Search Results

Search found 16472 results on 659 pages for 'computer scientist'.

Page 629/659 | < Previous Page | 625 626 627 628 629 630 631 632 633 634 635 636  | Next Page >

• GPU not powering on

  - by Lerp

  So I got home from work yesterday and went to turn my computer on as per usual to be greeted by this: The screens remained black, so I rebooted; I go as far as GRUB before my screens went black again. I rebooted again, they didn't turn on. I rebooted again, I got as far as the windows login screen. This time I unplugged it, opened it up and cleaned it but to no luck. The GPU was still being tempermental. I repeated the process of turning off and on several times until one time it work as normal. I happily played games for the rest of the night (5-6 hours?) thinking everything was jolly good now. Well I get home from work today and it is doing the SAME thing. Sometimes everything displays normally for a few seconds to minutes then the screens go black; then sometimes the screens don't come on at all. Summary and additional points Screens sometimes turn on before shortly turning off, sometimes they don't; I cannot seem to determine any pattern between when they do or do not turn off. The build has been working fine for about 8 months now so I know it's not hardware incompatibility. If I plug a monitor into the on board graphics I can use the PC normally (just in low graphics mode) I have two monitors and it's a case of they both turn on or not. So I think I can rule out the monitors being dead. I have tried replacing the GPU I have tried replacing the RAM I have tried flashing the CMOS I have tried cleaning the inside The GPU is a Radeon HD 7870 My questions Is my GPU dead? It's not very old and I would rather have a method of being certain it's the GPU before I fork out some money I can't really afford. I do not have a second PC here to test it in. If my GPU is dead why does it sometimes work and sometimes not? Update Okay, it was working again.. at least I thought it was. I left it running for 10-20minutes with the screens black. Turned it off and straight back on and it worked for all of 10minutes. I was then updating the post in joy thinking I could play some games for the rest of the night when BAM it went black again. So yeah, I don't know :C

  Read the article

• How do I (robustly) remotely execute tasks on Windows workstations in a domain?

  - by Zac B

  I'm not even sure if "robustly" is a word. Anyway. Context: We have a few hundred Windows 7 workstations on a LAN. We use AD/GPO management pretty heavily, but there are a lot of periodic and/or manual maintenance tasks we need to do that can't be done via GPO/scheduled task. For example, say I want to execute program X (which runs silently, in the background, and doesn't bother the user) on workstation Y, or say I want to execute task A on a workstation group B either on a schedule or on demand. Kicking the users off of their computers to do this (i.e. using RDP) is a no-no, and doesn't work on groups anyway. Question: What's the best way to do this that is robust enough that, after setup, I could give it to beginner support people (read: people who are phobic of the command line, and get confused with GUI interfaces more complicated than Firefox)? I'm a competent programmer, and, if there is a robust set of tools or framework out there for this type of task, I'd consider hacking something together myself if it didn't take too long. If there's some combination of tools or techniques that others use to make remote-workstation-administration doable by beginners, I have yet to find it. For those who care about the "why": I'm midlevel IT, and was told to implement a remote management solution that allows arbitrary/scheduled remote execution, with confirmation that programs actually ran remotely, and the ability to view what they returned. "Why?" I asked, "Can't I just use PsExec and the task scheduler on a dispatcher machine?" "No," I was told, "'Joe' the second-week tech is going to be in charge of this one, and he needs something simple with a GUI." What I've tried: I've played with making a bunch of one-clickable "transfer files to remote computer and run them with PsExec" batch/VB scrips, but those tend to break down and don't easily support running on customizable groups. I've played a little bit with the Windows version of Puppet, but it doesn't support arbitrary-time remote execution (it's ability to group computers into a tree/node structure is really nice though). I've used an older version of Altiris, and, while it does a lot of what I want, it's interface is awful, it's slow, crashes a lot, and is probably too expensive for management. SwiftWater's DMS solution does some of what I want, but it's very underdeveloped, closed-source (not a deal breaker but not ideal), and I get the impression that support and reliability are lacking.

  Read the article

• Windows7 issue in mutli- tasking and memory

  - by Nitesh

  I seeming some problem in my windows OS recently, let me first say my system configuration. processor - Intel(R) Core(TM)2 Quad CPU Q8400 @ 2.66 GHz Installed memory (RAM) - 4.00 GB (3.00 GB usable) System type - 32 bit operating system I am using two OS in this system, first one is Windows7 and the other is centOS. Well, I am using this from a long time there was no problem , and all of a sudden since from couple weeks I am facing problems in my Windows7 OS. In windows7 i was nearing using multiple jobs almost every time i log in, there was no problem but now i don't no what happen I am not able to do multiple jobs at same time. For example- 1 I am now not able to listen to music in windows media player and view photo's. All of a sudden the system stops working and does not respond and then respond after 5mins and the music get played where it got stopped after 5 mins. 2 When i start browersing internet it hangs all of sudden and doesn't respond for 2 or 3 mins and gets loading. I mean it just happens for every operation i do in the system. Even now typing was also difficult, it gets hanged very frequently even though i am doing single task. I have never come across this kind of problem before. So the first thing i did was to see the useage of the processor and the memory. Well, i thick the useage of the processor was fine, for single task the useage was some where around 3 to 5%. Well, it was something weird i found in the memory, in spite of no task that i was running it was using somewhere around 34 to 41% of memory. So i opened the task manager and click on resource monitor in performance tab. And in the memory section of the monitoring tool i found the usage of my RAM, it was something like this. Hardware reserved - 1029 MB In Use - 1430 MB Modified - 49 MB Standby - 1566 MB free - 22 MB And i could also see Available 1588 MB Cached 1615 MB Total 3067 MB Installed 4096 MB well, this if all i could find out and i have no idea why my computer is acting so weird all of a sudden and the performance problem is growing day by day and i also don't know if there is problem in Bios, i have let it for default settings from long time. please help me and Thank you in advance for reading this and helping me.

  Read the article

• Creating a network link between 2 very close buildings

  - by Daniel Johnson

  I have a charity who have two adjacent medium sized modern detached houses (in the UK): the buildings stand next to each other and are less than 5 metres apart. They have DSL connected to a single computer in one of the buildings. They want to add a network with wireless, and want it to work across both buildings. Being a charity they need to keep costs down. The network would be used for sharing Word documents, e-mail, browsing and skyping. My initial thoughts were to connect the buildings with fibre. So: Option 1 Use fibre between the buildings. Sufficient cable and two TP-LINK MC100CM Fast Ethernet Media Converters. Cost ~£80.00. But there is the extra cost and hassle of running the cable down and up the external walls, lifting and relaying paving, and burying underground. Never having fitted fibre I'm also a little worried about going up the wall and then bending the cable at 90 degrees to go through the wall and into the building. Option 2 Use two TP-Link TL-WA7510N High Powered Outdoor 5Ghz 15dBi Wireless antennas to connect the buildings. There is a clear line of sight at first floor level. Cost ~£100. And much easier to fit than fibre! Is using the TL-WA7510Ns overkill? Is there something more suitable? I had hoped to use some Netgear stuff, e.g. two DGN2200, one in each house and also use them to provide the wireless link between the buildings. However, in bridge mode wireless client association is not available and repeater mode with client association only supports WEP security which isn't strong enough. Is there something similar that would be up to the job? Option 3 Connect the buildings with UTP cable. My concerns here are risk of electric shock due to a difference of potential between the buildings (or are they so close this shouldn't be an issue) and protection from lightning strikes. Is fitting lighting arrestors expensive? And what can be done to ameliorate against the risk of shock? This all falls outside my area of expertise so I would really appreciate some advice.

  Read the article

• Why did Intel drop the Itanium?

  - by Cole Johnson

  I was reading up on the history of the computer and I came along the IA-64 (Itanium) processors. They sounded really interesting and I was confused as to why Intel would decide to drop them. The ability to choose explicitly what 2 instructions you wanted to run in that cycle is a great idea, especially when writing your program in assembly, for example, a faster bootloader. The hundreds of registers should be convincing for any assembly programmer. You could essentially store all the functions variables in the registers if it doesn't call any other ones. The ability to do instructions like this: (qp) xor r1 = r2, r3 ; r1 = r2 XOR r3 (qp) xor r1 = (imm8), r3 ; r1 = (imm8) XOR r3 versus having to do: ; eax = r1 ; ebx = r2 ; ecx = r3 mov eax, ebx ; first put r2 into r1 xor eax, ecx ; then set r1 equivalent to r2 XOR r3 or ; SAME mov eax, (imm32) ; first put (imm32) into r1 xor eax, ecx ; then set r1 equivalent to (imm32) XOR r3 I heard it was because of no backwards x86 comparability, but couldn't thy be fixed by just adding the Pentium circuitry to it and just add a processor flag that would switch it to Itanium mode (like switching to Protected or Long mode) All the great things about it would have surly put them a giant leap ahead of AMD. Any ideas? Sadly this means you will need a very advanced compiler to do this. Or even one per specific model of the CPU. (E.g. a newer version of the Itanium with an extra feature would require different compiler). When I was working on a WinForms (target only had .NET 2.0) project in Visual Studio 2010, I had a compile target of IA-64. That means that there is a .NET runtime that was able to be compiled for IA-64 and a .NET runtime means Windows. Plus, Hamilton's answer mentions Windows NT. Having a full blown OS like Windows NT means that there is a compiler capable of generating IA-64 machine code.

  Read the article

• Can't validate mine, sudo nor root in Debian "Jessie" Gnome anymore?

  - by Janar

  I'm Debian beginner & GUI guy in a bit of trouble? Can't login as sudo/gksu/root/su nor as (main/super)user after removed user password via Gnome-user-settings. History of actions (Probably irrelevant though) Installed Debian "Jessie" GNU/Linux with xFce GUI (en-US) as only OS. HardWare is ThinkPad w510. Skipped root user password in setup, to get sudo for superuser easily. Logged in (as always had) with Gnome (3.4.x), not once with xFCE. (installed Xfce. Installed xFce only to achieve more control (easier management) over packages this way, to set-up gnome much more by mine likes. Added more jessie repros (same ones as in Wheesy stable by default but for Jessie as, Jessie only had repros for security updates by default). Installed lots of gtk(3) & gnome(3) based soft; (- restarted again after this) Installed propietary graphics card driver for mine nvidia quadro. (- restarted once again after that one) Installed more stuff related to mine work/school/devel. The actual problem Had a plan to restart again, but wanted to set up auto-login first, instead set user password to none (don't ask why / perhaps caused by being awake for a looooong time), noticed it, and set also to auto-login, but couldn't undo mine previous mistake to create new password for me. As mine password is set to none I would have expected that simply return in pass prompt for emty password field would do, but it won't authenticate. I tried Alt+F2 "gksu gedit" as well as: sudo wget "https://www.some-page.eu/file.ext" and "su" in terminals, none has applied (quite logical actually - as I'm sudoer and highest ranked super user, besides only user in computer). Current stand Everything worked & still works nice after this accident, besides this password prompts part. To spoked to log-out nor restart. Synaptic package-manager is still open with root rights (only one, that has left open prior to the issue and not closed since, just in case). Goggled for help and read some manuals/faqs/how-tos - mostly lead to sudoers file management, but not found one specifically for mine issue - so still not any smarter. Really hope, that I don't have to redo OS inst all over again, by just one stupid mistake. Thanks for your reply :-)

  Read the article

• One user sometimes gets an unknown certificate error opening Outlook

  - by Chris

  Let me clarify a little. This isn't an unknown certificate error it's an unknown certificate error in so much as I can't figure out where the certificate comes from. This happens on a Win 7 Enterprise machine connecting to Exchange 2010 with Outlook 2010. The error he gets is that the root is not trusted because it's a self-signed cert. Take a look at this screenshot because even if I had generated this myself I wouldn't have put "SomeOrganizationalUnit" or "SomeCity" or "SomeState", etc. (Red block covers our domain name.) I'm a little concerned this is a symptom of a security breach. Exchange 2010 has three certificates installed but none of them are this certificate. They all have different expiration dates (one is expired) and different meta-data. edit: There are two scenarios that I see the certificate warning and one of them I can reliably repeat. When the user leaves his computer on over night Outlook pops the Security Warning window. I don't know what time this happens. Using Outlook Anywhere if I connect to Exchange externally via a cellular USB modem the Security Warning window will appear every time I close and reopen Outlook. Whether I say Yes or No does not make a difference on whether or not I can connect to Exchange and send/receive email. In other words, I can always connect to Exchange. I've checked my two Exchange servers and my Cisco router for a certificate that matches this one and I can't find it. edit 2: Here is a screenshot of the Security Alert window. (I've been calling it Security Warning... My mistake.) edit 3: I stopped seeing this error several weeks ago but I can't tie it to any single event (because I just sort of realized that warning had stopped showing up) but I think I found the source of the certificate. Last week I found out that the certificate on our website DomainA.com was invalid. I knew that our web admin had installed a valid certificate so when I look into the problem I found out I was being presented with the invalid certificate that this posting is in regards to. The Exchange server's domain is mail.DomainA.com so I can only guess that Outlook was passing this invalid certificate through as it did some kind of check on DomainA.com. This issue is still a mystery because the certificate warning stopped appearing several weeks ago whereas the invalid certificate issue on the website was only fixed last week. It ended up being a problem with the website control panel. The valid certificate was installed but not being served for some reason and instead the self-signed cert was being served.

  Read the article

• Is there a Distributed SAN/Storage System out there?

  - by Joel Coel

  Like many other places, we ask our users not to save files to their local machines. Instead, we encourage that they be put on a file server so that others (with appropriate permissions) can use them and that the files are backed up properly. The result of this is that most users have large hard drives that are sitting mainly empty. It's 2010 now. Surely there is a system out there that lets you turn that empty space into a virtual SAN or document library? What I envision is a client program that is pushed out to users' PCs that coordinates with a central server. The server looks to users just like a normal file server, but instead of keeping entire file contents it merely keeps a record of where those files can be found among various user PCs. It then coordinates with the right clients to serve up file requests. The client software would be able to respond to such requests directly, as well as be smart enough to cache recent files locally. For redundancy the server could make sure files are copied to multiple PCs, perhaps allowing you to define groups in different locations so that an instance of the entire repository lives in each group to protect against a disaster in one building taking down everything else. Obviously you wouldn't point your database server here, but for simpler things I see several advantages: Files can often be transferred from a nearer machine. Disk space grows automatically as your company does. Should ultimately be cheaper, as you don't need to keep a separate set of disks I can see a few downsides as well: Occasional degradation of user pc performance, if the machine has to serve or accept a large file transfer during a busy period. Writes have to be propogated around the network several times (though I suspect this isn't really much of a problem, as reading happens in most places more than writing) Still need a way to send a complete copy of the data offsite occasionally, and this would make it very hard to do differentials Think of this like a cloud storage system that lives entirely within your corporate LAN and makes use of your existing user equipment. Our old main file server is due for retirement in about 2 years, and I'm looking into replacing it with a small SAN. I'm thinking something like this would be a better fit. As a school, we have a couple computer labs I can leave running that would be perfect for adding a little extra redundancy to the system. Unfortunately, the closest thing I can find is Dienst, and it's just a paper that dates back to 1994. Am I just using the wrong buzzwords in my searches, or does this really not exist? If not, is there a big downside that I'm missing?

  Read the article

• What Sort of Server Setup Am I Likely to Need? - School A/V streaming

  - by DeathMagus

  My prior experience with servers has generally been limited to home file-sharing servers, low-traffic web-servers, and the like. This leaves me with the technical knowledge of how to set up a system, but little experience in terms of scaling said system. My current project, however, has me as the technical lead in setting up a school for online audio and video streaming. The difficulty I'm running into is that I don't quite have the experience to guess what they'll need, and they don't have the experience to tell me - so I've tried to ask as many pertinent questions about what they want to do with their server, and here's what I found out: About 1000 simultaneous users, and hoping to expand (possibly significantly) Both video and audio streaming, at obviously the highest quality possible Support for both live and playlist-based streaming. Probably only one channel, but as it's an educational opportunity, I imagine letting them have a few more wouldn't hurt. No word on whether they're locked into Windows or whether Linux is acceptable. Approximate budget - $7000. It may actually be about $2k less than this, because of a mishap with another technology firm (they ordered a $7000 DV tape deck for some reason, and now the company wants them to pay a 30% restocking fee). The tentative decisions I've already made: I'm planning on using Icecast 2 for my streaming server, fed by VLC Shoutcast encoding. Since the school already has a DMZ set up, I plan on placing the Icecast server in there, and feeding it through their intranet from a simple workstation computer in their studios. This system isn't in any way mission critical - it's an education tool (they're a media magnet school), so I figure redundancy is not worthwhile to them from a cost:benefit perspective. What I don't know is this: How powerful of a server will I need? What is likely to be my major throttle - bandwidth? How can I mitigate that? Will I need anything special for the encoding workstation other than professional video and audio capture cards and a copy of VLC? Are there any other considerations that I'm simply missing? Thanks a lot for any help - if there's more information you need, let me know and I'll tell you all I can.

  Read the article

• Creating a really public Windows network share

  - by Timur Aydin

  I want to create a shared folder under Windows (actually, Windows XP, Vista, and Win 7) which can be mounted from a linux system without prompting for a username/password. But before attempting this, I first wanted to establish that this works between two Windows 7 machines. So, on machine A (The server that will hold the public share), I created a folder and set its permissions such that Everyone has read/write access. Then I visited Control Panel - Network and Sharing Center - Advanced Sharing Settings and then selected "Turn off password protected sharing". Then, on machine B (The client that wants to access the public share with no username/password prompt), I tried to "map network driver" and I was immediately prompted by a password prompt. Some search on google suggested changing "Acconts: Limit local account use of blank passwords to console logon only" to "Disabled". Tried that, no luck, still getting username/password prompt. If I enter the username/password, I am not prompted for it again and can use the share as long as the session is active. But still, I really need to access the share without any username/password transaction whatsoever and this is not just a convenience related thing. Here is the actual reason: The device that will access this windows network share is an embedded system running uclinux. It will mount this share locally and then play media files. Its only user interface is a javascript based web page. So, if there is going to be any username/password transaction, I would have to ask the user to enter them over the web page, which will be ridiculously insecure and completely exposed to packet sniffing. After hours of doing experiments, I have found one way to make this happen, but I am not really very fond of it... I first create a new user (shareuser) and give it a password (sharepass). Then I open Group Policy Editor and set "Deny log on locally" to "A\shareuser". Then, I create a folder on A and share it so that shareuser has Read access to it. This way, shareuser cannot login to A, but can access the shared folder. And, if someone discovers the shareuser/sharepass through network sniffing, they can just access the shared folder, but can't logon to A. The same thing can be achieved by enabling the Guest user and then going to Group Policy Editor and deleting the "Guest" from the "Deny access to this computer from the network" setting. Again, Guest can mount the public share, but logging in to A as Guest won't be possible, because Guest is already not allowed to log in by default. So my question would be, how can I create a network share that is truly public, so that it can be mounted from a linux machine without requiring a password? Sorry for the long question, but I wanted to explain the reason for really needing this...

  Read the article

• Does 64bit Windows 8 have the same 75% memory-usage limitation for applications as Windows 7?

  - by Barleyman

  64bit Windows 7 (and Windows Vista) have a built-in limit of not being able to use the last 25% of RAM. You will get a low memory warning when you get close to the limit. Even if you disable that warning, applications will run out of memory and crash since the OS will refuse to allocate memory from that last 25%. That was fine when Vista was designed, when machines had 1 GB of total memory, but is pretty daft for today's 8 GB machines. Yes, the system will run cache, etc. on that extra 2 GB, but running out of memory when you have "merely" 2 GB left.... NB: this has nothing to do with the page file. If you limit the page file to a sensible size like 2 GB, you will still see this behavior. The system will cram the page file to the last byte while refusing to touch that 1/4th of the RAM. Does Windows 8 change this behavior? Is there now some fixed minimum free RAM requirement, like 512 MB, or is it still 25%? Can you actually adjust the low memory limit? EDIT: Here is another older post here which discusses this same behavior on Windows 7. There is fixed 25% limit in Windows 7 and I'd like to know if it's still in Windows 8. Windows 7 / Page File Disabled / 12 GB RAM / 2+ GB RAM free and "your computer is running low on memory" Edit2: Here is another link discussing the low memory warning and how to disable it. Note he claims the limit for RAM usage is 80%, not 75%. It would seem to be correct as you can in fact allocate 6.4GB of RAM with 8GB machine. Anything above and beyond that goes to the pagefile, though. http://halflight.com.au/2011/04/06/how-to-disable-low-memory-warnings-and-the-advantages-of-removing-the-page-file/ Edit3: a Here's couple of process explorer screenshots that demonstrate how it goes down. Exhibit1: https://dl.dropbox.com/u/42068601/sysinfo.jpg Exhibit2: https://dl.dropbox.com/u/42068601/sysint2.jpg You can see that Windows 7 will use the memory 6.4GB as the very last resort. I have low memory warning switched off here so programs crashed at the last screenshot allocation. With low memory warning turned on, it starts nagging before you can push OS to use that remaining 1.6GB. The question is not "Is it OK windows does not want to allocate last 20% of RAM because X", it's "Does Windows 8 still behave this way". With 16GB this really becomes dumb.

  Read the article

• Can Remote Desktop Services be deployed and administered by PowerShell alone, without a Domain in WIndows Server 2012 and 2012 R2?

  - by Warren P

  Windows Server 2008 R2 allowed deployment of Terminal Server (Remote Desktop Services) without a domain, and without any insistence on domains. This was very useful, especially for standalone virtual or cloud deployments of a server that is managed remotely for a remote client who has no need or desire for any ActiveDirectory or Domain features. This has become steadily more and more difficult as Microsoft restricts its technologies further and further in each Windows release. With Windows Server 2012, configuring licensing for Remote Desktop Services, is more difficult when not on a domain, but possible still. With Windows Server 2012 R2 (at least in the preview) the barriers are now severe: The Add/Remove Roles and Features wizard in Windows Server 2012 R2 has a special RDS deployment mode that has a rule that says if you aren't on a domain you can't deploy. It tells you to create or join a domain first. This of course comes in direct conflict with the fact that an Active Directory domain controller should not be the same machine as a terminal server machine. So Microsoft's technology is not such much a Cloud Operating System as a Cluster of Unwanted Nodes, needed to support the one machine I actually WANT to deploy. This is gross, and so I am trying to find a workaround. However if you skip that wizard and just go check the checkboxes in the main Roles/Features wizard, you can deploy the features, but the UI is not there to configure them, and when you go back to the RDS configuration page on the roles wizard, you get a message saying you can not administer your Remote Desktop Services system when you are logged in as a Local-Computer Administrator, because although you have all admin priveleges you could have (in your workgroup based system), the RDS configuration UI will not accept those credentials and let you continue. My question in brief is, can I still somehow, obtain the following end result: I need to allow 10-20 users per system to have an RDS (TS) session. I do not need any of the fancy pants RDS options, unless Microsoft somehow depends on those features being present. I believe I need the "RDS Session Host" as this is the guts of "Terminal Server". Microsoft says it is "full Windows desktop for Remote Desktop Services client. I need to configure licensing so that the Grace Period does not expire leaving my RDS non functional, so this probably means I need a way to configure TS CALs. If all of the above could technically be done with the judicious use of the PowerShell, I am prepared to even consider developing all the PowerShell scripts I would need to do the above. I'm not asking someone to write that for me. What I'm asking is, does anyone know if there is a technical impediment to what I want to do above, other than the deliberate crippling of the 2012 R2 UI for Workgroup users? Would the underlying technologies all still work if I manipulate and control them from a PowerShell script? Obviously a 1 word Yes or No answer isn't that useful to anyone, so the question is really, yes or no, and why? In the case the answer is Yes, then how.

  Read the article

• A gigabit network interface is CPU-limited to 25MB/s. How can I maximize the throughput?

  - by netvope

  I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? As a reference, the other computers in the network can usually transfer at 50+MB/s without problems. A computer with a Core 2 CPU generates only 5000 interrupts per second when it's transferring at 110MB/s. The number of interrupts is about 20 times less than the Atom system (if interrupts scale linearly with throughput.) And a minor question: How can I find out what is the driver in use for eth0?

  Read the article

• Educate me - should I buy these prebuilt NAS (which is better) or make my own?

  - by user29336

  I'm trying to learn as much as possible, and I think I've learned quite a bit so bear with me here under my confusion. I found a coupe NAS setups. I'm not sure if one is better than the other, other than the price being higher on some, and some coming with drives VS not. Let me list my setup so you can get an idea of what I want to provide: Macbook Pro Macbook Mini for Media streaming (so far) Windows 7 Gaming Computer Xbox 360 I'd like to provide a storage system for all these devices so they can access files very easily, I'd also like any of these devices to be able to stream media from this storage system. I'd like this storage system to be hassle free in terms of my confidence in the data integrity. If a drive fails, I want to know that I can replace the drive and all my files will still exist. I'd like to access this storage system OUTSIDE of my LAN. If I'm out on a job for work I'd like to go in, or be able to have people DL some files. This brings me to a question, is this what iSCSI is? I'd like this data system to be able to download torrents. I want to mount any drive on this storage system onto my OSX laptop as if it were a local drive attached. (Is this with iSCSI is?) I'd like this system to have a GOOD web based GUI. I don't want to install software to use it. I believe those are the most of my requirements. If I'm missing something that I have no knowledge about, can someone educate me? Here are the systems I found: $729ish on Newegg Lacie 5Big Network 2 (comes with 5TB of space. iSCSI / mac compatible, torrents, nice ui, + others?) Is this overpriced for what it provides? It almost seems like a great deal to me because of the 5TB of space it comes with vs the other NAS systems that don't come with storage but cost $600-700. Should I get a different NAS system? Netgear? Others? Do they have same features? Better? Is it better to buy your own disks? What about making my own? I'm tech savy all around. It seems cheaper to buy a premade one especially with the support/warranty it provides...

  Read the article

• Network Services disabled (not starting) on Windows XP

  - by Rickesh John

  I am currently running Windows XP Service Pack 3 on my system. But today, when I failed to connect to the internet, via a LAN cable, I realized that almost all of the vital network services had stopped functioning. Any attempts to start it through services.msc gives me the following message: Could not start the DNS Client Service on Local Computer Error 1068: The dependency service group failed to start All my software or services that are related to networking have stopped functioning, for example, Windows Firewall is turned off permanently, so is my Avast Anti-Virus' service of Real Time Shields and Web Shield. When I insert the LAN wire into my laptop, it registers itself, but this is what I get when I do a ping localhost C:>ping localhost Unable to contact IP driver, error code 2 Moveover, with ipconfig I get this : Windows IP Configuration An internal error occurred: The request is not supported. Please contact Microsoft Product Support Services for further help. Additional Information: Unable to query host name On some further poking around, I saw that none of the "NETWORK SERVICE" process in task manager, except svchost.exe were running. Also, when I first opened the task manager, I saw some 20 processes running with username column empty for most of them. With some search in Google, I found out that these services were important, DHCP DNS Net logon Network connection Network location Awareness TCP/IP Net BIOS Helper none of them, except Network Connections are working, they do not start. The event viewer of my system shows a bunch of 7000 and 7001 event errors. I have tried re installing the network driver, booting in safe mode with networking and tried to enable those services mentioned above. I had disabled System Restore some time back, so I have no restore points for my system. I tried a lot of things from Google searches but none of them worked. Also, with such a long list of issue, I am a little confused as to what should I search on the internet. :( One more thing I would like to mention, previous morning, my anti-virus Avast detected a RootKit buried deep in my system folders. It was removed, but maybe this was a problem caused by the root kit. I did run a boot-time scan but no viruses were found. Please please please advice. Is formatting and re-installation of Windows my only option?

  Read the article

• How to flip video feed that's presented upside down?

  - by Zuul

  Skype an other applications running under windows 7 Ultimate are presenting the video captured from the laptop built-in webcam upside down. I've tried many solution that I was able to find regarding issues like this, but to no avail. Some of the most relevant are discussed here: From Skype Support Network, the thread why is my video image of myself upside-down??? From ASUSTek Forums, the thread Built-in camera upside down Both present several potential solutions to this issue, but I've been unable to fix it for the laptop ASUS U6S. What I've already tried: Changing Drivers The driver that works must be the one from Windows, all others available from ASUS drivers either don't install or install but the webcam doesn't provide any video feed. This disallows all options that concern using an older driver or editing the .inf file as to manually adjust the settings. ASUS does not provide drivers for Windows 7, so I've used drivers from Windows Vista 32 Bit. Using the application manycam This application actually solves the issue (temporarily), but creates new ones: If I use the application to flip the video feed, Skype video call cease to work. This application doesn't save the settings, at least I wasn't able to find any way to save the settings I've used to flip the video feed. A computer restart brings all back to how it was, video feed upside down and if the application is still installed, Skype continues to fail on video calls. Regedit I've searched thru Windows Registry Editor as to find any reference to the webcam settings, hopping to find a key with the Flip parameter, since it's up to the driver to flip the image (by what I could ascertain from this problem). Couldn't find any reference to such settings, either they actually don't exist within the Windows Registry or they use some weird name that I could think off. System Configuration I was able to access the webcam system settings from the Windows Device Manager, but the tab that actually has the Image Rotation setting is always disabled. The same goes for the settings available from the Skype webcam options (that essentially is presenting the same settings as Windows Device Manager, just within a custom Skype pop-up). Question: How can I flip the video feed from the laptop's built-in webcam, as to properly see and broadcast the video?

  Read the article

• Sycronizing/deploying scripts across several systems

  - by otto

  I have a few time consuming tasks that I like to spread across several computers. These tasks require running an identical ruby or python script (or series of scripts that call each other) on each machine. The machines will a separate config file telling the script what portion of the task to complete. I want to figure out the best way to syncronize the scripts on these machines prior to running them. Up until now, I have been making changes to a copy of the script on a network share and then copying a fresh copy to each machine when I want to run it. But this is cumbersome and leaves a chance for error ( e.g missing a file on the copy or not clicking "copy and replace"). Lets assume the systems are standard windows machines that are not dedicated to this task and I don't need to run these scripts all the time (so I don't want a solution that runs 24/7 and always keeps them up to date, I'd prefer something that pushes/pulls on command). My thoughts on various options: Simple adaptation of my current workflow: Keep the originals on the network drive, but write a batch file that copies over the latest version of the scripts so everything is a one-click operation. Requires action on each system, but that's not the end of the world (since each one usually needs their configuration file changed slightly too). Put everything in a Mercurial/Git reposotory and pull a fresh copy onto each node. Going straight to the repo from each machine would guarantee a current version (and would have the fringe benefit of allowing edits to the script to be made from any machine). Cons would be that it requires VCS to be installed on each machine and there might be some pains dealing with authentication since I wouldn't use a public repo. Open up write access on a shared folder and write a script to use rsync (or similar) to push the changes out to all of the machines at once. This gets a current version on every machine (though you would have to change the script if you want to omit a machine or add a new one). Possible issue would be that each computer has to allow write access. Dropbox is a reasonable suggestion (and could work well) but I dont want to use an external service and I'd prefer not to have to have dropbox running 24/7 on systems that would normally not need it. Is there something simple that I am missing? Some tool designed expressly for doing this kind of thing? Otherwise I am leaning toward just tying all of the systems into Mercurial since, while it requires extra software, it is a little more robust than writing a batch file (e.g. if I split part of a script into a separate module, Mercurial will know what to do whereas I would have to add a line to the batch file).

  Read the article

• iTunes and Hulu Playback Choppy and Slow?

  - by Bart Silverstrim

  Specs: Windows XP, latest updates 1.7 ghz Pentium 4 1 gig ram DirectX 9.0c NVIDIA GeForce FX 5200 with 256 meg RAM OpenGL 2.1 The story: Okay, I had an older system laying around that I figured I would try turning into a mini-media system to connect to our TV. I put together a lot of older parts, got it into working order, etc. and hooked it up and voila'...slower, but usable system that displayed to the TV. It could run some things decently. I put in iTunes, it played video okay. Not great, but okay. Played Hulu and since we have a 1Mb download rate, the minimum for their site, there were some choppy moments when watching their shows, but I found that (sadly) changing resolution to 800x600 seemed to help with the issue when running full screen. I downloaded the application called Boxee and installed it. It wouldn't run; apparently the video card in the system supported OpenGL 1.2, and needed at least 1.4. I bought a cheap card, the 5200, with four times the memory in it and support for OpenGL 2.1. Installed, everything seemed fine. iTunes seemed to run fine, the video driver (PNY video card) came with OpenGL 2.1, and Boxee finally ran. I then upgraded to the latest drivers for the video card and ran the DirectX updater from MS. After that, the OpenGL Extension Viewer wouldn't run. It just stayed as an icon in the task bar. Also, any and all videos in iTunes stuttered and went out of sync horribly. Unwatchable. I tried watching Hulu video in Boxee, and it displayed video like it was a series of stills in a very bad powerpoint. Playing straightforward audio-only came through fine, no stutters no hiccups. I tried system restore to roll back updates to pre-directX updates (I thought that seemed to be the time that triggered the weird behavior), no joy. I tried uninstalling and reinstalling the video drivers. I installed updated audio drivers (ensoniq audiopci), nothing helped. I finally wiped the drive last night and tried reinstalling everything and restoring my iTunes content via an import from a backup. Fresh install, no updater on the video card or directx. the problem was still there although I haven't tested Hulu, the iTunes player is still stuttering like crazy if I play video, fine if I play audio. I know the processor isn't high in heft, but with one gig of RAM and the fact that it seemed to do okay before I thought that the problem must be software related. Has anyone else run into this sort of issue and have a solution other than "buy a new computer"? What specs seem to work with video at the low end for you? Right now the system is of little use other than keeping my music library and iTunes apps synced with my iPod.

  Read the article

• Wifi randomly drops on Windows 8 laptop

  - by JosiahS

  First of all, I did a lot of research on this problem, and I wasn't able to come to any helpful conclusion. I've finally decided that I need advice from those who might know where to look. So don't let me down. :P I used to have an older Windows 7 laptop, which worked great for basic office and web browsing. However, I wanted something that would play actual modern games. So I recently bought a Sager NP8235 with the Intel Wireless-AC 7260 wifi card, and installed Windows 8 Pro on it. And ever since, I've been having problems with the wifi. Generally, what happens is if I leave the laptop on but inactive for an extended amount of time (I've estimated it around an hour to two), the wifi will start dropping randomly. If I happened to have a download going at the time, it usually causes the download to fail. Or, if I put the laptop to sleep overnight, the next morning I usually have to restart the computer because the wifi device apparently stops working (it literally won't turn on). Also, and most frustrating, whenever I'm on a video chat (like Skype), after about ten minutes, the connection will start lagging like crazy, until it forces Skype to end the call. After that, I usually have to disable and reenable the wifi to get it working again. I know it isn't our internet, because all the other computers in our house (~8) don't have any issues. Even the old Windows 7 laptop (connected also over wifi) works just fine, scoring the normal ~3Mbps average on speedtest.net (yes, I know our internet is slow, we live out in the country). Additionally, when I connect the Sager directly to the router via ethernet, the internet instantly starts working just great. Like I said, I've done a lot of googling to figure out what's going on, and I haven't been able to find anything that worked for me. Is it Windows 8 conflicting with the Wifi drivers? As of this writing, I have the Intel drivers v16.1.5.2 installed (without the extra Intel software). Or is it our router? It's a TP-Link TL-WR841ND, set to the default settings. The Sager is currently being assigned to a static IP, if that makes any difference. And yet, the old windows 7 laptop has a much more stable connection than the Sager. Anyone have any ideas? At this point, I'd appreciate even knowing what the problem is.

  Read the article

• New harddrives failing within weeks.

  - by Jason Kealey

  I've experienced 8 hard disk failures in 3 months and have tried many things to solve the issue permanently but I have failed. I would like to know if you have any advice for me. System was running Win XP on an Asus P5W-DH Deluxe. I have setup a RAID-1 array. I started out with 2 x 500 GB 7200RPM Western Digital drives. One died. I took it out to RMA it. On the same day, the router was fried. Assumed a power surge occurred; connected an older UPS to protect the system. Once I got my hands on an identical disk, I installed it. The RAID array was rebuilt. A few days later, the other one died. Assumed the rebuild caused it to fail. Took it out for RMA. Before the other one arrived, the remaining one died. I then discovered I could re-enable them using the Intel Matrix Storage Manager. I re-enabled both and the system seemed fine for a week, until both died again. I got two new 1.5 TB 7200RPM Seagate drives and re-installed Windows 7. Also replaced the UPS and power supply. They both died again. The voltage on the plug is stable between 120 and 122V as per the UPS. None of the other devices have had any problems (monitors, etc.). At this point, I see two options: a) electrical issue in the house that was, for some reason, not blocked by the UPS. b) something else inside the system causing surges? motherboard? onboard raid controller? Failures happen fairly quickly, between 2 and 14 days after I fix the previous issue. I just gotten a new computer (Core i7) to replace it. If it is stable, I can determine that b) was the problem. If it fries its hard drive again, I can determine that it is an electrical issue in the house. Do you have any other thoughts? Any tools I can run on the drives that failed to get more information about the original SMART event history?

  Read the article

• Strange monitor issue - screen goes black after a few seconds

  - by Scott Szretter

  My LCD monitor display is going black (turning off). It's a Samsung SYncMaster 2233 widescreen. I am trying to figure out if there is anything I can do about it, or if the monitor is junk. I have tried multiple computers, all have the same issue. I have tried a different vga cable, same issue. Power and video cables are tight / double checked. When I power on the monitor, the blue light turns on at the bottom. Then a second or two later the video comes up as expected and it looks fine. However, about 2-3 seconds after that, the screen goes black. The blue light is still on and solid at the bottom (blue light normally flashes when the monitor is sleeping). If I power cycle the monitor, same thing happens. With no computer connected or when I unplug the vga cable, I see the searching for signal message "digital", then the screen goes black. However it usually shows "digital" then "analog" after that and switches between the two a few times. The buttons on the side do not do anything, although they may be, I just can not see if they are or not. I can usually get the "digital" message by pressing the buttons on the side, but then it quickly goes black again. What is really strange is sometimes I can get it to work fine. I am not sure what the difference is. Last week I connected it up and it worked fine and it stayed fine for at least a week! I did not turn it off or anything, I just let the OS put the display to sleep. Then this week one morning I started having the screen going black issue again. Seems like something is either loose inside or beginning to fail. Do you think there is any hope for it? update: pushing the input select button causes the "digital" and "analog" messages to flash on the screen, but only for a few seconds then it goes black. When it was working properly, those messages would flash back and fourth for probably 10-20 seconds then a message would show saying check input signal, but now just a black screen.

  Read the article

• git private server error: "Permission denied (publickey)."

  - by goddfree

  I followed the instructions here in order to set up a private git server on my Amazon EC2 instance. However, I am having problems when trying to SSH into the git account. Specifically, I get the error "Permission denied (publickey)." Here are the permissions of my files/folders on the EC2 server: drwx------ 4 git git 4096 Aug 13 19:52 /home/git/ drwx------ 2 git git 4096 Aug 13 19:52 /home/git/.ssh -rw------- 1 git git 400 Aug 13 19:51 /home/git/.ssh/authorized_keys Here are the permissions of my files/folders on my own computer: drwx------ 5 CYT staff 170 Aug 13 14:51 .ssh -rw------- 1 CYT staff 1679 Aug 13 13:53 .ssh/id_rsa -rw-r--r-- 1 CYT staff 400 Aug 13 13:53 .ssh/id_rsa.pub -rw-r--r-- 1 CYT staff 1585 Aug 13 13:53 .ssh/known_hosts When checking my logs in /var/log/secure, I used to get the following error message every time I tried to SSH: Authentication refused: bad ownership or modes for file /home/git/.ssh/authorized_keys However, after making a few permission changes, I no longer get this error message. Despite this, I am still getting the "Permission denied (publickey)." message every time I try to SSH. The command I am using to SSH is ssh -T git@my-ip. Here is the full log I get when I run ssh -vT [email protected]: OpenSSH_6.2p2, OSSLShim 0.9.8r 8 Dec 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: Connecting to my-ip [my-ip] port 22. debug1: Connection established. debug1: identity file /Users/CYT/.ssh/id_rsa type -1 debug1: identity file /Users/CYT/.ssh/id_rsa-cert type -1 debug1: identity file /Users/CYT/.ssh/id_dsa type -1 debug1: identity file /Users/CYT/.ssh/id_dsa-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.2 debug1: Remote protocol version 2.0, remote software version OpenSSH_6.2 debug1: match: OpenSSH_6.2 pat OpenSSH* debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr [email protected] none debug1: kex: client->server aes128-ctr [email protected] none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 08:ad:8a:bc:ab:4d:5f:73:24:b2:78:69:46:1a:a5:5a debug1: Host 'my-ip' is known and matches the RSA host key. debug1: Found key in /Users/CYT/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /Users/CYT/.ssh/id_rsa debug1: Trying private key: /Users/CYT/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey). I have spent a few hours going through threads on various sites, including SO and SF, looking for a solution. It seems that the permissions for my files are all okay, but I just can't figure out the problem. Any help would be greatly appreciated. Edit: EEAA: Here are the outputs you requested: $ getent passwd git git:x:503:504::/home/git:/bin/bash $ grep ssh ~git/.ssh/authorized_keys | wc -l grep: /home/git/.ssh/authorized_keys: Permission denied 0

  Read the article

• Recovering from backup without original install media

  - by KGendron

  A machine from my old job had a complete hard drive failure. I have backups but I'm running into severe problems restoring from them. The only install media was a secondary restore partition on the system's hard drive. I hate whoever came up with that idea more than i can possibly express with words. I spent several days trying to recover the disk - it is pretty well shot and none of my best tricks could even get it to show up in the bios/ The machine that broke is an hp with xp media center edition on it (I don't know why either). The backups were created using the default windows backup tool - I have .bfk file on an external hardrive that i am trying to restore from. I've replaced the hard drive. My home machine is running windows 7 64bit and i'm trying to use it as a platform to restore to the other disk. I downloaded the window 7 nt-restore utility, however no matter what i do it restores to my C drive rather than the specified drive. Fortunately win7 security settings prevented it from being a complete disaster - but still not a happy thing. I tried firing up the xp virtual machine. I can browse to the backups but it says they are invalid and refuse to let me view/ continue with the restore. I tried installing XP to an extra harddrive on my machine - however it bluescreens on me during the install process and I cry. I tried installing xp pro to the new drive and attempted to restore over it, it of course blackscreened on me as that was a stupid idea. I made two partitions on the new hard drive (Apparently the bios on this accursed piece of junk doesn't allow hd partitions larger than 200G anyways and thus fails 40 minutes into the install with an ever-descriptive "Disk Read Error". Guess how i spent last weekend? My last idea was to install xp pro to the second partition and then use it to restore from backup to the first. After the first restart it gives me the error "Windows could not start because of a computer disk hardware configuration problem. Could not read from the selected boot disk. Check boot path and disk hardware". My brain made one of those bad hard drive clicky noises. I've tried several boot disks but they don't seem to work. If anyone has a link to a good one it would be greatly appreciated. Anyone have any more ideas? - I really hate asking on what seems like such a simple issue but i am quite literally at my wit's end. Thanks - and sorry for the really long post.

  Read the article

• Windows 8 disk errors

  - by wrongusername

  So yesterday, I forcibly restarted my Windows 8 PC. VMWare Workstation was having some trouble with the guest Linux Mint OS. It wasn't responding for some time, so I tried suspending it September 28th or perhaps even before. It wouldn't suspend -- I forgot what the window looked like, but all options in the power menu were disabled (i.e. "Shutdown," "Power Off," and options like that were all disabled). I eventually killed the VMWare application through Task Manager, though I was too lazy to hunt down the running virtual machine itself, and decided to kill it by just shutting down my PC entirely. The PC wouldn't shut down for quite some time after the monitor went blank, so I did a cold reset by holding the power button. I then powered it on again and Windows briefly gave me some message like "Search for KERNEL_STACK_INPAGE_ERROR." Windows then started diagnosing some problems and gave me the message, "Repairing disk errors. This might take over an hour to complete." That was yesterday night, and I went to sleep without waiting for it to finish. This morning, it said that the repair failed, and that the log was at C:\windows\system32\LogFiles\srt\srtTrail.txt (as I remember it -- I don't have the exact path I wrote down right now). It gave me some other options to troubleshoot, such as resetting Windows (files and settings still intact, but programs not installed through the app store will be erased). That didn't work (no error message given, I was just told it didn't work). I tried rebooting in safe mode, the same diagnosis process begins, except that this time it doesn't bother with the automatic repairs again. So I tried using the command prompt to try to see if my files are at least still there. I was on the X drive, and I couldn't cd to the C drive. I couldn't find my folder under Users (of course?), and couldn't find the srt folder under LogFiles either. I am not sure what to try next. I have backed up everything, but to the cloud, so if absolutely necessary I can start off with a fresh copy of Windows and restore all my data, though it would be a hassle. Any thoughts on what might be wrong or what I can try? My computer was purchased just this June, so the hard drive should still be pretty new.

  Read the article

• Cannot access boot menu with compaq 8510p

  - by pinouchon

  I have a problem with my HP compaq 8510p laptop: when I start it, the fan starts and the power light is on, but the screen displays nothing. When I insert a bootable hard drive, it activates the hard drive light (meaning that the CD is recognized) but it stops after a few seconds. Same thing with any hard drive: the drive is recognized but does not boot. What I've tried so far: Changing the hard drive or booting with no hard drive (same problem) Plugging anoher display via VGA : no display on the other screen Inserting a windows-7 CD (same problem) Booting only on battery, with battery and power cable, only with power cable (same problem) So it looks like something is preventing the laptop from booting and displaying the boot menu. Do you have experienced something similar with a laptop ? What could be wrong ? The laptop is out of warranty. The system used to be windows-7 x64. Edit: I went to the help desk of my university. A guy took a look (he also tried to plug an external screen) and said that the computer is dead: on the HP laptops eventually the GPU card dies and so does the motherboard because they are linked. He saw this many times, and even if I can fix the problem, the laptop would crash again after a while. Do you have similar experience with HP laptops ? (mine is 4 years old) Edit 2: Believe it or not, my laptop is magically working again. I have no clue about what is going on. Now it is like starting and old car: when you turn it on you secretly hope it will actually start... With that said, I expect my laptop to break again in the near future (its an HP after all) and I will accept an answer or add my own accordingly. Edit 3: As expected, the laptop is down again. This time, sometimes when I power it up, it shuts down automatically after 3 seconds, sometimes not at all. In addition, when it does not shut down on its own, the power button does not work : the only way to shut it down is by unplugging the battery. As before, the screen is black, and only the power and battery lights are on. (the other ones: hard drive and wifi are off). I have tried to plug in another power plug, removing the battery and removing the hard drive without success. I might buy another laptop. I've brought the laptop to a repair shop. The problem is indeed that the graphic card is down. It will be replaced by a new one.

  Read the article

< Previous Page | 625 626 627 628 629 630 631 632 633 634 635 636  | Next Page >