Search Results

Search found 2042 results on 82 pages for 'booting'.

Page 62/82 | < Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >

  • Unable to start after 13.04 > 13.10 udate

    - by romainl
    At the end of the update process, clicking on the Restart button had no visible effect whatsoever. After waiting 5 to 10 minutes, I decided to reboot the computer manually. Since then, I rebooted a good dozen times (not with the hope that it would work but with the hope of reading the messages) with the same non-result and the same symptoms: I get the ASCII text-on-purple Ubuntu 13.10 . . . . splash screen with these messages: * Restoring resolver state... [OK] * Starting crash report submission daemon [OK] * Starting CUPS printing spooler/server [OK] Everything disappears. The whole process hangs at a purple screen with the mouse cursor right in the middle. At this point, I'm unable to use the mouse and the keyboard. Booting from a 12.04 CD works perfectly, Disk Utility says that all my disks are OK and I can mount my main partition without problems. Something obviously went wrong at the end of the upgrade but I have no idea what. I'd appreciate any pointer. This is the kind of moment where you really think "Next time, I'll separate my /home partition for sure". My machine is an aging but working Dell Inspiron 530 with an Intel Core Duo E2160 processor, 2 GHz of RAM and an ATI Radeon HD3650 video card. Thanks.

    Read the article

  • Ubuntu 12.04 startup is slow and dmesg output seems to lose several seconds

    - by cdowen
    I use ubuntu on Dell Inspiron n4050.I have upgraded to ubuntu 12.04 from 10.04. But now I find the system startup is a little slow and plymouth only show purple screen without logo during startup. When I use dmesg, it shows such messages: [ 2.497750] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 2.603028] usb 2-1.6: new high-speed USB device number 3 using ehci_hcd [ 2.715538] Initializing USB Mass Storage driver... [ 2.715594] usbcore: registered new interface driver usb-storage [ 2.715596] USB Mass Storage support registered. [ 21.317843] Adding 2000892k swap on /dev/sda5. Priority:-1 extents:1 across:2000892k [ 21.323724] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 21.391450] udevd[431]: starting version 175 I wonder what it is doing between 2 second and 21 second. Is it related to being so slow? I tried bootchart. It gave me a complex picture. Sorry I can't post it here. http://3.bp.blogspot.com/-7LX8T5uQvlw/UKhdFMVkp4I/AAAAAAAAADg/dtxePkE94mg/s320/lengzhen-ubuntu-precise-20121118-1.png While ubuntu is booting , I also noticed that it appears:/tmp is not ready or present And sometimes follows *Stop saving kernel messages. Is this the reason dmesg lost output?

    Read the article

  • Is full partition encryption the only sure way to make Ubuntu safe from external access?

    - by fred.bear
    (By "external access", I mean eg. via a Live CD, or another OS on the same dual-boot machine) A friend wants to try Ubuntu. He's fed up with Vista grinding to a crawl (the kids? :), so he likes the "potential" security offered by Ubuntu, but because the computer will be multi-booting Ubuntu (primary) and 2 Vistas (one for him, if he ever needs it again, and the other one for the kids to screw up (again). However, he is concerned about any non-Ubuntu access to the Ubuntu partitions (and also to his Vista partition)... I believe TrueCrypt will do the job for his Vista, but I'd like to know what the best encryption system for Ubuntu is... If TrueCrypt works for Ubuntu, it may be the best option for him, as it would be the same look and feel for both. Ubuntu will be installed with 3 partitions; 1) root 2) home 3) swap.. Will Ubuntu's boot loader clash with TrueCrypt's encrypted partition? PS.. Is encryption a suitable solution?

    Read the article

  • recovering raid 0 hard disk

    - by Hiawatha
    I bumped to a huge (for me) problem. I was running dual boot system (win 7 / linux) and at some point I decided to test fedora ( I am new in Linux ). My hard disk conf: 3 hard disks each 1 TB, 2 set to raid 0 with windows running on it and 1 for linux. After installing it from live usb I found out that windows 7 is not in grub anymore and while booting shows raid error. I installed back Ubuntu and ran Disk Utility and checked now I have one disks (raid 0) failed (READ) error. First has 5 bad sectors and second has 1 bad sector. And now I dont know what to do and how to repair. further I dont know which data i could provide to get help. I tried ntfsfix and got this output: Mounting volume... NTFS signature is missing. FAILED Attempting to correct errors... NTFS signature is missing. FAILED Failed to startup volume: Invalid argument NTFS signature is missing. Trying the alternate boot sector Unrecoverable error Volume is corrupt. You should run chkdsk. #sudo ntfs-3g -o force,rw /dev/sdb /media/windows NTFS signature is missing. Failed to mount '/dev/sdb': Invalid argument The device '/dev/sdb' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around?

    Read the article

  • after BIOS splash, will not boot -- asks me to select an OS, but it just reboots

    - by user92040
    I'm running Linux Mint 13 MATE 64-bit. Everything has been working for several weeks. Yesterday, when I tried to boot up my computer, after the BIOS screen flashes I reach a screen with a black background that reads at the top: GNU GRUB version1.99-21ubuntu3.4 Then there is a box in which I can select from the following lines: Linux Mint 13 MATE 64-bit, 3.2.0-31-generic (/dev/sdb2) Linux Mint 13 MATE 64-bit, 3.2.0-31-generic (/dev/sdb2) -- recovery mode Previous Linux versions Memory test (memtest86+) Memory test (memtest86+, serial console 115200) At the bottom it reads: Use the ? and ? keys to select which entry is highlighed. Press enter to boot the selected OS, 'e' to edit the commands before booting or 'c' for a command-line. I have no idea why it started doing this and, worse, I have no idea how to get out of here. No matter which option I select, I can't get it to boot the OS. If I select either of the first two, it reboots to splash the BIOS and then I'm right back where I started. If I choose "Previous Linux versions" I get essentially the same screen with only two choices (which are the same as the first two choices listed above, Linux 13 MATE and the recovery mode). Again, choosing either one of those results in a reboot. If I try to run either of the memtest options, it reads: error: unknown command 'linux16', Press any key to continue... Then it brings me back to the same screen Can anyone help me please? Intel Core i5-2500 ASUS P8Z68-V LX Intel Motherboard G. Skill Ripjaws series F3-12800CL9D-8GBRL (4GB x2) Plextor 128GB M5S Series SSD

    Read the article

  • after upgrade from 10.04 to 12.04 cannot boot with linux 3.2.0-24-generic-pae

    - by Ricardo
    After upgrade from 10.04 to 12.04, I cannot boot with linux 3.2.0-24-generic-pae: process gets frozen in a xubuntu initialization screen (I had qimo installed). If I try the recovery mode (with the same Linux version), booting freezes after this message: Begin: Mounting root file system. If in grub menu I choose Previous Linux versions, I can boot using Linux 2.6.32-41-generic-pae. But once logged in, some things don't seem to work (apt-get update fails, update manager fails, HID menu does not provide suggestions...) (to be honest, I have no idea whether this is part of the bigger issue) Reading in Ask Ubuntu through apparently similar problems, I decided to follow some advices: got boot-repair and run it. The problem remains & I got this report. I also run as root in terminal $ sudo update-initramfs -u and this is what I got: update-initramfs: Generating /boot/initrd.img-3.2.0-24-generic-pae cryptsetup: WARNING: failed to detect canonical device of /dev/sda1 cryptsetup: WARNING: could not determine root device from /etc/fstab /tmp/mkinitramfs_EIDlHy/scripts/classmate-bottom/45xconfig: 9: .: Can't open /scripts/casper-functions What else? My pc is Intel® Core™ i7 CPU 870 @ 2.93GHz × 8, graphs is GeForce 8400 GS/PCIe/SSE2, memory is 7,8 GiB. I have two questions: Is this a bug in the newest kernel I should report? Is there anything I can do appart from a fresh install?

    Read the article

  • Hard drive clicking noise on Acer AO722

    - by Blank
    I'm running Ubuntu 11.10 on an Acer Aspire One 722. Whenever I'm on battery power I get a clicking sound from my hard drive every 5 seconds or so (this does not happen when the laptop is plugged in). I'm dual booting with Windows 7 and I don't get the clicking sound in Windows. The clicking sound stops when I run the command:sudo hdparm -B 254 /dev/sda Also, according to:sudo smartctl -H /dev/sda my hard drive is healthy. Is this clicking sound something I can just ignore? Or is it a serious problem and will it eventually damage my computer? If so, how would I fix it? I have tried adding hdparm -B 254 /dev/sda to my /etc/rc.local file, but I still run into the clicking problem if my computer boots while plugged in and is then unplugged. Also, I'm finding this fix to be unreliable. Sometimes it works, sometimes it does not. Is this a good solution and is there a better way of doing this? Also, would running my laptop with a -B value of 254 have any negative effects? (I read somewhere about a lower level protecting the hard drive from bumps)

    Read the article

  • How do I force the system to look for new sound devices?

    - by John Zeringue
    I have a small flat screen TV (Toshiba) that I often connect via HDMI to my laptop (an HP Pavilion dv4) and use as a computer monitor. When I do this, I prefer to use the TV's speakers, particularly when I'm watching video, because the sound quality is much better. However, when I connect the HDMI cable after turning on my computer (rather than having it plugged in before booting up), Sound Settings does not list the TV as an output device, and I am forced to reboot. I was curious if there is an easier solution to this, perhaps a CLI command to check for new sound outputs. Does anyone know of something like this or have another solution? To clarify, I believe this is a software problem. The HDMI always works, and I can switch my desktop over to the TV at any time. The issue is that, if the HDMI wasn't connected during start up, the TV will not appear as an output option in the Sound Settings GUI. So, unless I'm mistaken, my question is not HDMI specific, but rather a general usage question about manipulating sound settings from the command line.

    Read the article

  • Ubuntu 11.10 very slow compared to Windows

    - by Patrick
    I'm new to Ubuntu/linux. Since my PC is very old and not very fast with Windows 7, I decided to give Ubuntu a try, so I downloaded and installed Ubuntu 11.10 today. When I first started it, I had bad 800x600 resolution and it was very slow and annoying. So I installed a driver for my graphic card and now everything looks very nice (1280x1024).But I think it's still far slower than Windows 7. I tried to run in Ubuntu like a few people suggested on the forum but if I log in I get a black screen saying something like "this video mode cannot be displayed". I get that same screen when booting Ubuntu btw, but after about 15 seconds it disappears and just starts Ubuntu. I also installed other drivers for my graphic card but everything stayed the same. I noticed that i.e. when I open Firefox or system settings it takes about 5 seconds till it opens (while Windows 7 takes under 1 second to start i.e. Chrome) and when I do this my CPU usage gets to 100% for a short time. Computer specs: Memory: 2GB RAM Processor: Intel Pentium 4 2.8GHz Graphics Card: Nvidia GeForce 6800 400MHz. I read on various forums that 11.04 works flawless on many PCs, where 11.10 is very slow. Should I install 11.04 or could anybody help me with this problem?

    Read the article

  • Install Problems on ASUS X401A Notebook

    - by tired_of_trying
    okay... I tried many approaches to install Ubuntu 12.xxx on my new Asus notebook with varying degrees of failure... First: I'm not a newbie but I'm as frustrated as one! Install background: Install from USB DVD drive: The install went well. Re-booted machine. choose ubuntu and it errors with a MBR file error (can't remember the exact wording - something to do with missing the file. Choosing to boot W7 works fine. Install from USB Stick: Couldn't get machine to recognize the .iso Install into Oracle's Vbox: Got the boot splash screen, then hangs with a zillion errors. Note: I didn't have any problems installing ubuntu in Vbox on my iMac and it run's great. Installed using wubi: Installed fine but get errors when booting ubuntu (it doesn't find the needed wubi files). I downloaded to the C: drive and tried installing from there - no luck. For kicks: I tried running Slax Linux .iso from a USB stick and it runs fine. Some Questions: Did I use the correct .iso? (I tried 12.04.0 and 12.04.1 both 32 and 64 bit versions. I simply downloaded them from the download link and didn't use/look for an alternate version. Do I need to do something special when burning the .iso to disc? What? I did read tons of posts but, no luck with finding the solution. Any help is appreciated... thanks

