Search Results

Search found 2403 results on 97 pages for 'snatch 02'.

Page 62/97 | < Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >

• Ubuntu 12.10 Trackpoint not detected Thinkpad X130e

  - by killerknives

  I just did a fresh install of 12.10 and now only my touchpad works. The trackpoint and Left/Right buttons below the trackpoint do not work. The trackpoint worked fine as of 12.04. I've searched online and there was a hack that said that disabling the touchpad would enable the trackpoint. WRONG! You'll end up having to use the keyboard =/. I don't know what is needed so I'll just dump some stuff. lspci: 00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Complex 00:01.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Wrestler [Radeon HD 6310] 00:01.1 Audio device: Advanced Micro Devices [AMD] nee ATI Wrestler HDMI Audio [Radeon HD 6250/6310] 00:05.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:06.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:07.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 42) 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge (rev 40) 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 0 (rev 43) 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 1 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 2 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 3 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 4 00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 6 00:18.6 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 5 00:18.7 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 7 01:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) 02:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0) I've installged gpointing-device-setting and it only lists the touchpad. No trackpoint. What should I do? What data do you need?

  Read the article

• Neo4J and Azure and VS2012 and Windows 8

  - by Chris Skardon

  Now, I know that this has been written about, but both of the main places (http://www.richard-banks.org/2011/02/running-neo4j-on-azure.html and http://blog.neo4j.org/2011/02/announcing-neo4j-on-windows-azure.html) utilise VS2010, and well, I’m on VS2012 and Windows 8. Not that I think Win 8 had anything to do with it really, anyhews! I’m going to begin from the beginning, this is my first foray into running something on Azure, so it’s been a bit of a learning curve. But luckily the Neo4J guys have got us started, so let’s download the VS2010 solution: http://neo4j.org/get?file=Neo4j.Azure.Server.zip OK, the other thing we’ll need is the VS2012 Azure SDK, so let’s get that as well: http://www.windowsazure.com/en-us/develop/downloads/ (I just did the full install). Now, unzip the VS2010 solution and let’s open it in VS2012: <your location>\Neo4j.Azure.Server\Neo4j.Azure.Server.sln One-way-upgrade? Yer! Ignore the migration report – we don’t care! Let’s build that sucker… Ahhh 14 errors… WindowsAzure does not exist in the namespace ‘Microsoft’ Not a problem right? We’ve installed the SDK, just need to update the references: We can ignore the Test projects, they don’t use Azure, we’re interested in the other projects, so what we’ll do is remove the broken references, and add the correct ones, so expand the references bit of each project: hunt out those yellow exclamation marks, and delete them! You’ll need to add the right ones back in (listed below), when you go to the ‘Add Reference’ dialog make sure you have ‘Assemblies’ and ‘Framework’ selected before you seach (and search for ‘microsoft.win’ to narrow it down) So the references you need for each project are: CollectDiagnosticsData Microsoft.WindowsAzure.Diagnostics Microsoft.WindowsAzure.StorageClient Diversify.WindowsAzure.ServiceRuntime Microsoft.WindowsAzure.CloudDrive Microsoft.WindowsAzure.ServiceRuntime Microsoft.WindowsAzure.StorageClient Right, so let’s build again… Sweet! No errors.   Now we need to setup our Blobs, I’m assuming you are using the most up-to-date Java you happened to have downloaded :) in my case that’s JRE7, and that is located in: C:\Program Files (x86)\Java\jre7 So, zip up that folder into whatever you want to call it, I went with jre7.zip, and stuck it in a temp folder for now. In that same temp folder I also copied the neo4j zip I was using: neo4j-community-1.7.2-windows.zip OK, now, we need to get these into our Blob storage, this is where a lot of stuff becomes unstuck - I didn’t find any applications that helped me use the blob storage, one would crash (because my internet speed is so slow) and the other just didn’t work – sure it looked like it had worked, but when push came to shove it didn’t. So this is how I got my files into Blob (local first): 1. Run the ‘Storage Emulator’ (just search for that in the start menu) 2. That takes a little while to start up so fire up another instance of Visual Studio in the mean time, and create a new Console Application. 3. Manage Nuget Packages for that solution and add ‘Windows Azure Storage’ Now you’re set up to add the code: public static void Main() { CloudStorageAccount cloudStorageAccount = CloudStorageAccount.DevelopmentStorageAccount; CloudBlobClient client = cloudStorageAccount.CreateCloudBlobClient(); client.Timeout = TimeSpan.FromMinutes(30); CloudBlobContainer container = client.GetContainerReference("neo4j"); //This will create it as well   UploadBlob(container, "jre7.zip", "c:\\temp\\jre7.zip"); UploadBlob(container, "neo4j-community-1.7.2-windows.zip", "c:\\temp\\neo4j-community-1.7.2-windows.zip"); }   private static void UploadBlob(CloudBlobContainer container, string blobName, string filename) { CloudBlob blob = container.GetBlobReference(blobName);   using (FileStream fileStream = File.OpenRead(filename)) blob.UploadFromStream(fileStream); } This will upload the files to your local storage account (to switch to an Azure one, you’ll need to create a storage account, and use those credentials when you make your CloudStorageAccount above) To test you’ve got them uploaded correctly, go to: http://localhost:10000/devstoreaccount1/neo4j/jre7.zip and you will hopefully download the zip file you just uploaded. Now that those files are there, we are ready for some final configuration… Right click on the Neo4jServerHost role in the Neo4j.Azure.Server cloud project: Click on the ‘Settings’ tab and we’ll need to do some changes – by default, the 1.7.2 edition of neo4J unzips to: neo4j-community-1.7.2 So, we need to update all the ‘neo4j-1.3.M02’ directories to be ‘neo4j-community-1.7.2’, we also need to update the Java runtime location, so we start with this: and end with this: Now, I also changed the Endpoints settings, to be HTTP (from TCP) and to have a port of 7410 (mainly because that’s straight down on the numpad) The last ‘gotcha’ is some hard coded consts, which had me looking for ages, they are in the ‘ConfigSettings’ class of the ‘Neo4jServerHost’ project, and the ones we’re interested in are: Neo4jFileName JavaZipFileName Change those both to what that should be. OK Nearly there (I promise)! Run the ‘Compute Emulator’ (same deal with the Start menu), in your system tray you should have an Azure icon, when the compute emulator is up and running, right click on the icon and select ‘Show Compute Emulator UI’ The last steps! Make sure the ‘Neo4j.Azure.Server’ cloud project is set up as the start project and let’s hit F5 tension mounts, the build takes place (you need to accept the UAC warning) and VS does it’s stuff. If you look at the Compute Emulator UI you’ll see some log stuff (which you’ll need if this goes awry – but it won’t don’t worry!) In a bit, the console and a Java window will pop up: Then the console will bog off, leaving just the Java one, and if we switch back to the Compute Emulator UI and scroll up we should be able to see a line telling us the port number we’ve been assigned (in my case 7411): (If you can’t see it, don’t worry.. press CTRL+A on the emulator, then CTRL+C, copy all the text and paste it into something like Notepad, then just do a Find for ‘port’ you’ll soon see it) Go to your favourite browser, and head to: http://localhost:YOURPORT/ and you should see the WebAdmin! See you on the cloud side hopefully! Chris PS Other gotchas! OK, I’ve been caught out a couple of times: I had an instance of Neo4J running as a service on my machine, the Azure instance wanted to run the https version of the server on the same port as the Service was running on, and so Java would complain that the port was already in use.. The first time I converted the project, it didn’t update the version of the Azure library to load, in the App.Config of the Neo4jServerHost project, and VS would throw an exception saying it couldn’t find the Azure dll version 1.0.0.0.

