Search Results

Search found 19200 results on 768 pages for 'xp mode'.

Page 62/768 | < Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >

• unable to sniff traffic despite network interface being in monitor or promiscuous mode

  - by user65126

  I'm trying to sniff out my network's wireless traffic but am having issues. I'm able to put the card in monitor mode, but am unable to see any traffic except broadcasts, multicasts and probe/beacon frames. I have two network interfaces on this laptop. One is connected normally to 'linksys' and the other is in monitor mode. The interface in monitor mode is on the right channel. I'm not associated with the access point because, as I understand, I don't need to if using monitor mode (vs promiscuous). When I try to ping the router ip, I'm not seeing that traffic show up in wireshark. Here's my ifconfig settings: daniel@seasonBlack:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:29:9e:b2:89 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8518 (8.5 KB) TX bytes:8518 (8.5 KB) wlan0 Link encap:Ethernet HWaddr 00:21:00:34:f7:f4 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:ff:fe34:f7f4/64 Scope:Link UP BROADCAST RUNNING MTU:1500 Metric:1 RX packets:9758 errors:0 dropped:0 overruns:0 frame:0 TX packets:4869 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3291516 (3.2 MB) TX bytes:677386 (677.3 KB) wlan1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-33-34-00-00-00-00-00-00-00-00 UP BROADCAST NOTRAILERS PROMISC ALLMULTI MTU:1500 Metric:1 RX packets:112754 errors:0 dropped:0 overruns:0 frame:0 TX packets:101 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18569124 (18.5 MB) TX bytes:12874 (12.8 KB) wmaster0 Link encap:UNSPEC HWaddr 00-21-00-34-F7-F4-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Here's my iwconfig settings: daniel@seasonBlack:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:F8:D6:17:34 Bit Rate=54 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=68/70 Signal level=-42 dBm Noise level=-69 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 wmaster1 no wireless extensions. wlan1 IEEE 802.11bg Mode:Monitor Frequency:2.437 GHz Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Here's how I know I'm on the right channel: daniel@seasonBlack:~$ iwlist channel lo no frequency information. eth0 no frequency information. wmaster0 no frequency information. wlan0 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6) wmaster1 no frequency information. wlan1 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6)

  Read the article

• SQL Server Database In Single User Mode after Failover

  - by jlichauc

  Here is a weird situation we experienced with a SQL Server 2008 Database Mirroring Failover. We have a pair of mirrored databases running in high-availability mode and both the principal and mirror showed as synchronized. As part of some maintenance I triggered a manual failover of the principal to the mirror. However after the failover the principal was now in single-user mode instead of the expected "Principal/Synchronized" state we usually get. The database had been in multi-user mode on the previous principal before this had happened. We ended up stopping all applications, restarting the SQL Server instances, and executing "ALTER DATABASE ... SET MULTI_USER" to bring the database back to the expected "Principal/Synchronized" state in a multi-user mode. Question. Does anyone know where SQL Server stores information about whether a database should be in single-user mode or not? I'm wondering if there is some system database or table that has this setting recorded somewhere. In particular we had an incident once with the database on the original principal (the one I was failing over to) where when trying to detach the database it was put into single-user mode. I'm wondering if that setting is cached somewhere and is the reason that SQL Server put it back into single-user mode after a failover.

  Read the article

• Emacs - nxhtml-mode - memory full

  - by mbutz

  working with nxhtml-mode in emacs, I get problems since a few weeks. While working emacs pauses unexpectingly until showing a message in the mode line "!MEM FULL!"; obviously nxhtml-mode is filling up the memory until emacs stopps to work. I am working with html, php and css files. I have no idea how I could debug this problem in a meaningfull way. Also I seem to be the only one to have this problem, because googling did not deliver any answers to this question. I am using emacs 2.32 on an Linux Mint 11 system. I can not find out the verson of nxhtml, it says revision 829 downloaded from http://bazaar.launchpad.net/~nxhtml/nxhtml/main/revision/829. I set up a test scenario with a minimal dot-emacs just to test the nxhtml-mode. It seemed to be alright, but it does not reflect my productive set up. It would probably take a week or so to gradually include everything I used to use within emacs (e.g. org-mode) while testing whether nxhtml-mode does not like anything, which is called in my dot-emacs file. Is there another way? Can I find out, what causes the memory overload? Does anyone has similar problems using nxhtml-mode? Greetings Martin

  Read the article

• Recovering from backup without original install media

  - by KGendron

  A machine from my old job had a complete hard drive failure. I have backups but I'm running into severe problems restoring from them. The only install media was a secondary restore partition on the system's hard drive. I hate whoever came up with that idea more than i can possibly express with words. I spent several days trying to recover the disk - it is pretty well shot and none of my best tricks could even get it to show up in the bios/ The machine that broke is an hp with xp media center edition on it (I don't know why either). The backups were created using the default windows backup tool - I have .bfk file on an external hardrive that i am trying to restore from. I've replaced the hard drive. My home machine is running windows 7 64bit and i'm trying to use it as a platform to restore to the other disk. I downloaded the window 7 nt-restore utility, however no matter what i do it restores to my C drive rather than the specified drive. Fortunately win7 security settings prevented it from being a complete disaster - but still not a happy thing. I tried firing up the xp virtual machine. I can browse to the backups but it says they are invalid and refuse to let me view/ continue with the restore. I tried installing XP to an extra harddrive on my machine - however it bluescreens on me during the install process and I cry. I tried installing xp pro to the new drive and attempted to restore over it, it of course blackscreened on me as that was a stupid idea. I made two partitions on the new hard drive (Apparently the bios on this accursed piece of junk doesn't allow hd partitions larger than 200G anyways and thus fails 40 minutes into the install with an ever-descriptive "Disk Read Error". Guess how i spent last weekend? My last idea was to install xp pro to the second partition and then use it to restore from backup to the first. After the first restart it gives me the error "Windows could not start because of a computer disk hardware configuration problem. Could not read from the selected boot disk. Check boot path and disk hardware". My brain made one of those bad hard drive clicky noises. I've tried several boot disks but they don't seem to work. If anyone has a link to a good one it would be greatly appreciated. Anyone have any more ideas? - I really hate asking on what seems like such a simple issue but i am quite literally at my wit's end. Thanks - and sorry for the really long post.

  Read the article

• Download Angry Birds For Windows 7 & Windows XP

  - by Gopinath

  The famous Angry Birds game from Rovio is now available for your personal computers. You can download the game from Intel’s App Store for windows. It costs $5 and supported on Windows 7 and Windows XP computers. Here is a video of Angry Birds running on Windows 7 Laptop. The survival of the Angry Birds is at stake. Dish out revenge on the green pigs who stole the Birds’ eggs. Use the unique destructive powers of the Angry Birds to lay waste to the pigs’ fortifications. Angry Birds features hours and hours of challenging physics-based demolition gameplay, with lots of replay value. Each level requires a mixture of logic, skill, and brute force to crush the enemy. Download Angry Birds For PCs From Intel AppUp This article titled,Download Angry Birds For Windows 7 & Windows XP, was originally published at Tech Dreams. Grab our rss feed or fan us on Facebook to get updates from us.

  Read the article

• Windows 7 cannot view FAT32 formatted bootable usb drive

  - by NaimK

  I'm having some issue where when I run bootsect with a command line of "bootsect.exe /nt52 : /force /mbr", then Windows 7 (the comp I'm running bootsect on) can no longer view the contents of the usb drive. Explorer tries to look at it, and then fails, and I can't even correctly eject the drive, when I try, it does nothing until I yank it out, and then I get some errors. Bootsect reports success on writing the volume and the drive data to make it bootable, but it doesn't boot after copying on the necessary files (files from a created ISO, it works when it is created on XP). But this may be that I'm not following the same instructions as when building it on XP since some of the command don't seem to always work correctly. The drive is formatted to FAT32 (necessary I think, cause I'm installing a custom version of Win XP embedded). Any ideas? Or perhaps a good or automated way to load a usb with a custom version of win xp and make it bootable from Win 7? I am having some issues, for instance, "ufdprep.exe" rarely works when I'm running it from Windows 7, I don't know why.

  Read the article

• Networking Problem MrxSmb event 50 "Delayed Write Failed" errors occurring all of the sudden

  - by Johnny Musso

  JUST THIS MONTH, we have started getting reports from a number of very stable clients that MrxSmb event id 50 errors keep appearing in their system event logs. Otherwise, they do not appear to have any networking problems except that there is a critical legacy application which seems to either be generating the MrxSmb errors or having errors occur because of them. The legacy application is comprised of 16 bit and 32 bit code and has not been changed or recompiled in many years. It has always been stable on Windows XP systems. The customers that have the problem usually have a small (5 clients or less) peer to peer network with all Windows XP systems. All service packs are loaded on the XP machines. Note: The only thing that seems to correct the problem is disabling opportunistic locking. I don't like this solution because it seems to slow down the network and sometimes causes record locking issues between users (on some networks). Also, this seems to have just started happening - as if a Windows update for XP has caused it? However, I have removed recent updates and it did not correct the issue. Thanks in advance for any help you can provide.

  Read the article

• Remote desktop connection to network printer

  - by andand

  I'm trying to print a document from a remote WinXP machine to a network printer I use on a local Win7 machine using Remote Desktop. The network printer does not appear in the list of those available on the WinXP box. In more detail, the local machine runs Windows 7 (no admin rights) and connects to a network printer managed by a print server (i.e. not using a local TCP/IP Port). I have access to a Windows XP host on a separate network which I access using Remote Desktop. I would like to have print requests from the remote XP box forwarded to the network printer I use on the Windows 7 machine. The XP machine cannot access the print server I use on the Win7 machine nor can it create a TCP/IP port to connect directly to the printer (network configuration issues). After having consulting the KB312135 I confirmed the "Printers" option was selected in the Remote Desktop Client, Local Resources Tab, yet the network printer does not appear on the list of available printers on the XP box. Is this a lost cause or is there something else I haven't managed to locate yet?

  Read the article

• java: how can i set the compatibility mode of a native .exe?

  - by Jakob

  So i have a native executable (both for OS X and Windows) tucked inside a .jar, which is then programatically extracted to a temp location and executed from there. Unfortunately this executable will not run properly on my Windows machine (Win 7 64bit), when i manually set the compatibility mode to a Windows XP preset however, it will work. Is there a way i can do this programatically from Java?

  Read the article

• Why is my boot loader's stack segment at 0x3FF (end of Real Mode IVT)?

  - by Laurimann

  Title says it all. "address 0x500 is the last one used by the BIOS" - en.wikipedia.org/wiki/Master_boot_record "00000000-000003FF Real Mode IVT (Interrupt Vector Table)" - wiki.osdev.org/Memory_Map_%28x86%29 So can you tell me why NASM places my .com file's stack pointer to 0x3FF while my instruction pointer starts at 0x7c00? To me the most intuitive place for SP would be right below 0x7c00. Thanks.

  Read the article

• Toshiba External Hard Drive freezes computer

  - by Ephraim

  I bought a Toshiba Canvio Basics E05A032BAU2XK Portable External 320GB 2.5 Hard Drive: My computer has two Os's on it Win7 and Win XP. I need both. The main one I use is XP. When booting my computer in any OS the computer and hard drive work fine. The same holds true for plugging in the hard drive while running Win7. However, when running WinXP, if the hard drive gets plugged in the computer freezes(my main point is that the HD is portable so it is essential that it does not do this, as I said I usually run XP). After reading some online forums I was informed that there is a compatibility issue with the newest version of Eset Smart Security(I still don't understand this because it works fine in Win7 or when connected on boot...). I disabled the AV and plugged in the HD... Walla! The comnputer did not freeze. However the disk is not recognized in explorer or disk management. In device manager I removed the device and did a scan and installation of device failed. It pretty much sounds like a driver issue but I cannot find any drivers for this HD. In fact, Toshiba claims that there are no downloadable drivers for it and that XP should take care of the drivers itself. What to do? As far as I can tell, all other USB devices work just fine on both OS. Please Help!

  Read the article

• UITableViewCell indentation not in edit mode.

  - by Eric P.

  When you enter editing mode on a grouped-style UITableView, the cells indent to show the editing control (if you aren't sure what I mean, see this picture (editing mode) http://i.imgur.com/GJXvL.png and this (non-editing mode) http://i.imgur.com/ahKYS.png). I am trying to manually indent a cell when the tableView is not in editing mode. I tried the indentationLevel property, but that just moves the text further to the right inside the cell and doesn't actually change the cell. Any ideas?

  Read the article

• Is there an IE8 setting or policy to make it work like IE7 with respect to persistent connections?

  - by Stephen Pace

  I am working with a commercial application running on XP using IIS 5.1. Periodically the application is returning an IIS error "There are too many people accessing the Web site at this time." This is caused by Microsoft artificially limiting the number of connections (10) under IIS 5.1 under Windows XP, but in this case, there is really only one user (albeit a few tabs open at a time). Microsoft suggests you can reduce the problem by turning off HTTP Keep-Alives for that particular web site: http://support.microsoft.com/kb/262635 If you use IIS 5.0 on Windows 2000 Professional or IIS 5.1 on Microsoft Windows XP Professional, disable HTTP keep-alives in the properties of the Web site. When you do this, a limit of 10 concurrent connections still exists, but IIS does not maintain connections for inactive users. I may do that; however, I'm worried about performance degradation. However, I also notice that IE8 appears to handle this differently than IE7. By default, IE6 and IE7 use 2 persistent connections while IE8 uses 6. Perhaps in this case IE8 itself is generating multiple connections in an attempt to be faster, but those additional connections are overwhelming the artificially limited IIS 5.1 on XP? Assuming that is the case, is there an Internet Explorer option, registry setting, or policy I can set to force IE8 to behave like IE7 with respect to persistent connections? I would not set this for all users, but for the small number of users that used this application, it might solve their intermittent problem until the application can be rehosted on Windows Server 2008. Thanks.

  Read the article

• How to move a sata drive to a machine without AHCI mode

  - by Andrew Cooper

  I've got a Dell Inspiron 1545 on which the screen has died. I'm able to plug an external monitor into the Inspiron 1545 and it works fine, so the screen is the only issue. The OS is Win7. I'm trying to move the disk to a spare Dell Precision M90 laptop that I've got lying around. The problem is that almost as soon as the Windows logo appears in the boot sequence I get a BSOD with a STOP 0x0000007B message. Researching this message pointed to issues with SATA AHCI mode. I looked in the BIOS of the Inspiron 1545 and the controller was set to AHCI mode. I set it to ATA mode and tried to boot with the same drive and got the same result as on the Precision M90. Switching back to AHCI allowed the machine to boot correctly again. I checked the BIOS on the Precision M90 and it doesn't seem to support AHCI mode, although it is a SATA controller onboard. The BIOS is the latest A08 version available from Dell. Is there any way I can get this drive to boot in the M90 without reformatting it?

  Read the article

• Certain Japanese characters aren't displayed properly

  - by Nisto

  On the following site: http://www.nciku.com/search/radical the first 2 characters on the second row of the "Step 2" table aren't displayed properly. All other characters look fine. I tried re-installing the Asian fonts via the checkboxes regarding Asian fonts in the "Regional and Language Options" control panel applet. I have tried removing every single Font from the Fonts folder (some were ofcourse not possible to remove), and re-installing them all again. I did this by... Running cmd Closing down the explorer process In cmd; using the command DEL /F /S /Q * in the Fonts folder Putting in my XP SP3 Retail disc In cmd; using expand -r *.tt_ in the I386 folder on the XP disc (and any other font file, in the I386\LANG folder) I also tried installing this pack from Microsoft, but this solved nothing either. I even tried running my browser (Firefox) through AppLocale. And changing character encoding -- again, does not help. I've also tried viewing the page in Internet Explorer. What could be wrong? I have checked my Fonts folder, to make sure that every single font available on the XP disc is available in WINDOWS\Fonts. What shows in the first square on the second row - I can't really tell what it's supposed to look like (but it's not the proper character)... but the second square shows a rectangular symbol containing HEX code. I've been in this situation before -- and it has been when I've been missing fonts. But how could I possibly be missing a necessary font? Shouldn't it be provided in the Asian "font packages"? I've talked to some other users that has viewed the page, and they had no problems displaying those characters on second row - even though they're only using the fonts provided on the Windows installation disc. Windows XP Professional Service Pack 3 (x86 - with latest updates) Firefox 3.6.15

  Read the article

• Unable to access network resources through VPN

  - by fbueckert

  I'm currently attempting to connect one of our computers in the office to a client VPN. My development machine is running Windows 7, and can connect and see resources just fine. The problem computer is running Windows XP. They're both within the same network. Using the same credentials at both computers, the VPN connection (using the built in Windows network connections) works just fine. So far, so good. An IP address is assigned, and comparing both machines shows they're still in the same subnet. The problem is that the XP machine cannot see ANY of the computers in the client network. I tried a tracert to a target machine on the Windows 7 box, and the first item that comes up is the .0 address. Pinging it gives responses. Trying it on the Windows XP machine, however, comes up with just timeouts. Trying to trace to www.google.com allows the address to resolve (probably part of the cached resolutions), but results in just timeouts. I double-checked to make sure that the Windows firewall was not on, and trying to open the settings brings up a notification that the firewall service wasn't running, which leads me to believe that it's definitely not on. From my best guess, I've managed to connect the XP machine to a black hole of some sort. There's obviously something strange going on, but I'm not sure where I should be looking.

  Read the article

• Monitor mode 802.11 captures on OSX

  - by Mike A

  I'm trying to determine the difference between capturing 802.11 frames in the following ways on OSX (10.8.5). It's a bit esoteric, but I use "Option 2" to capture frames for later analysis, and am wondering if I'm missing something. Option 1: use "airportd": $sudo /usr/libexec/airportd en0 sniff Option 2: use "airport" followed by tcpdump: sudo /System/Library/PrivateFrameworks/Apple80211.framework/Versions/Current/Resources/airport --channel= sudo tcpdump -I -P -i en0 -w /tmp/capture.pcap (or alternatvely eliminate the -w and watch packets real-time). From what I can tell: Both commands, according to the wifi icon on OSX, put the interface into 'monitor' mode. Both commands output a pcap file that is readable in both wireshark/tcpdump & Eye PA. Both commands appear to capture management, control and data frames. The rub: Option 1 disconnects you from the network. This is expected, when putting an interface into 'monitor' mode. Option 2 does NOT disconnect you, provided you've set the channel to the same channel your currently connected to. This has a distinct advantage of keeping your connection up while capturing in monitor mode. My question: Option 2 does not seem like it should work, or more specifically, it does not seem like I should be able to remain connected while also capturing frames in monitor mode. On a wired NIC, you can be 'promiscuous' and still send frames, though I didn't think the same was true for wireless NIC. I'm questioning the validity of capturing frames w/ Option 2?

  Read the article

• How can I programatically force Windows XP to display thumbnails for a folder?

  - by George Edison

  I have an application that calls ShellExecute with a folder path. This brings up the folder in explorer. However, I want to make sure that the folders are set to display the contents in thumbnail view. How can I ensure this?

  Read the article

• CSS filter for IE6 standard mode and quirk mode?

  - by jackysee

  Is there any CSS filter can be applied to detect IE6's standard mode and quirk mode? The story is that a jQuery script is using $.support.boxModel to handle different rendering mode. But the CSS use the *width hack to define the dimension. But this hack can only filter whether the browser is IE but not the real rendering mode IE is on.

  Read the article

• On a local network, are you able to password protect certain folders and how (in windows xp)?

  - by Derek

  I have a local network set up for my small office which consists of me, the manager, my wife, the secretary, and a few sales people/others. I would like to share passwords over the network and other such things privately to my wife, the secretary, but would not like the sales people and others to have access to it, yet I need the others to have access to other folders/documents that I'd like to share. How would I go about doing this if not by password? Thanks in advance

  Read the article

• Does IE8 in compatibility mode display web-pages like IE7?

  - by Patrick

  hi, is debugging in compatibility mode in IE8 exactly the same than debugging in IE7 ? do the websites display exactly the same ? So I don't need IE7 for testing if I have IE8 ? thanks

  Read the article

• Questions about explorer.exe

  - by nmuntz

  Hi, I was given by my company a laptop with Windows XP Professional in Spanish. I would like to translate it to English, since I really DISLIKE to use localized versions of programs. I have read about Windows MUI packs, however you MUST have Windows XP Pro in English in order to translate it to other language, you can't translate it TO English from other language. Since reinstalling the OS using a Win XP CD in english is not an option (don't have the license nor the CD, and don't have domain privileges to rejoin my computer to the domain), I was wondering what are the essential files that contain localized strings of text. I was doing some research, and apparently explorer.exe has many of the Windows Error Messages and other strings. Will replacing my original explorer.exe with one from Windows XP in English be enough (and work) for having a "basic" english version of windows? Im mainly interested in having error messages, start menu, and the control panel in english. Also, does it HAVE to be the same version as the Service Pack im running? Besides explorer.exe are there any other essential files that i should try to get and replace? Do you see any "dangers" in replacing this files with english version ones? Thanks in advance for your help.

  Read the article

• How long does it take each thread timeslice in Windows XP ?

  - by IHawk

  I am trying to find out how long does it take each thread timeslice (quantum) in Windows but the only information that I found out is about the clock ticks being from 15 to 20ms or 20-30ms. How can I find this information ? I think it may vary from OS to OS, but I am not certain. I appreciate any suggestion on this subject. Thank you.

  Read the article

• How to delay user login until RunOnce is completed? [Win XP]

  - by Shaitan00

  Currently I have an application that runs at startup when a user log's in to the account (administrative), as well as something under HKLM...\Run which is also executed - but I need to run something once and BEFORE both these things are executed. My solution was to use HKLM...\RunOnce which is executed before the HKLM...\Run but the task can take 30-45 seconds which gives enough time for the user Startup to be executed and launch the application prematurely. I thought of maybe including a SLEEP but RunOnce doesn't block the user account load... Then I considered the group policies but they do not have a RunOnce equivalent that I can use... Also I am not sure if Group Policy is run at the right time (never used it before). Is there anyway to make my RunOnce delay the account startup of my application, or a better place where I can execute it before both HKLM...\Run and user Startup? Or any recommended alternatives? Any ideas or help would be much appreciated... Thanks,

  Read the article

• How do I reformat/reinstall an OS on a hard drive after its been wiped by eban?

  - by Aggrevated

  I am trying to install XP SP2 Home on a Dell Inspiron 531s. Yes it came with Vista but I happen to own a legal copy of XP. I bought the hard drive off eBay(used). I changed the bios settings to boot from CD and when I start up the computer it goes to the hard drive which says its been cleaned using eban XX.XXX.XXX. My problem is that I can't get the PC to boot from the XP disk. I have tried putting the disk into another PC it works. I have put the bad hard drive back in and the dvd+rw works. I am really stumped and am beginning to think that the hard drive is unusable. I only have the sata cords for 1 hard drive to be hooked up at a time. Any ideas or suggestions or confirmation that I can't use this hard drive would be appreciated. Yes I am probably a 'noob' but I have installed XP and Vista many times without any problems. I don't need to be put down on my level of experience I just need answers. Thanks Everyone

  Read the article

< Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >