Search Results

Search found 22308 results on 893 pages for 'floating point'.

Page 617/893 | < Previous Page | 613 614 615 616 617 618 619 620 621 622 623 624  | Next Page >

• FTP through HAProxy

  - by Menda

  I have a machine, which is the Host and has HAProxy installed in it and working. Then I have a Guest KVM virtual machine running inside the Host with an IP 192.168.122.152. I installed an FTP server in the Guest machine with VSFTPD. From the Host, if I try the command $ ftp -p 192.168.122.152, works perfectly and I can connect to the Guest FTP. I need to remark that this FTP is configured as passive, but both passive and active connections are working from the Host. This is an extract of part of /etc/vsftpd.conf in the Guest: # Passive mode connect_from_port_20=NO tcp_wrappers=YES listen_address=192.168.122.152 pasv_enable=YES pasv_promiscuous=NO port_enable=YES port_promiscuous=NO pasv_max_port=10000 pasv_min_port=10250 Now it's time to make it accessible from outside, so I configure /etc/haproxy/haproxy.cfg like this: listen FTP_Default *:21 server ftp01 192.168.122.152 check port 21 inter 10s rise 1 fall 2 listen FTP_Range *:10000-10250 server ftp01 192.168.122.152 check port 21 inter 10s rise 1 fall 2 But if I try to connect from other machine in internet $ ftp -p $PUBLICIP, it only responds: Connected to <PUBLICIP>, but it doesn't ask for the login and password. Something in the HAProxy config must be wrong, because it's the only point where it fails. By the way, I tried to adapt my configuration to this one in this blog. Thanks.

  Read the article

• Postgres - could not create any TCP/IP sockets

  - by Jacka

  I'm running a rails app in development with postgresql 9.3. When I tried to start passenger server today, I got: PG::ConnectionBad - could not connect to server: Connection refused Is the server running on host "localhost" (217.74.65.145) and accepting TCP/IP connections on port 5432? No big deal I thought, that happened before. Restarting postgres always solved the problem. So I ran sudo service postgresql restart and got: * Restarting PostgreSQL 9.3 database server * The PostgreSQL server failed to start. Please check the log output: 2014-06-11 10:32:41 CEST LOG: could not bind IPv4 socket: Cannot assign requested address 2014-06-11 10:32:41 CEST HINT: Is another postmaster already running on port 5432? If not, wait a few seconds and retry. 2014-06-11 10:32:41 CEST WARNING: could not create listen socket for "localhost" 2014-06-11 10:32:41 CEST FATAL: could not create any TCP/IP sockets ...fail! My postgresql.conf points to the defaults: localhost and port 5432. I tried changing the port but the error message is the same (except the port change). Both ps aux | grep postgresql and ps aux | grep postmaster return nothing. EDIT: In postgresql.conf I changed listen_addresses to 127.0.0.1 instead of localhost and it did the trick, server restarted. I also had to edit my applications' db config and point to 127.0.0.1 instead of localhost. However, the question is now, why is localhost considered to be 217.74.65.145 and not 127.0.0.1? That's my /etc/hosts: 127.0.0.1 local 127.0.1.1 jacek-X501A1 127.0.0.1 something.name.non.example.com 127.0.0.1 company.something.name.non.example.com

  Read the article

• Rebuilding array on 3ware 9690SA-8I

  - by Tim Jones

  I have a RAID10 (8x1TB) array on a 3ware 9690 card running on an Ubuntu 1110 server. There was a kernel update so I scheduled a reboot after which the array was inaccessible. I checked the status a drive has died in the array, but the controller has thrown the entire array into an 'inoperable' state instead of simply degraded (what's the point of the RAID now ;-). After taking out the 'dead' drive I run a quick test to find it completely functional without a bad sector to be found. I try to put the drive back in but the array still marks the disk as degraded (remembering serial number or something??) and the entire array as inoperable... So I swap it out for a known working drive (not the same capacity but higher - should still work) and initiate a rebuild with the the new drive as a replacement. This fails instantly with the error "(0x0B:0x0033): Unit busy : Failed to start Rebuild on Unit 0". The unit shouldn't be busy as it is not mounted (the card itself is listed with lshw but the array it provides is not). I'm pretty much at an impasse now, I don't understand how I can have a single drive failure on a RAID10 that makes the entire array inaccessible, degraded I could understand but inaccessible?? I don't think the controller as prior to the reboot it was completely functional.

