Search Results

Search found 2560 results on 103 pages for 'revision counter'.

Page 64/103 | < Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >

• error about ACPI _OSC request failed (AE_NOT_FOUND)

  - by Yavuz Maslak

  I have ubuntu server 11.10 64 bit I see an error in kernel.log. This error comes out when the server reboot. some port of grep APCI in kernel.log; Dec 5 09:08:51 www kernel: [ 0.588605] pci0000:00: Requesting ACPI _OSC control (0x1d) Dec 5 09:08:51 www kernel: [ 0.588667] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d Dec 5 09:08:51 www kernel: [ 0.588746] ACPI _OSC control for PCIe not granted, disabling ASPM Which hardware may be cause this error ? root@www:# grep -r ACPI /var/log/kern.log Dec 5 09:08:51 www kernel: [ 0.000000] BIOS-e820: 00000000bf780000 - 00000000bf798000 (ACPI data) Dec 5 09:08:51 www kernel: [ 0.000000] BIOS-e820: 00000000bf798000 - 00000000bf7dc000 (ACPI NVS) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: RSDP 00000000000fb1a0 00014 (v00 ACPIAM) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: RSDT 00000000bf780000 00040 (v01 022410 RSDT1405 20100224 MSFT 00000097) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: FACP 00000000bf780200 00084 (v01 022410 FACP1405 20100224 MSFT 00000097) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: DSDT 00000000bf7804b0 0C359 (v01 A1279 A1279001 00000001 INTL 20060113) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: FACS 00000000bf798000 00040 Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: APIC 00000000bf780390 000D8 (v01 022410 APIC1405 20100224 MSFT 00000097) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: MCFG 00000000bf780470 0003C (v01 022410 OEMMCFG 20100224 MSFT 00000097) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: OEMB 00000000bf798040 00072 (v01 022410 OEMB1405 20100224 MSFT 00000097) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: HPET 00000000bf78f4b0 00038 (v01 022410 OEMHPET 20100224 MSFT 00000097) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: OSFR 00000000bf78f4f0 000B0 (v01 022410 OEMOSFR 20100224 MSFT 00000097) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: SSDT 00000000bf798fe0 00363 (v01 DpgPmm CpuPm 00000012 INTL 20060113) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000 Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: PM-Timer IO Port: 0x808 Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000 Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x88] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x89] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x8a] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x8b] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x8c] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x8d] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x8e] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x10] lapic_id[0x8f] disabled) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfec8a000] gsi_base[24]) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: IRQ0 used by override. Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: IRQ2 used by override. Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: IRQ9 used by override. Dec 5 09:08:51 www kernel: [ 0.000000] Using ACPI (MADT) for SMP configuration information Dec 5 09:08:51 www kernel: [ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000 Dec 5 09:08:51 www kernel: [ 0.009507] ACPI: Core revision 20110413 Dec 5 09:08:51 www kernel: [ 0.499129] PM: Registering ACPI NVS region at bf798000 (278528 bytes) Dec 5 09:08:51 www kernel: [ 0.500749] ACPI: bus type pci registered Dec 5 09:08:51 www kernel: [ 0.502747] ACPI: EC: Look up EC in DSDT Dec 5 09:08:51 www kernel: [ 0.503788] ACPI: Executed 1 blocks of module-level executable AML code Dec 5 09:08:51 www kernel: [ 0.520435] ACPI: SSDT 00000000bf7980c0 00F20 (v01 DpgPmm P001Ist 00000011 INTL 20060113) Dec 5 09:08:51 www kernel: [ 0.520863] ACPI: Dynamic OEM Table Load: Dec 5 09:08:51 www kernel: [ 0.520990] ACPI: SSDT (null) 00F20 (v01 DpgPmm P001Ist 00000011 INTL 20060113) Dec 5 09:08:51 www kernel: [ 0.521308] ACPI: Interpreter enabled Dec 5 09:08:51 www kernel: [ 0.521366] ACPI: (supports S0 S1 S3 S4 S5) Dec 5 09:08:51 www kernel: [ 0.521611] ACPI: Using IOAPIC for interrupt routing Dec 5 09:08:51 www kernel: [ 0.522622] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources Dec 5 09:08:51 www kernel: [ 0.554150] ACPI: No dock devices found. Dec 5 09:08:51 www kernel: [ 0.554267] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug Dec 5 09:08:51 www kernel: [ 0.555231] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) Dec 5 09:08:51 www kernel: [ 0.588224] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] Dec 5 09:08:51 www kernel: [ 0.588398] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] Dec 5 09:08:51 www kernel: [ 0.588451] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] Dec 5 09:08:51 www kernel: [ 0.588473] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT] Dec 5 09:08:51 www kernel: [ 0.588492] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT] Dec 5 09:08:51 www kernel: [ 0.588512] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] Dec 5 09:08:51 www kernel: [ 0.588540] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE1._PRT] Dec 5 09:08:51 www kernel: [ 0.588559] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE3._PRT] Dec 5 09:08:51 www kernel: [ 0.588579] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE7._PRT] Dec 5 09:08:51 www kernel: [ 0.588605] pci0000:00: Requesting ACPI _OSC control (0x1d) Dec 5 09:08:51 www kernel: [ 0.588667] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d Dec 5 09:08:51 www kernel: [ 0.588746] ACPI _OSC control for PCIe not granted, disabling ASPM Dec 5 09:08:51 www kernel: [ 0.597666] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12 14 *15) Dec 5 09:08:51 www kernel: [ 0.598142] ACPI: PCI Interrupt Link [LNKB] (IRQs *5) Dec 5 09:08:51 www kernel: [ 0.598336] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12 14 15) Dec 5 09:08:51 www kernel: [ 0.598810] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 *10 11 12 14 15) Dec 5 09:08:51 www kernel: [ 0.599284] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 *14 15) Dec 5 09:08:51 www kernel: [ 0.599762] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 6 7 10 11 12 14 15) Dec 5 09:08:51 www kernel: [ 0.600236] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 *7 10 11 12 14 15) Dec 5 09:08:51 www kernel: [ 0.600709] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *4 6 7 10 11 12 14 15) Dec 5 09:08:51 www kernel: [ 0.601931] PCI: Using ACPI for IRQ routing Dec 5 09:08:51 www kernel: [ 0.628146] pnp: PnP ACPI init Dec 5 09:08:51 www kernel: [ 0.628211] ACPI: bus type pnp registered Dec 5 09:08:51 www kernel: [ 0.628417] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) Dec 5 09:08:51 www kernel: [ 0.628859] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active) Dec 5 09:08:51 www kernel: [ 0.628915] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) Dec 5 09:08:51 www kernel: [ 0.628951] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active) Dec 5 09:08:51 www kernel: [ 0.628975] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) Dec 5 09:08:51 www kernel: [ 0.629004] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active) Dec 5 09:08:51 www kernel: [ 0.629229] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 5 09:08:51 www kernel: [ 0.629779] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 5 09:08:51 www kernel: [ 0.629849] pnp 00:08: Plug and Play ACPI device, IDs PNP0103 (active) Dec 5 09:08:51 www kernel: [ 0.629901] pnp 00:09: Plug and Play ACPI device, IDs INT0800 (active) Dec 5 09:08:51 www kernel: [ 0.630030] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 5 09:08:51 www kernel: [ 0.630254] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 5 09:08:51 www kernel: [ 0.630304] pnp 00:0c: Plug and Play ACPI device, IDs PNP0303 PNP030b (active) Dec 5 09:08:51 www kernel: [ 0.630359] pnp 00:0d: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active) Dec 5 09:08:51 www kernel: [ 0.630492] system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 5 09:08:51 www kernel: [ 0.630986] system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active) Dec 5 09:08:51 www kernel: [ 0.631078] pnp: PnP ACPI: found 16 devices Dec 5 09:08:51 www kernel: [ 0.631135] ACPI: ACPI bus type pnp unregistered Dec 5 09:08:51 www kernel: [ 0.726291] ACPI: Power Button [PWRB] Dec 5 09:08:51 www kernel: [ 0.726452] ACPI: Power Button [PWRF] Dec 5 09:08:51 www kernel: [ 0.726527] ACPI: acpi_idle yielding to intel_idle Dec 7 21:45:22 www kernel: [ 0.000000] BIOS-e820: 00000000bf780000 - 00000000bf798000 (ACPI data) Dec 7 21:45:22 www kernel: [ 0.000000] BIOS-e820: 00000000bf798000 - 00000000bf7dc000 (ACPI NVS) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: RSDP 00000000000fb1a0 00014 (v00 ACPIAM) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: RSDT 00000000bf780000 00040 (v01 022410 RSDT1405 20100224 MSFT 00000097) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: FACP 00000000bf780200 00084 (v01 022410 FACP1405 20100224 MSFT 00000097) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: DSDT 00000000bf7804b0 0C359 (v01 A1279 A1279001 00000001 INTL 20060113) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: FACS 00000000bf798000 00040 Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: APIC 00000000bf780390 000D8 (v01 022410 APIC1405 20100224 MSFT 00000097) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: MCFG 00000000bf780470 0003C (v01 022410 OEMMCFG 20100224 MSFT 00000097) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: OEMB 00000000bf798040 00072 (v01 022410 OEMB1405 20100224 MSFT 00000097) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: HPET 00000000bf78f4b0 00038 (v01 022410 OEMHPET 20100224 MSFT 00000097) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: OSFR 00000000bf78f4f0 000B0 (v01 022410 OEMOSFR 20100224 MSFT 00000097) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: SSDT 00000000bf798fe0 00363 (v01 DpgPmm CpuPm 00000012 INTL 20060113) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000 Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: PM-Timer IO Port: 0x808 Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000 Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x88] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x89] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x8a] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x8b] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x8c] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x8d] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x8e] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x10] lapic_id[0x8f] disabled) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfec8a000] gsi_base[24]) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: IRQ0 used by override. Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: IRQ2 used by override. Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: IRQ9 used by override. Dec 7 21:45:22 www kernel: [ 0.000000] Using ACPI (MADT) for SMP configuration information Dec 7 21:45:22 www kernel: [ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000 Dec 7 21:45:22 www kernel: [ 0.009505] ACPI: Core revision 20110413 Dec 7 21:45:22 www kernel: [ 0.499203] PM: Registering ACPI NVS region at bf798000 (278528 bytes) Dec 7 21:45:22 www kernel: [ 0.500819] ACPI: bus type pci registered Dec 7 21:45:22 www kernel: [ 0.503121] ACPI: EC: Look up EC in DSDT Dec 7 21:45:22 www kernel: [ 0.504162] ACPI: Executed 1 blocks of module-level executable AML code Dec 7 21:45:22 www kernel: [ 0.520821] ACPI: SSDT 00000000bf7980c0 00F20 (v01 DpgPmm P001Ist 00000011 INTL 20060113) Dec 7 21:45:22 www kernel: [ 0.521247] ACPI: Dynamic OEM Table Load: Dec 7 21:45:22 www kernel: [ 0.521374] ACPI: SSDT (null) 00F20 (v01 DpgPmm P001Ist 00000011 INTL 20060113) Dec 7 21:45:22 www kernel: [ 0.521691] ACPI: Interpreter enabled Dec 7 21:45:22 www kernel: [ 0.521748] ACPI: (supports S0 S1 S3 S4 S5) Dec 7 21:45:22 www kernel: [ 0.521993] ACPI: Using IOAPIC for interrupt routing Dec 7 21:45:22 www kernel: [ 0.523002] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources Dec 7 21:45:22 www kernel: [ 0.554533] ACPI: No dock devices found. Dec 7 21:45:22 www kernel: [ 0.554649] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug Dec 7 21:45:22 www kernel: [ 0.555620] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) Dec 7 21:45:22 www kernel: [ 0.588224] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] Dec 7 21:45:22 www kernel: [ 0.588398] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] Dec 7 21:45:22 www kernel: [ 0.588451] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] Dec 7 21:45:22 www kernel: [ 0.588473] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT] Dec 7 21:45:22 www kernel: [ 0.588492] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT] Dec 7 21:45:22 www kernel: [ 0.588512] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] Dec 7 21:45:22 www kernel: [ 0.588540] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE1._PRT] Dec 7 21:45:22 www kernel: [ 0.588559] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE3._PRT] Dec 7 21:45:22 www kernel: [ 0.588579] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE7._PRT] Dec 7 21:45:22 www kernel: [ 0.588606] pci0000:00: Requesting ACPI _OSC control (0x1d) Dec 7 21:45:22 www kernel: [ 0.588667] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d Dec 7 21:45:22 www kernel: [ 0.588746] ACPI _OSC control for PCIe not granted, disabling ASPM Dec 7 21:45:22 www kernel: [ 0.597661] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12 14 *15) Dec 7 21:45:22 www kernel: [ 0.598137] ACPI: PCI Interrupt Link [LNKB] (IRQs *5) Dec 7 21:45:22 www kernel: [ 0.598331] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12 14 15) Dec 7 21:45:22 www kernel: [ 0.598804] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 *10 11 12 14 15) Dec 7 21:45:22 www kernel: [ 0.599278] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 *14 15) Dec 7 21:45:22 www kernel: [ 0.599756] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 6 7 10 11 12 14 15) Dec 7 21:45:22 www kernel: [ 0.600230] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 *7 10 11 12 14 15) Dec 7 21:45:22 www kernel: [ 0.600704] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *4 6 7 10 11 12 14 15) Dec 7 21:45:22 www kernel: [ 0.601926] PCI: Using ACPI for IRQ routing Dec 7 21:45:22 www kernel: [ 0.624115] pnp: PnP ACPI init Dec 7 21:45:22 www kernel: [ 0.624179] ACPI: bus type pnp registered Dec 7 21:45:22 www kernel: [ 0.624382] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) Dec 7 21:45:22 www kernel: [ 0.624821] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active) Dec 7 21:45:22 www kernel: [ 0.624875] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) Dec 7 21:45:22 www kernel: [ 0.624911] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active) Dec 7 21:45:22 www kernel: [ 0.624933] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) Dec 7 21:45:22 www kernel: [ 0.624962] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active) Dec 7 21:45:22 www kernel: [ 0.625186] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 7 21:45:22 www kernel: [ 0.625733] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 7 21:45:22 www kernel: [ 0.625803] pnp 00:08: Plug and Play ACPI device, IDs PNP0103 (active) Dec 7 21:45:22 www kernel: [ 0.625856] pnp 00:09: Plug and Play ACPI device, IDs INT0800 (active) Dec 7 21:45:22 www kernel: [ 0.625984] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 7 21:45:22 www kernel: [ 0.626206] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 7 21:45:22 www kernel: [ 0.626256] pnp 00:0c: Plug and Play ACPI device, IDs PNP0303 PNP030b (active) Dec 7 21:45:22 www kernel: [ 0.626312] pnp 00:0d: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active) Dec 7 21:45:22 www kernel: [ 0.626445] system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active) Dec 7 21:45:22 www kernel: [ 0.626936] system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active) Dec 7 21:45:22 www kernel: [ 0.627027] pnp: PnP ACPI: found 16 devices Dec 7 21:45:22 www kernel: [ 0.627084] ACPI: ACPI bus type pnp unregistered Dec 7 21:45:22 www kernel: [ 0.722086] ACPI: Power Button [PWRB] Dec 7 21:45:22 www kernel: [ 0.722246] ACPI: Power Button [PWRF] Dec 7 21:45:22 www kernel: [ 0.722320] ACPI: acpi_idle yielding to intel_idle

