Search Results

Search found 1575 results on 63 pages for 'lts'.

Page 63/63 | < Previous Page | 59 60 61 62 63 

• Everytime i am trying to connect to my box using SSH, its failing not connecting

  - by YumYumYum

  From any other PC doing SSH to my Ubuntu 11.10,is failing. My network setup: Telenet ISP (Belgium) Fiber cable < RJ45 cable straight to Ubuntu PC Even the SSH is running: Other PC: retrying over and over $ ping 192.168.0.128 PING 192.168.0.128 (192.168.0.128) 56(84) bytes of data. From 192.168.0.226 icmp_seq=1 Destination Host Unreachable From 192.168.0.226 icmp_seq=2 Destination Host Unreachable From 192.168.0.226 icmp_seq=3 Destination Host Unreachable From 192.168.0.226 icmp_seq=4 Destination Host Unreachable $ sudo service iptables stop Stopping iptables (via systemctl): [ OK ] $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] Connection closed by 192.168.0.128 $ ssh [email protected] [email protected]'s password: Connection closed by UNKNOWN $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host Follow up: -- checked cable -- using cable tester and other detectors -- no problem found in cable -- used random 10 cables -- adapter is not broken -- checked it using circuit tester by opening the system (card is new so its not network adapter card problem) -- leds are OK showing -- used LiveCD and did same ping test was having same problem -- disabled ipv6 100% to make sure its not the cause -- disabled iptables 100% so its also not the issue -- some more info $ nmap 192.168.0.128 Starting Nmap 5.50 ( http://nmap.org ) at 2012-06-08 19:11 CEST Nmap scan report for 192.168.0.128 Host is up (0.00045s latency). All 1000 scanned ports on 192.168.0.128 are closed (842) or filtered (158) Nmap done: 1 IP address (1 host up) scanned in 6.86 seconds ubuntu@ubuntu:~$ netstat -aunt | head Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN tcp 0 1 192.168.0.128:58616 74.125.132.99:80 FIN_WAIT1 tcp 0 0 192.168.0.128:56749 199.7.57.72:80 ESTABLISHED tcp 0 1 192.168.0.128:58614 74.125.132.99:80 FIN_WAIT1 tcp 0 0 192.168.0.128:49916 173.194.65.113:443 ESTABLISHED tcp 0 1 192.168.0.128:45699 64.34.119.101:80 SYN_SENT tcp 0 0 192.168.0.128:48404 64.34.119.12:80 ESTABLISHED tcp 0 0 192.168.0.128:54161 67.201.31.70:80 TIME_WAIT $ sudo killall dnsmasq -- did not solved the problem -- -- like many other Q/A was suggesting this same --- $ iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination $ netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 $ ssh -vvv [email protected] OpenSSH_5.6p1, OpenSSL 1.0.0j-fips 10 May 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 192.168.0.128 [192.168.0.128] port 22. debug1: Connection established. debug3: Not a RSA1 key file /home/sun/.ssh/id_rsa. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/sun/.ssh/id_rsa type 1 debug1: identity file /home/sun/.ssh/id_rsa-cert type -1 debug1: identity file /home/sun/.ssh/id_dsa type -1 debug1: identity file /home/sun/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: [email protected],[email protected],[email protected],[email protected],ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 118/256 debug2: bits set: 539/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: check_host_in_hostfile: host 192.168.0.128 filename /home/sun/.ssh/known_hosts debug3: check_host_in_hostfile: host 192.168.0.128 filename /home/sun/.ssh/known_hosts debug3: check_host_in_hostfile: match line 139 debug1: Host '192.168.0.128' is known and matches the RSA host key. debug1: Found key in /home/sun/.ssh/known_hosts:139 debug2: bits set: 544/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/sun/.ssh/id_rsa (0x213db960) debug2: key: /home/sun/.ssh/id_dsa ((nil)) debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/sun/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/sun/.ssh/id_dsa debug3: no such identity: /home/sun/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password: debug3: packet_send2: adding 64 (len 60 padlen 4 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). Authenticated to 192.168.0.128 ([192.168.0.128]:22). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env ORBIT_SOCKETDIR debug3: Ignored env XDG_SESSION_ID debug3: Ignored env HOSTNAME debug3: Ignored env GIO_LAUNCHED_DESKTOP_FILE_PID debug3: Ignored env IMSETTINGS_INTEGRATE_DESKTOP debug3: Ignored env GPG_AGENT_INFO debug3: Ignored env TERM debug3: Ignored env HARDWARE_PLATFORM debug3: Ignored env SHELL debug3: Ignored env DESKTOP_STARTUP_ID debug3: Ignored env HISTSIZE debug3: Ignored env XDG_SESSION_COOKIE debug3: Ignored env GJS_DEBUG_OUTPUT debug3: Ignored env WINDOWID debug3: Ignored env GNOME_KEYRING_CONTROL debug3: Ignored env QTDIR debug3: Ignored env QTINC debug3: Ignored env GJS_DEBUG_TOPICS debug3: Ignored env IMSETTINGS_MODULE debug3: Ignored env USER debug3: Ignored env LS_COLORS debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env USERNAME debug3: Ignored env SESSION_MANAGER debug3: Ignored env GIO_LAUNCHED_DESKTOP_FILE debug3: Ignored env PATH debug3: Ignored env MAIL debug3: Ignored env DESKTOP_SESSION debug3: Ignored env QT_IM_MODULE debug3: Ignored env PWD debug1: Sending env XMODIFIERS = @im=none debug2: channel 0: request env confirm 0 debug1: Sending env LANG = en_US.utf8 debug2: channel 0: request env confirm 0 debug3: Ignored env KDE_IS_PRELINKED debug3: Ignored env GDM_LANG debug3: Ignored env KDEDIRS debug3: Ignored env GDMSESSION debug3: Ignored env SSH_ASKPASS debug3: Ignored env HISTCONTROL debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env GDL_PATH debug3: Ignored env GNOME_DESKTOP_SESSION_ID debug3: Ignored env LOGNAME debug3: Ignored env QTLIB debug3: Ignored env CVS_RSH debug3: Ignored env DBUS_SESSION_BUS_ADDRESS debug3: Ignored env LESSOPEN debug3: Ignored env WINDOWPATH debug3: Ignored env XDG_RUNTIME_DIR debug3: Ignored env DISPLAY debug3: Ignored env G_BROKEN_FILENAMES debug3: Ignored env COLORTERM debug3: Ignored env XAUTHORITY debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel_input_status_confirm: type 99 id 0 debug2: PTY allocation request accepted on channel 0 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_status_confirm: type 99 id 0 debug2: shell request accepted on channel 0 Welcome to Ubuntu 11.10 (GNU/Linux 3.0.0-12-generic x86_64) * Documentation: https://help.ubuntu.com/ 297 packages can be updated. 92 updates are security updates. New release '12.04 LTS' available. Run 'do-release-upgrade' to upgrade to it. Last login: Fri Jun 8 07:45:15 2012 from 192.168.0.226 sun@SystemAX51:~$ ping 19<--------Lost connection again-------------- Tail follow: -- dmesg is showing a very abnormal logs, like Ubuntu is automatically bringing the eth0 up, where eth0 is getting also auto down. [ 2025.897511] r8169 0000:02:00.0: eth0: link up [ 2029.347649] r8169 0000:02:00.0: eth0: link up [ 2030.775556] r8169 0000:02:00.0: eth0: link up [ 2038.242203] r8169 0000:02:00.0: eth0: link up [ 2057.267801] r8169 0000:02:00.0: eth0: link up [ 2062.871770] r8169 0000:02:00.0: eth0: link up [ 2082.479712] r8169 0000:02:00.0: eth0: link up [ 2285.630797] r8169 0000:02:00.0: eth0: link up [ 2308.417640] r8169 0000:02:00.0: eth0: link up [ 2480.948290] r8169 0000:02:00.0: eth0: link up [ 2824.884798] r8169 0000:02:00.0: eth0: link up [ 3030.022183] r8169 0000:02:00.0: eth0: link up [ 3306.587353] r8169 0000:02:00.0: eth0: link up [ 3523.566881] r8169 0000:02:00.0: eth0: link up [ 3619.839585] r8169 0000:02:00.0: eth0: link up [ 3682.154393] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 3899.866854] r8169 0000:02:00.0: eth0: link up [ 4723.978269] r8169 0000:02:00.0: eth0: link up [ 4807.415682] r8169 0000:02:00.0: eth0: link up [ 5101.865686] r8169 0000:02:00.0: eth0: link up How do i fix it? -- http://ubuntuforums.org/showthread.php?t=1959794 $ apt-get install openipml openhpi-plugin-ipml $ openipmish > help redisp_cmd on|off > redisp_cmd on redisp set Final follow up: Step 1: BUG for network card driver r8169 Step 2: get the latest build version http://www.realtek.com/downloads/downloadsView.aspx?Langid=1&PNid=4&PFid=4&Level=5&Conn=4&DownTypeID=3&GetDown=false&Downloads=true#RTL8110SC(L) Step 3: build / make $ cd /var/tmp/driver $ tar xvfj r8169.tar.bz2 $ make clean modules && make install $ rmmod r8169 $ depmod $ cp src/r8169.ko /lib/modules/3.xxxx/kernel/drivers/net/r8169.ko $ modprobe r8169 $ update-initramfs -u $ init 6 Voila!!

  Read the article

• Why Wifi no longer works 12.04.1

  - by Roger

  starting this morning over wifi (Realtek RTL8188CE) on CLEVO W253HU. May be due to the update before yesterday, more pilot managed, but somehow it worked yesterday. If someone has an idea of the problem. Back command lines: cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.1 LTS" lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 006: ID 192f:0416 Avago Technologies, Pte. Bus 002 Device 004: ID 5986:0315 Acer, Inc lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) 03:00.0 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05) 03:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 90) 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 90) 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 90) lspci -nn | grep -i net 02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) 03:00.0 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 05) lspci -k 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: i2c-i801 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device 9196 Kernel modules: rtl8192ce 03:00.0 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: jme Kernel modules: jme 03:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: sdhci-pci Kernel modules: sdhci-pci 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: sdhci-pci 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: jmb38x_ms Kernel modules: jmb38x_ms sudo lshw -C network *-network NON-RÉCLAMÉ description: Network controller produit: RTL8188CE 802.11b/g/n WiFi Adapter fabriquant: Realtek Semiconductor Co., Ltd. identifiant matériel: 0 information bus: pci@0000:02:00.0 version: 01 bits: 64 bits horloge: 33MHz fonctionnalités: pm msi pciexpress cap_list configuration: latency=0 ressources: portE/S:e000(taille=256) mémoire:f7d00000-f7d03fff *-network description: Ethernet interface produit: JMC250 PCI Express Gigabit Ethernet Controller fabriquant: JMicron Technology Corp. identifiant matériel: 0 information bus: pci@0000:03:00.0 nom logique: eth0 version: 05 numéro de série: 00:90:f5:c1:c6:45 taille: 100Mbit/s capacité: 1Gbit/s bits: 32 bits horloge: 33MHz fonctionnalités: pm pciexpress msix msi bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=jme driverversion=1.0.8 duplex=full ip=192.168.1.54 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s ressources: irq:44 mémoire:f7c20000-f7c23fff portE/S:d100(taille=128) portE/S:d000(taille=256) mémoire:f7c10000-f7c1ffff mémoire:f7c00000-f7c0ffff lsmod Module Size Used by btusb 18288 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 11 btusb,rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 binfmt_misc 17540 1 snd_hda_codec_realtek 224173 0 dm_crypt 23125 0 snd_hda_codec_hdmi 32474 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev snd_hda_intel 33773 2 snd_hda_codec 127706 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi jmb38x_ms 17646 0 psmouse 87692 0 serio_raw 13211 0 memstick 16569 1 jmb38x_ms snd_seq_midi_event 14899 1 snd_seq_midi rtl8192ce 84826 0 rtl8192c_common 75767 1 rtl8192ce rtlwifi 111202 1 rtl8192ce snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq mac80211 506816 3 rtl8192ce,rtl8192c_common,rtlwifi mac_hid 13253 0 snd 78855 14 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device cfg80211 205544 2 rtlwifi,mac80211 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp usbhid 47199 0 hid 99559 1 usbhid i915 473035 3 drm_kms_helper 46978 1 i915 drm 242038 4 i915,drm_kms_helper jme 41259 0 i2c_algo_bit 13423 1 i915 sdhci_pci 18826 0 sdhci 33205 1 sdhci_pci wmi 19256 0 video 19596 1 i915 iwconfig lo no wireless extensions. eth0 no wireless extensions. ifconfig eth0 Link encap:Ethernet HWaddr 00:90:f5:c1:c6:45 inet adr:192.168.1.54 Bcast:192.168.1.255 Masque:255.255.255.0 adr inet6: fe80::290:f5ff:fec1:c645/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:4513 erreurs:0 :0 overruns:0 frame:0 TX packets:4359 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:3471675 (3.4 MB) Octets transmis:712722 (712.7 KB) Interruption:44 lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:16436 Metric:1 Packets reçus:686 erreurs:0 :0 overruns:0 frame:0 TX packets:686 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 Octets reçus:64556 (64.5 KB) Octets transmis:64556 (64.5 KB) sudo iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. uname -r -m 3.2.0-30-generic x86_64 cat /etc/network/interfaces auto lo iface lo inet loopback nm-tool NetworkManager Tool State: connected (global) - Device: eth0 [Connexion filaire 1] ------------------------------------------ Type: Wired Driver: jme State: connected Default: yes HW Address: 00:90:F5:C1:C6:45 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.54 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 sudo rfkill listrfkill list 1: hci0: Bluetooth Soft blocked: no Hard blocked: no The absence of line "Kernel driver in use:" the return of lspci-k made ??me think that it is not loaded yet but he seems to be. lsmod | grep rtl8192ce rtl8192ce 137478 0 rtlwifi 118749 1 rtl8192ce mac80211 506816 2 rtl8192ce,rtlwifi I found something disturbing in / var / log / syslog Sep 14 11:40:11 pcroger kernel: [ 64.048783] rtl8192ce-0:rtl92c_init_sw_vars():<0-0> Failed to request firmware! Sep 14 11:40:11 pcroger kernel: [ 64.048795] rtlwifi-0:rtl_pci_probe():<0-0> Can't init_sw_vars. Sep 14 11:40:11 pcroger kernel: [ 64.048835] rtl8192ce 0000:02:00.0: PCI INT A disabled Sep 14 11:40:11 pcroger kernel: [ 64.943345] ata1.00: exception Emask 0x0 SAct 0x7fffffff SErr 0x0 action 0x6 frozen Sep 14 11:40:11 pcroger kernel: [ 64.943358] ata1.00: failed command: READ FPDMA QUEUED Sep 14 11:40:11 pcroger kernel: [ 64.943371] ata1.00: cmd 60/00:00:00:68:6a/04:00:0b:00:00/40 tag 0 ncq 524288 in Sep 14 11:40:11 pcroger kernel: [ 64.943374] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) Sep 14 11:40:11 pcroger kernel: [ 64.943381] ata1.00: status: { DRDY } Ubuntu and takes forever to start (2 min).

  Read the article

• Ubuntu 12.04 does not see windows already install on my computer (dual installation)

  - by jacinta

  I was trying to install the ubuntu 12.4 along side windows 7 on my new HP Pavilion 64k desktop with windows 7 computer but Ubuntu said that ( This computer has no detected operating system) and some one said (I suggest you chkdsk your Windows partition. I also suggest you resize the NTFS in WIndows then install Ubuntu to the free space.) Therefore I did (To shrink a simple or spanned volume using the Windows interface In Disk Management, right-click the simple or spanned volume you want to shrink. Click Shrink Volume…. Follow the instructions on your screen.) Then When I try to install ubuntu 12.4 after doing this, I received the same error. I was going to undo what I did but I see that I lose 1g when I do that so now what do I do? it says I can do a new simple volume and maybe then the space will no longer be unallocated. Please help me. I think I have a bad cd (ubuntu 12.4) cause from my research I see that I am not suppose to get a screen saying that (The computer has no detected operating system) I think this is a bad cd and I hope I did not mess up my computer. Please help. .................................................................................... O k I think I am following what you said about how to edit my question irrational john. I did chkdsk as you and actionparsnip (andrew-woodhead666) told me to AND ALSO did a lot of other things before I found out how to chkdsk. No problems. Thank you. Then I put back the space (extended) I took from system. I still was only able to put back 15 and not 16 so it is up to 99mb not back to 100mb. Then I shrank HP (C) as you told me, to 10 13,240 mb which is (12.93gb Unallocated). I did not change it into NTSF by doing the (New Simple Volume Action) I just left it. Then I tried to install UBUNTU 12.04 live CD amd64 and it gave me the results it was sometimes giving me before which is result (THAT Ubuntu) does not tell me weather I have or have not an already installed windows7. It just goes to a window that would have showed me information on what I have and on the bottom (DEVICE FOR BOOT LOADER INSTALLATION /dev/sda ) and the option to go BACK, QUIT, or INSTALL. (I think it is the INSTALLATION TYPE window). Therefore I do what I have been doing and I QUIT. What do I do now? Sorry that it seems like I cannot do anything on my own. On the Youtube video how to install ubuntu dual-boot alongside windows UBUNTU is installed so easy. The installation option page gives 3 options including dual instillation and the disk even lets you use a slider to slide to the size of the partition size you want. Yet my UBUNTU live cd is a mess and I checked it as one of you guys told me and got back information that it is good. Oh well this guy says you should press a control key to tell which device you are using to install ubuntu before the screen comes up. I guess cause it is old. This page also shows you easy stuff that do not show up on my cd. how to dual-boot UBUNTU and windows 7 P.S.. I saw this on the windows 7 website windows.microsoft.com/en-US/windows7/Formatting-disks-and-drives-frequently-asked-questions CREATE A BOOT PARTITION I HAD TO LEAVE OUT THE HTTP STUFF CAUSE I AM ONLY ALLOWED 2 ON A PAGE IT SAID To create a boot partition Warning Warning If you are installing different versions of Windows, you must install the earliest version first. If you don't do this, your computer may become inoperable. Open Computer Management by clicking the Start button Picture of the Start button, clicking Control Panel, clicking System and Security, clicking Administrative Tools, and then double-clicking Computer Management.? Administrator permission required If you're prompted for an administrator password or confirmation, type the password or provide confirmation. In the left pane, under Storage, click Disk Management. Right-click an unallocated region on your hard disk, and then click New Simple Volume. In the New Simple Volume Wizard, click Next. Type the size of the volume you want to create in megabytes (MB) or accept the maximum default size, and then click Next. Accept the default drive letter or choose a different drive letter to identify the volume, and then click Next. In the Format Partition dialog box, do one of the following: If you don't want to format the volume right now, click Do not format this volume, and then click Next. To format the volume with the default settings, click Next. For more information about formatting, see Formatting disks and drives: frequently asked questions. Review your choices, and then click Finish. AND THIS ON ANOTHER PAGE. Formatting disks and drives: frequently asked questions Hard disks, the primary storage devices on your computer, need to be formatted before you can use them. When you format a disk, you configure it with a file system so that Windows can store information on the disk. Hard disks in new computers running Windows are already formatted. If you buy an additional hard disk to expand the storage of your computer, you might need to format it. Storage devices such as USB flash drives and flash memory cards usually come preformatted by the manufacturer, so you probably won't need to format them. CDs and DVDs, on the other hand, use different formats from hard disks and removable storage devices. For information about formatting CDs and DVDs, see Which CD or DVD format should I use? Warning Warning Formatting erases any existing files on a hard disk. If you format a hard disk that has files on it, the files will be deleted. WHAT I DID WAS I GOT TO COMPUTER MANAGEMENT SECTION THEN I CLICKED ON DRIVE HP(C) (it put stripes on to show it is selected) Then I click on ACTION selected ALL TASKS AND THEN selected SHRINK VOLUME and then chose how much space from what it was giving me that I wanted. (12.93gb) AND THAT WAS ALL I DID. THEN I TRIED TO INSTALL UBUNTU i NEVER GOT THE 3RD SCREEN THAT IS IN THE VIDEO I INCLUDED (THE YOUTUBE WITH THE ENGLISH GUY) INSTALLATION TYPE I ALSO DID NOT GET THE 4TH SCREEN THAT ALLOWS YOU TO SELECT PARTITION SIZE what i got next was the 2nd INSTILLATION TYPE window shown on the (LINUX BS DOS.COM) PAGE THAT I INCLUDED and it showed no information about any drives (no drives /partition or stuff was shown) only the Boot Loader statement and the dev/sda bar and that's why i did not press install but chose to QUIT. SORRY I JUST NOW SAW YOUR ANSWER IRRATIONAL JOHN. I SHRANK HP(C) BY 12.93GB MY UNALLOCATED SPACE IS NOW 12.93GB HP(C) = 907.17gb NTSF...YOU ARE CORRECT WITH EVERYTHING YOU SAID This is what i read on (http://)windows.microsoft.com/en-US/windows7/Create-a-boot-partition I am only allowed 2 links Create a boot partition You must be logged on as an administrator to perform these steps. A boot partition is a partition that contains the files for the Windows operating system. If you want to install a second operating system on your computer (called a dual-boot or multiboot configuration), you need to create another partition on the hard disk, and then install the additional operating system on the new partition. Your hard disk would then have one system partition and two boot partitions. (A system partition is the partition that contains the hardware-related files. These tell the computer where to look to start Windows.) To create a partition on a basic disk, there must be unallocated disk space on your hard disk. With Disk Management, you can create a maximum of three primary partitions on a hard disk. You can create extended partitions, which include logical drives within them, if you need more partitions on the disk. Picture of disk space in Computer ManagementUnallocated disk space If there is no unallocated space, you will either need to create space by shrinking or deleting an existing partition or by using a third-party partitioning tool to repartition your hard disk. For more information, see Can I repartition my hard disk? To create a boot partition Warning Warning If you are installing different versions of Windows, you must install the earliest version first. If you don't do this, your computer may become inoperable. Open Computer Management by clicking the Start button Picture of the Start button, clicking Control Panel, clicking System and Security, clicking Administrative Tools, and then double-clicking Computer Management.? Administrator permission required If you're prompted for an administrator password or confirmation, type the password or provide confirmation. In the left pane, under Storage, click Disk Management. Right-click an unallocated region on your hard disk, and then click New Simple Volume. In the New Simple Volume Wizard, click Next. Type the size of the volume you want to create in megabytes (MB) or accept the maximum default size, and then click Next. Accept the default drive letter or choose a different drive letter to identify the volume, and then click Next. In the Format Partition dialog box, do one of the following: If you don't want to format the volume right now, click Do not format this volume, and then click Next. To format the volume with the default settings, click Next. For more information about formatting, see Formatting disks and drives: frequently asked questions. Review your choices, and then click Finish. I did what you told me @irrational john and this is the screen shot. I ENTERED ubuntu@ubuntu:~$ sudo os-prober computer did not respond so I entered ubuntu@ubuntu:~$ sudo apt-get -y remove dmraid computer responded with Reading package lists... Done Building dependency tree Reading state information... Done The following packages will be REMOVED: dmraid 0 upgraded, 0 newly installed, 1 to remove and 0 not upgraded. After this operation, 141 kB disk space will be freed. (Reading database ... 147515 files and directories currently installed.) Removing dmraid ... update-initramfs is disabled since running on read-only media Processing triggers for man-db ... I entered ubuntu@ubuntu:~$ sudo os-prober Computer Responded with /dev/sda1:Windows 7 (loader):Windows:chain /dev/sda3:Windows Recovery Environment (loader):Windows1:chain ubuntu@ubuntu:~$ ............... @obsessiveFOSS I don't know what is a Grub menu and I do not know what is the Ubuntu boot option The answer you gave to me was correct. This one {This apparently removes the dmraid metadata. After doing that, you can use the desktop icon Install Ubuntu 12.04 LTS to start the Ubuntu installer. This time the Installation Type window should contain the option to Install Ubuntu alongside Windows 7.} This is what I decided to do. I did not see the rest of your help 'till now. Never the less. I think the best thing for me to do now is to get a cheap used laptop and either do a dual installation or just install Ubuntu on to it. This way if I have any issues that I cannot solve like the one I had here, at least I will still have a usable computer to work on and to use to get answers with because I am not an expert like the people on this forum. Thanks a lot I will try to keep learning and do research enough to some day help someone else.

  Read the article

• Building LMMS: "Configuring incomplete, errors occurred!"

