Search Results

Search found 22874 results on 915 pages for 'hidden network'.

Page 64/915 | < Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >

• Access points fighting for dominance?

  - by Phillip Oldham

  We have a small office with a large number of wireless devices (a mixture of desktop machines, laptops, and wifi-enabled phones) all working from a single Apple Airport Extreme which extends our wired network. I've added another Airport Extreme for resiliency, since we've been seeing a decrease in performance and (as far as I understand) access points can only handle a small number of clients. I set the new AP to extend the current network so that the clients weren't constantly switching between different wireless networks, however as soon as this AP was configured all the wireless devices started seeing network trouble, flicking on and off. I'm assuming that this is because both APs are reasonably strong, and the client can't decide which to use. What is the best route to follow to resolve this? What I'm aiming for is wireless resiliency; preferably having two APs share the network load, or if this isn't an option then having a primary AP with a "fail-over", should the primary go down for any reason.

  Read the article

• Hidden characters inserted after pipe (|) followed by a space

  - by nifty

  Very often, on my Mac, when I use the pipe (|) character followed by a space character, an invincible character will be inserted in between. This is especially annoying when using the terminal, as it makes commands invalid. If I type the following in iterm2, I often get the following: ls | cat zsh: command not found:  cat If I hit the up-arrow-key to get my previous command, and then remove and reinsert the space between | and cat, the command will work. When I copy paste the working and non working commands into a file, like this: non-working: ls | cat working: ls | cat and open it in Hex Fiend it shows the following: non-working: ls |¬†cat working: ls | cat I've also experienced the same kind of issue in SublimeText2 using the square brackets ([]) followed by a space. So I don't believe its an issue with iTerm2.

  Read the article

• How to use a home network patch panel?

  - by Torben Gundtofte-Bruun

  I'm planning a home network in a house that's not built yet. One recommendation is to add network sockets in various rooms and have them all end in a central place, where it all connects using a network switch. So far so good. Another recommendation says to not connect everything directly to the switch, but to a patch panel which in turn is connected to the switch. I'm unsure why this is good. Is there any practical advantage of using a patch panel if you're not planning to re-wire things very often? How does a patch panel actually work? Let's say it has 24 ports. Does it have another 24 ports on the backside that go to the switch, or what? Wikipedia isn't helpful on this. Clarification: I am planning to run network cables through conduits inside the walls and terminated with network sockets in the wall (as opposed to having just conduits and long regular network cables that have a normal plug in each end). Going by RedGrittyBrick's answer, a patch panel is nearly unavoidable in that case.

  Read the article

• PDF Encrypted, Hidden Watermark

  - by Dave Jarvis

  Background Using LaTeX to write a book. When a user purchases the book, the PDF will be generated automatically. Problem The PDF should have a watermark that includes the person's name and contact information. Question What software meets the following criteria: Applies encrypted, undetectable watermarks to a PDF Open Source Platform independent (Linux, Windows) Fast (marks a 200 page PDF in under 1 second) Batch processing (exclusively command-line driven) Collusion-attack resistant Non-fragile (e.g., PDF - EPS - PDF still contains the watermark) Well documented (shows example usages) Ideas & Resources Some thoughts and findings: Natural language processing (NLP) watermarks. Apply steganography on a randomly selected image. http://openstego.sourceforge.net/cmdline.html The problem with NLP is that grammatical errors can be introduced. The problem with steganography is that the images are sourced from an image cache, and so recreating that cache with watermarked images will impart a delay when generating the PDF (I could just delete one image from the cache, but that's not an elegant solution). Thank you!

  Read the article

• API Class with intensive network requests

  - by Marco Acierno

  I'm working an API which works as "intermediary" between a REST API and the developer. In this way, when the programmer do something like this: User user = client.getUser(nickname); it will execute a network request to download from the service the data about the user and then the programmer can use the data by doing things like user.getLocation(); user.getDisplayName(); and so on. Now there are some methods like getFollowers() which execute another network request and i could do it in two ways: Download all the data in the getUser method (and not only the most important) but in this way the request time could be very long since it should execute the request to various urls Download the data when the user calls the method, it looks like the best way and to improve it i could cache the result so the next call to getFollowers returns immediately with the data already download instead of execute again the request. What is the best way? And i should let methods like getUser and getFollowers stop the code execution until the data is ready or i should implement a callback so when the data is ready the callback gets fired? (this looks like Javascript)

  Read the article

• can I put files in hidden volume /home at the root level of macintosh HD

  - by mjr

  I am trying to reproduce the file structure of my VPS on my mac locally, so that it's easier for me to test websites in a local development environment to do this I would need have a /home folder at the root level of the hard drive using panic transmit I can see that there is already a volume called home at the root level can I store other files and folders in here to set up my local web server? sorry if this is a dumb question folks

  Read the article

• Word document has very strange "hidden" formating after converting from PDF to .docx

  - by Celeritas

  I have a PDF document with my resume which I need to edit. I used this service to convert it to doc. I opened it in Word 2010 and saved it as .docx. There are some bizzare problems where there's empty space and if you try to delete it text gets shifted into vertical columns. How can I fix this? I'm afraid this document has a lot of private information and I can't just fill in dummy text, then the formatting gets even more messed up :/ Otherwise I'd post screen shots.

  Read the article

• Problems with microphone and network

  - by AnoonymoouS

  Hello... very good day everybody! I'm having some problems regarding the Ubuntu 12.4.01 LTS. For this reason, cordially i ask everyone's help. Such problems can be summed up in network (01) and audio (02)! 01) I can not set a DSL network settings in the "upper bar" (on side the clock). When i create the connection, the system says that the cables modem are disconnected! I can only use the internet if i set up a connection at terminal through the command "pppoeconf". Follows the print screen of what i mentioned above:. http://i.imgur.com/8nTrF.png Obs.: Note that even after the connection "created", it does not appear there! 02) The sound is reproduced; however, can not be captured! I can not make recordings, obviously i can't use the microphone. I believe that something is giving interference or the settings are wrong! Follows the video of what i mentioned above:. http://dl.dropbox.com/u/41085750/Projeto%20Padr%C3%A3o.mp4 Obs.: I'm listening to music, so that interference errors may appear in the video. By kindness; who can help me... help me! I sought help at various sites and forums but unfortunately, i did not get success. I wait anxiously for a direction. Regards, Anoonymoous.

  Read the article

• Software vs Network Engineer (Salary, Difficulty, Learning, Happiness)

  - by B Z

  What are your thoughts on being a Software Engineer vs a Network Engineer? I've been on the software field for almost 10 years now and although I still have a great deal of fun (and challenges), I am starting to think it could be better on the "other" side. Not to degrade network engineers (i know there are many great ones out there), it seems (in general) their job is easier, the learning curve from average to good is not as steep, job is less stressful and pay is better on average. I think as software developer I could make the switch to networking and still enjoy working with computers and feel productive. I spend an enormous amount of time learning about software, practices, new technologies, new patters, etc...I think I could spend a much smaller amount of time learning about networking and be just as "good". What are your thoughts? EDIT: This is not about making easy money. Networking and Software are closely related, I love computers and programming, but if I can work with both, make more money and have less stress in my life and can spend more time with my family, then I am willing to consider a change and hence I am looking for advice that Do or Don't support this view.

  Read the article

• Wake-on-lan only works so many times

  - by Chance

  I have Wake-on-lan configured on my Windows XP machine so that the computer will wake up from Standby. Waking the computer from Standby via network traffic seems to work a certain number of times, say 4 or 5, then it stops working. If I restart the computer it seems to reset this behavior so that I can use WOL a few more times before it starts working. I use the command "wol" on my other, Linux machine with the appropriate IP address and MAC address of the card. I looked at the network card to see if it had different lights when WOL worked and when it didn't. When it has a solid amber light where the ethernet cable connects, WOL seems to work. When it has a flashing amber light, WOL does not. It seems that the system seems to almost "shut off" the card when it falls to sleep, but I don't know if this is a function of time or number of standby/wakeups. I have a 3Com 3c920 network card. If I look at the properties in Device Manager, I have "Allow this Device to bring the Computer out of Standby" checked. In the Advanced tab I have anything related to RWU (Remote Wake Up) enabled. I also believe I have the appropriate settings in BIOS related to Remote Wake-Up and I have tried both S1 and S3 power configurations in the BIOS. Intuitively, I would think I would uncheck "Allow the Computer to turn off this device to save power", but doing so disables the "Allow this Device to bring the Computer out of Standby" option. Does anyone know what is happening here or if there is a way to fix it? I have an integrated network card; would getting one that goes into a slot be better? I am running Windows XP on a Dell Optiplex GX240 with a 3Com 3c920 network card.

  Read the article

• System wide Proxy settings when on a windows network with a password

  - by sav

  I'm using Ubuntu on a windows network. I want to connect to the world wide web. I have followed the steps here which I have found very useful. However when I try to ping a website (eg: ping www.wikipedia.org) I get no reply. I can ping local computers on my network, but I need to go through our proxy to get to the world wide web. I can even browse wikipedia using firefox, I just needed to enter the proxy configuration script location and my username and password. I'm quite sure the reason I'm having this trouble is because I havn't entered a username and password. I'm not sure how to do this on a system wide level. ultimately I would like to be able to use package managers like synaptic but first I need them to be able to connect to the internet. EDIT As sugested I created a /etc/apt/apt.conf file like Acquire::http::Proxy "http://chrisav:[email protected]:8080"; Acquire::https::Proxy "https://chrisav:[email protected]:8080"; Acquire::ftp::Proxy "ftp://chrisav:[email protected]:8080"; Acquire::socks::Proxy "socks://chrisav:[email protected]:8080"; However I still cant ping wikipedia when I try installing stuff I get chris@chris-Ubuntu:~$ sudo apt-get install kate Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package kate

  Read the article

• Does anyone know how to "tcpdump" traffic decrypted by Mallory MITM? [migrated]

  - by chriv

  I'm looking for some help in capturing network traffic that I can analyze in Wireshare (or other tools). The tool I'm using is mallory. If anyone is familiar with mallory, I could use some help. I've got it configured and running correctly, but I don't know how to get the output that I want. The setup is on my private network. I have a VM (running Ubuntu 12.04 - precise) with two NICs: eth0 is on my "real" network eth1 is only on my "fake" network, and is using dnsmasq (for DNS and DHCP for other devices on the "fake" network) Effectively eth0 is the "WAN" on my VM, and eth1 is the "LAN" on my VM. I've setup mallory and iptables to intercept, decrypt, encrypt and rewrite all traffic coming in on destination port 443 on eth1. On the device I want intercepted, I have imported the ca.cer that mallory generated as a trusted root certificate. I need to analyze some strange behavior in the HTTPS stream between the client and server, so that's why mallory is setup in between for this MITM. I would like to take the decrypted HTTPS traffic and dump it to either a logfile or a socket in a format compatible with tcpdump/wireshark (so I can collect it later and analyze it). Running tcpdump on eth1 is too soon (it's encrypted), and running tcpdump on eth2 is too late (it's been re-encrypted). Is there a way to make mallory "tcpdump" the decrypted traffic (in both directions)?

  Read the article

• Virtual IPv6 Network between VirtualBox VMs

  - by Ben

  I'm trying to create a virtual IPv6 network as a test environment. I have 5 VirtualBox VMs (Ubuntu Server) with network adapters using host-only networking. You can imagine them being connected in series and every machine connects 2 subnets. I want to ping the last machine from the first one: On: 2001:db8:aaaa::100 I want to ping 2001:db8:dddd::101 (Note: there is no cccc network in between) Only static configuration and routes are used: /etc/network/interfaces auto eth0 iface eth0 inet6 static address 2001:db8:aaaa::100 netmask 64 /etc/network/interfaces auto eth0 iface eth0 inet6 static address 2001:db8:aaaa::101 netmask 64 auto eth1 iface eth1 inet6 static address 2001:db8:bbbb::100 netmask 64 up ip -6 route add 2001:db8:dddd::/64 via 2001:db8:bbbb::101 dev eth1 down ip -6 route del 2001:db8:dddd::/64 via 2001:db8:bbbb::101 dev eth1 I thought there might be some automatic route discovery going on. Anyway, ping6 2001:db8:dddd::100 will not work from aaaa::100 When I add the route: ip -6 route add 2001:db8:dddd::/64 via 2001:db8:aaaa::101 it will work. But the next interface in the same network dddd::101 is not reachable. How could that be? There is a machine with an interface bbbb::101 and another dddd::100 and I can ping the latter one, but the machine connected to it, dddd::101 not?? I also have also turned on forwarding. Any ideas?

  Read the article

• Hidden features of Windows command prompt

  - by Nadir SOUALEM

  What are the lesser-known but useful features of the Windows command prompt?

  Read the article

• Serializing network messages

  - by mtsvetkov

  I am writing a network wrapper around boost::asio and was wondering what is a good and simple way to serialize my messages. I have a message factory which can take care of dispatching the data to the correct builder, but I want to know if there are any established solutions for getting the binary data on the sender side and consequently passing the data for deserialization on the receiver end. Some options I've explored are: passing a pointer to a char[] to the serialize/deserialize functions (for serialize to write to, and deserialize to read from), but it's difficult to enforce buffer size this way; building on that, I decided to have the serialize function return a boost::asio::mutable_buffer, however ownership of the memory gets blurred between multiple classes, as the network wrapper needs to clean up the memory allocated by the message builder. I have also seen solutions involving streambuf's and stringstream's, but manipulating binary data in terms of its string representation is something I want to avoid. Is there some sort of binary stream I can use instead? What I am looking for is a solution (preferrably using boost libs) that lets the message builder dictate the amount of memory allocated during serialization and what that would look like in terms of passing the data around between the wrapper and message factory/message builders. PS. Messages contain almost exclusively built-in types and PODs and form a shallow but wide hierarchy for the sake of going through a factory. Note: a link to examples of using boost::serialization for something like this would be appreciated as I'm having difficulties figuring out the relation between it and buffers.

  Read the article

• Hidden features of Ubuntu

  - by Tom Brito

  That I know: In command line, use TAB to autocomplete the commands. You need just to select a text to copy it, and use mouse middle button to paste. Which other "untold" secrets Ubuntu hides? obs. I don't know which of the items I told are for any Linux or Ubuntu specific.

  Read the article

• Unable to view 2 local sites over network

  - by gentrobot

  I have 2 websites running on my local machine that I'd like to view from other machines on the same network. For /etc/apache2/sites-available/site1.com: <VirtualHost *:80> ServerName site1.com DocumentRoot /var/www/answers/app/webroot DirectoryIndex index.php <Directory "/var/www/answers/app/webroot"> Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> For /etc/apache2/sites-available/site1.com: <VirtualHost *:80> ServerName site2.com DocumentRoot /var/www/answers2/app/webroot DirectoryIndex index.php <Directory "/var/www/answers2/app/webroot"> Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> I have added 2 entries in the /etc/hosts file as: 127.0.0.1 site1.com 127.0.0.1 site2.com Now, when I point the browser on my machine to site1.com, it shows me the first site and pointing the browser to site2.com, it shows me the second site. However,when I type in the local IP of my machine in the browser, it always shows site2. How can I change it to switch between site1 and site2 ? Is there a way that I can view both the sites form another machine (esp. mobile devices over wireless network) ?

  Read the article

• LSI1068E hidden drives after failed raid volume creation

  - by silk

  We are using LSI 1068E raid chipset with SAS drives. We had added new drives to the system, and tried to create new raid volume with the lsiutil, unfortunately the creation failed. The problem is that now we do not have the new raid volume and disks 'disappeared' and are not available as targets for raid. Lsiutil option 8 (scan for devices) does not display these disks at all. lsiutil option 16 (display attached devices) does list them as targets. lsiutil option 21+30 (create raid) does not list these disks. Just after insrting them to enclosure these disks appeared in the system, as expected. During the raid creation kernel logged: Mar 4 08:40:02 kilo kernel: [57555.687946] mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 2 id=0 Mar 4 08:40:02 kilo kernel: [57555.687978] mptbase: ioc0: PhysDisk has been created Mar 4 08:40:02 kilo kernel: [57555.695438] scsi target0:0:2: mptsas: ioc0: RAID Hidding: fw_channel=0, fw_id=0, physdsk 2, sas_addr 0x5000c50008ebe5fd for both of them, again as expected. Unfortunately they did not appear back even though the volume was not created. The same situation is in the controller's bios after a reboot. Taking the disks out and inserting in different slots did not help, either. Has someone seen a similar problem? And knows how to 'get back' our disks?

  Read the article

• How to Monitor Network in Medium-Sized Company?

  - by Kyle Lowry

  I work at a medium sized company (100+ employees). An issue that has been cropping up is network performance, internet access in particular. We have about 70 or more computers, a mix of Mac OS X and Windows XP & 7 machines. We have several servers (Exchange server, PC file servers, MS SQL, Blackberry, FTP, Mac server, etc). There are four main switches, a SonicWall firewall, and probably a couple routers in the server room with a dozen or so more scattered around the building. The network structure has grown organically over a number of years; and, as far as I know, there really isn't a monitoring solution in place. When we experience network issues (slow connections, dropped packets, and so on), our general solution is to power cycle some hardware or go around to each employee and ask them if they are uploading/downloading any large files. This is really inefficient and time consuming, and it does not allow us to monitor the network, tackling potential problems proactively. I would like to find a solution that would allow me to monitor network usage company-wide in real time, with detail going down to the individual computer, ideally. Given the hodgepodge of equipment and operating systems, what would be the best way to set up some kind of monitoring solution? Hardware, software, restructuring our network architecture?

  Read the article

• Choosing the correct network protocol for my type of game (its Wc3 Warlock style)

  - by Moritz

  I need to code a little game for a school project. The type of the game is like the Warcraft 3 map "Warlock", if anyone doesnt know it, here is a short description: up to ten players spawn into an arena filled with lava, the goal of each player is to push the other players into the lava with spells (basically variations of missiles, aoe nukes, moba spells etc) http://www.youtube.com/watch?v=c3PoO-gcJik&feature=related we need to provide multiplayer-support over the internet, for that reason I am looking for the best network protocol for this type of game (udp, tcp, lock step, client-server...) what the requirements are: - same/stable simulation on all clients - up to ten players - up to ~100 missiles on the field - very low latency since its reaction based (i dont know the method wc3 used, but it was playable with the old servers) what would be nice (if even possible, since the traffic might be too big): - support for soft bodies over the network (with bullet physics), but this is no real requirement I read several articles about the lock step method used for RTS games, this seems to be great, but does it fit for real-time action games too (ping-related)? If anyone has run into the same problems/questions like me, I would be very happy about any help

  Read the article

• "Hidden" facilities of Ubuntu (both graphical and command line)

  - by Tom Brito

  In command line, we have, for example, TAB, which autocomplete the commands. In the GUI, we need just to select a text for Ubuntu to copy it. And the mouse middle button can be used to paste. Which other "untold" secrets Ubuntu hides? obs. I don't know which of the items I told are for any Linux or Ubuntu specific.

  Read the article

• Xen HVM Windows 2008 network bridge

  - by JavierMartinz

  I have a problem with the Windows Server 2008 guest (hvm). I can't get a network interface running for him. I also have a Debian guest and it's working ok, but I can't do it with the Win2k8 guest. When I started the VM, the machine freezes and I can't connect by ssh to the host. /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 188.165.B.C netmask 255.255.255.0 network 188.165.B.0 broadcast 188.165.255.255 gateway 188.165.B.254 brctl show bridge name bridge id STP enabled interfaces eth0 8000.e840f20acc28 no peth0 /etc/xen/xend-config.sxp ... (vif-script vif-bridge) (network-script 'network-bridge') ... /etc/xen/win2k8.cfg # Networking # vif = [ 'ip=5.39.F.G,mac=yy:yy:yy:yy:yy:yy,type=ioemu,bridge=eth0' ] /etc/xen/debian.cfg # Networking # vif = [ 'ip=178.33.D.E,mac=xx:xx:xx:xx:xx:xx' ] As you can see, in the Debian guest I only have to specify an IP address and a MAC. But if I put that in the Win2k8 guest, the machine does not start. I am using Xen 4.0

  Read the article

• networking without port forwarding

  - by Wallacoloo

  I'm trying to add networking functionality to my game. I want any user to be able to host the game, and anyone to be able to connect as a client. The client sends info to the host about their player's position, etc. When the host receives a message, it validates it and then broadcasts it to its other clients. I will primarily be dealing with UDP, but will also need TCP for chat & lobby stuff. The problem is that I can't seem to get a packet sent from the client to the host or the other way around without enabling port forwarding on my router. But I don't think this is necessary. I believe the reason I need port forwarding is because I want to send a packet from 1 computer on a LAN to another computer on a different LAN, but neither of them have a global ip address since they're in a LAN. So really, I can only send packets targeting the other network's router, which must forward it on to the machine I want to reach. So how can I do this without port forwarding? Somehow a web server can communicate with my computer, which doesn't have a global ip, without port forwarding. And I've played plenty of multi-player games that don't require me to enable port forwarding. So it must be possible. Btw, I'm using SDL_Net. I don't think this will change anything though.

  Read the article

• Windows GPO default mapped drives

  - by SteB

  Is there a way, using Windows GPO, to set up a list of "default" mapped drives that can be applied to a group of users? I runs small network and would like to make sure that certain groups of users (like Sales or Support) have the same network shares mapped to the same drive letters irrespective of which PC they log onto. This would make the setup of new users easier and allow the centralised administration of the network locations shared. Any links to examples and/or step-by-step guides would be greatly appreciated.

  Read the article

• Windows Sharing requires password

  - by Linux Intel

  I have 3 machines on my local network Machine A , Machine B and Machine C OS on all machines is : Windows 7 64bit. Sharing Permissions on all machines : Everyone ( Read/Write ) no domain. Sharing folder name : project Machine A is sharing folder over the network without password. Machine B is sharing folder over the network without password. Machine C is sharing folder over the network without password. Machine A can normally access B and C without password required. Machine B can normally access A and C without password required Machine C can normally access Machine B without password. My problem is *Machine C* requires a password when it access Machine A also the shared folder in Machine A don't have password protected and Machine B can access Machine A without a password ! How can i solve the problem .?

  Read the article

< Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >