Search Results

Search found 36619 results on 1465 pages for 'damn small linux'.

Page 624/1465 | < Previous Page | 620 621 622 623 624 625 626 627 628 629 630 631  | Next Page >

• Titanium SDK gives a "file too short" error

  - by Dananjaya

  I'm using Ubuntu 11.04 and recently installed Appcelerator Titanium Studio version 1.7 When I load up a demo project to run, I get an error like this, Couldn't load file:/home/dananjaya/.titanium/runtime/linux/1.1.0/libkhost.so, error: /home/dananjaya/.titanium/runtime/linux/1.1.0/libwebkittitanium-1.0.so.2: file too short Am I missing some dependencies here or is it a bug in the application? Thanks in advance.

  Read the article

• FM Radio without Internet?

  - by WitchCraft

  Question: Is it possible to use FM radio WITHOUT internet connection or special devices ? On my Android phone, I can plug in the headphones, which are in turn used as antenna. Since Android is Linux and Ubuntu is also Linux, it should be possible to do this on a plain old Ubuntu notebook (13.04), too. Is it ? If yes, which application can I use for FM-Radio ? Note: I repeat: Live FM-Radio WITHOUT internet connection at the time of listening :)

  Read the article

• Unable to boot post upgade to 12.10 from 12.04 on a dial boot PC

  - by Prateek

  I have a dual boot PC with Win7 and Ubuntu. Last night I upgraded from 12.04 to 12.10 and since then I have not been able to boot and PC goes into grub rescue with error "File not found" I have tried the below steps set prefix=(hd0,msdos5)/boot/grub/i386-pc/ set root=(hd0,msdos5) insmod normal ( i get error symbol not found : 'grub_disk_dev_list'. when I try linux /boot/vmlinuz-3.2.0-32-generic root=/dev/sda5 ro (i get error - command not found 'linux' ) same for initrd I am not able to find out what sdXX to set also.

  Read the article

• Oracle Database 11g Release 2 - Patchset 11.2.0.4 available now!

  - by A. G.

  DB 11.2.0.4 patchset (Patch 13390677) has been released on Linux x86-64 Linux x86 Solaris on SPARC (64-bit) Solaris x86-64 HP-UX Itanium IBM AIX on Power Systems Microsoft Windows x64 (64-bit) Microsoft Windows (32-bit) Additional details about list of bug fixes and known issues is available via My Oracle Support Document 1562139.1 11.2.0.4 Patch Set - Availability and Known Issues Document 1562142.1 List of Bug Fixes by Problem Type New features are listed in Oracle Database New Feature Guide - Oracle Database 11g Release 2 (11.2.0.4) New Features

  Read the article

• Tiny DIY PC gets smaller, more powerful

  <b>Linux Devices:</b> "The Linux-ready Artigo A1100 has a 1.3GHz Via Nano processor, accepts 2GB of RAM, sports HDMI and VGA video outputs, and has five USB ports, the company says."

  Read the article

• There is no driver for Ralink chip 5360

  - by Dmitrix

  I bought DWA-525 and it does not work Google did not help. No one on the Internet could not get the device to work =( lspci 01:06.0 Network controller: Ralink corp. Device 5360 I do not know what to do uname -a Linux pc 3.0.0-19-generic #33-Ubuntu SMP Thu Apr 19 19:05:57 UTC 2012 i686 athlon i386 GNU/Linux cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10" I am sure that the problem is DWA-525 and chip 5360. I found many similar problems on the Internet without solving =(

  Read the article

• Making my own custom Ubuntu

  - by Benny

  I was wondering, is it possible to make my own customized version of Linux based on Ubuntu 10.10 ? I am thinking of calling it something different but I was wondering besides making a custom Live CD I am talking about an Linux that people can install on there computers using Ubuntu installation method. I want to base it on something other than GNOME but be able to install it latter on. Thanks in advance, Benny

  Read the article

• Getting WLAN on my Laptop to work (Medion MD98300)

  - by Anand Böhmer

  Dear Ubuntu Community, I am having difficulties to get the WLAN Adapter on my Medion 98300 Laptop to work. The WLAN Card seems to be connected through an internal USB Interface and the Card itself had shown up as a wirelles Network while installing Ubuntu. I have tried a few things earlier, but none of my google reasearches have brought me to a working solution... I am quite new to the Linux System and only knoew a couple of terminal commands so far, so I probably have missed out on a few possible solutions. Maybe you can help me? Thank you very much in advance! A fre minimal technical Details: AMD Turion 64 X2 Dual-Core Mobile Technolgie TL-50 NVIDIA GeForce Go 6150 SanDisk 64GB SSD 2GB RAM DDR2 667 nForce Chipset (I forgt the Version, but deductable from the GPU I guess) WiFi: ZyDAS ZD1211B 802.11g Thank's a lot again! :) UPDATE: I tried around myself a little and found a guide on the Linux Mint forums that helped! I already had tried to install the linux backport modules etc. What I finally did was update the linux firmware and run the following command: echo "options acer_wmi wirelles=1" sudo tee /etc/modprobe.d/acer_wmi.conf and rebooted now I found and could connect to networks, but unfortunately I found, that the link quality was very bad, around 40 to 50. Eventhough my Router is running at high power and is only 6 Meters away! I then switched a few channels, but that did not improve much. Before, under Windows, I had a very good link quality and had the entire 16mbit/s internet connection at disposal, now I can only get about 3-5Mbit/s. better then nothing, but still pretty bad! The "TX power" is fixed on 20dBm and iwconfig says, that the "Power Management" is off... Maybe the power of the module is set too low?... UPDATE2: I figured that 20dBm is a normal power output. I even tried to change the power using iwconfig wlan0 txpower INTEGERHERE but, obviously my "Card" does not support more then 20. More would probably be illegal as well, so I won't even use more then 20. I guess that I will have to figure out a way, or maybe just switch cards. Are the Mailboard-USB-Connectors on a laptop of the same property as the standard external ones? If so, I could simply solder a micro Wirelless N Adapter onto the board :)

  Read the article

• Brasero Burns Data, Not Time - or Piles of Discs

  <b>Linux Insider:</b> "There are a lot of CD/DVD burners for Linux out there, but Brasero stands out as a straightforward, easy-to-use, burner that has some nice extra features but won't make you relearn a lot of complex commands if you only use it occasionally. One nicety is the option to start a burn project and finish it much later, even if you're not using a rewritable disc."

  Read the article

• Acer Allionone Z5810 Touchscreen Issues 12.04

  - by Johannes

  I have an Acer Allionone Z5810, and I can't get the touchscreen to work after I install 12.04. Here is the lsusb output: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 0596:0508 MicroTouch Systems, Inc. Bus 001 Device 004: ID 04b8:0005 Seiko Epson Corp. Printer Bus 001 Device 005: ID 07ca:1336 AVerMedia Technologies, Inc. Bus 002 Device 003: ID 04ca:0058 Lite-On Technology Corp. Bus 002 Device 004: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 002 Device 005: ID 04f2:b23f Chicony Electronics Co., Ltd xinput --list Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? Lite-On Technology Corp. Wireless Device id=9 [slave pointer (2)] ? ? Lite-On Technology Corp. Wireless Device id=10 [slave pointer (2)] ? Virtual core keyboard id=3 [master keyboard (2)] ? Virtual core XTEST keyboard id=5 [slave keyboard (3)] ? Power Button id=6 [slave keyboard (3)] ? Power Button id=7 [slave keyboard (3)] ? Lite-On Technology Corp. Wireless Device id=8 [slave keyboard (3)] ? USB 2.0 camera id=11 [slave keyboard (3)] ? AT Translated Set 2 keyboard id=12 [slave keyboard (3)] My xorg.conf contains: nvidia-xconfig: X configuration file generated by nvidia-xconfig nvidia-xconfig: version 304.48 (buildmeister@swio-display x86-rhel47-04.nvidia.com) Sun Sep 9 21:31:39 PDT 2012 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" InputDevice "TouchScreen" EndSection Section "Files" EndSection Section "InputDevice" Identifier "TouchScreen" Driver "microtouch" Option "Type" "finger" Option "Device" "/dev/ttyS3" Option "ScreenNo" "0" Option "MinX" "0" Option "MaxX" "16383" Option "MinY" "0" Option "MaxY" "16383" Option "SendCoreEvents" "yes" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" HorizSync 28.0 - 33.0 VertRefresh 43.0 - 72.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection

  Read the article

• Package dependency errors : libc

  - by piyush

  I was trying to install kde-full when the libc had some unmet dependencies error. When saying sudo apt-get install kde-full the terminal has this in the end libc6 : Depends: libc-bin (= 2.15-0ubuntu10) libc6:i386 : Depends: libc-bin:i386 (= 2.15-0ubuntu10) libc6-dev : Depends: libc6 (= 2.15-0ubuntu10.3) but 2.15-0ubuntu10 is to be installed libc6-i386 : Depends: libc6 (= 2.15-0ubuntu10.3) but 2.15-0ubuntu10 is to be installed When running sudo apt-get -f install, this shows up at the end De-configuring libc6:i386 ... A copy of the C library was found in an unexpected directory: '/lib/x86_64-linux-gnu/libc-2.15.so' It is not safe to upgrade the C library in this situation; please remove that copy of the C library or get it out of '/lib/x86_64-linux-gnu' and try again. dpkg: error processing /var/cache/apt/archives/libc6_2.15-0ubuntu10.3_amd64.deb (--unpack): subprocess new pre-installation script returned error exit status 1 Preparing to replace libc6:i386 2.15-0ubuntu10 (using .../libc6_2.15-0ubuntu10.3_i386.deb) ... De-configuring libc6 ... A copy of the C library was found in an unexpected directory: '/lib/i386-linux-gnu/ld-2.15.so' It is not safe to upgrade the C library in this situation; please remove that copy of the C library or get it out of '/lib/i386-linux-gnu' and try again. dpkg: error processing /var/cache/apt/archives/libc6_2.15-0ubuntu10.3_i386.deb (--unpack): subprocess new pre-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/libc6_2.15-0ubuntu10.3_amd64.deb /var/cache/apt/archives/libc6_2.15-0ubuntu10.3_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1) Any suggestions how to fix this. I don't desire to have kde-full anymore; only that other installations should work. I've done sudo apt-get update several times, so those suggestions can be kept away UPD : here is output of dpkg configure ~$ sudo dpkg --configure -a dpkg: dependency problems prevent configuration of libc6-dev: libc6-dev depends on libc6 (= 2.15-0ubuntu10.3); however: Version of libc6 on system is 2.15-0ubuntu10. dpkg: error processing libc6-dev (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libc6-i386: libc6-i386 depends on libc6 (= 2.15-0ubuntu10.3); however: Version of libc6 on system is 2.15-0ubuntu10. dpkg: error processing libc6-i386 (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: libc6-dev libc6-i386 ~$

  Read the article

• ubuntu 13.04 recognizes usb mobile broadband modem as ethernet connection

  - by Bence Mihalka

  When I plug in my usb mobile broadband modem (ZTE MF-667), in the network manager instead of a mobile broadband connection, I get an ethernet connection, called: Ethernet Network (ZTE WCDMA Technologies MSM), which of course doesn't work. Here is my lsusb output and the relevant parts of dmesg output: lsusb: Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0cf3:3005 Atheros Communications, Inc. AR3011 Bluetooth Bus 001 Device 004: ID 04f2:b1b9 Chicony Electronics Co., Ltd Asus Integrated Webcam Bus 001 Device 005: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 002 Device 004: ID 19d2:1405 ZTE WCDMA Technologies MSM dmesg: [ 195.328467] usb 2-1.1: new high-speed USB device number 3 using ehci-pci [ 195.423545] usb 2-1.1: New USB device found, idVendor=19d2, idProduct=1225 [ 195.423555] usb 2-1.1: New USB device strings: Mfr=3, Product=2, SerialNumber=4 [ 195.423561] usb 2-1.1: Product: ZTE WCDMA Technologies MSM [ 195.423567] usb 2-1.1: Manufacturer: ZTE,Incorporated [ 195.423572] usb 2-1.1: SerialNumber: P680A1ZTED000000 [ 195.426319] scsi7 : usb-storage 2-1.1:1.0 [ 196.425354] scsi 7:0:0:0: CD-ROM CWID USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2 [ 197.447919] usb 2-1.1: USB disconnect, device number 3 [ 197.457582] sr0: scsi3-mmc drive: 243x/186x xa/form2 cdda pop-up [ 197.457594] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 197.459058] sr 7:0:0:0: Attached scsi CD-ROM sr0 [ 197.459483] sr 7:0:0:0: Attached scsi generic sg2 type 5 [ 197.759186] usb 2-1.1: new high-speed USB device number 4 using ehci-pci [ 197.854543] usb 2-1.1: New USB device found, idVendor=19d2, idProduct=1405 [ 197.854556] usb 2-1.1: New USB device strings: Mfr=4, Product=3, SerialNumber=5 [ 197.854564] usb 2-1.1: Product: ZTE WCDMA Technologies MSM [ 197.854572] usb 2-1.1: Manufacturer: ZTE,Incorporated [ 197.854579] usb 2-1.1: SerialNumber: P680A1ZTED010000 [ 197.957739] scsi8 : usb-storage 2-1.1:1.2 [ 198.076554] cdc_ether 2-1.1:1.0 eth1: register 'cdc_ether' at usb-0000:00:1d.0-1.1, CDC Ethernet Device, 00:a0:c6:00:00:00 [ 198.076583] usbcore: registered new interface driver cdc_ether [ 198.955985] scsi 8:0:0:0: CD-ROM CWID USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2 [ 198.956797] scsi 8:0:0:1: Direct-Access ZTE MMC Storage 2.31 PQ: 0 ANSI: 2 I created the appropriate mobile broadband connection manually, but I cannot enable it in network manager, since the device is not recognized as mobile broadband. Any tips how to make it work?

  Read the article

• VMWare Workstation 8 can't find the headers directory

  - by BackSlash

  I'm having an issue with VMware Workstation 8. I installed it but when i run it, it shows this window: But, when I press on "Browse", this window comes up Even if I select the linux-headers-3.8.0-31-generic folder, it says that it can't find the C headers for that kernel. Why? P.S. I already tried sudo apt-get install linux-headers-3.8.0-31-generic and the terminal says that the kernel is up to date.

  Read the article

• No Android SDK, neither Java found

  - by Alex

  I have Java installed correctly, I did it by the manual http://www.wikihow.com/Install-Oracle-Java-on-Ubuntu-Linux I also installed Android SDK. However when I try to create a new Project IntelliJ Idea 12 and specify Project SDk choosing New - /home/alex/android-sdk-linux , it says me No Java SDK of appropriate version found. In addition to the Android SDK, you need to define a JSDK 1.5, 1.6 or 1.7 What did I miss?

  Read the article

• Installing ubuntuone

  - by bob

  Linux Mint 14 os I have tried to install ubuntu one onto the linux mint 14 through Synaptic package manager and software manager, both say its installed but when I go to find the programme its not there. installed as what Synaptic says........... ubuntuone client, ubuntuone client data, ubuntuone client gnome, ubuntuone control panel, what else is missing from this list please, it used to be so so easy to install but now, eeeek yours in advance Bob

  Read the article

• How to access files on a drive from an older system, mounted in a new system?

  - by David Thomas

  I've recently built a new system, after a rather large physical injury was sustained by my previous system (a precarious balance, and gravity, were not a happy mix). Surprisingly the /home drive of that system appears to have more-or-less survived the trauma. However... I decided to use a fresh drive for / (and swap) partition(s), and another fresh drive for the new /home. Now that's working, I decided to install the old /home drive (that I had assumed until now would be entirely dead and without capacity for use) into the new system to recover the files and data (so far as is possible). At this point I've run into a snag: I have no idea how to go about this (with Windows it was relatively easy, the new drive would be the latest character of the alphabet, and go from there). With 'disk utility' (System - Administration - Disk Utitlity) I've worked out which drive it is (/dev/sda) but clicking on 'mount' produces an error: 1: helper failed with: mount: according to mtab, /dev/sdb1 is already mounted on / mount failed ...if it is mounted on / I can't see it. I'm also moderately confused by the disk (device /dev/sda) being referred to as /dev/sdb1. Any and all insights would be incredibly welcome (I've already voted for: Idea #9063: New internal hard drives default automount at Brainstorm). Edited in response to Roland's request for a screenshot of disk utility: Details (so far as I know them): 40GB disk is / and swap, 1.0 TB Samsung is /home 1.0 TB Hitachi is from the old system (and was the old /home drive). Output from sudo fdisk -l pasted below: Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000bef00 Device Boot Start End Blocks Id System /dev/sda1 1 121601 976760001 83 Linux Disk /dev/sdb: 40.0 GB, 40018599936 bytes 255 heads, 63 sectors/track, 4865 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00037652 Device Boot Start End Blocks Id System /dev/sdb1 * 1 4742 38084608 83 Linux /dev/sdb2 4742 4866 993281 5 Extended /dev/sdb5 4742 4866 993280 82 Linux swap / Solaris Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e8d46 Device Boot Start End Blocks Id System /dev/sdc1 1 121602 976760832 83 Linux

  Read the article

• How can I install Adobe AIR?

  - by Vamsi Emani

  I am a heavy user of Tweetdeck and few other apps that are built on AIR. It appears that AIR has discontinued support for Linux. Even the older versions in the Adobe AIR Archives seem to support only 32 bit Linux distros and I am on 64 bit Oneiric currently. Is there even a slight possibility that I could run AIR in these conditions? If so, can you please tell me where can I get a detailed step by step installation for this?

  Read the article

• HP Deskjet D2680 Review

  <b>Linux and Whatever:</b> "The HP Deskjet D2680 is very easy to install in Linux. First I installed hplip and then I installed hplip-gui. After that it was as simple as plugging the printer in and then opening the HP device manager."

  Read the article

• Oracle Magazine, July/August 2008

  Oracle Magazine July/August features articles on business intelligence, Linux, green technology, Oracle OpenWorld, Oracle Advanced Compression, Oracle Total Recall, managing files, using database advisors, Linux kernel, page template consistency, handling exceptions, client result cache, and much more.

  Read the article

• TuxOnIce-problem: "CPU stuck for 22 s"

  - by Lester

  I use Ubuntu 12.04 LTS on a Lenovo Thinkpad T61 and am new to Linux. I installed TuxOnIce following this Guide. Actually it works but resuming takes very long. Shortly before resuming is complete I see some message flashing in command-line like "CPU stuck for 22 s". Some googling brought up pages like this but it did not help me solve me problem. I suppose being absolutely new to Linux is the biggest part of the problem.

  Read the article

• Recession? What Recession? Red Hat Continues to Grow

  <b>Linux Planet:</b> "Linux vendor Red Hat will report its fiscal 2010 numbers today. Virtualization, cloud services, middleware, a big win on the Tokyo Stock Exchange-- is Red Hat's future as rosy as it appears?"

  Read the article

• how to setup hive on a single node?

  - by Harman

  I successfully setup hadoop on ubuntu 10.04 on a single node by going through the steps mentioned in Michael Noll's tutorial ( Running Hadoop On Ubuntu Linux (Single-Node Cluster) ). Now, I'm trying to setup hive on the same machine but I'm stuck as of what to do after I decompress the hive-0.8.1-bin.tar.gz and move it to /usr/local/hive. Any help would be appreciated but as I'm new to Linux, it would be very helpful if someone could help me step-by-step.

  Read the article

• No network connectivity (not wired or wireless) - RT5390

  - by Ben Udy

  I am starting to think I simply need to accept a small loss and sell my new ASUS K73E. Because I really don't enjoy computing when I have to deal with Windough$ and this windows 7 64 bit on my new ASUS is even worse than the old machines with XP. I have written to ASUS and they simply say "We don't support Linux" and while Ralink's website says they do support Linux I can't get anyone to tell me what model Ralink card might be in my machine. Is anyone out there who might be able to give me some useful advice???? Here is the answer to command lspci nn && lsusb && lsmod && rfkill list all: di,snd_seq snd 54244 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device uvcvideo 57374 0 videodev 34361 1 uvcvideo v4l1_compat 13251 2 uvcvideo,videodev soundcore 6620 1 snd snd_page_alloc 7076 2 snd_hda_intel,snd_pcm psmouse 63677 0 serio_raw 3978 0 lp 7028 0 parport 32635 2 ppdev,lp fbcon 35102 71 tileblit 1999 1 fbcon font 7557 1 fbcon bitblit 4707 1 fbcon softcursor 1189 1 bitblit video 17375 0 output 1871 1 video vga16fb 11385 1 vgastate 8961 1 vga16fb ahci 32360 2 di,snd_seq snd 54244 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device uvcvideo 57374 0 videodev 34361 1 uvcvideo v4l1_compat 13251 2 uvcvideo,videodev soundcore 6620 1 snd snd_page_alloc 7076 2 snd_hda_intel,snd_pcm psmouse 63677 0 serio_raw 3978 0 lp 7028 0 parport 32635 2 ppdev,lp fbcon 35102 71 tileblit 1999 1 fbcon font 7557 1 fbcon bitblit 4707 1 fbcon softcursor 1189 1 bitblit video 17375 0 output 1871 1 video vga16fb 11385 1 vgastate 8961 1 vga16fb ahci 32360 2 Edit #2 lspci 00:00.0 Host bridge: Intel Corporation Device 0104 (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Device 0116 (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.5 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 6 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c49 (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 02:00.0 Network controller: RaLink Device 5390 03:00.0 Ethernet controller: Atheros Communications Device 1083 (rev c0) lsusb Bus 002 Device 002: ID 8087:0024 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 13d3:5710 IMC Networks Bus 001 Device 002: ID 8087:0024 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Thanks for the suggestion because this gave me a model for Ralink RT5390. I have now gone to Ralink.com and downloaded (via Windows 7) the driver package (it is a bz2 file). I hope I can figure out how to install it. And FYI - I was not able to run su (not authorized?) and dmidecode didn't exist (probably needs to be downloaded BUT no internet yet in Ubuntu)

  Read the article

• HDMI not detected Ubuntu 12.10 - ATI Radeon HD 6670

  - by Keith Wilson

  Brand new to Linux, so help a young blood out :-) (I'm a novice/hobby programmer, but completely new to Linux command syntax, etc) Brand new everything Rig. Fresh install of Ubuntu 12.10. Ubuntu installed everything and updates. I am getting VGA output and sound through standard sound port on mb. However the HDMI port on the radeon card is not recognized and not available. Any help getting this detected and usable?

  Read the article

• Blogging locally and globally–my experience

  - by DigiMortal

  In Baltic MVP Summit 2011 there was discussion about having two blogs - one for local and another for global audience – and how to publish once written information in these blogs. There are many ways how to optimize your blogging activities if you have more than one audience and here you can find my experiences, best practices and advices about this topic. My two blogs I have to working blogs: this one here technology and programming blog for local market My local blog is almost five years old and it makes it one of the oldest company blogs in Estonia. It is still active and I write there as much as I have time for it. This blog here is active since September 2007, so it is about 3.5 years old right now. Both of these blogs are  my major hits in my MVP carrier and they have very good web statistics too. My local blog My local blog is about programming, web and technology. It has way wider target audience then this blog here has. By example, in my local blog I blog also about local events, cool new concept phones, different webs providing some interesting services etc. But local guys can find there also my postings about how to solve one or another programming problem and postings about Microsoft technologies I am playing with. This far my local blog has a lot of readers for such a small country that Estonia is. This blog has made me a lot of cool contacts and I have had there a lot of interesting discussions about different technical topics. Why I started this blog? Living in small country is different than living in big country. In small country you have less people and therefore smaller audience so you have to target more than one technical topic to find enough readers. In a same time you are still interested in your main topics and you want to reach to more people who are sharing same interests with you. Practically one day y will grow out from local market and you go global. This is how this blog was born. Was it worth to create, promote and mess with it? Every second I have put on my time to this blog has been worth of it. Thanks to this blog I have found new good friends and without them I think it is more boring to work on different problems and solutions. Defining target audiences One thing you should always do when having more than one blog is defining target audiences. If you are just technomaniac interested in sharing your stuff and make some new friends and have something to write to your MVP nomination form then you don’t have to go through complex targeting process. You can do it simple way and same effectively. Here is how I defined target audiences to my blogs: local blog – reader of my local blog is IT professional, software developer, technology innovator or just some guy who is interested in technology,   this blog – reader of this blog is experienced professional software developer who works on Microsoft technologies or software developer who is open minded and open to new technologies and interesting solutions to development problems. You can see how local blog – due to small market with less people – has wider definition for audience while this blog is heavily targeted to Microsoft technologies and specially to software development. On practical side these decisions are also made well I think because it is very hard to build up popular common IT blog. On global level it is better to target some specific niche and find readers who are professionals on your favorite topics. Thanks to this blog I have found new friends who are professional developers and I am very happy about all the discussions I have had with them. Publishing content to different blogs My local blog and this blog have some overlapping topics like .NET, databases and SEO. Due to this overlapping there is question: when I write posting to my local blog then should I have to publish same thing in my global blog? And if I write something to my global blog then should I publish same thing also in my local blog? Well, it really depends on the definition of your target audiences. If they match then of course it is good idea to translate you post and publish it also to another blog. But if you have different audiences then you may need to modify your posting before publishing it. The questions you have to answer are: is target audience interested in this topic? is target audience expecting more specific and deeper handling of this topic or are they expecting more general handling of topic? is the problem you are discussing actual for target audience or not? You have to answer these questions and after that make your decision. If you need to modify your original posting then take some time and do it. Provide quality to all your readers because they will respect you if you respect them. Cross-posting and referencing It is tempting to save time that preparing some blog post takes and if you have are done with posting in one blog it may seem like good idea to make short posting to another blog and add reference to first one where topic is discussed longer. Well, don’t do it – all your readers expect good quality content from you and jumping from one blog post to another is disturbing for them. Of course, there is problem with differences between target audiences. You may have wider target audience and some people may be interested in more specific handling of topic. In this case feel free to refer your blog you are writing in english. This is not working very well in opposite direction because almost all my global blog readers understand english but not estonian. By example, estonian language is complex one and online translating tools make very poor translations from estonian language. This is why I don’t even plan to publish postings here that refer to my local blog for more information. I am keeping these two blogs as two different worlds and if there is posting that fits well to both blogs I will write my posting to one blog and then answer previous three questions before posting same thing to another blog. Conclusion Growing out of your local market is not anything mysterious if you are living in small country. As it is harder to find people there who are interested in same topics with you then sooner or later you will start finding these new contacts from global audience. Global audience is bigger and to be visible there you must provide high quality content to your audience. It is something you will learn over time and you will learn every day something new when you are posting to your global blog. You may ask: if global blog is much more complex thing to do then is it worth to do at all? My answer is: yes, do it for sure. It is not easy thing to do when you start but if you work on your global blog and improve it over time you will get over all obstacles pretty soon. Just don’t forget one thing – content is king and your readers expect high quality from you.

  Read the article

< Previous Page | 620 621 622 623 624 625 626 627 628 629 630 631  | Next Page >