  Read the article

• Unpacking a ZTE ZXV10 H108L router firmware

  - by v3ng3ful

  I binwalked a firmware of a ZTE ZXV10 H108L, and got some encouraging results of uImage uboot, and LZMA compression, as well as a Squashfs 3.0 LZMA compressed filesystem. 256 0x100 uImage header, header size: 64 bytes, header CRC: 0xE70BCBB9, created: Thu Nov 10 04:54:54 2011, image size: 804172 bytes, Data Address: 0x80002000, Entry Point: 0x80266000, data CRC: 0x6EFE90F1, OS: Linux, CPU: MIPS, image type: OS Kernel Image, compression type: lzma, image name: MIPS Linux-2.6.20 320 0x140 LZMA compressed data, properties: 0x5D, dictionary size: 8388608 bytes, uncompressed size: 2637958 bytes 851968 0xD0000 Squashfs filesystem, big endian, lzma signature, version 3.0, size: 2543403 bytes, 632 inodes, blocksize: 65536 bytes, created: Thu Nov 10 04:56:12 2011 Now what I did is, to test several portions of the file (320byte-end, 851968byte-end, and many more) using dd, and trying with certain tools to uncompress/unpack the filesystem of the firmware. After some digging I found out the best tool to do this is the firmware_mod_kit, that understands a squashfs-lzma v3 filesystem. Although I ended up really frustrated as unsquashfs-lzma v3 reported a cold "zlib::uncompress failed, unknown error -3". Do you have any ideas? Could it be that, the firmware is corrupted on purpose to discourage attempts like this? Router file Thanks

  Read the article

• High CPU usage by 'svchost.exe' and 'coreServiceShell.exe'

  - by kush.impetus

  I am having a laptop running on Windows 7 Ultimate 32-bit. Since past few days, my laptop is facing a serious problem. Whenever I connect to Internet, either svchost.exe or coreServiceShell.exe or both hog the CPU. The coreServiceShell.exe consumes a lot of RAM also. Going into the details, I found that high CPU usage of svchost.exe is caused by Network Location Awareness service. And the high CPU usage of coreServiceShell.exe is caused by Trend Micro Titanium Internet Security 2012. That kind'a makes me think that Trend Micro may be the root of the problem. After further testing, I found that if I use IE or Firefox to browse the Internet, immediately after connecting to Internet, things are normal. See and But if I use Google Chrome, the coreServiceShell.exe hogs both CPU and RAM. At this point, if I disconnect the Internet, the CPU and RAM usage by coreServiceShell.exe continues to be high till I close the Chrome. Also, when I close the Chrome, while Internet is connected, svchost.exe continues to hog CPU but coreServiceShell.exe leaves the race. That makes think that Chrome is the root of the problem, but again, tracing coreServiceShell.exe takes me back to Trend Micro Internet Security. Stopping the Protection by the Trend Micro Internet Security doesn't help either (I am not able to stop its services though). I have updated the Chrome, but no help. I just can't figure out who is the culprit. I can't do without the Google Chrome (of course, by not using it) because of its immensely useful and indispensable features both during browsing and development. Secondly, I can't uninstall the Trend Micro Internet security Suite since it still has few months before it expires and is proving me reliable protection. What could be the cause of the problem and what can I do to resolve this? Thanks in advance

  Read the article

• RouterOS on Hyper-V (v3/2012) - any way to get it working?

  - by TomTom

  Trying to set up a small VPN point to connect into a remote Hyper-V cluster using ROuterOS. Anyone got it working ON Hyper-V with the latest builds of RouterOS? It seems the legacy network adapter is not supported anymore either (or just broken). The platform is a Windows Server 2012 RC. This is not a high performance setup - the RouterOS wont do the routing for more than the backend administrative access, and the only real traffic we will see there is when ISO images for new operating systems are uploaded. Otherwise we will have possibly RDP traffic as well as web / http traffioc, but this is internal only (dashboards, some control panel). The server has no public business. So the price for non virtualized network cards is ok for me. After hooking up - ping just does not work. After some time I see in windows (arp -a on the command line), so I know that the Hyper-V side is set up properly. Just no packets arrived. I have turned off all protection on Hyper-V (or : not turned them on), so no MAC spoofing protection etc. in the Advanced page for the legacy adapters. Unless I can get it work I will have to resort to using a windows install as router / VPN endpoint, which introduces another OS into the fabric (we run all routers etc. so far on mikrotik in hardware, which is why I want this one to be RouterOS, too). And no, putting hardware there is NOT an option - the cost would be significant.

  Read the article

• TortoiseSVN hangs in Windows Server 2012 Azure VM

  - by ZaijiaN

  Following @shanselman's article on remoting into an Azure VM for development, I spun up my own VS 2013 VM, and that image runs on WS 2012. Once I was able to remote in, I started installing all my dev tools, including Tortoise SVN 1.8.3 64bit. Things went south once I started attempting to check out code from my personal svn server. It would hang and freeze often, although sometimes it would work - I was able to partially check out projects, but I would get frequent connection time out errors. My personal svn server (VisualSVN 2.7.2) runs at home on a windows 7 machine, and I have a dyndns url pointing to it. I have also configured my router to passthrough all 443 traffic to the appropriate port on the server. I self-signed a cert and made sure it was imported into the VM cert store under trusted root authorities. I have no problems connecting to my svn server from 4-5 other computers & locations. From the Azure VM, in both IE and Chrome, I can access the repository web browser with no issues. There are no outbound firewall restrictions. I have installed other SVN add-ons for Visual Studio (AnkhSVN, VisualSVN) and attempted to connect with my svn server, with largely the same results - random and persistent connection issues (hangs/timeouts). I spun up a completely fresh WS 2008 Azure VM, and installed TortoiseSVN, and had the same results. So I'm at a loss as to what the problem is and how to fix it. Web searches on tortoisesvn and windows server issues doesn't yield any current or relevant information. At this point, i'm guessing that maybe some setting or configuration that MS Azure VM images is the culprit - although I should probably attempt to spin up my own local WS VM to rule out that it's a window server issue. Any thoughts? I hope I'm just missing something really obvious!

  Read the article

• Kernel panic while loading Mac OS X on VMWare

  - by Vladimir Gritsenko

  I have Mac OS X 10.6.3 and VMWare 7.1. Trying to run the OS X doesn't work - shortly after booting VMWare announces the machine's death with this pop-up message: The CPU has been disabled by the guest operating system. You will need to power off or reset the virtual machine at this point. The console has a more interesting announcement: The real-time clock was not properly initialized on your system! With a dump of the detected CPU speed (~2.9 GHz), FSB (~94 MHz) and bus ratio (31). Somehow, the code that panics is documented in an accidental .diff file here. Apparently, it commits seppuku if the bus ratio is greater than 30. I underclocked my E6500 to a slower speed, but this apparently didn't make any difference. I can think of two possibilities right now: The CPU info being read is constant, and defines the maximum ability of the CPU. In which case it appears I'm screwed. VMWare presents its own CPU info to the machine, which I can perhaps somehow change. If so, how? If these sound completely off, that's because I'm a real newbie in these matters. Here's hoping you guys can show me the light :-)

  Read the article

• Diagnosing permission problems with Cobian Backup to network share

  - by DaveBurns

  I'm running the latest Cobian 11. I have a Synology DS412 NAS. All of my machines (Mac and Windows) access this just fine when I'm logged in and I browse to it manually. I have Cobian installed as a service on two Windows machines: WinXP SP3 and Win7 x64. On both machines, the service is set to log on with my user account which is in the Windows administrator group. Backups on both machines fail with the message "Couldn't create the destination directory "\nas1\backups\foo\bar\": The filename, directory name, or volume label syntax is incorrect". I have tried setting the NAS's share to allow anonymous read/write access but it made no difference. Although I want the backups to run unattended in the middle of the night, I have tested them by running them manually while I'm logged in but no luck. Before starting that, I make sure that I can browse to the NAS with Explorer to ensure that any authentication session with Windows and the NAS has not expired. Still no luck. I have tried creating that destination directory both on the NAS before the backup and deleting it so the backup job could create it with the client's credentials but no luck. The usual answer in the Cobian support forums is that there is a permission problem. I agree. But at this point, what can I do to diagnose this further?

  Read the article

• This operation has been canceled due to restrictions in effect on this computer. Please contact your

  - by WebDude

  I am having a highly annoying problem on Windows 7 with Microsoft Outlook 2007. Whenever I click on any hyperlinks I am present with the message This operation has been canceled due to restrictions in effect on this computer. Please contact your system administrator and let's not forget the most ear-piecing "DING" to accompany this wonderful informative message. Now I have searched the web high and low for a solution here and most sources suggest the same solution of resetting your IE as your default browser. Tried .. failed A lot of sources suggest this has something to do with installing and uninstalling chrome. I have never installed Chrome but am actually consdering this to see if it by some chance fixes my computer. A lot of sources also point to a microsoft kb article 325478 which is focused around Windows XP and totally unrelated to my problem. I see there are some other queries on SuperUser with no resolution. Please can someone help solve this highly annoying issue. I am running Window 7 professional x64 Microsoft Office 2007 Microsoft Security Essentials Running in a windows work group with default policy settings HELP!

  Read the article

• Mod Rewrite Help - Pseudo-Subdirectories

  - by Gimpyfuzznut

  I am dealing with a frustrating problem with Joomla that is going to require some url trickery. The idea is straight-forward but after reading a bunch of guides for mod-rewrite, I still can't seem to get it work. Let's say my site is www.mysite.com. Joomla is already performing some rewriting for SEF urls so I have links like www.mysite.com/home and www.mysite.com/news and so on. I want to be able to have (4) pseudo-subdirectories like www.mysite.com/mode1/ and www.mysite.com/mode2/ and so on. These subdirectories should work as if the subdirectory isn't there, ie both www.mysite.com/mode1/home and www.mysite.com/mode2/home should pull up the same www.mysite.com/home. It should point any www.mysite.com/mode1/anypagehere to www.mysite.com/anypagehere. The reason I am asking for this is because I will be reading the url for mode1, mode2, etc, to modify the template page. There will be a landing page that will direct people to /mode1/ and /mode2/ etc and the template will change based on that. Note, that I don't want to actually pass a parameter to the url accessible by a GET or whatever because Joomla removes it (perhaps because of my current mod_rewrite settings). I've pasted the current .htaccess file. RewriteBase /joomla ##########Rewrite rules to block out some common exploits RewriteCond %{QUERY_STRING} mosConfig_[a-zA-Z_]{1,21}(=|\%3D) [OR] # Block out any script trying to base64_encode crap to send via URL RewriteCond %{QUERY_STRING} base64_encode.*\(.*\) [OR] # Block out any script that includes a <script> tag in URL RewriteCond %{QUERY_STRING} (\<|%3C).*script.*(\>|%3E) [NC,OR] # Block out any script trying to set a PHP GLOBALS variable via URL RewriteCond %{QUERY_STRING} GLOBALS(=|\[|\%[0-9A-Z]{0,2}) [OR] # Block out any script trying to modify a _REQUEST variable via URL RewriteCond %{QUERY_STRING} _REQUEST(=|\[|\%[0-9A-Z]{0,2}) # Send all blocked request to homepage with 403 Forbidden error! RewriteRule ^(.*)$ index.php [F,L] ########## Begin - Joomla! core SEF Section RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} !^/index.php RewriteCond %{REQUEST_URI} (/|\.php|\.html|\.htm|\.feed|\.pdf|\.raw|/[^.]*)$ [NC] RewriteRule (.*) index.php #RewriteRule .* - [E=HTTP_AUTHORIZATION:%{HTTP:Authorization},L] ########## End - Joomla! core SEF Section

  Read the article

• Task scheduler "hidden" only hides task, not process

  - by Brandi

  I am trying to make an application that acts like a desktop application for all the computers in our network. I have already got a windows forms app that works like I want it to, and I'm using the task scheduler to start it on login. We would really like it if the process as well as the task is hidden from the task manager in order to avoid accidental deletion. Selecting "Hidden" in the task scheduler hides the task (good!) but the process is still visible (not good enough). I tried using the option to run as "SYSTEM" or "LOCAL SERVICE" so that the user would get "access denied" when trying to delete or just wouldn't even view it by default. However, running as a service makes the process invisible on Vista and 7, and the point of my app is to display information interactively. (User can click, sort, etc). Is there any other alternatives to either run the process as someone/something besides the logged in user and still have the logged on user be able to see and interact with it? (Therefore it would list as someone else's app?) From what I've read on the internet, the only ways to actually hide something from the task manager seem hacky and/or difficult and rather involved. I don't really want to write a bunch of C or whatever only to maybe not have it work on Vista/7 anyway. Besides which, for a legitimate app with a legitimate use, I shouldn't have to go to those extremes... I see "Access Denied" all the time for system processes... why is it so hard for me to do the same? So does anyone have any simple solutions? Is it easier than I think to just list something in the task manager as another user? Thanks in advance for any replies.

  Read the article

• syspolicy_purge_history generates failed logins

  - by jbrown414

  I have a development server with 3 instances: Default, A and B. It is a physical server, non clustered. Whenever the syspolicy_purge_history job runs at 2 am, I get failed login alerts. Looking at the job steps, all are successfully completed. It appears that some point during the step "Erase Phantom System Health Records" is when the failed logins occur. syspolicy_purge_history on instance B works OK. syspolicy_purge_history on the Default instance seems to want to connect to instance B, resulting in: Error: 18456, Severity: 14, State: 11. Login failed for user 'Machinename\sqlsvc-B'. Reason: Token-based server access validation failed with an infrastructure error. Check for previous errors. [CLIENT: <local machine>] . No errors are reported by Powershell. syspolicy_purge_history on the A instance seems to want to connect to the Default instance resulting in Error: 18456, Severity: 14, State: 11. Login failed for user 'Machinename\sqlsvc-Default'. Reason: Token-based server access validation failed with an infrastructure error. Check for previous errors. [CLIENT: <local machine>] . Then it tries to connect to the B instance, resulting in Error: 18456, Severity: 14, State: 11. Login failed for user 'Machinename\sqlsvc-B'. Reason: Token-based server access validation failed with an infrastructure error. Check for previous errors. [CLIENT: <local machine>] . No errors are reported by Powershell. I tried the steps posted here hoping they would fix it. http://support.microsoft.com/kb/955726 But again, this is not a virtual server nor is it in a cluster. Do you have any suggestions? Thanks.

  Read the article

• SQL Server 2008 Cluster Installation - First network name always fails

  - by boflynn

  I'm testing failover clustering in Windows Server 2008 to host a SQL Server 2008 installation using this installation guide. My base cluster is installed and working properly, as well as clustering the DTC service. However, when it comes time to install SQL Server, my first attempt at installation always fails with the same message and seems to "taint" the network name. For example, with my previous cluster attempt, I was installing SQL Server as VSQL. After approximately 15 attempts of installation and trying to resolve the errors, e.g. changing domain accounts for SQL, setting SPNs, etc., I typoed the network name as VQSL and the installation worked. Similarly on my current cluster, I tried installing with the SQL service named PROD-C1-DB and got the same errors as last time until I tried changing the name to anything else, e.g. PROD-C1-DB1, SQL, TEST, etc., at which point the install works. It will even install to VSQL now. While testing, my install routine was: Run setup.exe from patched media, selecting appropriate options After the install fails, I'd chose "Remove node from a SQL Server failover cluster" and remove the single, failed, node Attempt to diagnose problem, inspect event logs, etc. Delete the computer account that was created for the SQL Service from Active Directory Delete the MSSQL10.MSSQLSERVER folder from the shared data drive The error message I receive from the SQL Server installer is: The following error has occurred: The cluster resource 'SQL Server' could not be brought online. Error: The group or resource is not in the correct state to perform the requested operation. (Exception from HRESULT: 0x8007139F) Along with hundreds of the following errors in the Application event log: [sqsrvres] checkODBCConnectError: sqlstate = 28000; native error = 4818; message = [Microsoft][SQL Server Native Client 10.0][SQL Server]Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. System configuration notes: Windows Server 2008 Enterprise Edition x64 SQL Server 2008 Enterprise Edition x64 using slipstreamed SP1+CU1 media Dell PowerEdge servers Fibre attached storage

  Read the article

• How do you install/configure JBoss on Linux/Unix?

  - by mafro

  I'm currently working on how install and configure multiple (30+) JBoss EAP 5 configurations (both standalone and clusters) for development, test and production at a client's site (running SuSE). I'm not to fancy about the jboss way of storing application/configuration together with system files, so I have tried to split things up (ie moving server config out of the jboss installation directory). I also would like minimize the amount of configuration needed when upgrading/patching jboss - but I'm not done thinking about that... It would be great to hear how you've done and what you think about my approach. This is how my installations look like (for the moment): Standard JBoss EAP install (minus server configs): /opt/jboss/jboss-eap-5.0/jboss-as /opt/jboss/jboss-eap-5.0/jboss-as/bin/ /opt/jboss/jboss-eap-5.0/jboss-as/lib/ /opt/jboss/jboss-eap-5.0/jboss-as/server/ [server configs removed to avoid starting them by mistake] /opt/jboss/jboss-eap-5.0/jboss-as/.../ Application (some jboss folders has been omitted - you'll get the point anyway): /app/<project>/ [$app.dir - application specific base folder] /app/<project>/jboss/ [$jboss.home] /app/<project>/jboss/bin/ -> /opt/jboss/jboss-eap-5.0/jboss-as/bin /app/<project>/jboss/lib/ -> /opt/jboss/jboss-eap-5.0/jboss-as/lib /app/<project>/jboss/server/<cfg>/ [project specific config based on 'production'] /app/<project>/jboss/server/<cfg>/log/ -> /log/<project>/<cfg> /app/<project>/jboss/server/<cfg>/... /app/<project>/jboss/.../ -> /opt/jboss/jboss-eap-5.0/jboss-as/.../ /app/<project>/bin/ [application specific scripts for start/stop etc - wraps jboss supplied scripts] /app/<project>/deploy/ [application deploy folder] /app/<project>/etc/ [application specific config] Questions: How do you install JBoss (on linux/unix systems)? Where do you put JBoss and what modifications do you do? Where do you put your applications and application specific files? Do you share JBoss instances between applications or run one instance/cluster per application? How do you manage configuration changes (i.e. your modifications of jboss standard config)?

  Read the article

• FTP Error: 550 Cant change directory to /: Permission denied

  - by Alessandro Merletti de Palo

  I installed Pureftpd and Ispconfig3 on my server. Starting from the point I'll probably uninstall ispconfig3 and make things directly on the server, now I am so stubborn I really want to see where's the problem. I created a ftp user through ispconfig, named amdpftp. It is related to a server user named web7. It logs in with username and password, but if i try to ls, it tells me: FTP Error: 550 Cant change directory to /: Permission denied I thought many things, like: 1. It is a problem of permissions. I went to /var/www/clients/client0/web7 , it was immutable and owned by root. Chattr -i and chown web7:client0 changed permissions, but with no effect. I restored to root:root, and made it immutable again. 2. I make some mistakes in the pureftpd installation: Wrong, it works pretty fine. The pureftpd.log doesn't seem to say anything bad. 3. The pureftpd.log file is only the pureftpd one, I should also check the mysqld functionality, as it is in a mysql database that user, password and working directory are stored. I enabled logging in the my.cnf, but also in the ispconfig database operation there wasn't anything wrong. Then I mkdir testftp in /var/www, chown web7:client0, and edited amdpftp user root directory from /var/www/clients/client0/web7 into /var/www/testftp . Guess what? It worked. So, now I know: 1. The PureFtpd works pretty fine 2. The mysql ispconfig database as well 3. The username and password of the virtual user created by ispconfig into pureftpd work 4. The correlation between username and password and the user web7 and the group client0 does work. What kind of magic has been cast upon the ispconfig directories [/var/www/clients/*] that block ftpusers to operate?

  Read the article

• How do I leverage Bitlocker cmdlets?

  - by user1418882

  This article hints at being able to unlock a bitlocked drive using: Unlock-BitLocker -MountPoint -Password However, I know diddly squat about Powershell and how to use the Powershell cmdlets to do what I want to do. So, how do I do use the above to do something like the following? Unlock-BitLocker -MountPoint D:\ -Password "password" Currently about as much as I know how to do is start Powershell and that's it. I don't want to learn masses of Powershell to get to the point where I can do this. All that I need to know in enough to know how I can execute the commands that are pointed out in the first link. So far in the powershell prompt if I past in: Unlock-BitLocker -MountPoint D:\ -Password "password" I get the following error: The term 'Unlock-BitLocker' is not recognized as the name of a cmdlet, function, script file, or operable program. Chec k the spelling of the name, or if a path was included, verify that the path is correct and try again. At line:1 char:17 + Unlock-BitLocker <<<< -MountPoint D:\ -Password "password" + CategoryInfo : ObjectNotFound: (Unlock-BitLocker:String) [], CommandNotFoundException + FullyQualifiedErrorId : CommandNotFoundException This is most likely because I don't have any clue about how the commands on the initially linked page work in a powershell context. This is so that I can answer my own question here: Bitlocker and scheduled task (powershell) script to unlock non-system drive

  Read the article

• powershell v2 remoting - How do you enable unecrypted traffic

  - by Peter Walke

  I'm writing a powershell v2 script that I'd like to run against a remote server. When I run it, I get the error : Connecting to remote server failed with the following error message : The WinRM client cannot process the request. Unencrypted traffic is currently disabled in the client configuration. Change the client configurati on and try the request again. For more information, see the about_ Remote_Troubleshooting Help topic. I looked at the online help for about _ Remote_Troubleshooting, but it didn't point me towards how to enable unecrypted traffic. Below is the script that I'm using that is causing me problems. Note: I have already run Enable-PSRemoting on the remote machine to allow it to accept incoming requests. I have tried to use a session option variable, but it doesn't seem to make any difference. $key = "HKLM:\SOFTWARE\Microsoft\PowerShell\1\ShellIds" Set-ItemProperty $key ConsolePrompting True $tvar = "password" $password = ConvertTo-SecureString -string $tvar -asPlainText –force $username="domain\username" $mySessionOption = New-PSSessionOption -NoEncryption $credential = New-Object System.Management.Automation.PSCredential($username,$password) invoke-command -filepath C:\scripts\RemoteScript.ps1 -sessionoption $mySessionOption -authentication digest -credential $credential -computername RemoteServer How do I enable unencrypted traffic?

  Read the article

• map subdomain to another subdomain via cname

  - by Stephen

  Question: I need to get DNS configured to point a subdomain from one domain (which I will generally not be controlling) to another subdomain on a different domain name. Testing this process using a simple CNAME entry keeps pointing to the primary domain and not the subdomain where it should be going. This is the scenario; (newdomain.com is in my control) cdn.xyz.com should display content from this subdomain subdomain.newdomain.com It is instead displaying content from newdomain.com (not the subdomain sub domain) cdn.xyz.com/page.htm displays content from newdomain.com/page.htm although what I need is it to display content from subdomain.newdomain.com/page.htm Other Background: setup is between two different servers with different IP ranges although DNS cluster is on between all servers the newdomain.com is set up with its own unique IP (which is on the A records for the subdomains, the subdomains work as expected/normal) the DNS entry is correct (cdn CNAME subdomain.newdomain.com.) ie the end period is included a DNS lookup on the CNAME externally reports back as subdomain.newdomain.com. as the record Does anyone know what DNS entries I am missing to get this working correctly ? Note: I do not want to just put a redirect between domains as I need the content of subdomain.newdomain.com/content.html to be visible via the URL of cdn.xyz.com/content.html also I can just use some redirects on newdomain.com to achieve what I am after but would prefer to just get the DNS correct. EDIT Current DNS cdn CNAME subdomain.newdomain.com. || CNAME entry for domain1 subdomain A XXX.XXX.XXX.XXX || A record entry for working subdomain pointing to unique IP What should happen is that cdn.domain1.com - subdomain.newdomain.com What is happening is cdn.domain1.com - newdomain.com (ie. the root not the subdomain) EDIT 2 Actually if its easier I am trying to emulate a simple cloud setup like Rackspace Containers (which I assume is similar to Buckets on AWS). although it is not for cloud storage Where a container has a url reference of hd62321678d323.rackspace.com (in truth they are much longer) so I can use a CNAME record of: cdn CNAME hd62321678d323.rackspace.com. so that http://cdn.mydomain.com/myfile.jpg displays content from http://hd62321678d323.rackspace.com/myfile.jpg

  Read the article

• linux LVM mirror vs. MD mirror

  - by sims

  I think I remember making some mirrors years ago with LVM, and I don't remember this "log" thing. Or maybe I made the mirror with mdadm and put LVM on top. That must be it. What is the LVM log for if it is just a mirror? What is stored there? What is it's purpose? Is using "--mirrorlog core" bad? What's the down side? I don't want to have to have another partition for logs if I don't have to. Any recommendations on using either technology? Even if I make the mirror with mdadm, I'll use LVM on top of that. So, in that case, maybe it's better to have the whole setup built with LVM...? Would that take more a performance hit or less? The disks are for storing Xen domU "disks". Sorry for the complex not-to-the-point "question". Ideas and suggestions and links are most welcome. Thanks!

  Read the article

• Android SDK emulator freezes on a Mac running OS X 10.6 Snow Leopard

  - by Donald Burr

  I'm having trouble running the Android SDK on both of my Macs running OS X 10.6.2 Snow Leopard. This appears to be a 64 bit vs. 32 bit issue, as Snow Leopard now defaults to 64-bit everything, including the Java virtual machine. I found this webpage with instructions on how to get the Android tools to run in the 32-bit Java VM, and I am now able to run the Android GUI tool to download SDK files, create AVM's, etc. However, when I try the Hello World tutorial and get to the point where I run my application under the Android emulator, everything goes south. The emulator appears to start but it hangs (spinning beachball of death cursor) without displaying anything. (This only hangs the emulator; the rest of the system still works fine.) If I follow the exact same steps (minus the 32-bit java hack) in a Windows virtual machine, everything works fine. Googling didn't yield anything useful (except for the 32-bit java hack I spoke of earlier). This occurs on both my Mac Pro tower and 13" MacBook Pro. Does anyone have any suggestions?

  Read the article

• Windows 8 DLNA streaming of MKV files

  - by dbb

  I have a Samsung TV that is capable of playing MKV files. The Windows DLNA Play To menu that appears when you right-click a media file does not support MKV files, but a simple trick has been to change the file extension from .mkv to .avi so the Play To context menu item would appear. At that point I could successfully stream from my computer to my TV. However, this does not appear to work in Windows 8. Doing the same thing in Windows 8 causes the Play To window to open but the file does not get played. Dragging and dropping the file in the Play To window causes it to be silently ignored. Using actual AVI, MP4, etc. files works, of course. It appears Windows 8 is now doing some kind of validation on the file that Windows 7 wasn't previously. The Play To window does not show any kind of obvious error message or warning and there is nothing in the Windows event log. So, is there a way in Windows 8 to stream MKV files to a DLNA device without converting it to another container format? I would rather not use extra third-party software, but I would consider it if it's purposefully designed for this simple case rather than a more robust "media library/server" solution.

  Read the article

• Invalid format for New Relic licence when installing on Elastic Beanstalk

  - by BenFreke

  We've created an app that is running on an Elastic Beanstalk instance, 64 bit PHP version 5.4 (so not legacy). I've used the New Relic installation instructions to install New Relic, and viewing phpinfo shows that New Relic is installed. However, I'm not getting any data in New Relic and that is because it is saying that the licence is ***invalid format*** under newrelic.licence I'm getting the licence from my New Relic account, and it is a 40 character hexadecimal string. Here is the current newrelic.config file in the .ebextensions folder I'm using, with most of the licence key commented out. packages: yum: newrelic-php5: [] rpm: newrelic: http://yum.newrelic.com/pub/newrelic/el5/x86_64/newrelic-repo-5-3.noarch.rpm commands: configure_new_relic: command: newrelic-install install env: NR_INSTALL_SILENT: true NR_INSTALL_KEY: ec9a4... Skitch of relevant phpinfo Can anyone shed some light on what's going on here? I've tried two different New Relic licence keys with the same error, I've also surrounded it with a single quote mark and tried uppercase only. And at this point I'm out of ideas on what to try. We're not AWS gurus so it could very easily be something simple like not opening a port to allow the licence to be validated?

  Read the article

• i5 540M or i7 720QM for laptop running VMs and software development tools?

  - by Donald Hughes

  I'm a software developer that would primarily be running Windows 7 as the primary operating system. On a typical day, I might, at any given moment, be running Visual Studio, Expression Web, SQL Server developer (and Management Console), IIS, Photoshop, a dozen browser tabs in 2-3 different browsers, Skype video chat, streaming music, and a couple of VMs (WinXP and Ubuntu) for testing/experimentation. Obviously, RAM is a concern, which is why I plan to use 8 GB so I can devote enough to the VMs to be usable. I'm also tempted to use an ExpressCard SSD for storing the VM disks to ease disk contention. And I know that that is asking a lot from a laptop, and I should just use a desktop, but I need to be able to take my work with me between several locations. It seems that at a reasonable price point, it comes down to the i5 540M versus the i7 720QM. I'm leaning toward the i7 since it would allow me to dedicate a whole hyperthreaded core to each VM, and still have two cores left for the primary OS. I've heard that the i5 has better battery life, but I'm curious for my scenario if there would be a meaningful difference. I don't usually work without a plug, but I do occasionally ride the train or fly and it would be nice to have at least 3 hours of juice for unusual circumstances. And, finally, for this usage scenario, would a dedicated video option be preferred over the i5's integrated video? It sounds like Visual Studio 2010 (and Windows 7) can take advantage of the video card.

  Read the article

• Why is my mouse randomly deselecting and unclicking?

  - by Coldblackice

  (Windows 7 x64, Logitech MX1100 mouse) If I click/hold/ the mouse, like on the title bar of a folder to move it, or to select text, the mouse will randomly "unselect" it and then randomly reselect at another point in the movement. For example, if I were to start mouse-selecting the above paragraph, starting with "movement." and then moving backwards, it might select as far as "reselect", but then the selection would disappear, only to start selecting again from "will randomly". I realize this would sound like a clear-cut case for a hardware issue in the mouse button, but I've narrowed out that that's not the case. The problem doesn't happen if I drag-move/drag-select slowly. But I can make the problem very apparent if I click and drag something fast. For example, if I click and hold the title bar of a window, and then start quickly dragging it around in circles across my monitor, the window will get "dropped", and a new window will get picked up in the process. Additionally, if I right-click anywhere to get a context menu (in Windows, programs, anywhere/everywhere), and then relatively quickly press the left mouse button to select something on the context menu, the context menu will disappear as if I had clicked "through" it. I haven't had any driver changes, system updates, or significant software changes/updates/installations recently, that might be a precursor to this issue. Again, the oddity seems to be the "speed" of action. Another note -- it seems that "lag" has a bit to do with it. If I click and drag a window around quickly, it might start to "lag" a tad bit, like it's perhaps moving too fast for Windows to keep up with the refresh/redraw rate, and that's usually synonymous with this odd deselect bug happening. (Batteries fully charged, no damage or recent changes to mouse, no changes that might affect/block wireless communication)

  Read the article

< Previous Page | 613 614 615 616 617 618 619 620 621 622 623 624  | Next Page >