Search Results

Search found 4701 results on 189 pages for 'ram moj'.

Page 63/189 | < Previous Page | 59 60 61 62 63 64 65 66 67 68 69 70  | Next Page >

  • Upgrading memory in a laptop

    - by ulidtko
    I'm a bit confused about all the memory types and various bus frequencies of modern consumer PCs. Requesting expert help on the subject. So far I'm confident that: I have an Asus X51L laptop with an unknown set of configuration options. The CPU in there supports PAE, so I still have a chance to extend the memory beyond 3GiB; and the upper limit of the system is 8GiB. (?) The laptop has two SODIMM slots, one of which is occupied by a 2GiB bank, and the other one is empty. dmidecode and lshw tools consistently state 533 Mhz frequency of the bank. The last one confuses me the most. I failed to find out characteristics of the northbridge in this laptop, and still can't figure out what DDR2 to seek for. Is it DDR2-1066? Or, rather, PC2-8500/PC2-8600? Wouldn't a DDR2-800 bank harm the system's performance? Which kind of modules should I look up in stores? Update: I have bought a 2 GiB DDR2-800 SODIMM, and it seams that the system can't handle 4 GiB of memory. When installed by itself in either slot, both new and old bank (which btw happens to be marked GDDR2-677) work just perfectly; i.e. any configuration resulting in 2 GiB works. When both banks are installed though (totalling in 4 GiB), the memcheck86 tool produces horrible artifacts and crashes, and system reboots; an Ubuntu system can be started and even logged into a Unity session, but the system reboots too in this case from even a minor RAM load. So it's pretty obvious to me now that this laptop doesn't support 4 GiB of RAM or more.

    Read the article

  • SSD for swap on Ubuntu server

    - by grs
    Currently I am reading SSD reviews and I wonder how much exactly I will benefit if I move the 24 GB swap from 7200rpm HDD to SSD. Does anyone implemented swap space on SSD? Is this generally good idea? On a side note: I read that ext4 has much better performance if the journal is on SSD. Anyone with such a setup? Thanks! Edit: Here I will answer the questions posted: Occasionally, relatively rare I am hitting the swap. I know what the swap is for and that is better to get more RAM. When the server begins to swap its performance degrades (not a surprise). The idea is if I have few memory hungry processes running, to improve the overall system performance at that time, using SSD for swap, instead of slower rotational media. At the end - I want to be able to login faster and check the server state during swapping, instead of waiting on the login prompt. And of what I see SSD is cheaper per GB than RAM. Would I have better server performance during swapping (as rare it is) using SSD compared to HDD? Where 10k or 15k rpm HDDs would rate in this scenario? Thank you all for your quick and prompt answers!

    Read the article

  • Recovering ZFS pool with errors on import.

    - by Sqeaky
    I have a machine that had some trouble with some bad RAM. After I diagnosed it and removed the offending stick of RAM, The ZFS pool in the machine was trying to access drives by using incorrect device names. I simply exported the pool and re-imported it to correct this. However I am now getting this error. The pool Storage no longer automatically mounts sqeaky@sqeaky-media-server:/$ sudo zpool status no pools available A regular import says its corrupt sqeaky@sqeaky-media-server:/$ sudo zpool import pool: Storage id: 13247750448079582452 state: UNAVAIL status: The pool is formatted using an older on-disk version. action: The pool cannot be imported due to damaged devices or data. config: Storage UNAVAIL insufficient replicas raidz1 UNAVAIL corrupted data 805066522130738790 ONLINE sdd3 ONLINE sda3 ONLINE sdc ONLINE A specific import says the vdev configuration is invalid sqeaky@sqeaky-media-server:/$ sudo zpool import Storage cannot import 'Storage': invalid vdev configuration I should have 4 devices in my ZFS pool: /dev/sda3 /dev/sdd3 /dev/sdc /dev/sdb I have no clue what 805066522130738790 is but I plan on investigating further. I am also trying to figure out how to use zdb to get more information about what the pool thinks is going on. For reference This was setup this way, because at the time this machine/pool was setup it needed certain Linux features and booting from ZFS wasn't yet supported in Linux. The partitions sda1 and sdd1 are in a raid 1 for the operating system and sdd2 and sda2 are in a raid1 for the swap. Any clue on how to recover this ZFS pool?

    Read the article

  • EC2 AMI won't boot after edit

    - by Eric Lars0n
    I did something stupid, I got a new laptop and copied everything over to the new one, then wiped the old one clean. Then I realized that I forgot to copy the private key out of .ssh that I use to connect to my AWS EBS backed instance. So I can't log in to my custom AMI. So I created a new Volume from the Snapshot of the AMI, then started up a public instance and attached the Volume to it, edit the sshd_config to allow for password log in. Unmounted the volume, detached it, made a snapshot of it, then made a new AMI from the snapshot. The new AMI launches, but never passes the Status Checks and is not reachable. What am I doing wrong? Or alternatively how can I fix my problem? Edit: Adding some of the console output Linux version 2.6.16-xenU ([email protected]) (gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 SMP Mon May 28 03:41:49 SAST 2007 BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000006a400000 (usable) 980MB HIGHMEM available. 727MB LOWMEM available. NX (Execute Disable) protection: active IRQ lockup detection disabled RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize NET: Registered protocol family 2 Registering block device major 8 XENBUS: Timeout connecting to devices! Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,0)

    Read the article

  • Memory overcommitment on VmWare ESXi 5.0

    - by Tibor
    I would like to understand better the possibilities of VmWare ESXi memory overcommitment. I've read this paper from VmWare, so I am familiar with general concepts, such as hypervisor swapping, memory balooning and page sharing. It seems that a combination of these techniques allows for quite a large degree of overcommitment. However, I am not sure. I am deploying a virtual test lab comprising of 4 identical sets of virtual servers and workstations and a couple of virtual router instances. Overall, I expect to be running around 20 virtual machines with Windows XP, Windows 7 and Ubuntu for workstation hosts as well as CentOS and Windows 2008 Server instances for servers. The problem is, however, that the host machine only has 12GB of RAM and I don't have an option to stuff in some more. I would like to know what is the best option to configure hosts in order to achieve reasonable performance within the constrains. I have these two options: Allocate as little as possible of RAM to each virtual machine. Allocate an extraordinary amount (such as 4 GB per instance) and let the baloon driver do the rest. Something else? Which would work better? Machines will mostly be idle, so I don't have any major performance expectations, but they should run reasonably smoothly nevertheless.

    Read the article

  • What kind of hosting do I need? [closed]

    - by Robert Smith
    I have been trying to answer this question but I haven't found an specific answer to my situation. As I want to pay for what I need, I thought I could get a good answer here. I have custom made forum (rather than a built-in forum like the ones you can find as plugins, e.g. WP-Forum or phpBB type of software) in Django. I don't want to use Apache and modwsgi because it's usually very memory-hungry and I can't afford a big server. I prefer a combination of nginx and gunicorn which I think is very efficient (maybe you can also tell me what you think about that). I'm expecting to receive 10,000 to 20,000 visits each month with 15,000 to 30,000 page impressions. I have reviewed some cloud services like Amazon EC2 or Rackspace and other more traditional services (Linodo). This site won't use videos or big images and I certainly don't need a huge amount of bandwidth (200GB would be definitely too much). I need shell access so shared hosting is out of the question. What do I need to run a website like that without problems? What about RAM? 256MB would be enough (that's the amount of RAM offered by small instances in Amazon and Rackspace)? Do you know of any alternative to those I mentioned? If you need more information to provide a useful answer, please don't hesitate to ask. Thanks a lot.

    Read the article

  • Configuring Vmware virtual machines to run under different IPs and PC specs

    - by Alex
    Right now I'm using a simple VmWare virtual machine with preinstalled Win 7. The IP is assigned automatically (it's the same as main OS IP). Is it possible to create several virtual machines that have different hardware specifications and different IP addresses? Here is what I mean regarding these issues: Specs: Certainly, you can easily change some specifications in the Settings menu (RAM size, HDD size), but what about advanced settings? For example: advanced settings for the Processor: is it AMD (2500+,4000+, etc.. ) or Intel (core 2, Pentium, etc..) Ram - is it Corsair 4 Gb 1333 Mhz or Kingston 2 x 2 Gb 866Mhz or something else? Hdd - Is it Seagate Barracuda 80 gb 5400 Rpm or is it Samsung 500Gb 7200 Rpm or some random SSD? Programs that work under a Virtual Machine shouldn't have a clue if that's a VmWare or not. IPs: Every program that's launched under main OS use the real IP: 93.56.xx.xx All programs that are launched under virtual machine A use IP 1: 74.78.xx.xx All programs that are launched under virtual machine B use IP 2: 84.159.xx.xx I believe that you have to use either VPN or Proxy to solve this problem. The Sum Up: The idea is to create 2-3 independent virtual machines with different hardware specifications and IP addresses. Programs that work under a certain Virtual Machine shouldn't have a clue if that's a VmWare or the real PC. Any ideas/tips or experience regarding configuration will be appreciated!

    Read the article

  • How To Boot with "mem=1024m" Argument using GRUB - Ubuntu 10.04

    - by nicorellius
    I am still working on this question. This new one is a different question so I thought it would be good to post a new question. Is this the proper protocol or should I have just edited the other question? I'm running Ubuntu 10.04 with the kernel 2.6.32-22-generic on a Toshiba Satellite laptop. When I enter the GRUB menu (I have Ubuntu 9.10 installed as well), I can choose which kernel to boot. I use scroll down to the one I want and press "e" and I expect to be able to enter mem=1024m and force the kernel to use this much memory. But when I run cat /proc/meminfo or look in the process manager after booting wth this argument I still see all the RAM: ~2 GB. Am I using this boot argument incorrectly? The boot configuration (before I add anything) looks like this: insmod ext2 set root=(hd0,1) search --no-floppy --fs-uuid --set 10270f21-1c42-494b-bd3f-813c23f6d\ 518 linux /boot/vmlinuz-2.6.32-22-generic root=UUID=10270f21-1c42-494b-b\ d3f-813c23f6d518 ro quiet splash initrd /boot/initrd.img-2.6.32-22-generic The way I did this was that I added the mem=1024m after the last line and pressed Ctrl+x (Emacs save and boot the kernel) and the system booted. I tried adding mem=1024m to the end and the beginning of this list and it appeared to not change the RAM allocation.

    Read the article

  • Google Chrome is running my system out of memory

    - by jasondavis
    I am running Windows 7 x64 with 12GB of RAM I often have multiple windows and a ton of tabs open. I use the extension Session Buddy to restore all my windows and tabs once the memory gets too high. So my 12gb of ram will get up to around 93% used because of Chrome, now I can close chrome down and restore the same amount of windows and tabs and it will only use about 25% of memory, it then over time increases back up to the 90% zone after several hours. It seems that when I close tabs, instead of freeing that memory up, it doesn't so that is why the huge increase of memory usage as new tabs are opened and closed it just adds up, this sounds like a huge bug in chrome. Just for an example I just re-booted my system, I only have 1 window with 4 tabs open and in the task manager, it shows 29 chrome.exe processes I then killed all chrome processes and opened a chrome window with just 1 tab, it made 27 chrome.exe processes. Is this an issue that others have? More importantly, is there a fix? UPDATE I just read that each plugin and extension creates a chrome.exe process, I then couunted 24 extensions so that helps explain a portion of the large processes. Still not sure about memory not being freed up though!

    Read the article

  • Gaming blew fuse: how to overcome?

    - by George Tomlinson
    I've been gaming for a while now. When playing certain games this PC goes into overdrive. The fan/fans start/s to sound like a jet engine it/they get/s so busy. Also I have smelt burning when this has happened. The fuse blew on the 4 socket adapter I was using recently. On the following thread someone said this could be due to the PSU not being strong enough to handle the load, in what it seems could be a related issue someone had, although the person who posted this question did say that blowing a fan on their PC stopped it crashing in that case: http://www.tomshardware.co.uk/answers/id-2047543/gtx-650-overheating-issue.html. This is exactly what they said: Your GPU isn't overheating. 70+ before it would shutdown and cause a restart. Make sure your PSU is strong enough to handle your new system at load and possibly run Memtest to check your RAM (although not BSOD'ing and just shutting down points to the PSU). This (the PSU part) makes more sense to me than it being to do with dust etc, since it seems a more plausible explanation of why the fuse blew. The PC has no problems except when playing certain games: i.e. TERA Rising and WoW with add-ons (I think WoW is ok as long as I don't have more than 1 add-on (Healers Have To Die)). I'm just wondering if anyone knows or can suggest what I might be able to do to be able to play these games without this problem occurring. The PC's spec is this: Display: NVIDIA GeForce GTX 650 8GB RAM (6 available) Processor: AMD FX (tm) - 8120 Eight-Core Processor - 3.1 GHz, 4 Cores, 8 Logical Processors I have read on another post that forcing vsync in the Nvidia Control Panel helped with what seems could be a similar problem, so I plan to see if that solves it, God permitting.

    Read the article

  • Upgrade to Q9550 or i7 920 on a budget?

    - by evan
    I'm planning to upgrade my computer and torn between maxing out the system I have or investing in the X58 architecture. I'm currently using a E6600 Core 2 Duo with 4GB of RAM (800mhz) on an Asus PK5-E motherboard which I built two years ago. My original plan was that one day I'd upgrade machine to 8GB (1066mhz, the max the PK5-E allows) and to the Core 2 QuadQ9550 to give the machine a good four years of life. However, that was before the i7 came out. I use my computer mainly for software development , which I do inside Virtual Machines, and the i7 seems ideal for that because it no longer is limited by the speed of the FSB? And when I looked into it, getting 8GB DDR3 RAM isn't much more expensive than the 8GB of DDR2 and the i7 920 is comparable in price to the Q9550, which doesn't make much sense to me? So the question is it worth swapping the motherboard out for around $250 and upgrading all three components or using that money on SSD or 10rpm drive for the existing system's OS/Apps/Virtual Machine drive? Or just put the $250 towards a completely new machine in a year or two? Would the i7 really give that much of boost compared to the Q9550 for what I'd be using it for? Thanks in advance for your input!!!

    Read the article

  • CPU not working on a specific motherboard

    - by Shaman
    I'm making a computer for someone and I met a weird problem. The CPU that I have doesn't work on this motherboard. The CPU is an Intel Pentium D 925 and the motherboard is an ECS G41T-M6, which in theory should work together. The only thing reused is the power source(400W). When I start the computer, the fans start, and that's it. The BIOS doesn't boot. I tried my own power source (600W Corsair) and nothing. Removed the RAM, no warning. In desperation I tried the last thing, swaped my own CPU with this one (Core2Duo E7200). Lo and behold, it worked. Both. The Core2Duo worked on the ECS with the old power source and the RAM that I used in the first place, and the Pentium D worked on my Gigabyte G31M-ES2L. What I discovered was that the Pentium D didn't receive power on the ECS, because I tried running it without the cooler and it remained at room temperature. On a side note, I also removed the HDDs just in case. So, in conclusion, any ideas? I can't return it, and I can still use it to upgrade another PC, but I would really prefer not to buy another CPU if possible.

    Read the article

  • Proper approach to debug PC startup problems (POST)

    - by saurabhj
    My CPU was heating up to around 65 deg C and last time this had happened (about a year ago), I got thermal paste put between the CPU and heat sink and this managed to get it down to about 45 - 50 degrees. This time, I got some thermal paste and put it myself. However, my PC is not showing the POST display and not starting up. This is what happens LEDs light up HDDs spin Mouse is getting power All fans including the processor fan starts No display on monitor No diagnostic beep sounds (no sounds at all) What I have tried Removing everything including RAM, HDD, PCI cards, AGP card Boot up machine No changes from first state. What steps can I take to figure out where the problem lies? Note (might be important) When I removed the heat sink, the processor came out with it (it was stuck to it inspite of the processor latch on) Had to pry it separate with a screw-driver. Configuration Pentium 4, 2.8 Ghz with HT (very old, I know) Original Intel Mobo with onboard sound and graphics (GB series) 2x512 Mb DDR-RAM 2 SATA disks (320 Gigs / 250 gigs) DVD Writer Creative Sound Card Network card Any help would be appreciated. Thanks!