  Read the article

• Using Oracle Proxy Authentication with JPA (eclipselink-Style)

  - by olaf.heimburger

  Security is a very intriguing topic. You will find it everywhere and you need to implement it everywhere. Yes, you need. Unfortunately, one can easily forget it while implementing the last mile. The Last Mile In a multi-tier application it is a common practice to use connection pools between the business layer and the database layer. Connection pools are quite useful to speed database connection creation and to split the load. Another very common practice is to use a specific, often called technical, user to connect to the database. This user has authentication and authorization rules that apply to all application users. Imagine you've put every effort to define roles for different types of users that use your application. These roles are necessary to differentiate between normal users, premium users, and administrators (I bet you will find or already have more roles in your application). While these user roles are pretty well used within your application, once the flow of execution enters the database everything is gone. Each and every user just has one role and is the same database user. Issues? What Issues? As long as things go well, this is not a real issue. However, things do not go well all the time. Once your application becomes famous performance decreases in certain situations or, more importantly, current and upcoming regulations and laws require that your application must be able to apply different security measures on a per user role basis at every stage of your application. If you only have a bunch of users with the same name and role you are not able to find the application usage profile that causes the performance issue, or which user has accessed data that he/she is not allowed to. Another thread to your role concept is that databases tend to be used by different applications and tools. These tools can be developer tools like SQL*Plus, SQL Developer, etc. or end user applications like BI Publisher, Oracle Forms and so on. These tools have no idea of your applications role concept and access the database the way they think is appropriate. A big oversight for your perfect role model and a big nightmare for your Chief Security Officer. Speaking of the CSO, brings up another issue: Password management. Once your technical user account is compromised, every user is able to do things that he/she is not expected to do from the design of your application. Counter Measures In the Oracle world a common counter measure is to use Virtual Private Database (VPD). This restricts the values a database user can see to the allowed minimum. However, it doesn't help in regard of a connection pool user, because this one is still not the real user. Oracle Proxy Authentication Another feature of the Oracle database is Proxy Authentication. First introduced with version 9i it is a quite useful feature for nearly every situation. The main idea behind Proxy Authentication is, to create a crippled database user who has only connect rights. Even if this user is compromised the risks are well understood and fairly limited. This user can be used in every situation in which you need to connect to the database, no matter which tool or application (see above) you use.The proxy user is perfect for multi-tier connection pools. CREATE USER app_user IDENTIFIED BY abcd1234; GRANT CREATE SESSION TO app_user; But what if you need to access real data? Well, this is the primary use case, isn't it? Now is the time to bring the application's role concept into play. You define database roles that define the grants for your identified user groups. Once you have these groups you grant access through the proxy user with the application role to the specific user. CREATE ROLE app_role_a; GRANT app_role_a TO scott; ALTER USER scott GRANT CONNECT THROUGH app_user WITH ROLE app_role_a; Now, hr has permission to connect to the database through the proxy user. Through the role you can restrict the hr's rights the are needed for the application only. If hr connects to the database directly all assigned role and permissions apply. Testing the Setup To test the setup you can use SQL*Plus and connect to your database: $ sqlplus app_user[hr]/abcd1234 Java Persistence API The Java Persistence API (JPA) is a fairly easy means to build applications that retrieve data from the database and put it into Java objects. You use plain old Java objects (POJOs) and mixin some Java annotations that define how the attributes of the object are used for storing data from the database into the Java object. Here is a sample for objects from the HR sample schema EMPLOYEES table. When using Java annotations you only specify what can not be deduced from the code. If your Java class name is Employee but the table name is EMPLOYEES, you need to specify the table name, otherwise it will fail. package demo.proxy.ejb; import java.io.Serializable; import java.sql.Timestamp; import java.util.List; import javax.persistence.Column; import javax.persistence.Entity; import javax.persistence.Id; import javax.persistence.JoinColumn; import javax.persistence.ManyToOne; import javax.persistence.NamedQueries; import javax.persistence.NamedQuery; import javax.persistence.OneToMany; import javax.persistence.Table; @Entity @NamedQueries({ @NamedQuery(name = "Employee.findAll", query = "select o from Employee o") }) @Table(name = "EMPLOYEES") public class Employee implements Serializable { @Column(name="COMMISSION_PCT") private Double commissionPct; @Column(name="DEPARTMENT_ID") private Long departmentId; @Column(nullable = false, unique = true, length = 25) private String email; @Id @Column(name="EMPLOYEE_ID", nullable = false) private Long employeeId; @Column(name="FIRST_NAME", length = 20) private String firstName; @Column(name="HIRE_DATE", nullable = false) private Timestamp hireDate; @Column(name="JOB_ID", nullable = false, length = 10) private String jobId; @Column(name="LAST_NAME", nullable = false, length = 25) private String lastName; @Column(name="PHONE_NUMBER", length = 20) private String phoneNumber; private Double salary; @ManyToOne @JoinColumn(name = "MANAGER_ID") private Employee employee; @OneToMany(mappedBy = "employee") private List employeeList; public Employee() { } public Employee(Double commissionPct, Long departmentId, String email, Long employeeId, String firstName, Timestamp hireDate, String jobId, String lastName, Employee employee, String phoneNumber, Double salary) { this.commissionPct = commissionPct; this.departmentId = departmentId; this.email = email; this.employeeId = employeeId; this.firstName = firstName; this.hireDate = hireDate; this.jobId = jobId; this.lastName = lastName; this.employee = employee; this.phoneNumber = phoneNumber; this.salary = salary; } public Double getCommissionPct() { return commissionPct; } public void setCommissionPct(Double commissionPct) { this.commissionPct = commissionPct; } public Long getDepartmentId() { return departmentId; } public void setDepartmentId(Long departmentId) { this.departmentId = departmentId; } public String getEmail() { return email; } public void setEmail(String email) { this.email = email; } public Long getEmployeeId() { return employeeId; } public void setEmployeeId(Long employeeId) { this.employeeId = employeeId; } public String getFirstName() { return firstName; } public void setFirstName(String firstName) { this.firstName = firstName; } public Timestamp getHireDate() { return hireDate; } public void setHireDate(Timestamp hireDate) { this.hireDate = hireDate; } public String getJobId() { return jobId; } public void setJobId(String jobId) { this.jobId = jobId; } public String getLastName() { return lastName; } public void setLastName(String lastName) { this.lastName = lastName; } public String getPhoneNumber() { return phoneNumber; } public void setPhoneNumber(String phoneNumber) { this.phoneNumber = phoneNumber; } public Double getSalary() { return salary; } public void setSalary(Double salary) { this.salary = salary; } public Employee getEmployee() { return employee; } public void setEmployee(Employee employee) { this.employee = employee; } public List getEmployeeList() { return employeeList; } public void setEmployeeList(List employeeList) { this.employeeList = employeeList; } public Employee addEmployee(Employee employee) { getEmployeeList().add(employee); employee.setEmployee(this); return employee; } public Employee removeEmployee(Employee employee) { getEmployeeList().remove(employee); employee.setEmployee(null); return employee; } } JPA could be used in standalone applications and Java EE containers. In both worlds you normally create a Facade to retrieve or store the values of the Entities to or from the database. The Facade does this via an EntityManager which will be injected by the Java EE container. Here is sample Facade Session Bean for a Java EE container. package demo.proxy.ejb; import java.util.HashMap; import java.util.List; import javax.ejb.Local; import javax.ejb.Remote; import javax.ejb.Stateless; import javax.persistence.EntityManager; import javax.persistence.PersistenceContext; import javax.persistence.Query; import javax.interceptor.AroundInvoke; import javax.interceptor.InvocationContext; import oracle.jdbc.driver.OracleConnection; import org.eclipse.persistence.config.EntityManagerProperties; import org.eclipse.persistence.internal.jpa.EntityManagerImpl; @Stateless(name = "DataFacade", mappedName = "ProxyUser-TestEJB-DataFacade") @Remote @Local public class DataFacadeBean implements DataFacade, DataFacadeLocal { @PersistenceContext(unitName = "TestEJB") private EntityManager em; private String username; public Object queryByRange(String jpqlStmt, int firstResult, int maxResults) { // setSessionUser(); Query query = em.createQuery(jpqlStmt); if (firstResult 0) { query = query.setFirstResult(firstResult); } if (maxResults 0) { query = query.setMaxResults(maxResults); } return query.getResultList(); } public Employee persistEmployee(Employee employee) { // setSessionUser(); em.persist(employee); return employee; } public Employee mergeEmployee(Employee employee) { // setSessionUser(); return em.merge(employee); } public void removeEmployee(Employee employee) { // setSessionUser(); employee = em.find(Employee.class, employee.getEmployeeId()); em.remove(employee); } /** select o from Employee o */ public List getEmployeeFindAll() { Query q = em.createNamedQuery("Employee.findAll"); return q.getResultList(); } Putting Both Together To use Proxy Authentication with JPA and within a Java EE container you have to take care of the additional requirements: Use an OCI JDBC driver Provide the user name that connects through the proxy user Use an OCI JDBC driver To use the OCI JDBC driver you need to set up your JDBC data source file to use the correct JDBC URL. hr jdbc:oracle:oci8:@(DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=localhost)(PORT=1521))(CONNECT_DATA=(SID=XE))) oracle.jdbc.OracleDriver user app_user 62C32F70E98297522AD97E15439FAC0E SQL SELECT 1 FROM DUAL jdbc/hrDS Application Additionally you need to make sure that the version of the shared libraries of the OCI driver match the version of the JDBC driver in your Java EE container or Java application and are within your PATH (on Windows) or LD_LIBRARY_PATH (on most Unix-based systems). Installing the Oracle Database Instance Client software works perfectly. Provide the user name that connects through the proxy user This part needs some modification of your application software and session facade. Session Facade Changes In the Session Facade we must ensure that every call that goes through the EntityManager must be prepared correctly and uniquely assigned to this session. The second is really important, as the EntityManager works with a connection pool and can not guarantee that we set the proxy user on the connection that will be used for the database activities. To avoid changing every method call of the Session Facade we provide a method to set the username of the user that connects through the proxy user. This method needs to be called by the Facade client bfore doing anything else. public void setUsername(String name) { username = name; } Next we provide a means to instruct the TopLink EntityManager Delegate to use Oracle Proxy Authentication. (I love small helper methods to hide the nitty-gritty details and avoid repeating myself.) private void setSessionUser() { setSessionUser(username); } private void setSessionUser(String user) { if (user != null && !user.isEmpty()) { EntityManagerImpl emDelegate = ((EntityManagerImpl)em.getDelegate()); emDelegate.setProperty(EntityManagerProperties.ORACLE_PROXY_TYPE, OracleConnection.PROXYTYPE_USER_NAME); emDelegate.setProperty(OracleConnection.PROXY_USER_NAME, user); emDelegate.setProperty(EntityManagerProperties.EXCLUSIVE_CONNECTION_MODE, "Always"); } } The final step is use the EJB 3.0 AroundInvoke interceptor. This interceptor will be called around every method invocation. We therefore check whether the Facade methods will be called or not. If so, we set the user for proxy authentication and the normal method flow continues. @AroundInvoke public Object proxyInterceptor(InvocationContext invocationCtx) throws Exception { if (invocationCtx.getTarget() instanceof DataFacadeBean) { setSessionUser(); } return invocationCtx.proceed(); } Benefits Using Oracle Proxy Authentification has a number of additional benefits appart from implementing the role model of your application: Fine grained access control for temporary users of the account, without compromising the original password. Enabling database auditing and logging. Better identification of performance bottlenecks. References Effective Oracle Database 10g Security by Design, David Knox TopLink Developer's Guide, Chapter 98

  Read the article

• Partitioned Repository for WebCenter Content using Oracle Database 11g

  - by Adao Junior

  One of the biggest challenges for content management solutions is related to the storage management due the high volumes of the unstoppable growing of information. Even if you have storage appliances and a lot of terabytes, thinks like backup, compression, deduplication, storage relocation, encryption, availability could be a nightmare. One standard option that you have with the Oracle WebCenter Content is to store data to the database. And the Oracle Database allows you leverage features like compression, deduplication, encryption and seamless backup. But with a huge volume, the challenge is passed to the DBA to keep the WebCenter Content Database up and running. One solution is the use of DB partitions for your content repository, but what are the implications of this? Can I fit this with my business requirements? Well, yes. It’s up to you how you will manage that, you just need a good plan. During you “storage brainstorm plan” take in your mind what you need, such as storage petabytes of documents? You need everything on-line? There’s a way to logically separate the “good content” from the “legacy content”? The first thing that comes to my mind is to use the creation date of the document, but you need to remember that this document could receive a lot of revisions and maybe you can consider the revision creation date. Your plan can have also complex rules like per Document Type or per a custom metadata like department or an hybrid per date, per DocType and an specific virtual folder. Extrapolation the use, you can have your repository distributed in different servers, different disks, different disk types (Such as ssds, sas, sata, tape,…), separated accordingly your business requirements, separating the “hot” content from the legacy and easily matching your compliance requirements. If you think to use by revision, the simple way is to consider the dId, that is the sequential unique id for every content created using the WebCenter Content or the dLastModified that is the date field of the FileStorage table that contains the date of inclusion of the content to the DB Table using SecureFiles. Using the scenario of partitioned repository using an hierarchical separation by date, we will transform the FileStorage table in an partitioned table using  “Partition by Range” of the dLastModified column (You can use the dId or a join with other tables for other metadata such as dDocType, Security, etc…). The test scenario bellow covers: Previous existent data on the JDBC Storage to be migrated to the new partitioned JDBC Storage Partition by Date Automatically generation of new partitions based on a pre-defined interval (Available only with Oracle Database 11g+) Deduplication and Compression for legacy data Oracle WebCenter Content 11g PS5 (Could present some customizations that do not affect the test scenario) For the test case you need some data stored using JDBC Storage to be the “legacy” data. If you do not have done before, just create an Storage rule pointed to the JDBC Storage: Enable the metadata StorageRule in the UI and upload some documents using this rule. For this test case you can run using the schema owner or an dba user. We will use the schema owner TESTS_OCS. I can’t forgot to tell that this is just a test and you should do a proper backup of your environment. When you use the schema owner, you need some privileges, using the dba user grant the privileges needed: REM Grant privileges required for online redefinition. GRANT EXECUTE ON DBMS_REDEFINITION TO TESTS_OCS; GRANT ALTER ANY TABLE TO TESTS_OCS; GRANT DROP ANY TABLE TO TESTS_OCS; GRANT LOCK ANY TABLE TO TESTS_OCS; GRANT CREATE ANY TABLE TO TESTS_OCS; GRANT SELECT ANY TABLE TO TESTS_OCS; REM Privileges required to perform cloning of dependent objects. GRANT CREATE ANY TRIGGER TO TESTS_OCS; GRANT CREATE ANY INDEX TO TESTS_OCS; In our test scenario we will separate the content as Legacy, Day1, Day2, Day3 and Future. This last one will partitioned automatically using 3 tablespaces in a round robin mode. In a real scenario the partition rule could be per month, per year or any rule that you choose. Table spaces for the test scenario: CREATE TABLESPACE TESTS_OCS_PART_LEGACY DATAFILE 'tests_ocs_part_legacy.dat' SIZE 500K AUTOEXTEND ON NEXT 500K MAXSIZE UNLIMITED; CREATE TABLESPACE TESTS_OCS_PART_DAY1 DATAFILE 'tests_ocs_part_day1.dat' SIZE 500K AUTOEXTEND ON NEXT 500K MAXSIZE UNLIMITED; CREATE TABLESPACE TESTS_OCS_PART_DAY2 DATAFILE 'tests_ocs_part_day2.dat' SIZE 500K AUTOEXTEND ON NEXT 500K MAXSIZE UNLIMITED; CREATE TABLESPACE TESTS_OCS_PART_DAY3 DATAFILE 'tests_ocs_part_day3.dat' SIZE 500K AUTOEXTEND ON NEXT 500K MAXSIZE UNLIMITED; CREATE TABLESPACE TESTS_OCS_PART_ROUND_ROBIN_A 'tests_ocs_part_round_robin_a.dat' DATAFILE SIZE 500K AUTOEXTEND ON NEXT 500K MAXSIZE UNLIMITED; CREATE TABLESPACE TESTS_OCS_PART_ROUND_ROBIN_B 'tests_ocs_part_round_robin_b.dat' DATAFILE SIZE 500K AUTOEXTEND ON NEXT 500K MAXSIZE UNLIMITED; CREATE TABLESPACE TESTS_OCS_PART_ROUND_ROBIN_C 'tests_ocs_part_round_robin_c.dat' DATAFILE SIZE 500K AUTOEXTEND ON NEXT 500K MAXSIZE UNLIMITED; Before start, gather optimizer statistics on the actual FileStorage table: EXEC DBMS_STATS.GATHER_TABLE_STATS(USER, 'FileStorage', cascade => TRUE); Now check if is possible execute the redefinition process: EXEC DBMS_REDEFINITION.CAN_REDEF_TABLE('TESTS_OCS', 'FileStorage',DBMS_REDEFINITION.CONS_USE_PK); If no errors messages, you are good to go. Create a Partitioned Interim FileStorage table. You need to create a new table with the partition information to act as an interim table: CREATE TABLE FILESTORAGE_Part ( DID NUMBER(*,0) NOT NULL ENABLE, DRENDITIONID VARCHAR2(30 CHAR) NOT NULL ENABLE, DLASTMODIFIED TIMESTAMP (6), DFILESIZE NUMBER(*,0), DISDELETED VARCHAR2(1 CHAR), BFILEDATA BLOB ) LOB (BFILEDATA) STORE AS SECUREFILE ( ENABLE STORAGE IN ROW NOCACHE LOGGING KEEP_DUPLICATES NOCOMPRESS ) PARTITION BY RANGE (DLASTMODIFIED) INTERVAL (NUMTODSINTERVAL(1,'DAY')) STORE IN (TESTS_OCS_PART_ROUND_ROBIN_A, TESTS_OCS_PART_ROUND_ROBIN_B, TESTS_OCS_PART_ROUND_ROBIN_C) ( PARTITION FILESTORAGE_PART_LEGACY VALUES LESS THAN (TO_DATE('05-APR-2012 12.00.00 AM', 'DD-MON-YYYY HH.MI.SS AM')) TABLESPACE TESTS_OCS_PART_LEGACY LOB (BFILEDATA) STORE AS SECUREFILE ( TABLESPACE TESTS_OCS_PART_LEGACY RETENTION NONE DEDUPLICATE COMPRESS HIGH ), PARTITION FILESTORAGE_PART_DAY1 VALUES LESS THAN (TO_DATE('06-APR-2012 07.25.00 PM', 'DD-MON-YYYY HH.MI.SS AM')) TABLESPACE TESTS_OCS_PART_DAY1 LOB (BFILEDATA) STORE AS SECUREFILE ( TABLESPACE TESTS_OCS_PART_DAY1 RETENTION AUTO KEEP_DUPLICATES COMPRESS ), PARTITION FILESTORAGE_PART_DAY2 VALUES LESS THAN (TO_DATE('06-APR-2012 07.55.00 PM', 'DD-MON-YYYY HH.MI.SS AM')) TABLESPACE TESTS_OCS_PART_DAY2 LOB (BFILEDATA) STORE AS SECUREFILE ( TABLESPACE TESTS_OCS_PART_DAY2 RETENTION AUTO KEEP_DUPLICATES NOCOMPRESS ), PARTITION FILESTORAGE_PART_DAY3 VALUES LESS THAN (TO_DATE('06-APR-2012 07.58.00 PM', 'DD-MON-YYYY HH.MI.SS AM')) TABLESPACE TESTS_OCS_PART_DAY3 LOB (BFILEDATA) STORE AS SECUREFILE ( TABLESPACE TESTS_OCS_PART_DAY3 RETENTION AUTO KEEP_DUPLICATES NOCOMPRESS ) ); After the creation you should see your partitions defined. Note that only the fixed range partitions have been created, none of the interval partition have been created. Start the redefinition process: BEGIN DBMS_REDEFINITION.START_REDEF_TABLE( uname => 'TESTS_OCS' ,orig_table => 'FileStorage' ,int_table => 'FileStorage_PART' ,col_mapping => NULL ,options_flag => DBMS_REDEFINITION.CONS_USE_PK ); END; This operation can take some time to complete, depending how many contents that you have and on the size of the table. Using the DBA user you can check the progress with this command: SELECT * FROM v$sesstat WHERE sid = 1; Copy dependent objects: DECLARE redefinition_errors PLS_INTEGER := 0; BEGIN DBMS_REDEFINITION.COPY_TABLE_DEPENDENTS( uname => 'TESTS_OCS' ,orig_table => 'FileStorage' ,int_table => 'FileStorage_PART' ,copy_indexes => DBMS_REDEFINITION.CONS_ORIG_PARAMS ,copy_triggers => TRUE ,copy_constraints => TRUE ,copy_privileges => TRUE ,ignore_errors => TRUE ,num_errors => redefinition_errors ,copy_statistics => FALSE ,copy_mvlog => FALSE ); IF (redefinition_errors > 0) THEN DBMS_OUTPUT.PUT_LINE('>>> FileStorage to FileStorage_PART temp copy Errors: ' || TO_CHAR(redefinition_errors)); END IF; END; With the DBA user, verify that there's no errors: SELECT object_name, base_table_name, ddl_txt FROM DBA_REDEFINITION_ERRORS; *Note that will show 2 lines related to the constrains, this is expected. Synchronize the interim table FileStorage_PART: BEGIN DBMS_REDEFINITION.SYNC_INTERIM_TABLE( uname => 'TESTS_OCS', orig_table => 'FileStorage', int_table => 'FileStorage_PART'); END; Gather statistics on the new table: EXEC DBMS_STATS.GATHER_TABLE_STATS(USER, 'FileStorage_PART', cascade => TRUE); Complete the redefinition: BEGIN DBMS_REDEFINITION.FINISH_REDEF_TABLE( uname => 'TESTS_OCS', orig_table => 'FileStorage', int_table => 'FileStorage_PART'); END; During the execution the FileStorage table is locked in exclusive mode until finish the operation. After the last command the FileStorage table is partitioned. If you have contents out of the range partition, you should see the new partitions created automatically, not generating an error if you “forgot” to create all the future ranges. You will see something like: You now can drop the FileStorage_PART table: border-bottom-width: 1px; border-bottom-style: solid; text-align: left; border-left-color: silver; border-left-width: 1px; border-left-style: solid; padding-bottom: 4px; line-height: 12pt; background-color: #f4f4f4; margin-top: 20px; margin-right: 0px; margin-bottom: 10px; margin-left: 0px; padding-left: 4px; width: 97.5%; padding-right: 4px; font-family: 'Courier New', Courier, monospace; direction: ltr; max-height: 200px; font-size: 8pt; overflow-x: auto; overflow-y: auto; border-top-color: silver; border-top-width: 1px; border-top-style: solid; cursor: text; border-right-color: silver; border-right-width: 1px; border-right-style: solid; padding-top: 4px; " id="codeSnippetWrapper"> DROP TABLE FileStorage_PART PURGE; To check the FileStorage table is valid and is partitioned, use the command: SELECT num_rows,partitioned FROM user_tables WHERE table_name = 'FILESTORAGE'; You can list the contents of the FileStorage table in a specific partition, per example: SELECT * FROM FileStorage PARTITION (FILESTORAGE_PART_LEGACY) Some useful commands that you can use to check the partitions, note that you need to run using a DBA user: SELECT * FROM DBA_TAB_PARTITIONS WHERE table_name = 'FILESTORAGE';   SELECT * FROM DBA_TABLESPACES WHERE tablespace_name like 'TESTS_OCS%'; After the redefinition process complete you have a new FileStorage table storing all content that has the Storage rule pointed to the JDBC Storage and partitioned using the rule set during the creation of the temporary interim FileStorage_PART table. At this point you can test the WebCenter Content downloading the documents (Original and Renditions). Note that the content could be already in the cache area, take a look in the weblayout directory to see if a file with the same id is there, then click on the web rendition of your test file and see if have created the file and you can open, this means that is all working. The redefinition process can be repeated many times, this allow you test what the better layout, over and over again. Now some interesting maintenance actions related to the partitions: Make an tablespace read only. No issues viewing, the WebCenter Content do not alter the revisions When try to delete an content that is part of an read only tablespace, an error will occurs and the document will not be deleted The only way to prevent errors today is creating an custom component that checks the partitions and if you have an document in an “Read Only” repository, execute the deletion process of the metadata and mark the document to be deleted on the next db maintenance, like a new redefinition. Take an tablespace off-line for archiving purposes or any other reason. When you try open an document that is included in this tablespace will receive an error that was unable to retrieve the content, but the others online tablespaces are not affected. Same behavior when deleting documents. Again, an custom component is the solution. If you have an document “out of range”, the component can show an message that the repository for that document is offline. This can be extended to a option to the user to request to put online again. Moving some legacy content to an offline repository (table) using the Exchange option to move the content from one partition to a empty nonpartitioned table like FileStorage_LEGACY. Note that this option will remove the registers from the FileStorage and will not be able to open the stored content. You always need to keep in mind the indexes and constrains. An redefinition separating the original content (vault) from the renditions and separate by date ate the same time. This could be an option for DAM environments that want to have an special place for the renditions and put the original files in a storage with less performance. The process will be the same, you just need to change the script of the interim table to use composite partitioning. Will be something like: CREATE TABLE FILESTORAGE_RenditionPart ( DID NUMBER(*,0) NOT NULL ENABLE, DRENDITIONID VARCHAR2(30 CHAR) NOT NULL ENABLE, DLASTMODIFIED TIMESTAMP (6), DFILESIZE NUMBER(*,0), DISDELETED VARCHAR2(1 CHAR), BFILEDATA BLOB ) LOB (BFILEDATA) STORE AS SECUREFILE ( ENABLE STORAGE IN ROW NOCACHE LOGGING KEEP_DUPLICATES NOCOMPRESS ) PARTITION BY LIST (DRENDITIONID) SUBPARTITION BY RANGE (DLASTMODIFIED) ( PARTITION Vault VALUES ('primaryFile') ( SUBPARTITION FILESTORAGE_VAULT_LEGACY VALUES LESS THAN (TO_DATE('05-APR-2012 12.00.00 AM', 'DD-MON-YYYY HH.MI.SS AM')) LOB (BFILEDATA) STORE AS SECUREFILE , SUBPARTITION FILESTORAGE_VAULT_DAY1 VALUES LESS THAN (TO_DATE('06-APR-2012 07.25.00 PM', 'DD-MON-YYYY HH.MI.SS AM')) LOB (BFILEDATA) STORE AS SECUREFILE , SUBPARTITION FILESTORAGE_VAULT_DAY2 VALUES LESS THAN (TO_DATE('06-APR-2012 07.55.00 PM', 'DD-MON-YYYY HH.MI.SS AM')) LOB (BFILEDATA) STORE AS SECUREFILE , SUBPARTITION FILESTORAGE_VAULT_DAY3 VALUES LESS THAN (TO_DATE('06-APR-2012 07.58.00 PM', 'DD-MON-YYYY HH.MI.SS AM')) LOB (BFILEDATA) STORE AS SECUREFILE , SUBPARTITION FILESTORAGE_VAULT_FUTURE VALUES LESS THAN (MAXVALUE) ) ,PARTITION WebLayout VALUES ('webViewableFile') ( SUBPARTITION FILESTORAGE_WEBLAYOUT_LEGACY VALUES LESS THAN (TO_DATE('05-APR-2012 12.00.00 AM', 'DD-MON-YYYY HH.MI.SS AM')) LOB (BFILEDATA) STORE AS SECUREFILE , SUBPARTITION FILESTORAGE_WEBLAYOUT_DAY1 VALUES LESS THAN (TO_DATE('06-APR-2012 07.25.00 PM', 'DD-MON-YYYY HH.MI.SS AM')) LOB (BFILEDATA) STORE AS SECUREFILE , SUBPARTITION FILESTORAGE_WEBLAYOUT_DAY2 VALUES LESS THAN (TO_DATE('06-APR-2012 07.55.00 PM', 'DD-MON-YYYY HH.MI.SS AM')) LOB (BFILEDATA) STORE AS SECUREFILE , SUBPARTITION FILESTORAGE_WEBLAYOUT_DAY3 VALUES LESS THAN (TO_DATE('06-APR-2012 07.58.00 PM', 'DD-MON-YYYY HH.MI.SS AM')) LOB (BFILEDATA) STORE AS SECUREFILE , SUBPARTITION FILESTORAGE_WEBLAYOUT_FUTURE VALUES LESS THAN (MAXVALUE) ) ,PARTITION Special VALUES ('Special') ( SUBPARTITION FILESTORAGE_SPECIAL_LEGACY VALUES LESS THAN (TO_DATE('05-APR-2012 12.00.00 AM', 'DD-MON-YYYY HH.MI.SS AM')) LOB (BFILEDATA) STORE AS SECUREFILE , SUBPARTITION FILESTORAGE_SPECIAL_DAY1 VALUES LESS THAN (TO_DATE('06-APR-2012 07.25.00 PM', 'DD-MON-YYYY HH.MI.SS AM')) LOB (BFILEDATA) STORE AS SECUREFILE , SUBPARTITION FILESTORAGE_SPECIAL_DAY2 VALUES LESS THAN (TO_DATE('06-APR-2012 07.55.00 PM', 'DD-MON-YYYY HH.MI.SS AM')) LOB (BFILEDATA) STORE AS SECUREFILE , SUBPARTITION FILESTORAGE_SPECIAL_DAY3 VALUES LESS THAN (TO_DATE('06-APR-2012 07.58.00 PM', 'DD-MON-YYYY HH.MI.SS AM')) LOB (BFILEDATA) STORE AS SECUREFILE , SUBPARTITION FILESTORAGE_SPECIAL_FUTURE VALUES LESS THAN (MAXVALUE) ) )ENABLE ROW MOVEMENT; The next post related to partitioned repository will come with an sample component to handle the possible exceptions when you need to take off line an tablespace/partition or move to another place. Also, we can include some integration to the Retention Management and Records Management. Another subject related to partitioning is the ability to create an FileStore Provider pointed to a different database, raising the level of the distributed storage vs. performance. Let us know if this is important to you or you have an use case not listed, leave a comment. Cross-posted on the blog.ContentrA.com

  Read the article

• CodePlex Daily Summary for Friday, December 03, 2010

  CodePlex Daily Summary for Friday, December 03, 2010Popular ReleasesChronos WPF: Chronos v2.0 Beta 3: Release notes: Updated introduction document. Updated Visual Studio 2010 Extension (vsix) package. Added horizontal scrolling to the main window TaskBar. Added new styles for ListView, ListViewItem, GridViewColumnHeader, ... Added a new WindowViewModel class (allowing to fetch data). Added a new Navigate method (with several overloads) to the NavigationViewModel class (protected). Reimplemented Task usage for the WorkspaceViewModel.OnDelete method. Removed the reflection effect...MDownloader: MDownloader-0.15.26.7024: Fixed updater; Fixed MegauploadDJ - jQuery WebControls for ASP.NET: DJ 1.2: What is new? Update to support jQuery 1.4.2 Update to support jQuery ui 1.8.6 Update to Visual Studio 2010 New WebControls with samples added Autocomplete WebControl Button WebControl ToggleButt WebControl The example web site is including in source code project.LateBindingApi.Excel: LateBindingApi.Excel Release 0.7g: Unterschiede zur Vorgängerversion: - Zusätzliche Interior Properties - Group / Ungroup Methoden für Range - Bugfix COM Reference Handling für Application Objekt in einigen Klassen Release+Samples V0.7g: - Enthält Laufzeit DLL und Beispielprojekte Beispielprojekte: COMAddinExample - Demonstriert ein versionslos angebundenes COMAddin Example01 - Background Colors und Borders für Cells Example02 - Font Attributes undAlignment für Cells Example03 - Numberformats Example04 - Shapes, WordArts, P...ESRI ArcGIS Silverlight Toolkit: November 2010 - v2.1: ESRI ArcGIS Silverlight Toolkit v2.1 Added Windows Phone 7 build. New controls added: InfoWindow ChildPage (Windows Phone 7 only) See what's new here full details for : http://help.arcgis.com/en/webapi/silverlight/help/#/What_s_new_in_2_1/016600000025000000/ Note: Requires Visual Studio 2010, .NET 4.0 and Silverlight 4.0.ASP .NET MVC CMS (Content Management System): Atomic CMS 2.1.1: Atomic CMS 2.1.1 release notes Atomic CMS installation guide Winware: Winware 3.0 (.Net 4.0): Winware 3.0 is base on .Net 4.0 with C#. Please open it with Visual Studio 2010. This release contains a lab web application.UltimateJB: UltimateJB 2.02 PL3 KAKAROTO + CE-X-3.41 EvilSperm: Voici une version attendu avec impatience pour beaucoup : - La Version CEX341 pour pouvoir jouer avec des jeux demandant le firmware 3.50 ( certain ne fonctionne tous simplement pas ). - Pour l'instant le CEX341 n'est disponible qu'avec les PS3 en firmwares 3.41 !!! - La version PL3 KAKAROTO intégre ses dernières modification et intégre maintenant le firmware 3.30 !!! Conclusion : - UltimateJB CEX341 => Spoof le Firmware 3.41 en 3.50 ( facilite l'utilisation de certain jeux avec openManage...EnhSim: EnhSim 2.1.1: 2.1.1This release adds in the changes for 4.03a. To use this release, you must have the Microsoft Visual C++ 2010 Redistributable Package installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=A7B7A05E-6DE6-4D3A-A423-37BF0912DB84 To use the GUI you must have the .NET 4.0 Framework installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=9cfb2d51-5ff4-4491-b0e5-b386f32c0992 - Switched Searing Flames bac...AI: Initial 0.0.1: It’s simply just one code file; it simulates AI and machine in a simulated world. The AI has a little understanding of its body machine and parts, and able to use its feet to do actions just start and stop walking. The world is all of white with nothing but just the machine on a white planet. Colors, odors and position information make no sense. I’m previous C# programmer and I’m learning F# during this project, although I’m still not a good F# programmer, in this project I learning to prog...NKinect: NKinect Preview: Build features: Accelerometer reading Motor serial number property Realtime image update Realtime depth calculation Export to PLY (On demand) Control motor LED Control Kinect tiltMicrosoft - Domain Oriented N-Layered .NET 4.0 App Sample (Microsoft Spain): V1.0 - N-Layer DDD Sample App .NET 4.0: Required Software (Microsoft Base Software needed for Development environment) Visual Studio 2010 RTM & .NET 4.0 RTM (Final Versions) Expression Blend 4 SQL Server 2008 R2 Express/Standard/Enterprise Unity Application Block 2.0 - Published May 5th 2010 http://www.microsoft.com/downloads/en/details.aspx?FamilyID=2D24F179-E0A6-49D7-89C4-5B67D939F91B&displaylang=en http://unity.codeplex.com/releases/view/31277 PEX & MOLES 0.94.51023.0, 29/Oct/2010 - Visual Studio 2010 Power Tools http://re...Sense/Net Enterprise Portal & ECMS: SenseNet 6.0.1 Community Edition: Sense/Net 6.0.1 Community Edition This half year we have been working quite fiercely to bring you the long-awaited release of Sense/Net 6.0. Download this Community Edition to see what we have been up to. These months we have worked on getting the WebCMS capabilities of Sense/Net 6.0 up to par. New features include: New, powerful page and portlet editing experience. HTML and CSS cleanup, new, powerful site skinning system. Upgraded, lightning-fast indexing and query via Lucene. Limita...Minecraft GPS: Minecraft GPS 1.1.1: New Features Compass! New style. Set opacity on main window to allow overlay of Minecraft. Open World in any folder. Fixes Fixed style so listbox won't grow the window size. Fixed open file dialog issue on non-vista kernel machines.DotSpatial: DotSpatial 11-28-2001: This release introduces some exciting improvements. Support for big raster, both in display and changing the scheme. Faster raster scheme creation for all rasters. Caching of the "sample" values so once obtained the raster symbolizer dialog loads faster. Reprojection supported for raster and image classes. Affine transform fully supported for images and rasters, so skewed images are now possible. Projection uses better checks when loading unprojected layers. GDAL raster support f...Virtu: Virtu 0.9.0: Source Requirements.NET Framework 4 Visual Studio 2010 or Visual Studio 2010 Express Silverlight 4 Tools for Visual Studio 2010 Windows Phone 7 Developer Tools (which includes XNA Game Studio 4) Binaries RequirementsSilverlight 4 .NET Framework 4 XNA Framework 4SuperWebSocket: SuperWebSocket(60438): It is the first release of SuperWebSocket. Because it is base on SuperSocket, most features of SuperSocket are supported in SuperWebSocket. The source code include a LiveChat demo.Cropper: 1.9.4: Mostly fixes for issues with a few feature requests. Fixed Issues 2730 & 3638 & 14467 11044 11447 11448 11449 14665 Implemented Features 6123 11581PFC: PFC for PB 11.5: This is just a migration from the 11.0 code. No changes have been made yet (and they are needed) for it to work properly with 11.5.PDF Rider: PDF Rider 0.5: This release does not add any new feature for pdf manipulation, but enables automatic updates checking, so it is reccomended to install it in order to stay updated with next releases. Prerequisites * Microsoft Windows Operating Systems (XP - Vista - 7) * Microsoft .NET Framework 3.5 runtime * A PDF rendering software (i.e. Adobe Reader) that can be opened inside Internet Explorer. Installation instructionsChoose one of the following methods: 1. Download and run the "pdfRider0...New Projects.Net MVC Dialog Authentication Starter: .Net MVC Dialog Authentication Starter is the basic .Net MVC application starter template that has been modified to render the Register and Logon functionality via a modal dialog. It is developed using .Net MVC 2, Jquery 1.4.1, and Jquery UI 1.8.6..Net SQL Generator: Generation tool for random queries in SQL in the Windows environment. Can produce random queries, tables, deletes, and updates as well as generate random data for a table. Structured to allow easy adaptation for other SQL implementations as well.10010dshjlahfajhflkjhkjhherkjhfkja: 10010dshjlahfajhflkjhkjhherkjhfkjaBanshee: MOSS 2007 utility to detect authored links and headings in navigation structure of a site collection which point to the subweb's root instead of the subweb's welcome page. It's developed in C# and requires MOSS 2007 SP2 or later.Counter Strike Live Level editor: What is CSLIVE? A web browser based online 2d Shooter. It is clone of Counter Strike. Game supports the multiplayer game over internet or lan. And its Free to play! open souce! This project is still in development. Official open beta tests will be ran every day 20:00 - 21:00 +2GTCRM 2011 Style Templates: CRM 2011 Style Templates.DarkTimes: Having many projects at the sames time ? need an easy way to count those times ? here is a windows phone 7 app for this ^^ --------------------- Vous avez plusieurs projets en même temps ? besoin d'un moyen simple de compter ces temps ? voici une appli windows phone 7 pour ca ^^DSN Export-o-Matic 3000: DSN Export-o-Matic 3000 is a Windows application which allows you to export ODBC DSN Registry settings to a .reg file which can then be imported on another computer. It is written in C#.NET using Visual C# 2010 Express Edition.DYSS Game and AGE Game Engine for XNA: Did You Slay Something? (Working title) and AGE Game Engine for XNA Developed by Lucas LoreggiaExeCryptorNetWrapper: .NET Wrapper for ExeCryptor product (serial number checking functionalities only)ffmpegYAG: ffmpegYAG is a GUI for the popular ffmpeg audio/video processing toolFluentScheduler: A task scheduler that uses fluent interface to configure schedules. Useful for running cron jobs/automated tasks from your application. General Purpose Hash Function Algorithms: The General Purpose Hash Functions Library has the following mix of additive and rotative general purpose string hashing algorithms. HD Web FileManager: Incercam sa facem un singur fisier asp.net care sa faca managementul fisierelor pe un server web.iConverter: iConverter ?????????????。 iConverter is a character transcoding encoding conversion tool.LHA Social Work: Source control host for http://lhasocialwork.org.Mega Puzzle WP7: Mega Puzzle its a Puzzle game in Silverlight that run in Windows Phone 7.It's developed in C#MTConnect Managed Agent SDK: The MTConnect Managed SDK provides an Agent object model to facilitate exposing MTConnect data from your machine tools.Nebula - Image Lock / Unlock Software: Nebula - Image ( Jpg / bmp ) file lock / unlock software designed for simply changing file extension, so that files will be visible on HDD but not unless you change the extension. Written in Perl + Compiled into exe.Pushing - A Sokoban like Puzzle game: Pushing is a C# port of a little hobby project I created some years ago in C++. It's a Sokoban like Puzzle game. The old C++ version was just a 2D/Pseudo 3D Game, the new C# version will be a real 3D Game.RESTController: Provides a base class implementation for a RESTful controller model. Provides common functionality for the basic controller actions of List, Show, New, Edit, and Delete. It's meant to remove as much of the redundant code for MVC controllers as possible.Scientific Calculator ZENO-5000: HTML 5, CSS 3, jQuery: Scientific Calculator ZENO-5000 is a lightweight web application (<40kb), utilizing latest HTML5/CSS3 features and client-side jQuery/Java scripting. Application does not include any graphic files. It is portable, capable of running in online/offline modes on PC/mobile devicesSCR-Airplane Autopilot System: Automatyczny pilot samolotu - projekt na zaliczenie przedmiotu Systemy Czasu RzeczywistegoScriptonite: A lightweight system for scripting gameplay events for games such as RPGs. After integrating Scriptonite into your project, you create scripted events using an incredibly simple scripting language. Intended for XNA, but should work anywhere.Shelf: Shelf is a .NET library of common extension methods.SQLite ADO.NET for Windows Phone: Windows Phone is missing SQLite. This project fixes that :) And does so by giving the community the interfaces we've grown to know and love; IDbConnection, IDbCommand, IDbTransaction and, IDbReader. Thanks so much to the pioneers before me who ported the c++ to c#!Tailf: Tailf is a C# implementation of the tail -f command available on unix/linux systems. Differently form other ports it does not lock the file in any way so it works even if other rename the file: this is expecially designed to works well with log4net rolling file appender.TeamBrain: TeamBrain helps project teams to centralise all knowledge about a project into a repository that is clean and a pleasure to use.TeamDev JQuery c# wrapper: C# jQuery Wrapper. Helps you to write correct jQuery functions in c# language. The code you write will be traduced into correct jQuery methods calls. VirtualEye: Virtual Eye...Win32 Registry Activity Monitor: A simple program written in Delphi that monitors registry activity on win32 systems. In short a registry key and class are statically added to the code, the program is then run and as changes are made by other applications to the key and all its sub keys the changes are logged anXamlCode: XamlCode provides support for embedding inline C# code directly in the xaml files to create simple value converters, value providers and validation rules. It's targeted mainly as a rapid WPF application development tool.

  Read the article

• Acer aspire 5735z wireless not working after upgrade to 11.10

  - by Jon

  I cant get my wifi card to work at all after upgrading to 11.10 Oneiric. I'm not sure where to start to fix this. Ive tried using the additional drivers tool but this shows that no additional drivers are needed. Before my upgrade I had a drivers working for the Rt2860 chipset. Any help on this would be much appreciated.... thanks Jon jon@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1d:72:ec:76:d5 inet addr:192.168.1.134 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21d:72ff:feec:76d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7846 errors:0 dropped:0 overruns:0 frame:0 TX packets:7213 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8046624 (8.0 MB) TX bytes:1329442 (1.3 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:91 errors:0 dropped:0 overruns:0 frame:0 TX packets:91 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:34497 (34.4 KB) TX bytes:34497 (34.4 KB) Ive included by dmesg output below [ 0.428818] NET: Registered protocol family 2 [ 0.429003] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.430562] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.436614] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.437409] TCP: Hash tables configured (established 524288 bind 65536) [ 0.437412] TCP reno registered [ 0.437431] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.437482] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.437678] NET: Registered protocol family 1 [ 0.437705] pci 0000:00:02.0: Boot video device [ 0.437892] PCI: CLS 64 bytes, default 64 [ 0.437916] Simple Boot Flag at 0x57 set to 0x1 [ 0.438294] audit: initializing netlink socket (disabled) [ 0.438309] type=2000 audit(1319243447.432:1): initialized [ 0.440763] Freeing initrd memory: 13416k freed [ 0.468362] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.488192] VFS: Disk quotas dquot_6.5.2 [ 0.488254] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.488888] fuse init (API version 7.16) [ 0.488985] msgmni has been set to 5890 [ 0.489381] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.489413] io scheduler noop registered [ 0.489415] io scheduler deadline registered [ 0.489460] io scheduler cfq registered (default) [ 0.489583] pcieport 0000:00:1c.0: setting latency timer to 64 [ 0.489633] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X [ 0.489699] pcieport 0000:00:1c.1: setting latency timer to 64 [ 0.489741] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X [ 0.489800] pcieport 0000:00:1c.2: setting latency timer to 64 [ 0.489841] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X [ 0.489904] pcieport 0000:00:1c.3: setting latency timer to 64 [ 0.489944] pcieport 0000:00:1c.3: irq 43 for MSI/MSI-X [ 0.490006] pcieport 0000:00:1c.4: setting latency timer to 64 [ 0.490047] pcieport 0000:00:1c.4: irq 44 for MSI/MSI-X [ 0.490126] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.490149] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.490196] intel_idle: MWAIT substates: 0x1110 [ 0.490198] intel_idle: does not run on family 6 model 15 [ 0.491240] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.493473] ACPI: AC Adapter [ADP1] (on-line) [ 0.493590] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0 [ 0.496771] ACPI: Lid Switch [LID0] [ 0.496818] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 [ 0.496823] ACPI: Sleep Button [SLPB] [ 0.496865] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 [ 0.496869] ACPI: Power Button [PWRF] [ 0.496900] ACPI: acpi_idle registered with cpuidle [ 0.498719] Monitor-Mwait will be used to enter C-1 state [ 0.498753] Monitor-Mwait will be used to enter C-2 state [ 0.498761] Marking TSC unstable due to TSC halts in idle [ 0.517627] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.517630] ACPI: Thermal Zone [TZS0] (67 C) [ 0.524796] thermal LNXTHERM:01: registered as thermal_zone1 [ 0.524799] ACPI: Thermal Zone [TZS1] (67 C) [ 0.524823] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.524852] ERST: Table is not found! [ 0.524948] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.680991] ACPI: Battery Slot [BAT0] (battery present) [ 0.688567] Linux agpgart interface v0.103 [ 0.688672] agpgart-intel 0000:00:00.0: Intel GM45 Chipset [ 0.688865] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable [ 0.689786] agpgart-intel 0000:00:00.0: detected 65536K stolen memory [ 0.689912] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000 [ 0.691006] brd: module loaded [ 0.691510] loop: module loaded [ 0.691967] Fixed MDIO Bus: probed [ 0.691990] PPP generic driver version 2.4.2 [ 0.692065] tun: Universal TUN/TAP device driver, 1.6 [ 0.692067] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 0.692146] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.692181] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 20 (level, low) -> IRQ 20 [ 0.692206] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 0.692210] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 0.692255] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 0.692289] ehci_hcd 0000:00:1a.7: debug port 1 [ 0.696181] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported [ 0.696202] ehci_hcd 0000:00:1a.7: irq 20, io mem 0xf8904800 [ 0.712014] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 0.712131] hub 1-0:1.0: USB hub found [ 0.712136] hub 1-0:1.0: 6 ports detected [ 0.712230] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.712243] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 0.712247] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 0.712287] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 0.712315] ehci_hcd 0000:00:1d.7: debug port 1 [ 0.716201] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 0.716216] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf8904c00 [ 0.732014] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 0.732130] hub 2-0:1.0: USB hub found [ 0.732135] hub 2-0:1.0: 6 ports detected [ 0.732209] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.732223] uhci_hcd: USB Universal Host Controller Interface driver [ 0.732254] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 0.732262] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 0.732265] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 0.732298] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 0.732325] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001820 [ 0.732441] hub 3-0:1.0: USB hub found [ 0.732445] hub 3-0:1.0: 2 ports detected [ 0.732508] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 20 (level, low) -> IRQ 20 [ 0.732514] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 0.732518] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 0.732553] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 0.732577] uhci_hcd 0000:00:1a.1: irq 20, io base 0x00001840 [ 0.732696] hub 4-0:1.0: USB hub found [ 0.732700] hub 4-0:1.0: 2 ports detected [ 0.732762] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20 [ 0.732768] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 0.732772] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 0.732805] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 0.732829] uhci_hcd 0000:00:1a.2: irq 20, io base 0x00001860 [ 0.732942] hub 5-0:1.0: USB hub found [ 0.732946] hub 5-0:1.0: 2 ports detected [ 0.733007] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.733014] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.733017] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.733057] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 0.733082] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001880 [ 0.733202] hub 6-0:1.0: USB hub found [ 0.733206] hub 6-0:1.0: 2 ports detected [ 0.733265] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.733273] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.733276] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.733313] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 0.733351] uhci_hcd 0000:00:1d.1: irq 17, io base 0x000018a0 [ 0.733466] hub 7-0:1.0: USB hub found [ 0.733470] hub 7-0:1.0: 2 ports detected [ 0.733532] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.733539] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.733542] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.733578] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 0.733610] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018c0 [ 0.733730] hub 8-0:1.0: USB hub found [ 0.733736] hub 8-0:1.0: 2 ports detected [ 0.733843] i8042: PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 0.751594] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.751605] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.751732] mousedev: PS/2 mouse device common for all mice [ 0.752670] rtc_cmos 00:08: RTC can wake from S4 [ 0.752770] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 [ 0.752796] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 0.752907] device-mapper: uevent: version 1.0.3 [ 0.752976] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: [email protected] [ 0.753028] cpuidle: using governor ladder [ 0.753093] cpuidle: using governor menu [ 0.753096] EFI Variables Facility v0.08 2004-May-17 [ 0.753361] TCP cubic registered [ 0.753482] NET: Registered protocol family 10 [ 0.753966] NET: Registered protocol family 17 [ 0.753992] Registering the dns_resolver key type [ 0.754113] PM: Hibernation image not present or could not be loaded. [ 0.754131] registered taskstats version 1 [ 0.771553] Magic number: 15:152:507 [ 0.771667] rtc_cmos 00:08: setting system clock to 2011-10-22 00:30:48 UTC (1319243448) [ 0.772238] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 0.772240] EDD information not available. [ 0.774165] Freeing unused kernel memory: 984k freed [ 0.774504] Write protecting