Search Results

Search found 93603 results on 3745 pages for 'many to one'.

Page 63/3745 | < Previous Page | 59 60 61 62 63 64 65 66 67 68 69 70  | Next Page >

• DHCPDISCOVER requests from an off-by-one MAC address

  - by Aleksandr Levchuk

  In a Linux DHCP server I'm getting a bunch of these log lines: dhcpd: DHCPDISCOVER from 00:30:48:fe:5c:9c via eth1: network 192.168.2.0/24: no free leases I don't have any machines with 00:30:48:fe:5c:9c and I don't intend to give out an IP to 00:30:48:fe:5c:9c (whatever that could be). I tracked down the server that this is coming from and killed all the DHCP clients that were running but the DHCPDISCOVER requests do not stop. I can prove that this is the sending server by pulling the Ethernet cable - the requests stop. The strange thing is that the sending server only has 2 interfaces which are: 00:30:48:fe:5c:9a 00:30:48:fe:5c:9b What can be the cause of the off-by-one address? Who could be sending the requests? Details On the DHCP client: root@n34:~# ip link 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 100 link/ether 00:30:48:fe:5c:9a brd ff:ff:ff:ff:ff:ff 3: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000 link/ether 00:30:48:fe:5c:9b brd ff:ff:ff:ff:ff:ff 4: ib0: <BROADCAST,MULTICAST> mtu 2044 qdisc noop state DOWN qlen 256 link/infiniband 80:00:00:48:fe:80:00:00:00:00:00:00:00:02:c9:03:00:08:81:9f brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff 5: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast state UP qlen 256 link/infiniband 80:00:00:49:fe:80:00:00:00:00:00:00:00:02:c9:03:00:08:81:a0 brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff Same info: root@n34:~# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:30:48:fe:5c:9a inet addr:192.168.2.234 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:fefe:5c9a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:72544 errors:0 dropped:0 overruns:0 frame:0 TX packets:152773 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:4908592 (4.6 MiB) TX bytes:89815782 (85.6 MiB) Memory:dfd60000-dfd80000 eth1 Link encap:Ethernet HWaddr 00:30:48:fe:5c:9b UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Memory:dfde0000-dfe00000 ib0 Link encap:UNSPEC HWaddr 80-00-00-48-FE-80-00-00-00-00-00-00-00-00-00-00 BROADCAST MULTICAST MTU:2044 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:256 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ib1 Link encap:UNSPEC HWaddr 80-00-00-49-FE-80-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.3.234 Bcast:192.168.3.255 Mask:255.255.255.0 inet6 addr: fe80::202:c903:8:81a0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:2044 Metric:1 RX packets:1330 errors:0 dropped:0 overruns:0 frame:0 TX packets:255 errors:0 dropped:5 overruns:0 carrier:0 collisions:0 txqueuelen:256 RX bytes:716415 (699.6 KiB) TX bytes:17584 (17.1 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:560 (560.0 B) TX bytes:560 (560.0 B) The nodes were imaged with Perseus which uses kexec instead of rebooting.

  Read the article

• One email user keeps disconnecting from our exchange server

  - by Funky Si

  I have one user who keeps reporting that Outlook keeps disconnecting from our email server. All other users are fine. Our email server is running Exchange 2010 and the client is running Outlook 2003. The disconnection only lasts a moment. I have checked for logs on the client and Exchange server and can not see any reason for the disconnect, On the Client I get EventId 26 telling me Outlook has disconnected and reconnected but no reason why. Can anyone give me some suggestions of things to try and track down where the problem could be? --Update-- I have found the following log file C:\Program Files\Microsoft\Exchange Server\V14\Logging\RPC Client Access which suggests that it is a problem with RPC sessions. Excerpt is below 2013-01-31T15:21:24.015Z,6413,15,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,0,00:00:00,"BS=Conn:24,HangingConn:0,AD:$null/$null/0%,CAS:$null/$null/2%,AB:$null/$null/0%,RPC:$null/$null/1%,FC:$null/0,Policy:ClientThrottlingPolicy2,Norm[Resources:(Mdb)Mailbox Database 0765959540(Health:-1%,HistLoad:0),(Mdb)Public Folder Database 1945427388(Health:-1%,HistLoad:0),];GC:6/1/0;", 2013-01-31T15:21:24.015Z,6413,16,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,PublicLogoff,0,00:00:00,LogonId: 1, 2013-01-31T15:21:24.015Z,6413,16,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,,00:00:00,"BS=Conn:24,HangingConn:0,AD:$null/$null/0%,CAS:$null/$null/2%,AB:$null/$null/0%,RPC:$null/$null/1%,FC:$null/0,Policy:ClientThrottlingPolicy2,Norm[Resources:(Mdb)Mailbox Database 0765959540(Health:-1%,HistLoad:0),(Mdb)Public Folder Database 1945427388(Health:-1%,HistLoad:0),];GC:6/1/0;", 2013-01-31T15:21:24.015Z,6417,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,OwnerLogoff,0,00:00:00,LogonId: 0, 2013-01-31T15:21:24.015Z,6417,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,0x6BA (rpc::Exception),00:02:54.7668000,Budget Highs [AD = 0][CAS = 3][RPC = 1] Session Throttled Count = 0; SessionDropped,"RpcEndPoint: [ServerUnavailableException] Connection must be re-established - [SessionDeadException] Connection doesn't have any open logons, but has client activity. This may be masking synchronization stalls. Dropping a connection." 2013-01-31T15:21:24.015Z,6420,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,DelegateLogoff,0,00:00:00,LogonId: 0, 2013-01-31T15:21:24.031Z,6420,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,,00:00:00.0156000,Budget Highs [AD = 0][CAS = 3][RPC = 1] Session Throttled Count = 0, 2013-01-31T15:21:24.031Z,6420,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,Disconnect,0,00:02:54.2364000,, 2013-01-31T15:21:24.031Z,6419,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,OwnerLogoff,0,00:00:00,LogonId: 0, 2013-01-31T15:21:24.031Z,6419,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,,00:00:00,Budget Highs [AD = 0][CAS = 3][RPC = 1] Session Throttled Count = 0, 2013-01-31T15:21:24.031Z,6419,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,Disconnect,0,00:02:54.4392000,, 2013-01-31T15:21:24.031Z,6416,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,DelegateLogoff,0,00:00:00,LogonId: 0, 2013-01-31T15:21:24.031Z,6416,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,,00:00:00,Budget Highs [AD = 0][CAS = 3][RPC = 1] Session Throttled Count = 0, Can anyone help point me in the right direction for a solution?

  Read the article

• Connection drops while transferring large files to one server on a network

  - by Charlotte

  My company has two sites, each with their own LAN, using site to site VPN tunnel to connect the two sites. When transferring files (especially larger files) from site1 to site2 server1, the file transfer fails. I don't think this can be a VPN issue because transferring the same files to site2 server2 which is on the same network as server1 works fine. Pings to server1 and server2 at site2 from site1 are about the same, mostly 19/20ms with the odd one up to 50ms. As server1 is DB server with a high load I thought the NIC maybe overloaded, but a transfer from site2 server1 to site2 server2 works fine, and that uses the same NIC on server1 as transfers from site1 to site2 server1. The servers are both Windows Server 2003 VMs with VMXNET 3 NICs. Site2 Server1 route print: IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x10003 ...00 50 56 99 28 9b ...... vmxnet3 Ethernet Adapter #2 0x10004 ...00 50 56 99 18 97 ...... vmxnet3 Ethernet Adapter =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.20.10.1 172.20.10.18 10 10.10.10.0 255.255.255.0 10.10.10.70 10.10.10.70 10 10.10.10.70 255.255.255.255 127.0.0.1 127.0.0.1 10 10.255.255.255 255.255.255.255 10.10.10.70 10.10.10.70 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 172.20.10.0 255.255.255.0 172.20.10.18 172.20.10.18 10 172.20.10.18 255.255.255.255 127.0.0.1 127.0.0.1 10 172.20.255.255 255.255.255.255 172.20.10.18 172.20.10.18 10 224.0.0.0 240.0.0.0 10.10.10.70 10.10.10.70 10 224.0.0.0 240.0.0.0 172.20.10.18 172.20.10.18 10 255.255.255.255 255.255.255.255 10.10.10.70 10.10.10.70 1 255.255.255.255 255.255.255.255 172.20.10.18 172.20.10.18 1 Default Gateway: 172.20.10.1 =========================================================================== Persistent Routes: None Site2 Server2 route print IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x10003 ...00 50 56 99 15 00 ...... vmxnet3 Ethernet Adapter =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.20.10.1 172.20.10.114 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 172.20.10.0 255.255.255.0 172.20.10.114 172.20.10.114 10 172.20.10.114 255.255.255.255 127.0.0.1 127.0.0.1 10 172.20.255.255 255.255.255.255 172.20.10.114 172.20.10.114 10 224.0.0.0 240.0.0.0 172.20.10.114 172.20.10.114 10 255.255.255.255 255.255.255.255 172.20.10.114 172.20.10.114 1 Default Gateway: 172.20.10.1 =========================================================================== Persistent Routes: None Site1 Server route print: =========================================================================== Interface List 14...00 50 56 93 00 0b ......vmxnet3 Ethernet Adapter #2 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.168.1 192.168.168.118 261 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.168.0 255.255.255.0 On-link 192.168.168.118 261 192.168.168.118 255.255.255.255 On-link 192.168.168.118 261 192.168.168.255 255.255.255.255 On-link 192.168.168.118 261 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.168.118 261 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.168.118 261 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.168.1 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 14 261 fe80::/64 On-link 14 261 fe80::3c6b:996f:ef36:ee76/128 On-link 1 306 ff00::/8 On-link 14 261 ff00::/8 On-link =========================================================================== Persistent Routes: None tracert from site1 to site2 server1: Tracing route to server1 [172.20.10.18] over a maximum of 30 hops: 1 19 ms 19 ms 19 ms server1 [172.20.10.18] Trace complete. tracert from site2 server1 to site1: When this was run it went to the external IP of site2, then to a couple of external ips of the isp, then times out. Can anyone suggest any troubleshooting steps? Thanks, Charlotte.