  - by fridojet

  I tried to build Linux MultiMedia studio from the source of the SourceForge git:// repository under Ubuntu 12.04 LTS 32b: git clone git://lmms.git.sourceforge.net/gitroot/lmms/lmms cd lmms git checkout First I tried to install all the required libraries and then I cmaked. - That's what happened on cmake (errors occurred!): [DIR]lmms/build$ cmake .. -- The C compiler identification is GNU -- The CXX compiler identification is GNU -- Check for working C compiler: /usr/bin/gcc -- Check for working C compiler: /usr/bin/gcc -- works -- Detecting C compiler ABI info -- Detecting C compiler ABI info - done -- Check for working CXX compiler: /usr/bin/c++ -- Check for working CXX compiler: /usr/bin/c++ -- works -- Detecting CXX compiler ABI info -- Detecting CXX compiler ABI info - done PROCESSOR: i686 Machine: i686-linux-gnu -- Target host is 32 bit -- Looking for include files LMMS_HAVE_STDINT_H -- Looking for include files LMMS_HAVE_STDINT_H - found -- Looking for include files LMMS_HAVE_STDBOOL_H -- Looking for include files LMMS_HAVE_STDBOOL_H - found -- Looking for include files LMMS_HAVE_STDLIB_H -- Looking for include files LMMS_HAVE_STDLIB_H - found -- Looking for include files LMMS_HAVE_PTHREAD_H -- Looking for include files LMMS_HAVE_PTHREAD_H - found -- Looking for include files LMMS_HAVE_SEMAPHORE_H -- Looking for include files LMMS_HAVE_SEMAPHORE_H - found -- Looking for include files LMMS_HAVE_UNISTD_H -- Looking for include files LMMS_HAVE_UNISTD_H - found -- Looking for include files LMMS_HAVE_SYS_TYPES_H -- Looking for include files LMMS_HAVE_SYS_TYPES_H - found -- Looking for include files LMMS_HAVE_SYS_IPC_H -- Looking for include files LMMS_HAVE_SYS_IPC_H - found -- Looking for include files LMMS_HAVE_SYS_SHM_H -- Looking for include files LMMS_HAVE_SYS_SHM_H - found -- Looking for include files LMMS_HAVE_SYS_TIME_H -- Looking for include files LMMS_HAVE_SYS_TIME_H - found -- Looking for include files LMMS_HAVE_SYS_WAIT_H -- Looking for include files LMMS_HAVE_SYS_WAIT_H - found -- Looking for include files LMMS_HAVE_SYS_SELECT_H -- Looking for include files LMMS_HAVE_SYS_SELECT_H - found -- Looking for include files LMMS_HAVE_STDARG_H -- Looking for include files LMMS_HAVE_STDARG_H - found -- Looking for include files LMMS_HAVE_SIGNAL_H -- Looking for include files LMMS_HAVE_SIGNAL_H - found -- Looking for include files LMMS_HAVE_SCHED_H -- Looking for include files LMMS_HAVE_SCHED_H - found -- Looking for include files LMMS_HAVE_SYS_SOUNDCARD_H -- Looking for include files LMMS_HAVE_SYS_SOUNDCARD_H - found -- Looking for include files LMMS_HAVE_SOUNDCARD_H -- Looking for include files LMMS_HAVE_SOUNDCARD_H - not found. -- Looking for include files LMMS_HAVE_FCNTL_H -- Looking for include files LMMS_HAVE_FCNTL_H - found -- Looking for include files LMMS_HAVE_SYS_IOCTL_H -- Looking for include files LMMS_HAVE_SYS_IOCTL_H - found -- Looking for include files LMMS_HAVE_CTYPE_H -- Looking for include files LMMS_HAVE_CTYPE_H - found -- Looking for include files LMMS_HAVE_STRING_H -- Looking for include files LMMS_HAVE_STRING_H - found -- Looking for include files LMMS_HAVE_PROCESS_H -- Looking for include files LMMS_HAVE_PROCESS_H - not found. -- Looking for include files LMMS_HAVE_LOCALE_H -- Looking for include files LMMS_HAVE_LOCALE_H - found -- Looking for Q_WS_X11 -- Looking for Q_WS_X11 - found -- Looking for Q_WS_WIN -- Looking for Q_WS_WIN - not found. -- Looking for Q_WS_QWS -- Looking for Q_WS_QWS - not found. -- Looking for Q_WS_MAC -- Looking for Q_WS_MAC - not found. -- Found Qt4: /usr/bin/qmake (found suitable version "4.8.1", required is "4.6.0;COMPONENTS;QtCore;QtGui;QtXml;QtNetwork") -- Found Qt translations in /usr/share/qt4/translations -- checking for module 'sndfile>=1.0.11' -- found sndfile, version 1.0.25 -- Looking for include files CMAKE_HAVE_PTHREAD_H -- Looking for include files CMAKE_HAVE_PTHREAD_H - found -- Looking for pthread_create in pthreads -- Looking for pthread_create in pthreads - not found -- Looking for pthread_create in pthread -- Looking for pthread_create in pthread - found -- Found Threads: TRUE -- Found libzip: /usr/lib/libzip.so -- Found libflac++: /usr/lib/i386-linux-gnu/libFLAC.so;/usr/lib/i386-linux-gnu/libFLAC++.so -- Found STK: /usr/lib/i386-linux-gnu/libstk.so -- checking for module 'portaudio-2.0' -- found portaudio-2.0, version 19 -- Found Portaudio: portaudio;asound;m;pthread -- checking for module 'libpulse' -- found libpulse, version 1.1 -- Found PulseAudio Simple: /usr/lib/i386-linux-gnu/libpulse.so -- Looking for vorbis_bitrate_addblock in vorbis -- Looking for vorbis_bitrate_addblock in vorbis - found -- Found OggVorbis: /usr/lib/i386-linux-gnu/libogg.so;/usr/lib/i386-linux-gnu/libvorbis.so;/usr/lib/i386-linux-gnu/libvorbisfile.so;/usr/lib/i386-linux-gnu/libvorbisenc.so -- Looking for snd_seq_create_simple_port in asound -- Looking for snd_seq_create_simple_port in asound - found -- Found ALSA: /usr/lib/i386-linux-gnu/libasound.so -- Looking for include files LMMS_HAVE_MACHINE_SOUNDCARD_H -- Looking for include files LMMS_HAVE_MACHINE_SOUNDCARD_H - not found. -- Looking for include files LMMS_HAVE_LINUX_AWE_VOICE_H -- Looking for include files LMMS_HAVE_LINUX_AWE_VOICE_H - not found. -- Looking for include files LMMS_HAVE_AWE_VOICE_H -- Looking for include files LMMS_HAVE_AWE_VOICE_H - not found. -- Looking for include files LMMS_HAVE__USR_SRC_SYS_I386_ISA_SOUND_AWE_VOICE_H -- Looking for include files LMMS_HAVE__USR_SRC_SYS_I386_ISA_SOUND_AWE_VOICE_H - not found. -- Looking for include files LMMS_HAVE__USR_SRC_SYS_GNU_I386_ISA_SOUND_AWE_VOICE_H -- Looking for include files LMMS_HAVE__USR_SRC_SYS_GNU_I386_ISA_SOUND_AWE_VOICE_H - not found. -- Looking for C++ include sys/asoundlib.h -- Looking for C++ include sys/asoundlib.h - found -- Looking for C++ include alsa/asoundlib.h -- Looking for C++ include alsa/asoundlib.h - found -- Looking for snd_pcm_resume in asound -- Looking for snd_pcm_resume in asound - found -- checking for module 'jack>=0.77' -- found jack, version 0.121.2 -- checking for module 'fftw3f>=3.0.0' -- package 'fftw3f>=3.0.0' not found CMake Error at /usr/share/cmake-2.8/Modules/FindPkgConfig.cmake:266 (message): A required package was not found Call Stack (most recent call first): /usr/share/cmake-2.8/Modules/FindPkgConfig.cmake:320 (_pkg_check_modules_internal) CMakeLists.txt:309 (PKG_CHECK_MODULES) -- checking for module 'fluidsynth>=1.0.7' -- found fluidsynth, version 1.1.5 -- Looking for include files LMMS_HAVE_LV2CORE -- Looking for include files LMMS_HAVE_LV2CORE - found -- Looking for include files LMMS_HAVE_SLV2_SCALEPOINTS_H -- Looking for include files LMMS_HAVE_SLV2_SCALEPOINTS_H - not found. -- Looking for slv2_world_new in slv2 -- Looking for slv2_world_new in slv2 - found -- Looking for librdf_new_world in rdf -- Looking for librdf_new_world in rdf - found -- Looking for wine_init in wine -- Looking for wine_init in wine - found -- Looking for C++ include windows.h -- Looking for C++ include windows.h - found -- checking for module 'samplerate>=0.1.7' -- package 'samplerate>=0.1.7' not found -- Performing Test HAVE_LRINT -- Performing Test HAVE_LRINT - Success -- Performing Test HAVE_LRINTF -- Performing Test HAVE_LRINTF - Success -- Performing Test CPU_CLIPS_POSITIVE -- Performing Test CPU_CLIPS_POSITIVE - Failed -- Performing Test CPU_CLIPS_NEGATIVE -- Performing Test CPU_CLIPS_NEGATIVE - Success -- Looking for XOpenDisplay in /usr/lib/i386-linux-gnu/libX11.so;/usr/lib/i386-linux-gnu/libXext.so -- Looking for XOpenDisplay in /usr/lib/i386-linux-gnu/libX11.so;/usr/lib/i386-linux-gnu/libXext.so - found -- Looking for gethostbyname -- Looking for gethostbyname - found -- Looking for connect -- Looking for connect - found -- Looking for remove -- Looking for remove - found -- Looking for shmat -- Looking for shmat - found -- Looking for IceConnectionNumber in ICE -- Looking for IceConnectionNumber in ICE - found -- Found X11: /usr/lib/i386-linux-gnu/libX11.so -- Found Freetype: /usr/lib/i386-linux-gnu/libfreetype.so Installation Summary -------------------- * Install Directory : /usr/local * Use system's libsamplerate : Supported audio interfaces -------------------------- * ALSA : OK * JACK : OK * OSS : OK * PortAudio : OK * PulseAudio : OK * SDL : OK Supported MIDI interfaces ------------------------- * ALSA : OK * OSS : OK * WinMM : <not supported on this platform> Supported file formats for project export ----------------------------------------- * WAVE : OK * OGG/VORBIS : OK * FLAC : OK Optional plugins ---------------- * SoundFont2 player : OK * Stk Mallets : OK * VST-instrument hoster : OK * VST-effect hoster : OK * LV2 hoster : OK * CALF LADSPA plugins : OK * CAPS LADSPA plugins : OK * CMT LADSPA plugins : OK * TAP LADSPA plugins : OK * SWH LADSPA plugins : OK * FL .zip import : OK ----------------------------------------------------------------- IMPORTANT: after installing missing packages, remove CMakeCache.txt before running cmake again! ----------------------------------------------------------------- -- Configuring incomplete, errors occurred! Here are some parts the contents of my lmms/build/CMakeCache.txt file: # This is the CMakeCache file. # For build in directory: /home/jk/Downloads/lmms-git/lmms/build # It was generated by CMake: /usr/bin/cmake # You can edit this file to change values found and used by cmake. # If you do not want to change any of the values, simply exit the editor. # If you do want to change a value, simply edit, save, and exit the editor. # The syntax for the file is as follows: # KEY:TYPE=VALUE # KEY is the name of a variable in the cache. # TYPE is a hint to GUI's for the type of VALUE, DO NOT EDIT TYPE!. # VALUE is the current value for the KEY. ######################## # EXTERNAL cache entries ######################## //Path to a file. ALSA_INCLUDES:PATH=/usr/include //Path to a library. ASOUND_LIBRARY:FILEPATH=/usr/lib/i386-linux-gnu/libasound.so //Path to a program. CMAKE_AR:FILEPATH=/usr/bin/ar //Choose the type of build, options are: None(CMAKE_CXX_FLAGS or // CMAKE_C_FLAGS used) Debug Release RelWithDebInfo MinSizeRel. CMAKE_BUILD_TYPE:STRING= //Enable/Disable color output during build. CMAKE_COLOR_MAKEFILE:BOOL=ON //CXX compiler. CMAKE_CXX_COMPILER:FILEPATH=/usr/bin/c++ //Flags used by the compiler during all build types. CMAKE_CXX_FLAGS:STRING= //Flags used by the compiler during debug builds. CMAKE_CXX_FLAGS_DEBUG:STRING=-g //Flags used by the compiler during release minsize builds. CMAKE_CXX_FLAGS_MINSIZEREL:STRING=-Os -DNDEBUG //Flags used by the compiler during release builds (/MD /Ob1 /Oi // /Ot /Oy /Gs will produce slightly less optimized but smaller // files). CMAKE_CXX_FLAGS_RELEASE:STRING=-O3 -DNDEBUG //Flags used by the compiler during Release with Debug Info builds. CMAKE_CXX_FLAGS_RELWITHDEBINFO:STRING=-O2 -g //C compiler. CMAKE_C_COMPILER:FILEPATH=/usr/bin/gcc //Flags used by the compiler during all build types. CMAKE_C_FLAGS:STRING= //Flags used by the compiler during debug builds. CMAKE_C_FLAGS_DEBUG:STRING=-g //Flags used by the compiler during release minsize builds. CMAKE_C_FLAGS_MINSIZEREL:STRING=-Os -DNDEBUG //Flags used by the compiler during release builds (/MD /Ob1 /Oi // /Ot /Oy /Gs will produce slightly less optimized but smaller // files). CMAKE_C_FLAGS_RELEASE:STRING=-O3 -DNDEBUG //Flags used by the compiler during Release with Debug Info builds. CMAKE_C_FLAGS_RELWITHDEBINFO:STRING=-O2 -g //Flags used by the linker. CMAKE_EXE_LINKER_FLAGS:STRING=' ' //Flags used by the linker during debug builds. CMAKE_EXE_LINKER_FLAGS_DEBUG:STRING= //Flags used by the linker during release minsize builds. CMAKE_EXE_LINKER_FLAGS_MINSIZEREL:STRING= //Flags used by the linker during release builds. CMAKE_EXE_LINKER_FLAGS_RELEASE:STRING= //Flags used by the linker during Release with Debug Info builds. CMAKE_EXE_LINKER_FLAGS_RELWITHDEBINFO:STRING= //Enable/Disable output of compile commands during generation. CMAKE_EXPORT_COMPILE_COMMANDS:BOOL=OFF //Install path prefix, prepended onto install directories. CMAKE_INSTALL_PREFIX:PATH=/usr/local //Path to a program. CMAKE_LINKER:FILEPATH=/usr/bin/ld //Path to a program. CMAKE_MAKE_PROGRAM:FILEPATH=/usr/bin/make //Flags used by the linker during the creation of modules. CMAKE_MODULE_LINKER_FLAGS:STRING=' ' //Flags used by the linker during debug builds. CMAKE_MODULE_LINKER_FLAGS_DEBUG:STRING= //Flags used by the linker during release minsize builds. CMAKE_MODULE_LINKER_FLAGS_MINSIZEREL:STRING= //Flags used by the linker during release builds. CMAKE_MODULE_LINKER_FLAGS_RELEASE:STRING= //Flags used by the linker during Release with Debug Info builds. CMAKE_MODULE_LINKER_FLAGS_RELWITHDEBINFO:STRING= ==[...]== That's a list of the contents of my lmms/build folder: [DIR]lmms/build$ dir CMakeCache.txt CPackSourceConfig.cmake lmmsconfig.h plugins CMakeFiles data lmms.rc CPackConfig.cmake include lmmsversion.h My Question: It just tells me that that "errors" occurred, but I can't see any error message. It seems like everything went fine. - So: Any idea what the problem could be? - Thanks.

  Read the article

• Compiling ruby1.9.1 hangs and fills swap!

  - by nfm

  I'm compiling Ruby 1.9.1-p376 under Ubuntu 8.04 server LTS (64-bit), by doing the following: $ ./configure $ make $ sudo make install ./configure works without complaints. make hangs indefinitely until all my RAM and swap is gone. It get stuck after the following output: compiling ripper make[1]: Entering directory `/tmp/ruby1.9.1/ruby-1.9.1-p376/ext/ripper' gcc -I. -I../../.ext/include/x86_64-linux -I../.././include -I../.././ext/ripper -I../.. -I../../. -DRUBY_EXTCONF_H=\"extconf.h\" -fPIC -O2 -g -Wall -Wno-parentheses -o ripper.o -c ripper.c If I run the gcc command by hand, with the -v argument to get verbose output, it hangs after the following: Using built-in specs. Target: x86_64-linux-gnu Configured with: ../src/configure -v --enable-languages=c,c++,fortran,objc,obj-c++,treelang --prefix=/usr --enable-shared --with-system-zlib --libexecdir=/usr/lib --without-included-gettext --enable-threads=posix --enable-nls --with-gxx-include-dir=/usr/include/c++/4.2 --program-suffix=-4.2 --enable-clocale=gnu --enable-libstdcxx-debug --enable-objc-gc --enable-mpfr --enable-checking=release --build=x86_64-linux-gnu --host=x86_64-linux-gnu --target=x86_64-linux-gnu Thread model: posix gcc version 4.2.4 (Ubuntu 4.2.4-1ubuntu4) /usr/lib/gcc/x86_64-linux-gnu/4.2.4/cc1 -quiet -v -I. -I../../.ext/include/x86_64-linux -I../.././include -I../.././ext/ripper -I../.. -I../../. -DRUBY_EXTCONF_H="extconf.h" ripper.c -quiet -dumpbase ripper.c -mtune=generic -auxbase-strip ripper.o -g -O2 -Wall -Wno-parentheses -version -fPIC -fstack-protector -fstack-protector -o /tmp/ccRzHvYH.s ignoring nonexistent directory "/usr/local/include/x86_64-linux-gnu" ignoring nonexistent directory "/usr/lib/gcc/x86_64-linux-gnu/4.2.4/../../../../x86_64-linux-gnu/include" ignoring nonexistent directory "/usr/include/x86_64-linux-gnu" ignoring duplicate directory "../.././ext/ripper" ignoring duplicate directory "../../." #include "..." search starts here: #include <...> search starts here: . ../../.ext/include/x86_64-linux ../.././include ../.. /usr/local/include /usr/lib/gcc/x86_64-linux-gnu/4.2.4/include /usr/include End of search list. GNU C version 4.2.4 (Ubuntu 4.2.4-1ubuntu4) (x86_64-linux-gnu) compiled by GNU C version 4.2.4 (Ubuntu 4.2.4-1ubuntu4). GGC heuristics: --param ggc-min-expand=47 --param ggc-min-heapsize=32795 Compiler executable checksum: 6e11fa7ca85fc28646173a91f2be2ea3 I just compiled ruby on another computer for reference, and it took about 10 seconds to print the following output (after the above Compiler executable checksum line): COLLECT_GCC_OPTIONS='-v' '-I.' '-I../../.ext/include/i686-linux' '-I../.././include' '-I../.././ext/ripper' '-I../..' '-I../../.' '-DRUBY_EXTCONF_H="extconf.h"' '-D_FILE_OFFSET_BITS=64' '-fPIC' '-O2' '-g' '-Wall' '-Wno-parentheses' '-o' 'ripper.o' '-c' '-mtune=generic' '-march=i486' as -V -Qy -o ripper.o /tmp/cca4fa7R.s GNU assembler version 2.20 (i486-linux-gnu) using BFD version (GNU Binutils for Ubuntu) 2.20 COMPILER_PATH=/usr/lib/gcc/i486-linux-gnu/4.4.1/:/usr/lib/gcc/i486-linux-gnu/4.4.1/:/usr/lib/gcc/i486-linux-gnu/:/usr/lib/gcc/i486-linux-gnu/4.4.1/:/usr/lib/gcc/i486-linux-gnu/:/usr/lib/gcc/i486-linux-gnu/4.4.1/:/usr/lib/gcc/i486-linux-gnu/ LIBRARY_PATH=/usr/lib/gcc/i486-linux-gnu/4.4.1/:/usr/lib/gcc/i486-linux-gnu/4.4.1/:/usr/lib/gcc/i486-linux-gnu/4.4.1/../../../../lib/:/lib/../lib/:/usr/lib/../lib/:/usr/lib/gcc/i486-linux-gnu/4.4.1/../../../:/lib/:/usr/lib/ COLLECT_GCC_OPTIONS='-v' '-I.' '-I../../.ext/include/i686-linux' '-I../.././include' '-I../.././ext/ripper' '-I../..' '-I../../.' '-DRUBY_EXTCONF_H="extconf.h"' '-D_FILE_OFFSET_BITS=64' '-fPIC' '-O2' '-g' '-Wall' '-Wno-parentheses' '-o' 'ripper.o' '-c' '-mtune=generic' '-march=i486' I have absolutely no clue what could be going wrong here - any ideas where I should start?

  Read the article

• How do I get a rt2800usb wireless device working?

  - by Jii

  My brand new desktop running 13.04 has endless problems with wireless. Dozens of others are flooding forums with reports of the same problems. It worked fine for a few days, then there were a few days where it started having problems sometimes and working sometimes. Now it never works at all. I have 5+ devices all able to connect without any trouble at all, including iPhone, Android phone, 3DS, multiple game consoles, a laptop running windows 7, and even a second desktop machine running Ubuntu 12.04 sitting right behind the 13.04 machine. All other devices have full wireless bars displayed (strong signals). At any moment, one of the following is happening, and it changes randomly: Trying to connect forever, but never establishing a connection. Wireless icon constantly animating. Finds no wireless networks at all. (There are 12+ in range according to other devices.) Will not try to connect to the network. If I use the icon to connect, it will display "Disconnected" within a few seconds. Will continuously ask for the network password. Typing it in correctly does not help. Wireless is working fine. This happens sometimes. It can work for days at a time, or only 10 mins at a time. Various things that usually do nothing but sometimes fix the problem: Reboot. This has the best chance of helping, but it usually takes 5+ times. Disable/re-enable Wi-Fi using the wireless icon. Disable/re-enable Networking using the wireless icon. Use the icon to try and connect to a network (if found). Use the icon to open Edit Connections and delete my connection info, causing it to be recreated (once it's actually found again). Various things that seem to make no difference: Changing between using Linux headers in grub at bootup, between 3.10.0, 3.9.0, or 3.8.0. Move the wireless router very close to the desktop. Running sudo rfkill unblock all (I dunno what this is supposed to do.) I've used Ubuntu for 6 years and I've never had a problem with networking. Now I'm spending all my time reading through endless problem reports and trying all the answers. None of them have helped. I am doing this instead of getting work done, which is defeating the whole purpose of using Ubuntu. It's heartbreaking to be honest. In the current state of "no networks are showing up", here are outputs from the random things that other people are usually asked to run: lspic 00:00.0 Host bridge: Intel Corporation Haswell DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Haswell PCI Express x16 Controller (rev 06) 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Lynx Point MEI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 04) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Lynx Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Lynx Point PCI Express Root Port #1 (rev d4) 00:1c.2 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d4) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Lynx Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-port SATA Controller 1 [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Lynx Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 610] (rev a1) 01:00.1 Audio device: NVIDIA Corporation GF119 HDMI Audio Controller (rev a1) 03:00.0 PCI bridge: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge (rev 03) lsmod Module Size Used by e100 41119 0 nls_iso8859_1 12713 1 parport_pc 28284 0 ppdev 17106 0 bnep 18258 2 rfcomm 47863 12 binfmt_misc 17540 1 arc4 12573 2 rt2800usb 27201 0 rt2x00usb 20857 1 rt2800usb rt2800lib 68029 1 rt2800usb rt2x00lib 55764 3 rt2x00usb,rt2800lib,rt2800usb coretemp 13596 0 mac80211 656164 3 rt2x00lib,rt2x00usb,rt2800lib kvm_intel 138733 0 kvm 452835 1 kvm_intel cfg80211 547224 2 mac80211,rt2x00lib crc_ccitt 12707 1 rt2800lib ghash_clmulni_intel 13259 0 aesni_intel 55449 0 usb_storage 61749 1 aes_x86_64 17131 1 aesni_intel joydev 17613 0 xts 12922 1 aesni_intel nouveau 1001310 3 snd_hda_codec_hdmi 37407 1 lrw 13294 1 aesni_intel gf128mul 14951 2 lrw,xts mxm_wmi 13021 1 nouveau snd_hda_codec_realtek 46511 1 ablk_helper 13597 1 aesni_intel wmi 19256 2 mxm_wmi,nouveau snd_hda_intel 44397 5 ttm 88251 1 nouveau drm_kms_helper 49082 1 nouveau drm 295908 5 ttm,drm_kms_helper,nouveau snd_hda_codec 190010 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel cryptd 20501 3 ghash_clmulni_intel,aesni_intel,ablk_helper snd_hwdep 13613 1 snd_hda_codec snd_pcm 102477 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel btusb 18291 0 snd_page_alloc 18798 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 i2c_algo_bit 13564 1 nouveau snd_seq_midi_event 14899 1 snd_seq_midi snd_rawmidi 30417 1 snd_seq_midi snd_seq 61930 2 snd_seq_midi_event,snd_seq_midi bluetooth 251354 22 bnep,btusb,rfcomm snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi lpc_ich 17060 0 snd_timer 29989 2 snd_pcm,snd_seq mei 46588 0 snd 69533 20 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device psmouse 97838 0 microcode 22923 0 soundcore 12680 1 snd video 19467 1 nouveau mac_hid 13253 0 serio_raw 13215 0 lp 17799 0 parport 46562 3 lp,ppdev,parport_pc hid_generic 12548 0 usbhid 47346 0 hid 101248 2 hid_generic,usbhid ahci 30063 3 libahci 32088 1 ahci e1000e 207005 0 ptp 18668 1 e1000e pps_core 14080 1 ptp sudo lshw -c network 00:00.0 Host bridge: Intel Corporation Haswell DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Haswell PCI Express x16 Controller (rev 06) 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Lynx Point MEI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 04) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Lynx Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Lynx Point PCI Express Root Port #1 (rev d4) 00:1c.2 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d4) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Lynx Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-port SATA Controller 1 [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Lynx Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 610] (rev a1) 01:00.1 Audio device: NVIDIA Corporation GF119 HDMI Audio Controller (rev a1) 03:00.0 PCI bridge: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge (rev 03) sudo iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on sudo iwlist scan eth0 Interface doesn't support scanning. lo Interface doesn't support scanning. wlan0 No scan results NOTE: This dmesg was done after a reboot where the network manager was continuously displaying the "disconnected" message over and over. So it must have been trying to connect at this time. My network was displayed in the list of options, as the only option despite other devices picking up 12+ access points. The router channel is set to auto. dmesg | tail -30 [ 187.418446] wlan0: associated [ 190.405601] wlan0: disassociated from 00:14:d1:a8:c3:44 (Reason: 15) [ 190.443312] cfg80211: Calling CRDA to update world regulatory domain [ 190.443431] wlan0: deauthenticating from 00:14:d1:a8:c3:44 by local choice (reason=3) [ 190.451635] cfg80211: World regulatory domain updated: [ 190.451643] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 190.451648] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 190.451652] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 190.451656] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 190.451659] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 190.451662] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 191.824451] wlan0: authenticate with 00:14:d1:a8:c3:44 [ 191.850608] wlan0: send auth to 00:14:d1:a8:c3:44 (try 1/3) [ 191.884604] wlan0: send auth to 00:14:d1:a8:c3:44 (try 2/3) [ 191.886309] wlan0: authenticated [ 191.886579] rt2800usb 3-5.3:1.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 191.886588] rt2800usb 3-5.3:1.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 191.889556] wlan0: associate with 00:14:d1:a8:c3:44 (try 1/3) [ 192.001493] wlan0: associate with 00:14:d1:a8:c3:44 (try 2/3) [ 192.040274] wlan0: RX AssocResp from 00:14:d1:a8:c3:44 (capab=0x431 status=0 aid=3) [ 192.044235] wlan0: associated [ 193.948188] wlan0: deauthenticating from 00:14:d1:a8:c3:44 by local choice (reason=3) [ 193.981501] cfg80211: Calling CRDA to update world regulatory domain [ 193.984080] cfg80211: World regulatory domain updated: [ 193.984082] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 193.984084] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 193.984085] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 193.984085] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 193.984086] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 193.984087] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) The router uses MAC filtering, and security is WPA PSK with cipher as auto. So, any ideas? Or is the solution just to not use 13.04 unless you have a wired connection? (I don't have this option.) If so, please just tell me straight. I survived 9.04 Jaunty, and I can survive 13.04 Raring. Update #1 Results from trying Wild Man's first answer: jii@conan:~$ echo "options rt2800usb nohwcrypt=y" | sudo tee /etc/modprobe.d/rt2800usb.conf options rt2800usb nohwcrypt=y jii@conan:~$ sudo modprobe -rfv rt2800usb rmmod rt2800usb rmmod rt2800lib rmmod crc_ccitt rmmod rt2x00usb rmmod rt2x00lib rmmod mac80211 rmmod cfg80211 jii@conan:~$ sudo modprobe -v rt2800usb insmod /lib/modules/3.10.0-031000-generic/kernel/lib/crc-ccitt.ko insmod /lib/modules/3.10.0-031000-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.10.0-031000-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2x00lib.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2800lib.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2x00usb.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2800usb.ko nohwcrypt=y I tried: gksudo gedit /etc/pm/power.d/wireless but I didn't have the package. It said to install gksu. I tried that, but of course, not having Internet, I didn't get the package. So instead I did: sudo gedit /etc/pm/power.d/wireless Which created the file. Here is the body: #!/bin/sh /sbin/iwconfig wlan0 power off I then rebooted. No change. I tried adding exit 0 to the bottom of the wireless file, and rebooted. No change. Please note that this is a desktop machine. I'm assuming power management is primarily for laptops, but the iwconfig does state that power management is on, so who knows. The recommended router changes I did not do, since the current router settings are (I think) required for some of the older devices I have, and because the current settings work on all my modern devices including Ubuntu 12.04 and Windows 7. I do appreciate the advice though, and I'll look into it when I have time. Anything else to try? Update #2 I booted into Ubuntu 12.04.3 from a dvd, and the same problems exist. I have a separate old desktop machine with 12.04 installed that has no wireless problems at all. So obviously the problem is wireless hardware compatibility in both 12.04.03 LTS and 13.04. Update #3 The same problems exist even when using a wired connection. I plugged an ethernet cable directly to the router and the network manager added an "Auto Ethernet" entry, but it cannot establish a connection to it. So the problem is not specific to wireless. Meanwhile, I purchased a Trendnet N300 wireless USB adapter, TEW-664UB. I plugged it in, but I have no idea how to get Ubuntu to try and use it. Can anyone tell me how? Can I download a package on another computer and copy the .deb over to do an install, etc? I'm installing windows 7 to double check that the internet connection works there and it's not just some magically faulty hardware. Thanks for your help.

  Read the article

• Cannot ping router with a static IP assigned?

  - by Uriah

  Alright. I am running Ubuntu LTS 12.04 and am trying to configure a local caching/master DNS server so I am using Bind9. First, here are some things via default DHCP: /etc/network/interfaces cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # The primary network interface - STATIC #auto eth0 #iface eth0 inet static # address 192.168.2.113 # netmask 255.255.255.0 # network 192.168.2.0 # broadcast 192.168.2.255 # gateway 192.168.2.1 # dns-search uclemmer.net # dns-nameservers 192.168.2.113 8.8.8.8 /etc/resolv.conf cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 192.168.2.1 search uclemmer.net ifconfig ifconfig eth0 Link encap:Ethernet HWaddr 00:14:2a:82:d4:9e inet addr:192.168.2.103 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::214:2aff:fe82:d49e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1067 errors:0 dropped:0 overruns:0 frame:0 TX packets:2504 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:153833 (153.8 KB) TX bytes:214129 (214.1 KB) Interrupt:23 Base address:0x8800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:915 errors:0 dropped:0 overruns:0 frame:0 TX packets:915 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:71643 (71.6 KB) TX bytes:71643 (71.6 KB) ping ping -c 4 192.168.2.1 PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data. 64 bytes from 192.168.2.1: icmp_req=1 ttl=64 time=0.368 ms 64 bytes from 192.168.2.1: icmp_req=2 ttl=64 time=0.224 ms 64 bytes from 192.168.2.1: icmp_req=3 ttl=64 time=0.216 ms 64 bytes from 192.168.2.1: icmp_req=4 ttl=64 time=0.237 ms --- 192.168.2.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2997ms rtt min/avg/max/mdev = 0.216/0.261/0.368/0.063 ms ping -c 4 google.com PING google.com (74.125.134.102) 56(84) bytes of data. 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=1 ttl=48 time=15.1 ms 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=2 ttl=48 time=11.4 ms 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=3 ttl=48 time=11.6 ms 64 bytes from www.google-analytics.com (74.125.134.102): icmp_req=4 ttl=48 time=11.5 ms --- google.com ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3003ms rtt min/avg/max/mdev = 11.488/12.465/15.118/1.537 ms ip route ip route default via 192.168.2.1 dev eth0 metric 100 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.103 As you can see, with DHCP everything seems to work fine. Now, here are things with static IP: /etc/network/interfaces cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface #auto eth0 #iface eth0 inet dhcp # The primary network interface - STATIC auto eth0 iface eth0 inet static address 192.168.2.113 netmask 255.255.255.0 network 192.168.2.0 broadcast 192.168.2.255 gateway 192.168.2.1 dns-search uclemmer.net dns-nameservers 192.168.2.1 8.8.8.8 I have tried dns-nameservers in various combos of *.2.1, *.2.113, and other reliable, public nameservers. /etc/resolv.conf cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 192.168.2.1 nameserver 8.8.8.8 search uclemmer.net Obviously, when I change the nameservers in the /etc/network/interfaces file, the nameservers change here too. ifconfig ifconfig eth0 Link encap:Ethernet HWaddr 00:14:2a:82:d4:9e inet addr:192.168.2.113 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::214:2aff:fe82:d49e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1707 errors:0 dropped:0 overruns:0 frame:0 TX packets:2906 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:226230 (226.2 KB) TX bytes:263497 (263.4 KB) Interrupt:23 Base address:0x8800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:985 errors:0 dropped:0 overruns:0 frame:0 TX packets:985 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:78625 (78.6 KB) TX bytes:78625 (78.6 KB) ping ping -c 4 192.168.2.1 PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data. --- 192.168.2.1 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3023ms ping -c 4 google.com ping: unknown host google.com Lastly, here are my bind zone files: /etc/bind/named.conf.options cat /etc/bind/named.conf.options options { directory "/etc/bind"; // // // query-source address * port 53; notify-source * port 53; transfer-source * port 53; // If there is a firewall between you and nameservers you want // to talk to, you may need to fix the firewall to allow multiple // ports to talk. See http://www.kb.cert.org/vuls/id/800113 // If your ISP provided one or more IP addresses for stable // nameservers, you probably want to use them as forwarders. // Uncomment the following block, and insert the addresses replacing // the all-0's placeholder. // forwarders { // 0.0.0.0; // }; forwarders { // My local 192.168.2.113; // Comcast 75.75.75.75; 75.75.76.76; // Google 8.8.8.8; 8.8.4.4; // DNSAdvantage 156.154.70.1; 156.154.71.1; // OpenDNS 208.67.222.222; 208.67.220.220; // Norton 198.153.192.1; 198.153.194.1; // Verizon 4.2.2.1; 4.2.2.2; 4.2.2.3; 4.2.2.4; 4.2.2.5; 4.2.2.6; // Scrubit 67.138.54.100; 207.255.209.66; }; // // // //allow-query { localhost; 192.168.2.0/24; }; //allow-transfer { localhost; 192.168.2.113; }; //also-notify { 192.168.2.113; }; //allow-recursion { localhost; 192.168.2.0/24; }; //======================================================================== // If BIND logs error messages about the root key being expired, // you will need to update your keys. See https://www.isc.org/bind-keys //======================================================================== dnssec-validation auto; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; /etc/bind/named.conf.local cat /etc/bind/named.conf.local // // Do any local configuration here // // Consider adding the 1918 zones here, if they are not used in your // organization //include "/etc/bind/zones.rfc1918"; zone "example.com" { type master; file "/etc/bind/zones/db.example.com"; }; zone "2.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/db.2.168.192.in-addr.arpa"; /etc/bind/zones/db.example.com cat /etc/bind/zones/db.example.com ; ; BIND data file for example.com interface ; $TTL 604800 @ IN SOA yossarian.example.com. root.example.com. ( 1343171970 ; Serial 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; @ IN NS yossarian.example.com. @ IN A 192.168.2.113 @ IN AAAA ::1 @ IN MX 10 yossarian.example.com. ; yossarian IN A 192.168.2.113 router IN A 192.168.2.1 printer IN A 192.168.2.200 ; ns01 IN CNAME yossarian.example.com. www IN CNAME yossarian.example.com. ftp IN CNAME yossarian.example.com. ldap IN CNAME yossarian.example.com. mail IN CNAME yossarian.example.com. /etc/bind/zones/db.2.168.192.in-addr.arpa cat /etc/bind/zones/db.2.168.192.in-addr.arpa ; ; BIND reverse data file for 2.168.192.in-addr interface ; $TTL 604800 @ IN SOA yossarian.example.com. root.example.com. ( 1343171970 ; Serial 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; @ IN NS yossarian.example.com. @ IN A 255.255.255.0 ; 113 IN PTR yossarian.example.com. 1 IN PTR router.example.com. 200 IN PTR printer.example.com. ip route ip route default via 192.168.2.1 dev eth0 metric 100 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.113 I can SSH in to the machine locally at *.2.113 or at whatever address is dynamically assigned when in DHCP "mode". *2.113 is in my router's range and I have ports open and forwarding to the server. Pinging is enabled on the router too. I briefly had a static configuration working but it died after the first reboot. Please let me know what other info you might need. I am beyond frustrated/baffled.

  Read the article

• Package libxul not fount - Kiwix Wikpedia in Ubuntu Precise 12.04

  - by JHOSmAN

  I'm trying to install the service Kiwix but I need a library that is not available for Ubuntu 12.04 LTS Precise leave the log and if someone could tell me how to install Seller would appreciate. kiwix-0.9# ls aclocal.m4 COMPILE config.sub COPYING install-sh ltmain.sh missing static AUTHORS config.guess configure depcomp kiwix Makefile.am README CHANGELOG config.log configure.ac desktop libxul-dev_1.8.1.16+nobinonly-0ubuntu1_all.deb Makefile.in src root@ubuntu-MM061:/home/ubuntu/Escritorio/kiwix-0.9# ./configure checking for a BSD-compatible install... /usr/bin/install -c checking whether build environment is sane... yes checking for a thread-safe mkdir -p... /bin/mkdir -p checking for gawk... no checking for mawk... mawk checking whether make sets $(MAKE)... yes checking whether to enable maintainer-specific portions of Makefiles... no checking for gcc... gcc checking whether the C compiler works... yes checking for C compiler default output file name... a.out checking for suffix of executables... checking whether we are cross compiling... no checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether gcc accepts -g... yes checking for gcc option to accept ISO C89... none needed checking for style of include used by make... GNU checking dependency style of gcc... gcc3 checking for g++... g++ checking whether we are using the GNU C++ compiler... yes checking whether g++ accepts -g... yes checking dependency style of g++... gcc3 checking for g++... g++ checking for cl... no checking for cl... no checking for Xcode... no checking for jar... jar checking build system type... i686-pc-linux-gnu checking host system type... i686-pc-linux-gnu checking for a sed that does not truncate output... /bin/sed checking for grep that handles long lines and -e... /bin/grep checking for egrep... /bin/grep -E checking for fgrep... /bin/grep -F checking for ld used by gcc... /usr/bin/ld checking if the linker (/usr/bin/ld) is GNU ld... yes checking for BSD- or MS-compatible name lister (nm)... /usr/bin/nm -B checking the name lister (/usr/bin/nm -B) interface... BSD nm checking whether ln -s works... yes checking the maximum length of command line arguments... 1572864 checking whether the shell understands some XSI constructs... yes checking whether the shell understands "+="... yes checking for /usr/bin/ld option to reload object files... -r checking for objdump... objdump checking how to recognize dependent libraries... pass_all checking for ar... ar checking for strip... strip checking for ranlib... ranlib checking command to parse /usr/bin/nm -B output from gcc object... ok checking how to run the C preprocessor... gcc -E checking for ANSI C header files... yes checking for sys/types.h... yes checking for sys/stat.h... yes checking for stdlib.h... yes checking for string.h... yes checking for memory.h... yes checking for strings.h... yes checking for inttypes.h... yes checking for stdint.h... yes checking for unistd.h... yes checking for dlfcn.h... yes checking whether we are using the GNU C++ compiler... (cached) yes checking whether g++ accepts -g... (cached) yes checking dependency style of g++... (cached) gcc3 checking how to run the C++ preprocessor... g++ -E checking for objdir... .libs checking if gcc supports -fno-rtti -fno-exceptions... no checking for gcc option to produce PIC... -fPIC -DPIC checking if gcc PIC flag -fPIC -DPIC works... yes checking if gcc static flag -static works... yes checking if gcc supports -c -o file.o... yes checking if gcc supports -c -o file.o... (cached) yes checking whether the gcc linker (/usr/bin/ld) supports shared libraries... yes checking whether -lc should be explicitly linked in... no checking dynamic linker characteristics... GNU/Linux ld.so checking how to hardcode library paths into programs... immediate checking whether stripping libraries is possible... yes checking if libtool supports shared libraries... yes checking whether to build shared libraries... yes checking whether to build static libraries... yes checking for ld used by g++... /usr/bin/ld checking if the linker (/usr/bin/ld) is GNU ld... yes checking whether the g++ linker (/usr/bin/ld) supports shared libraries... yes checking for g++ option to produce PIC... -fPIC -DPIC checking if g++ PIC flag -fPIC -DPIC works... yes checking if g++ static flag -static works... yes checking if g++ supports -c -o file.o... yes checking if g++ supports -c -o file.o... (cached) yes checking whether the g++ linker (/usr/bin/ld) supports shared libraries... yes checking dynamic linker characteristics... GNU/Linux ld.so checking how to hardcode library paths into programs... immediate checking for ranlib... (cached) ranlib checking whether make sets $(MAKE)... (cached) yes checking for pkg-config... pkg-config checking for perl... perl checking fcntl.h usability... yes checking fcntl.h presence... yes checking for fcntl.h... yes checking float.h usability... yes checking float.h presence... yes checking for float.h... yes checking libintl.h usability... yes checking libintl.h presence... yes checking for libintl.h... yes checking limits.h usability... yes checking limits.h presence... yes checking for limits.h... yes checking stddef.h usability... yes checking stddef.h presence... yes checking for stddef.h... yes checking for stdint.h... (cached) yes checking for stdlib.h... (cached) yes checking for string.h... (cached) yes checking for strings.h... (cached) yes checking sys/socket.h usability... yes checking sys/socket.h presence... yes checking for sys/socket.h... yes checking sys/time.h usability... yes checking sys/time.h presence... yes checking for sys/time.h... yes checking for unistd.h... (cached) yes checking wchar.h usability... yes checking wchar.h presence... yes checking for wchar.h... yes checking for stdbool.h that conforms to C99... yes checking for _Bool... no checking for inline... inline checking for int16_t... yes checking for int32_t... yes checking for int64_t... yes checking for int8_t... yes checking for off_t... yes checking for pid_t... yes checking for size_t... yes checking for uint16_t... yes checking for uint32_t... yes checking for uint64_t... yes checking for uint8_t... yes checking for ptrdiff_t... yes checking vfork.h usability... no checking vfork.h presence... no checking for vfork.h... no checking for fork... yes checking for vfork... yes checking for working fork... yes checking for working vfork... (cached) yes checking for stdlib.h... (cached) yes checking for GNU libc compatible malloc... yes checking for working strtod... yes checking for getcwd... yes checking for gettimeofday... yes checking for memmove... yes checking for memset... yes checking for pow... yes checking for regcomp... yes checking for sqrt... yes checking for strcasecmp... yes checking for strchr... yes checking for strdup... yes checking for strerror... yes checking for strtol... yes Package libxul was not found in the pkg-config search path. Perhaps you should add the directory containing libxul.pc' to the PKG_CONFIG_PATH environment variable No package 'libxul' found Package libxul was not found in the pkg-config search path. Perhaps you should add the directory containinglibxul.pc' to the PKG_CONFIG_PATH environment variable No package 'libxul' found checking for /stable... no checking for "/nsISupports.idl"... no configure: error: unable to find nsISupports.idl apt-get install libxul Leyendo lista de paquetes... Hecho Creando árbol de dependencias Leyendo la información de estado... Hecho E: No se ha podido localizar el paquete libxul

  Read the article

• 12.04 upgrade broke grub? (not wubi related)

  - by kaare

  I just updated from 11.10 to 12.04, with no major problems (it took a while to get past a request to restart ssh, mysql and some other services, but I did no fiddling by myself, everything was done by the installer). However, after restarting, grub can't do anything. Picking the new linux installation (first entry), I just get error: no such partition error: no such partition error: no such partition and picking the recovery-version just gives 5 lines instead of 3. I have windows 7 installed on a different drive, and can run it by booting from that drive instead. Picking it from the grub menu gives the same error as above (can't remember how many lines, though). I'll be honest and say that I don't remember if win 7 could be booted from grub before the update, though. In short, nothing on the grub menu works. any solutions? The grub menu changed appearance - before it was on a purple background, small letters, now it's white-on-black, big letters, looking very basic. The original installation was from a usb-drive, and I hadn't heard about wubi until I started googling this problem, so I doubt there's any connection. I really hope there are some grub-savvy people out there :) EDIT: ok. so, I made a bootable usb, and am running from that right now. when I ran the bootinfoscript, it warned me that "gawk" could not be found, using "busybox awk" instead. This may lead to unreliable results. just so you know. The contents of RESULTS.txt are: Boot Info Script 0.61 [1 April 2012] ============================= Boot Info Summary: =============================== => Windows is installed in the MBR of /dev/sda. => Grub2 (v1.99) is installed in the MBR of /dev/sdb and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos3)/boot/grub on this drive. => Syslinux MBR (4.04 and higher) is installed in the MBR of /dev/sdc. sda1: __________________________________________ File system: vfat Boot sector type: Dell Utility: FAT16 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: /DELLBIO.BIN /DELLRMK.BIN /COMMAND.COM sda2: __________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: sda3: __________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe sda4: __________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sda5: __________________________________________ File system: vfat Boot sector type: Windows 7: FAT32 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows XP Boot files: /boot.ini /bootmgr /ntldr /NTDETECT.COM sdb1: __________________________________________ File system: ntfs Boot sector type: Windows XP: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: sdb2: __________________________________________ File system: swap Boot sector type: - Boot sector info: sdb3: __________________________________________ File system: ext4 Boot sector type: Grub2 (v1.99) Boot sector info: Grub2 (v1.99) is installed in the boot sector of sdb3 and looks at sector 375893584 of the same hard drive for core.img. core.img is at this location and looks for (,msdos3)/boot/grub on this drive. Operating System: Ubuntu 12.04 LTS Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdb4: __________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Boot files: sdc1: __________________________________________ File system: ntfs Boot sector type: SYSLINUX 4.06 4.06-pre1 Boot sector info: Syslinux looks at sector 4649656 of /dev/sdc1 for its second stage. SYSLINUX is installed in the directory. The integrity check of the ADV area failed. No errors found in the Boot Parameter Block. Operating System: Boot files: /boot/grub/grub.cfg /syslinux/syslinux.cfg /ldlinux.sys ============================ Drive/Partition Info: ============================= Drive: sda _______________________________________ Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 63 240,974 240,912 de Dell Utility /dev/sda2 241,664 21,213,183 20,971,520 7 NTFS / exFAT / HPFS /dev/sda3 * 21,213,184 483,151,863 461,938,680 7 NTFS / exFAT / HPFS /dev/sda4 483,151,872 488,394,751 5,242,880 f W95 Extended (LBA) /dev/sda5 483,153,920 488,394,751 5,240,832 dd Dell Media Direct Drive: sdb _______________________________________ Disk /dev/sdb: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdb1 63 345,886,749 345,886,687 7 NTFS / exFAT / HPFS /dev/sdb2 345,888,768 361,510,911 15,622,144 82 Linux swap / Solaris /dev/sdb3 * 361,510,912 390,807,786 29,296,875 83 Linux /dev/sdb4 390,809,600 488,394,751 97,585,152 83 Linux Drive: sdc _______________________________________ Disk /dev/sdc: 8015 MB, 8015282176 bytes 255 heads, 63 sectors/track, 974 cylinders, total 15654848 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdc1 * 2,048 15,652,863 15,650,816 7 NTFS / exFAT / HPFS "blkid" output: ____________________________________ Device UUID TYPE LABEL /dev/loop0 squashfs /dev/sda1 07D8-0411 vfat DellUtility /dev/sda2 E2765BBC765B9061 ntfs RECOVERY /dev/sda3 98DC5E54DC5E2D2E ntfs OS /dev/sda5 7061-9DF5 vfat MEDIADIRECT /dev/sdb1 01CBBB4C3374C3B0 ntfs Data1 /dev/sdb2 1ca45f3f-f888-43d1-8137-02699597189a swap /dev/sdb3 6bc1b599-ad4b-403c-a155-a5bc81211f5e ext4 /dev/sdb4 58e2b257-8608-4b11-b20b-dc162bb80b62 ext4 /dev/sdc1 0C02B64402B63316 ntfs PENDRIVE ================================ Mount points: ================================= Device Mount_Point Type Options /dev/loop0 /rofs squashfs (ro,noatime) /dev/sdb4 /media/58e2b257-8608-4b11-b20b-dc162bb80b62 ext4 (rw,nosuid,nodev,uhelper=udisks) /dev/sdc1 /cdrom fuseblk (rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096) ================================ sda5/boot.ini: ================================ [boot loader] timeout=0 default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Embedded" /fastdetect /KERNEL=NTOSBOOT.EXE /maxmem=1024 =========================== sdb3/boot/grub/grub.cfg: =========================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="$1" if [ "$1" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 3.2.0-24-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e linux /boot/vmlinuz-3.2.0-24-generic root=UUID=6bc1b599-ad4b-403c-a155-a5bc81211f5e ro quiet splash $vt_handoff initrd /boot/initrd.img-3.2.0-24-generic } menuentry 'Ubuntu, with Linux 3.2.0-24-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e echo 'Loading Linux 3.2.0-24-generic ...' linux /boot/vmlinuz-3.2.0-24-generic root=UUID=6bc1b599-ad4b-403c-a155-a5bc81211f5e ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.2.0-24-generic } submenu "Previous Linux versions" { menuentry 'Ubuntu, with Linux 3.0.0-19-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e linux /boot/vmlinuz-3.0.0-19-generic root=UUID=6bc1b599-ad4b-403c-a155-a5bc81211f5e ro quiet splash $vt_handoff initrd /boot/initrd.img-3.0.0-19-generic } menuentry 'Ubuntu, with Linux 3.0.0-19-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e echo 'Loading Linux 3.0.0-19-generic ...' linux /boot/vmlinuz-3.0.0-19-generic root=UUID=6bc1b599-ad4b-403c-a155-a5bc81211f5e ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.0.0-19-generic } } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows 7 (loader) (on /dev/sda3)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos3)' search --no-floppy --fs-uuid --set=root 98DC5E54DC5E2D2E chainloader +1 } menuentry "Microsoft Windows XP Embedded (on /dev/sda5)" --class windows --class os { insmod part_msdos insmod fat set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root 7061-9DF5 drivemap -s (hd0) ${root} chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### =============================== sdb3/etc/fstab: ================================ # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sdb3 during installation UUID=6bc1b599-ad4b-403c-a155-a5bc81211f5e / ext4 errors=remount-ro 0 1 # /home was on /dev/sdb4 during installation UUID=58e2b257-8608-4b11-b20b-dc162bb80b62 /home ext4 defaults,user_xattr 0 2 # swap was on /dev/sdb2 during installation UUID=1ca45f3f-f888-43d1-8137-02699597189a none swap sw 0 0 =================== sdb3: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) = boot/grub/core.img 1 = boot/grub/grub.cfg 1 = boot/initrd.img-3.0.0-19-generic 2 = boot/initrd.img-3.2.0-24-generic 2 = boot/vmlinuz-3.0.0-19-generic 2 = boot/vmlinuz-3.2.0-24-generic 1 = vmlinuz 1 = vmlinuz.old 2 =========================== sdc1/boot/grub/grub.cfg: =========================== if loadfont /boot/grub/font.pf2 ; then set gfxmode=auto insmod efi_gop insmod efi_uga insmod gfxterm terminal_output gfxterm fi set menu_color_normal=white/black set menu_color_highlight=black/light-gray menuentry "Try Ubuntu without installing" { set gfxpayload=keep linux /casper/vmlinuz file=/cdrom/preseed/ubuntu.seed boot=casper quiet splash -- initrd /casper/initrd.lz } menuentry "Install Ubuntu" { set gfxpayload=keep linux /casper/vmlinuz file=/cdrom/preseed/ubuntu.seed boot=casper only-ubiquity quiet splash -- initrd /casper/initrd.lz } menuentry "Check disc for defects" { set gfxpayload=keep linux /casper/vmlinuz boot=casper integrity-check quiet splash -- initrd /casper/initrd.lz } ========================= sdc1/syslinux/syslinux.cfg: ========================== # D-I config version 2.0 include menu.cfg default vesamenu.c32 prompt 0 timeout 50 # If you would like to use the new menu and be presented with the option to install or run from USB at startup, remove # from the following line. This line was commented out (by request of many) to allow the old menu to be presented and to enable booting straight into the Live Environment! # ui gfxboot bootlogo =================== sdc1: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) ?? = ?? boot/grub/grub.cfg 0 ================= sdc1: Location of files loaded by Syslinux: ================== GiB - GB File Fragment(s) ?? = ?? ldlinux.sys 1 ?? = ?? syslinux/chain.c32 1 ?? = ?? syslinux/gfxboot.c32 1 ?? = ?? syslinux/syslinux.cfg 0 ?? = ?? syslinux/vesamenu.c32 1 ============== sdc1: Version of COM32(R) files used by Syslinux: =============== syslinux/chain.c32 : COM32R module (v4.xx) syslinux/gfxboot.c32 : COM32R module (v4.xx) syslinux/vesamenu.c32 : COM32R module (v4.xx) =============================== StdErr Messages: =============================== xz: (stdin): Compressed data is corrupt xz: (stdin): Compressed data is corrupt awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in ./bootinfoscript: line 1646: [: 2.73495e+09: integer expression expected

  Read the article

• apt-get is broken

  - by Amol Shinde

  I Cannot install any package in the server, As I am newbie in Server. In Morning I found that some, I am not able to install any package from command line in the server,Now every package is now manually downloaded packages and then installed in the server. Can any one Please tell me what is the issue and how could it be resolved. OS:- Ubuntu 10.04.4 LTS \n \l (64 Bit) Below is the error: iam@ubuntu$ sudo apt-get install pidgin Reading package lists... Done Building dependency tree Reading state information... Done pidgin is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 102 not upgraded. 32 not fully installed or removed. After this operation, 0B of additional disk space will be used. Traceback (most recent call last): File "/usr/bin/apt-listchanges", line 33, in <module> from ALChacks import * File "/usr/share/apt-listchanges/ALChacks.py", line 32, in <module> sys.stderr.write(_("Can't set locale; make sure $LC_* and $LANG are correct!\n")) NameError: name '_' is not defined perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LC_CTYPE = "UTF-8", LANG = "en_IN" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory Setting up shared-mime-info (0.71-1ubuntu2) ... /var/lib/dpkg/info/shared-mime-info.postinst: line 13: 21935 Segmentation fault update-mime-database.real /usr/share/mime dpkg: error processing shared-mime-info (--configure): subprocess installed post-installation script returned error exit status 139 dpkg: dependency problems prevent configuration of libgtk2.0-0: libgtk2.0-0 depends on shared-mime-info; however: Package shared-mime-info is not configured yet. dpkg: error processing libgtk2.0-0 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of chromium-browser: chromium-browser depends on libgtk2.0-0 (>= 2.20.0); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing chromium-browser (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of chromium-codecs-ffmpeg: chromium-codecs-ffmpeg depends on chromium-browser (>= 4.0.203.0~); however: Package chromium-browser is not configured yet. dpkg: error processing chromium-codecs-ffmpeg (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of chromium-browser-l10n: chromium-browser-l10n depends on chromium-browser (= 18.0.1025.151~r130497-0ubuntu0.10.04.No apport report written because the error message indicates its a followup error from a previous failure. No apport report written because the error message indicates its a followup error from a previous failure. No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already 1); however: Package chromium-browser is not configured yet. dpkg: error processing chromium-browser-l10n (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libevdocument2: libevdocument2 depends on libgtk2.0-0 (>= 2.14.0); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing libevdocument2 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libevview2: libevview2 depends on libevdocument2 (>= 2.29.5); however: Package libevdocument2 is not configured yet. libevview2 depends on libgtk2.0-0 (>= 2.20.0); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing libevview2 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of evince: evince depends on libevdocument2 (>= 2.29.5); however: Package libevdocument2 is not configured yet. evince depends on libevview2 (>= 2.29.No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already 5); however: Package libevview2 is not configured yet. evince depends on libgtk2.0-0 (>= 2.16.0); however: Package libgtk2.0-0 is not configured yet. evince depends on shared-mime-info; however: Package shared-mime-info is not configured yet. dpkg: error processing evince (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of firefox: firefox depends on libgtk2.0-0 (>= 2.20.0); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing firefox (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of gcalctool: gcalctool depends on libgtk2.0-0 (>= 2.18.0); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing gcalctool (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libgdict-1.0-6: libgdict-1.0-6 depends on libgtk2.0-0 (>= 2.18.0); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing libgdict-1.0-6 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of gnome-utils: gnome-utils depends on libgdict-1.0-6 (>= 2.23.90); however: Package libgdict-1.0-6 is not configured yet. gnome-utils depends on libgtk2.0-0 (>= 2.18.0); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing gnome-utils (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of gtk2-engines-pixbuf: gtk2-engines-pixbuf depends on gtk2.0-binver-2.10.0; however: Package gtk2.0-binver-2.10.0 is not installed. Package libgtk2.0-0 which provides gtk2.0-binver-2.10.0 is not configured yet. gtk2-engines-pixbuf depends on libgtk2.0-0 (= 2.20.1-0ubuntu2.1); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing gtk2-engines-pixbuf (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libedataserverui1.2-8: libedataserverui1.2-8 depends on libgtk2.0-0 (>= 2.14.0); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing libedataserverui1.2-8 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libgail18: libgail18 depends on libgtk2.0-0 (= 2.20.1-0ubuntu2.1); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing libgail18 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libgtk2.0-bin: libgtk2.0-bin depends on libgtk2.0-0 (>= 2.20.1-0ubuntu2.1); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing libgtk2.0-bin (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libgtk2.0-dev: libgtk2.0-dev depends on libgtk2.0-0 (= 2.20.1-0ubuntu2.1); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing libgtk2.0-dev (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libnotify-dev: libnotify-dev depends on libgtk2.0-dev (>= 2.10); however: Package libgtk2.0-dev is not configured yet. dpkg: error processing libnotify-dev (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of network-manager-gnome: network-manager-gnome depends on libgtk2.0-0 (>= 2.16.0); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing network-manager-gnome (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of openoffice.org-core: openoffice.org-core depends on libgtk2.0-0 (>= 2.10); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing openoffice.org-core (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of openoffice.org-draw: openoffice.org-draw depends on openoffice.org-core (= 1:3.2.0-7ubuntu4.4); however: Package openoffice.org-core is not configured yet. dpkg: error processing openoffice.org-draw (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of openoffice.org-impress: openoffice.org-impress depends on openoffice.org-core (= 1:3.2.0-7ubuntu4.4); however: Package openoffice.org-core is not configured yet. openoffice.org-impress depends on openoffice.org-draw (= 1:3.2.0-7ubuntu4.4); however: Package openoffice.org-draw is not configured yet. dpkg: error processing openoffice.org-impress (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of pidgin: pidgin depends on libgtk2.0-0 (>= 2.18.0); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing pidgin (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already Setting up update-manager (1:0.134.12.1) ... locale: Cannot set LC_CTYPE to default locale: No such file or directory dpkg: error processing update-manager (--configure): subprocess installed post-installation script returned error exit status 245 No apport report written because MaxReports is reached already dpkg: dependency problems prevent configuration of update-notifier: update-notifier depends on libgtk2.0-0 (>= 2.14.0); however: Package libgtk2.0-0 is not configured yet. update-notifier depends on update-manager; however: Package update-manager is not configured yet. dpkg: error processing update-notifier (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already dpkg: dependency problems prevent configuration of xulrunner-1.9.2: xulrunner-1.9.2 depends on libgtk2.0-0 (>= 2.18.0); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing xulrunner-1.9.2 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of xulrunner-1.9.2-dev: xulrunner-1.9.2-dev depends on xulrunner-1.9.2 (= 1.9.2.28+build1+nobinonly-0ubuntu0.10.04.1); however: Package xulrunner-1.9.2 is not configured yet. xulrunner-1.9.2-dev depends on libnotify-dev; however: Package libnotify-dev is not configured yet. dpkg: error processing xulrunner-1.9.2-dev (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already dpkg: dependency problems prevent configuration of icedtea6-plugin: icedtea6-plugin depends on xulrunner-1.9.2; however: Package xulrunner-1.9.2 is not configured yet. icedtea6-plugin depends on libgtk2.0-0 (>= 2.8.0); however: Package libgtk2.0-0 is not configured yet. dpkg: error processing icedtea6-plugin (--configure): dependency problems - leaving unconfigured Setting up libgweather-common (2.30.0-0ubuntu1.1) ... No apport report written because MaxReports is reached already locale: Cannot set LC_CTYPE to default locale: No such file or directory dpkg: error processing libgweather-common (--configure): subprocess installed post-installation script returned error exit status 245 No apport report written because MaxReports is reached already dpkg: dependency problems prevent configuration of libgweather1: libgweather1 depends on libgtk2.0-0 (>= 2.11.0); however: Package libgtk2.0-0 is not configured yet. libgweather1 depends on libgweather-common (>= 2.24.0); however: Package libgweather-common is not configured yet. dpkg: error processing libgweather1 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of openoffice.org-style-galaxy: openoffice.org-style-galaxy depends on openoffice.org-core (>= 1:3.2.0~beta); however: Package openoffice.org-core is not configured yet. No apport report written because MaxReports is reached already dpkg: error processing openoffice.org-style-galaxy (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of openoffice.org-common: openoffice.org-common depends on openoffice.org-style-default | openoffice.org-style; however: Package openoffice.org-style-default is not installed. Package openoffice.org-style-galaxy which provides openoffice.org-style-default is not configured yet. Package openoffice.org-style is not installed. Package openoffice.org-style-galaxy which provides openoffice.org-style is not configured yet. No apport report written because MaxReports is reached already dpkg: error processing openoffice.org-common (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already Errors were encountered while processing: shared-mime-info libgtk2.0-0 chromium-browser chromium-codecs-ffmpeg chromium-browser-l10n libevdocument2 libevview2 evince firefox gcalctool libgdict-1.0-6 gnome-utils gtk2-engines-pixbuf libedataserverui1.2-8 libgail18 libgtk2.0-bin libgtk2.0-dev libnotify-dev network-manager-gnome openoffice.org-core openoffice.org-draw openoffice.org-impress pidgin update-manager update-notifier xulrunner-1.9.2 xulrunner-1.9.2-dev icedtea6-plugin libgweather-common libgweather1 openoffice.org-style-galaxy openoffice.org-common E: Sub-process /usr/bin/dpkg returned an error code (1) While typing command in terminal, command is not auto-completing.

  Read the article

• VMware Player 4.04 on Ubuntu 12.04 will not compile

  - by stephen mew

  I installed VMware-Player-4.0.4-744019.i386.bundle onto Ubuntu 11.10. This worked fine. I then upgraded to Ubuntu 12.04 The upgrade appeared to be successful. I then tried to start VMware Player and I got a popup "VMware Kernel Module Updater" I accept the process (click Install) The updater process runs, the output of which is; Stopping VMWare Services [green tick] Virtual Machine Monitor [RED exclamation mark] Virtual Network Device [green tick] VMware Blocking Filesystem [green tick] Virtual Machine Communication Interface [green tick] VMCI Sockets Error popup; Unable to start services See log file /tmp/vmware-root/modconfig-11912.log" Looking in the log file It seems that these are the complaints. 2012-07-11T15:35:19.829Z| vthread-3| I120: Failed to find /lib/modules/preferred/build/include/linux/version.h 2012-07-11T15:35:19.829Z| vthread-3| I120: Failed version test: /lib/modules/preferred/build/include/linux/version.h 2012-07-11T15:35:49.683Z| vthread-3| I120: Failed to compile module vmnet! I tried the patch for 4.0.3 and it did not work. Can anyone point me in the right direction here ? log file; 2012-07-11T15:35:18.618Z| vthread-3| I120: Log for VMware Workstation pid=11912 version=8.0.4 build=build-744019 option=Release 2012-07-11T15:35:18.618Z| vthread-3| I120: The process is 32-bit. 2012-07-11T15:35:18.618Z| vthread-3| I120: Host codepage=UTF-8 encoding=UTF-8 2012-07-11T15:35:18.618Z| vthread-3| I120: Host is Linux 3.2.0-26-generic Ubuntu 12.04 LTS 2012-07-11T15:35:18.616Z| vthread-3| I120: Msg_Reset: 2012-07-11T15:35:18.616Z| vthread-3| I120: [msg.dictionary.load.openFailed] Cannot open file "/usr/lib/vmware/settings": No such file or directory. 2012-07-11T15:35:18.616Z| vthread-3| I120: ---------------------------------------- 2012-07-11T15:35:18.616Z| vthread-3| I120: PREF Optional preferences file not found at /usr/lib/vmware/settings. Using default values. 2012-07-11T15:35:18.617Z| vthread-3| I120: Msg_Reset: 2012-07-11T15:35:18.617Z| vthread-3| I120: [msg.dictionary.load.openFailed] Cannot open file "/root/.vmware/config": No such file or directory. 2012-07-11T15:35:18.617Z| vthread-3| I120: ---------------------------------------- 2012-07-11T15:35:18.617Z| vthread-3| I120: PREF Optional preferences file not found at /root/.vmware/config. Using default values. 2012-07-11T15:35:18.617Z| vthread-3| I120: Msg_Reset: 2012-07-11T15:35:18.617Z| vthread-3| I120: [msg.dictionary.load.openFailed] Cannot open file "/root/.vmware/preferences": No such file or directory. 2012-07-11T15:35:18.617Z| vthread-3| I120: ---------------------------------------- 2012-07-11T15:35:18.617Z| vthread-3| I120: PREF Failed to load user preferences. 2012-07-11T15:35:18.618Z| vthread-3| W110: Logging to /tmp/vmware-root/modconfig-11912.log 2012-07-11T15:35:19.054Z| vthread-3| I120: modconf query interface initialized 2012-07-11T15:35:19.056Z| vthread-3| I120: modconf library initialized 2012-07-11T15:35:19.158Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:19.168Z| vthread-3| I120: Validating path /lib/modules/preferred/build/include for kernel release 3.2.0-26-generic 2012-07-11T15:35:19.168Z| vthread-3| I120: Failed to find /lib/modules/preferred/build/include/linux/version.h 2012-07-11T15:35:19.168Z| vthread-3| I120: Failed version test: /lib/modules/preferred/build/include/linux/version.h not found. 2012-07-11T15:35:19.168Z| vthread-3| I120: Validating path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic 2012-07-11T15:35:19.175Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:19.201Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:19.291Z| vthread-3| I120: Header path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic is valid. 2012-07-11T15:35:19.292Z| vthread-3| I120: Validating path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic 2012-07-11T15:35:19.296Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:19.326Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:19.417Z| vthread-3| I120: Header path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic is valid. 2012-07-11T15:35:19.480Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.489Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.498Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.507Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.517Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.566Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.575Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.584Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.593Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.602Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.606Z| vthread-3| I120: Validating path /lib/modules/preferred/build/include for kernel release 3.2.0-26-generic 2012-07-11T15:35:19.606Z| vthread-3| I120: Failed to find /lib/modules/preferred/build/include/linux/version.h 2012-07-11T15:35:19.606Z| vthread-3| I120: Failed version test: /lib/modules/preferred/build/include/linux/version.h not found. 2012-07-11T15:35:19.606Z| vthread-3| I120: Validating path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic 2012-07-11T15:35:19.611Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:19.635Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:19.741Z| vthread-3| I120: Header path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic is valid. 2012-07-11T15:35:19.787Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.796Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.805Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.814Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.824Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:19.829Z| vthread-3| I120: Validating path /lib/modules/preferred/build/include for kernel release 3.2.0-26-generic 2012-07-11T15:35:19.829Z| vthread-3| I120: Failed to find /lib/modules/preferred/build/include/linux/version.h 2012-07-11T15:35:19.829Z| vthread-3| I120: Failed version test: /lib/modules/preferred/build/include/linux/version.h not found. 2012-07-11T15:35:19.829Z| vthread-3| I120: Validating path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic 2012-07-11T15:35:19.834Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:19.857Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:19.945Z| vthread-3| I120: Header path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic is valid. 2012-07-11T15:35:25.503Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:25.514Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:25.523Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:25.533Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:25.542Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:26.338Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:26.338Z| vthread-3| I120: Validating path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic 2012-07-11T15:35:26.343Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:26.368Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:26.455Z| vthread-3| I120: Header path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic is valid. 2012-07-11T15:35:26.455Z| vthread-3| I120: Building module vmmon. 2012-07-11T15:35:26.455Z| vthread-3| I120: Extracting the sources of the vmmon module. 2012-07-11T15:35:26.484Z| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmmon-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-26-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-07-11T15:35:35.469Z| vthread-3| I120: Installing module vmmon from /tmp/vmware-root/modules/vmmon.o to /lib/modules/3.2.0-26-generic/misc. 2012-07-11T15:35:35.470Z| vthread-3| I120: Registering file: /usr/lib/vmware-installer/2.0/vmware-installer --register-file vmware-vmx regular /lib/modules/3.2.0-26-generic/misc/vmmon.ko 2012-07-11T15:35:39.713Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:39.713Z| vthread-3| I120: Validating path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic 2012-07-11T15:35:39.719Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:39.753Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:39.845Z| vthread-3| I120: Header path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic is valid. 2012-07-11T15:35:39.845Z| vthread-3| I120: Building module vmnet. 2012-07-11T15:35:39.846Z| vthread-3| I120: Extracting the sources of the vmnet module. 2012-07-11T15:35:39.913Z| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmnet-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-26-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-07-11T15:35:49.683Z| vthread-3| I120: Failed to compile module vmnet! 2012-07-11T15:35:49.704Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:35:49.705Z| vthread-3| I120: Validating path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic 2012-07-11T15:35:49.729Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:49.874Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:35:49.961Z| vthread-3| I120: Header path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic is valid. 2012-07-11T15:35:49.961Z| vthread-3| I120: Building module vmblock. 2012-07-11T15:35:49.961Z| vthread-3| I120: Extracting the sources of the vmblock module. 2012-07-11T15:35:50.159Z| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmblock-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-26-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-07-11T15:35:59.283Z| vthread-3| I120: Installing module vmblock from /tmp/vmware-root/modules/vmblock.o to /lib/modules/3.2.0-26-generic/misc. 2012-07-11T15:35:59.284Z| vthread-3| I120: Registering file: /usr/lib/vmware-installer/2.0/vmware-installer --register-file vmware-vmx regular /lib/modules/3.2.0-26-generic/misc/vmblock.ko 2012-07-11T15:36:04.318Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:36:04.319Z| vthread-3| I120: Validating path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic 2012-07-11T15:36:04.324Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:36:04.344Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:36:04.427Z| vthread-3| I120: Header path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic is valid. 2012-07-11T15:36:04.427Z| vthread-3| I120: Building module vmci. 2012-07-11T15:36:04.428Z| vthread-3| I120: Extracting the sources of the vmci module. 2012-07-11T15:36:04.456Z| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmci-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-26-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-07-11T15:36:15.728Z| vthread-3| I120: Installing module vmci from /tmp/vmware-root/modules/vmci.o to /lib/modules/3.2.0-26-generic/misc. 2012-07-11T15:36:15.730Z| vthread-3| I120: Registering file: /usr/lib/vmware-installer/2.0/vmware-installer --register-file vmware-vmx regular /lib/modules/3.2.0-26-generic/misc/vmci.ko 2012-07-11T15:36:20.349Z| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-26-generic. 2012-07-11T15:36:20.350Z| vthread-3| I120: Validating path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic 2012-07-11T15:36:20.355Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:36:20.378Z| vthread-3| I120: Your GCC version: 4.6 2012-07-11T15:36:20.464Z| vthread-3| I120: Header path /lib/modules/3.2.0-26-generic/build/include for kernel release 3.2.0-26-generic is valid. 2012-07-11T15:36:20.464Z| vthread-3| I120: Building module vmci. 2012-07-11T15:36:20.464Z| vthread-3| I120: Extracting the sources of the vmci module. 2012-07-11T15:36:20.514Z| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmci-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-26-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-07-11T15:36:22.732Z| vthread-3| I120: Building module vsock. 2012-07-11T15:36:22.732Z| vthread-3| I120: Extracting the sources of the vsock module. 2012-07-11T15:36:22.783Z| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vsock-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-26-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-07-11T15:36:33.825Z| vthread-3| I120: Installing module vsock from /tmp/vmware-root/modules/vsock.o to /lib/modules/3.2.0-26-generic/misc. 2012-07-11T15:36:33.826Z| vthread-3| I120: Registering file: /usr/lib/vmware-installer/2.0/vmware-installer --register-file vmware-vmx regular /lib/modules/3.2.0-26-generic/misc/vsock.ko

  Read the article

• Grub 'Read Error' - Only Loads with LiveCD

  - by Ryan Sharp

  Problem After installing Ubuntu to complete my Windows 7/Ubuntu 12.04 dual-boot setup, Grub just wouldn't load at all unless I boot from the LiveCD. Afterwards, everything works completely normal. However, this workaround isn't a solution and I'd like to be able to boot without the aid of a disc. Fdisk -l Using the fdisk -l command, I am given the following: Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x324971d1 Device Boot Start End Blocks Id System /dev/sda1 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 208896 48957439 24374272 7 HPFS/NTFS/exFAT /dev/sda3 * 48959486 124067839 37554177 5 Extended /dev/sda5 48959488 124067839 37554176 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc0ee6a69 Device Boot Start End Blocks Id System /dev/sdb1 1024208894 1953523711 464657409 5 Extended /dev/sdb3 * 2048 1024206847 512102400 7 HPFS/NTFS/exFAT /dev/sdb5 1024208896 1937897471 456844288 83 Linux /dev/sdb6 1937899520 1953523711 7812096 82 Linux swap / Solaris Partition table entries are not in disk order Disk /dev/sdc: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x292eee23 Device Boot Start End Blocks Id System /dev/sdc1 2048 625141759 312569856 7 HPFS/NTFS/exFAT Bootinfoscript I've used the BootInfoScript, and received the following output: Boot Info Script 0.61 [1 April 2012] ============================= Boot Info Summary: =============================== => Grub2 (v1.99) is installed in the MBR of /dev/sda and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos5)/boot/grub on this drive. => Grub2 (v1.99) is installed in the MBR of /dev/sdb and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos5)/boot/grub on this drive. => Windows is installed in the MBR of /dev/sdc. sda1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: /bootmgr /Boot/BCD sda2: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe sda3: __________________________________________________________________________ File system: Extended Partition Boot sector type: Unknown Boot sector info: sda5: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 12.04.1 LTS Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdb1: __________________________________________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sdb5: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Boot files: sdb6: __________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: sdb3: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: According to the info in the boot sector, sdb3 starts at sector 200744960. But according to the info from fdisk, sdb3 starts at sector 2048. According to the info in the boot sector, sdb3 has 823461887 sectors, but according to the info from fdisk, it has 1024204799 sectors. Operating System: Boot files: sdc1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 2,048 206,847 204,800 7 NTFS / exFAT / HPFS /dev/sda2 208,896 48,957,439 48,748,544 7 NTFS / exFAT / HPFS /dev/sda3 * 48,959,486 124,067,839 75,108,354 5 Extended /dev/sda5 48,959,488 124,067,839 75,108,352 83 Linux Drive: sdb _____________________________________________________________________ Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdb1 1,024,208,894 1,953,523,711 929,314,818 5 Extended /dev/sdb5 1,024,208,896 1,937,897,471 913,688,576 83 Linux /dev/sdb6 1,937,899,520 1,953,523,711 15,624,192 82 Linux swap / Solaris /dev/sdb3 * 2,048 1,024,206,847 1,024,204,800 7 NTFS / exFAT / HPFS Drive: sdc _____________________________________________________________________ Disk /dev/sdc: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdc1 2,048 625,141,759 625,139,712 7 NTFS / exFAT / HPFS "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/sda1 A48056DF8056B80E ntfs System Reserved /dev/sda2 A8C6D6A4C6D671D4 ntfs Windows /dev/sda5 fd71c537-3715-44e1-b1fe-07537e22b3dd ext4 /dev/sdb3 6373D03D0A3747A8 ntfs Steam /dev/sdb5 6f5a6eb3-a932-45aa-893e-045b57708270 ext4 /dev/sdb6 469848c8-867a-41b7-b0e1-b813a43c64af swap /dev/sdc1 725D7B961CF34B1B ntfs backup ================================ Mount points: ================================= Device Mount_Point Type Options /dev/sda5 / ext4 (rw,noatime,nodiratime,discard,errors=remount-ro) /dev/sdb5 /home ext4 (rw) =========================== sda5/boot/grub/grub.cfg: =========================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd set locale_dir=($root)/boot/grub/locale set lang=en_GB insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="${1}" if [ "${1}" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ "${recordfail}" != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "${linux_gfx_mode}" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 3.2.0-29-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd linux /boot/vmlinuz-3.2.0-29-generic root=UUID=fd71c537-3715-44e1-b1fe-07537e22b3dd ro quiet splash $vt_handoff initrd /boot/initrd.img-3.2.0-29-generic } menuentry 'Ubuntu, with Linux 3.2.0-29-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd echo 'Loading Linux 3.2.0-29-generic ...' linux /boot/vmlinuz-3.2.0-29-generic root=UUID=fd71c537-3715-44e1-b1fe-07537e22b3dd ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.2.0-29-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows 7 (loader) (on /dev/sda1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root A48056DF8056B80E chainloader +1 } menuentry "Windows 7 (loader) (on /dev/sda2)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root A8C6D6A4C6D671D4 chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### -------------------------------------------------------------------------------- =============================== sda5/etc/fstab: ================================ -------------------------------------------------------------------------------- # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda5 during installation UUID=fd71c537-3715-44e1-b1fe-07537e22b3dd / ext4 noatime,nodiratime,discard,errors=remount-ro 0 1 # /home was on /dev/sdb5 during installation UUID=6f5a6eb3-a932-45aa-893e-045b57708270 /home ext4 defaults 0 2 # swap was on /dev/sdb6 during installation UUID=469848c8-867a-41b7-b0e1-b813a43c64af none swap sw 0 0 tmpfs /tmp tmpfs defaults,noatime,mode=1777 0 0 -------------------------------------------------------------------------------- =================== sda5: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) = boot/grub/core.img 1 = boot/grub/grub.cfg 1 = boot/initrd.img-3.2.0-29-generic 2 = boot/vmlinuz-3.2.0-29-generic 1 = initrd.img 2 = vmlinuz 1 ======================== Unknown MBRs/Boot Sectors/etc: ======================== Unknown BootLoader on sda3 00000000 63 6f 70 69 61 20 65 20 63 6f 6c 61 41 63 65 64 |copia e colaAced| 00000010 65 72 20 61 20 74 6f 64 6f 20 6f 20 74 65 78 74 |er a todo o text| 00000020 6f 20 66 61 6c 61 64 6f 20 75 74 69 6c 69 7a 61 |o falado utiliza| 00000030 6e 64 6f 20 61 20 63 6f 6e 76 65 72 73 c3 a3 6f |ndo a convers..o| 00000040 20 64 65 20 74 65 78 74 6f 20 70 61 72 61 20 76 | de texto para v| 00000050 6f 7a 4d 61 6e 69 70 75 6c 61 72 20 61 73 20 64 |ozManipular as d| 00000060 65 66 69 6e 69 c3 a7 c3 b5 65 73 20 71 75 65 20 |efini....es que | 00000070 63 6f 6e 74 72 6f 6c 61 6d 20 6f 20 61 63 65 73 |controlam o aces| 00000080 73 6f 20 64 65 20 57 65 62 73 69 74 65 73 20 61 |so de Websites a| 00000090 20 63 6f 6f 6b 69 65 73 2c 20 4a 61 76 61 53 63 | cookies, JavaSc| 000000a0 72 69 70 74 20 65 20 70 6c 75 67 2d 69 6e 73 4d |ript e plug-insM| 000000b0 61 6e 69 70 75 6c 61 72 20 61 73 20 64 65 66 69 |anipular as defi| 000000c0 6e 69 c3 a7 c3 b5 65 73 20 72 65 6c 61 63 69 6f |ni....es relacio| 000000d0 6e 61 64 61 73 20 63 6f 6d 20 70 72 69 76 61 63 |nadas com privac| 000000e0 69 64 61 64 65 41 63 65 64 65 72 20 61 6f 73 20 |idadeAceder aos | 000000f0 73 65 75 73 20 70 65 72 69 66 c3 a9 72 69 63 6f |seus perif..rico| 00000100 73 20 55 53 42 55 74 69 6c 69 7a 61 72 20 6f 20 |s USBUtilizar o | 00000110 73 65 75 20 6d 69 63 72 6f 66 6f 6e 65 55 74 69 |seu microfoneUti| 00000120 6c 69 7a 61 72 20 61 20 73 75 61 20 63 c3 a2 6d |lizar a sua c..m| 00000130 61 72 61 55 74 69 6c 69 7a 61 72 20 6f 20 73 65 |araUtilizar o se| 00000140 75 20 6d 69 63 72 6f 66 6f 6e 65 20 65 20 61 20 |u microfone e a | 00000150 63 c3 a2 6d 61 72 61 4e c3 a3 6f 20 66 6f 69 20 |c..maraN..o foi | 00000160 70 6f 73 73 c3 ad 76 65 6c 20 65 6e 63 6f 6e 74 |poss..vel encont| 00000170 72 61 72 20 6f 20 63 61 6d 69 6e 68 6f 20 61 62 |rar o caminho ab| 00000180 73 6f 6c 75 74 6f 20 70 61 72 61 20 6f 20 64 69 |soluto para o di| 00000190 72 65 63 74 c3 b3 72 69 6f 20 61 20 65 6d 70 61 |rect..rio a empa| 000001a0 63 6f 74 61 72 2e 4f 20 64 69 72 65 63 74 c3 b3 |cotar.O direct..| 000001b0 72 69 6f 20 64 65 20 65 6e 74 72 61 64 61 00 fe |rio de entrada..| 000001c0 ff ff 83 fe ff ff 02 00 00 00 00 10 7a 04 00 00 |............z...| 000001d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 000001f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 55 aa |..............U.| 00000200 =============================== StdErr Messages: =============================== xz: (stdin): Compressed data is corrupt xz: (stdin): Compressed data is corrupt awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in Begging / Appreciation ;) If anything else is required to solve my problem, please ask. My only hopes are that I can solve this, and that doing so won't require re-installation of Grub due to how complicated the procedures are, or that I would be needed to reinstall the OS', as I have done so about six times already since friday due to several other issues I've encountered. Thank you, and good day. System Ubuntu 12.04 64-bit / Windows 7 SP1 64-bit 64GB SSD as boot/OS drive, 1TB HDD as /Home Swap and Steam drive.

  Read the article

• MSCC: Global Windows Azure Bootcamp

  Mauritius participated and contributed to the Global Windows Azure Bootcamp 2014 (GWAB). Again! And this time stronger than ever, and together with 137 other locations in 56 countries world-wide. We had 62 named registrations, 7 guest additions and approximately 10 offline participants prior to the event day. Most interestingly the organisation of the GWAB through the MSCC helped to increased the number of craftsmen. The Mauritius Software Craftsmanship Community has currently 138 registered members - in less than one year! Only with those numbers we can proudly say that all the preparations and hard work towards this event already paid off. Personally, I'm really grateful that we had this kind of response and the feedback from some attendees confirmed that the MSCC is on the right track here on Cyber Island Mauritius. Inspired and motivated by the success of this event, rest assured that there will be more public events like the GWAB. This time it took some time to reflect on our meetup, following my first impression right on spot: "Wow, what an experience to organise and participate in this global event. Overall, I've been very pleased with the preparations and the event itself. Surely, there have been some nicks that we have to address and to improve for future activities like this. Quite frankly, we are not professional event organisers (not yet) but we learned a lot over the past couple of days. A big Thank You to our event sponsors, namely Microsoft Indian Ocean Islands & French Pacific, Ceridian Mauritius and Emtel. Without them this event wouldn't have happened - Thank You! And to the cool team members of Microsoft Student Partners (MSPs). You geeks did a great job! Thanks!" So, how many attendees did we actually have? 61! - Awesome - 61 cloud computing instances to help on the research of diabetes. During Saturday afternoon there was even an online publication on L'Express: Les développeurs mauriciens se joignent au combat contre le diabète Reactions of other attendees Don't take my word for granted... Here are some impressions and feedback from our participants: "Awesome event, really appreciated the presentations :-)" -- Kevin on event comments "very interesting and enriching." -- Diana on event comments "#gwab #gwabmru 2014 great success. Looking forward for gwab 2015" -- Wasiim on Twitter "Was there till the end. Awesome Event. I'll surely join upcoming meetup sessions :)" -- Luchmun on event comments "#gwabmru was not that cool. left early" -- Mohammad on Twitter The overall feedback is positive but we are absolutely aware that there quite a number of problems we had to face. We are already looking into that and ideas / action plans on how we will be able to improve it for future events. The sessions We started the day with welcoming speeches by Thierry Coret, Sr. Marketing Manager of Microsoft Indian Ocean Islands & French Pacific and Vidia Mooneegan, Managing Director and Sr. Vice President of Ceridian Mauritius. The clear emphasis was on the endless possibilities of cloud computing and how it can enable any kind of sectors here in the country. Then it was about time to set up the cloud computing services in order to contribute each attendees cloud computing resources to the global research of diabetes, a step by step guide presented by Arnaud Meslier, Technical Evangelist at Microsoft. Given a rendering package and a configuration file it was very interesting to follow the single steps in Windows Azure. Also, during the day we were not sure whether the set up had been correctly, as Mauritius didn't show up on the results board - which should have been the case after approximately 20 to 30 minutes. Anyways, let the minions work... Next, Arnaud gave a brief overview of the variety of services Windows Azure has to offer. Whether you need a development environment for your websites or mobiles app, running a virtual machine with your existing applications or simply putting a SQL database online. No worries, Windows Azure has the right packages available and the online management portal is really easy t handle. After this, we got a little bit more business oriented while Wasiim Hosenbocus, employee at Ceridian, took the attendees through the inerts of a real-life application, and demoed a couple of the existing features. He did a great job by showing how the different services of Windows Azure can be created and pulled together. After the lunch break it is always tough to keep the audience awake... And it was my turn. I gave a brief overview on operating and managing a SQL database on Windows Azure. Well, there are actually two options available and depending on your individual requirements you should be aware of both. The simpler version is called SQL Database and while provisioning only takes a couple of seconds, you should take into consideration that SQL Database has a number of constraints, like limitations on the actual database size - up to 5 GB as web edition and up to 150 GB maximum as business edition -, among others. Next, it was Chervine Bhiwoo's session on Windows Azure Mobile Services. It was absolutely amazing to see that the mobiles services directly offers you various project templates, like Windows 8 Store App, Android app, iOS app, and even Xamarin cross-platform app development. So, within a couple of minutes you can have your first mobile app active and running on Windows Azure. Furthermore, Chervine showed the attendees that adding another user interface, like Web Sites running on ASP.NET MVC 4 only takes a couple of minutes, too. And last but not least, we rounded up the day with Windows Azure Websites and hosting of Virtual Machines presented by some members of the local Microsoft Students Partners programme. Surely, one of the big advantages using Windows Azure is the availability of pre-defined installation packages of known web applications, like WordPress, Joomla!, or Ghost. Compared to running your own web site with a traditional web hoster it is surely en par, and depending on your personal level of expertise, Windows Azure provides you more liberty in terms of configuration than maybe a shared hosting environment. Running a pre-defined web application is one thing but in case that you would like to have more control over your hosting environment it is highly advised to opt for a virtual machine. Provisioning of an Ubuntu 12.04 LTS system was very simple to do but it takes some more minutes than you might expect. So, please be patient and take your time while Windows Azure gets everything in place for you. Afterwards, you can use a SecureShell (ssh) client like Putty in case of a Linux-based machine, or Remote Desktop Services when operating a Windows Server system to log in into your virtual machine. At the end of the day we had a great Q&A session and we finalised the event with our raffle of goodies. Participation in the raffle was bound to submission of the session survey and most gratefully we had a give-away for everyone. What a nice coincidence to finish of the day. Note: All session slides (and demo codes) will be made available on the MSCC event page. Please, check the Files section over there. (Some) Visual impressions from the event Just to give you an idea about what has happened during the GWAB 2014 at Ebene... Speakers and Microsoft Student Partners are getting ready for the Global Windows Azure Bootcamp 2014 GWAB 2014 attendees are fully integrated into the hands-on-labs and setting up their individuals cloud computing services 60 attendees at the GWAB 2014. Despite some technical difficulties we had a great time running the event GWAB 2014: Using the lunch break for networking and exchange of ideas - Great conversations and topics amongst attendees There are more pictures on the original event page: Questions & Answers Following are a couple of questions which have been asked and didn't get an answer during the event: Q: Is it possible to upload static pages via FTP? A: Yes, you can. Have a look at the right side column on the dashboard of your website. There you'll find information about the FTP and SFTP host names. You can use any FTP client, like ie. FileZilla to log in. FTP also gives you access to your log files. Q: What are the size limitations on SQL Database? A: 5 GB on the Web Edition, and 150 GB on the business edition. A maximum 150 databases (inclusing 'master') per SQL Database server. More details here: General Guidelines and Limitations (Azure SQL Database) Q: What's the maximum size of a SQL Server running in a Virtual Machine? A: The maximum Windows Azure VM has currently 8 CPU cores, 14 or 56 GB of RAM and 16x 1 TB hard drives. More details here: Virtual Machine and Cloud Service Sizes for Azure Q: How can we register for Windows Azure? A: Mauritius is currently not listed for phone verification. Please get in touch with Arnaud Meslier at Microsoft IOI & FP Q: Can I use my own domain name for Windows Azure websites? A: Yes, you can. But this might require to upscale your account to Standard. In case that I missed a question and answer, please use the comment section at the end of the article. Thanks! Final results Every participant was instructed during the hands-on-lab session on how to set up a cloud computing service in their account. Of course, I won't keep the results from you... Global Azure Lab GWAB 2014: Our cloud computing contribution to the research of diabetes And I would say Mauritius did a good job! Upcoming Events What are the upcoming events here in Mauritius? So far, we have the following ones (incomplete list as usual) in chronological order: Launch of Microsoft SQL Server 2014 (15.4.2014) Corsair Hackers Reboot (19.4.2014) WebCup (TBA ~ June 2014) Developers Conference (TBA ~ July 2014) Linuxfest 2014 (TBA ~ November 2014) Hopefully, there will be more announcements during the next couple of weeks and months. If you know about any other event, like a bootcamp, a code challenge or hackathon here in Mauritius, please drop me a note in the comment section below this article. Thanks! Networking and job/project opportunities Despite having technical presentations on Windows Azure an event like this always offers a great bunch of possibilities and opportunities to get in touch with new people in IT, have an exchange of experience with other like-minded people. As I already wrote about Communities - The importance of exchange and discussion - I had a great conversation with representatives of the University des Mascareignes which are currently embracing cloud infrastructure and cloud computing for their various campuses in the Indian Ocean. As for the MSCC it would be a great experience to stay in touch with them, and to work on upcoming, common activities. Furthermore, I had a very good conversation with Thierry and Ludovic of Microsoft IOI & FP on the necessity of user groups and IT communities here on the island. It's great to see that the MSCC is currently on a run and that local companies are sharing our thoughts on promoting IT careers and exchange of IT knowledge in such an open way. I'm also looking forward to be able to participate and to contribute on more events in the near future. My resume of the day We learned a lot today and there is always room for improvement! It was an awesome event and quite frankly it was a pleasure to spend the day with so many enthuastic IT people in the same room. It was a great experience to organise such event locally and participate on a global scale to support the GlyQ-IQ Technology in their research on diabetes. I was so pleased to see the involvement of new MSCC members in taking the opportunity to share and learn about the power of cloud computing. The Mauritius Software Craftsmanship Community is on the right way and this year's bootcamp on Windows Azure only marked the beginning of our journey. Thank you to our sponsors and my kudos to the MSPs! Update: Media coverage The event has been reported in local media, too. Following are some resources: Orange - Local - Business: Le cloud, pour des recherches approfondies sur le diabète Maurice Info.mu: Le cloud, pour des recherches approfondies sur le diabète Le Quotidien Pg 2: Global Windows Azure Bootcamp 2014 - Le cloud pour des recherches approfondies sur le diabète The Observer Pg 12: Le cloud, pour des recherches approfondies sur le diabète

  Read the article

• What is causing the unusual high load average?

  - by James

  I noticed on Tuesday night of last week, the load average went up sharply and it seemed abnormal since the traffic is small. Usually, the numbers usually average around .40 or lower and my server stuff (mysql, php and apache) are optimized. I noticed that the IOWait is unusually high even though the processes is barely using any CPU. top - 01:44:39 up 1 day, 21:13, 1 user, load average: 1.41, 1.09, 0.86 Tasks: 60 total, 1 running, 59 sleeping, 0 stopped, 0 zombie Cpu0 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 0.0%us, 0.3%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu4 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu5 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu6 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu7 : 0.0%us, 0.0%sy, 0.0%ni, 91.5%id, 8.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1048576k total, 331944k used, 716632k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1 root 15 0 2468 1376 1140 S 0 0.1 0:00.92 init 1656 root 15 0 13652 5212 664 S 0 0.5 0:00.00 apache2 9323 root 18 0 13652 5212 664 S 0 0.5 0:00.00 apache2 10079 root 18 0 3972 1248 972 S 0 0.1 0:00.00 su 10080 root 15 0 4612 1956 1448 S 0 0.2 0:00.01 bash 11298 root 15 0 13652 5212 664 S 0 0.5 0:00.00 apache2 11778 chikorit 15 0 2344 1092 884 S 0 0.1 0:00.05 top 15384 root 18 0 17544 13m 1568 S 0 1.3 0:02.28 miniserv.pl 15585 root 15 0 8280 2736 2168 S 0 0.3 0:00.02 sshd 15608 chikorit 15 0 8280 1436 860 S 0 0.1 0:00.02 sshd Here is the VMStat procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 1 0 0 768644 0 0 0 0 14 23 0 10 1 0 99 0 IOStat - Nothing unusal Total DISK READ: 67.13 K/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO COMMAND 19496 be/4 chikorit 11.85 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19501 be/4 mysql 3.95 K/s 0.00 B/s 0.00 % 0.00 % mysqld 19568 be/4 chikorit 11.85 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19569 be/4 chikorit 11.85 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19570 be/4 chikorit 11.85 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19571 be/4 chikorit 7.90 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19573 be/4 chikorit 7.90 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 1 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % init 11778 be/4 chikorit 0.00 B/s 0.00 B/s 0.00 % 0.00 % top 19470 be/4 mysql 0.00 B/s 0.00 B/s 0.00 % 0.00 % mysqld Load Average Chart - http://i.stack.imgur.com/kYsD0.png I want to be sure if this is not a MySQL problem before making sure. Also, this is a Ubuntu 10.04 LTS Server on OpenVZ. Edit: This will probably give a good picture on the IO Wait top - 22:12:22 up 17:41, 1 user, load average: 1.10, 1.09, 0.93 Tasks: 33 total, 1 running, 32 sleeping, 0 stopped, 0 zombie Cpu(s): 0.6%us, 0.2%sy, 0.0%ni, 89.0%id, 10.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1048576k total, 260708k used, 787868k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1 root 15 0 2468 1376 1140 S 0 0.1 0:00.88 init 5849 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 8063 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 9732 root 16 0 8280 2728 2168 S 0 0.3 0:00.02 sshd 9746 chikorit 18 0 8412 1444 864 S 0 0.1 0:01.10 sshd 9747 chikorit 18 0 4576 1960 1488 S 0 0.2 0:00.24 bash 13706 chikorit 15 0 2344 1088 884 R 0 0.1 0:00.03 top 15745 chikorit 15 0 12968 5108 1280 S 0 0.5 0:00.00 apache2 15751 chikorit 15 0 72184 25m 18m S 0 2.5 0:00.37 php5-fpm 15790 chikorit 18 0 12472 4640 1192 S 0 0.4 0:00.00 apache2 15797 chikorit 15 0 72888 23m 16m S 0 2.3 0:00.06 php5-fpm 16038 root 15 0 67772 2848 592 D 0 0.3 0:00.00 php5-fpm 16309 syslog 18 0 24084 1316 992 S 0 0.1 0:00.07 rsyslogd 16316 root 15 0 5472 908 500 S 0 0.1 0:00.00 sshd 16326 root 15 0 2304 908 712 S 0 0.1 0:00.02 cron 17464 root 15 0 10252 7560 856 D 0 0.7 0:01.88 psad 17466 root 18 0 1684 276 208 S 0 0.0 0:00.31 psadwatchd 17559 root 18 0 11444 2020 732 S 0 0.2 0:00.47 sendmail-mta 17688 root 15 0 10252 5388 1136 S 0 0.5 0:03.81 python 17752 teamspea 19 0 44648 7308 4676 S 0 0.7 1:09.70 ts3server_linux 18098 root 15 0 12336 6380 3032 S 0 0.6 0:00.47 apache2 18099 chikorit 18 0 10368 2536 464 S 0 0.2 0:00.00 apache2 18120 ntp 15 0 4336 1316 984 S 0 0.1 0:00.87 ntpd 18379 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 18387 mysql 15 0 62796 36m 5864 S 0 3.6 1:43.26 mysqld 19584 root 15 0 12336 4028 668 S 0 0.4 0:00.02 apache2 22498 root 16 0 12336 4028 668 S 0 0.4 0:00.00 apache2 24260 root 15 0 67772 3612 1356 S 0 0.3 0:00.22 php5-fpm 27712 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 27730 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 30343 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 30366 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 This is the free ram as of today. total used free shared buffers cached Mem: 1024 302 721 0 0 0 -/+ buffers/cache: 302 721 Swap: 0 0 0 Update: Looking into the logs, particularly the PHP5-FPM, which is causing the CPU spike. I found that its segment faulting for some apparent reason. [03-Jun-2012 06:11:20] NOTICE: [pool www] child 14132 started [03-Jun-2012 06:11:25] WARNING: [pool www] child 13664 exited on signal 11 (SIGSEGV) after 53.686322 seconds from start [03-Jun-2012 06:11:25] NOTICE: [pool www] child 14328 started [03-Jun-2012 06:11:25] WARNING: [pool www] child 14132 exited on signal 11 (SIGSEGV) after 4.708681 seconds from start [03-Jun-2012 06:11:25] NOTICE: [pool www] child 14329 started [03-Jun-2012 06:11:58] WARNING: [pool www] child 14328 exited on signal 11 (SIGSEGV) after 32.981228 seconds from start [03-Jun-2012 06:11:58] NOTICE: [pool www] child 15745 started [03-Jun-2012 06:12:25] WARNING: [pool www] child 15745 exited on signal 11 (SIGSEGV) after 27.442864 seconds from start [03-Jun-2012 06:12:25] NOTICE: [pool www] child 17446 started [03-Jun-2012 06:12:25] WARNING: [pool www] child 14329 exited on signal 11 (SIGSEGV) after 60.411278 seconds from start [03-Jun-2012 06:12:25] NOTICE: [pool www] child 17447 started [03-Jun-2012 06:13:02] WARNING: [pool www] child 17446 exited on signal 11 (SIGSEGV) after 36.746793 seconds from start [03-Jun-2012 06:13:02] NOTICE: [pool www] child 18133 started [03-Jun-2012 06:13:48] WARNING: [pool www] child 17447 exited on signal 11 (SIGSEGV) after 82.710107 seconds from start I'm thinking that this might be causing the problem. If that is the cause, probably switching it off that to fastcgi/fcgid might resolve it... but still, I want to see if something else might be causing it to do this.

  Read the article

• How to improve Varnish performance?

  - by Darkseal

  We're experiencing a strange problem with our current Varnish configuration. 4x Web Servers (IIS 6.5 on Windows 2003 Server, each installed on a Intel(R) Xeon(R) CPU E5450 @ 3.00GHz Quad Core, 4GB RAM) 3x Varnish Servers (varnish-3.0.3 revision 9e6a70f on Ubuntu 12.04.2 LTS - 64 bit/precise, Kernel Linux 3.2.0-29-generic, each installed on a Intel(R) Xeon(R) CPU E5450 @ 3.00GHz Quad Core, 4GB RAM) The Varnish Servers performance are awfully bad in general, to the point that if we shut down one of them the other two are unable to fullfill all the requests and start to skip beats resulting in pending requests, timeouts, 404, etc. What can we do to improve our Varnish performance? Considering that we're getting less than 5k request per seconds during our max peak, we should be able to serve our pages even with a single one of them without any problem. We use a standard, vanilla CFG, as shown by this varnishadm param.show output: acceptor_sleep_decay 0.900000 [] acceptor_sleep_incr 0.001000 [s] acceptor_sleep_max 0.050000 [s] auto_restart on [bool] ban_dups on [bool] ban_lurker_sleep 0.010000 [s] between_bytes_timeout 60.000000 [s] cc_command "exec gcc -std=gnu99 -g -O2 -pthread -fpic -shared - Wl,-x -o %o %s" cli_buffer 8192 [bytes] cli_timeout 20 [seconds] clock_skew 10 [s] connect_timeout 0.700000 [s] critbit_cooloff 180.000000 [s] default_grace 10.000000 [seconds] default_keep 0.000000 [seconds] default_ttl 120.000000 [seconds] diag_bitmap 0x0 [bitmap] esi_syntax 0 [bitmap] expiry_sleep 1.000000 [seconds] fetch_chunksize 128 [kilobytes] fetch_maxchunksize 262144 [kilobytes] first_byte_timeout 60.000000 [s] group varnish (113) gzip_level 6 [] gzip_memlevel 8 [] gzip_stack_buffer 32768 [Bytes] gzip_tmp_space 0 [] gzip_window 15 [] http_gzip_support off [bool] http_max_hdr 64 [header lines] http_range_support on [bool] http_req_hdr_len 8192 [bytes] http_req_size 32768 [bytes] http_resp_hdr_len 8192 [bytes] http_resp_size 32768 [bytes] idle_send_timeout 60 [seconds] listen_address :80 listen_depth 1024 [connections] log_hashstring on [bool] log_local_address off [bool] lru_interval 2 [seconds] max_esi_depth 5 [levels] max_restarts 4 [restarts] nuke_limit 50 [allocations] pcre_match_limit 10000 [] pcre_match_limit_recursion 10000 [] ping_interval 3 [seconds] pipe_timeout 60 [seconds] prefer_ipv6 off [bool] queue_max 100 [%] rush_exponent 3 [requests per request] saintmode_threshold 10 [objects] send_timeout 600 [seconds] sess_timeout 5 [seconds] sess_workspace 16384 [bytes] session_linger 50 [ms] session_max 100000 [sessions] shm_reclen 255 [bytes] shm_workspace 8192 [bytes] shortlived 10.000000 [s] syslog_cli_traffic on [bool] thread_pool_add_delay 2 [milliseconds] thread_pool_add_threshold 2 [requests] thread_pool_fail_delay 200 [milliseconds] thread_pool_max 2000 [threads] thread_pool_min 5 [threads] thread_pool_purge_delay 1000 [milliseconds] thread_pool_stack unlimited [bytes] thread_pool_timeout 300 [seconds] thread_pool_workspace 65536 [bytes] thread_pools 2 [pools] thread_stats_rate 10 [requests] user varnish (106) vcc_err_unref on [bool] vcl_dir /etc/varnish vcl_trace off [bool] vmod_dir /usr/lib/varnish/vmods waiter default (epoll, poll) This is our default.vcl file: LINK sub vcl_recv { # BASIC recv COMMANDS: # # lookup -> search the item in the cache # pass -> always serve a fresh item (no-caching) # pipe -> like pass but ensures a direct-connection with the backend (no-cache AND no-proxy) # Allow the backend to serve up stale content if it is responding slow. # This defines when Varnish should use a stale object if it has one in the cache. set req.grace = 30s; if (client.ip == "127.0.0.1") { # request from NGINX - do not alter X-Forwarded-For set req.http.HTTPS = "on"; } else { # Add an X-Forwarded-For to keep track of original request unset req.http.HTTPS; unset req.http.X-Forwarded-For; set req.http.X-Forwarded-For = client.ip; } set req.backend = www_director; # Strip all cookies to force an anonymous request when the back-end servers are down. if (!req.backend.healthy) { unset req.http.Cookie; } ## HHTP Accept-Encoding if (req.http.Accept-Encoding) { if (req.http.Accept-Encoding ~ "gzip") { set req.http.Accept-Encoding = "gzip"; } else if (req.http.Accept-Encoding ~ "deflate") { set req.http.Accept-Encoding = "deflate"; } else { unset req.http.Accept-Encoding; } } if (req.request != "GET" && req.request != "HEAD" && req.request != "PUT" && req.request != "POST" && req.request != "TRACE" && req.request != "OPTIONS" && req.request != "DELETE") { /* non-RFC2616 or CONNECT */ return (pipe); } if (req.request != "GET" && req.request != "HEAD") { /* only deal with GET and HEAD by default */ return (pass); } if (req.http.Authorization) { return (pass); } if (req.http.HTTPS ~ "on") { return (pass); } ###################################################### # COOKIE HANDLING ###################################################### # METHOD 1: do not remove cookies, but pass the page if they contain TB_NC if (!(req.url ~ "(?i)\.(png|gif|ipeg|jpg|ico|swf|css|js)(\?[a-z0-9]+)?$")) { if (req.http.Cookie && req.http.Cookie ~ "TB_NC") { return (pass); } } return (lookup); } # Code determining what to do when serving items from the IIS Server sub vcl_fetch { unset beresp.http.Server; set beresp.http.Server = "Server-1"; # Allow items to be stale if needed. This is the maximum time Varnish should keep an object. set beresp.grace = 1h; if (req.url ~ "(?i)\.(png|gif|ipeg|jpg|ico|swf|css|js)(\?[a-z0-9]+)?$") { unset beresp.http.set-cookie; } # Default Varnish VCL logic if (!beresp.cacheable || beresp.ttl <= 0s || beresp.http.Set-Cookie || beresp.http.Vary == "*") { set beresp.ttl = 120 s; return(hit_for_pass); } # Not Cacheable if it has specific TB_NC no-caching cookie if (req.http.Cookie && req.http.Cookie ~ "TB_NC") { set beresp.http.X-Cacheable = "NO:Got Cookie"; set beresp.ttl = 120 s; return(hit_for_pass); } # Not Cacheable if it has Cache-Control private else if (beresp.http.Cache-Control ~ "private") { set beresp.http.X-Cacheable = "NO:Cache-Control=private"; set beresp.ttl = 120 s; return(hit_for_pass); } # Not Cacheable if it has Cache-Control no-cache or Pragma no-cache else if (beresp.http.Cache-Control ~ "no-cache" || beresp.http.Pragma ~ "no-cache") { set beresp.http.X-Cacheable = "NO:Cache-Control=no-cache (or pragma no-cache)"; set beresp.ttl = 120 s; return(hit_for_pass); } # If we reach to this point, the object is cacheable. # Cacheable but with not enough ttl: we need to extend the lifetime of the object artificially # NOTE: Varnish default TTL is set in /etc/sysconfig/varnish # and can be checked using the following command: # varnishadm param.show default_ttl else if (beresp.ttl < 1s) { set beresp.ttl = 5s; set beresp.grace = 5s; set beresp.http.X-Cacheable = "YES:FORCED"; } # Cacheable and with valid TTL. else { set beresp.http.X-Cacheable = "YES"; } # DEBUG INFO (Cookies) # set beresp.http.X-Cookie-Debug = "Request cookie: " + req.http.Cookie; return(deliver); } sub vcl_error { set obj.http.Content-Type = "text/html; charset=utf-8"; if (obj.status == 404) { synthetic {" <!-- Markup for the 404 page goes here --> "}; } else if (obj.status == 500) { synthetic {" <!-- Markup for the 500 page goes here --> "}; } else if (obj.status == 503) { if (req.restarts < 4) { return(restart); } else { synthetic {" <!-- Markup for the 503 page goes here --> "}; } } else { synthetic {" <!-- Markup for a generic error page goes here --> "}; } } sub vcl_deliver { if (obj.hits > 0) { set resp.http.X-Cache = "HIT"; } else { set resp.http.X-Cache = "MISS"; } } Thanks in advance,

  Read the article

• Why ????? is displayed instead of non-english characters?

  - by smhnaji

  I first created a simple HTML page that uses UTF-8 as its character encoding. Then I moved the HTML content as a view in codeigniter and it was still ok (I had used non-english characters that were ok as always) I added a simple dynamic functionality (there is a contact us form in it that emails users feedback to site admin). Please note that the characters were ok at localhost (which is a LAMP server running on Ubuntu 12.04 LTS) Strange is that when I uploaded the app to server, all persian characters are shown as ???? (For example ??? (which means Name) is shown ??? and so so...) I have not even connected to mysql or any other DBMS. It's the only page in the website (it's more an under construction page) and nothing else has been used in it. Maybe I should state that I have also used session library to thank the user after his feedback was sent to admins, nothing else. I have really no idea about the problem. UPDATE Now I can see that the problem is only with cPanel. On Directadmin I can see that everything is normal. Both Chromium and Firefox DO use UTF-8 as page's character encoding. URL is http://WEBSITE.COM/dmf/dynamic/ (dmf is the abbreviation of the project name!). There is nothing non-english in the URL. The page's code is as follows: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml"> <head> <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> <title>??? ???????</title> <link rel="stylesheet" type="text/css" href="<?php echo base_url('template/css/style.css'); ?>" /> <!-- 1. jquery library --> <script src="http://ajax.googleapis.com/ajax/libs/jquery/1/jquery.min.js"> </script> <!-- 2. flowplayer --> <script src="http://releases.flowplayer.org/5.1.1/flowplayer.min.js"></script> <!-- 3. skin --> <link rel="stylesheet" type="text/css" href="http://releases.flowplayer.org/5.1.1/skin/minimalist.css" /> </head> <body> <div id="wrapper"> <header> <h1>??? ???????</h1> </header> <section id="box-container"> <?php echo form_open('contact', "id='contact-us'"); echo form_fieldset('???? ?? ??'); if ($this->session->userdata('mailsent')) { echo '<div>??????? ???? ??? ????? ??</div>'; $this->session->sess_destroy(); } echo '<input tabindex="1" id="name-in" value="???" type="text" name="name"/> <input tabindex="2" id="mail-in" value="?????" type="email" name="email"/> <textarea tabindex="3" id="content-in" name="message">???????</textarea> <input tabindex="4" id="submit" type="submit" value="?????" />'; echo '<div class="clear"></div>'; echo form_fieldset_close(); echo form_close(); ?> <div id="sms-comp"> <h2>?????? ??????</h2> <p> <span id="comp-title">?? ??? ????</span> ???? ??????? ???? ??? </p> </div> <div id="last-program"> <h2>?????? ????? ??????</h2> <div class="flowplayer"> <video id="my_video_1" width="212" height="126" poster="<?php echo base_url('template/images/img.jpg'); ?>" controls="controls" src="http://archive.org/download/Pbtestfilemp4videotestmp4/video_test.ogv" type='video/mp4'> </video> </div> </div> <div class="clear"></div> </section> </div> <footer> ????? ? ????? : <a href="http://powered-by.com/" target="_blank">????? ???</a> </footer> </body> </html>

  Read the article

• Linux C: "Interactive session" with separate read and write named pipes?

  - by ~sd-imi

  Hi all, I am trying to work with "Introduction to Interprocess Communication Using Named Pipes - Full-Duplex Communication Using Named Pipes", http://developers.sun.com/solaris/articles/named_pipes.html#5 ; in particular fd_server.c (included below for reference) Here is my info and compile line: :~$ cat /etc/issue Ubuntu 10.04 LTS \n \l :~$ gcc --version gcc (Ubuntu 4.4.3-4ubuntu5) 4.4.3 :~$ gcc fd_server.c -o fd_server fd_server.c creates two named pipes, one for reading and one for writing. What one can do, is: in one terminal, run the server and read (through cat) its write pipe: :~$ ./fd_server & 2/dev/null [1] 11354 :~$ cat /tmp/np2 and in another, write (using echo) to server's read pipe: :~$ echo "heeellloooo" /tmp/np1 going back to first terminal, one can see: :~$ cat /tmp/np2 HEEELLLOOOO 0[1]+ Exit 13 ./fd_server 2 /dev/null What I would like to do, is make sort of a "interactive" (or "shell"-like) session; that is, the server is run as usual, but instead of running "cat" and "echo", I'd like to use something akin to screen. What I mean by that, is that screen can be called like screen /dev/ttyS0 38400, and then it makes a sort of a interactive session, where what is typed in terminal is passed to /dev/ttyS0, and its response is written to terminal. Now, of course, I cannot use screen, because in my case the program has two separate nodes, and as far as I can tell, screen can refer to only one. How would one go about to achieve this sort of "interactive" session in this context (with two separate read/write pipes)? Thanks, Cheers! Code below: #include <stdio.h> #include <errno.h> #include <ctype.h> #include <sys/types.h> #include <sys/stat.h> #include <fcntl.h> //#include <fullduplex.h> /* For name of the named-pipe */ #define NP1 "/tmp/np1" #define NP2 "/tmp/np2" #define MAX_BUF_SIZE 255 #include <stdlib.h> //exit #include <string.h> //strlen int main(int argc, char *argv[]) { int rdfd, wrfd, ret_val, count, numread; char buf[MAX_BUF_SIZE]; /* Create the first named - pipe */ ret_val = mkfifo(NP1, 0666); if ((ret_val == -1) && (errno != EEXIST)) { perror("Error creating the named pipe"); exit (1); } ret_val = mkfifo(NP2, 0666); if ((ret_val == -1) && (errno != EEXIST)) { perror("Error creating the named pipe"); exit (1); } /* Open the first named pipe for reading */ rdfd = open(NP1, O_RDONLY); /* Open the second named pipe for writing */ wrfd = open(NP2, O_WRONLY); /* Read from the first pipe */ numread = read(rdfd, buf, MAX_BUF_SIZE); buf[numread] = '0'; fprintf(stderr, "Full Duplex Server : Read From the pipe : %sn", buf); /* Convert to the string to upper case */ count = 0; while (count < numread) { buf[count] = toupper(buf[count]); count++; } /* * Write the converted string back to the second * pipe */ write(wrfd, buf, strlen(buf)); } Edit: Right, just to clarify - it seems I found a document discussing something very similar, it is http://en.wikibooks.org/wiki/Serial_Programming/Serial_Linux#Configuration_with_stty - a modification of the script there ("For example, the following script configures the device and starts a background process for copying all received data from the serial device to standard output...") for the above program is below: # stty raw # ( ./fd_server 2>/dev/null; )& bgPidS=$! ( cat < /tmp/np2 ; )& bgPid=$! # Read commands from user, send them to device echo $(kill -0 $bgPidS 2>/dev/null ; echo $?) while [ "$(kill -0 $bgPidS 2>/dev/null ; echo $?)" -eq "0" ] && read cmd; do # redirect debug msgs to stderr, as here we're redirected to /tmp/np1 echo "$? - $bgPidS - $bgPid" >&2 echo "$cmd" echo -e "\nproc: $(kill -0 $bgPidS 2>/dev/null ; echo $?)" >&2 done >/tmp/np1 echo OUT # Terminate background read process - if they still exist if [ "$(kill -0 $bgPid 2>/dev/null ; echo $?)" -eq "0" ] ; then kill $bgPid fi if [ "$(kill -0 $bgPidS 2>/dev/null ; echo $?)" -eq "0" ] ; then kill $bgPidS fi # stty cooked So, saving the script as say starter.sh and calling it, results with the following session: $ ./starter.sh 0 i'm typing here and pressing [enter] at end 0 - 13496 - 13497 I'M TYPING HERE AND PRESSING [ENTER] AT END 0~?.N=?(?~? ?????}????@??????~? [garble] proc: 0 OUT which is what I'd call for "interactive session" (ignoring the debug statements) - server waits for me to enter a command; it gives its output after it receives a command (and as in this case it exits after first command, so does the starter script as well). Except that, I'd like to not have buffered input, but sent character by character (meaning the above session should exit after first key press, and print out a single letter only - which is what I expected stty raw would help with, but it doesn't: it just kills reaction to both Enter and Ctrl-C :) ) I was just wandering if there already is an existing command (akin to screen in respect to serial devices, I guess) that would accept two such named pipes as arguments, and establish a "terminal" or "shell" like session through them; or would I have to use scripts as above and/or program own 'client' that will behave as a terminal..

  Read the article

• E: Sub-process /usr/bin/dpkg returned an error code (1) seems to be choking on kde-runtime-data version issue

  - by BMT

  12.04 LTS, on a dell mini 10. Install stable until about a week ago. Updated about 1x a week, sometimes more often. Several days ago, I booted up and the system was no longer working correctly. All these symptoms occurred simultaneously: Cannot run (exit on opening, every time): Update manager, software center, ubuntuOne, libreOffice. Vinagre autostarts on boot, no explanation, not set to startup with Ubuntu. Using apt-get to fix install results in the following: maura@pandora:~$ sudo apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following package was automatically installed and is no longer required: libtelepathy-farstream2 Use 'apt-get autoremove' to remove them. The following extra packages will be installed: gwibber gwibber-service kde-runtime-data software-center Suggested packages: gwibber-service-flickr gwibber-service-digg gwibber-service-statusnet gwibber-service-foursquare gwibber-service-friendfeed gwibber-service-pingfm gwibber-service-qaiku unity-lens-gwibber The following packages will be upgraded: gwibber gwibber-service kde-runtime-data software-center 4 upgraded, 0 newly installed, 0 to remove and 39 not upgraded. 20 not fully installed or removed. Need to get 0 B/5,682 kB of archives. After this operation, 177 kB of additional disk space will be used. Do you want to continue [Y/n]? debconf: Perl may be unconfigured (Can't locate Scalar/Util.pm in @INC (@INC contains: /etc/perl /usr/local/lib/perl/5.14.2 /usr/local/share/perl/5.14.2 /usr/lib/perl5 /usr/share/perl5 /usr/lib/perl/5.14 /usr/share/perl/5.14 /usr/local/lib/site_perl .) at /usr/lib/perl/5.14/Hash/Util.pm line 9. BEGIN failed--compilation aborted at /usr/lib/perl/5.14/Hash/Util.pm line 9. Compilation failed in require at /usr/share/perl/5.14/fields.pm line 122. Compilation failed in require at /usr/share/perl5/Debconf/Log.pm line 10. Compilation failed in require at (eval 1) line 4. BEGIN failed--compilation aborted at (eval 1) line 4. ) -- aborting (Reading database ... 242672 files and directories currently installed.) Preparing to replace gwibber 3.4.1-0ubuntu1 (using .../gwibber_3.4.2-0ubuntu1_i386.deb) ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: warning: subprocess old pre-removal script returned error exit status 1 dpkg - trying script from the new package instead ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: error processing /var/cache/apt/archives/gwibber_3.4.2-0ubuntu1_i386.deb (--unpack): subprocess new pre-removal script returned error exit status 1 Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging dpkg: error while cleaning up: subprocess installed post-installation script returned error exit status 1 Preparing to replace gwibber-service 3.4.1-0ubuntu1 (using .../gwibber-service_3.4.2-0ubuntu1_all.deb) ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: warning: subprocess old pre-removal script returned error exit status 1 dpkg - trying script from the new package instead ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: error processing /var/cache/apt/archives/gwibber-service_3.4.2-0ubuntu1_all.deb (--unpack): subprocess new pre-removal script returned error exit status 1 Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging dpkg: error while cleaning up: subprocess installed post-installation script returned error exit status 1 Preparing to replace kde-runtime-data 4:4.8.3-0ubuntu0.1 (using .../kde-runtime-data_4%3a4.8.4-0ubuntu0.1_all.deb) ... Unpacking replacement kde-runtime-data ... dpkg: error processing /var/cache/apt/archives/kde-runtime-data_4%3a4.8.4-0ubuntu0.1_all.deb (--unpack): trying to overwrite '/usr/share/sounds', which is also in package sound-theme-freedesktop 0.7.pristine-2 dpkg-deb (subprocess): subprocess data was killed by signal (Broken pipe) dpkg-deb: error: subprocess <decompress> returned error exit status 2 Preparing to replace python-crypto 2.4.1-1 (using .../python-crypto_2.4.1-1_i386.deb) ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: warning: subprocess old pre-removal script returned error exit status 1 dpkg - trying script from the new package instead ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: error processing /var/cache/apt/archives/python-crypto_2.4.1-1_i386.deb (--unpack): subprocess new pre-removal script returned error exit status 1 No apport report written because MaxReports is reached already Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging dpkg: error while cleaning up: subprocess installed post-installation script returned error exit status 1 Preparing to replace software-center 5.2.2.2 (using .../software-center_5.2.4_all.deb) ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: warning: subprocess old pre-removal script returned error exit status 1 dpkg - trying script from the new package instead ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: error processing /var/cache/apt/archives/software-center_5.2.4_all.deb (--unpack): subprocess new pre-removal script returned error exit status 1 No apport report written because MaxReports is reached already Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging dpkg: error while cleaning up: subprocess installed post-installation script returned error exit status 1 Preparing to replace xdiagnose 2.5 (using .../archives/xdiagnose_2.5_all.deb) ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: warning: subprocess old pre-removal script returned error exit status 1 dpkg - trying script from the new package instead ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: error processing /var/cache/apt/archives/xdiagnose_2.5_all.deb (--unpack): subprocess new pre-removal script returned error exit status 1 No apport report written because MaxReports is reached already Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging dpkg: error while cleaning up: subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/gwibber_3.4.2-0ubuntu1_i386.deb /var/cache/apt/archives/gwibber-service_3.4.2-0ubuntu1_all.deb /var/cache/apt/archives/kde-runtime-data_4%3a4.8.4-0ubuntu0.1_all.deb /var/cache/apt/archives/python-crypto_2.4.1-1_i386.deb /var/cache/apt/archives/software-center_5.2.4_all.deb /var/cache/apt/archives/xdiagnose_2.5_all.deb E: Sub-process /usr/bin/dpkg returned an error code (1) maura@pandora:~$ ^C maura@pandora:~$

  Read the article

• Installed Ubuntu 14.04LTS

  - by user291729

  On my laptop which came pre-installed with Windows 8.1. Felt I needed to see the competition for myself to establish which was a better OS. So I followed the channels to dual boot. All seemed fine and I accessed Ubuntu with no issues after selecting this from the menu to select the OS. I should add that the boot method was changed to legacy. However, since using Ubuntu, I no longer have the ability to select the OS. The laptop simply logs straight into Ubuntu. I therefore attempted to access the recovery options, only it appears the Windows 8 bootloader has somehow been corrupted as I am now told to use the Windows 8 recovery disc (which, as this was pre-installed - I do not have). Left with no other alternative, I have scoured these forums without success, and so I am hoping someone in the know (or who has experienced similar) can help. I have tried boot repair again without success. On rebooting I am only presented with a basic splash screen asking me to select Ubuntu, Memtest, Windows 8 Recovery or Windows 8 Bootloader (The bootloaders again require I insert the disc). I have tried Code: cat /boot/grub/grub.cfg df -h sudo fdisk -l cat /proc/partitions # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi if [ "${next_entry}" ] ; then set default="${next_entry}" set next_entry= save_env next_entry set boot_once=true else set default="0" fi if [ x"${feature_menuentry_id}" = xy ]; then menuentry_id_option="--id" else menuentry_id_option="" fi export menuentry_id_option if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { if [ x$feature_all_video_module = xy ]; then insmod all_video else insmod efi_gop insmod efi_uga insmod ieee1275_fb insmod vbe insmod vga insmod video_bochs insmod video_cirrus fi } if [ x$feature_default_font_path = xy ] ; then font=unicode else insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi font="/usr/share/grub/unicode.pf2" fi if loadfont $font ; then set gfxmode=800x600 load_video insmod gfxterm set locale_dir=$prefix/locale set lang=en_GB insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ] ; then set timeout=-1 else if [ x$feature_timeout_style = xy ] ; then set timeout_style=menu set timeout=20 # Fallback normal timeout code in case the timeout_style feature is # unavailable. else set timeout=20 fi fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="${1}" if [ "${1}" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ "${recordfail}" != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode menuentry 'Ubuntu' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-simple-d2f10f36-e3bb-4d83-a9b8-5d456fc454ad' { recordfail load_video gfxmode $linux_gfx_mode insmod gzio insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi linux /boot/vmlinuz-3.13.0-29-generic root=UUID=d2f10f36-e3bb-4d83-a9b8-5d456fc454ad ro vga=789 quiet quiet splash $vt_handoff initrd /boot/initrd.img-3.13.0-29-generic } submenu 'Advanced options for Ubuntu' $menuentry_id_option 'gnulinux-advanced-d2f10f36-e3bb-4d83-a9b8-5d456fc454ad' { menuentry 'Ubuntu, with Linux 3.13.0-29-generic' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.13.0-29-generic-advanced-d2f10f36-e3bb-4d83-a9b8-5d456fc454ad' { recordfail load_video gfxmode $linux_gfx_mode insmod gzio insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi echo 'Loading Linux 3.13.0-29-generic ...' linux /boot/vmlinuz-3.13.0-29-generic root=UUID=d2f10f36-e3bb-4d83-a9b8-5d456fc454ad ro vga=789 quiet quiet splash $vt_handoff echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.13.0-29-generic } menuentry 'Ubuntu, with Linux 3.13.0-29-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.13.0-29-generic-recovery-d2f10f36-e3bb-4d83-a9b8-5d456fc454ad' { recordfail load_video insmod gzio insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi echo 'Loading Linux 3.13.0-29-generic ...' linux /boot/vmlinuz-3.13.0-29-generic root=UUID=d2f10f36-e3bb-4d83-a9b8-5d456fc454ad ro recovery nomodeset vga=789 quiet echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.13.0-29-generic } menuentry 'Ubuntu, with Linux 3.13.0-24-generic' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.13.0-24-generic-advanced-d2f10f36-e3bb-4d83-a9b8-5d456fc454ad' { recordfail load_video gfxmode $linux_gfx_mode insmod gzio insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi echo 'Loading Linux 3.13.0-24-generic ...' linux /boot/vmlinuz-3.13.0-24-generic root=UUID=d2f10f36-e3bb-4d83-a9b8-5d456fc454ad ro vga=789 quiet quiet splash $vt_handoff echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.13.0-24-generic } menuentry 'Ubuntu, with Linux 3.13.0-24-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.13.0-24-generic-recovery-d2f10f36-e3bb-4d83-a9b8-5d456fc454ad' { recordfail load_video insmod gzio insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi echo 'Loading Linux 3.13.0-24-generic ...' linux /boot/vmlinuz-3.13.0-24-generic root=UUID=d2f10f36-e3bb-4d83-a9b8-5d456fc454ad ro recovery nomodeset vga=789 quiet echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.13.0-24-generic } } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry 'Memory test (memtest86+)' { insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi knetbsd /boot/memtest86+.elf } menuentry 'Memory test (memtest86+, serial console 115200)' { insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry 'Windows Recovery Environment (loader) (on /dev/sda2)' --class windows --class os $menuentry_id_option 'osprober-chain-7A6A69D66A698FA5' { insmod part_gpt insmod ntfs set root='hd0,gpt2' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt2 --hint-efi=hd0,gpt2 --hint-baremetal=ahci0,gpt2 7A6A69D66A698FA5 else search --no-floppy --fs-uuid --set=root 7A6A69D66A698FA5 fi drivemap -s (hd0) ${root} chainloader +1 } menuentry 'Windows 8 (loader) (on /dev/sda3)' --class windows --class os $menuentry_id_option 'osprober-chain-8C88-80F7' { insmod part_gpt insmod fat set root='hd0,gpt3' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt3 --hint-efi=hd0,gpt3 --hint-baremetal=ahci0,gpt3 8C88-80F7 else search --no-floppy --fs-uuid --set=root 8C88-80F7 fi drivemap -s (hd0) ${root} chainloader +1 } set timeout_style=menu if [ "${timeout}" = 0 ]; then set timeout=10 fi ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/30_uefi-firmware ### ### END /etc/grub.d/30_uefi-firmware ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f ${config_directory}/custom.cfg ]; then source ${config_directory}/custom.cfg elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi if [ "${next_entry}" ] ; then set default="${next_entry}" set next_entry= save_env next_entry set boot_once=true else set default="0" fi if [ x"${feature_menuentry_id}" = xy ]; then menuentry_id_option="--id" else menuentry_id_option="" fi export menuentry_id_option if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { if [ x$feature_all_video_module = xy ]; then insmod all_video else insmod efi_gop insmod efi_uga insmod ieee1275_fb insmod vbe insmod vga insmod video_bochs insmod video_cirrus fi } if [ x$feature_default_font_path = xy ] ; then font=unicode else insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi font="/usr/share/grub/unicode.pf2" fi if loadfont $font ; then set gfxmode=800x600 load_video insmod gfxterm set locale_dir=$prefix/locale set lang=en_GB insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ] ; then set timeout=-1 else if [ x$feature_timeout_style = xy ] ; then set timeout_style=menu set timeout=20 # Fallback normal timeout code in case the timeout_style feature is # unavailable. else set timeout=20 fi fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="${1}" if [ "${1}" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ "${recordfail}" != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode menuentry 'Ubuntu' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-simple-d2f10f36-e3bb-4d83-a9b8-5d456fc454ad' { recordfail load_video gfxmode $linux_gfx_mode insmod gzio insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi linux /boot/vmlinuz-3.13.0-29-generic root=UUID=d2f10f36-e3bb-4d83-a9b8-5d456fc454ad ro vga=789 quiet quiet splash $vt_handoff initrd /boot/initrd.img-3.13.0-29-generic } submenu 'Advanced options for Ubuntu' $menuentry_id_option 'gnulinux-advanced-d2f10f36-e3bb-4d83-a9b8-5d456fc454ad' { menuentry 'Ubuntu, with Linux 3.13.0-29-generic' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.13.0-29-generic-advanced-d2f10f36-e3bb-4d83-a9b8-5d456fc454ad' { recordfail load_video gfxmode $linux_gfx_mode insmod gzio insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi echo 'Loading Linux 3.13.0-29-generic ...' linux /boot/vmlinuz-3.13.0-29-generic root=UUID=d2f10f36-e3bb-4d83-a9b8-5d456fc454ad ro vga=789 quiet quiet splash $vt_handoff echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.13.0-29-generic } menuentry 'Ubuntu, with Linux 3.13.0-29-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.13.0-29-generic-recovery-d2f10f36-e3bb-4d83-a9b8-5d456fc454ad' { recordfail load_video insmod gzio insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi echo 'Loading Linux 3.13.0-29-generic ...' linux /boot/vmlinuz-3.13.0-29-generic root=UUID=d2f10f36-e3bb-4d83-a9b8-5d456fc454ad ro recovery nomodeset vga=789 quiet echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.13.0-29-generic } menuentry 'Ubuntu, with Linux 3.13.0-24-generic' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.13.0-24-generic-advanced-d2f10f36-e3bb-4d83-a9b8-5d456fc454ad' { recordfail load_video gfxmode $linux_gfx_mode insmod gzio insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi echo 'Loading Linux 3.13.0-24-generic ...' linux /boot/vmlinuz-3.13.0-24-generic root=UUID=d2f10f36-e3bb-4d83-a9b8-5d456fc454ad ro vga=789 quiet quiet splash $vt_handoff echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.13.0-24-generic } menuentry 'Ubuntu, with Linux 3.13.0-24-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.13.0-24-generic-recovery-d2f10f36-e3bb-4d83-a9b8-5d456fc454ad' { recordfail load_video insmod gzio insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi echo 'Loading Linux 3.13.0-24-generic ...' linux /boot/vmlinuz-3.13.0-24-generic root=UUID=d2f10f36-e3bb-4d83-a9b8-5d456fc454ad ro recovery nomodeset vga=789 quiet echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.13.0-24-generic } } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry 'Memory test (memtest86+)' { insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi knetbsd /boot/memtest86+.elf } menuentry 'Memory test (memtest86+, serial console 115200)' { insmod part_gpt insmod ext2 set root='hd0,gpt9' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 d2f10f36-e3bb-4d83-a9b8-5d456fc454ad else search --no-floppy --fs-uuid --set=root d2f10f36-e3bb-4d83-a9b8-5d456fc454ad fi linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry 'Windows Recovery Environment (loader) (on /dev/sda2)' --class windows --class os $menuentry_id_option 'osprober-chain-7A6A69D66A698FA5' { insmod part_gpt insmod ntfs set root='hd0,gpt2' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt2 --hint-efi=hd0,gpt2 --hint-baremetal=ahci0,gpt2 7A6A69D66A698FA5 else search --no-floppy --fs-uuid --set=root 7A6A69D66A698FA5 fi drivemap -s (hd0) ${root} chainloader +1 } menuentry 'Windows 8 (loader) (on /dev/sda3)' --class windows --class os $menuentry_id_option 'osprober-chain-8C88-80F7' { insmod part_gpt insmod fat set root='hd0,gpt3' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt3 --hint-efi=hd0,gpt3 --hint-baremetal=ahci0,gpt3 8C88-80F7 else search --no-floppy --fs-uuid --set=root 8C88-80F7 fi drivemap -s (hd0) ${root} chainloader +1 } set timeout_style=menu if [ "${timeout}" = 0 ]; then set timeout=10 fi ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/30_uefi-firmware ### ### END /etc/grub.d/30_uefi-firmware ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f ${config_directory}/custom.cfg ]; then source ${config_directory}/custom.cfg elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### john@john-SVE1713Y1EB:~$ ^C john@john-SVE1713Y1EB:~$ ^C john@john-SVE1713Y1EB:~$ df -h Filesystem Size Used Avail Use% Mounted on /dev/sda9 84G 7.1G 73G 9% / none 4.0K 0 4.0K 0% /sys/fs/cgroup udev 3.9G 4.0K 3.9G 1% /dev tmpfs 794M 1.4M 793M 1% /run none 5.0M 0 5.0M 0% /run/lock none 3.9G 80K 3.9G 1% /run/shm none 100M 52K 100M 1% /run/user /dev/sdc1 7.5G 2.2G 5.4G 29% /media/john/DYLANMUSIC /dev/sr0 964M 964M 0 100% /media/john/Ubuntu 14.04 LTS amd64 /dev/sdb1 1.9T 892G 972G 48% /media/john/Storage Main WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x4e2ccf75 Device Boot Start End Blocks Id System /dev/sda1 1 1953525167 976762583+ ee GPT Partition 1 does not start on physical sector boundary. Disk /dev/sdc: 8011 MB, 8011120640 bytes 41 heads, 41 sectors/track, 9307 cylinders, total 15646720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdc1 8064 15646719 7819328 b W95 FAT32 Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc7d968ff Device Boot Start End Blocks Id System /dev/sdb1 64 3907029119 1953514528 7 HPFS/NTFS/exFAT major minor #blocks name 8 0 976762584 sda 8 1 266240 sda1 8 2 1509376 sda2 8 3 266240 sda3 8 4 131072 sda4 8 5 841012780 sda5 8 6 358400 sda6 8 7 35376128 sda7 8 8 1024 sda8 8 9 89501696 sda9 8 10 8337408 sda10 11 0 987136 sr0 8 32 7823360 sdc 8 33 7819328 sdc1 8 16 1953514584 sdb 8 17 1953514528 sdb1 I am no expert on this and I'm at a loss as how to correct this without having to re-format everything and reinstall Windows 8. However, if I'm to try using Ubuntu again then there is the risk this problem may come back. Again, I did not do anything manually - the installer did everything (with the exception of changing the boot to Legacy to allow the booting of another bootloader). LiveCD works but doesn't give me the options that I've seen here and as mentioned earlier, only boot recovery only gives me the options as mentioned earlier. Also this fails to load via USB (possibly because HDD comes before USB in the boot order?). Being used to a Windows environment, the Ubuntu (and Linux) environment is a dive at a less than comfortable depth at present (but one I fully intend to get to grips with - especially the commands being more common via Terminal). I very much appreciate the help with this guys.

  Read the article

• Bitnami redmine error SVN

  - by Evgeniy

  I'm installing the Bitnami Redmine stack (redmine + subversion). Firstly I install configure and test it locally (Ubuntu 14.04 LTS). And everything is OK. I install Bitnami stack on server (Red Hat 4.4.7-4) and configure SVN. I commit files into SVN and connect project into Redmine with SVN repository, but when I try see it Rredmine displays 404 error. In the Redmine log file I see the following errors: Started GET "/redmine/projects/web-user-panel/repository" for 127.0.0.1 at 2014-04-24 11:34:20 +0300 Processing by RepositoriesController#show as HTML Parameters: {"id"=>"web-user-panel"} Current user: user (id=13) Error parsing svn output: #<REXML::ParseException: No close tag for /lists/list> /var/www/html/redmine/ruby/lib/ruby/1.9.1/rexml/parsers/treeparser.rb:28:in `parse' /var/www/html/redmine/ruby/lib/ruby/1.9.1/rexml/document.rb:245:in `build' /var/www/html/redmine/ruby/lib/ruby/1.9.1/rexml/document.rb:43:in `initialize' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/xml_mini/rexml.rb:30:in `new' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/xml_mini/rexml.rb:30:in `parse' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/xml_mini.rb:80:in `parse' /var/www/html/redmine/apps/redmine/htdocs/lib/redmine/scm/adapters/abstract_adapter.rb:313:in `parse_xml' /var/www/html/redmine/apps/redmine/htdocs/lib/redmine/scm/adapters/subversion_adapter.rb:106:in `block in entries' /var/www/html/redmine/apps/redmine/htdocs/lib/redmine/scm/adapters/abstract_adapter.rb:258:in `call' /var/www/html/redmine/apps/redmine/htdocs/lib/redmine/scm/adapters/abstract_adapter.rb:258:in `block in shellout' /var/www/html/redmine/apps/redmine/htdocs/lib/redmine/scm/adapters/abstract_adapter.rb:255:in `popen' /var/www/html/redmine/apps/redmine/htdocs/lib/redmine/scm/adapters/abstract_adapter.rb:255:in `shellout' /var/www/html/redmine/apps/redmine/htdocs/lib/redmine/scm/adapters/abstract_adapter.rb:212:in `shellout' /var/www/html/redmine/apps/redmine/htdocs/lib/redmine/scm/adapters/subversion_adapter.rb:100:in `entries' /var/www/html/redmine/apps/redmine/htdocs/app/models/repository.rb:198:in `scm_entries' /var/www/html/redmine/apps/redmine/htdocs/app/models/repository.rb:203:in `entries' /var/www/html/redmine/apps/redmine/htdocs/app/controllers/repositories_controller.rb:116:in `show' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_controller/metal/implicit_render.rb:4:in `send_action' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/abstract_controller/base.rb:167:in `process_action' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_controller/metal/rendering.rb:10:in `process_action' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/abstract_controller/callbacks.rb:18:in `block in process_action' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/callbacks.rb:491:in `_run__2883861927089110970__process_action__2542827355008294621__callbacks' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/callbacks.rb:405:in `__run_callback' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/callbacks.rb:385:in `_run_process_action_callbacks' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/callbacks.rb:81:in `run_callbacks' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/abstract_controller/callbacks.rb:17:in `process_action' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_controller/metal/rescue.rb:29:in `process_action' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_controller/metal/instrumentation.rb:30:in `block in process_action' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/notifications.rb:123:in `block in instrument' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/notifications/instrumenter.rb:20:in `instrument' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/notifications.rb:123:in `instrument' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_controller/metal/instrumentation.rb:29:in `process_action' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_controller/metal/params_wrapper.rb:207:in `process_action' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activerecord-3.2.17/lib/active_record/railties/controller_runtime.rb:18:in `process_action' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/abstract_controller/base.rb:121:in `process' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/abstract_controller/rendering.rb:45:in `process' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_controller/metal.rb:203:in `dispatch' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_controller/metal/rack_delegation.rb:14:in `dispatch' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_controller/metal.rb:246:in `block in action' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/routing/route_set.rb:73:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/routing/route_set.rb:73:in `dispatch' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/routing/route_set.rb:36:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/journey-1.0.4/lib/journey/router.rb:68:in `block in call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/journey-1.0.4/lib/journey/router.rb:56:in `each' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/journey-1.0.4/lib/journey/router.rb:56:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/routing/route_set.rb:608:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-openid-1.3.1/lib/rack/openid.rb:98:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/middleware/best_standards_support.rb:17:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-1.4.5/lib/rack/etag.rb:23:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-1.4.5/lib/rack/conditionalget.rb:25:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/middleware/head.rb:14:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/middleware/params_parser.rb:21:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/middleware/flash.rb:242:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-1.4.5/lib/rack/session/abstract/id.rb:210:in `context' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-1.4.5/lib/rack/session/abstract/id.rb:205:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/middleware/cookies.rb:341:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activerecord-3.2.17/lib/active_record/query_cache.rb:64:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activerecord-3.2.17/lib/active_record/connection_adapters/abstract/connection_pool.rb:479:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/middleware/callbacks.rb:28:in `block in call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/callbacks.rb:405:in `_run__1805290955544829105__call__1486932417638469082__callbacks' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/callbacks.rb:405:in `__run_callback' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/callbacks.rb:385:in `_run_call_callbacks' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/callbacks.rb:81:in `run_callbacks' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/middleware/callbacks.rb:27:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/middleware/remote_ip.rb:31:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/middleware/debug_exceptions.rb:16:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/middleware/show_exceptions.rb:56:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/railties-3.2.17/lib/rails/rack/logger.rb:32:in `call_app' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/railties-3.2.17/lib/rails/rack/logger.rb:16:in `block in call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/tagged_logging.rb:22:in `tagged' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/railties-3.2.17/lib/rails/rack/logger.rb:16:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/middleware/request_id.rb:22:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-1.4.5/lib/rack/methodoverride.rb:21:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-1.4.5/lib/rack/runtime.rb:17:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/activesupport-3.2.17/lib/active_support/cache/strategy/local_cache.rb:72:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-1.4.5/lib/rack/lock.rb:15:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/actionpack-3.2.17/lib/action_dispatch/middleware/static.rb:63:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-cache-1.2/lib/rack/cache/context.rb:136:in `forward' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-cache-1.2/lib/rack/cache/context.rb:245:in `fetch' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-cache-1.2/lib/rack/cache/context.rb:185:in `lookup' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-cache-1.2/lib/rack/cache/context.rb:66:in `call!' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-cache-1.2/lib/rack/cache/context.rb:51:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/railties-3.2.17/lib/rails/engine.rb:484:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/railties-3.2.17/lib/rails/application.rb:231:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/railties-3.2.17/lib/rails/railtie/configurable.rb:30:in `method_missing' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-1.4.5/lib/rack/builder.rb:134:in `call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-1.4.5/lib/rack/urlmap.rb:64:in `block in call' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-1.4.5/lib/rack/urlmap.rb:49:in `each' /var/www/html/redmine/apps/redmine/htdocs/vendor/bundle/ruby/1.9.1/gems/rack-1.4.5/lib/rack/urlmap.rb:49:in `call' /var/www/html/redmine/ruby/lib/ruby/gems/1.9.1/gems/passenger-4.0.40/lib/phusion_passenger/rack/thread_handler_extension.rb:74:in `process_request' /var/www/html/redmine/ruby/lib/ruby/gems/1.9.1/gems/passenger-4.0.40/lib/phusion_passenger/request_handler/thread_handler.rb:141:in `accept_and_process_next_request' /var/www/html/redmine/ruby/lib/ruby/gems/1.9.1/gems/passenger-4.0.40/lib/phusion_passenger/request_handler/thread_handler.rb:109:in `main_loop' /var/www/html/redmine/ruby/lib/ruby/gems/1.9.1/gems/passenger-4.0.40/lib/phusion_passenger/request_handler.rb:448:in `block (3 levels) in start_threads' ... No close tag for /lists/list Line: 4 Position: 93 Last 80 unconsumed characters: Output was: <?xml version="1.0" encoding="UTF-8"?> <lists> <list path="svn://127.0.0.1/voxysuser"> Rendered common/error.html.erb within layouts/base (0.1ms) Completed 404 Not Found in 69.1ms (Views: 15.1ms | ActiveRecord: 3.0ms) How can I resolve this problem? I googled it, but similar problem fixed should be fixed 3 years ago. I'm installing the latest Bitnami Redmine 2.5.1-1 stack. UPDATE Well, I found next way. If I use the http protocol it works fine, but I should remove access for svn by web. That's why I create virtual host on localhost and get info from svn use 127.0.0.1 IP. <VirtualHost 127.0.0.1:8000> <Location /repo> DAV svn SVNPath "PATH_TO_MY_REPOSITORY" </Location> And this it work good.

  Read the article

• TCP RST right after FIN/ACK

  - by Nitzan Shaked

  I am having the weirdest issue: I have a web server which sometimes, only on very specific requests, will send a RST to the client after having sent the FIN datagram. First, a description of the setup: The server runs on an Ubuntu 12.04.1 LTS, which itself is a VM guest inside a Win7 x64 host, in bridged mode. ufw is disabled on the host The client runs on a iOS simulator, which runs on OS X Mountain Lion, which is a VM guest (hackintosh) inside a Win7 x64 host, in bridged mode. Both client and server are on the same LAN, one is connected to the home router via an Ethernet cable, and then other thru WiFi. I happened to glimpse over the server's http logs and found that the client sometimes issuing multiple subsequent identical requests. Further investigation led me to discover that this happens when the server sends a RST, and that the client is simply re-trying. I am attaching several tcpdump's: Good1 is the server-side tcpdump of a good session ("good" meaning no RST was generated). Good3 is another sever-side tcpdump of a good session. (The difference between Good1 and Good3 is the order in which ACK's were sent from the server to the client, ACK'ing the client's request. The client's request arives in 2 segements (specifically: one for the http headers, and another for a body containing an empty json object, "{}"). In Good1, the server ACK's both request segments, using 2 ACK segments, after the second request has arrived. In Good3, the server ACK's each request segment with an ACK segment as soon as the request segment arrives. Not that it should make a difference.) Bad1 is a dump, both client- and server-side, of a bad session. Bad2 is another bad session, this time server-side only. Note that in all "bad" sessions, the server ACK's each request segments immediately after having received it. I've looked at a few other bad sessions, and the situation is the same in all of them. But this is also the behavior in "Good3", so I don't see how that observation helps me, of for that matter why it should matter. I can't find any difference between good and bad sessions, or at least one that I think should matter. My question is: why are those RST's being generated? Or at least: how do I go about debugging this, or providing more info here that'll help? Edit 2 new facts that I have learned: Section 4.2.2.13 of the RFC (1122) (and Wikipedia, in the article "TCP", under "Connection Termination") says that a TCP application on one host may close the connection before it has read all of the data in its socket buffer, and in such a case the TCP on the host will sent a RST to the other side, to let it know that not all the data it has sent has been read. I'm not sure I completely understand this, since closing my side of the connection still allows me to read, no? It also means that I can't write any more. I am not sure this is relevant, though, since I see a RST after FIN. There are multiple complaints of this happening with wsgiref (Python's dev-mode HTTP server), which is exactly what I'm using. I'll keep updating as I find out more. Thanks! ~~~~~~~~~~~~~~~~~~~~ Good1 -- Server Side ~~~~~~~~~~~~~~~~~~~~ 13:28:02.308319 IP 192.168.1.51.51479 > 192.168.1.132.5000: Flags [S], seq 94268074, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 943308864 ecr 0,sackOK,eol], length 0 13:28:02.308336 IP 192.168.1.132.5000 > 192.168.1.51.51479: Flags [S.], seq 1726304574, ack 94268075, win 14480, options [mss 1460,sackOK,TS val 326480982 ecr 943308864,nop,wscale 3], length 0 13:28:02.309750 IP 192.168.1.51.51479 > 192.168.1.132.5000: Flags [.], ack 1, win 8235, options [nop,nop,TS val 943308865 ecr 326480982], length 0 13:28:02.310744 IP 192.168.1.51.51479 > 192.168.1.132.5000: Flags [P.], seq 1:351, ack 1, win 8235, options [nop,nop,TS val 943308865 ecr 326480982], length 350 13:28:02.310766 IP 192.168.1.51.51479 > 192.168.1.132.5000: Flags [P.], seq 351:353, ack 1, win 8235, options [nop,nop,TS val 943308865 ecr 326480982], length 2 13:28:02.310841 IP 192.168.1.132.5000 > 192.168.1.51.51479: Flags [.], ack 351, win 1944, options [nop,nop,TS val 326480983 ecr 943308865], length 0 13:28:02.310918 IP 192.168.1.132.5000 > 192.168.1.51.51479: Flags [.], ack 353, win 1944, options [nop,nop,TS val 326480983 ecr 943308865], length 0 13:28:02.315931 IP 192.168.1.132.5000 > 192.168.1.51.51479: Flags [P.], seq 1:18, ack 353, win 1944, options [nop,nop,TS val 326480984 ecr 943308865], length 17 13:28:02.316107 IP 192.168.1.132.5000 > 192.168.1.51.51479: Flags [FP.], seq 18:684, ack 353, win 1944, options [nop,nop,TS val 326480984 ecr 943308865], length 666 13:28:02.317651 IP 192.168.1.51.51479 > 192.168.1.132.5000: Flags [.], ack 18, win 8234, options [nop,nop,TS val 943308872 ecr 326480984], length 0 13:28:02.318288 IP 192.168.1.51.51479 > 192.168.1.132.5000: Flags [.], ack 685, win 8192, options [nop,nop,TS val 943308872 ecr 326480984], length 0 13:28:02.318640 IP 192.168.1.51.51479 > 192.168.1.132.5000: Flags [F.], seq 353, ack 685, win 8192, options [nop,nop,TS val 943308872 ecr 326480984], length 0 13:28:02.318651 IP 192.168.1.132.5000 > 192.168.1.51.51479: Flags [.], ack 354, win 1944, options [nop,nop,TS val 326480985 ecr 943308872], length 0 ~~~~~~~~~~~~~~~~~~~~ Good3 -- Server Side ~~~~~~~~~~~~~~~~~~~~ 13:28:03.311143 IP 192.168.1.51.51486 > 192.168.1.132.5000: Flags [S], seq 1982901126, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 943309853 ecr 0,sackOK,eol], length 0 13:28:03.311155 IP 192.168.1.132.5000 > 192.168.1.51.51486: Flags [S.], seq 2245063571, ack 1982901127, win 14480, options [mss 1460,sackOK,TS val 326481233 ecr 943309853,nop,wscale 3], length 0 13:28:03.312671 IP 192.168.1.51.51486 > 192.168.1.132.5000: Flags [.], ack 1, win 8235, options [nop,nop,TS val 943309854 ecr 326481233], length 0 13:28:03.313330 IP 192.168.1.51.51486 > 192.168.1.132.5000: Flags [P.], seq 1:351, ack 1, win 8235, options [nop,nop,TS val 943309855 ecr 326481233], length 350 13:28:03.313337 IP 192.168.1.132.5000 > 192.168.1.51.51486: Flags [.], ack 351, win 1944, options [nop,nop,TS val 326481234 ecr 943309855], length 0 13:28:03.313342 IP 192.168.1.51.51486 > 192.168.1.132.5000: Flags [P.], seq 351:353, ack 1, win 8235, options [nop,nop,TS val 943309855 ecr 326481233], length 2 13:28:03.313346 IP 192.168.1.132.5000 > 192.168.1.51.51486: Flags [.], ack 353, win 1944, options [nop,nop,TS val 326481234 ecr 943309855], length 0 13:28:03.327942 IP 192.168.1.132.5000 > 192.168.1.51.51486: Flags [P.], seq 1:18, ack 353, win 1944, options [nop,nop,TS val 326481237 ecr 943309855], length 17 13:28:03.328253 IP 192.168.1.132.5000 > 192.168.1.51.51486: Flags [FP.], seq 18:684, ack 353, win 1944, options [nop,nop,TS val 326481237 ecr 943309855], length 666 13:28:03.329076 IP 192.168.1.51.51486 > 192.168.1.132.5000: Flags [.], ack 18, win 8234, options [nop,nop,TS val 943309868 ecr 326481237], length 0 13:28:03.329688 IP 192.168.1.51.51486 > 192.168.1.132.5000: Flags [.], ack 685, win 8192, options [nop,nop,TS val 943309868 ecr 326481237], length 0 13:28:03.330361 IP 192.168.1.51.51486 > 192.168.1.132.5000: Flags [F.], seq 353, ack 685, win 8192, options [nop,nop,TS val 943309869 ecr 326481237], length 0 13:28:03.330370 IP 192.168.1.132.5000 > 192.168.1.51.51486: Flags [.], ack 354, win 1944, options [nop,nop,TS val 326481238 ecr 943309869], length 0 ~~~~~~~~~~~~~~~~~~~~ Bad1 -- Server Side ~~~~~~~~~~~~~~~~~~~~ 13:28:01.311876 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [S], seq 920400580, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 943307883 ecr 0,sackOK,eol], length 0 13:28:01.311896 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [S.], seq 3103085782, ack 920400581, win 14480, options [mss 1460,sackOK,TS val 326480733 ecr 943307883,nop,wscale 3], length 0 13:28:01.313509 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [.], ack 1, win 8235, options [nop,nop,TS val 943307884 ecr 326480733], length 0 13:28:01.315614 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [P.], seq 1:351, ack 1, win 8235, options [nop,nop,TS val 943307886 ecr 326480733], length 350 13:28:01.315727 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [.], ack 351, win 1944, options [nop,nop,TS val 326480734 ecr 943307886], length 0 13:28:01.316229 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [P.], seq 351:353, ack 1, win 8235, options [nop,nop,TS val 943307886 ecr 326480733], length 2 13:28:01.316242 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [.], ack 353, win 1944, options [nop,nop,TS val 326480734 ecr 943307886], length 0 13:28:01.321019 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [P.], seq 1:18, ack 353, win 1944, options [nop,nop,TS val 326480735 ecr 943307886], length 17 13:28:01.321294 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [FP.], seq 18:684, ack 353, win 1944, options [nop,nop,TS val 326480736 ecr 943307886], length 666 13:28:01.321386 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [R.], seq 685, ack 353, win 1944, options [nop,nop,TS val 326480736 ecr 943307886], length 0 13:28:01.322727 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [.], ack 18, win 8234, options [nop,nop,TS val 943307891 ecr 326480735], length 0 13:28:01.322733 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [R], seq 3103085800, win 0, length 0 13:28:01.323221 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [.], ack 685, win 8192, options [nop,nop,TS val 943307892 ecr 326480736], length 0 13:28:01.323231 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [R], seq 3103086467, win 0, length 0 ~~~~~~~~~~~~~~~~~~~~ Bad1 -- Client Side ~~~~~~~~~~~~~~~~~~~~ 13:28:11.374654 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [S], seq 920400580, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 943307883 ecr 0,sackOK,eol], length 0 13:28:11.375764 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [S.], seq 3103085782, ack 920400581, win 14480, options [mss 1460,sackOK,TS val 326480733 ecr 943307883,nop,wscale 3], length 0 13:28:11.376352 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [.], ack 1, win 8235, options [nop,nop,TS val 943307884 ecr 326480733], length 0 13:28:11.378252 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [P.], seq 1:351, ack 1, win 8235, options [nop,nop,TS val 943307886 ecr 326480733], length 350 13:28:11.379027 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [P.], seq 351:353, ack 1, win 8235, options [nop,nop,TS val 943307886 ecr 326480733], length 2 13:28:11.379732 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [.], ack 351, win 1944, options [nop,nop,TS val 326480734 ecr 943307886], length 0 13:28:11.380592 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [.], ack 353, win 1944, options [nop,nop,TS val 326480734 ecr 943307886], length 0 13:28:11.384968 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [P.], seq 1:18, ack 353, win 1944, options [nop,nop,TS val 326480735 ecr 943307886], length 17 13:28:11.385044 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [.], ack 18, win 8234, options [nop,nop,TS val 943307891 ecr 326480735], length 0 13:28:11.385586 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [FP.], seq 18:684, ack 353, win 1944, options [nop,nop,TS val 326480736 ecr 943307886], length 666 13:28:11.385743 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [.], ack 685, win 8192, options [nop,nop,TS val 943307892 ecr 326480736], length 0 13:28:11.385966 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [R.], seq 685, ack 353, win 1944, options [nop,nop,TS val 326480736 ecr 943307886], length 0 13:28:11.387343 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [R], seq 3103085800, win 0, length 0 13:28:11.387344 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [R], seq 3103086467, win 0, length 0 ~~~~~~~~~~~~~~~~~~~~ Bad2 -- Server Side ~~~~~~~~~~~~~~~~~~~~ 13:28:01.319185 IP 192.168.1.51.51473 > 192.168.1.132.5000: Flags [S], seq 1631526992, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 943307889 ecr 0,sackOK,eol], length 0 13:28:01.319197 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [S.], seq 2524685719, ack 1631526993, win 14480, options [mss 1460,sackOK,TS val 326480735 ecr 943307889,nop,wscale 3], length 0 13:28:01.320692 IP 192.168.1.51.51473 > 192.168.1.132.5000: Flags [.], ack 1, win 8235, options [nop,nop,TS val 943307890 ecr 326480735], length 0 13:28:01.322219 IP 192.168.1.51.51473 > 192.168.1.132.5000: Flags [P.], seq 1:351, ack 1, win 8235, options [nop,nop,TS val 943307890 ecr 326480735], length 350 13:28:01.322336 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [.], ack 351, win 1944, options [nop,nop,TS val 326480736 ecr 943307890], length 0 13:28:01.322689 IP 192.168.1.51.51473 > 192.168.1.132.5000: Flags [P.], seq 351:353, ack 1, win 8235, options [nop,nop,TS val 943307890 ecr 326480735], length 2 13:28:01.322700 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [.], ack 353, win 1944, options [nop,nop,TS val 326480736 ecr 943307890], length 0 13:28:01.326307 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [P.], seq 1:18, ack 353, win 1944, options [nop,nop,TS val 326480737 ecr 943307890], length 17 13:28:01.326614 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [FP.], seq 18:684, ack 353, win 1944, options [nop,nop,TS val 326480737 ecr 943307890], length 666 13:28:01.326710 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [R.], seq 685, ack 353, win 1944, options [nop,nop,TS val 326480737 ecr 943307890], length 0 13:28:01.328499 IP 192.168.1.51.51473 > 192.168.1.132.5000: Flags [.], ack 18, win 8234, options [nop,nop,TS val 943307896 ecr 326480737], length 0 13:28:01.328509 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [R], seq 2524685737, win 0, length 0 13:28:01.328514 IP 192.168.1.51.51473 > 192.168.1.132.5000: Flags [.], ack 685, win 8192, options [nop,nop,TS val 943307896 ecr 326480737], length 0 13:28:01.328517 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [R], seq 2524686404, win 0, length 0

  Read the article

• xen 4.1 host priodically dropping network packets of domU

  - by Dyutiman Chakraborty

  I have xen 4.1 Host running on a ubuntu 12.04 LTS Server with ip 153.x.x.54. I have setup 2 VMs on it, namely, "dev.mydomain.com" and "web.mydomain.com" with ips 195.X.X.2 and 195.x.x.3 respectively. For network the VMs connect through xendbr0 (xen-bridge), and can accces the network properly. I can also login to the VMs with ssh with no issue. However when I ping any of the VMs, there is a high amount of periodic packet drop. If I the ping the xen host (dom0) there is no packet drop. Following is a output of "tcpdump | grep ICMP" on dOM0 while I was pinging one of the domU tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 05:19:55.682493 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 30, length 64 05:19:56.691144 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 31, length 64 05:19:57.698776 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 32, length 64 05:19:58.706784 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 33, length 64 05:19:59.714751 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 34, length 64 05:20:00.723144 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 35, length 64 05:20:01.730349 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 36, length 64 05:20:02.739017 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 37, length 64 05:20:03.746806 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 38, length 64 05:20:06.770326 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 41, length 64 05:20:07.778801 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 42, length 64 05:20:08.786481 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 43, length 64 05:20:09.794720 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 44, length 64 05:20:10.802395 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 45, length 64 05:20:11.810770 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 46, length 64 05:20:12.818511 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 47, length 64 05:20:13.826817 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 48, length 64 05:20:14.835125 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 49, length 64 05:20:15.842138 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3460, seq 50, length 64 05:20:18.274072 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 1, length 64 05:20:19.282347 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 2, length 64 05:20:20.290746 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 3, length 64 05:20:21.297910 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 4, length 64 05:20:22.305656 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 5, length 64 05:20:23.314369 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 6, length 64 05:20:24.322055 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 7, length 64 05:20:25.329782 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 8, length 64 05:20:26.338473 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 9, length 64 05:20:27.346411 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 10, length 64 05:20:28.354175 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 11, length 64 05:20:29.361640 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 12, length 64 05:20:30.370026 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 13, length 64 05:20:31.377696 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 14, length 64 05:20:32.386151 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 15, length 64 05:20:33.394118 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 16, length 64 05:20:34.402058 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 17, length 64 05:20:35.409002 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 18, length 64 05:20:36.417692 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > web.mydomain.com: ICMP echo request, id 3461, seq 19, length 64 05:20:36.496916 IP6 fe80::3285:a9ff:feec:fc69 > ip6-allnodes: HBH ICMP6, multicast listener querymax resp delay: 1000 addr: ::, length 24 05:20:36.499112 IP6 fe80::21c:c0ff:fe6c:c091 > ff02::1:ff6c:c091: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff6c:c091, length 24 05:20:36.507041 IP6 fe80::227:eff:fe11:fa3f > ff02::1:ff00:2: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff00:2, length 24 05:20:36.523919 IP6 fe80::21c:c0ff:fe77:6257 > ff02::1:ff77:6257: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff77:6257, length 24 05:20:36.544785 IP6 fe80::54:ff:fe12:ea9a > ff02::1:ff12:ea9a: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff12:ea9a, length 24 05:20:36.581740 IP6 fe80::5604:a6ff:fef1:6da7 > ff02::1:fff1:6da7: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:fff1:6da7, length 24 05:20:36.600103 IP6 fe80::8a8:8aa0:5e18:917a > ff02::1:ff18:917a: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff18:917a, length 24 05:20:36.601989 IP6 fe80::227:eff:fe11:fa3e > ff02::1:ff11:fa3e: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff11:fa3e, length 24 05:20:36.611090 IP6 fe80::dcad:56ff:fe57:3bbe > ff02::1:ff57:3bbe: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff57:3bbe, length 24 05:20:36.660521 IP6 fe80::54:ff:fe02:1d31 > ff02::1:ff00:6: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff00:6, length 24 05:20:36.698871 IP6 fe80::21e:8cff:feb4:9f89 > ff02::1:ffb4:9f89: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ffb4:9f89, length 24 05:20:36.776548 IP6 fe80::54:ff:fe12:ea9a > ff02::1:ff01:7: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff01:7, length 24 05:20:36.781910 IP6 fe80::54:ff:fe8f:6dd > ff02::1:ff00:3: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff00:3, length 24 05:20:36.865475 IP6 fe80::21c:c0ff:fe4a:ae9f > ff02::1:ff4a:ae9f: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff4a:ae9f, length 24 05:20:36.908333 IP6 fe80::dcad:45ff:fe90:84db > ff02::1:ff90:84db: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff90:84db, length 24 05:20:36.919653 IP6 fe80::54:ff:fe12:ea9a > ff02::1:ff00:7: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff00:7, length 24 05:20:36.924276 IP6 fe80::59a2:2a4a:2082:6dee > ff02::1:ff82:6dee: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff82:6dee, length 24 05:20:37.001905 IP6 fe80::54:ff:fe8f:6dd > ff02::1:ff8f:6dd: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff8f:6dd, length 24 05:20:37.042403 IP6 fe80::54:ff:fe95:54f2 > ff02::1:ff95:54f2: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff95:54f2, length 24 05:20:37.090992 IP6 fe80::21c:c0ff:fe77:62ac > ff02::1:ff77:62ac: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff77:62ac, length 24 05:20:37.098118 IP6 fe80::d63d:7eff:fe01:b67f > ff02::1:ff01:b67f: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff01:b67f, length 24 05:20:37.118784 IP6 fe80::54:ff:fe12:ea9a > ff02::202: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::202, length 24 05:20:37.168548 IP6 fe80::54:ff:fe02:1d31 > ff02::1:ff02:1d31: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff02:1d31, length 24 05:20:41.743286 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 1, length 64 05:20:41.743542 IP dev.mydomain.com > ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in: ICMP echo reply, id 3463, seq 1, length 64 05:20:42.743859 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 2, length 64 05:20:42.743952 IP dev.mydomain.com > ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in: ICMP echo reply, id 3463, seq 2, length 64 05:20:43.745689 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 3, length 64 05:20:43.745777 IP dev.mydomain.com > ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in: ICMP echo reply, id 3463, seq 3, length 64 05:20:44.746706 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 4, length 64 05:20:44.746796 IP dev.mydomain.com > ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in: ICMP echo reply, id 3463, seq 4, length 64 05:20:45.747986 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 5, length 64 05:20:45.748082 IP dev.mydomain.com > ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in: ICMP echo reply, id 3463, seq 5, length 64 05:20:46.749834 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 6, length 64 05:20:46.749920 IP dev.mydomain.com > ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in: ICMP echo reply, id 3463, seq 6, length 64 05:20:47.750838 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 7, length 64 05:20:47.751182 IP dev.mydomain.com > ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in: ICMP echo reply, id 3463, seq 7, length 64 05:20:48.751909 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 8, length 64 05:20:48.751991 IP dev.mydomain.com > ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in: ICMP echo reply, id 3463, seq 8, length 64 05:20:49.752542 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 9, length 64 05:20:49.752620 IP dev.mydomain.com > ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in: ICMP echo reply, id 3463, seq 9, length 64 05:20:50.754246 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 10, length 64 05:20:51.753856 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 11, length 64 05:20:52.752868 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 12, length 64 05:20:53.754174 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 13, length 64 05:20:54.753972 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 14, length 64 05:20:55.753814 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 15, length 64 05:20:56.753391 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 16, length 64 05:20:57.753683 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 17, length 64 05:20:58.753487 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 18, length 64 05:20:59.754013 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 19, length 64 05:21:00.753169 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 20, length 64 05:21:01.753757 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 21, length 64 05:21:02.753307 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 22, length 64 05:21:03.753021 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 23, length 64 05:21:04.753628 IP ABTS-North-Dynamic-226.X.X.122.airtelbroadband.in > dev.mydomain.com: ICMP echo request, id 3463, seq 24, length 64 ^C479 packets captured 718 packets received by filter 238 packets dropped by kernel 3 packets dropped by interface You see the ping request is not responed to initially, then for a moment it is replied back and then again no reply. I have tried everything (to the best of my knowledge) to fix this, but can't find any answer Any help will be greatly appreciated Thanks.

  Read the article

• unexplainable packet drops with 5 ethernet NICs and low traffic on Ubuntu

  - by jon

  I'm stuck on problem where my machine started to drops packets with no sign of ANY system load or high interrupt usage after an upgrade to Ubuntu 12.04. My server is a network monitoring sensor, running Ubuntu LTS 12.04, it passively collects packets from 5 interfaces doing network intrusion type stuff. Before the upgrade I managed to collect 200+GB of packets a day while writing them to disk with around 0% packet loss depending on the day with the help of CPU affinity and NIC IRQ to CPU bindings. Now I lose a great deal of packets with none of my applications running and at very low PPS rate which a modern workstation NIC would have no trouble with. Specs: x64 Xeon 4 cores 3.2 Ghz 16 GB RAM NICs: 5 Intel Pro NICs using the e1000 driver (NAPI). [1] eth0 and eth1 are integrated NICs (in the motherboard) There are 2 other PCI-X network cards, each with 2 Ethernet ports. 3 of the interfaces are running at Gigabit Ethernet, the others are not because they're attached to hubs. Specs: [2] http://support.dell.com/support/edocs/systems/pe2850/en/ug/t1390aa.htm uptime 17:36:00 up 1:43, 2 users, load average: 0.00, 0.01, 0.05 # uname -a Linux nms 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux I also have the CPU governor set to performance mode and irqbalance off. The problem still occurs with them on. # lspci -t -vv -[0000:00]-+-00.0 Intel Corporation E7520 Memory Controller Hub +-02.0-[01-03]--+-00.0-[02]----0e.0 Dell PowerEdge Expandable RAID controller 4 | \-00.2-[03]-- +-04.0-[04]-- +-05.0-[05-07]--+-00.0-[06]----07.0 Intel Corporation 82541GI Gigabit Ethernet Controller | \-00.2-[07]----08.0 Intel Corporation 82541GI Gigabit Ethernet Controller +-06.0-[08-0a]--+-00.0-[09]--+-04.0 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | | \-04.1 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | \-00.2-[0a]--+-02.0 Digium, Inc. Wildcard TE210P/TE212P dual-span T1/E1/J1 card 3.3V | +-03.0 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | \-03.1 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) +-1d.0 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 +-1d.1 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 +-1d.2 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 +-1d.7 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller +-1e.0-[0b]----0d.0 Advanced Micro Devices [AMD] nee ATI RV100 QY [Radeon 7000/VE] +-1f.0 Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge \-1f.1 Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller I believe the NIC nor the NIC drivers are dropping the packets because ethtool reports 0 under rx_missed_errors and rx_no_buffer_count for each interface. On the old system, if it couldn't keep up this is where the drops would be. I drop packets on multiple interfaces just about every second, usually in small increments of 2-4. I tried all these sysctl values, I'm currently using the uncommented ones. # cat /etc/sysctl.conf # high net.core.netdev_max_backlog = 3000000 net.core.rmem_max = 16000000 net.core.rmem_default = 8000000 # defaults #net.core.netdev_max_backlog = 1000 #net.core.rmem_max = 131071 #net.core.rmem_default = 163480 # moderate #net.core.netdev_max_backlog = 10000 #net.core.rmem_max = 33554432 #net.core.rmem_default = 33554432 Here's an example of an interface stats report with ethtool. They are all the same, nothing is out of the ordinary ( I think ), so I'm only going to show one: ethtool -S eth2 NIC statistics: rx_packets: 7498 tx_packets: 0 rx_bytes: 2722585 tx_bytes: 0 rx_broadcast: 327 tx_broadcast: 0 rx_multicast: 1504 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 1504 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 0 tx_tcp_seg_failed: 0 rx_flow_control_xon: 0 rx_flow_control_xoff: 0 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 2722585 rx_csum_offload_good: 0 rx_csum_offload_errors: 0 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 01 # ifconfig eth0 Link encap:Ethernet HWaddr 00:11:43:e0:e2:8c UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:373348 errors:16 dropped:95 overruns:0 frame:16 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:356830572 (356.8 MB) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 00:11:43:e0:e2:8d UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:13616 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8690528 (8.6 MB) TX bytes:0 (0.0 B) eth2 Link encap:Ethernet HWaddr 00:04:23:e1:77:6a UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:7750 errors:0 dropped:471 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2780935 (2.7 MB) TX bytes:0 (0.0 B) eth3 Link encap:Ethernet HWaddr 00:04:23:e1:77:6b UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:5112 errors:0 dropped:206 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:639472 (639.4 KB) TX bytes:0 (0.0 B) eth4 Link encap:Ethernet HWaddr 00:04:23:b6:35:6c UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:961467 errors:0 dropped:935 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:958561305 (958.5 MB) TX bytes:0 (0.0 B) eth5 Link encap:Ethernet HWaddr 00:04:23:b6:35:6d inet addr:192.168.1.6 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4264 errors:0 dropped:16 overruns:0 frame:0 TX packets:699 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:572228 (572.2 KB) TX bytes:124456 (124.4 KB) I tried the defaults, then started to play around with settings. I wasn't using any flow control and I increased the RxDescriptor count to 4096 before the upgrade as well without any problems. # cat /etc/modprobe.d/e1000.conf options e1000 XsumRX=0,0,0,0,0 RxDescriptors=4096,4096,4096,4096,4096 FlowControl=0,0,0,0,0 debug=16 Here's my network configuration file, I turned off checksumming and various offloading mechanisms along with setting CPU affinity with heavy use interfaces getting an entire CPU and light use interfaces sharing a CPU. I used these settings prior to the upgrade without problems. # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet manual pre-up /sbin/ethtool -G eth0 rx 4096 tx 0 pre-up /sbin/ethtool -K eth0 gro off gso off rx off pre-up /sbin/ethtool -A eth0 rx off autoneg off up ifconfig eth0 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/48/smp_affinity down ifconfig eth0 down post-down /sbin/ethtool -G eth0 rx 256 tx 256 post-down /sbin/ethtool -K eth0 gro on gso on rx on post-down /sbin/ethtool -A eth0 rx on autoneg on auto eth1 iface eth1 inet manual pre-up /sbin/ethtool -G eth1 rx 4096 tx 0 pre-up /sbin/ethtool -K eth1 gro off gso off rx off pre-up /sbin/ethtool -A eth1 rx off autoneg off up ifconfig eth1 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/49/smp_affinity down ifconfig eth1 down post-down /sbin/ethtool -G eth1 rx 256 tx 256 post-down /sbin/ethtool -K eth1 gro on gso on rx on post-down /sbin/ethtool -A eth1 rx on autoneg on auto eth2 iface eth2 inet manual pre-up /sbin/ethtool -G eth2 rx 4096 tx 0 pre-up /sbin/ethtool -K eth2 gro off gso off rx off pre-up /sbin/ethtool -A eth2 rx off autoneg off up ifconfig eth2 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "1" > /proc/irq/82/smp_affinity down ifconfig eth2 down post-down /sbin/ethtool -G eth2 rx 256 tx 256 post-down /sbin/ethtool -K eth2 gro on gso on rx on post-down /sbin/ethtool -A eth2 rx on autoneg on auto eth3 iface eth3 inet manual pre-up /sbin/ethtool -G eth3 rx 4096 tx 0 pre-up /sbin/ethtool -K eth3 gro off gso off rx off pre-up /sbin/ethtool -A eth3 rx off autoneg off up ifconfig eth3 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "2" > /proc/irq/83/smp_affinity down ifconfig eth3 down post-down /sbin/ethtool -G eth3 rx 256 tx 256 post-down /sbin/ethtool -K eth3 gro on gso on rx on post-down /sbin/ethtool -A eth3 rx on autoneg on auto eth4 iface eth4 inet manual pre-up /sbin/ethtool -G eth4 rx 4096 tx 0 pre-up /sbin/ethtool -K eth4 gro off gso off rx off pre-up /sbin/ethtool -A eth4 rx off autoneg off up ifconfig eth4 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/77/smp_affinity down ifconfig eth4 down post-down /sbin/ethtool -G eth4 rx 256 tx 256 post-down /sbin/ethtool -K eth4 gro on gso on rx on post-down /sbin/ethtool -A eth4 rx on autoneg on auto eth5 iface eth5 inet static pre-up /etc/fw.conf address 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255 gateway 192.168.1.1 dns-nameservers 192.168.1.2 192.168.1.3 up ifconfig eth5 up post-up echo "8" > /proc/irq/77/smp_affinity down ifconfig eth5 down Here's a few examples of packet drops, i ran one after another, probabling totaling 3 or 4 seconds. You can see increases in the drops from the 1st and 3rd. This was a non-busy time, very little traffic. # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 225 lo: 0 eth2: 505 eth1: 0 eth5: 17 eth0: 105 eth4: 1034 # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 225 lo: 0 eth2: 507 eth1: 0 eth5: 17 eth0: 105 eth4: 1034 # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 227 lo: 0 eth2: 512 eth1: 0 eth5: 17 eth0: 105 eth4: 1039 I tried the pci=noacpi options. With and without, it's the same. This is what my interrupt stats looked like before the upgrade, after, with ACPI on PCI it showed multiple NICs bound to an interrupt and shared with other devices such as USB drives which I didn't like so I think i'm going to keep it with ACPI off as it's easier to designate sole purpose interrupts. Is there any advantage I would have using the default i.e. ACPI w/ PCI. ? # cat /etc/default/grub | grep CMD_LINE GRUB_CMDLINE_LINUX_DEFAULT="ipv6.disable=1 noacpi pci=noacpi" GRUB_CMDLINE_LINUX="" # cat /proc/interrupts CPU0 CPU1 CPU2 CPU3 0: 45 0 0 16 IO-APIC-edge timer 1: 1 0 0 7936 IO-APIC-edge i8042 2: 0 0 0 0 XT-PIC-XT-PIC cascade 6: 0 0 0 3 IO-APIC-edge floppy 8: 0 0 0 1 IO-APIC-edge rtc0 9: 0 0 0 0 IO-APIC-edge acpi 12: 0 0 0 1809 IO-APIC-edge i8042 14: 1 0 0 4498 IO-APIC-edge ata_piix 15: 0 0 0 0 IO-APIC-edge ata_piix 16: 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb2 18: 0 0 0 1350 IO-APIC-fasteoi uhci_hcd:usb4, radeon 19: 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb3 23: 0 0 0 4099 IO-APIC-fasteoi ehci_hcd:usb1 38: 0 0 0 61963 IO-APIC-fasteoi megaraid 48: 0 0 1002319 4 IO-APIC-fasteoi eth0 49: 0 0 38772 3 IO-APIC-fasteoi eth1 77: 0 0 130076 432159 IO-APIC-fasteoi eth4 78: 0 0 0 23917 IO-APIC-fasteoi eth5 82: 1329033 0 0 4 IO-APIC-fasteoi eth2 83: 0 4886525 0 6 IO-APIC-fasteoi eth3 NMI: 5 6 4 5 Non-maskable interrupts LOC: 61409 57076 64257 114764 Local timer interrupts SPU: 0 0 0 0 Spurious interrupts IWI: 0 0 0 0 IRQ work interrupts RES: 17956 25333 13436 14789 Rescheduling interrupts CAL: 22436 607 539 478 Function call interrupts TLB: 1525 1458 4600 4151 TLB shootdowns TRM: 0 0 0 0 Thermal event interrupts THR: 0 0 0 0 Threshold APIC interrupts MCE: 0 0 0 0 Machine check exceptions MCP: 16 16 16 16 Machine check polls ERR: 0 MIS: 0 Here's sample output of vmstat, showing the system. Barebones system right now. root@nms:~# vmstat -S m 1 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 14992 192 1029 0 0 56 2 419 29 1 0 99 0 0 0 0 14992 192 1029 0 0 0 0 922 27 0 0 100 0 0 0 0 14991 192 1029 0 0 0 36 763 50 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 646 35 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 722 54 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 793 27 0 0 100 0 ^C Here's dmesg output. I can't figure out why my PCI-X slots are negotiated as PCI. The network cards are all PCI-X with the exception of the integrated NICs that came with the server. In the output below it looks as if eth3 and eth2 negotiated at PCI-X speeds rather than PCI:66Mhz. Wouldn't they all drop to PCI:66Mhz? If your integrated NICs are PCI, as labeled below (eth0,eth1), then wouldn't all devices on your bus speed drop down to that slower bus speed? If not, I still don't know why only one of my NICs ( each has two ethernet ports) is labeled as PCI-X in the output below. Does that mean it is running at PCI-X speeds are is it showing that it's capable? # dmesg | grep e1000 [ 3678.349337] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 3678.349342] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 3678.349394] e1000 0000:06:07.0: PCI->APIC IRQ transform: INT A -> IRQ 48 [ 3678.409725] e1000 0000:06:07.0: Receive Descriptors set to 4096 [ 3678.409730] e1000 0000:06:07.0: Checksum Offload Disabled [ 3678.409734] e1000 0000:06:07.0: Flow Control Disabled [ 3678.586409] e1000 0000:06:07.0: eth0: (PCI:66MHz:32-bit) 00:11:43:e0:e2:8c [ 3678.586419] e1000 0000:06:07.0: eth0: Intel(R) PRO/1000 Network Connection [ 3678.586642] e1000 0000:07:08.0: PCI->APIC IRQ transform: INT A -> IRQ 49 [ 3678.649854] e1000 0000:07:08.0: Receive Descriptors set to 4096 [ 3678.649859] e1000 0000:07:08.0: Checksum Offload Disabled [ 3678.649863] e1000 0000:07:08.0: Flow Control Disabled [ 3678.826436] e1000 0000:07:08.0: eth1: (PCI:66MHz:32-bit) 00:11:43:e0:e2:8d [ 3678.826444] e1000 0000:07:08.0: eth1: Intel(R) PRO/1000 Network Connection [ 3678.826627] e1000 0000:09:04.0: PCI->APIC IRQ transform: INT A -> IRQ 82 [ 3679.093266] e1000 0000:09:04.0: Receive Descriptors set to 4096 [ 3679.093271] e1000 0000:09:04.0: Checksum Offload Disabled [ 3679.093275] e1000 0000:09:04.0: Flow Control Disabled [ 3679.130239] e1000 0000:09:04.0: eth2: (PCI-X:133MHz:64-bit) 00:04:23:e1:77:6a [ 3679.130246] e1000 0000:09:04.0: eth2: Intel(R) PRO/1000 Network Connection [ 3679.130449] e1000 0000:09:04.1: PCI->APIC IRQ transform: INT B -> IRQ 83 [ 3679.397312] e1000 0000:09:04.1: Receive Descriptors set to 4096 [ 3679.397318] e1000 0000:09:04.1: Checksum Offload Disabled [ 3679.397321] e1000 0000:09:04.1: Flow Control Disabled [ 3679.434350] e1000 0000:09:04.1: eth3: (PCI-X:133MHz:64-bit) 00:04:23:e1:77:6b [ 3679.434360] e1000 0000:09:04.1: eth3: Intel(R) PRO/1000 Network Connection [ 3679.434553] e1000 0000:0a:03.0: PCI->APIC IRQ transform: INT A -> IRQ 77 [ 3679.704072] e1000 0000:0a:03.0: Receive Descriptors set to 4096 [ 3679.704077] e1000 0000:0a:03.0: Checksum Offload Disabled [ 3679.704081] e1000 0000:0a:03.0: Flow Control Disabled [ 3679.738364] e1000 0000:0a:03.0: eth4: (PCI:33MHz:64-bit) 00:04:23:b6:35:6c [ 3679.738371] e1000 0000:0a:03.0: eth4: Intel(R) PRO/1000 Network Connection [ 3679.738538] e1000 0000:0a:03.1: PCI->APIC IRQ transform: INT B -> IRQ 78 [ 3680.046060] e1000 0000:0a:03.1: eth5: (PCI:33MHz:64-bit) 00:04:23:b6:35:6d [ 3680.046067] e1000 0000:0a:03.1: eth5: Intel(R) PRO/1000 Network Connection [ 3682.132415] e1000: eth0 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.224423] e1000: eth1 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.316385] e1000: eth2 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.408391] e1000: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 3682.500396] e1000: eth4 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 3682.708401] e1000: eth5 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX At first I thought it was the NIC drivers but I'm not so sure. I really have no idea where else to look at the moment. Any help is greatly appreciated as I'm struggling with this. If you need more information just ask. Thanks! [1]http://www.cs.fsu.edu/~baker/devices/lxr/http/source/linux/Documentation/networking/e1000.txt?v=2.6.11.8 [2] http://support.dell.com/support/edocs/systems/pe2850/en/ug/t1390aa.htm

  Read the article

• .htaccess not working (mod_rewrite)

  - by Mike Curry

  Edit: I am pretty sure my .htaccess file is NOT being executed, and the problem is NOT with my rewrite rules. I have not having any luck getting my .htaccess with mod_rewrite working. Basically all I am trying to do is remove 'www' from "http://www.site.com" and "https://www.site.com". If there is anything I am missing (conf files, etc let me know I willl update this) I jsut can't see whats wrong here... I am using a 1&1 VPS III Virtual private server... anyone ever have this issue? I am using Ubuntu 8.04 Server LTS. Here is my .htaccess file (located @ /var/www/site/trunk/html/) Options +FollowSymLinks RewriteEngine on RewriteCond %{HTTP_HOST} ^www\.(.*) [NC] RewriteRule (.*) //%1/$1 [L,R=301] My mod_rewrite is enabled: The auto regenerated sym link is there in mods-available and /usr/lib/apache2/modules/ contains mod_rewrite.so root@s15348441:/etc/apache2/mods-available# more rewrite.load LoadModule rewrite_module /usr/lib/apache2/modules/mod_rewrite.so root@s15348441:/var/log# apache2ctl -t -D DUMP_MODULES Loaded Modules: core_module (static) log_config_module (static) logio_module (static) mpm_prefork_module (static) http_module (static) so_module (static) alias_module (shared) auth_basic_module (shared) authn_file_module (shared) authz_default_module (shared) authz_groupfile_module (shared) authz_host_module (shared) authz_user_module (shared) autoindex_module (shared) cgi_module (shared) dir_module (shared) env_module (shared) mime_module (shared) negotiation_module (shared) php5_module (shared) rewrite_module (shared) setenvif_module (shared) ssl_module (shared) status_module (shared) Syntax OK My apache config files: apache2.conf # # Based upon the NCSA server configuration files originally by Rob McCool. # # This is the main Apache server configuration file. It contains the # configuration directives that give the server its instructions. # See http://httpd.apache.org/docs/2.2/ for detailed information about # the directives. # # Do NOT simply read the instructions in here without understanding # what they do. They're here only as hints or reminders. If you are unsure # consult the online docs. You have been warned. # # The configuration directives are grouped into three basic sections: # 1. Directives that control the operation of the Apache server process as a # whole (the 'global environment'). # 2. Directives that define the parameters of the 'main' or 'default' server, # which responds to requests that aren't handled by a virtual host. # These directives also provide default values for the settings # of all virtual hosts. # 3. Settings for virtual hosts, which allow Web requests to be sent to # different IP addresses or hostnames and have them handled by the # same Apache server process. # # Configuration and logfile names: If the filenames you specify for many # of the server's control files begin with "/" (or "drive:/" for Win32), the # server will use that explicit path. If the filenames do *not* begin # with "/", the value of ServerRoot is prepended -- so "/var/log/apache2/foo.log" # with ServerRoot set to "" will be interpreted by the # server as "//var/log/apache2/foo.log". # ### Section 1: Global Environment # # The directives in this section affect the overall operation of Apache, # such as the number of concurrent requests it can handle or where it # can find its configuration files. # # # ServerRoot: The top of the directory tree under which the server's # configuration, error, and log files are kept. # # NOTE! If you intend to place this on an NFS (or otherwise network) # mounted filesystem then please read the LockFile documentation (available # at <URL:http://httpd.apache.org/docs-2.1/mod/mpm_common.html#lockfile>); # you will save yourself a lot of trouble. # # Do NOT add a slash at the end of the directory path. # ServerRoot "/etc/apache2" # # The accept serialization lock file MUST BE STORED ON A LOCAL DISK. # #<IfModule !mpm_winnt.c> #<IfModule !mpm_netware.c> LockFile /var/lock/apache2/accept.lock #</IfModule> #</IfModule> # # PidFile: The file in which the server should record its process # identification number when it starts. # This needs to be set in /etc/apache2/envvars # PidFile ${APACHE_PID_FILE} # # Timeout: The number of seconds before receives and sends time out. # Timeout 300 # # KeepAlive: Whether or not to allow persistent connections (more than # one request per connection). Set to "Off" to deactivate. # KeepAlive On # # MaxKeepAliveRequests: The maximum number of requests to allow # during a persistent connection. Set to 0 to allow an unlimited amount. # We recommend you leave this number high, for maximum performance. # MaxKeepAliveRequests 100 # # KeepAliveTimeout: Number of seconds to wait for the next request from the # same client on the same connection. # KeepAliveTimeout 15 ## ## Server-Pool Size Regulation (MPM specific) ## # prefork MPM # StartServers: number of server processes to start # MinSpareServers: minimum number of server processes which are kept spare # MaxSpareServers: maximum number of server processes which are kept spare # MaxClients: maximum number of server processes allowed to start # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # worker MPM # StartServers: initial number of server processes to start # MaxClients: maximum number of simultaneous client connections # MinSpareThreads: minimum number of worker threads which are kept spare # MaxSpareThreads: maximum number of worker threads which are kept spare # ThreadsPerChild: constant number of worker threads in each server process # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_worker_module> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> # These need to be set in /etc/apache2/envvars User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} # # AccessFileName: The name of the file to look for in each directory # for additional configuration directives. See also the AllowOverride # directive. # AccessFileName .htaccess # # The following lines prevent .htaccess and .htpasswd files from being # viewed by Web clients. # <Files ~ "^\.ht"> Order allow,deny Deny from all </Files> # # DefaultType is the default MIME type the server will use for a document # if it cannot otherwise determine one, such as from filename extensions. # If your server contains mostly text or HTML documents, "text/plain" is # a good value. If most of your content is binary, such as applications # or images, you may want to use "application/octet-stream" instead to # keep browsers from trying to display binary files as though they are # text. # DefaultType text/plain # # HostnameLookups: Log the names of clients or just their IP addresses # e.g., www.apache.org (on) or 204.62.129.132 (off). # The default is off because it'd be overall better for the net if people # had to knowingly turn this feature on, since enabling it means that # each client request will result in AT LEAST one lookup request to the # nameserver. # HostnameLookups Off # ErrorLog: The location of the error log file. # If you do not specify an ErrorLog directive within a <VirtualHost> # container, error messages relating to that virtual host will be # logged here. If you *do* define an error logfile for a <VirtualHost> # container, that host's errors will be logged there and not here. # ErrorLog /var/log/apache2/error.log # # LogLevel: Control the number of messages logged to the error_log. # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. # LogLevel warn # Include module configuration: Include /etc/apache2/mods-enabled/*.load Include /etc/apache2/mods-enabled/*.conf # Include all the user configurations: Include /etc/apache2/httpd.conf # Include ports listing Include /etc/apache2/ports.conf # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # If you are behind a reverse proxy, you might want to change %h into %{X-Forwarded-For}i # LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent # # ServerTokens # This directive configures what you return as the Server HTTP response # Header. The default is 'Full' which sends information about the OS-Type # and compiled in modules. # Set to one of: Full | OS | Minor | Minimal | Major | Prod # where Full conveys the most information, and Prod the least. # ServerTokens Full # # Optionally add a line containing the server version and virtual host # name to server-generated pages (internal error documents, FTP directory # listings, mod_status and mod_info output etc., but not CGI generated # documents or custom error documents). # Set to "EMail" to also include a mailto: link to the ServerAdmin. # Set to one of: On | Off | EMail # ServerSignature On # # Customizable error responses come in three flavors: # 1) plain text 2) local redirects 3) external redirects # # Some examples: #ErrorDocument 500 "The server made a boo boo." #ErrorDocument 404 /missing.html #ErrorDocument 404 "/cgi-bin/missing_handler.pl" #ErrorDocument 402 http://www.example.com/subscription_info.html # # # Putting this all together, we can internationalize error responses. # # We use Alias to redirect any /error/HTTP_<error>.html.var response to # our collection of by-error message multi-language collections. We use # includes to substitute the appropriate text. # # You can modify the messages' appearance without changing any of the # default HTTP_<error>.html.var files by adding the line: # # Alias /error/include/ "/your/include/path/" # # which allows you to create your own set of files by starting with the # /usr/share/apache2/error/include/ files and copying them to /your/include/path/, # even on a per-VirtualHost basis. The default include files will display # your Apache version number and your ServerAdmin email address regardless # of the setting of ServerSignature. # # The internationalized error documents require mod_alias, mod_include # and mod_negotiation. To activate them, uncomment the following 30 lines. # Alias /error/ "/usr/share/apache2/error/" # # <Directory "/usr/share/apache2/error"> # AllowOverride None # Options IncludesNoExec # AddOutputFilter Includes html # AddHandler type-map var # Order allow,deny # Allow from all # LanguagePriority en cs de es fr it nl sv pt-br ro # ForceLanguagePriority Prefer Fallback # </Directory> # # ErrorDocument 400 /error/HTTP_BAD_REQUEST.html.var # ErrorDocument 401 /error/HTTP_UNAUTHORIZED.html.var # ErrorDocument 403 /error/HTTP_FORBIDDEN.html.var # ErrorDocument 404 /error/HTTP_NOT_FOUND.html.var # ErrorDocument 405 /error/HTTP_METHOD_NOT_ALLOWED.html.var # ErrorDocument 408 /error/HTTP_REQUEST_TIME_OUT.html.var # ErrorDocument 410 /error/HTTP_GONE.html.var # ErrorDocument 411 /error/HTTP_LENGTH_REQUIRED.html.var # ErrorDocument 412 /error/HTTP_PRECONDITION_FAILED.html.var # ErrorDocument 413 /error/HTTP_REQUEST_ENTITY_TOO_LARGE.html.var # ErrorDocument 414 /error/HTTP_REQUEST_URI_TOO_LARGE.html.var # ErrorDocument 415 /error/HTTP_UNSUPPORTED_MEDIA_TYPE.html.var # ErrorDocument 500 /error/HTTP_INTERNAL_SERVER_ERROR.html.var # ErrorDocument 501 /error/HTTP_NOT_IMPLEMENTED.html.var # ErrorDocument 502 /error/HTTP_BAD_GATEWAY.html.var # ErrorDocument 503 /error/HTTP_SERVICE_UNAVAILABLE.html.var # ErrorDocument 506 /error/HTTP_VARIANT_ALSO_VARIES.html.var # Include of directories ignores editors' and dpkg's backup files, # see README.Debian for details. # Include generic snippets of statements Include /etc/apache2/conf.d/ # Include the virtual host configurations: Include /etc/apache2/sites-enabled/ My default config file for www on apache NameVirtualHost *:80 <VirtualHost *:80> ServerAdmin [email protected] #SSLEnable #SSLVerifyClient none #SSLCertificateFile /usr/local/ssl/crt/public.crt #SSLCertificateKeyFile /usr/local/ssl/private/private.key DocumentRoot /var/www/site/trunk/html <Directory /> Options FollowSymLinks AllowOverride all </Directory> <Directory /var/www/site/trunk/html> Options Indexes FollowSymLinks MultiViews AllowOverride all Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> My ssl config file NameVirtualHost *:443 <VirtualHost *:443> ServerAdmin [email protected] #SSLEnable #SSLVerifyClient none #SSLCertificateFile /usr/local/ssl/crt/public.crt #SSLCertificateKeyFile /usr/local/ssl/private/private.key DocumentRoot /var/www/site/trunk/html <Directory /> Options FollowSymLinks AllowOverride all </Directory> <Directory /var/www/site/trunk/html> Options Indexes FollowSymLinks MultiViews AllowOverride all Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn SSLEngine On SSLCertificateFile /usr/local/ssl/crt/public.crt SSLCertificateKeyFile /usr/local/ssl/private/private.key CustomLog /var/log/apache2/access.log combined ServerSignature On Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> My /etc/apache2/httpd.conf is blank The directory /etc/apache2/conf.d has nothing in it but one file (charset) contents of /etc/apache2/conf.dcharset # Read the documentation before enabling AddDefaultCharset. # In general, it is only a good idea if you know that all your files # have this encoding. It will override any encoding given in the files # in meta http-equiv or xml encoding tags. #AddDefaultCharset UTF-8 My apache error.log [Wed Jun 03 00:12:31 2009] [error] [client 216.168.43.234] client sent HTTP/1.1 request without hostname (see RFC2616 section 14.23): /w00tw00t.at.ISC.SANS.DFind:) [Wed Jun 03 05:03:51 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 05:03:54 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 05:13:48 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 05:13:51 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 05:13:54 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 05:13:57 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 05:17:28 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 05:26:23 2009] [notice] caught SIGWINCH, shutting down gracefully [Wed Jun 03 05:26:34 2009] [notice] Apache/2.2.8 (Ubuntu) PHP/5.2.4-2ubuntu5.6 with Suhosin-Patch mod_ssl/2.2.8 OpenSSL/0.9.8g configured -- resuming normal operations [Wed Jun 03 06:03:41 2009] [notice] caught SIGWINCH, shutting down gracefully [Wed Jun 03 06:03:51 2009] [notice] Apache/2.2.8 (Ubuntu) PHP/5.2.4-2ubuntu5.6 with Suhosin-Patch mod_ssl/2.2.8 OpenSSL/0.9.8g configured -- resuming normal operations [Wed Jun 03 06:25:07 2009] [notice] caught SIGWINCH, shutting down gracefully [Wed Jun 03 06:25:17 2009] [notice] Apache/2.2.8 (Ubuntu) PHP/5.2.4-2ubuntu5.6 with Suhosin-Patch mod_ssl/2.2.8 OpenSSL/0.9.8g configured -- resuming normal operations [Wed Jun 03 12:09:25 2009] [error] [client 61.139.105.163] File does not exist: /var/www/site/trunk/html/fastenv [Wed Jun 03 15:04:42 2009] [notice] Graceful restart requested, doing restart [Wed Jun 03 15:04:43 2009] [notice] Apache/2.2.8 (Ubuntu) PHP/5.2.4-2ubuntu5.6 with Suhosin-Patch mod_ssl/2.2.8 OpenSSL/0.9.8g configured -- resuming normal operations [Wed Jun 03 15:29:51 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 15:29:54 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 15:30:32 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 15:45:54 2009] [notice] caught SIGWINCH, shutting down gracefully [Wed Jun 03 15:46:05 2009] [notice] Apache/2.2.8 (Ubuntu) PHP/5.2.4-2ubuntu5.6 with Suhosin-Patch mod_ssl/2.2.8 OpenSSL/0.9.8g configured -- resuming normal operations

  Read the article

• Using a mounted NTFS share with nginx

  - by Hoff

  I have set up a local testing VM with Ubuntu Server 12.04 LTS and the LEMP stack. It's kind of an unconventional setup because instead of having all my PHP scripts on the local machine, I've mounted an NTFS share as the document root because I do my development on Windows. I had everything working perfectly up until this morning, now I keep getting a dreaded 'File not found.' error. I am almost certain this must be somehow permission related, because if I copy my site over to /var/www, nginx and php-fpm have no problems serving my PHP scripts. What I can't figure out is why all of a sudden (after a reboot of the server), no PHP files will be served but instead just the 'File not found.' error. Static files work fine, so I think it's PHP that is causing the headache. Both nginx and php-fpm are configured to run as the user www-data: root@ubuntu-server:~# ps aux | grep 'nginx\|php-fpm' root 1095 0.0 0.0 5816 792 ? Ss 11:11 0:00 nginx: master process /opt/nginx/sbin/nginx -c /etc/nginx/nginx.conf www-data 1096 0.0 0.1 6016 1172 ? S 11:11 0:00 nginx: worker process www-data 1098 0.0 0.1 6016 1172 ? S 11:11 0:00 nginx: worker process root 1130 0.0 0.4 175560 4212 ? Ss 11:11 0:00 php-fpm: master process (/etc/php5/php-fpm.conf) www-data 1131 0.0 0.3 175560 3216 ? S 11:11 0:00 php-fpm: pool www www-data 1132 0.0 0.3 175560 3216 ? S 11:11 0:00 php-fpm: pool www www-data 1133 0.0 0.3 175560 3216 ? S 11:11 0:00 php-fpm: pool www root 1686 0.0 0.0 4368 816 pts/1 S+ 11:11 0:00 grep --color=auto nginx\|php-fpm I have mounted the NTFS share at /mnt/webfiles by editing /etc/fstab and adding the following line: //192.168.0.199/c$/Websites/ /mnt/webfiles cifs username=Jordan,password=mypasswordhere,gid=33,uid=33 0 0 Where gid 33 is the www-data group and uid 33 is the user www-data. If I list the contents of one of my sites you can in fact see that they belong to the user www-data: root@ubuntu-server:~# ls -l /mnt/webfiles/nTv5-2.0 total 8 drwxr-xr-x 0 www-data www-data 0 Jun 6 19:12 app drwxr-xr-x 0 www-data www-data 0 Aug 22 19:00 assets -rwxr-xr-x 0 www-data www-data 1150 Jan 4 2012 favicon.ico -rwxr-xr-x 0 www-data www-data 1412 Dec 28 2011 index.php drwxr-xr-x 0 www-data www-data 0 Jun 3 16:44 lib drwxr-xr-x 0 www-data www-data 0 Jan 3 2012 plugins drwxr-xr-x 0 www-data www-data 0 Jun 3 16:45 vendors If I switch to the www-data user, I have no problem creating a new file on the share: root@ubuntu-server:~# su www-data $ > /mnt/webfiles/test.txt $ ls -l /mnt/webfiles | grep test\.txt -rwxr-xr-x 0 www-data www-data 0 Sep 8 11:19 test.txt There should be no problem reading or writing to the share with php-fpm running as the user www-data. When I examine the error log of nginx, it's filled with a bunch of lines that look like the following: 2012/09/08 11:22:36 [error] 1096#0: *1 FastCGI sent in stderr: "Primary script unknown" while reading response header from upstream, client: 192.168.0.199, server: , request: "GET / HTTP/1.1", upstream: "fastcgi://unix:/var/run/php5-fpm.sock:", host: "192.168.0.123" 2012/09/08 11:22:39 [error] 1096#0: *1 FastCGI sent in stderr: "Primary script unknown" while reading response header from upstream, client: 192.168.0.199, server: , request: "GET /apc.php HTTP/1.1", upstream: "fastcgi://unix:/var/run/php5-fpm.sock:", host: "192.168.0.123" It's bizarre that this was working previously and now all of sudden PHP is complaining that it can't "find" the scripts on the share. Does anybody know why this is happening? EDIT I tried editing php-fpm.conf and changing chdir to the following: chdir = /mnt/webfiles When I try and restart the php-fpm service, I get the error: Starting php-fpm [08-Sep-2012 14:20:55] ERROR: [pool www] the chdir path '/mnt/webfiles' does not exist or is not a directory This is a total load of bullshit because this directory DOES exist and is mounted! Any ls commands to list that directory work perfectly. Why the hell can't PHP-FPM see this directory?! Here are my configuration files for reference: nginx.conf user www-data; worker_processes 2; error_log /var/log/nginx/nginx.log info; pid /var/run/nginx.pid; events { worker_connections 1024; multi_accept on; } http { include fastcgi.conf; include mime.types; default_type application/octet-stream; set_real_ip_from 127.0.0.1; real_ip_header X-Forwarded-For; ## Proxy proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; client_max_body_size 32m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffers 32 4k; ## Compression gzip on; gzip_types text/plain text/css application/x-javascript text/xml application/xml application/xml+rss text/javascript; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; ### TCP options tcp_nodelay on; tcp_nopush on; keepalive_timeout 65; sendfile on; include /etc/nginx/sites-enabled/*; } my site config server { listen 80; access_log /var/log/nginx/$host.access.log; error_log /var/log/nginx/error.log; root /mnt/webfiles/nTv5-2.0/app/webroot; index index.php; ## Block bad bots if ($http_user_agent ~* (HTTrack|HTMLParser|libcurl|discobot|Exabot|Casper|kmccrew|plaNETWORK|RPT-HTTPClient)) { return 444; } ## Block certain Referers (case insensitive) if ($http_referer ~* (sex|vigra|viagra) ) { return 444; } ## Deny dot files: location ~ /\. { deny all; } ## Favicon Not Found location = /favicon.ico { access_log off; log_not_found off; } ## Robots.txt Not Found location = /robots.txt { access_log off; log_not_found off; } if (-f $document_root/maintenance.html) { rewrite ^(.*)$ /maintenance.html last; } location ~* \.(?:ico|css|js|gif|jpe?g|png)$ { # Some basic cache-control for static files to be sent to the browser expires max; add_header Pragma public; add_header Cache-Control "max-age=2678400, public, must-revalidate"; } location / { try_files $uri $uri/ index.php; if (-f $request_filename) { break; } rewrite ^(.+)$ /index.php?url=$1 last; } location ~ \.php$ { include /etc/nginx/fastcgi.conf; fastcgi_pass unix:/var/run/php5-fpm.sock; } } php-fpm.conf ;;;;;;;;;;;;;;;;;;;;; ; FPM Configuration ; ;;;;;;;;;;;;;;;;;;;;; ; All relative paths in this configuration file are relative to PHP's install ; prefix (/opt/php5). This prefix can be dynamicaly changed by using the ; '-p' argument from the command line. ; Include one or more files. If glob(3) exists, it is used to include a bunch of ; files from a glob(3) pattern. This directive can be used everywhere in the ; file. ; Relative path can also be used. They will be prefixed by: ; - the global prefix if it's been set (-p arguement) ; - /opt/php5 otherwise ;include=etc/fpm.d/*.conf ;;;;;;;;;;;;;;;;;; ; Global Options ; ;;;;;;;;;;;;;;;;;; [global] ; Pid file ; Note: the default prefix is /opt/php5/var ; Default Value: none pid = /var/run/php-fpm.pid ; Error log file ; Note: the default prefix is /opt/php5/var ; Default Value: log/php-fpm.log error_log = /var/log/php5-fpm/php-fpm.log ; Log level ; Possible Values: alert, error, warning, notice, debug ; Default Value: notice ;log_level = notice ; If this number of child processes exit with SIGSEGV or SIGBUS within the time ; interval set by emergency_restart_interval then FPM will restart. A value ; of '0' means 'Off'. ; Default Value: 0 ;emergency_restart_threshold = 0 ; Interval of time used by emergency_restart_interval to determine when ; a graceful restart will be initiated. This can be useful to work around ; accidental corruptions in an accelerator's shared memory. ; Available Units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;emergency_restart_interval = 0 ; Time limit for child processes to wait for a reaction on signals from master. ; Available units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;process_control_timeout = 0 ; Send FPM to background. Set to 'no' to keep FPM in foreground for debugging. ; Default Value: yes ;daemonize = yes ;;;;;;;;;;;;;;;;;;;; ; Pool Definitions ; ;;;;;;;;;;;;;;;;;;;; ; Multiple pools of child processes may be started with different listening ; ports and different management options. The name of the pool will be ; used in logs and stats. There is no limitation on the number of pools which ; FPM can handle. Your system will tell you anyway :) ; Start a new pool named 'www'. ; the variable $pool can we used in any directive and will be replaced by the ; pool name ('www' here) [www] ; Per pool prefix ; It only applies on the following directives: ; - 'slowlog' ; - 'listen' (unixsocket) ; - 'chroot' ; - 'chdir' ; - 'php_values' ; - 'php_admin_values' ; When not set, the global prefix (or /opt/php5) applies instead. ; Note: This directive can also be relative to the global prefix. ; Default Value: none ;prefix = /path/to/pools/$pool ; The address on which to accept FastCGI requests. ; Valid syntaxes are: ; 'ip.add.re.ss:port' - to listen on a TCP socket to a specific address on ; a specific port; ; 'port' - to listen on a TCP socket to all addresses on a ; specific port; ; '/path/to/unix/socket' - to listen on a unix socket. ; Note: This value is mandatory. ;listen = 127.0.0.1:9000 listen = /var/run/php5-fpm.sock ; Set listen(2) backlog. A value of '-1' means unlimited. ; Default Value: 128 (-1 on FreeBSD and OpenBSD) ;listen.backlog = -1 ; List of ipv4 addresses of FastCGI clients which are allowed to connect. ; Equivalent to the FCGI_WEB_SERVER_ADDRS environment variable in the original ; PHP FCGI (5.2.2+). Makes sense only with a tcp listening socket. Each address ; must be separated by a comma. If this value is left blank, connections will be ; accepted from any ip address. ; Default Value: any ;listen.allowed_clients = 127.0.0.1 ; Set permissions for unix socket, if one is used. In Linux, read/write ; permissions must be set in order to allow connections from a web server. Many ; BSD-derived systems allow connections regardless of permissions. ; Default Values: user and group are set as the running user ; mode is set to 0666 ;listen.owner = www-data ;listen.group = www-data ;listen.mode = 0666 ; Unix user/group of processes ; Note: The user is mandatory. If the group is not set, the default user's group ; will be used. user = www-data group = www-data ; Choose how the process manager will control the number of child processes. ; Possible Values: ; static - a fixed number (pm.max_children) of child processes; ; dynamic - the number of child processes are set dynamically based on the ; following directives: ; pm.max_children - the maximum number of children that can ; be alive at the same time. ; pm.start_servers - the number of children created on startup. ; pm.min_spare_servers - the minimum number of children in 'idle' ; state (waiting to process). If the number ; of 'idle' processes is less than this ; number then some children will be created. ; pm.max_spare_servers - the maximum number of children in 'idle' ; state (waiting to process). If the number ; of 'idle' processes is greater than this ; number then some children will be killed. ; Note: This value is mandatory. pm = dynamic ; The number of child processes to be created when pm is set to 'static' and the ; maximum number of child processes to be created when pm is set to 'dynamic'. ; This value sets the limit on the number of simultaneous requests that will be ; served. Equivalent to the ApacheMaxClients directive with mpm_prefork. ; Equivalent to the PHP_FCGI_CHILDREN environment variable in the original PHP ; CGI. ; Note: Used when pm is set to either 'static' or 'dynamic' ; Note: This value is mandatory. pm.max_children = 50 ; The number of child processes created on startup. ; Note: Used only when pm is set to 'dynamic' ; Default Value: min_spare_servers + (max_spare_servers - min_spare_servers) / 2 pm.start_servers = 20 ; The desired minimum number of idle server processes. ; Note: Used only when pm is set to 'dynamic' ; Note: Mandatory when pm is set to 'dynamic' pm.min_spare_servers = 5 ; The desired maximum number of idle server processes. ; Note: Used only when pm is set to 'dynamic' ; Note: Mandatory when pm is set to 'dynamic' pm.max_spare_servers = 35 ; The number of requests each child process should execute before respawning. ; This can be useful to work around memory leaks in 3rd party libraries. For ; endless request processing specify '0'. Equivalent to PHP_FCGI_MAX_REQUESTS. ; Default Value: 0 pm.max_requests = 500 ; The URI to view the FPM status page. If this value is not set, no URI will be ; recognized as a status page. By default, the status page shows the following ; information: ; accepted conn - the number of request accepted by the pool; ; pool - the name of the pool; ; process manager - static or dynamic; ; idle processes - the number of idle processes; ; active processes - the number of active processes; ; total processes - the number of idle + active processes. ; max children reached - number of times, the process limit has been reached, ; when pm tries to start more children (works only for ; pm 'dynamic') ; The values of 'idle processes', 'active processes' and 'total processes' are ; updated each second. The value of 'accepted conn' is updated in real time. ; Example output: ; accepted conn: 12073 ; pool: www ; process manager: static ; idle processes: 35 ; active processes: 65 ; total processes: 100 ; max children reached: 1 ; By default the status page output is formatted as text/plain. Passing either ; 'html' or 'json' as a query string will return the corresponding output ; syntax. Example: ; http://www.foo.bar/status ; http://www.foo.bar/status?json ; http://www.foo.bar/status?html ; Note: The value must start with a leading slash (/). The value can be ; anything, but it may not be a good idea to use the .php extension or it ; may conflict with a real PHP file. ; Default Value: not set pm.status_path = /status ; The ping URI to call the monitoring page of FPM. If this value is not set, no ; URI will be recognized as a ping page. This could be used to test from outside ; that FPM is alive and responding, or to ; - create a graph of FPM availability (rrd or such); ; - remove a server from a group if it is not responding (load balancing); ; - trigger alerts for the operating team (24/7). ; Note: The value must start with a leading slash (/). The value can be ; anything, but it may not be a good idea to use the .php extension or it ; may conflict with a real PHP file. ; Default Value: not set ping.path = /ping ; This directive may be used to customize the response of a ping request. The ; response is formatted as text/plain with a 200 response code. ; Default Value: pong ping.response = pong ; The timeout for serving a single request after which the worker process will ; be killed. This option should be used when the 'max_execution_time' ini option ; does not stop script execution for some reason. A value of '0' means 'off'. ; Available units: s(econds)(default), m(inutes), h(ours), or d(ays) ; Default Value: 0 ;request_terminate_timeout = 0 ; The timeout for serving a single request after which a PHP backtrace will be ; dumped to the 'slowlog' file. A value of '0s' means 'off'. ; Available units: s(econds)(default), m(inutes), h(ours), or d(ays) ; Default Value: 0 ;request_slowlog_timeout = 0 ; The log file for slow requests ; Default Value: not set ; Note: slowlog is mandatory if request_slowlog_timeout is set ;slowlog = log/$pool.log.slow ; Set open file descriptor rlimit. ; Default Value: system defined value ;rlimit_files = 1024 ; Set max core size rlimit. ; Possible Values: 'unlimited' or an integer greater or equal to 0 ; Default Value: system defined value ;rlimit_core = 0 ; Chroot to this directory at the start. This value must be defined as an ; absolute path. When this value is not set, chroot is not used. ; Note: you can prefix with '$prefix' to chroot to the pool prefix or one ; of its subdirectories. If the pool prefix is not set, the global prefix ; will be used instead. ; Note: chrooting is a great security feature and should be used whenever ; possible. However, all PHP paths will be relative to the chroot ; (error_log, sessions.save_path, ...). ; Default Value: not set ;chroot = ; Chdir to this directory at the start. ; Note: relative path can be used. ; Default Value: current directory or / when chroot ;chdir = /var/www ; Redirect worker stdout and stderr into main error log. If not set, stdout and ; stderr will be redirected to /dev/null according to FastCGI specs. ; Note: on highloaded environement, this can cause some delay in the page ; process time (several ms). ; Default Value: no ;catch_workers_output = yes ; Pass environment variables like LD_LIBRARY_PATH. All $VARIABLEs are taken from ; the current environment. ; Default Value: clean env ;env[HOSTNAME] = $HOSTNAME ;env[PATH] = /usr/local/bin:/usr/bin:/bin ;env[TMP] = /tmp ;env[TMPDIR] = /tmp ;env[TEMP] = /tmp ; Additional php.ini defines, specific to this pool of workers. These settings ; overwrite the values previously defined in the php.ini. The directives are the ; same as the PHP SAPI: ; php_value/php_flag - you can set classic ini defines which can ; be overwritten from PHP call 'ini_set'. ; php_admin_value/php_admin_flag - these directives won't be overwritten by ; PHP call 'ini_set' ; For php_*flag, valid values are on, off, 1, 0, true, false, yes or no. ; Defining 'extension' will load the corresponding shared extension from ; extension_dir. Defining 'disable_functions' or 'disable_classes' will not ; overwrite previously defined php.ini values, but will append the new value ; instead. ; Note: path INI options can be relative and will be expanded with the prefix ; (pool, global or /opt/php5) ; Default Value: nothing is defined by default except the values in php.ini and ; specified at startup with the -d argument ;php_admin_value[sendmail_path] = /usr/sbin/sendmail -t -i -f [email protected] ;php_flag[display_errors] = off ;php_admin_value[error_log] = /var/log/fpm-php.www.log ;php_admin_flag[log_errors] = on ;php_admin_value[memory_limit] = 32M php_admin_value[sendmail_path] = /usr/sbin/sendmail -t -i

  Read the article

< Previous Page | 59 60 61 62 63