    Read the article

  • At what point does the performance gap between GPU & CPU become so great that the CPU is holding back a system?

    - by Matthew Galloway
    I know that generally speaking for gaming performance the GPU is the primary factor which holds back performance, with everything else such as RAM/motherboard/PSU/CPU being secondary in importance to the graphics card. But at some point the other components ARE going to be significant in holding back the whole system! For instance nobody would be silly enough to play modern games with 512MB RAM and the very latest graphics cards (such as an HD7970) as I bet the performance increase over such a system with only 512MB but a mid range card would be non-existent! Thus it would be a "waste" for such a person to buy any high end graphics card without resolving first the system's other problems. The same point applies to other components, such as if it only had a Pentium II a current high end graphics card would be wasted on it! So my core question is how do you determine at what point for your system is spending on extra GPU power be completely "wasted"? (also, a slightly more nuanced question is trying work out at what point might the extra graphics power not be "wasted" but would be "sub optimal" value for money, when the expenditure should then be split around graphics card and other components. As obviously a gamer shouldn't always just spend on upgrading the graphics card! But needs to balance it out)

    Read the article

  • Ubuntu inside VirtualBox is slow

    - by Kapsh
    I am running an Ubuntu instance on VirtualBox inside XP. Here are the details: Host: Windows XP Pro Guest: Ubuntu 8.10 Total RAM: 3GB RAM For VM: 1GB Total Video Memory: 128MB Video Memory for VM: 40MB Hard Drive: 200GB Hard Drive for VM: 30GB Processor: 2.80GHz Core Duo The problem is that whenever I am inside the virtual machine, things seem so much slower in general. For example Firefox, Eclipse take longer to load, dragging windows show a lag etc. I have tried running Ubuntu before (not inside a VM) and it seemed fantastically fast. So I am disappointed to have to deal with this situation. But I need access to the XP partition without having to reboot and hence the attempt. I am surprised with the perceived slowness since the whole world seems to be doing virtualization and I cannot imagine everyone works on slow systems knowingly. My question is - is there something I should be doing to boost performance? Am I doing something wrong? This is my home machine and I am not sure if this is the right forum to ask. Thanks.

    Read the article

  • What is the max connections via remote desktop for a small server?

    - by Jay Wen
    I have a small server running MS Server 2012. The CPU is a Xeon E3-1230 V2 @ 3.30GHz, 4 Cores, 8 Logical Processors, 8 GB RAM. Main HD is a Samsung 840, and the big storage is a 4 disk WD Black Raid 10 Array in a Synology NAS enclusure. My question is: given this hardware, approximately how many users can the system support via "Remote Desktop Connection"? Assume there are no licensing limits. These are not admin users. I know there is a two admin limit. This boils down to: What resources does one remote connection require? RAM? % of the CPU? Networking bandwidth? I guess the base case would be for a conection where the user is inactive or simply browsing cnn. Once you know this, you know how many you could fit on the machine before something is maxed-out. In reality, users would be mostly on Excel (multi-MB spreadsheets). I know the approx. resources currently required by each copy of Excel.

    Read the article

  • centos install / partitioning

    - by ServerSideX
    I'm using NOC-PS to remotely install Centos 6.2 via KVM / IPMI. I'm going to install cPanel as well and they recommend this layout /boot (99MB) swap (2x server RAM) / (remainder) In the o/s install profile within NOC-PS software, it shows as this: part /boot --fstype ext2 --size 250 part pv.01 --size 1 --grow volgroup vg pv.01 logvol / --vgname=vg --size=1 --grow --fstype ext4 --fsoptions=discard,noatime --name=root logvol /tmp --vgname=vg --size=1024 --fstype ext4 --fsoptions=discard,noatime --name=tmp logvol swap --vgname=vg --recommended --name=swap By the time the default partition setup was done installing Centos, I get this [root@server005 ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg-root 532G 907M 504G 1% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 243M 28M 202M 13% /boot /dev/mapper/vg-tmp 1008M 34M 924M 4% /tmp [root@server005 ~]# cat /etc/fstab # # /etc/fstab # Created by anaconda on Fri Dec 7 18:47:24 2012 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # /dev/mapper/vg-root / ext4 discard,noatime 1 1 UUID=58b31aaf-5072-4fb1-a858-33bc316fa793 /boot ext2 defaults 1 2 /dev/mapper/vg-tmp /tmp ext4 discard,noatime 1 2 /dev/mapper/vg-swap swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 My question is, how should the NOC-PS install profile look like to get the recommended cPanel partitioning? The server has 16GB RAM, dual 600GB SAS drives and will be used for cPanel shared hosting.

    Read the article

  • Linux iptables / conntrack performance issue

    - by tim
    I have a test-setup in the lab with 4 machines: 2 old P4 machines (t1, t2) 1 Xeon 5420 DP 2.5 GHz 8 GB RAM (t3) Intel e1000 1 Xeon 5420 DP 2.5 GHz 8 GB RAM (t4) Intel e1000 to test linux firewall performance since we got bitten by a number of syn-flood attacks in the last months. All machines run Ubuntu 12.04 64bit. t1, t2, t3 are interconnected through an 1GB/s switch, t4 is connected to t3 via an extra interface. So t3 simulates the firewall, t4 is the target, t1,t2 play the attackers generating a packetstorm thorugh (192.168.4.199 is t4): hping3 -I eth1 --rand-source --syn --flood 192.168.4.199 -p 80 t4 drops all incoming packets to avoid confusion with gateways, performance issues of t4 etc. I watch the packet stats in iptraf. I have configured the firewall (t3) as follows: stock 3.2.0-31-generic #50-Ubuntu SMP kernel rhash_entries=33554432 as kernel parameter sysctl as follows: net.ipv4.ip_forward = 1 net.ipv4.route.gc_elasticity = 2 net.ipv4.route.gc_timeout = 1 net.ipv4.route.gc_interval = 5 net.ipv4.route.gc_min_interval_ms = 500 net.ipv4.route.gc_thresh = 2000000 net.ipv4.route.max_size = 20000000 (I have tweaked a lot to keep t3 running when t1+t2 are sending as many packets as possible). The result of this efforts are somewhat odd: t1+t2 manage to send each about 200k packets/s. t4 in the best case sees aroung 200k in total so half of the packets are lost. t3 is nearly unusable on console though packets are flowing through it (high numbers of soft-irqs) the route cache garbage collector is no way near to being predictable and in the default setting overwhelmed by very few packets/s (<50k packets/s) activating stateful iptables rules makes the packet rate arriving on t4 drop to around 100k packets/s, efectively losing more than 75% of the packets And this - here is my main concern - with two old P4 machines sending as many packets as they can - which means nearly everyone on the net should be capable of this. So here goes my question: Did I overlook some importand point in the config or in my test setup? Are there any alternatives for building firewall system especially on smp systems?

    Read the article

  • PXELinux and compressed kernels/images

    - by Yvan JANSSENS
    Is it possible to boot compressed kernels with a compressed initrd with PXELinux? First, a little background: We created a custom Linux distro, for diskless OpenCL computing nodes. We want those nodes to fetch their OS from the network. Our Distro is composed out of a kernel (duh) and a large initrd which is loaded into RAM and everything is executed from there. We chose to run everything off the initrd for two reasons: NFS was not an option to serve the filesystem's extra contents Fast file access from RAM. No persistent storage needed, data and config is pulled dynamically through a SOAP service. Now our initrd is about 450M in size. At our network speeds, it takes about two to three minutes to load a single client. Will compression speed up te downloading, and if yes, which one should be used? Is LZMA supported by PXELinux, or do we need to stick to bzip2 or gzip? Because of the 2-3 minutes loading time, booting 15 nodes over the same network link takes quite a lot of time. We decided not to use hard drives or CD/DVD drives, for financial reasons (cheapest HDD @ €30 times 15 is a lot of money saved ;-) ) So, our question is: what compression options are available for this setup? And how do we do this? Thank you for your time! Yvan Janssens