  Read the article

• Display Driver Issue on an hp TX2-1160ea Notebook

  - by Sam

  I'm new to Linux and recently switched to Ubuntu 11.04 due to my project requirement. My laptop has been freezing and going to black screen of death when I run anything related to display (Share desktop, stream video, etc). Today I went through the Ubuntu forum to install the appropriate graphic driver and, after doing it, I rebooted my PC. It gave an error before login saying "select the recovery mode" and after clicking OK, it didn't give the same error on reboot but I've lost the 11.04 graphical interface and all I see is the interface of Ubuntu v10 with slow visuals (even scrolling up/down on browser is really slow). For the reference, here's a desktop screenshot so that you can understand the situation. Also the laptop is overheating. How can I fix this problem? How can i get the Ubuntu 11.04 view back? I also tried Google, but couldn't find any issue like this. Some general Information: Laptop: HP TouchSmart TX2-1160ea Processor: AMD Turion TX2 Memory: 4GB OS: Ubuntu 11.04 Some debugging information:: $ report-hw | grep controller lspci -knn: 00:11.0 SATA controller [0106]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] lspci -knn: 00:14.3 ISA bridge [0601]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d] lspci -knn: 01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RS780M/RS780MN [Radeon HD 3200 Graphics] [1002:9612] lspci -knn: 08:00.0 Network controller [0280]: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] (rev 01) lspci -knn: 09:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02) And: $ dpkg -l '*fglrx*' Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Conf-files/Unpacked/halF-conf/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad) ||/ Name Version Description +++-==============-==============-============================================ ii fglrx 2:8.840-0ubunt Video driver for the ATI graphics accelerato ii fglrx-amdcccle 2:8.840-0ubunt Catalyst Control Center for the ATI graphics un fglrx-control <none> (no description available) un fglrx-control- <none> (no description available) ii fglrx-dev 2:8.840-0ubunt Video driver for the ATI graphics accelerato un fglrx-driver <none> (no description available) un fglrx-driver-d <none> (no description available) un fglrx-kernel-s <none> (no description available) un fglrx-modalias <none> (no description available) un xfree86-driver <none> (no description available) un xfree86-driver <none> (no description available) un xorg-driver-fg <none> (no description available) un xorg-driver-fg <none> (no description available) If you need any more information that could help, just ask.

  Read the article

• What is the Endeca MDEX Engine?

  - by Grant Schofield

  Today I would like to draw your attention to a really helpful article by Rittmanmead taking a deeper look under the covers at the Endeca MDEX engine; how it works, what's so different about it, and why that matters to customers. This will in particular be useful for the technical audience. The other articles in the Endeca Week series are equally useful for a wider audience. http://www.rittmanmead.com/2012/02/oracle-endeca-week-what-is-the-endeca-mdex-engine/

  Read the article

• Ubuntu Dual Screen Using Virtual Machine - AMD GPU

  - by Chris

  I've been searching online and reading tutorials and etc about how to make my ubuntu VM dual screen(x86_64). I have first tried to run these commands: sudo aticonfig --initial -f which gave me the ouput of: sudo: aitconfig: command not found I then googled the output and followed these instructions that I tells me to install my ATI drivers onto my ubuntu. wget http://www2.ati.com/drivers/linux/ati-driver-installer-11-5-x86.x86_64.run sudo sh ati-driver-installer-11-5-x86.x86_64.run --buildpkg Ubuntu/natty sudo dpkg -i *.deb sudo apt-get -f install sudo aticonfig -f --initial --adapter=all sudo reboot It all works well until I input sudo apt-get -f install which gives me the following output: sudo apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 25 not upgraded. 3 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Setting up fglrx (2:8.850-0ubuntu1) ... update-alternatives: error: alternative link /usr/bin/aticonfig is already managed by x86_64-linux-gnu_gl_conf. dpkg: error processing fglrx (--configure): subprocess installed post-installation script returned error exit status 2 dpkg: dependency problems prevent configuration of fglrx-amdcccle: fglrx-amdcccle depends on fglrx; however: Package fglrx is not configured yet. dpkg: error processing fglrx-amdcccle (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of fglrx-dev: fglrx-dev depends on fglrx; however: Package fglrx is not configured yet. dpkg: error processing fglrx-dev (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: fglrx fglrx-amdcccle fglrx-dev E: Sub-process /usr/bin/dpkg returned an error code (1) At this point, I don't know what to do since running: gksudo amdcccle For the record, I have 3D acceleration turned on. The following is my GPU for my VM lspci | grep VGA 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter Any Help on how I can make my VM dual screen with Ubuntu would be great. Thank you in advance.

  Read the article

• Why am I getting a "network is unreachable" error on Ubuntu Server?

  - by jason328

  I'm a completely new to Ubuntu server and am having a hard time connecting the server to the internet. I first ran ping -n 8.8.8.8 connect:Network is unreachable Then I ran ifconfig Link encap:Local Loopback inet addr:127.0.0.1 Mask 255.0.0.0 inet6 addr: ::1/28Scope:host UP LOOPBACK RUNNING MTU:16436 RX packets:192 errors:0 dropped:0 overruns:0 frame:0 TX packets:192 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:15360 (15.2KB) TX bytes:15360 (15.3KB) Here is ouput for sudo lspci -n 00:00.0 0600: 8086:2580 (rev 04) 00:02.0 0300: 8086:2582 (rev 04) 00:1d.0 0c03: 8086:2658 (rev 03) 00:1d.1 0c03: 8086:2659 (rev 03) 00:1d.0 0c03: 8086:265a (rev 03) 00:1d.0 0c03: 8086:265b (rev 03) 00:1d.0 0c03: 8086:265c (rev 03) 00:1e.0 0604: 8086:244e (rev d3) 00:1e.0 0401: 8086:266e (rev 03) 00:1f.0 0601: 8086:2640 (rev 03) 00:1f.0 0101: 8086:2651 (rev 03) 00:1f.0 0c05: 8086:266a (rev 03) 00:0b.0 0200: 8086:1654 (rev 03) lshw-c network returns WARNING: you should run this program as super-user. *-network DISABLED description:Ethernet interface product: NetXtreme BCM5705_2 Gigabit Ethernet vender: Broadcom Corporation physical id:b bus info:pci@0000:0a:0b.0 logical name: eth0 capabilities: bus_master_cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion= 3.121 firmware=5705-v3.18 latency=32 mingnt=64 multicast=yes port=twister pair lsmod code returned this Module Size Used By e100 37213 0 dm_crypt 23125 1 ppdev 17113 0 psmouse 87603 0 snd_intel8x0 38570 0 snd_ac97_codec 134826 1 snd_intel8x0 ac97_bus 12730 1 snd_ac97_codec snd_pcm 97188 2 snd_intel8x0, snd_ac97_codec serio_raw 13211 0 snd_timer 29990 1 snd_pcm snd 78855 4 snd_intel8x0, snd_ac97_codec, snd_pcm,snd_timer soundcore 15091 1 snd snd_page_alloc 18529 2 snd_intel8x0, snd_pcm ext2 73795 1 parport_pc 32866 1 mac_hid 13253 0 lp 17799 0 parport 46562 3 ppdev, parport_pc,lp usbhid 47199 0 hid 99559 1 usbhid tg3 152032 0 i915 468651 1 floppy 70365 0 drm_kms_helper 46978 1 i915 drm 242038 2 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 video 19596 1 i915 Again there is more but it's giving info on the driver itself. I know it works, I've used it. I assume then that my network got disabled when I installed Ubuntu Server. How do I enable it? I checked and the internet cable is connected to the D-link router. I have also used this same computer for internet access when I had Ubuntu Desktop installed so internet does work.

  Read the article

• StreamInsight is in all editions (except express)

  - by simonsabin

  Contrary to many posts and even press releases from Microsoft StreamInsight is not just for Data Center edition. It is available in all paid for editions. If you read the license terms http://go.microsoft.com/fwlink/?LinkID=186261&clcid=0x409 you will see you get StreamInsight in all paid editions. Whats confusing is the performance/limitations in each edition. The only reference I could find of these limitations is here http://blogs.msdn.com/b/streaminsight/archive/2010/02/10/streaminsight-versions...(read more)

  Read the article

• ArchBeat Link-o-Rama for 2012-04-05

  - by Bob Rhubart

  Webcast: Oracle Maximum Availability Architecture Best Practices event.on24.com Date: Thursday, April 12, 2012 Time: 10:00 AM PDT Oracle expert Tom Kyte discusses how Oracle’s Maximum Availability Architecture can help to minimize the costs and risk of downtime. Oracle Enterprise Manager Ops Center 12c Launch - Interactive Webcast and Live Chat www.oracle.com Thursday, April 12, 2012. 9 a.m. PT / 12 p.m. ET / 4 p.m. GMT. Speakers: Steve Wilson (VP Systems Management, Oracle) John Fowler (Exec VP Systems, Oracle) Brad Cameron (VP Development, Oracle Fusion Middleware) Bill Nesheim (VP Oracle Solaris) Dennis Reno (VP Customer Portal Experience, Oracle) Mike Wookey (Chief Architect, Oracle Enterprise Manager Ops Center) Prasad Pai (Sr Director, Oracle Enterprise Manager Ops Center) 2012 Real World Performance Tour Dates |Performance Tuning | Performance Engineering www.ioug.org Coming to your town: a full day of real world database performance with Tom Kyte, Andrew Holdsworth, and Graham Wood. Rochester, NY - March 8 Los Angeles, CA - April 30 Orange County, CA - May 1 Redwood Shores, CA - May 3 Oracle Technology Network Developer Day: MySQL - New York www.oracle.com Wednesday, May 02, 2012 8:00 AM – 4:30 PM Grand Hyatt New York 109 East 42nd Street, Grand Central Terminal New York, NY 10017 Webcast Series: Data Warehousing Best Practices event.on24.com April 19, 2012 - Best Practices for Workload Management of a Data Warehouse on Oracle Exadata May 10, 2012 - Best Practices for Extreme Data Warehouse Performance on Oracle Exadata How to create a Global Rule that stores a document’s folder path in a custom metadata field | Nicolas Montoya blogs.oracle.com An illustrated how-to from Oracle Fusion Middleware A-Team blogger Nicolas Montoya. Get Proactive with Fusion Middleware | Daniel Mortimer blogs.oracle.com Daniel Mortimer shows how to access "a one stop shop for navigating to proactive support material, tools, and communication channels related to Oracle Fusion Middleware." Build an enterprise on 'other peoples' work', via SOA and cloud | Joe McKendrick www.zdnet.com Are you down with OPW? Joe McKendrick's synopsis of a recent presentation by David Linthicum focuses on reuse. Oracle Fusion Middleware Security: Unsolicited login with OAM 11g | Chris Johnson fusionsecurity.blogspot.com Chris Johnson shows how to create a shopping cart login model using "plain old HTML." How to use the Human WorkFlow Web Services | Edwin Biemond biemond.blogspot.com Oracle ACE Edwin Biemond shows how to invoke two WorkFlow web services to query the Human task in Oracle SOA Suite with your own ordering and restrictions. Bad Practice Use Case for LOV Performance Implementation in ADF BC | Andrejus Baranovskis andrejusb.blogspot.com "If you want to learn something well, there is nothing better [than] to learn bad practices first," says Oracle ACE Director Andrejus Baranovskis. Thought for the Day "The best meetings get real work done. When your people learn that your meetings actually accomplish something, they will stop making excuses to be elsewhere." — Larry Constantine

  Read the article

• APress Deal of the Day 2/June/2014 - Pro SQL Server 2012 Integration Services

  - by TATWORTH

  Originally posted on: http://geekswithblogs.net/TATWORTH/archive/2014/06/02/apress-deal-of-the-day-2june2014---pro-sql-server.aspxToday’s $10 Deal of the Day from APress at http://www.apress.com/9781430236924 is Pro SQL Server 2012 Integration Services. “Pro SQL Server 2012 Integration Services is your key to building powerful extract, transform, load (ETL) solutions using SQL Server 2012 Integration Services (SSIS).”

  Read the article

• Atheros AR928X wireless connection makes neighbourhood machine drop off line

  - by funicorn

  I have an Acer laptop with Atheros AR928X wireless card installed, supported by ath9k driver in the linux kernel. There are other 5 computers sharing wireless connection via a TPLink 150Mbit/s wireless router. At first I found the network is a little bit slower than it's in Windows7, which I accepted as it should be. However a very strange thing is, each time I connected to the router and downloaded stuff for a while, one of the computers running Windows7 in my local network dropped off from the router. And if I run my laptop under Windows7, everything is fine. What's even stranger is although the network becomes slower, only the certain computer drops and totally freezes in connection with the router. I'm not willing to conclude it's due to the unhealthy connection from my laptop to the router, however we have confirmed this for more than one times and there is no problem with the network when I'm running WIndows7. I'm extremely confused about what's going on. As a Linux user running Ubuntu over 5 years, I am awared that wireless driver in Linux is badly notorious of lack of stability and slow speed. But is it so bad that the unhealthy wireless connection can do damage to another computer in the same local network? I do see a lot of "Tx excessive retries" in iwconfig output. But how exactly does this happen ? Thanks for your help. I guess I have to use this answer box to show the outputs $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=47/70 Signal level=-63 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:2 Invalid misc:23 Missed beacon:0 To show what's wrong with the wireless connection, I ran iwconfig again within 3 minutes, during which time I hardly did anything and the network was not much busy than being nearly idle $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:9 Invalid misc:28 Missed beacon:0 You can see Tx excessive retires and Invalid misc increase very quickly. $ sudo iwlist wlan0 modu wlan0 unknown modulation information. $ sudo iwlist wlan0 channel wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz Current Frequency:2.427 GHz (Channel 4)

  Read the article

• How do I connect Ubuntu to Sony Bravia LED TV via HDMI?

  - by VedVals

  My laptop connects to 46" Sony Bravia LED TV using HDMI cable in Windows without any problem. However, it just doesn't work with Ubuntu 12.04. It always says No Signal. Problem somewhat persists after upgrading to 13.04. Bravia detects my laptop as a connection now but I am unable to display anything. What drivers/applications should I install to connect via HDMI? Output of sudo lspci -nn : 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0101] (rev 09) 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05) 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) 00:1c.1 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 [8086:1c12] (rev b5) 00:1c.3 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 [8086:1c16] (rev b5) 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b5) 00:1c.5 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 [8086:1c1a] (rev b5) 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) 00:1f.0 ISA bridge [0601]: Intel Corporation HM67 Express Chipset Family LPC Controller [8086:1c4b] (rev 05) 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 05) 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05) 01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GF108M [GeForce GT 525M] [10de:0df5] (rev ff) 03:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 1030 [Rainbow Peak] [8086:008a] (rev 34) 04:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 04) 06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06)

  Read the article

• NVIDIA 550M Drivers

  - by DOOM

  First to say, I am newbie, to the linux world and in situation where i have to get used to using ubuntu. My system is: i7-2630QM 8GB Ram with 750GB HD + NVIDIa 550M (1GB) Since i was facing problems with wubi - "slow Ubuntu", i installed it on a separate partition, of 80GB (10GB Swap, 40GB HOME, 30GB ROOT). The system was running fine, before I started using some "CFD" (Graphics Dependent) application. I needed to use "paraview" a graphics software, to design some engineering stuff. Following the installation problems, i installed something called "messa" on my system. The software works but, now my system is "dead-slow". Even with the computer at an idle state, the laptop, is pretty slow, and with huge annoying fan noise. I was tried running some similar applications with windows, and it turns out that its not a hardware, but has to do with the GPU drivers. Following some forums, I installed the "nvidia-current" and now everything is the same. I know, there are many solutions on this forum for nvidia-driver updates, but as you see, nothings working my way. Please someone, tell me what is that I am doing wrong :( This is the output from my terminal for the command lspci | grep 'intel' 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b5) 00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5) 00:1d.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM67 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1030 (rev 34)

  Read the article

• WiFi connected to router, but no internet connection

  - by Quetzacotl

  I just got a new notebook, a ThinkPad Edge E530, and installed Ubuntu on it. I'm pretty new to Ubuntu. On the same laptop, running Windows 7, the Wi-Fi connection works fine. Ethernet connection works both on Win7 and on Ubuntu. Only Wi-Fi on Ubuntu does not work; it connects to the Wi-Fi access point but I don't have Internet access. My wireless card is Intel Centrino Wireless-N 2230. What can fix the problem? EDIT: ifconfig -a eth0 Link encap:Ethernet HWaddr b8:88:e3:30:72:34 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:163 errors:0 dropped:0 overruns:0 frame:0 TX packets:163 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10124 (10.1 KB) TX bytes:10124 (10.1 KB) usb0 Link encap:Ethernet HWaddr 02:15:e0:ec:01:00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 68:5d:43:43:71:e1 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::6a5d:43ff:fe43:71e1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:220 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2801 (2.8 KB) TX bytes:26230 (26.2 KB) route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 127.0.0.1 iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"SATELITE" Mode:Managed Frequency:2.462 GHz Access Point: 00:1F:1F:8D:CC:08 Bit Rate=1 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=60/70 Signal level=-50 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:93 Invalid misc:243 Missed beacon:0 eth0 no wireless extensions.

  Read the article

• Behaviour tree code example?

  - by jokoon

  http://altdevblogaday.org/2011/02/24/introduction-to-behavior-trees/ Obviously the most interesting article I found on this website. What do you think about it ? It lacks some code example, don't you know any ? I also read that state machines are not very flexible compared to behaviour trees... On top of that I'm not sure if there is a true link between state machines and the state pattern... is there ?

  Read the article

• Thinkpad brightness steps error using FN+Home/End

  - by petermolnar

  I've met the following problem: normally my T400 (Lenovo Thinkpad) has 16 steps of brightness, and Windows utilizes it correctly. After a fresh install & minor tweaks Mint 12 (which is based on 11.10 Ubuntu) I only had 6 steps which was way to few. Listing /sys/class/backlight showed 3 entried. I removed the acpi-tools package, one of the disapperared - and I now have 10 steps! Therefore I think if I can reduce the entries to 1 I'm going to have 16 steps, since the stepping will be 1 instead of 2 (or 3). /sys/class/backlight/ intel_backlight -> ../../devices/pci0000:00/0000:00:02.0/drm/card0/card0-LVDS-1/intel_backlight thinkpad_screen -> ../../devices/virtual/backlight/thinkpad_screen The problem is that I'm unable to trace back what are the configs / daemons / kernel options triggers these two. More strangely, I discovered a strange behaviour. I monitored watch -n1 "cat /sys/class/backlight/thinkpad_screen/actual_brightness" and watch -n1 "cat /sys/class/backlight/intel_backlight/actual_brightness" while changing the brightness with FN+home/end combinations from max to min. The outcome is the following: brighness intel thinkpad --------- ----- -------- MAX 2408475 7 | 1955115 5 | 1435640 3 | 1246740 1 | 1086175 0 | 1010615 6 | 859495 4 | 689485 2 v 481695 0 MIN 217235 0 brighness intel thinkpad --------- ----- -------- MIN 217235 0 | 481695 2 | 689485 4 | 859495 6 | 1010615 7 | 1086175 1 | 1246740 3 | 1435640 5 v 1955115 7 MAX 2408475 0 When stepping from MIN to MAX, there's no difference between the last 2 steps. Also, the OSD icon (Cinnamon desktop, default theme) goes from full to min in 4 steps and from full to min once again in 4 steps. So... it seems that the intel entry is working correctly, showing correct values. The thinkpad entry however twists the things and even showing incorrect values. Does anyone have any idea how to get rid of the thinkpad entry? System data: Linux Mint 12 3.0.0-16 kernel Lenovo ThinkPad T400 Cinnamon 1.4 desktop For any additional info, please tell me what do you need. EDIT I'm sorry, I forgot to mention, I added acpi_backlight=vendor to GRUB cmdline as well, this is the result of the semi-better working than the default.

  Read the article

• Should Exterrnal USB hard drive auto mount Ubuntu 12.04.01 LTS

  - by Chris Good

  I want to have external USB hard drives automatically mounted when plugged in. I have 2 drives exactly the same except for volume label. They both have the same UUID. I want to be easily able to swap them as I'm using them for backups and want to keep 1 at home for off site backup. I've set up the /etc/fstab so they should mount at different places based on their volume label: /etc/fstab : LABEL=Passport1 /media/Passport1 ntfs defaults,windows_names,locale=en_US.utf8 0 0 LABEL=Passport2 /media/Passport2 ntfs defaults,windows_names,locale=en_US.utf8 0 0 blkid shows : ... /dev/sdc1: LABEL="Passport2" UUID="4E1AEA7B1AEA6007" TYPE="ntfs" /dev/sdd1: LABEL="Passport1" UUID="4E1AEA7B1AEA6007" TYPE="ntfs" They both mount automatically during reboot but do not mount when just plugged in to a running system. I've read lots of stuff about this, much of it is old so I'm not sure if it applies. I've read some stuff that says the mounts should happen automatically when plugged in, and lots of other stuff that says you have to install other software to make this happen, although much of it just seems to set up the fstab. What's the real story? Here is /var/log/syslog when drive is plugged in: Dec 14 11:22:58 ausyvutims1 kernel: [66221.300196] usb 1-1: new high-speed USB device number 6 using ehci_hcd Dec 14 11:22:58 ausyvutims1 mtp-probe: checking bus 1, device 6: "/sys/devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb1/1-1" Dec 14 11:22:58 ausyvutims1 mtp-probe: bus: 1, device: 6 was not an MTP device Dec 14 11:22:58 ausyvutims1 kernel: [66221.656020] scsi7 : usb-storage 1-1:1.0 Dec 14 11:22:59 ausyvutims1 kernel: [66222.661534] scsi 7:0:0:0: Direct-Access WD My Passport 0748 1016 PQ: 0 ANSI: 6 Dec 14 11:22:59 ausyvutims1 kernel: [66222.666466] scsi 7:0:0:1: Enclosure WD SES Device 1016 PQ: 0 ANSI: 6 Dec 14 11:22:59 ausyvutims1 kernel: [66222.667739] sd 7:0:0:0: Attached scsi generic sg3 type 0 Dec 14 11:22:59 ausyvutims1 kernel: [66222.667913] ses 7:0:0:1: Attached Enclosure device Dec 14 11:22:59 ausyvutims1 kernel: [66222.668047] ses 7:0:0:1: Attached scsi generic sg4 type 13 Dec 14 11:22:59 ausyvutims1 kernel: [66222.678473] sd 7:0:0:0: [sdc] 1953458176 512-byte logical blocks: (1.00 TB/931 GiB) Dec 14 11:22:59 ausyvutims1 kernel: [66222.687700] sd 7:0:0:0: [sdc] Write Protect is off Dec 14 11:22:59 ausyvutims1 kernel: [66222.687705] sd 7:0:0:0: [sdc] Mode Sense: 47 00 10 08 Dec 14 11:22:59 ausyvutims1 kernel: [66222.701076] sd 7:0:0:0: [sdc] No Caching mode page present Dec 14 11:22:59 ausyvutims1 kernel: [66222.701081] sd 7:0:0:0: [sdc] Assuming drive cache: write through Dec 14 11:22:59 ausyvutims1 kernel: [66222.738062] sd 7:0:0:0: [sdc] No Caching mode page present Dec 14 11:22:59 ausyvutims1 kernel: [66222.738068] sd 7:0:0:0: [sdc] Assuming drive cache: write through Dec 14 11:22:59 ausyvutims1 kernel: [66222.754558] sdc: sdc1 Dec 14 11:22:59 ausyvutims1 kernel: [66222.792006] sd 7:0:0:0: [sdc] No Caching mode page present Dec 14 11:22:59 ausyvutims1 kernel: [66222.792012] sd 7:0:0:0: [sdc] Assuming drive cache: write through Dec 14 11:22:59 ausyvutims1 kernel: [66222.792016] sd 7:0:0:0: [sdc] Attached SCSI disk Dec 14 11:22:59 ausyvutims1 ata_id[16971]: HDIO_GET_IDENTITY failed for '/dev/sdc': Invalid argument Thanks for any help offered

  Read the article

• Why is my CPU being used while doing nothing?

  - by Jop

  I have installed Ubuntu GNOME in BIOS mode on my MacBook (BIOS mode so that the proprietary NVIDIA drivers work. I need them for gaming.). For some reason, a lot of CPU is being used while not really doing anything. It swings between 20-30% on both cores, usually. But when I look at the list of processes and sort by CPU usage, I do not see anything special. No processes intensively doing anything. How can I fix this? EDIT: Output of top command. jop@jop-MacBook:~$ top top - 17:08:02 up 41 min, 2 users, load average: 0,51, 0,69, 0,95 Tasks: 202 total, 2 running, 200 sleeping, 0 stopped, 0 zombie %Cpu(s): 11,9 us, 5,8 sy, 0,0 ni, 80,3 id, 0,5 wa, 0,0 hi, 1,5 si, 0,0 st KiB Mem: 7908316 total, 2919940 used, 4988376 free, 153248 buffers KiB Swap: 3906244 total, 0 used, 3906244 free, 1326544 cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 3785 root 20 0 195m 82m 26m S 22,9 1,1 2:43.77 Xorg 4429 jop 20 0 1543m 150m 60m S 7,3 1,9 1:26.26 compiz 4198 jop 20 0 633m 21m 11m S 1,7 0,3 0:04.96 unity-panel-ser 7425 jop 20 0 564m 18m 12m S 1,7 0,2 0:00.84 gnome-terminal 7019 jop 20 0 806m 89m 46m S 1,0 1,2 0:10.01 chrome 7323 jop 20 0 966m 93m 23m S 1,0 1,2 0:06.85 chrome 6742 root 20 0 0 0 0 S 0,7 0,0 0:00.43 kworker/0:3 3 root 20 0 0 0 0 S 0,3 0,0 0:06.01 ksoftirqd/0 7008 root 20 0 0 0 0 S 0,3 0,0 0:00.27 kworker/1:3 7302 jop 20 0 972m 96m 28m S 0,3 1,2 0:06.32 chrome 7310 jop 20 0 382m 63m 39m S 0,3 0,8 0:00.34 chrome 7498 jop 20 0 24840 1600 1120 R 0,3 0,0 0:00.22 top 1 root 20 0 27176 2944 1412 S 0,0 0,0 0:01.58 init 2 root 20 0 0 0 0 S 0,0 0,0 0:00.00 kthreadd 5 root 0 -20 0 0 0 S 0,0 0,0 0:00.00 kworker/0:0H 6 root 20 0 0 0 0 S 0,0 0,0 0:00.00 kworker/u4:0 7 root rt 0 0 0 0 S 0,0 0,0 0:02.04 migration/0 Even when xorg isn't so busy like when I copied, CPU usage is higher then what the processes use.

  Read the article

• What's Bringing SharePoint 2007 Server to a hault?

  - by juanlarios

  I've been having issues with my teste environment and I'm hoping someone has run into this problem and can point me in the right direction. I noticed: SharePoint Server Memory is through the roof at times and so is the CPU usage. Most of CPU usage is a sql proccess. Running out of disk space all the time. I looked in the Logs located in the 12 hive and sure enough I have 1G log files that are hard to open because of the size. The following are the 3 error messages that are flooding my SharePoint logs:   04/05/2010 16:02:36.99     OWSTIMER.EXE (0x0B94)                       0x0BA4    Windows SharePoint Services       Timer                             5uuf    Monitorable    The previous instance of the timer job 'Variations Propagate Page Job Definition', id '{F9A73EB4-90FE-4574-AD99-B4034056F915}' for service '{F89169F9-707B-4588-9ED0-E6D399FE5E3D}' is still running, so the current instance will be skipped.  Consider increasing the interval between jobs.    04/05/2010 15:59:51.51     OWSTIMER.EXE (0x0B94)                       0x0BA4    Windows SharePoint Services       Timer                             5uuf    Monitorable    The previous instance of the timer job 'Profile Synchronization', id '{A05E3439-8DCD-449A-9D9E-46D601CACAA2}' for service '{F89169F9-707B-4588-9ED0-E6D399FE5E3D}' is still running, so the current instance will be skipped.  Consider increasing the interval between jobs.     04/05/2010 15:56:25.53     OWSTIMER.EXE (0x0B94)                       0x0BA4    Windows SharePoint Services       Timer                             5uuf    Monitorable    The previous instance of the timer job 'Scheduled Unpublish', id '{6298F93F-388D-46B9-809E-CEDBB8659661}' for service '{F89169F9-707B-4588-9ED0-E6D399FE5E3D}' is still running, so the current instance will be skipped.  Consider increasing the interval between jobs.     04/05/2010 15:54:14.73     OWSTIMER.EXE (0x0B94)                       0x0BA4    Windows SharePoint Services       Timer                             5uuf    Monitorable    The previous instance of the timer job 'Config Refresh', id '{C42DA970-3DA3-4AA2-94E5-8499C5B80A3E}' for service '{7F6D2CBE-8071-4A30-B313-7C9989FC2D87}' is still running, so the current instance will be skipped.  Consider increasing the interval between jobs.       I'm googling around but haven't found much. I know one other person posted something about this back in 2008, but no answers were reached. I have already checked the databases to see if any of them have gone offline for whatever reason, but from SQL everything is fine. I recently re-created an SSP and deleted an old ssp. So I thought maybe that was causing it, and who knows? maybe that causes some of the problems or maybe all. I'm running configuration wizard and see if anything changes. Please if someone has had similar issues let me know.

  Read the article

• Unable to configure/setup 5.1 audio with 12.04

  - by Vipin Vinayan

  I am kinda new to Ubuntu as well. I have been having this issue with audio for quite sometime now. Initially, when I installed version 11.10 (I guess), I was able to use my 5.1 speakers without any issues. If my memory serves me right, it was after an update that the 5.1 audio stopped working and the video resolution would not get saved. I temporarily fixed the resolution issue by creating a start-up shell script that would update the resolution and load it. But the issue with audio has been going on for quite sometime now. Even though I have option for 5.1, only two speakers seem to be working. I thought an upgrade should fix the issue and so upgraded the OS to version 12.04. I also tried uninstalling alsa and pulse audio, reinstalling them, changing the /etc/pulse/daemon.conf channels from 2 to 6. I have also tried installing pavucontrol but nothing seems to have worked and the issue still persists. Is there anything else you could suggest? The lspci log on my computer is as follows 00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10) 00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port (rev 10) 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 10) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01) 00:1d.0 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) 00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA Controller [IDE mode] (rev 01) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) Would really appreciate a response that will assist me in resolving my issue. Thanks in advance Vipin

  Read the article

• But what version is the database now?

  - by BuckWoody

  When you upgrade your system to SQL Server 2008 R2, you’ll know that the instance is at that version by using the standard commands like SELECT @@VERSION or EXEC xp_msver. My system came back with this info when I typed those: Microsoft SQL Server 2008 R2 (RTM) - 10.50.1600.1 (Intel X86)   Apr  2 2010 15:53:02   Copyright (c) Microsoft Corporation  Developer Edition on Windows NT 6.0 <X86> (Build 6002: Service Pack 2) (Hypervisor) Index Name Internal_Value Character_Value 1 ProductName NULL Microsoft SQL Server 2 ProductVersion 655410 10.50.1600.1 3 Language 1033 English (United States) 4 Platform NULL NT INTEL X86 5 Comments NULL SQL 6 CompanyName NULL Microsoft Corporation 7 FileDescription NULL SQL Server Windows NT 8 FileVersion NULL 2009.0100.1600.01 ((KJ_RTM).100402-1540 ) 9 InternalName NULL SQLSERVR 10 LegalCopyright NULL Microsoft Corp. All rights reserved. 11 LegalTrademarks NULL Microsoft SQL Server is a registered trademark of Microsoft Corporation. 12 OriginalFilename NULL SQLSERVR.EXE 13 PrivateBuild NULL NULL 14 SpecialBuild 104857601 NULL 15 WindowsVersion 393347078 6.0 (6002) 16 ProcessorCount 1 1 17 ProcessorActiveMask 1 1 18 ProcessorType 586 PROCESSOR_INTEL_PENTIUM 19 PhysicalMemory 2047 2047 (2146934784) 20 Product ID NULL NULL   But a database properties are separate from the Instance. After an upgrade, you always want to make sure that the compatibility options (which have much to do with how NULLs and other objects are treated) is at what you expect. For the most part, as long as the application can handle it, I set my compatibility levels to the latest version. For SQL Server 2008, that was “10.0” or “10”. You can do this with the ALTER DATABASE command or you can just right-click the database and select “Properties” and then “Database Options” in SQL Server Management Studio. To check the database compatibility level, I use this query: SELECT name, cmptlevel FROM sys.sysdatabases When I did that this morning I saw that the databases (all of them) were at 10.0 – not 10.5 like the Instance. That’s expected – we didn’t revise the database format up with the Instance for this particular release. Didn’t want to catch you by surprise on that. While your databases should be at the “proper” level for your situation, you can’t rely on the compatibility level to indicate the Instance level. More info on the ALTER DATABASE command in SQL Server 2008 R2 is here: http://technet.microsoft.com/en-us/library/bb510680(SQL.105).aspx Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

  Read the article

• How to troubleshoot ethernet port on laptop

  - by Psallas Vassilios

  I have a problem with my wired connection. To be more specific, my laptop doesn't seems to recognize that I have plugged in an ethernet cable. I tried to download new drivers for my ethernet card, but I couldn't find any solutions. Maybe because I am new to Linux, so I'm not familiar with running commands in the terminal. OK I have typed the command and here are the results: 00:04.0 Ethernet controller [0200]: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter [1039:0191] (rev 02) For the second reply I don't know if the following is what you asked me: ?Memory: 3.9 GiB ?Processor: Intel Core 2 Duo CPU P8800 @ 2.66GHz × 2 ?OS type: 32-bit My Ethernet connection had some problem on Windows too. I have changed recently my internet provider, and since then my ethernet cable is not recognized by the laptop. At that time I was still on Windows. I thought that with Ubuntu the problem would be solved, but unfortunately the problem still persists. If someone can help me to solve my problem I'll be thankful. Here are the results of the three first commands you told me to run: lsmod | grep sis190 sis190 22570 0 sudo modprobe sis190 ifconfig eth0 Link encap:Ethernet HWaddr 00:90:f5:90:81:7e UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:185 errors:0 dropped:0 overruns:0 frame:0 TX packets:185 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:22672 (22.6 KB) TX bytes:22672 (22.6 KB) wlan0 Link encap:Ethernet HWaddr 00:25:d3:2c:3a:ae inet addr:192.168.1.72 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::225:d3ff:fe2c:3aae/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:260 errors:0 dropped:0 overruns:0 frame:0 TX packets:363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:71992 (71.9 KB) TX bytes:52000 (52.0 KB) and the results of running the last two commands: dmesg | grep -e eth -e sis190 [ 0.816667] sis190: sis190 Gigabit Ethernet driver 1.4 loaded [ 0.816728] sis190 0000:00:04.0: setting latency timer to 64 [ 0.816751] sis190: 0000:00:04.0: Read MAC address from EEPROM [ 0.904032] sis190: 0000:00:04.0: Realtek PHY RTL8201 transceiver at address [ 1.416030] sis190: 0000:00:04.0: Using transceiver at address 1 as default [ 1.448235] sis190 0000:00:04.0: eth0: 0000:00:04.0: SiS 191 PCI Gigabit Ethernet adapter at f8410000 (IRQ: 19), 00:90:f5:90:81:7e [ 1.448238] sis190 0000:00:04.0: eth0: GMII mode. [ 1.448243] sis190 0000:00:04.0: eth0: Enabling Auto-negotiation [ 11.560907] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.372019] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.372265] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 26.424038] sis190 0000:00:04.0: eth0: auto-negotiating... nm-tool NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: sis190 State: unavailable Default: no HW Address: 00:90:F5:90:81:7E Capabilities: Carrier Detect: yes Wired Properties Carrier: off

  Read the article

• algorithm for project euler problem no 18

  - by Valentino Ru

  Problem number 18 from Project Euler's site is as follows: By starting at the top of the triangle below and moving to adjacent numbers on the row below, the maximum total from top to bottom is 23. 3 7 4 2 4 6 8 5 9 3 That is, 3 + 7 + 4 + 9 = 23. Find the maximum total from top to bottom of the triangle below: 75 95 64 17 47 82 18 35 87 10 20 04 82 47 65 19 01 23 75 03 34 88 02 77 73 07 63 67 99 65 04 28 06 16 70 92 41 41 26 56 83 40 80 70 33 41 48 72 33 47 32 37 16 94 29 53 71 44 65 25 43 91 52 97 51 14 70 11 33 28 77 73 17 78 39 68 17 57 91 71 52 38 17 14 91 43 58 50 27 29 48 63 66 04 68 89 53 67 30 73 16 69 87 40 31 04 62 98 27 23 09 70 98 73 93 38 53 60 04 23 NOTE: As there are only 16384 routes, it is possible to solve this problem by trying every route. However, Problem 67, is the same challenge with a triangle containing one-hundred rows; it cannot be solved by brute force, and requires a clever method! ;o) The formulation of this problems does not make clear if the "Traversor" is greedy, meaning that he always choosed the child with be higher value the maximum of every single walkthrough is asked The NOTE says, that it is possible to solve this problem by trying every route. This means to me, that is is also possible without! This leads to my actual question: Assumed that not the greedy one is the max, is there any algorithm that finds the max walkthrough value without trying every route and that doesn't act like the greedy algorithm? I implemented an algorithm in Java, putting the values first in a node structure, then applying the greedy algorithm. The result, however, is cosidered as wrong by Project Euler. sum = 0; void findWay(Node node){ sum += node.value; if(node.nodeLeft != null && node.nodeRight != null){ if(node.nodeLeft.value > node.nodeRight.value){ findWay(node.nodeLeft); }else{ findWay(node.nodeRight); } } }

  Read the article

• sony vaio WLAN problem using 12.04

  - by Fredrik

  I'm unable to get my WLAN to work for my Sony Vaio model VPCF23C5E No problem connecting from windows, smartphones etc. $ sudo lshw -C network; lsb_release -a; uname -a; sudo rfkill list; dmesg | grep -i firm *-network description: Wireless interface product: AR9485 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 64:27:37:92:99:0f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-29-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:16 memory:f7000000-f707ffff memory:f7080000-f708ffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 06 serial: f0:bf:97:dd:b2:bd size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-1.fw ip=192.168.1.4 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:50 ioport:9000(size=256) memory:e2104000-e2104fff memory:e2100000-e2103fff LSB Version: core-2.0-amd64:core-2.0-noarch:core-3.0-amd64:core-3.0-noarch:core-3.1-amd64:core-3.1-noarch:core-3.2-amd64:core-3.2-noarch:core-4.0-amd64:core-4.0-noarch Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise Linux siriedit 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no [ 1.287449] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 18.273582] [Firmware Bug]: ACPI(NGFX) defines _DOD but not _DOS Seen some proposed solution e.g. Wireless network cannot be enabled for Sony VAIO E series but answers there don't solve my problem... I'm out of ideas :-( What else can I check? update $ ifconfig -a eth0 Link encap:Ethernet HWaddr f0:bf:97:dd:b2:bd inet addr:192.168.1.4 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::f2bf:97ff:fedd:b2bd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5072 errors:0 dropped:0 overruns:0 frame:0 TX packets:4444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4568435 (4.5 MB) TX bytes:610624 (610.6 KB) Interrupt:50 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1498 errors:0 dropped:0 overruns:0 frame:0 TX packets:1498 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:114156 (114.1 KB) TX bytes:114156 (114.1 KB) wlan0 Link encap:Ethernet HWaddr 64:27:37:92:99:0f inet addr:192.168.1.5 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6627:37ff:fe92:990f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1277 errors:0 dropped:0 overruns:0 frame:0 TX packets:472 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:483155 (483.1 KB) TX bytes:61031 (61.0 KB)

  Read the article

• Fuji camera "mounts" but folder not in Dolphin After Kubuntu 13.10 upgrade

  - by user207207

  Fuji camera mount reported in attached devices but not visible in Dolphin After Kubuntu 13.10 upgrade Have reinstalled the driver, and a few other suggestions, for other cameras mounts failing on previous Ubuntu upgrades. I have already spent a couple of hours trying to get my photo's off the camera, very annoying. Worked perfectly in 11.04, 11.10, 12.04, 12.10 and 13.04. dmesg | tail; lsusb; lsb_release -a [ 6181.858786] CPUM: APIC 03 at 00000000fee00000 (mapped at ffffc90009400000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [17261.396236] CPUM: APIC 00 at 00000000fee00000 (mapped at ffffc90000c6a000) - ver 0x80050010, lint0=0x10700 lint1=0x00400 pc=0x00400 thmr=0x10000 [17261.396239] CPUM: APIC 03 at 00000000fee00000 (mapped at ffffc90000c72000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [17261.396241] CPUM: APIC 02 at 00000000fee00000 (mapped at ffffc90000c70000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [17261.396255] CPUM: APIC 01 at 00000000fee00000 (mapped at ffffc90000c6e000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [32456.884907] usb 2-5: new high-speed USB device number 2 using ehci-pci [32457.654046] usb 2-5: New USB device found, idVendor=04cb, idProduct=01e8 [32457.654050] usb 2-5: New USB device strings: Mfr=0, Product=2, SerialNumber=3 [32457.654052] usb 2-5: Product: Digital Camera [32457.654053] usb 2-5: SerialNumber: 4C3230302020091117CAA59WP18548 Bus 002 Device 002: ID 04cb:01e8 Fuji Photo Film Co., Ltd Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 2013:024f PCTV Systems nanoStick T2 290e Bus 001 Device 002: ID 046d:082d Logitech, Inc. HD Pro Webcam C920 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub No LSB modules are available. Distributor ID: Ubuntu vissibleDescription: Ubuntu 13.10 Release: 13.10 Codename: saucy sudo apt-get install gvfs-bin gvfs-mount gphoto2://[usb:002,002] Error mounting location: Error initializing camera: -108: No such file or directory ...... I have reported a bug in Dolphin, which has been transferred to Solid. Further information : I ran solid-hardware list details udi = '/org/kde/solid/udev/sys/devices/pci0000:00/0000:00:04.1/usb2/2-5' parent = '/org/kde/solid/udev' (string) vendor = '04cb' (string) product = 'Digital Camera' (string) description = 'Camera' (string) Block.major = 189 (0xbd) (int) Block.minor = 137 (0x89) (int) Block.device = '/dev/bus/usb/002/010' (string) Camera.supportedProtocols = {'ptp'} (string list) Camera.supportedDrivers = {'gphoto'} (string list) I still can't get my photo's off, I can see the folders using the Gimp menu. If anyone has got any ideas, I'm willing to try them.

  Read the article

• APress Deal of the Day 2/August/2014 - Pro ASP.NET MVC 5

  - by TATWORTH

  Originally posted on: http://geekswithblogs.net/TATWORTH/archive/2014/08/02/apress-deal-of-the-day-2august2014---pro-asp.net-mvc.aspxToday’s $10 Deal of the Day from APress at http://www.apress.com/9781430265290 is Pro ASP.NET MVC 5. “The ASP.NET MVC 5 Framework is the latest evolution of Microsoft’s ASP.NET web platform. It provides a high-productivity programming model that promotes cleaner code architecture, test-driven development, and powerful extensibility, combined with all the benefits of ASP.NET.”

  Read the article

< Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >