Search Results

Search found 29437 results on 1178 pages for 'ubuntu membership'.

Page 628/1178 | < Previous Page | 624 625 626 627 628 629 630 631 632 633 634 635  | Next Page >

  • Cannot install "ATI/AMD proprietary FGLRX graphics driver" (SystemError)

    - by Fisherman John
    I have just installed a fresh copy of 12.04.1 64bit. I formatted my PC completely and enabled updates during the installation. After the installation was complete, I went on updating my software. However, when I wanted to install the additional drivers using the Additional Drivers tool (namely "ATI/AMD proprietary FGLRX graphics driver"), it gave me this error: SystemError: E:Unable to correct problems, you have held broken packages. The same error shows up if I try installing the post-release updates driver. Installing the drivers from the terminal results in this output: XXXXXX:~$ sudo apt-get install fglrx [sudo] password for XXXXX: Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: fglrx : Depends: lib32gcc1 but it is not going to be installed Depends: libc6-i386 but it is not going to be installed E: Unable to correct problems, you have held broken packages." I get this using "sudo apt-get update": http://pastebin.com/AWAtDXjY But "sudo apt-get install fglrx" still get me this error: http://pastebin.com/RYM55bVN & "sudo apt-get -f install fglrx" gives me this error: http://pastebin.com/xxekajvP Any help would be greatly appreciated. (Please note that I'm new to Linux, coming directly from Windows. I have tried Ubuntu twice or so before, but it was not for a long period of time. The drivers got installed smoothly the few times I've tried Ubuntu, but post-release updates never worked for me.) [I am going to work now, so I can only answer from my phone. Can't really test any new solutions you may give me until ~10 hours from now on. Maybe more.] @stonedsquirrel When I try to run that command, I get this error: "XXXXXX:~$ sudo apt-get install fglrx [sudo] password for XXXXX: Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: fglrx : Depends: lib32gcc1 but it is not going to be installed Depends: libc6-i386 but it is not going to be installed E: Unable to correct problems, you have held broken packages." ie. I get the same error. ( I am Fisherman John, dunno how to login & thereby respond to your comment again _ )

    Read the article

  • Why am I asked for default's keyring at startup?

    - by Nicoco
    I'm prompted for default's keyring at every boot since 11.10 upgrade, even though I don't see any application I have needing at startup (I have no wifi, and disabled gwibber-service) How can I know which application is requesting it ? How can I disable it ? I can't even move any window until I enter the password, and sometimes entering the password even crashes X (bug reported here : https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-input-evdev/+bug/882955)

    Read the article

  • Java command not found

    - by TonyMocha
    Follow the instruction to setup the java on ubuntu 11.10 from How to install Java?. Running following command to install: sudo apt-get install openjdk-6-jdk After it success, I type "java", it prompts me with this error: The program 'java' can be found in the following packages: * gcj-4.4-jre-headless * gcj-4.6-jre-headless * openjdk-6-jre-headless * gcj-4.5-jre-headless * openjdk-7-jre-headless

    Read the article

  • Upgrade from 11.04 to 11.10, getting "W:Failed to fetch gzip..."

    - by Michael Durrant
    Error during update A problem occurred during the update. This is usually some sort of network problem, please check your network connection and retry. W:Failed to fetch gzip:/var/lib/apt/lists/partial/us.archive.ubuntu.com_ubuntu_dists_oneiric_universe_i18n_Translation-en Encountered a section with no Package: header , E:Some index files failed to download. They have been ignored, or old ones used instead. I can browse web sites normally during this time though (my network is ok).

    Read the article

  • Partitioning a 128GB SSD and 500GB HDD

    - by Gladen
    So I have a 128GB SSD and 500GB HDD. I want to reïnstall my laptop and put Ubuntu 12.10 on this setup. I already looked around on the internet and came up with this partitioning schema: about 2GB of swap on the SSD (I got 4GB of RAM in my laptop) / using the rest of that space /home on the HDD So I was wondering, are there any better schemes or extra partitions that I should consider putting on a particular drive? Thanks in advance! :)

    Read the article

  • How can I add a new user as sudoer using the command line?

    - by David B
    After I add a user using adduser, I can't see it via System->Administration->Users and Groups unless I logout then login again. Is that normal? Also, can I set a newly added user as a sudoer or do I have to change that only after adding it? How can I do that via the shell? Finally, can I delete the original user that was created upon initial installation of ubuntu, or is this user somehow 'special'?

    Read the article

  • CONFIG_ATH_USER_REGD variable In Ununtu

    - by BigGenius
    There is a CONFIG_ATH_USER_REGD variable in OpenWrt that allows the user to override the default settings of the wireless NIC. Unfortunately grepping the Arch kernel config doesn't seem to have that, and since OpenWrt has its fair share of hacking and patches, I don't know if that's something they added or that's provided e.g. in compat-wireless. Does this setting exists for Ubuntu or BackTrack-Linux?

    Read the article

  • Adding custom applications to Gnome launcher

    - by Shaftoe2702
    Looking for a utility that allows me insert an item into the list of applications that GNOME knows about. For example: I have downloaded Eclipse EE (I have some very special plugins that I need to work with, and those plugins don't "like" the version available in the default repository). I'm using GNOME 3, on Ubuntu 11.10. So I want to execute Eclipse w/o opening a terminal and running it. It must be something very simple.

    Read the article

  • Rhythmbox - access Windows 7 Media Streaming

    - by rifferte
    I wish to be able to see and stream music to my Ubuntu 10.04 installation through Rhythmbox. I have enabled media streaming in Windows 7 and I can see Rhythmbox as an allowed device. I have installed the Coherence plugin for Rhythmbox. I can see my Windows 7 PC under the Shared folder in Rhythmbox, but I do not see any of my music. Is there a step along the way that I missed or something else that I have to enable?

    Read the article

  • Display system information

    - by Robottinosino
    I would like output akin to that of OSX's system_profiler (https://developer.apple.com/library/mac/#documentation/Darwin/Reference/ManPages/man8/system_profiler.8.html) On Ubuntu, I have to string a few utilities togeter: uname -a, lshw, ifconfig, etc... and then extract the list of installed software packages... Is there a single, simple facade to getting human readable system info from the CLI?

    Read the article

  • Booting problem with 12.04

    - by florent
    i do have a 12.04 ubuntu on my notebook , but i do have a problem with it. I cannot boot , if i dont press anything then there is a black screen , and it does not boot. If i press the space button , or any other key , for mutlitples times , like 20 or 25 times or more then it's boot in seconds , and normally. How can i resolve this? Thanks Ps:I do not have a problem with bios as it's already booting on first for the hard drive

    Read the article

  • Why df and du show different output

    - by Nischay
    When I execute command df -h /tmp it says disk utilization is 100% but when it tried du -sh /tmp it says disk utilization is 2%. I want to know why these commands shows different output and these two commands work and what is the solution of this problem. /var is installed on it own file system .I am using Ubuntu 12.04 server edition on my vps account.Due to this problem utilization of /tmp 100% according to df some programs complain about free space in /tmp.

    Read the article

  • Unsteady Display

    - by Elton McRae
    I use Ubuntu 12:04. The Text character on my screen while on the inter-net s too small, so I decided to adjust the display to give larger characters. This caused the screen to become very unstable, once I am logged it the screen begins to flitter. I am now usingthe guest login. How can I readjust the display to first make it stable and secondly to have larger text characters. thanks in anticipation, Elton.

    Read the article

  • Fans running very fast on MacBook Pro 8.1

    - by Tomasz Kacprzak
    I installed Ubuntu 12.04 on Macbook Pro 8.1 and one of the first things I noticed was that the fans were starting to spin very fast every few minutes for 10-30 sec and then going back to normal. That was happening even without any processor load, when completely idle. The fans were usually spinning at 4000 RPM and made much noise. The computer was not getting hotter than usual. When running OSX Lion there was no noise at all, fans almost all the time at 2000 RPM. I spent some time on it and found out that Precise uses a deamon to control the temperature, called macfanctld. You can use /etc/macfanctld.conf to set the configuration. I found out that the high fan speed is not due to the fact that the temperature is getting hot, but because there are two sensors which indicate wrong numbers (you can check that using 'sensors' command ): TW0P: +129.0°C TCTD: +256.0°C TCFC: +0.0°C TMBS: +0.0°C or setting the macfanctld log level to 2: Speed: 4992, *AVG: 56.9C, TC0P: 50.2C, TG0P: 51.5C, Sensors: TB0T:34 TB1T:34 TB2T:33 TC0C:58 TC0D:56 TC0E:59 TC0F:60 TC0P:50 TC1C:58 TC2C:58 TC3C:58 TC4C:57 TCFC:0 TCGC:57 TCSA:53 TCTD:256 TG0D:52 TG0P:52 THSP:42 TM0S:64 TMBS:0 TP0P:54 TPCD:60 TW0P:129 Th1H:51 Th2H:48 Tm0P:40 Ts0P:32 Ts0S:43 Moreover, TCTD was randomly jumping from temperatures of 0 to 256, so this may be the reason for unjustified random fan speeds. macfanctld is taking an average of the sensors including the values above, so the actual AVG temp used to control the fans is wrong, usually biased up, hence high RPM and noise. The workaround solution is to use an option in the macfanctld.conf which allows to ignore the malfunctioning sensors: exclude: 13 16 21 24 After reboot the reported temperatures are usually normal and the fans are working at reasonable speeds. I tested the response of the fans to heavy processor load by asking MATLAB to invert 10000x10000 matrix and the AVG temperature jumped to 63deg, and the fan to max 6200 RPM and then got it back to normal temperature. So I think it is safe so far. There is a expired bug about the failing sensor readings: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/955538 which may be good to open again. My question would be: does anyone know what the failing sensors do and if there is any danger in excluding them? Maybe some better solution to this problem?

    Read the article

  • Upgrade from 13.04 to 13.10 broke remote SSH access?

    - by stackoverflowuser95
    I can no longer connect via SSH to my Ubuntu instance after upgrading from 13.04 to 13.10 with: # do-release-upgrade Connecting with $ ssh -vvv [ip here] gives me: OpenSSH_6.3, OpenSSL 1.0.1e 11 Feb 2013 debug2: ssh_connect: needpriv 0 debug1: Connecting to [ip here] [[ip here]] port 22. debug1: connect to address [ip here] port 22: Connection timed out ssh: connect to host [ip here] port 22: Connection timed out So I tried uncommenting #PasswordAuthentication yes in /etc/ssh/sshd_config, and restarting with /etc/init.d/ssh restart; but there was no difference.

    Read the article

  • How to install MySQL 5.6?

    - by Ross Smith II
    I just installed Ubuntu 12.10 (amd64), and want to install a recent version of MySQL 5.6. If possible, I would like to install (not upgrade) it the "Debian Way' (i.e., using apt-get or dpkg). The only binaries I could find are here. Unfortunately, they are incomplete, as they only install files in /usr/share. If binaries aren't available, how could I install it from source, using the standard Debian method of installing from source. Thanks for any assistance.

    Read the article

  • Quickly package command fails

    - by Nick Lemaire
    I get an error when trying to package my quickly application: lemaire@laptop:~/Quickly/unity-bookmarks$ quickly package ........Ubuntu packaging created in debian/ ............An error has occurred during package building ERROR: package command failed Aborting It doesn't really give me an indication of what went wrong. It used to work before. If you need to take a look at the code: lp:~koukin/+junk/unity-bookmarks

    Read the article

  • YouTube, no video or sound

    - by Cautious1
    I tried the answers from previous posts without luck. I'm using ubuntu 10.04.4 and youtube shows a black screen, no video and no sound . I uninstalled adobe flash player closed down and reinstalled but it didn’t help. I have run Mint 13 on the same computer and it will play youtube without a problem. I'm not familier with linux language . Using comands in terminal might make everything terminal if I try!

    Read the article

  • NVIDIA Additional Drivers Empty - maximum resolution 640x480 - Driver disappears

    - by Hannibal
    EDIT: Optimus card. For resolution please read this thread: "You do not appear to be using the nvidia x server"(screenshot included) And this: Ubuntu 11.10 problem with Nvidia Thanks! I know, I know yet another NVIDIA question. So I did all the research. I uninstalled and installed nvidia-settings and drivers and nvidia-current from PPE repositories which are the most updated ones. I executed nvidia-xconfig. I have two major problems. One: Additional Drivers setting is empty! It doesn't contain any driver although one is installed. I have executed apt-get update too. But still the list is empty. Two: If I execute nvidia-xconfig it will properly configure an xorg.conf file. I restart but the maximum resolution I got is 640x480. I tried the xrandr but I can't add any resolution to display LVDS1. Some weird error occurs. So I can't add a proprietary driver and I can't boot in with the xorg file created by Nvidia... What can I do? With some work ( unistall nvidia-current and install libgl1-mesa-glx I was able to activate some kind of usage of my card because the resolution got better... and I added bumbelbee to because I have multiple video cards... ) but still the list is empty. I don't know what to do at this point??!!! Also: this is the most important part. When I first installed my ubuntu yesterday 11.10 one I saw the driver!! The driver was there... And then I ofc updated every package from internet.. And after that it was gone. And I can't bring it back. So there must be something wrong with one of the updates. But which???? Thanks for any extra info you can provide! I'm really desperate to solve this issue.

    Read the article

  • WMV will play audio but not show images (dark screen)

    - by GUI Junkie
    This happens on one computer. On the other computer I can see the video. I've installed GStreamer, FFMpeg and Ubuntu Restricted Extras. On the computer where it doesn't work, I've tried both Movie Player and VLC. There must be some difference between the two computers, but how can I obtain all the system information in such a way that a diff could be reasonably done? Or just any other suggestion on how to solve this would be appreciated. :-)

    Read the article

  • How do I use the Malayalam language in LibreOffice Writer?

    - by SAGAR
    I have installed Malayalam fonts from Software Center on my Ubuntu 13.04 installation. In LibreOffice Writer I can see the installed Malayalam fonts like Meera, Rachana. I would like to create a document in Malayalam fonts. I activated in in fonts selecting to Meera and Rachana, but when I type in document it's still English. I hope I haven't enabled some options I shouldn't have. Please guide me the right way to attain my requirement.

    Read the article

  • Scroll with Middle Click

    - by Anast
    Can i use the middle click mouse button so i can scroll down faster like windows? I mean when i am in windows and i press the middle click somewhere i can scroll in a 4 way pointer shows on the screen and when i move the mouse in any direction the window will scroll in that direction even without pressing the middle click. Is there anything like this in ubuntu? How can i do this esspecially in chrome!

    Read the article

  • Non-responsive mouse and keyboard fix

    - by JacobusR
    I'm using Ubuntu 12.10 and found that after about 20 minutes of work that my mouse and keyboard became very unresponsive. So I found the following fix: sudo -i To test if this is the problem: echo N> /sys/module/drm_kms_helper/parameters/poll To make the fix permanent: echo "options drm_kms_helper poll=N">/etc/modprobe.d/local.conf It appears that the fix does work, but what does this do? Am I breaking something else in doing this?

    Read the article

  • Which Folders To Include In backup?

    - by Jason
    I'm quite new to Ubuntu and want to create a backup. I'm really not sure what files and folders to include so that if I restore my system it will be as it is now. I can't seem to find good details of this anywhere. Hopefully someone could help me with this. Is it possible to backup everything as it is now so in the event of a system restore I don't have to reinstall programs and settings? Thanks, Jason

    Read the article

  • Laptop's battery is stuck on "estimating"?

    - by xd1936
    Hello! After installing Ubuntu 10.10, the battery indicator worked fine (both percent remaining and estimation on time). I then installed and configured some software (Skype, Pidgin, Thunderbird, removed Empathy and Evolution, ect) and the battery meter, when clicked, always says "(estimating...)" I've tried running the battery down to zero and charging it fully again. If I go into the history or details, the percentage is recorded correctly. Any ideas?

    Read the article

< Previous Page | 624 625 626 627 628 629 630 631 632 633 634 635  | Next Page >