  Read the article

• How long should one wait before going for a MS?

  - by Jungle Hunter

  Removed duplicate aspects of the question Hi! I'm an undergraduate Master's student. I've what seems to be a good offer in hand in Singapore (if location plays a role). Is an undergraduate Master's good enough for a Master's or one should go for MS? How much time should one wait (in their job) before going for a MS if that's the decision? Does one lose the progress which one makes while at the job before the Master's? Note: Undergraduate Master's is when my degree is called Master's but it is my first degree. This one is a four year one.

  Read the article

• IPTables masquerading with one NIC

  - by Tuinslak

  Hi, I am running an OpenVPN server with only one NIC. This is my current layout: public.ip > Cisco firewall > lan.ip > OpenVPN server lan.ip = 192.168.22.70 The Cisco firewall forwards the requests to the oVPN server, thus so far everything works and clients are able to connect. However, all clients connected should be able to access 3 networks: lan1: 192.168.200.0 (vpn lan) > tun0 lan2: 192.168.110.0 (office lan) > eth1 (gw 192.168.22.1) lan3: 192.168.22.0 (server lan) > eth1 (broadcast network) So tun0 is mapped to eth1. Iptables output: # iptables-save # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *filter :INPUT ACCEPT [327:26098] :FORWARD DROP [305:31700] :OUTPUT ACCEPT [291:27378] -A INPUT -i lo -j ACCEPT -A INPUT -i tun0 -j ACCEPT -A INPUT -i ! tun0 -p udp -m udp --dport 67 -j REJECT --reject-with icmp-port-unreachable -A INPUT -i ! tun0 -p udp -m udp --dport 53 -j REJECT --reject-with icmp-port-unreachable -A FORWARD -d 192.168.200.0/24 -i tun0 -j DROP -A FORWARD -s 192.168.200.0/24 -i tun0 -j ACCEPT -A FORWARD -d 192.168.200.0/24 -i eth1 -j ACCEPT COMMIT # Completed on Wed Feb 16 14:14:20 2011 # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *nat :PREROUTING ACCEPT [302:26000] :POSTROUTING ACCEPT [3:377] :OUTPUT ACCEPT [49:3885] -A POSTROUTING -o eth1 -j MASQUERADE COMMIT # Completed on Wed Feb 16 14:14:20 2011 Yet, clients are unable to ping any ip (including 192.168.200.1, which is the oVPN's IP) When the machine was directly connected to the internet, with 2 NICs, it was quite simply solved with masquerading and adding static routes in the oVPN client's config. However, as masquerading won't accept virtual interfaces (eth0:0, etc) I am unable to get masquerading to work again (and I'm not even sure whether I need virtual interfaces). Thanks. Edit: OpenVPN server: # ifconfig eth1 Link encap:Ethernet HWaddr ba:e6:64:ec:57:ac inet addr:192.168.22.70 Bcast:192.168.22.255 Mask:255.255.255.0 inet6 addr: fe80::b8e6:64ff:feec:57ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6857 errors:0 dropped:0 overruns:0 frame:0 TX packets:4044 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:584046 (570.3 KiB) TX bytes:473691 (462.5 KiB) Interrupt:14 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:33773 (32.9 KiB) TX bytes:33773 (32.9 KiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.1 P-t-P:192.168.200.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifconfig on a client: # ifconfig eth0 Link encap:Ethernet HWaddr 00:22:64:71:11:56 inet addr:192.168.110.94 Bcast:192.168.110.255 Mask:255.255.255.0 inet6 addr: fe80::222:64ff:fe71:1156/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3466 errors:0 dropped:0 overruns:0 frame:0 TX packets:1838 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:997924 (974.5 KiB) TX bytes:332406 (324.6 KiB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:37847 errors:0 dropped:0 overruns:0 frame:0 TX packets:37847 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2922444 (2.7 MiB) TX bytes:2922444 (2.7 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.30 P-t-P:192.168.200.29 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:689 errors:0 dropped:18 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:468778 (457.7 KiB) wlan0 Link encap:Ethernet HWaddr 00:16:ea:db:ae:86 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:704699 errors:0 dropped:0 overruns:0 frame:0 TX packets:730176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:520385963 (496.2 MiB) TX bytes:225210422 (214.7 MiB) static routes line at the end of the client's config (I've been playing around with the 192.168.200.0 -- (un)commenting to see if anything changes): route 192.168.200.0 255.255.255.0 route 192.168.110.0 255.255.255.0 route 192.168.22.0 255.255.255.0 route on a vpn client: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.200.29 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.22.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.200.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.110.1 0.0.0.0 UG 0 0 0 eth0 edit: Weirdly enough, if I set push "redirect-gateway def1" in the server config, (and thus routes all traffic through VPN, which is not what I want), it seems to work.

  Read the article

• I want to consolidate two sites into a third. Will my search engine rankings be penalized if I rewrite and redirect pages one by one?

  - by Patrick Kenny

  I have two Drupal sites with different content-- let's call them Apple and Orange. I recently developed a much more sophisticated third Drupal site-- let's call it Tree. For a large number of reasons, the content on Apple and Orange is useful for the users of Tree, so I want to move the content to Tree. However, much of the content is out of date. (This whole process took about five years.) To update the content, I will rewrite it one article at a time myself. Now here's my question: if I move the articles one by one (as I rewrite them) and then redirect the old articles (using a 301 redirect) on Apple/Orange to the new site on Tree, will this have a huge negative effect on my search engine rankings? Is there a good way to redirect among sites when they merge like this, or would I be better off keeping the old articles on Apple/Orange and simply linking them to the new, rewritten articles on Tree?

  Read the article

• Only One GPU Detected in the Nvidia Quadra NVS 450

  - by Kyle Brandt

  I just built myself an new workstation and now only 2 of 3 monitors are working. I built the nvidia driver by downloading it and installing with ./Nvidia... Before when I ran nvidia-settings I saw two GPUs listed but now I only see one. Xorg Config (Not sure how I ended up with 3 devices in there): # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:39 PDT 2010 Section "ServerLayout" # Removed Option "Xinerama" "1" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" RightOf "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor2" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:6:0:0" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:5:0:0" EndSection Section "Device" Identifier "Device2" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:3:0:0" EndSection Section "Screen" # Removed Option "TwinView" "0" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+0" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+275, DFP-3: nvidia-auto-select +1680+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-3" Option "metamodes" "DFP-0: nvidia-auto-select +0+0, DFP-3: nvidia-auto-select +1680+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" # Removed Option "metamodes" "DFP-3: nvidia-auto-select +0+0" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Device2" Monitor "Monitor2" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection lscpi: 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:02.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 2 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:10.0 PIC: Intel Corporation 5520/5500/X58 Physical and Link Layer Registers Port 0 (rev 13) 00:10.1 PIC: Intel Corporation 5520/5500/X58 Routing and Protocol Layer Registers Port 0 (rev 13) 00:11.0 PIC: Intel Corporation 5520/5500 Physical and Link Layer Registers Port 1 (rev 13) 00:11.1 PIC: Intel Corporation 5520/5500 Routing & Protocol Layer Register Port 1 (rev 13) 00:13.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub I/OxAPIC Interrupt Controller (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:15.0 PIC: Intel Corporation 5520/5500/X58 Trusted Execution Technology Registers (rev 13) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.3 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 4 00:1c.4 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 5 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller #1 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller #2 01:00.0 IDE interface: Device 1b4b:91a3 (rev 11) 02:00.0 USB Controller: NEC Corporation Device 0194 (rev 03) 03:00.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 04:00.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 04:02.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 05:00.0 3D controller: nVidia Corporation G98 [Quadro NVS 450] (rev a1) 06:00.0 VGA compatible controller: nVidia Corporation G98 [Quadro NVS 450] (rev a1) 08:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) 08:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) 09:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 09:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 0a:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 0b:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)

  Read the article

• Only One GPU Detected in the Nvidia Quadro NVS 450

  - by Kyle Brandt

  I just built myself an new workstation and now only 2 of 3 monitors are working. I built the nvidia driver by downloading it and installing with ./Nvidia... Before when I ran nvidia-settings I saw two GPUs listed but now I only see one. Xorg Config (Not sure how I ended up with 3 devices in there): # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:39 PDT 2010 Section "ServerLayout" # Removed Option "Xinerama" "1" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" RightOf "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor2" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:6:0:0" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:5:0:0" EndSection Section "Device" Identifier "Device2" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:3:0:0" EndSection Section "Screen" # Removed Option "TwinView" "0" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+0" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+275, DFP-3: nvidia-auto-select +1680+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-3" Option "metamodes" "DFP-0: nvidia-auto-select +0+0, DFP-3: nvidia-auto-select +1680+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" # Removed Option "metamodes" "DFP-3: nvidia-auto-select +0+0" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Device2" Monitor "Monitor2" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection lscpi: 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:02.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 2 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:10.0 PIC: Intel Corporation 5520/5500/X58 Physical and Link Layer Registers Port 0 (rev 13) 00:10.1 PIC: Intel Corporation 5520/5500/X58 Routing and Protocol Layer Registers Port 0 (rev 13) 00:11.0 PIC: Intel Corporation 5520/5500 Physical and Link Layer Registers Port 1 (rev 13) 00:11.1 PIC: Intel Corporation 5520/5500 Routing & Protocol Layer Register Port 1 (rev 13) 00:13.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub I/OxAPIC Interrupt Controller (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:15.0 PIC: Intel Corporation 5520/5500/X58 Trusted Execution Technology Registers (rev 13) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.3 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 4 00:1c.4 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 5 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller #1 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller #2 01:00.0 IDE interface: Device 1b4b:91a3 (rev 11) 02:00.0 USB Controller: NEC Corporation Device 0194 (rev 03) 03:00.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 04:00.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 04:02.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 05:00.0 3D controller: nVidia Corporation G98 [Quadro NVS 450] (rev a1) 06:00.0 VGA compatible controller: nVidia Corporation G98 [Quadro NVS 450] (rev a1) 08:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) 08:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) 09:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 09:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 0a:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 0b:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)

  Read the article

• Multiple Ruby versions on one webserver?

  - by Legion

  The Ideal Using rvm, it would be awesome to be able to have multiple Rubies on one webserver, and through some sort of server configuration, be able to assign Ruby versions to different Rails/Sinatra/etc apps on a per-project basis. I am aware, from rvm's documentation, that Passenger only works with one Ruby at a time. :( The Compromise Failing that, it would be nice to at least be able to concoct a way to be able to assign projects to a Ruby 1.8 or a Ruby 1.9 interpreter. I've read that using Nginx as a reverse proxy allows running Apache and Nginx on the same box. Would it then be possible to have Apache+Passenger using one Ruby, and Nginx+Passenger using a different one? Maybe use something other than Passenger with Nginx? Am I Barking Up the Wrong Tree? Am I missing a good solution to this issue? Am I walking into a nightmare configuration situation? Is what I want even viable, or is it necessary to run another box to run a separate Ruby version?

  Read the article

• WPF : Multiple views, one DataContext

  - by zapho

  Hi, I'm working on a WPF application which must handle multiple screens (two at this this time). One view can be opened on several screens and user actions must be reflected consistently on all screens. To achieve this, for a given type of view, a single DataContext is instantiated. Then, when a view is displayed on a screen, the unique DataContext is attached to it. So, one DataContext, several views (same type of view/xaml). So far so good. It works quite well in most cases. I do have a problem with a specific view which relies on ItemsControl. These ItemsControl are used to display UIElements dynamically build in the ViewModel/DataContext (C# code). These UIElements are mostly Path objects. Example : <ItemsControl ItemsSource="{Binding WindVectors}"> <ItemsControl.Template> <ControlTemplate TargetType="{x:Type ItemsControl}"> <Canvas IsItemsHost="True" /> </ControlTemplate> </ItemsControl.Template> </ItemsControl> Here, WindVectors is a ObservableCollection<UIElement>. When the view is opened the first time, everything is fine. The problem is that when the view is opened one another screen, all ItemsControl are removed from the first screen and displayed one the second screen. Other WPF components (TextBlock for instance) on this view react normally and are displayed on both screens. Any help would be greatly appreciated. Thanks. Fabrice

  Read the article

• Copy SQL Server data from one server to another on a schedule

  - by rwmnau

  I have a pair of SQL Servers at different webhosts, and I'm looking for a way to periodically update the one server using the other. Here's what I'm looking for: As automated as possible - ideally, without any involvement on my part once it's set up. Pushes a number of databases, in their entirely (including any schema changes) from one server to the other Freely allows changes on the source server without breaking my process. For this reason, I don't want to use replication, as I'd have to break it every time there's an update on the source, and then recreate the publication and subscription One database is about 4GB in size and contains binary data. I'm not sure if there's a way to export this to a script, but it would be a mammoth file if I did. Originally, I was thinking of writing something that takes a scheduled full backup of each database, FTPs the backups from one server to the other once they're done, and then the new server picks it up and restores it. The only downside I can see to this is that there's no way to know that the backups are done before starting to transfer them - can these backups be done synchronously? Also, the server being refreshes is our test server, so if there's some downtime involved in moving the data, that's fine. Does anybody out there have a better idea, or is what I'm currently considering the best non-replication way to go? Thanks for your help, everybody. UPDATE: I ended up designing a custom solution to get this done using BAT files, 7Zip,command line FTP, and OSQL, so it runs in a completely automatic way and aggregates the data from a dozen servers across the country. I've detailed the steps in a blog entry. Thanks for all your input!

  Read the article

• Authentification-None for one folder(page) when the project is under FormsAuthentifications

  - by Sirius Lampochkin

  I have a WebApplication on asp.net 2.0 with namespace Admin. I have Form Authentification mode for the project. <authentication mode="Forms"> <forms name="ASP_XML_Form" loginUrl="Login.aspx" protection="All" timeout="30" path="/" requireSSL="false" slidingExpiration="true" cookieless="AutoDetect"> </forms> </authentication> Now, I try to share one folder (one inside page) for not Authentificatied users: <location path="Recovery"> <system.web> <roleManager enabled="false" > </roleManager> <authentication mode="None"> </authentication> <authorization> <allow users="*" /> </authorization> <httpHandlers> <remove verb="GET" path="image.aspx" /> <remove verb="GET" path="css.aspx" /> </httpHandlers> </system.web> </location> But when I create the page inside the shared folder, it can't get access to the assembly. And I see the error like this: Could not load file or assembly 'Admin' or one of its dependencies. The system cannot find the file specified. It also shows me the error: ASP.NET runtime error: It is an error to use a section registered as allowDefinition='MachineToApplication' beyond application level. This error can be caused by a virtual directory not being configured as an application in IIS. Does anybody know how to share (Authentification None) one folder(page) when the project is under FormsAuthentifications?

  Read the article

• jquery - problem with executing annimation of two separate objects, one after another

  - by MoreThanChaos

  Hello I have problem to put together animations of two separate objects to second one start when first one ends. I tried to use callback but it seems that i make some syntax misteakes which crash jQuery or cause some unexpected behaviour. It seems that i'm stuck so I'd like to ask You for best way to put these animations together to act the way I want. in mouseenter 1st .pp grows, 2nd .tt fade in in mouseleave 1st .tt fade out, 2nd .pp shrink It's alsp relevant that animations doesn't pile up, i mean here animation called by one event doesnt wait until other animation in progress will end. In generall exactly what is below but yo be animated one after another, not simultanously. $('.pp').bind({ mouseenter: function() { $(this).animate({ width: $(this).children(".tt").outerWidth(), height: $(this).children(".tt").outerHeight() },{duration:1000,queue:false} ); $(this).children(".tt").animate({ opacity: 1.0 }, {duration:1000,queue:false}); }, mouseleave: function() { $(this).children(".tt").animate({ opacity: 0 }, {duration:1000,queue:false}); $(this).animate({ width: 17, height: 17 }, {duration:1000,queue:false}); } });

  Read the article

• [Database] How to model this one-to-one relation?

  - by pbean

  I have several entities which respresent different types of users who need to be able to log in to a particular system. Additionally, they have different types of information associated with them. For example: a "general user", which has an e-mail address and "admin user", which has a workstation number (note that this a hypothetical case). Both entities also share common properties like first name, surname, address and telephone number. Finally, they naturally need to have a (unique) user name and a password to log in. In the application, the user just has to fill in his user name and password, and the functionality of the application changes slightly according to the type of the user. You can imagine that the username needs to be unique for this work. How should I model this effectively? I can't just create two tables, because then I can't force a unique constaint on the user name. I also can't put them all in just one table, because they have different types of specific information associated to them. I think I might need 3 seperate tables, one for "users" (with user name and password), one for the "general users" and another one for the "admin users", but how would the relations between these work? Or is there another solution? (By the way, the target DBMS is MySQL, so I don't think generalization is supported in the database system itself).

  Read the article

• ColdFusion Session issue - multiple users behind one proxy IP -- cftoken and cfid seems to be shared

  - by smoothoperator

  Hi Everyone, I have an application that uses coldfusion's session management (instead of the J2EE) session management. We have one client, who has recently switched their company's traffic to us to come viaa proxy server in their network. So, to our Coldfusion server, it appears that all traffic is coming from this one IP Address, for all of the accounts of this one company.. Of the session variables, Part 1 is kept in a cflock, and Part 2 is kept in editable session variables. I may be misundestanding, but we have done it this way as we modify some values as needed throughout the application's usage. We are now running into an issue of this client having their session variables mixed up (?). We have one case where we set a timestamp.. and when it comes time to look it up, it's empty. From the looks of it this is happening because of another user on the same token. My initial thoughts are to look into modifying our existing session management to somehow generate a unique cftoken/cfid, or to start using jsession_ID, if this solves the problem at all. I have done some basic research on this issue and couldn't find anything similar, so I thought I'd ask here. Thanks!

  Read the article

• In an Android application, should I have one content provider per table or only one for the entire a

  - by Andrew Dyer

  I have years of experience with Microsoft .NET development (primarily C#) and have been working to come up to speed on Android and Java. So far, I've built a small application with a couple screens and a working content provider. All of the examples I've seen for developing content providers typically work with a single table, so I got the impression that this was the convention. I built a couple more content providers for other tables and ran into the "Unknown URI" IllegalArgumentException when I tried to test them. The exception is being thrown by one of my content providers, but not the one I was intending to call. It appears that my application is using the first content provider in the AndroidManifest.xml file, which now has me wondering if I should only have a single content provider for the entire application. Are there any best practices and/or examples for working with multiple tables in an Android application? Should I have one content provider per table or only one for the entire application? If the former, how do I resolve URIs to the proper provider? If the latter, how do I keep my content provider code from being polluted with switch statements?

  Read the article

• Dictionaries with more than one key per value in Python

  - by nickname

  I am attempting to create a nice interface to access a data set where each value has several possible keys. For example, suppose that I have both a number and a name for each value in the data set. I want to be able to access each value using either the number OR the name. I have considered several possible implementations: Using two separate dictionaries, one for the data values organized by number, and one for the data values organized by name. Simply assigning two keys to the same value in a dictionary. Creating dictionaries mapping each name to the corresponding number, and vice versa Attempting to create a hash function that maps each name to a number, etc. (related to the above) Creating an object to encapsulate all three pieces of data, then using one key to map dictionary keys to the objects and simply searching the dictionary to map the other key to the object. None of these seem ideal. The first seems ugly and unmaintainable. The second also seems fragile. The third/fourth seem plausible, but seem to require either much manual specification or an overly complex implementation. Finally, the fifth loses constant-time performance for one of the lookups. In C/C++, I believe that I would use pointers to reference the same piece of data from different keys. I know that the problem is rather similar to a database lookup problem by a non-key column, however, I would like (if possible), to maintain the approximate O(1) performance of Python dictionaries. What is the most Pythonic way to achieve this data structure?

  Read the article

• Populate JOIN into a list in one database query

  - by axio

  I am trying to get the records from the 'many' table of a one-to-many relationship and add them as a list to the relevant record from the 'one' table. I am also trying to do this in a single database request. Code derived from http://stackoverflow.com/questions/1580199/linq-to-sql-populate-join-result-into-a-list almost achieves the intended result, but makes one database request per entry in the 'one' table which is unacceptable. That failing code is here: var res = from variable in _dc.GetTable<VARIABLE>() select new { x = variable, y = variable.VARIABLE_VALUEs }; However if I do a similar query but loop through all the results, then only a single database request is made. This code achieves all goals: var res = from variable in _dc.GetTable<VARIABLE>() select variable; List<GDO.Variable> output = new List<GDO.Variable>(); foreach (var v2 in res) { List<GDO.VariableValue> values = new List<GDO.VariableValue>(); foreach (var vv in v2.VARIABLE_VALUEs) { values.Add(VariableValue.EntityToGDO(vv)); } output.Add(EntityToGDO(v2)); output[output.Count - 1].VariableValues = values; } However the latter code is ugly as hell, and it really feels like something that should be do-able in a single linq query. So, how can this be done in a single linq query that makes only a single database query? In both cases the table is set to preload using the following code: _dc = _db.CreateLinqDataContext(); var loadOptions = new DataLoadOptions(); loadOptions.LoadWith<VARIABLE>(v => v.VARIABLE_VALUEs); _dc.LoadOptions = loadOptions; I am using .NET 3.5, and the database back-end was generated using SqlMetal.

  Read the article

• JDO architecture: One to many relationship and cascading deleting

  - by user361897

  I’m new to object oriented database designs and I’m trying to understand how I should be structuring my classes in JDO for google app engine, particularly one to many relationships. Let’s say I’m building a structure for a department store where there are many departments, and each department has many products. So I’d want to have a class called Department, with a variable that is a list of a Product class. @PersistenceCapable public class Department { @PrimaryKey @Persistent(valueStrategy = IdGeneratorStrategy.IDENTITY) private String deptID; @Persistent private String departmentName; @Persistent private List<Product>; } @PersistenceCapable public class Product { @PrimaryKey @Persistent(valueStrategy = IdGeneratorStrategy.IDENTITY) private String productID; @Persistent private String productName; } But one Product can be in more than one Department (like a battery could be in electronics and household supplies). So the next question is, how do I not duplicate data in the OOD world and have only one copy of product data in numerous departments? And the next question is, let’s say I delete out a particular product, how do each of the departments know it was deleted?

  Read the article

• Git + SoA, one repo or many?

  - by parsenome

  Normally, when I start up a new application, I'd create a new git repository for it. That's well accepted and plays nice with Github when I want to share my code. At work, I'm working in a service oriented architecture. One very common pattern is to add some code to two different applications at the same time - perhaps adding a model with a RESTful interface to one and a web frontend for managing it on another. Using separate git repositories has some warts in this case. Here are what I see as the downsides of doing separate repositories: I have to commit twice I can't correllate related commits very well No single place to go back and trace history - I'd love to be able to bring up all my commits for the day in a single place Forgetting to pull one repo or another is a gotcha On the other hand, I've used perforce a lot and its one giant repository model has lots of warts too. Perforce has features designed to let help you with those, git doesn't. Has anyone else run into this situation? How did you handle it? What worked well, and what didn't?

  Read the article

• Multiple collections tied to one base collection with filters and eventing

  - by damienc88

  I have a complex model served from my back end, which has a bunch of regular attributes, some nested models, and a couple of collections. My page has two tables, one for invalid items, and one for valid items. The items in question are from one of the nested collections. Let's call it baseModel.documentCollection, implementing DocumentsCollection. I don't want any filtration code in my Marionette.CompositeViews, so what I've done is the following (note, duplicated for the 'valid' case): var invalidDocsCollection = new DocumentsCollection( baseModel.documentCollection.filter(function(item) { return !item.isValidItem(); }) ); var invalidTableView = new BookIn.PendingBookInRequestItemsCollectionView({ collection: app.collections.invalidDocsCollection }); layout.invalidDocsRegion.show(invalidTableView); This is fine for actually populating two tables independently, from one base collection. But I'm not getting the whole event pipeline down to the base collection, obviously. This means when a document's validity is changed, there's no neat way of it shifting to the other collection, therefore the other view. What I'm after is a nice way of having a base collection that I can have filter collections sit on top of. Any suggestions?

  Read the article

• Which MAC address is the right one?

  - by Paul Dinh

  Result by 'getmac': C:\>getmac Physical Address Transport Name =================== ========================================================== 72-03-C6-48-59-34 \Device\Tcpip_{8AEB3263-18C4-449E-A80F-BC2541DDC2A9} 00-21-9B-D5-6F-EE \Device\Tcpip_{C2F9CE19-D68F-4105-9766-45CBE6D82331} 00-22-68-D2-9B-F7 \Device\Tcpip_{A2701130-9221-43FE-8F14-7B1114F84DC3} Result by 'ipconfig /all': C:\>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : xps-m1530 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Mixed IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Dell Wireless 1395 WLAN Mini-Card Physical Address. . . . . . . . . : 00-22-68-D2-9B-F7 Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Autoconfiguration IP Address. . . : 169.254.246.4 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Marvell Yukon 88E8040 PCI-E Fast Eth ernet Controller Physical Address. . . . . . . . . : 00-21-9B-D5-6F-EE Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.112 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 8.8.8.8 8.8.4.4 Lease Obtained. . . . . . . . . . : 01 November 2012 9:00:36 AM Lease Expires . . . . . . . . . . : 04 November 2012 9:00:36 AM There is a MAC address on the back of my laptop, but the sticker is no longer there. So I use the 'getmac' command to get the MAC addresses. But which address shown by 'getmac' above is the one matching the MAC in the sticker on the back of my laptop? Or am I mistaken something? 00-21-... is the ethernet adapter, 00-22-... is the wireless adapter, and 72-03-... is what?

  Read the article

• CakePHP: 2-level JOIN with one Query

  - by Daniel Magliola

  I have the following models in CakePHP: A Deposit belongs to an Account An Account belongs to a Customer I want to have a list of Deposits, and I need to show the name of the customer (so I have to join through the Customer). I also need to paginate this list. If I set Deposit->recursive = 2, I can get the Customer, however, CakePHP runs one query joining Deposit and Account, and then runs one query per each Deposit, to get the Customer. How can I make it get both models with only one query? I tried this, but it didn't work: $this->paginate = array('joins' => array( array( 'table' => 'customers', 'alias' => 'AccountCustomer', 'type' => 'inner', 'foreignKey' => false, 'conditions' => array('Account.customer_id = AccountCustomer.id') ) )); Any ideas? Thanks! Daniel

  Read the article

• copy or move a file from one ftp server to another

  - by Oleg Pavliv

  I have a java application, which copies or moves a bunch of giga files from one ftp server to another. Currently it copies a file from the first fpt server to the local computer (where it runs) using ftp get and then copies it to the second ftp server using ftp put. I use net library from apache. Is it possible to copy it directly from one ftp server to another bypassing the local computer? One idea is to create a java telnet session and and send a couple of ftp commands. Will it work? Any other suggestions?

  Read the article

• Should strongly typed partial views on one page in asp.net mvc-2 have one combined view model?

  - by Kai

  Hi guys, I have a question about asp.net mvc-2 strongly typed partial views, and view models. I was just wondering if I can (or should) have two strongly typed partial views on one page, without implementing a whole new view model for that page. For example, I have a page that displays profiles, but also has an inline form to add a quick contact. Each of these entities already has it's own view model, i.e I have a ProfileViewModel and a ContactViewModel. So my view needs two strongly typed partial views, one using an IEnumerable List of ProfileViewModels, and one using a ContactViewModel. Is it possible or desirable to avoid making a third view model, an 'IndexViewModel' for this page, which holds a list of ProfileViewModels and a ContactViewModel? Is not implementing this view model bad practice, or tidier as it results in less view models? Thanks!

  Read the article

< Previous Page | 59 60 61 62 63 64 65 66 67 68 69 70  | Next Page >