    Read the article

  • Why is my computer randomly restarting? How can I fix it?

    - by kinglime
    I have a custom built desktop computer that I've been using since about a year ago. The main specs are: ASUS P8Z68-V LE Motherboard Intel Core i7 2600k Corsair Vengeance 16GB Ram ASUS ENGTX570 GPU Corsair TX650M PSU I was running an overclock of 4.4ghz for my cpu (I have a Hyper212 EVO) and 1600mhz for my RAM but have it currently turned off due to my issues. I am also currently running Windows 8 but this problem occured in Windows 7 too. Basically my issue is that seemingly randomly, with no pattern my PC will reset itself and ASUS Anti-Surge will alert me that something went wrong. This issue is not related to system stress. I can run it fine for an hour maxxed out on Prime95 then later I can be watching a mere YouTube video when it will randomly reset. This has been occurring probably for the last two weeks and it seems to be getting worse. I believe this might be related to the power supply but when I monitor it in the bios and in Windows it appears to be putting out the proper voltages. Also possibly related or not but my Nvidia drivers frequently temporarily fail and then warn me of some kind of kernel error? If I have to buy a new power supply that is what I'll do but I want to make damn sure that's the only issue at hand. Thank you everyone in advance, please help me diagnose the issue and tell me what I can do to fix it. If you need any additional info about my setup please ask me.

    Read the article

  • Hardware testing tool/suite

    - by Aviator
    Hi All, I just bought a new core i5 system (assembled) and started installing Windows 7. It was failing for many times and at some point got installed. After that, frequent crashes related to MEMORY. So checked the RAM using memtest86+ and found many errors.I got it replaced with the vendor and now if i install ANY OS, at some point in installation it either freezes completely with no response for hours, or restarts automatically. I tried installing Windows 7, Windows Vista and Ubuntu 9.10. I tested the new RAM again and found no problems in about 2 passes using memtest86+. I even updated the BIOS using bootable USB and even the problem persists. I am really not sure which hardware is causing trouble. I dont have any OS inside it, so i have to check using bootable CDs DVDs and USB only. Please advice on how to proceed. Are there any suites/ separate tools for checking integrity of each hardware parts and troubleshoot it? I wanted to confirm which part is problematic before going for replacement. Thanks a lot! This is the config: Core i5, MSI P55-GD65, GSKill 2x2GB, Seagate 500GB 7200rpm, CM Extreme 600W PSU, Saphhire Radeon 5770 1GB, LG DVD Writer

    Read the article

  • SBS 2008 Sharepoint Database good Memory Limit.

    - by ldelgado
    I manage a small network running on Small Business Server 2008. Lately, the Sharepoint embedded database is getting out of control with its memory usage. I've got a total of 16 GB of RAM on this server, and the Sharepoint database sometimes uses almost 8 GB of RAM. This never happened before, and it started happening after I installed Backup Exec 2010. It happens after a backup is performed. So I suspect there is a memory leak involved. I am working on that issue, but this question isn't about that. I would like to limit the amount of memory the Embedded database uses. I know how to do it. My question is, what would be the ideal amount of memory that I can allocate to Sharepoint? There are only 4 users on my network. One of the users uses two computers but not at the same time. They use sharepoint for a company calendar, and sometimes they share files that way also. Let me know if you need to know anything else. Thanks,

    Read the article

  • Strange boot problems on 6 month old setup

    - by Balefire
    I've already exhausted my knowledge on this one, so forgive me if this post is a bit long. I built a computer 6 months ago for my wife and it worked fine until last week. Then it randomly shut down and would lock up while trying to boot on the boot screen. I cleared cmos and it allowed me to do startup recovery, but it "failed to fix the issue" so I reinstalled windows on the HD (moving the old install to windows_old). It worked, so I started installing drivers again, but then when I restarted to finalize installations it locked up again. This time, I took the hard drive and hooked it up to my computer, backed up all her files, and then formatted the hard drive before reinstalling it. (again had to clear cmos to let me boot from disk) It installed windows, I installed drivers, and it worked for a few hours but then died during startup again. So, then I got a new HD, cleared cmos, and installed clean again, with the same result as the time before, it worked for a few hours, installed windows updates, then crashed on the 3rd or 4th time turning it on. I decided next to try reinstalling and then going online to see if there were any updates for the BIOS or drivers on the Motherboard, but now I can't get it to even bring up the boot menu, so now I'm just left wondering was it the motherboard, or is it the CPU, or the RAM? The problem was strangely intermittent so I thought it had to be a software issue, since a hardware issue would ALWAYS fail to boot, right? But now it seems to be a hardware issue, because it's not bringing up anything. Any suggestions? System: Windows 7 64-bit 970A-DS3 Gigabyte Motherboard AMD Phenom II X4 955 Deneb 3.2GHz Quad core Proc GeForce GT 430 (Fermi) 1GB Video Card 500W PSU 2 x G.SKILL Ripjaws X Series 4GB 240-Pin DDR3 1600 RAM

    Read the article

  • 3-4 old computers = general purpose cluster?

    - by TheLQ
    I have 3 old computers lying around right now running a P2 at 800 MHz(?), Intel Mobile 1.6 GHz, AMD Athlon XP 2000+ at 1.66 GHz, and (might not use this) P4 at 2.7 GHz, all with 512 MB Ram, and am considering clustering them together for fun/knowledge. They would be running an undecided version of linux, preferably ubuntu based. The issue is what I want to use it for: general computing and occasional video encoding. By general computing I mean day to day tasks. However I'm not sure if every program started by a single X session is going to exist on the same machine, defeating the purpose of such a system. Will programs be split up or exist on one machine? Second, assuming this is running 100baseT ethernet (not sure if the PCI slot itself could handle Gigabit), would the speed of having a program exist over the network be an issue? It seems that the constant asking of various things in RAM would be quite slow. And before you say "buy another computer!", that's not the point of this question. I'm asking would it be usable, not necessarily practical. And yes I know, this is going to be extreamly power consuming.

    Read the article

  • 4GB Memory Upgrade for Acer Aspire 5102WLMi

    - by Richard Slater
    I have bought a 4GB memory upgrade (2x 2GB PC2-5300 SODIMM) for my Acer Aspire 5102WLMi (Aspire 5100 Series) laptop, I installed the two memory modules correctly however with 4GB installed the laptop refuses to POST. I have tried the following: Tried both 2GB SODIMMs without the other (Worked Fine) Tried the original 512MB SODIMMs (Worked Fine) Tried with original 512MB SODIMM and new 2GB SODIMM (Worked Fine) Tried swapping over the 2GB SODIMs (Didn't Boot) Left the computer for 10 minutes with both 2GB SODIMMs installed (Didn't Boot) Checked latest BIOS installed (No Change) The Crucial website said that the laptop supported 4GB of RAM as do several other sites through found through Google, up until now I was fairly confident this would work. Couple of questions that would be good to have answered: Question: Has anyone got an Acer Aspire 5100 Series running with 4GB RAM? Answer: Yes, I have now got one working with 3.75GB Usable, the rest is occupied utilized by the Graphics Card. Question: Any tips on getting this to work; is there a CMOS reset switch? Answer: Yes there is, if both SODIMMs are removed two very small interlocking PCB tracks are revealed. If these are shorted together with a screwdriver the BIOS will be reset. Thanks.

    Read the article

< Previous Page | 59 60 61 62 63 64 65 66 67 68 69 70  | Next Page >