    Read the article

  • Fresh install of 12.04 using USB stick booted into tty1

    - by croc
    I just installed 12.04 Alternate for the first time to give it a try using a USB stick burned with UnetBootIn. It installed without a problem. But it booted into a tty1 console without booting into a GUI. After logging into the tty1 console, I typed unity. It appeared that the system doesn't have unity desktop. How can it be solved? My installation didn't show any error. Something worth mentioning: During installation, I had to choose an option saying 'customize the system to your needs' something like that I don't remember correctly with options 'SSH server','Mail Server', 'Ubuntu Desktop',.....,'Manual selection of packages' etc. I chose 'Ubuntu Desktop'. I haven't encountered something like this in 11.04. To do an installation of Alternate iso using UnetBootIn, i used '12.04_Hdmedia' option of that software and had to change file extension of .ude to .udeb in /pool/main/l/linux that i found in Alternate ubuntu cdrom detect to go around with the cdrom detection problem. I have a 945G intel graphics.

    Read the article

  • Win7 and Ubuntu refuse to coexist

    - by Jeremy
    I'll make this quick: I have an HP laptop with win7, I installed Ubuntu on a separate partition, and when I tried to boot win7 from grub I got the loading screen and no progress-ever. I did a /fixmbr with the windows recovery cd and got back windows, but wiped out grub and my access to Ubuntu. I reinstalled grub from the Ubuntu live usb ( I know I did this correctly) and now windows won't boot, again. I'm a linux noob at a loss. Your wisdom is greatly appreciated! Update in response to Scott Severance: your instructions say to determine the main partition on my computer. I'm not sure what this means... my windows partition is at sda2, my boot partition is at sda1, and my linux root partition is at sda7... Which is the "main" partition? UPDATE: I determined that you were probably referring to the linux root(/) partition, because this was the only partition for which I could follow your instructions without errors. Now, Windows is booting fine (thanks to /fixmbr), but even after the grub instructions there is no grub. It boots straight into windows.

    Read the article

  • Data recovery on a Samsung SV1203N HDD

    - by Jim Conace
    Let me start by saying that I am a beginner in Ubuntu, but pretty knowledgeable with Windows. I am having a strange problem trying to recover data from a Samsung SV1203N HDD (120 GiB). I have tried numerous things in both Windows 7 and Ubuntu 12.04 LTS (on a flash drive, an external HDD and a Live CD). This drive has some very important data on it and I am praying some of you Ubuntu geeks can help me get it back. Here's my problem. The HDD is clicking while I am booting, but it stops when I get into Ubuntu or Windows. It refuses to be detected in the bios, so I cant perform any tests on it. I have tried numerous things in both Windows (repair CD, Jumpers, etc.) and Ubuntu (Boot-Fix, GParted, Testdisk, Photorec, forcing a mount, etc.). But it all seems to lead me back to the fact that the drive is not being recognized in the BIOS. I've even tried chilling the drive in the fridge, which worked well for another drive I work on, and I recovered all of the data in Ubuntu flawlessly. I am assuming that since the drive stops clicking when I get into the OS' that there is hope for recovery. I am going to try an IDE/SATA to USB cable, and replacing the Logic Board, but I want to exhaust all other possibilities before I do that. Any help would be greatly appreciated Bye

    Read the article

  • Can't boot to Windows 7 after installing Ubuntu 11.10

    - by les02jen17
    Here's what happened: I have 2 HDDs. 1st HDD is partitioned like this: C - Windows 7 D* - Empty drive where I installed Ubuntu E - Personal Files F - Personal Files 2nd HDD is partitioned like this: G - Personal Files *the D partition is originally part of the C partition. I resized it (using Easus Partition Master in Windows) and defragged it prior to installing Ubuntu. I installed Ubuntu by booting to the Ubuntu Secure Remix CD, and chose the D partition to install Ubuntu. I did not create a swap drive, and I mounted the / to the D partition. I didnt know where to mount the others, so I just thought by mounting the / to D, it would be okay. After the long installation, upon rebooting, I can't access Windows AND Ubuntu. I get an infinite bootloop and eventually the choices to boot to Safe Modes, Last Known Good Configuration and Start Windows normally. After failing in all of them, I placed the CD back and ran the Boot Repair. I chose the MBR 1st, it didn't work. I then chose the GRUB 2nd and now I was able to boot to the Ubuntu I installed, but not to my Windows 7! I'm using my newly installed Ubuntu while writing this. I hope you can help me. I did the best I could! Here's the link to the boot repair log: http://paste.ubuntu.com/919354/ Thanks in advance!

    Read the article

  • Ubuntu Raring on iMac 2008; graphics update ATI Radeon HD 2600 Pro broke my Raring this morning!

    - by user197406
    Was working on my iMac(2008) 20,5" this morning when again some GLX etc updates appeared! As usual I let the update-installer do it's job; when finished updating, my screen got scrambled; I can not work anymore as the screen shivers, shakes and graphics is one big mess. Ctrl+Alt+F1 does not work either as most of the time my screen is black completely! When booting into OSX 10.8.5 (Raring dual boot with OSX 10.8.5), OSX graphics works flawlessly! Can anybody indicate me which ATI Radeon drivers I can download which repairs the 'malversation' of this mornings updates? I guess I will have to startup with some rescue boot disk (Knoppix?) to do manipulations… As I'm still a noob as well I need clear explanations (please). Raring worked perfectly in dual boot on my iMac until this mornings updates! Needles to say the 'final resort' is restarting (re)installation of Ubuntu Raring, but want to attempt to rescue my present 13.04. Thank you! Kind regards, Gaytan!

    Read the article

  • How to Boot or "enter" into ubnutu 11.04 (Natty Narwhall) on PS3 after installing it?

    - by Xdm
    After failing to install ubuntu 11.04 Desktop version (burned on a dvd, because iso's file size was 726 Mb), in tried the alternate version (about 686 Mb) which i burned into a CD. During the installation process, i manually partitioned the hard drive using ext3. After the installation, the CD ejects itself and i hit "continue". In the k boot prompt i hit "enter" on my the keyboard. I see i welcome message in a dark background (a kind of full screen terminal/console called CLI i think) and was asked to enter my user name and password. After that, instead of booting into the beautiful desktop of Ubuntu, i saw this: ubuntu@my_name$ It was like a line of command i think, where you can use "sudo" commands. It is called a non-graphic mode i think. My my REAL problem is to enter Ubuntu 11.04 with the chocolate-colored background and the African music drum. I tried many commands to boot into the graphic mode of the system such as Ctr+Alt+F7 but nothing happened. In this case, i just saw numbers showing available blocks. I DON'T UNDERSTAND. I also tried startx and sudo startx without result. I DO bought a PS3 BOTH for gaming and for Ubuntu because i can't afford buying a PC. Please help me with my trouble dear Ubuntu 11.04 users. I am counting on you. All the best Xdm

    Read the article

  • How do I get my internal HDD to mount at startup?

    - by el_gallo_azul
    It's either not intuitive or not working in Ubuntu 14.04. I want to mount my internal HDD at at startup (I boot from an SSD). I attempt to set this, following this procedure: Open Disks utility Select the disk Below the disk's Volumes, click on the More actions button Select Edit Mount Options... Select Automatic Mount Options "Off" Under Mount Options, ensure that Mount at startup is selected Click OK Enter password into Authenticate dialog box Restart but this procedure doesn't work. Upon rebooting, and after Grub attempts to start Ubuntu, I receive the error message "An error occurred while mounting /mnt/4f721fc0-8072-453f-b48f-ca686bd89549. Press S to skip mounting or M for manual recovery". That identifier "4f721fc0-8072-453f-b48f-ca686bd89549" was automatically assigned by Ubuntu. I press S and the boot process continues OK. If I try to mount the disk immediately after booting, I receive the error message "Unable to access "Storage"" (I named the volume Storage). So then I start the Disks utility and set it to Automatic Mount Options "On" and reboot. To me, it seems like this should work, but it doesn't. Here are a number of photos of the process (Alt+PrtScn doesn't work after selecting More actions).

    Read the article

  • Mounting a new hard drive (sda1) to my existing filesystem

    - by shank22
    I tried to read some posts regarding mounting a new hard drive, but I am facing some problem. My new hard drive is sda1. The output of sudo fdisk -l is: sudo fdisk -l Disk /dev/sdb: 999.7 GB, 999653638144 bytes 255 heads, 63 sectors/track, 121534 cylinders, total 1952448512 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00016485 Device Boot Start End Blocks Id System /dev/sdb1 * 2048 1935822847 967910400 83 Linux /dev/sdb2 1935824894 1952446463 8310785 5 Extended /dev/sdb5 1935824896 1952446463 8310784 82 Linux swap / Solaris Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x78dbcdc1 Device Boot Start End Blocks Id System /dev/sda1 2048 1953521663 976759808 7 HPFS/NTFS/exFAT What should be done to add this new sda1 hard drive on booting up? What should be added in the /etc/fstab file? I have not performed any partition on the new sda1 drive. I need help on how to proceed from scratch and can't afford to take any risk. Please help!

    Read the article

  • Is this a b43 driver problem?

    - by Nullet
    I have 13.04 on a Dell Inspiron 1564 with Broadcom 4312 WiFi card. The wl drivers cause kernel panic on linux-3.8 so I succesfully installed the b43 driver a couple of months ago. Now I have changed ISP and got a new router, and the connection drop when downloading software from internet to a 2008r2 using Remmina Client, and apt-get install on virtual machines in virtualbox. I have no idea why this suddenly became a problem.. My phone does not loose the connection, just Ubuntu. Output from /var/log/syslog after lost connection rfkill list(after disconnecting): 0: phy0: Wireless LAN Soft blocked: yes Hard blocked: yes I can use NetworkManager to disable wireless and then enable wireless to connect again. rfkill ublock all/wifi/0 removes only Soft blocked. lshw -C network *-network description: Wireless interface physical id: 4 logical name: wlan0 serial: 78:e4:00:78:d2:05 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.8.0-32-generic firmware=478.104 ip=10.0.0.3 link=yes multicast=yes wireless=IEEE lspci 04:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) After waking from suspend and when booting, it takes about 40 sec to get network connection. This has been a problem all along AND a different question, but I mention it anyway.. cus it's annoying! Please take a look and hopefully someone spot a problem! Thanks!

    Read the article

  • Installing Ubuntu on HP Envy 4 - 1104tx (preinstalled Windows 8)

    - by Froyo
    I have been using Linux for more than 2 years now. I had hp pavilion dv4 laptop and Ubuntu 12.04 was working great. I recently purchased HP Envy 4 - 1104tx which has Windows 8 preinstalled. I tried to install Ubuntu 12.04 but since it is not much compatible with UFEI, I downloaded 64 bit iso of ubuntu 12.10. Made a liveUSB using UnetBootin 583. I followed Installing Ubuntu on a Pre-Installed UEFI Supported Windows 8 system but still I am not able to boot with LiveUSB. I disabled secure boot. There is no option for fast boot or anything as such. It still wouldn't work. I also tried booting through Legacy, but I'm unable to install via LiveUSB. Is there any other way? I don't have SSD so no problem of fake raid. Is there some way by which I can install Ubuntu (12.04 preferred)? I don't care about Windows 8. Is there any way via which I can install Ubutnu over Windows 8? (I don't have a CD/DVD ROM).

    Read the article

  • Why does Ubuntu 12.10 Beta2 insist on commiting changes to the partition table?

    - by Uten
    Why does Ubuntu 12.10 Beta2 insist on commiting changes to the partition table even as no real changes has been done? This is a show stopper for me as I'm installing without a CD/DVD ROM. This is how I go about it. I downloaded the iso image and extracted vmlinuz and initrd.lz to the same folder I keep the iso image. Configured grub (0.9x) to boot /ubuntu/vmlinuz with the iso image like this: title ubuntu live-cd kernel /ubuntu/vmlinuz boot=casper iso-scan/filename=/ubuntu/ubuntu-12.10-beta2-desktop-i386.iso ro quiet splash initrd /ubuntu/initrd.lz boot This works well and I get a running livecd session. The iso image is mounted on /isomedia (or something similar). The spare HD space where I want to install Ubuntu is in the logical area (at the wery end of the disk). I have tried both to use the space as empty and preformated with ext4. After selecting the partition and selecting "use as ext4" and selecting a mountpoint (/) I get the message: "The installer needs to commit changes to partition tables, but cannot do so because partitions on the following mount points could not be unmounted" "/isomedia" (or something similar). Is this a "feature" of the installer? To insist that everything is unmounted even if no changes is nescesary (as fare as I understand). It's probably a safety feature but is it needed? I have cahnged layouts with parted and gparted (at the end of the disk) for years without any failures. I understand that booting the iso image like this is not the common way. But it is just such a beautifull way of doing it when you hav a running system and want to play with another. Any one had any success installing Ubuntu (12.10 beta2 ) like this? Best regards Uten

    Read the article

  • Ubuntu 12.04 login screen flickers. “Could not write bytes: broken pipes”

    - by Brayn
    I use Ubuntu 12.04 x64 with a dual-boot setup. Yesterday it worked fine but this morning when I attempted to boot it gets to the login screen and then it just flickers, alternating between the login screen and the console showing boot items (mainly Apache, the last one being "Battery status" although it's a desktop) all with [OK] status. The only error that I can see is: "Could not write bytes: broken pipes" on top of the screen. The only things I can think of that could cause this are: This morning I had a removable hdd plugged in during boot time, which I usually don't have Yesterday I've installed Dwarven Fortress that requires some x32 libraries so I've installed ia32 using synaptic. As far as I know this shouldn't brake the system but I didn't reboot yesterday so I can't be sure. I've tried booting in recovery mode and tried running the utils there but still no luck. I've ran out of ideas. Thanks. EDIT: Forgot to mention that all partitions have plenty of free space EDIT2: In the end I just reinstalled Ubuntu as time was of the essence.

    Read the article

  • Growing your VirtualBox Virtual Disk

    - by Fat Bloke
    Don't you just hate it when this happens: Fortunately, if you're running inside VirtualBox, you can resize your virtual disk and magically make your guest have a bigger disk very easily. There are 2 steps to doing this... 1. Resize the virtual disk Use the VBoxManage command line tool to extend the size of the Virtual Disk, specifying the path to the disk and the size in MB: VBoxManage modifyhd <uuid>|<filename> [--type normal|writethrough|immutable|shareable| readonly|multiattach] [--autoreset on|off] [--compact] [--resize <megabytes>|--resizebyte <bytes>]   If you booted up your guest at this point, the extra space is seen as an unformatted area on the disk, like this: So we now need to tell the guest about the extra space available. 2. Extend the guest's partition to use the extra space How you do this step depends on you guest OS type and the tools you have available. Linux guests often include the excellent gparted partition editor, whereas Windows 7 and 8 provide the Computer Management tool which can resize partitions. Unfortunately, my Windows XP vm has no such tool. But I do have a couple of other options: Most Linux installable .isos include the aforementioned gparted tool, so I could simply attach, say, an Ubuntu.iso as a Virtual CD/DVD in my Windows XP vm and boot off that. Then use gparted to extend the Windows XP partition, before finally rebooting. But I took another route and attached my resized virtual disk to a Windows Server 2012 vm I had lying around. Then I used the Computer Management tool in Windows Server 2012 to extend the partition of the Windows XP disk, before shutting down, unplugging the disk and reattaching to my Windows XP vm. (Note that if your vm's use different disk controllers, Windows will check the disks on booting). When I finally boot up my Windows XP guest I see the available disk space and all is well. At least until the next time - FB 

    Read the article

  • Can't turn off display - 13.10 / iMac

    - by user209883
    I can find no way to completely turn off the display on a late 2013 iMac running 13.10 (Saucy). In the power management settings, I configured the display to "turn off" after one minute to see what would happen. The dimness goes all the way down and everything disappears, BUT the LED backlight remains on. When I try the "xset dpms force off" command, absolutely nothing happens--the command is accepted (no error or warning), but nothing changes. I then wiped everything clean and installed 13.04 (Raring). Both methods (dpms and waiting for sleep) work perfectly there, so something has changed in this new version. The problem can be replicated simply by booting from a bootable USB stick. So, I also gave version 14.04 (Trusty) a try in this manner and it has the exact same issues as 13.10. P.S. I would gladly use 13.04, but the catch there is that I can not get the network card to function. I have spent a week now reading everything i can find on both of these matters with no luck at all. Thank you in advance for any advice.

    Read the article

  • Solaris 11.1: Changes to included FOSS packages

    - by alanc
    Besides the documentation changes I mentioned last time, another place you can see Solaris 11.1 changes before upgrading is in the online package repository, now that the 11.1 packages have been published to http://pkg.oracle.com/solaris/release/, as the “0.175.1.0.0.24.2” branch. (Oracle Solaris Package Versioning explains what each field in that version string means.) When you’re ready to upgrade to the packages from either this repo, or the support repository, you’ll want to first read How to Update to Oracle Solaris 11.1 Using the Image Packaging System by Pete Dennis, as there are a couple issues you will need to be aware of to do that upgrade, several of which are due to changes in the Free and Open Source Software (FOSS) packages included with Solaris, as I’ll explain in a bit. Solaris 11 can update more readily than Solaris 10 In the Solaris 10 and older update models, the way the updates were built constrained what changes we could make in those releases. To change an existing SVR4 package in those releases, we created a Solaris Patch, which applied to a given version of the SVR4 package and replaced, added or deleted files in it. These patches were released via the support websites (originally SunSolve, now My Oracle Support) for applying to existing Solaris 10 installations, and were also merged into the install images for the next Solaris 10 update release. (This Solaris Patches blog post from Gerry Haskins dives deeper into that subject.) Some of the restrictions of this model were that package refactoring, changes to package dependencies, and even just changing the package version number, were difficult to do in this hybrid patch/OS update model. For instance, when Solaris 10 first shipped, it had the Xorg server from X11R6.8. Over the first couple years of update releases we were able to keep it up to date by replacing, adding, & removing files as necessary, taking it all the way up to Xorg server release 1.3 (new version numbering begun after the X11R7 split of the X11 tree into separate modules gave each module its own version). But if you run pkginfo on the SUNWxorg-server package, you’ll see it still displayed a version number of 6.8, confusing users as to which version was actually included. We stopped upgrading the Xorg server releases in Solaris 10 after 1.3, as later versions added new dependencies, such as HAL, D-Bus, and libpciaccess, which were very difficult to manage in this patching model. (We later got libpciaccess to work, but HAL & D-Bus would have been much harder due to the greater dependency tree underneath those.) Similarly, every time the GNOME team looked into upgrading Solaris 10 past GNOME 2.6, they found these constraints made it so difficult it wasn’t worthwhile, and eventually GNOME’s dependencies had changed enough it was completely infeasible. Fortunately, this worked out for both the X11 & GNOME teams, with our management making the business decision to concentrate on the “Nevada” branch for desktop users - first as Solaris Express Desktop Edition, and later as OpenSolaris, so we didn’t have to fight to try to make the package updates fit into these tight constraints. Meanwhile, the team designing the new packaging system for Solaris 11 was seeing us struggle with these problems, and making this much easier to manage for both the development teams and our users was one of their big goals for the IPS design they were working on. Now that we’ve reached the first update release to Solaris 11, we can start to see the fruits of their labors, with more FOSS updates in 11.1 than we had in many Solaris 10 update releases, keeping software more up to date with the upstream communities. Of course, just because we can more easily update now, doesn’t always mean we should or will do so, it just removes the package system limitations from forcing the decision for us. So while we’ve upgraded the X Window System in the 11.1 release from X11R7.6 to 7.7, the Solaris GNOME team decided it was not the right time to try to make the jump from GNOME 2 to GNOME 3, though they did update some individual components of the desktop, especially those with security fixes like Firefox. In other parts of the system, decisions as to what to update were prioritized based on how they affected other projects, or what customer requests we’d gotten for them. So with all that background in place, what packages did we actually update or add between Solaris 11.0 and 11.1? Core OS Functionality One of the FOSS changes with the biggest impact in this release is the upgrade from Grub Legacy (0.97) to Grub 2 (1.99) for the x64 platform boot loader. This is the cause of one of the upgrade quirks, since to go from Solaris 11.0 to 11.1 on x64 systems, you first need to update the Boot Environment tools (such as beadm) to a new version that can handle boot environments that use the Grub2 boot loader. System administrators can find the details they need to know about the new Grub in the Administering the GRand Unified Bootloader chapter of the Booting and Shutting Down Oracle Solaris 11.1 Systems guide. This change was necessary to be able to support new hardware coming into the x64 marketplace, including systems using UEFI firmware or booting off disk drives larger than 2 terabytes. For both platforms, Solaris 11.1 adds rsyslog as an optional alternative to the traditional syslogd, and OpenSCAP for checking security configuration settings are compliant with site policies. Note that the support repo actually has newer versions of BIND & fetchmail than the 11.1 release, as some late breaking critical fixes came through from the community upstream releases after the Solaris 11.1 release was frozen, and made their way to the support repository. These are responsible for the other big upgrade quirk in this release, in which to upgrade a system which already installed those versions from the support repo, you need to either wait for those packages to make their way to the 11.1 branch of the support repo, or follow the steps in the aforementioned upgrade walkthrough to let the package system know it's okay to temporarily downgrade those. Developer Stack While Solaris 11.0 included Python 2.7, many of the bundled python modules weren’t packaged for it yet, limiting its usability. For 11.1, many more of the python modules include 2.7 versions (enough that I filtered them out of the below table, but you can always search on the package repository server for them. For other language runtimes and development tools, 11.1 expands the use of IPS mediated links to choose which version of a package is the default when the packages are designed to allow multiple versions to install side by side. For instance, in Solaris 11.0, GNU automake 1.9 and 1.10 were provided, and developers had to run them as either automake-1.9 or automake-1.10. In Solaris 11.1, when automake 1.11 was added, also added was a /usr/bin/automake mediated link, which points to the automake-1.11 program by default, but can be changed to another version by running the pkg set-mediator command. Mediated links were also used for the Java runtime & development kits in 11.1, changing the default versions to the Java 7 releases (the 1.7.0.x package versions), while allowing admins to switch links such as /usr/bin/javac back to Java 6 if they need to for their site, to deal with Java 7 compatibility or other issues, without having to update each usage to use the full versioned /usr/jdk/jdk1.6.0_35/bin/javac paths for every invocation. Desktop Stack As I mentioned before, we upgraded from X11R7.6 to X11R7.7, since a pleasant coincidence made the X.Org release dates line up nicely with our feature & code freeze dates for this release. (Or perhaps it wasn’t so coincidental, after all, one of the benefits of being the person making the release is being able to decide what schedule is most convenient for you, and this one worked well for me.) For the table below, I’ve skipped listing the packages in which we use the X11 “katamari” version for the Solaris package version (mainly packages combining elements of multiple upstream modules with independent version numbers), since they just all changed from 7.6 to 7.7. In the graphics drivers, we worked with Intel to update the Intel Integrated Graphics Processor support to support 3D graphics and kernel mode setting on the Ivy Bridge chipsets, and updated Nvidia’s non-FOSS graphics driver from 280.13 to 295.20. Higher up in the desktop stack, PulseAudio was added for audio support, and liblouis for Braille support, and the GNOME applications were built to use them. The Mozilla applications, Firefox & Thunderbird moved to the current Extended Support Release (ESR) versions, 10.x for each, to bring up-to-date security fixes without having to be on Mozilla’s agressive 6 week feature cycle release train. Detailed list of changes This table shows most of the changes to the FOSS packages between Solaris 11.0 and 11.1. As noted above, some were excluded for clarity, or to reduce noise and duplication. All the FOSS packages which didn't change the version number in their packaging info are not included, even if they had updates to fix bugs, security holes, or add support for new hardware or new features of Solaris. Package11.011.1 archiver/unrar 3.8.5 4.1.4 audio/sox 14.3.0 14.3.2 backup/rdiff-backup 1.2.1 1.3.3 communication/im/pidgin 2.10.0 2.10.5 compress/gzip 1.3.5 1.4 compress/xz not included 5.0.1 database/sqlite-3 3.7.6.3 3.7.11 desktop/remote-desktop/tigervnc 1.0.90 1.1.0 desktop/window-manager/xcompmgr 1.1.5 1.1.6 desktop/xscreensaver 5.12 5.15 developer/build/autoconf 2.63 2.68 developer/build/autoconf/xorg-macros 1.15.0 1.17 developer/build/automake-111 not included 1.11.2 developer/build/cmake 2.6.2 2.8.6 developer/build/gnu-make 3.81 3.82 developer/build/imake 1.0.4 1.0.5 developer/build/libtool 1.5.22 2.4.2 developer/build/makedepend 1.0.3 1.0.4 developer/documentation-tool/doxygen 1.5.7.1 1.7.6.1 developer/gnu-binutils 2.19 2.21.1 developer/java/jdepend not included 2.9 developer/java/jdk-6 1.6.0.26 1.6.0.35 developer/java/jdk-7 1.7.0.0 1.7.0.7 developer/java/jpackage-utils not included 1.7.5 developer/java/junit 4.5 4.10 developer/lexer/jflex not included 1.4.1 developer/parser/byaccj not included 1.14 developer/parser/java_cup not included 0.10 developer/quilt 0.47 0.60 developer/versioning/git 1.7.3.2 1.7.9.2 developer/versioning/mercurial 1.8.4 2.2.1 developer/versioning/subversion 1.6.16 1.7.5 diagnostic/constype 1.0.3 1.0.4 diagnostic/nmap 5.21 5.51 diagnostic/scanpci 0.12.1 0.13.1 diagnostic/wireshark 1.4.8 1.8.2 diagnostic/xload 1.1.0 1.1.1 editor/gnu-emacs 23.1 23.4 editor/vim 7.3.254 7.3.600 file/lndir 1.0.2 1.0.3 image/editor/bitmap 1.0.5 1.0.6 image/gnuplot 4.4.0 4.6.0 image/library/libexif 0.6.19 0.6.21 image/library/libpng 1.4.8 1.4.11 image/library/librsvg 2.26.3 2.34.1 image/xcursorgen 1.0.4 1.0.5 library/audio/pulseaudio not included 1.1 library/cacao 2.3.0.0 2.3.1.0 library/expat 2.0.1 2.1.0 library/gc 7.1 7.2 library/graphics/pixman 0.22.0 0.24.4 library/guile 1.8.4 1.8.6 library/java/javadb 10.5.3.0 10.6.2.1 library/java/subversion 1.6.16 1.7.5 library/json-c not included 0.9 library/libedit not included 3.0 library/libee not included 0.3.2 library/libestr not included 0.1.2 library/libevent 1.3.5 1.4.14.2 library/liblouis not included 2.1.1 library/liblouisxml not included 2.1.0 library/libtecla 1.6.0 1.6.1 library/libtool/libltdl 1.5.22 2.4.2 library/nspr 4.8.8 4.8.9 library/openldap 2.4.25 2.4.30 library/pcre 7.8 8.21 library/perl-5/subversion 1.6.16 1.7.5 library/python-2/jsonrpclib not included 0.1.3 library/python-2/lxml 2.1.2 2.3.3 library/python-2/nose not included 1.1.2 library/python-2/pyopenssl not included 0.11 library/python-2/subversion 1.6.16 1.7.5 library/python-2/tkinter-26 2.6.4 2.6.8 library/python-2/tkinter-27 2.7.1 2.7.3 library/security/nss 4.12.10 4.13.1 library/security/openssl 1.0.0.5 (1.0.0e) 1.0.0.10 (1.0.0j) mail/thunderbird 6.0 10.0.6 network/dns/bind 9.6.3.4.3 9.6.3.7.2 package/pkgbuild not included 1.3.104 print/filter/enscript not included 1.6.4 print/filter/gutenprint 5.2.4 5.2.7 print/lp/filter/foomatic-rip 3.0.2 4.0.15 runtime/java/jre-6 1.6.0.26 1.6.0.35 runtime/java/jre-7 1.7.0.0 1.7.0.7 runtime/perl-512 5.12.3 5.12.4 runtime/python-26 2.6.4 2.6.8 runtime/python-27 2.7.1 2.7.3 runtime/ruby-18 1.8.7.334 1.8.7.357 runtime/tcl-8/tcl-sqlite-3 3.7.6.3 3.7.11 security/compliance/openscap not included 0.8.1 security/nss-utilities 4.12.10 4.13.1 security/sudo 1.8.1.2 1.8.4.5 service/network/dhcp/isc-dhcp 4.1 4.1.0.6 service/network/dns/bind 9.6.3.4.3 9.6.3.7.2 service/network/ftp (ProFTPD) 1.3.3.0.5 1.3.3.0.7 service/network/samba 3.5.10 3.6.6 shell/conflict 0.2004.9.1 0.2010.6.27 shell/pipe-viewer 1.1.4 1.2.0 shell/zsh 4.3.12 4.3.17 system/boot/grub 0.97 1.99 system/font/truetype/liberation 1.4 1.7.2 system/library/freetype-2 2.4.6 2.4.9 system/library/libnet 1.1.2.1 1.1.5 system/management/cim/pegasus 2.9.1 2.11.0 system/management/ipmitool 1.8.10 1.8.11 system/management/wbem/wbemcli 1.3.7 1.3.9.1 system/network/routing/quagga 0.99.8 0.99.19 system/rsyslog not included 6.2.0 terminal/luit 1.1.0 1.1.1 text/convmv 1.14 1.15 text/gawk 3.1.5 3.1.8 text/gnu-grep 2.5.4 2.10 web/browser/firefox 6.0.2 10.0.6 web/browser/links 1.0 1.0.3 web/java-servlet/tomcat 6.0.33 6.0.35 web/php-53 not included 5.3.14 web/php-53/extension/php-apc not included 3.1.9 web/php-53/extension/php-idn not included 0.2.0 web/php-53/extension/php-memcache not included 3.0.6 web/php-53/extension/php-mysql not included 5.3.14 web/php-53/extension/php-pear not included 5.3.14 web/php-53/extension/php-suhosin not included 0.9.33 web/php-53/extension/php-tcpwrap not included 1.1.3 web/php-53/extension/php-xdebug not included 2.2.0 web/php-common not included 11.1 web/proxy/squid 3.1.8 3.1.18 web/server/apache-22 2.2.20 2.2.22 web/server/apache-22/module/apache-sed 2.2.20 2.2.22 web/server/apache-22/module/apache-wsgi not included 3.3 x11/diagnostic/xev 1.1.0 1.2.0 x11/diagnostic/xscope 1.3 1.3.1 x11/documentation/xorg-docs 1.6 1.7 x11/keyboard/xkbcomp 1.2.3 1.2.4 x11/library/libdmx 1.1.1 1.1.2 x11/library/libdrm 2.4.25 2.4.32 x11/library/libfontenc 1.1.0 1.1.1 x11/library/libfs 1.0.3 1.0.4 x11/library/libice 1.0.7 1.0.8 x11/library/libsm 1.2.0 1.2.1 x11/library/libx11 1.4.4 1.5.0 x11/library/libxau 1.0.6 1.0.7 x11/library/libxcb 1.7 1.8.1 x11/library/libxcursor 1.1.12 1.1.13 x11/library/libxdmcp 1.1.0 1.1.1 x11/library/libxext 1.3.0 1.3.1 x11/library/libxfixes 4.0.5 5.0 x11/library/libxfont 1.4.4 1.4.5 x11/library/libxft 2.2.0 2.3.1 x11/library/libxi 1.4.3 1.6.1 x11/library/libxinerama 1.1.1 1.1.2 x11/library/libxkbfile 1.0.7 1.0.8 x11/library/libxmu 1.1.0 1.1.1 x11/library/libxmuu 1.1.0 1.1.1 x11/library/libxpm 3.5.9 3.5.10 x11/library/libxrender 0.9.6 0.9.7 x11/library/libxres 1.0.5 1.0.6 x11/library/libxscrnsaver 1.2.1 1.2.2 x11/library/libxtst 1.2.0 1.2.1 x11/library/libxv 1.0.6 1.0.7 x11/library/libxvmc 1.0.6 1.0.7 x11/library/libxxf86vm 1.1.1 1.1.2 x11/library/mesa 7.10.2 7.11.2 x11/library/toolkit/libxaw7 1.0.9 1.0.11 x11/library/toolkit/libxt 1.0.9 1.1.3 x11/library/xtrans 1.2.6 1.2.7 x11/oclock 1.0.2 1.0.3 x11/server/xdmx 1.10.3 1.12.2 x11/server/xephyr 1.10.3 1.12.2 x11/server/xorg 1.10.3 1.12.2 x11/server/xorg/driver/xorg-input-keyboard 1.6.0 1.6.1 x11/server/xorg/driver/xorg-input-mouse 1.7.1 1.7.2 x11/server/xorg/driver/xorg-input-synaptics 1.4.1 1.6.2 x11/server/xorg/driver/xorg-input-vmmouse 12.7.0 12.8.0 x11/server/xorg/driver/xorg-video-ast 0.91.10 0.93.10 x11/server/xorg/driver/xorg-video-ati 6.14.1 6.14.4 x11/server/xorg/driver/xorg-video-cirrus 1.3.2 1.4.0 x11/server/xorg/driver/xorg-video-dummy 0.3.4 0.3.5 x11/server/xorg/driver/xorg-video-intel 2.10.0 2.18.0 x11/server/xorg/driver/xorg-video-mach64 6.9.0 6.9.1 x11/server/xorg/driver/xorg-video-mga 1.4.13 1.5.0 x11/server/xorg/driver/xorg-video-openchrome 0.2.904 0.2.905 x11/server/xorg/driver/xorg-video-r128 6.8.1 6.8.2 x11/server/xorg/driver/xorg-video-trident 1.3.4 1.3.5 x11/server/xorg/driver/xorg-video-vesa 2.3.0 2.3.1 x11/server/xorg/driver/xorg-video-vmware 11.0.3 12.0.2 x11/server/xserver-common 1.10.3 1.12.2 x11/server/xvfb 1.10.3 1.12.2 x11/server/xvnc 1.0.90 1.1.0 x11/session/sessreg 1.0.6 1.0.7 x11/session/xauth 1.0.6 1.0.7 x11/session/xinit 1.3.1 1.3.2 x11/transset 0.9.1 1.0.0 x11/trusted/trusted-xorg 1.10.3 1.12.2 x11/x11-window-dump 1.0.4 1.0.5 x11/xclipboard 1.1.1 1.1.2 x11/xclock 1.0.5 1.0.6 x11/xfd 1.1.0 1.1.1 x11/xfontsel 1.0.3 1.0.4 x11/xfs 1.1.1 1.1.2 P.S. To get the version numbers for this table, I ran a quick perl script over the output from: % pkg contents -H -r -t depend -a type=incorporate -o fmri \ `pkg contents -H -r -t depend -a type=incorporate -o fmri [email protected],5.11-0.175.1.0.0.24` \ | sort /tmp/11.1 % pkg contents -H -r -t depend -a type=incorporate -o fmri \ `pkg contents -H -r -t depend -a type=incorporate -o fmri [email protected],5.11-0.175.0.0.0.2` \ | sort /tmp/11.0

    Read the article

< Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >