/virtualmachine1.img,if=none,id=drive-ide0-0-0,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -netdev tap,fd=20,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=00:16:36:8a:22 :a0,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -usb -vnc 127.0.0.1:2 -vga cirrus -incoming tcp:0.0.0.0:49163 -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 char device redirected to /dev/pts/0 2011-05-06 13:37:30.915: shutting down The /var/log/libvirt/qemu/virtualmachine1.log on physicalServer1 is empty. Both physical servers are using Ubuntu 11.04. The libvirt and kvm used are installed by apt-get. The libvirt version is 0.8.8.

  Read the article

• Why do I see a large performance hit with DRBD?

  - by BHS

  I see a much larger performance hit with DRBD than their user manual says I should get. I'm using DRBD 8.3.7 (Fedora 13 RPMs). I've setup a DRBD test and measured throughput of disk and network without DRBD: dd if=/dev/zero of=/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 4.62985 s, 116 MB/s / is a logical volume on the disk I'm testing with, mounted without DRBD iperf: [ 4] 0.0-10.0 sec 1.10 GBytes 941 Mbits/sec According to Throughput overhead expectations, the bottleneck would be whichever is slower, the network or the disk and DRBD should have an overhead of 3%. In my case network and I/O seem to be pretty evenly matched. It sounds like I should be able to get around 100 MB/s. So, with the raw drbd device, I get dd if=/dev/zero of=/dev/drbd2 bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 6.61362 s, 81.2 MB/s which is slower than I would expect. Then, once I format the device with ext4, I get dd if=/dev/zero of=/mnt/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 9.60918 s, 55.9 MB/s This doesn't seem right. There must be some other factor playing into this that I'm not aware of. global_common.conf global { usage-count yes; } common { protocol C; } syncer { al-extents 1801; rate 33M; } data_mirror.res resource data_mirror { device /dev/drbd1; disk /dev/sdb1; meta-disk internal; on cluster1 { address 192.168.33.10:7789; } on cluster2 { address 192.168.33.12:7789; } } For the hardware I have two identical machines: 6 GB RAM Quad core AMD Phenom 3.2Ghz Motherboard SATA controller 7200 RPM 64MB cache 1TB WD drive The network is 1Gb connected via a switch. I know that a direct connection is recommended, but could it make this much of a difference? Edited I just tried monitoring the bandwidth used to try to see what's happening. I used ibmonitor and measured average bandwidth while I ran the dd test 10 times. I got: avg ~450Mbits writing to ext4 avg ~800Mbits writing to raw device It looks like with ext4, drbd is using about half the bandwidth it uses with the raw device so there's a bottleneck that is not the network.

  Read the article

• Why is vCenter 5.1u1 exiting hosts from maintenance mode?

  - by Shane Madden

  This vCenter server was just upgraded to 5.1 update 1. I'm going through hosts and bringing firmware up to date, then upgrading them from various versions of 5.0 to 5.1u1. vCenter 5.1u1 seems to have an interesting new behavior: it's removing hosts from maintenance mode when they reconnect after being disconnected -- but very inconsistently, I've seen it maybe 4 or 5 times on ~25-30 host reboots. I've only seen it happen on 5.0 hosts that have not yet been upgraded to 5.1. In the image, I placed the host in maint mode and rebooted it into the HP SPP DVD's automatic update mode. After its usual ~40 minute update process, the host came back online.. and 7 seconds before even logging that the host had reconnected, vCenter had sent the host a task to exit maintenance mode. In my understanding, the only time vCenter should drop a host out of maintenance mode is when vCenter put it into maintenance mode itself (such as a VUM upgrade task). Why would this vCenter be unilaterally exiting a host from user-initiated maintenance mode? Edit, additional info: I ran the firmware upgrades on 5 more hosts, all at the same time. Two of them exited maint mode after reconnecting, three did not. The common factor of those exiting maint mode seems to be how long they were offline; the two that took a few tries to boot to the virtual media are the two that got knocked out of maint mode. esx31 (image above): 45 minutes unresponsive esx19 (exited maint): 87 minutes unresponsive esx24 (stayed in maint): 32 minutes unresponsive esx29 (stayed in maint): 39 minutes unresponsive esx32 (stayed in maint): 30 minutes unresponsive esx34 (exited maint): 70 minutes unresponsive Edit: The disconnect time idea seems to have been a red herring, as it's not happening consistently. Additionally, in the vpxd.log the exit maint mode task initiation seems to always immediately follow this vim.EnvironmentBrowser.queryProvisioningPolicy SOAP call. Here's the lines, slightly trimmed for clarity: 15:27:49.535 [info 'vpxdvpxdVmomi'] [ClientAdapterBase::InvokeOnSoap] Invoke done (esx31, vim.EnvironmentBrowser.queryProvisioningPolicy) 15:27:49.560 [info 'commonvpxLro'] [VpxLRO] -- BEGIN task -- esx31 -- HostSystem.exitMaintenanceMode -- Note that on the nodes that don't get the exit task, the vim.EnvironmentBrowser.queryProvisioningPolicy event still occurs. I'm not seeing any other differences in events before or after this in the reconnect process, aside from the extra events caused by exiting maintenance mode. Given the log's mention of provisioning policies, looking for autodeploy-related maintenance mode issues turns up complaints about similar behavior (though I'm not using autodeploy at all).

  Read the article

• DPM 2010 "Disk failed or disk not found"

  - by SysAdmin

  I have an HP Proliant ML110 G5 server with Windows server 2008R2 only dedicated for DPM 2010. This server has a limit in HD of 8TB which has already been met. I'm now stuck in this situation where my disk keeps failing "Disk failed or Disk not found" in the disk management. Only after I reboot the system the disk comes back up. Today I was running my monthly tape backup on a certain protection group and the disk failed again while the tape job was running (so the job wasn't completed). This is the description of the error in the alerts: "The disk Disk 1 - Hitachi HDS722020ALA330 SCSI Disk Device cannot be detected or has stopped responding. All subsequent protection activities that use this disk will fail until the disk is brought back online. (ID 3120)". My backup system is becoming useless! I don't think that is a hardware issue (please correct me if I'm wrong) since the HD works fine for a certain period of time which is becoming shorter and shorter. I basically have no more option to fix this problem. I tried to fix any error that was coming up in the event viewer with no luck (included one regarding the SQL2008 compatibility issue). The disk keeps failing! Now I'm only trying to recover/migrate the data from the disk that is having problem but my issue now is that I cannot add any drives to my server since I already got installed the maximum storage capacity 8TB. I thought about 2 simple options. Please tell me what you guys think about it; Unplug one of the 2 storage pool disks (disk0, that one without problem) from the machine and install a new one in order to migrate the data with the Migration tool for DPM. Remove the defective disk (disk1), put back the disk0 and run the synchronization/consistency check on all the groups to recreate replicas and recovery points. Run diskpart.exe and clean up the disk (loosing all data) and hoping that he will work after I sync all the protection groups. Both solutions are not elegant but I have no better options at the moment. Please I need some help. Thanks for your time Angelo

  Read the article

• Problem installing Cardbus/PCMCIA drivers (USB 2.0 2-port)

  - by Carl

  I obtained the drivers from the manufacturer for my HT-Link NEC USB 2.0 2-port Cardbus card. When I plugged in the card before I got the drivers, 3 new entries showed up in the Device Manager - two "NEC PCI to USB Open Host Controller" and one "Standard Enhanced PCI to USB Host controller." With the card plugged in, I uninstalled those two drivers. I then removed the card. I copied the new drivers to c:\windows\system32\drivers and the .inf file to c:\windows\inf. I also copied the drivers & inf to a new directory called c:\windows\drivers\ousb2. I reinserted the card. Windows automatically installed the same drivers as before. I selected 'update driver' on the "NEC PCI to USB..." entry and didn't see any other options. I then selected 'have disk' and pointed to c:\windows\drivers\ousb2 and got a message "The specified location does not contain information about your hardware." I then selected 'update driver' on the "Standard Enhanced PCI to USB...," and manually selected "USB 2.0 Enhanced Host Controller" (OWC 4/15/2003 2.1.3.1). Windows then automatically found a USB root hub, and I manually selected "USB 2.0 Root Hub Device" (OWC 4/15/2003 2.1.3.1). Now there are two sections in the Device Manager titled "Universal Serial Bus controllers." I plugged in my external USB hard disk adapter, and "USB Mass Storage Device" was added to the first set. Here's how it looks (w/drivers from the properties): [Universal Serial Bus controllers] Intel(R) 82801DB/DBM USB 2.0 Enhanced Host Controller - 24CD (6/1/2002 5.1.2600.0) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C2 (7/1/2001 5.1.2600.5512) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C4 (7/1/2001 5.1.2600.5512) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C7 (7/1/2001 5.1.2600.5512) NEC PCI to USB Open Host Controller (7/1/2001 5.1.2600.5512) NEC PCI to USB Open Host Controller (7/1/2001 5.1.2600.5512) USB Mass Storage Device USB Root Hub (7/1/2001 5.1.2600.5512) (5 more USB Root Hubs - same driver) [Universal Serial Bus controllers] USB 2.0 Enhanced Host Controller (OWC 4/15/2003 2.1.3.1) USB 2.0 Root Hub Device (OWC 4/15/2003 2.1.3.1) When I unplug the card the two "NEC PCI to USB..." entries in the first set disappear, and the whole second set disappears. (I unplugged the hard disk adapter first...) The hard disk adapter still doesn't work in that Cardbus card with the new drivers. I don't think the above looks right - a second set of USB controllers listed in the Device Manager, and the NEC entries still in the first set, and the the USB mass storage device still in the first set. Any help appreciated. (Windows XP PRO SP3 w/all current updates.)

  Read the article

• Issues getting a Cisco WLC 5508 to find AIR-LAP1142N

  - by user95917

  hoping someone can help me with a problem here. I'm attempting to setup a test (loan from Cisco) wireless network. Here's what i've got/done: 5508 Controller - Service Port IP set to 10.74.5.2 /24. Management IP set to 10.74.6.2 /24 with a default gateway of 10.74.6.1. Virtual IP set to 1.1.1.1. Copper SFP in slot 7, CAT5 (known good) going from there to port 1/0/47 on the switch. Green lights on both ends. 2960-S Switch - Vlan1 - 10.74.6.1 /24. dhcp pool 10.74.6.0 /24, default router 10.74.6.1. excluded-address 10.74.6.1, 10.74.6.2. 1/0/4 on the switch is set to switchport mode access and no shut. 1/0/47 on the switch is setup to switchport mode trunk and no shut. 1/0/4 has a CAT5 (known good) cable going from there to the AP. When I do a sh cdp nei from the switch, i can see the AP and Controller listed. When i configure my PC's nic to 10.74.5.5, and plug a cable from my nic to the SP port on the controller i can get on the device via the gui. In there, the only errors/info that show up in the trap are: Link Up: Slot: 0 Port: 7 Controller time base status - Controller is out of sync with the central timebase. I've manually set the time but apparently that's not quite the problem (or at least not the entire problem). When i plug the AP in, i see on the switch console that it grants it power, it sees it connect...but the controller won't see it for some reason. From what i've read you shouldn't have to do anything to the AP as it's managed by the controller...but i'm not sure what setting I'm missing for it to work. The AP light on top is continually cycling green, red, yellow. When I first start it up, it blinks green for 20 or so seconds, then goes to solid green for another 20 seconds or so, then flashes blue, green, red for awhile...but always ends up goinn back to the standard, green, red, yellow. Does anyone see any obvious issues with my setup or have any suggestions as to why i might be having a problem? Thanks for your help!

  Read the article

• Android emulator performance on linux

  - by Rado

  I installed the android SDK and eclipse plugin on my laptop, but I was surprised to find out that the emulator eats up 100% of one of my cpu cores. I have exactly the same setup on a desktop machine that does not have this issue. Both computers are running arch linux and both were updated yesterday. Granted, the desktop has better hardware than the laptop, but I was expecting to get closer to 50% cpu usage than 100% on the laptop. Both android virtual devices have the same specs: CPU: ARM Target: Android 2.3.3 - API Level 10 Skin: WVGA800 SD Card: 512M hw.lcd.density: 240 vm.heapSize: 24 hw.ramSize: 256 Laptop host has Intel Core 2 T7200 @ 2GHz cpu with 2Gb RAM. Desktop host has AMD Phenom II X4 940 @ 3GHz cpu with 8Gb RAM. The android emulator uses only 1 core and here are the CPU usage results: Laptop: Cpu0 : 22.8%us, 76.5%sy, 0.0%ni, 0.3%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st Cpu1 : 11.2%us, 2.4%sy, 0.0%ni, 86.4%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 2055484k total, 1860304k used, 195180k free, 5276k buffers Swap: 2000088k total, 106872k used, 1893216k free, 350780k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2026 xyz 20 0 396m 207m 7192 R 100 10.3 4:11.58 emulator-arm Desktop: Cpu0 : 0.7%us, 0.0%sy, 0.0%ni, 99.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 1.3%us, 0.0%sy, 0.0%ni, 98.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 5.0%us, 1.3%sy, 0.0%ni, 91.9%id, 1.7%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 0.3%us, 0.3%sy, 0.0%ni, 99.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 7666324k total, 6506808k used, 1159516k free, 1650960k buffers Swap: 8988348k total, 0k used, 8988348k free, 2867300k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2811 xyz 20 0 392m 220m 6276 S 8 2.9 0:33.58 emulator-arm Is there any way I can improve the emulator performance on the laptop? [UPDATE] I ran the emulator with the same settings, on the same laptop under Win7 and after starting up, it didn't use 100% of a CPU core unlike under linux. Also, I tried running the emulator from a terminal in Linux and I get this message when I don't get it under the desktop Linux host: Could not configure '/dev/hpet' to have a 1024Hz timer. This is not a fatal error, but for better emulation accuracy type: 'echo 1024 /proc/sys/dev/hpet/max-user-freq' as root. I'm not really familiar with rtc or hpet, but it doesn't seem that max-user-freq setting does anything, I still get the same warning.

  Read the article

• gunicorn + django + nginx unix://socket failed (11: Resource temporarily unavailable)

  - by user1068118

  Running very high volume traffic on these servers configured with django, gunicorn, supervisor and nginx. But a lot of times I tend to see 502 errors. So I checked the nginx logs to see what error and this is what is recorded: [error] 2388#0: *208027 connect() to unix:/tmp/gunicorn-ourapp.socket failed (11: Resource temporarily unavailable) while connecting to upstream Can anyone help debug what might be causing this to happen? This is our nginx configuration: sendfile on; tcp_nopush on; tcp_nodelay off; listen 80 default_server; server_name imp.ourapp.com; access_log /mnt/ebs/nginx-log/ourapp-access.log; error_log /mnt/ebs/nginx-log/ourapp-error.log; charset utf-8; keepalive_timeout 60; client_max_body_size 8m; gzip_types text/plain text/xml text/css application/javascript application/x-javascript application/json; location / { proxy_pass http://unix:/tmp/gunicorn-ourapp.socket; proxy_pass_request_headers on; proxy_read_timeout 600s; proxy_connect_timeout 600s; proxy_redirect http://localhost/ http://imp.ourapp.com/; #proxy_set_header Host $host; #proxy_set_header X-Real-IP $remote_addr; #proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; #proxy_set_header X-Forwarded-Proto $my_scheme; #proxy_set_header X-Forwarded-Ssl $my_ssl; } We have configure Django to run in Gunicorn as a generic WSGI application. Supervisord is used to launch the gunicorn workers: home/user/virtenv/bin/python2.7 /home/user/virtenv/bin/gunicorn --config /home/user/shared/etc/gunicorn.conf.py daggr.wsgi:application This is what the gunicorn.conf.py looks like: import multiprocessing bind = 'unix:/tmp/gunicorn-ourapp.socket' workers = multiprocessing.cpu_count() * 3 + 1 timeout = 600 graceful_timeout = 40 Does anyone know where I can start digging to see what might be causing the problem? This is what my ulimit -a output looks like on the server: core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 59481 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 50000 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) 1024 virtual memory (kbytes, -v) unlimited file locks (-x) unlimited

  Read the article

• order of operations for environment variables

  - by alyda

  I want to understand how environment variables are set and reset (overridden). I'm running Apache/2.2.24 (Unix) PHP/5.4.14 on a mac . My theory is this: Environment vars can be set in bash, then they can be overwritten with httpd.conf preceding a VirtualHost directive that precedes php.ini, which can then be overwritten by .htaccess (if allowable) and finally by PHP I tried the following: setting environment variable in bash: I added export ENVIRONMENT='local' to my ~/.bashrc file, restarted apache and did not get any output from print_r($_ENV); (in a simple index.php file at the root of my webserver). I also tried putting ENVIRONMENT='local' into /etc/environment, and restarting apache, nothing, as well as /etc/bashrc, restart apache. still nothing. setting environment variable in httpd.conf: I added SetEnv ENVIRONMENT 'local-httpd to the end of my /etc/apache2/httpd.conf file (but before I load other conf files, such as virtual host [Include /private/etc/apache2/other/*.conf]). I now see the variable in the array print_r($_SERVER); but not print_r($_ENV);. setting environment variable in httpd-vhosts.conf: I added SetEnv ENVIRONMENT 'local-vhost to my /etc/apache2/extra/httpd-vhosts.conf file in my generic directive that points to my default document root. I now see the variable has been overwritten (to local-vhost from local-httpd, so I know where the variable is getting set). setting environment variable in php.ini: while searching for a proper place to put my environment variable, I noticed that variables_order = "GPCS" was set to the production value rather than EGPCS. I changed it, restarted my server and found that I was now getting output for print_r($_ENV); but not my expected custom variable. It also appears that I am not able to set a custom variable in this file. Please tell me if I am wrong setting environment variable in .htaccess: I added SetEnv ENVIRONMENT 'local-htaccess'. This worked as expected, overwriting all other values that were set. setting / overwriting environment variable in PHP: if (...) { putenv('ENVIRONMENT=local'); } I'm asking this question because I have a lot of local and remote testing servers, some of which may or may not allow me access to modify httpd, httpd-vhost, php.ini or environment variables. I want to understand what is best for those difference scenarios (shared hosting, heroku, local servers, etc) I obviously don't know how to properly set the environment variable in bash in a way that php can use it, I'd like to know how to do that (as I think Heroku does something similar with heroku config set...)

  Read the article

• Can't manage iPod from linux anymore

  - by kemp

  I used to be able to see and manage my iPod with different softwares: Amarok, Rhythmbox, GTKPod. The device is a nano 1st generation 4gb. Currently it mounts regularly and can be accessed from the file system, but I get this in dmesg: [ 1547.617891] scsi 11:0:0:0: Direct-Access Apple iPod 1.62 PQ: 0 ANSI: 0 [ 1547.619103] sd 11:0:0:0: Attached scsi generic sg2 type 0 [ 1547.620478] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 [ 1547.620494] sd 11:0:0:0: [sdb] 7999487 512-byte hardware sectors: (4.09 GB/3.81 GiB) [ 1547.621718] sd 11:0:0:0: [sdb] Write Protect is off [ 1547.621726] sd 11:0:0:0: [sdb] Mode Sense: 68 00 00 08 [ 1547.621732] sd 11:0:0:0: [sdb] Assuming drive cache: write through [ 1547.623591] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 [ 1547.624993] sd 11:0:0:0: [sdb] Assuming drive cache: write through [ 1547.625003] sdb: sdb1 sdb2 [ 1547.629686] sd 11:0:0:0: [sdb] Attached SCSI removable disk [ 1548.084026] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.369502] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.504358] FAT: invalid media value (0x2f) [ 1548.504363] VFS: Can't find a valid FAT filesystem on dev sdb1. [ 1548.945173] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.945179] FAT: invalid media value (0x2f) [ 1548.945182] VFS: Can't find a valid FAT filesystem on dev sdb1. [ 1610.092886] usb 2-6: USB disconnect, address 9 The only application that can access it (partially) is Rhythmbox. I say partially because I can transfer files to the iPod but can't remove or modify them. Also one transfer didn't finish and only 9 out of 16 songs were delivered to the device. All other softwares I tried (GTKPod, Amarok, Songbird) don't even detect it. What can I do to troubleshoot this? EDIT: # fdisk -l /dev/sdb Disk /dev/sdb: 4095 MB, 4095737344 bytes 241 heads, 62 sectors/track, 535 cylinders Units = cylinders of 14942 * 512 = 7650304 bytes Disk identifier: 0x20202020 Device Boot Start End Blocks Id System /dev/sdb1 1 11 80293+ 0 Empty Partition 1 has different physical/logical beginnings (non-Linux?): phys=(0, 1, 1) logical=(0, 1, 2) Partition 1 has different physical/logical endings: phys=(9, 254, 63) logical=(10, 181, 8) Partition 1 does not end on cylinder boundary. /dev/sdb2 11 536 3919415+ b W95 FAT32 Partition 2 has different physical/logical beginnings (non-Linux?): phys=(10, 0, 7) logical=(10, 181, 15) Partition 2 has different physical/logical endings: phys=(497, 240, 62) logical=(535, 88, 61) EDIT2: The "before" state is hard to tell, it was a lot of updates ago. Haven't been using my iPod for a while so I can't say when exactly it stopped working. I'm sure Amarok was still at version 1.X but can't remember when it was. My current system is debian testing fully updated. NOTE: just noticed that if I mount the device manually instead of letting nautilus automount it, I can see it again on GTKPod but still not on Banshee AND it's vanished from Rhythmbox...

  Read the article

• Windows Server 2008 - one MAC Address, assign multiple external IP's to VirtualBoxes running as guests on host

  - by Sise

  Couldn't find any help @ google or here. The scenario: Windows Server 2008 Std x64 on i7-975, 12 GB RAM. The server is running in a data centre. One hardware NIC - RealTek PCIe GBE - one MAC Address. The data centre provides us 4 static external IP's. The first is assigned to the host by default of course. I have ordered all 4 IP's, the data centre can assign the available IP's to the physical MAC address of the given NIC only. This means one NIC, one MAC Address, 4 IP's. Everything works fine so far. Now, what I would like to have: Installed VirtualBox with 1-3 guests running, each gets it's own external IP assigned. Each of it should be an standalone Win Server 2008. It looks like the easiest way would be to put the guests into an virtual subnet and routing all data coming to the 2nd till 4th external IP through to this guests using there subnet IP's. I have been through the VirtualBox User Manuel regarding networking. What's not working: I can't use bridged networking without anything else, because the IP's are assigned to the one MAC address only. I can't use NAT networking because it does not allow access from outside or the host to the guest. I do not wanna use port forwarding. Host-only networking itself would not allow internet access, by sharing the default internet connection of the host, internet is granted from the guest to the outside but not from outside or the host to the guest. InternalNetworking is not really an option here. What I have tried is to create an additional MS Loopback adapter for a routed subnet, where the Vbox guests are in, now the idea was to NAT the internet connection to the loopback 'subnet'. But I can't ping the gateway from the guests. By using route command in the command shell or RRAS (static route, NAT) I didn't get there as well. Solutions like the following do work for the one way, but not for the way back: For your situation, it might be best to use the Host-Only adapter for ICS. Go to the preferences of VB itself and select network. There you can change the configuration for the interface. Set the IP address to 192.168.0.1, netmask 255.255.255.0. Disable the DHCP server if it isn't already and that's it. Now the Guest should get an IP from Windows itself and be able to get onto the internet, while you can also access the Host. Slowly I'm pretty stucked with this topic. There is a possibility I've just overlooked something or just didn't getting it by trying, especially using RRAS, but it's kinda hard to find useful howto's or something in the web. Thanks in advance! Best regards, Simon

  Read the article

• radvd is not assigning prefix

  - by Samik

  I'm currently trying to setup IPv6 address auto-configuration with router advertisement daemon (radvd) on a virtual machine running CentOS 6.5. But the eth0 interface is not obtaining that prefix. I've obtained the ULA prefix from here. Contents of /etc/sysctl.conf # Kernel sysctl configuration file for Red Hat Linux # # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and # sysctl.conf(5) for more details. # Controls IP packet forwarding net.ipv4.ip_forward = 0 net.ipv6.conf.all.forwarding = 1 # Controls source route verification net.ipv4.conf.default.rp_filter = 1 # Do not accept source routing net.ipv4.conf.default.accept_source_route = 0 # Controls the System Request debugging functionality of the kernel kernel.sysrq = 0 # Controls whether core dumps will append the PID to the core filename. # Useful for debugging multi-threaded applications. kernel.core_uses_pid = 1 # Controls the use of TCP syncookies net.ipv4.tcp_syncookies = 1 # Disable netfilter on bridges. net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 # Controls the default maxmimum size of a mesage queue kernel.msgmnb = 65536 # Controls the maximum size of a message, in bytes kernel.msgmax = 65536 # Controls the maximum shared segment size, in bytes kernel.shmmax = 68719476736 # Controls the maximum number of shared memory segments, in pages kernel.shmall = 4294967296 Contents of /etc/radvd.conf # NOTE: there is no such thing as a working "by-default" configuration file. # At least the prefix needs to be specified. Please consult the radvd.conf(5) # man page and/or /usr/share/doc/radvd-*/radvd.conf.example for help. # # interface eth0 { AdvSendAdvert on; MinRtrAdvInterval 3; MaxRtrAdvInterval 10; AdvDefaultPreference low; AdvHomeAgentFlag off; prefix fd8a:8d9d:808f:1::/64 { AdvOnLink on; AdvAutonomous on; AdvRouterAddr on; }; }; Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes I've also enabled radvd at startup through chkconfig. Though I noticed that radvd is starting after interfaces are brought up. I've tried restarting the network service afterwards but still I get the following link-local address only #ip -6 addr show 1: lo: mtu 16436 inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qlen 1000 inet6 fe80::5054:ff:fe74:d746/64 scope link valid_lft forever preferred_lft forever Edit: Based on the answer given by Sander Steffann I still need clarification on some points but I'm posting here what worked. Contents of /etc/sysconfig/network NETWORKING=yes HOSTNAME=syslog-ng-server NETWORKING_IPV6=yes IPV6FORWARDING=yes Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes IPV6FORWARDING=no Removed following line from /etc/sysctl.conf net.ipv6.conf.all.forwarding = 1 Contents of /etc/radvd.conf is as previous.

  Read the article

• Django + gunicorn + virtualenv + Supervisord issue

  - by Florian Le Goff

  Dear all, I have a strange issue with my virtualenv + gunicorn setup, only when gunicorn is launched via supervisord. I do realize that it may very well be an issue with my supervisord and I would appreciate any feedback on a better place to ask for help... In a nutshell : when I run gunicorn from my user shell, inside my virtualenv, everything is working flawlessly. I'm able to access all the views of my Django project. When gunicorn is launched by supervisord at the system startup, everything is OK. But, if I have to kill the gunicorn_django processes, or if I perform a supervisord restart, once that gunicorn_django has relaunched, every request is answered with a weird Traceback : (...) File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/__init__.py", line 77, in connection = connections[DEFAULT_DB_ALIAS] File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/utils.py", line 92, in __getitem__ backend = load_backend(db['ENGINE']) File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/utils.py", line 50, in load_backend raise ImproperlyConfigured(error_msg) TemplateSyntaxError: Caught ImproperlyConfigured while rendering: 'django.db.backends.postgresql_psycopg2' isn't an available database backend. Try using django.db.backends.XXX, where XXX is one of: 'dummy', 'mysql', 'oracle', 'postgresql', 'postgresql_psycopg2', 'sqlite3' Error was: cannot import name utils Full stack available here : http://pastebin.com/BJ5tNQ2N I'm running... Ubuntu/maverick (up-to-date) Python = 2.6.6 virtualenv = 1.5.1 gunicorn = 0.12.0 Django = 1.2.5 psycopg2 = '2.4-beta2 (dt dec pq3 ext)' gunicorn configuration : backlog = 2048 bind = "127.0.0.1:8000" pidfile = "/tmp/gunicorn-hc.pid" daemon = True debug = True workers = 3 logfile = "/home/hc/prod/log/gunicorn.log" loglevel = "info" supervisord configuration : [program:gunicorn] directory=/home/hc/prod/hc command=/home/hc/prod/venv/bin/gunicorn_django -c /home/hc/prod/hc/gunicorn.conf.py user=hc umask=022 autostart=True autorestart=True redirect_stderr=True Any advice ? I've been stuck on this one for quite a while. It seems like some weird memory limit, as I'm not enforcing anything special : $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 20 file size (blocks, -f) unlimited pending signals (-i) 16382 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) unlimited virtual memory (kbytes, -v) unlimited file locks (-x) unlimited Thank you.

  Read the article

• Windows Vista: Networking can only connect "local only"

  - by Damien

  I am attempting to debug a problem on a Windows Vista laptop - not mine! Until just recently (last week or so), it was operating normally for about 4 years :) The problem is that I am having issues connecting to the local network (a basic wireless home router; more later) and the internet (via ADSL). This is both for wired [Broadcom chipset] and wireless [Intel chipset]. I will elaborate further later. To detail the network. I have three other clients (HTC phone, Ubuntu 12.04 desktop [wired] and Ubuntu 10.04 laptop [wireless]), all of whom are able to connect to the network and internet normally. A windows 7 virtual machine running on said desktop connects normally. I have tried two different wireless routers - Netgear DG834G and Netgear DGN3500. The same error mode is common to both. Updating the firmware to the latest on both routers does not help. Overall, it seems safe to say it's localised to the laptop in question. I do not have another Vista client to test with. The specific symptoms are as follows: When "connected", it says "Local Only", and says it cannot connect to the internet. This is true for both wired and wireless. It can get an IP address (192.168.0.5), and the router (192.168.0.1) reports that it can see the device. When I try to ping, I get the following results: ping 192.168.0.1 - (router) all packets lost ping 192.168.0.5 - (laptop's address) OK ping 192.168.0.4 - (desktop) all packets lost Pinging from the desktop to the problematic laptop results in "From 192.168.0.4 icmp_seq=1 Destination Host Unreachable" The most promising "fix" from trawling forums is KB928233 which does not work for me. The problem is persistent across reports (both full shutdown and hibernate) so it appears not to be sleep related. I am not a regular vista user, though I can fumble my way about a bit. Is there any other suggestions as to what I should do? Is there any further information I can provide?

  Read the article

• Why do I need to set up Autologon values in registry twice in before it works and can I fix this?

  - by jJack

  Background: As part an automated testing suite I am building, I need to set up Autologon on my virtual machines 'on demand'. By on demand, I mean that I don't want to necessarily pre-configure my VM or any snapshot to have Autologon set up already, for security reasons and also a huge business case. My solution so far: I'm copying a script to the guest machine and then using Sysinternals PsExec to execute it. The script is: reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v DefaultUserName /t REG_SZ /d myusername reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v DefaultPassword /t REG_SZ /d myfakepassword reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v DefaultDomainName /t REG_SZ /d mydomain reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v ForceAutoLogon /t REG_SZ /d 1 reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v AutoAdminLogon /t REG_SZ /d 1 reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon\AutoLogonChecked" /f /ve /d 1 Note: I don't believe AutoLogonChecked is required for machines post Windows 2000 but I'm doing it just in case for now. Maybe ForceAutoLogon isn't either, not sure yet. The Problem: I see PsExec executes this properly and all the values are in the registry, however when I restart the machine, the user isn't automatically logged on...When I run this a second time then restart the machine, the user is finally logged on. A diff between the registry states shows that the first time I run this, it is missing both the "1" for AutoAdminLogon, and also the DefaultPassword key. The second time I execute it, these values are correctly intact as I intended. So, what is going on here? Is this expected? This post claims in the end that it really all just works (the problem was that a logoff script was setting off the values). Doesn't seem to work for me however. Note this seems unique to Windows 7, does not occur in Windows XP Also note that you don't need PsExec to recreate the issue - just modify the registry yourself EDIT/update: Login interactively and run script (so, not executing it remotely), logging off automatically logs me back in (so, it works) remotely execute the script in guest when I'm interactively logged in, logging off automatically logs me back in (so, it works) remotely execute the script in guest when with non-interactive session if I log in afterwards (so, interactive now) then back off, it logs me back in (so, it then works) EDIT/update 2: This only occurs for Win7x86, Win7x64, Win8x64. This does not occur for Windows XP

  Read the article

• Netdom to restore machine secret

  - by icelava

  I have a number of virtual machines that have not been switched on for over a month, and some others which have been rolled back to an older state. They are members of a domain, and have expired their machine secrets; thus unable to authenticate with the domain any longer. Event Type: Warning Event Source: LSASRV Event Category: SPNEGO (Negotiator) Event ID: 40960 Date: 14/05/2009 Time: 10:24:54 AM User: N/A Computer: TFS2008WDATA Description: The Security System detected an authentication error for the server ldap/iceland.icelava.home. The failure code from authentication protocol Kerberos was "The attempted logon is invalid. This is either due to a bad username or authentication information. (0xc000006d)". For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: c000006d Event Type: Warning Event Source: LSASRV Event Category: SPNEGO (Negotiator) Event ID: 40960 Date: 14/05/2009 Time: 10:24:54 AM User: N/A Computer: TFS2008WDATA Description: The Security System detected an authentication error for the server cifs/iceland.icelava.home. The failure code from authentication protocol Kerberos was "The attempted logon is invalid. This is either due to a bad username or authentication information. (0xc000006d)". For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: c000006d Event Type: Error Event Source: NETLOGON Event Category: None Event ID: 3210 Date: 14/05/2009 Time: 10:24:54 AM User: N/A Computer: TFS2008WDATA Description: This computer could not authenticate with \\iceland.icelava.home, a Windows domain controller for domain ICELAVA, and therefore this computer might deny logon requests. This inability to authenticate might be caused by another computer on the same network using the same name or the password for this computer account is not recognized. If this message appears again, contact your system administrator. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: c0000022 So I try to use netdom to re-register the machine back to the domain C:\Documents and Settings\Administrator>netdom reset tfs2008wdata /domain:icelava /UserO:enterpriseadmin /PasswordO:mypassword Logon Failure: The target account name is incorrect. The command failed to complete successfully. But have not been successful. I wonder what else needs to be done?

  Read the article

• backup of KVM VM's running on Ubuntu 12.4.1 precise edition from a remote machine

  - by Dr. Death

  I am creating a library API which will take the backup of all the VM's running on KVM hypervisor. My VM's can be of any type. I am taking this backup from a remote machine and need to put the backup at remote server. I have KVM, Libvirt installed on my system. Some of my VM's are LVM based and some are normal VM's running on KVM. I research and found out an excellent perl script for taking the backup http://pof.eslack.org/2010/12/23/best-solution-to-fully-backup-kvm-virtual-machines/ but since I am developing this library in C++ I cannot use it however it has given me a good understanding of how it will work. One thing I didnot able to sort out is if my VM's are not created using virt-manager or are created using any other tool them virsh system list command does not give them in the list of running VM's however they are running perfectly on my KVM server. Is there a way to list these VM's in my system list anyhow? secondly, when I am taking backup from the remote machine I am getting out of my ssh mode as soon as my libvirt command finishes and for every command I need to ssh again, Is there a way that I do not need to ssh each and every time? I have already used the rsa key for ssh but when once my command finishes my control moves to the remote machine again and try to find out my source VM location in remote machine's local drives which in turn fails it. here is the main problem I am facing. also for the LVM based VM I am able to take the live backup but for non LVM based my machines are getting suspended and not been able to take the live backup. Since my library will work on the remote machine only I might not know the VM's configruation on the KVM server. so need to make it consistent for all the VM's. Please share any thing related to this issue so that I may be able to take the live backup of the non lvm vm's also. I'll update my working and any research findings time to time to all of you. Thanks in advance for your suggestions in these regards.

  Read the article

• external hard drive is no longer recognized, gives buffer I/O errors

  - by BioGeek

  Hi all, The external hard drive which contains all my photos and where I backed-up all my important documents is no longer recognized. It is a three month old 500GB Iomage Prestige Desktop Hard Drive. When I plug it in, it is recognised as a USB device, because it shows up when I type lsusb, but dmesg gives this error message. [19712.013250] usb 2-2: new high speed USB device using ehci_hcd and address 21 [19712.145347] usb 2-2: configuration #1 chosen from 1 choice [19712.147214] scsi25 : SCSI emulation for USB Mass Storage devices [19712.147514] usb-storage: device found at 21 [19712.147519] usb-storage: waiting for device to settle before scanning [19717.148978] usb-storage: device scan complete [19717.149527] scsi 25:0:0:0: Direct-Access ST350082 0AS PQ: 0 ANSI: 2 CCS [19717.151020] sd 25:0:0:0: Attached scsi generic sg2 type 0 [19717.151685] sd 25:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) [19717.160402] sd 25:0:0:0: [sdb] Write Protect is off [19717.160412] sd 25:0:0:0: [sdb] Mode Sense: 34 00 00 00 [19717.160418] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165685] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165691] sdb: sdb1 [19719.171808] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19719.171818] sd 25:0:0:0: [sdb] Attached SCSI disk [19737.430998] sd 25:0:0:0: [sdb] Unhandled sense code [19737.431007] sd 25:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [19737.431016] sd 25:0:0:0: [sdb] Sense Key : Medium Error [current] [19737.431027] sd 25:0:0:0: [sdb] Add. Sense: Unrecovered read error [19737.431038] end_request: I/O error, dev sdb, sector 6160463 [19737.431050] Buffer I/O error on device sdb1, logical block 6160400 [19737.431060] Buffer I/O error on device sdb1, logical block 6160401 [19737.431067] Buffer I/O error on device sdb1, logical block 6160402 [19737.431075] Buffer I/O error on device sdb1, logical block 6160403 [19737.431082] Buffer I/O error on device sdb1, logical block 6160404 [19737.431088] Buffer I/O error on device sdb1, logical block 6160405 [19737.431096] Buffer I/O error on device sdb1, logical block 6160406 [19737.431102] Buffer I/O error on device sdb1, logical block 6160407 [19737.431114] Buffer I/O error on device sdb1, logical block 6160408 [19737.431121] Buffer I/O error on device sdb1, logical block 6160409 [19737.712183] sd 6:0:0:0: [sdb] Unhandled sense code [19737.712191] sd 6:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE [19737.712200] sd 6:0:0:0: [sdb] Sense Key : Hardware Error [current] [19737.712210] sd 6:0:0:0: [sdb] Add. Sense: No additional sense information [19737.712222] end_request: I/O error, dev sdb, sector 0 [19737.712232] Buffer I/O error on device sdb, logical block 0 Neither does the external drive show when I use fdisk: jeroen@phalacrocorax:~$ sudo fdisk -l [sudo] password for jeroen: Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000341ad Device Boot Start End Blocks Id System /dev/sda1 * 1 18714 150320173+ 83 Linux /dev/sda2 18715 19457 5968147+ 5 Extended /dev/sda5 18715 19457 5968116 82 Linux swap / Solaris` I popped the disk out of the casing put it on a SATA connect internally and then tried the file recovery programs testdisk/photorec and SpinRite, but both failed because they couldn't recognize the external harddisk. Do I have any other options?

  Read the article

• Why do Ping and Dig provide different IP address than nslookup?

  - by user1032531

  When pinging my domain name which points to my home public IP from two different servers on my LAN, it shows them pinging different IP. Further investigation shows dig and nslookup providing different results. See below. A little history. My IP used to be 11.22.33.444 and is hosted by Comcast. I changed routers, and it somehow got changed to 55.66.77.888. I've since updated my 1and1 domain name to point to the 55.66.77.888. desktop is a basic server, runs the web server, and connects wirelessly to my LAN. laptop is a GUI and connected via CAT5. Both operate Centos6.4. My old router was a D-Link, and used their "Virtual Server" feature to pass port 80 to desktop. My new router is a Linksys, and I use their "Port Forwarding" feature to pass port 80 to desktop (however, I haven't gotten this part working yet). What is going on??? Why the different IPs? Obviously, it most somehow be stored on the server, but why does the actual machine even know the public IP since it is on a LAN? How do I purge the old IP? [root@desktop etc]# dig +short myDomain.com 11.22.33.444 [root@desktop etc]# nslookup www.myDomain.com Server: 8.8.8.8 Address: 8.8.8.8#53 Non-authoritative answer: Name: www.myDomain.com Address: 55.66.77.888 [root@desktop etc]# dig myDomain.com ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.17.rc1.el6_4.6 <<>> myDomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 13822 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;myDomain.com. IN A ;; ANSWER SECTION: myDomain.com. 16031 IN A 11.22.33.444 ;; Query time: 21 msec ;; SERVER: 8.8.8.8#53(8.8.8.8) ;; WHEN: Mon Oct 21 04:36:52 2013 ;; MSG SIZE rcvd: 44 [root@desktop etc]# [root@laptop ~]# dig +short myDomain.com 55.66.77.888 [root@laptop ~]# nslookup www.myDomain.com Server: 192.168.0.1 Address: 192.168.0.1#53 Non-authoritative answer: Name: www.myDomain.com Address: 55.66.77.888 [root@laptop ~]#

  Read the article

• ubuntu mail server settings and /etc/hosts file

  - by mbrc

  This is my /etc/hosts file 127.0.0.1 localhost.localdomain localhost 127.0.1.1 ubuntu-server.xx.com ubuntu-server 193.77.xx.xx mail.xx.com mail # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters is this correct configuration for my mail server. I am behind router so i don't know if is ok to use my IP for mail.xx.com and 127.0.0.1 for localhost problem is that i can receive mail but when i send it i get Oct 17 21:29:32 ubuntu-server postfix/smtpd[2453]: warning: SASL authentication failure: Password verification failed Oct 17 21:29:32 ubuntu-server postfix/smtpd[2453]: warning: my.router[192.168.1.1]: SASL PLAIN authentication failed: authentication failure Oct 17 21:29:34 ubuntu-server postfix/smtpd[2453]: warning: my.router[192.168.1.1]: SASL LOGIN authentication failed: authentication failure EDIT: mabye is problem some port. i foward this ports. POP3 - port 110 IMAP - port 143 SMTP - port 25 HTTP - port 80 Secure SMTP (SSMTP) - port 465 Secure IMAP (IMAP4-SSL) - port 585 StartTLS - port 587 IMAP4 over SSL (IMAPS) - port 993 Secure POP3 (SSL-POP) - port 995 postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix content_filter = amavis:[127.0.0.1]:10024 delay_warning_time = 4h disable_vrfy_command = yes inet_interfaces = all inet_protocols = all mailbox_size_limit = 0 maximal_backoff_time = 8000s maximal_queue_lifetime = 7d message_size_limit = 0 minimal_backoff_time = 1000s mydestination = myhostname = mail.xx.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mynetworks_style = host myorigin = /etc/mailname readme_directory = no receive_override_options = no_address_mappings recipient_delimiter = + relayhost = smtp_helo_timeout = 60s smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name smtpd_client_restrictions = reject_rbl_client sbl.spamhaus.org, reject_rbl_client blackholes.easynet.nl, reject_rbl_client dnsbl.njabl.org smtpd_data_restrictions = reject_unauth_pipelining smtpd_delay_reject = yes smtpd_hard_error_limit = 12 smtpd_helo_required = yes smtpd_helo_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_hostname, reject_invalid_hostname, permit smtpd_recipient_limit = 16 smtpd_recipient_restrictions = reject_unauth_pipelining, permit_mynetworks, permit_sasl_authenticated, reject_non_fqdn_recipient, reject_unknown_recipient_domain, reject_unauth_destination, permit smtpd_sasl_auth_enable = yes smtpd_sasl_local_domain = smtpd_sasl_security_options = noanonymous smtpd_sender_restrictions = permit_sasl_authenticated, permit_mynetworks, warn_if_reject reject_non_fqdn_sender, reject_unknown_sender_domain, reject_unauth_pipelining, permit smtpd_soft_error_limit = 3 smtpd_tls_cert_file = /etc/ssl/private/mail.xx.com.crt smtpd_tls_key_file = /etc/ssl/private/mail.xx.com.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes unknown_local_recipient_reject_code = 450 virtual_alias_maps = mysql:/etc/postfix/maps/alias.cf virtual_gid_maps = static:5000 virtual_mailbox_base = /var/spool/mail/virtual virtual_mailbox_domains = mysql:/etc/postfix/maps/domain.cf virtual_mailbox_limit = 0 virtual_mailbox_maps = mysql:/etc/postfix/maps/user.cf virtual_uid_maps = static:5000 saslfinger -c version: 1.0.4ostfix Cyrus sasl configuration Ä mode: client-side SMTP AUTH -- basics -- Postfix: 2.9.3 System: Ubuntu 12.04.1 LTS \n \l -- smtp is linked to -- libsasl2.so.2 => /usr/lib/i386-linux-gnu/libsasl2.so.2 (0x00d3a000) -- active SMTP AUTH and TLS parameters for smtp -- relayhost = smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes -- listing of /usr/lib/sasl2 -- total 28 drwxr-xr-x 2 root root 4096 okt 14 15:18 . drwxr-xr-x 72 root root 12288 okt 14 15:03 .. -rw-r--r-- 1 root root 1 maj 4 06:17 berkeley_db.txt -rw-r----- 1 root root 701 okt 14 15:18 saslpasswd.conf -rw-r----- 1 smmta smmsp 885 okt 14 15:18 Sendmail.conf -- listing of /etc/postfix/sasl -- total 12 drwxr-xr-x 2 root root 4096 okt 11 18:55 . drwxr-xr-x 4 root root 4096 okt 12 06:59 .. -rwx------ 1 root root 241 okt 11 18:55 smtpd.conf Cannot find the smtp_sasl_password_maps parameter in main.cf. Client-side SMTP AUTH cannot work without this parameter!

  Read the article

• SQL Server High Availability - Mirroring with MSCS?

  - by David

  I'm looking at options for high-availability for my SQL Server-powered application. The requirements are: HA protection from storage failure. Data accessibility when one of the DB servers is undergoing software updates (e.g. planned outage for Windows Update / SQL Server service-packs). Must not involve much in the way of hardware procurement. The application is an ASP.NET web application. The web application's users have their own database instances. I've seen two main options: SQL Server failover clustering, and SQL Server mirroring. I understand that SQL Server Failover Clustering requires the purchasing of a shared disk array and doesn't offer any protection if the shared storage goes down (so the documentation recommends to set up a Mirroring between two clusters). Database Mirroring seems the cheaper option (as it only requires two database servers and a simple witness box) - but I've heard it doesn't work well when you have a large number of databases. The application I'm developing involves giving each client their own database for their application - there could be hundreds of databases. Setting up the mirroring is no problem thanks to the automation systems we have in place. My final point concerns how failover works with respect to client connections - SQL Server Failover Clustering uses MSCS which means that the cluster is invisible to clients - a connection attempt might fail during the failover, but a simple reconnect will have it working again. However mirroring, as far as I know, requires that the client be aware of the mirrored partners: if the client cannot connect to the primary server then it tries the secondary server. I'm wondering how this work with respect to Connection Pooling in ASP.NET applications - does the client connection failovering mean that there's a potential 2-second (assuming 2000ms TCP timeout policy) pause when the connection pool tries the primary server on every connection attempt? I read somewhere that Mirroring can be used on top of MSCS which means that the client does not need to be aware of mirroring (so there wouldn't be any potential delays during connection, and also that no changes would need to be made to the client, not even the connection string) - however I'm finding it hard to get documentation or white papers on this approach. But if true, then it means the best method is then Mirroring (for HA) with MSCS (for client ignorance and connection performance). ...but how does this scale to a server instance that might contain hundreds of mirrored databases?

  Read the article

• my multi boot can't boot to XP 'resumeobject' is missing

  - by GwenKillerby

  In my multi boot set up, booting to vista and 7 goes fine, but when I try to boot to XP, i get an error Windows failed to start. A recent hardware or software change might be the cause. To fix the problem: 1. Insert your Windows installation disc and restart your computer. 2. Choose your language settings, and then click "Next." 3. Click "Repair your computer." If you do not have this disc, contact your system administrator or computer manufacturer for assistance. File: \NTLDR Status: 0xc000000e Info: The selected entry could not be loaded because the application is missing or corrupt. See below. Clearly the resumeobject seems to be missing in the XP entry ("Real Mode Boot sector"), only I don't know how to restore it. Vista is on **C:**, Win7 is on **F:** (as is the bootmgr ??? ) and WinXP is on **E:** What I've tried: [1] I've used about 5 windows discs, that is the Recovery Consoles from real XP install CD's and 3 virtual Recovery Consoles. All failed. The real CD's work ONE time, but won't let me finish, I only got as far as [b]fixboot E:[/b] Then they shut the laptop down, I kid you not. On a next startup, all 5 CD's ask me for some Admin password that I've never added! [2] I have VisualBCD and EasyBCD, but the most obvious things I tried there didn't solve the problem. So know I don't exactly know what to do with them. [3] I CAN boot into XP with the FIX NTLDR workaround of http://milescomer.com/tinyempire.com/notes/ntldrismissing.htm, but it doesn't fix it permanently QUESTION: How do I fix it permanently? bcdedit /enum output: Windows Boot Manager -------------------- identifier {bootmgr} device partition=F: path \bootmgr description Windows Boot Manager locale en-US default {current} displayorder {current} {812e27a9-27b7-11e4-8fb4-dfa8174ae8dc} {812e27ac-27b7-11e4-8fb4-dfa8174ae8dc} timeout 30 resume No Windows Boot Loader ------------------- identifier {current} device partition=C: path \Windows\system32\winload.exe description Vista locale nl-NL osdevice partition=C: systemroot \Windows resumeobject {73d8b5bc-2764-11e4-b181-806e6f6e6963} Windows Boot Loader ------------------- identifier {812e27a9-27b7-11e4-8fb4-dfa8174ae8dc} device partition=F: path \Windows\system32\winload.exe description Daisy Etta locale en-US osdevice partition=F: systemroot \Windows resumeobject {b8c234a4-27b0-11e4-b8b3-806e6f6e6963} Real-mode Boot Sector --------------------- identifier {812e27ac-27b7-11e4-8fb4-dfa8174ae8dc} device partition=E: path \NTLDR description XP Thank you.

  Read the article

• .htaccess working on remote server but does not work on localhost. Getting 404 errors on localhost

  - by Afsheen Khosravian

  MY PROBLEM: When I visit localhost the site does not work. It shows some text from the site but it seems the server can not locate any other files. Here is a snippet of the errors from firebug: "NetworkError: 404 Not Found - localhost/css/popup.css" "NetworkError: 404 Not Found - localhost/css/style.css" "NetworkError: 404 Not Found - localhost/css/player.css" "NetworkError: 404 Not Found - localhost/css/ui-lightness/jquery-ui-1.8.11.custom.css" "NetworkError: 404 Not Found - localhost/js/jquery.js" It seems my server is looking for the files in the wrong places. For example, localhost/css/popup.css is actually located at localhost/app/webroot/css/popup.css. I have my site setup on a remote server with the same exact configurations and it works perfectly fine. I am just having this issue trying to run the site on my laptop at localhost. I edited my VirtualHosts file DocumentRoot and to /home/user/public_html/site.com/public/app/webroot/ and this reduces some errors but I feel that this is wrong and sort of hacking it since I didn't use these setting on my production server which works. The last note I want to make is that the website uses dynamic URLs. I dont know if that has anything to do with it. For example, on the production server the URLS are: site.com/#hello/12321. HERES WHAT I AM WORKING WITH: I have a LAMP server setup on my laptop which runs on Ubuntu 11.10. I have enabled mod_rewrite: sudo a2enmod rewrite Then I edited my Virtual Hosts file: <VirtualHost *:80> ServerName localhost DirectoryIndex index.php DocumentRoot /home/user/public_html/site.com/public <Directory /home/user/public_html/site.com/public/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> </VirtualHost> Then I restarted apache. My website is using cakePHP. This is the directory structure of the website: "/home/user/public_html/site.com/public" contains: index.php app cake plugins vendors These are my .htaccess files: /home/user/public_html/site.com/public/app/.htaccess: <IfModule mod_rewrite.c> RewriteEngine on RewriteRule ^$ webroot/ [L] RewriteRule (.*) webroot/$1 [L] </IfModule> /home/user/public_html/site.com/public/app/webroot/.htaccess: <IfModule mod_rewrite.c> RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_FILENAME} !-f RewriteRule ^(.*)$ index.php?url=$1 [QSA,L] </IfModule>

  Read the article

• Why is my cron daemon is being killed every few minutes? OpenVZ?

  - by user113215

  As of about a week ago, my cron daemon refuses to stay running. I'm using Debian 6. Running something like pgrep cron shows that the daemon isn't running. I start the service with service cron start or /etc/init.d/cron start and it launches, but it disappears from the running process list after a few minutes (varying anywhere between 1 - 30 minutes before the process is killed again). Using strace -f service cron start, I can see that the process is being killed for some reason: nanosleep({56, 0}, 0x7fffa7184c80) = 0 stat("crontabs", {st_mode=S_IFDIR|S_ISVTX|0730, st_size=4096, ...}) = 0 stat("/etc/crontab", {st_mode=S_IFREG|0644, st_size=1100, ...}) = 0 stat("/etc/cron.d", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 stat("/etc/cron.d/php5", {st_mode=S_IFREG|0644, st_size=475, ...}) = 0 stat("/etc/cron.d/anacron", {st_mode=S_IFREG|0644, st_size=244, ...}) = 0 rt_sigprocmask(SIG_BLOCK, [CHLD], [], 8) = 0 rt_sigaction(SIGCHLD, NULL, {0x4036f0, [CHLD], SA_RESTORER|SA_RESTART, 0x2b0e8465f230}, 8) = 0 rt_sigprocmask(SIG_SETMASK, [], NULL, 8) = 0 nanosleep({60, 0}, <unfinished ...> +++ killed by SIGKILL +++ There's nothing relevant in /var/log/syslog, /var/log/messages, /var/log/auth.log, or /var/log/kern.log to explain why the the process is dying. The system has about 500 MB of free memory, and cat /proc/loadavg returns 0.10 0.21 0.45 so resources shouldn't be the issue. I also tried removing and reinstalling the cron package using apt-get. What else should I check? How do I find out what's killing my crond? Edit: I'm on a virtual machine under OpenVZ (and as such, I have no swap). With cron running, free -m reports: total used free shared buffers cached Mem: 1024 465 558 0 0 0 -/+ buffers/cache: 465 558 Swap: 0 0 0 My OpenVZ User Beancounters via cat /proc/user_beancounters: Version: 2.5 uid resource held maxheld barrier limit failcnt 172087: kmemsize 8275718 25561636 51200000 51200000 0 lockedpages 0 968 2048 2048 0 privvmpages 113442 266465 262200 262200 3740757 shmpages 788 4004 128000 128000 0 dummy 0 0 0 0 0 numproc 39 98 600 600 0 physpages 50521 208434 0 9223372036854775807 0 vmguarpages 0 0 512000 512000 0 oomguarpages 50521 208447 512000 512000 0 numtcpsock 7 323 4096 4096 0 numflock 7 64 2048 2048 0 numpty 1 4 32 32 0 numsiginfo 0 23 1024 1024 0 tcpsndbuf 137984 17878480 20480000 20480000 0 tcprcvbuf 114688 6983504 20480000 20480000 0 othersockbuf 162960 1074440 20480000 20480000 0 dgramrcvbuf 0 24208 10240000 10240000 0 numothersock 101 353 2048 2048 0 dcachesize 459171 747444 10240000 10240000 0 numfile 1010 4221 50000 50000 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 39 424 2048 2048 0

  Read the article

< Previous Page | 611 612 613 614 615 616 617 618 619 620 621 622  | Next Page >