the kernel read-only data: 10240k [ 0.774755] Freeing unused kernel memory: 20k freed [ 0.775093] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3 [ 0.779727] Freeing unused kernel memory: 1400k freed [ 0.801946] udevd[84]: starting version 173 [ 0.880950] sky2: driver version 1.28 [ 0.881046] sky2 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.881096] sky2 0000:02:00.0: setting latency timer to 64 [ 0.881197] sky2 0000:02:00.0: Yukon-2 Extreme chip revision 2 [ 0.881871] sky2 0000:02:00.0: irq 45 for MSI/MSI-X [ 0.896273] sky2 0000:02:00.0: eth0: addr 00:1d:72:ec:76:d5 [ 0.910630] ahci 0000:00:1f.2: version 3.0 [ 0.910647] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.910710] ahci 0000:00:1f.2: irq 46 for MSI/MSI-X [ 0.910775] ahci: SSS flag set, parallel bus scan disabled [ 0.910812] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode [ 0.910816] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ccc ems sxs [ 0.910821] ahci 0000:00:1f.2: setting latency timer to 64 [ 0.941773] scsi0 : ahci [ 0.941954] scsi1 : ahci [ 0.942038] scsi2 : ahci [ 0.942118] scsi3 : ahci [ 0.942196] scsi4 : ahci [ 0.942268] scsi5 : ahci [ 0.942332] ata1: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904100 irq 46 [ 0.942336] ata2: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904180 irq 46 [ 0.942339] ata3: DUMMY [ 0.942340] ata4: DUMMY [ 0.942344] ata5: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904300 irq 46 [ 0.942347] ata6: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904380 irq 46 [ 1.028061] usb 1-5: new high speed USB device number 2 using ehci_hcd [ 1.181775] usbcore: registered new interface driver uas [ 1.260062] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.261126] ata1.00: ATA-8: Hitachi HTS543225L9A300, FBEOC40C, max UDMA/133 [ 1.261129] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 1.262360] ata1.00: configured for UDMA/133 [ 1.262518] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54322 FBEO PQ: 0 ANSI: 5 [ 1.262716] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.262762] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB) [ 1.262824] sd 0:0:0:0: [sda] Write Protect is off [ 1.262827] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.262851] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.287277] sda: sda1 sda2 sda3 [ 1.287693] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.580059] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.581188] ata2.00: ATAPI: HL-DT-STDVDRAM GT10N, 1.00, max UDMA/100 [ 1.582663] ata2.00: configured for UDMA/100 [ 1.584162] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GT10N 1.00 PQ: 0 ANSI: 5 [ 1.585821] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.585824] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.585953] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 1.586038] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 1.632061] usb 6-1: new low speed USB device number 2 using uhci_hcd [ 1.908056] ata5: SATA link down (SStatus 0 SControl 300) [ 2.228065] ata6: SATA link down (SStatus 0 SControl 300) [ 2.228955] Initializing USB Mass Storage driver... [ 2.229052] usbcore: registered new interface driver usb-storage [ 2.229054] USB Mass Storage support registered. [ 2.235827] scsi6 : usb-storage 1-5:1.0 [ 2.235987] usbcore: registered new interface driver ums-realtek [ 2.244451] input: B16_b_02 USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0/input/input4 [ 2.244598] generic-usb 0003:046D:C025.0001: input,hidraw0: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-1/input0 [ 2.244620] usbcore: registered new interface driver usbhid [ 2.244622] usbhid: USB HID core driver [ 3.091083] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null) [ 3.238275] scsi 6:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS [ 3.348261] sd 6:0:0:0: Attached scsi generic sg2 type 0 [ 3.351897] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 47.138012] udevd[334]: starting version 173 [ 47.177678] lp: driver loaded but no devices found [ 47.197084] wmi: Mapper loaded [ 47.197526] acer_wmi: Acer Laptop ACPI-WMI Extras [ 47.210227] acer_wmi: Brightness must be controlled by generic video driver [ 47.566578] Disabling lock debugging due to kernel taint [ 47.584050] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 47.620666] type=1400 audit(1319239895.347:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=624 comm="apparmor_parser" [ 47.620934] type=1400 audit(1319239895.347:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=624 comm="apparmor_parser" [ 47.621108] type=1400 audit(1319239895.347:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=624 comm="apparmor_parser" [ 47.633056] [drm] Initialized drm 1.1.0 20060810 [ 47.722594] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 47.722602] i915 0000:00:02.0: setting latency timer to 64 [ 47.807152] ndiswrapper (check_nt_hdr:141): kernel is 64-bit, but Windows driver is not 64-bit;bad magic: 010B [ 47.807159] ndiswrapper (load_sys_files:206): couldn't prepare driver 'rt2860' [ 47.807930] ndiswrapper (load_wrap_driver:108): couldn't load driver rt2860; check system log for messages from 'loadndisdriver' [ 47.856250] usbcore: registered new interface driver ndiswrapper [ 47.861772] i915 0000:00:02.0: irq 47 for MSI/MSI-X [ 47.861781] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 47.861783] [drm] Driver supports precise vblank timestamp query. [ 47.861842] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 47.980620] fixme: max PWM is zero. [ 48.286153] fbcon: inteldrmfb (fb0) is primary device [ 48.287033] Console: switching to colour frame buffer device 170x48 [ 48.287062] fb0: inteldrmfb frame buffer device [ 48.287064] drm: registered panic notifier [ 48.333883] acpi device:02: registered as cooling_device2 [ 48.334053] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5 [ 48.334128] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 48.334203] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 48.334644] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0 [ 48.334652] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0 [ 48.334673] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 48.334737] HDA Intel 0000:00:1b.0: irq 48 for MSI/MSI-X [ 48.334772] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 48.356107] Adding 261116k swap on /host/ubuntu/disks/swap.disk. Priority:-1 extents:1 across:261116k [ 48.380946] hda_codec: ALC268: BIOS auto-probing. [ 48.390242] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6 [ 48.390365] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [ 48.490870] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,user_xattr [ 48.917990] ppdev: user-space parallel port driver [ 48.950729] type=1400 audit(1319239896.675:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=941 comm="apparmor_parser" [ 48.951114] type=1400 audit(1319239896.675:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=941 comm="apparmor_parser" [ 48.977706] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa44000/0xa0000 [ 49.048871] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8 [ 49.078713] sky2 0000:02:00.0: eth0: enabling interface [ 49.079462] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 50.762266] sky2 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control rx [ 50.762702] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 54.751478] type=1400 audit(1319239902.475:7): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm-guest-session-wrapper" pid=1039 comm="apparmor_parser" [ 54.755907] type=1400 audit(1319239902.479:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1040 comm="apparmor_parser" [ 54.756237] type=1400 audit(1319239902.483:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1040 comm="apparmor_parser" [ 54.756417] type=1400 audit(1319239902.483:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1040 comm="apparmor_parser" [ 54.764825] type=1400 audit(1319239902.491:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=1041 comm="apparmor_parser" [ 54.768365] type=1400 audit(1319239902.495:12): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=1041 comm="apparmor_parser" [ 54.770601] type=1400 audit(1319239902.495:13): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=1041 comm="apparmor_parser" [ 54.770729] type=1400 audit(1319239902.495:14): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=1038 comm="apparmor_parser" [ 54.775181] type=1400 audit(1319239902.499:15): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1043 comm="apparmor_parser" [ 54.775533] type=1400 audit(1319239902.499:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1043 comm="apparmor_parser" [ 54.936691] init: failsafe main process (891) killed by TERM signal [ 54.944583] init: apport pre-start process (1096) terminated with status 1 [ 55.000373] init: apport post-stop process (1160) terminated with status 1 [ 55.005291] init: gdm main process (1159) killed by TERM signal [ 59.782579] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,user_xattr,commit=0 [ 60.992021] eth0: no IPv6 routers present [ 61.936072] device eth0 entered promiscuous mode [ 62.053949] Bluetooth: Core ver 2.16 [ 62.054005] NET: Registered protocol family 31 [ 62.054007] Bluetooth: HCI device and connection manager initialized [ 62.054010] Bluetooth: HCI socket layer initialized [ 62.054012] Bluetooth: L2CAP socket layer initialized [ 62.054993] Bluetooth: SCO socket layer initialized [ 62.058750] Bluetooth: RFCOMM TTY layer initialized [ 62.058758] Bluetooth: RFCOMM socket layer initialized [ 62.058760] Bluetooth: RFCOMM ver 1.11 [ 62.059428] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 62.059432] Bluetooth: BNEP filters: protocol multicast [ 62.460389] init: plymouth-stop pre-start process (1662) terminated with status 1 '

  Read the article

• Hard Disk DRDY error: is it a crash

  - by pranjal

  I am using IBM Thinkpad, 1.7GHz, 512 RAM with Linux Mint 9 installed. I have two partitions in addition to root. One of the partitions became read-only yesterday, after which I rebooted my system. It is extremely slow along with DRDY Error : Is my Hard disk crashed ? Error Log while booting. Differences between boot sector and its backup. failed command : READ DMA BMDMA : stat 0X25 ata 1.00 : status : { DRDY ERR } ata 1.00 : status :{ UNC } Buffer I/O error on logical device, logical block 65467 smartctl output for the partition: mint mint # smartctl -a /dev/sda1 smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: TOSHIBA MK4026GAX RoHS Serial Number: X5LY1623T Firmware Version: PA107E User Capacity: 40,007,761,920 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 6 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Thu Feb 17 06:48:25 2011 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 153) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 310 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 3968 5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 40 7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 082 082 000 Old_age Always - 7257 10 Spin_Retry_Count 0x0033 179 100 030 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3484 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 489 193 Load_Cycle_Count 0x0032 064 064 000 Old_age Always - 367150 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 36 (Lifetime Min/Max 14/57) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 33 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 82 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 1 199 UDMA_CRC_Error_Count 0x0032 200 253 000 Old_age Always - 0 220 Disk_Shift 0x0002 100 100 000 Old_age Always - 101 222 Loaded_Hours 0x0032 085 085 000 Old_age Always - 6146 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0 224 Load_Friction 0x0022 100 100 000 Old_age Always - 0 226 Load-in_Time 0x0026 100 100 000 Old_age Always - 227 240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0 SMART Error Log Version: 1 ATA Error Count: 2371 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2371 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:03:10.061 READ DMA f8 00 00 00 00 00 e0 00 00:03:10.061 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:03:10.053 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:03:10.053 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:03:10.053 READ NATIVE MAX ADDRESS Error 2370 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:03:03.328 READ DMA f8 00 00 00 00 00 e0 00 00:03:03.327 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:03:03.320 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:03:03.319 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:03:03.319 READ NATIVE MAX ADDRESS Error 2369 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:02:56.582 READ DMA f8 00 00 00 00 00 e0 00 00:02:56.582 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:02:56.574 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:02:56.574 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:02:56.574 READ NATIVE MAX ADDRESS Error 2368 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:02:49.809 READ DMA f8 00 00 00 00 00 e0 00 00:02:49.809 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:02:49.801 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:02:49.801 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:02:49.801 READ NATIVE MAX ADDRESS Error 2367 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:02:43.056 READ DMA f8 00 00 00 00 00 e0 00 00:02:43.056 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:02:43.048 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:02:43.048 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:02:43.047 READ NATIVE MAX ADDRESS SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Device does not support Selective Self Tests/Logging Do I need to get a new Hard Disk my PC ?

  Read the article

• ESX3.5 Cluster & MD3000i -- Both servers see iSCSI Targets, Only one server can use partition.

  - by GruffTech

  Alright. First and foremost, Warning. This is a bigger-then-normal question. I like to be thorough and try to eliminate all possible "easymode" answers, as well as give everyone a feel of what i've tried. I've included several images of our setup and the problem it is having.. TLDR Version: So I've followed the guides located here: ESX Deployment Guide V1 this is the guide Dell has sent me to setup two ESX3.5 servers mounting a Dell MD3000i. It doesn't work. Both servers can't use the same storage partition on the MD3000. Both servers see it, but only one server can actually use it. (that server being whatever server created the partition on the target.) Both ESX servers are members of the Host Group. Full Version I have 2 ESX3.5 Servers (10.0.7.102, also called EPI2, and 10.0.7.103, also called EPI3.) connected to a iSCSI SAN Device (Dell MD3000i). Both ESX servers can "scan" the SAN and see the LUNS. Part One: MD3000i Storage On the MD3000i, Both servers are in my host group. I have two partitions, VM1 and VM2, both 1.6TB (vmware doesn't like anything past 2tb.) And you can even see that the ESX servers are targetting the MD3000 just fine. Part Two: The ESX Servers Figure 1. So as you can see above, Both ESX Servers (10.0.7.102 and 10.0.7.103) are able to see and scan the MD3000i SAN. Figure 2. Above is the storage both servers see. I created the storage partition on EPI2 (102). I then Extended the partition to include the second LUN for a grand total of 3.27 TB of storage. When i "rescan" on 103 (the server not mounting the partition), I get the below log in log/messages. Mar 11 10:41:18 epi3 kernel: scsi1: remove-single-device 0 0 0 failed, device busy(4). being the only line that grabs my attentions. (EPI3 is the server name) Mar 11 10:41:04 epi3 vmkiscsid[5436]: Connected to Discovery Address 192.168.130.101 Mar 11 10:41:04 epi3 vmkiscsid[5437]: Connected to Discovery Address 192.168.130.102 Mar 11 10:41:04 epi3 vmkiscsid[5438]: Connected to Discovery Address 192.168.131.101 Mar 11 10:41:04 epi3 vmkiscsid[5439]: Connected to Discovery Address 192.168.131.102 Mar 11 10:41:17 epi3 kernel: scsi singledevice 2 0 0 0 Mar 11 10:41:17 epi3 kernel: Vendor: DELL Model: MD3000i Rev: 0735 Mar 11 10:41:17 epi3 kernel: Type: Direct-Access ANSI SCSI revision: 05 Mar 11 10:41:17 epi3 kernel: VMWARE SCSI Id: Supported VPD pages for sdb : 0x0 0x80 0x83 0x85 0x86 0x87 0xc0 0xc1 0xc2 0xc3 0xc4 0xc8 0xc9 0xca 0xd0 Mar 11 10:41:17 epi3 kernel: VMWARE SCSI Id: Device id info for sdb: 0x1 0x3 0x0 0x10 0x60 0x1 0xe4 0xf0 0x0 0x1a 0x1a 0xa2 0x0 0x0 0x15 0xe2 0x4d 0x75 0xf6 0x99 0x53 0x98 0x0 0x54 0x69 0x71 0x6e 0x2e 0x31 0x39 0x38 0x34 0x2d 0x30 0x35 0x2e 0x63 0x6f 0x6d 0x2e 0x64 0x65 0x6c 0x6c 0x3a 0x70 0x6f 0x77 0x65 0x72 0x76 0x61 0x75 0x6c 0x74 0x2e 0x36 0x30 0x30 0x31 0x65 0x34 0x66 0x30 0x30 0x30 0x31 0x61 0x31 0x61 0x61 0x32 0x30 0x30 0x30 0x30 0x30 0x30 0x30 0x30 0x34 0x37 0x39 0x30 0x36 0x32 0x32 0x65 0x2c 0x74 0x2c 0x30 0x78 0x30 0x30 0x30 0x31 0x30 0x30 0x30 0x30 0x30 0x30 0x30 0x32 0x0 0x0 0x0 0x51 0x94 0x0 0x4 0x0 0x0 0x80 0x1 0x53 0xa8 0x0 0x44 0x69 0x71 0x6e 0x2e 0x31 0x39 0x38 0x34 0x2d 0x30 0x35 0x2e 0x63 0x6f 0x6d 0x2e 0x64 0x65 0x6c 0x6c 0x3a 0x70 0x6f 0x77 0x65 0x72 0x76 0x61 0x75 0x6c 0x74 0x2e 0x36 0x30 0x30 0x31 0x65 0x34 0x66 0x30 0x30 0x30 0x31 0x61 0x31 0x61 0x61 0x32 0x30 0x30 0x30 0x30 0x30 0x30 0x30 0x30 0x34 0x37 0x39 0x30 0x36 0x32 0x32 0x65 0x0 0x0 0x0 0x0 Mar 11 10:41:17 epi3 kernel: VMWARE SCSI Id: Id for sdb 0x60 0x01 0xe4 0xf0 0x00 0x1a 0x1a 0xa2 0x00 0x00 0x15 0xe2 0x4d 0x75 0xf6 0x99 0x4d 0x44 0x33 0x30 0x30 0x30 Mar 11 10:41:17 epi3 kernel: VMWARE: Unique Device attached as scsi disk sdb at scsi2, channel 0, id 0, lun 0 Mar 11 10:41:17 epi3 kernel: Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0 Mar 11 10:41:17 epi3 kernel: scan_scsis starting finish Mar 11 10:41:17 epi3 kernel: SCSI device sdb: 3509329920 512-byte hdwr sectors (1797751 MB) Mar 11 10:41:17 epi3 kernel: sdb: sdb1 Mar 11 10:41:17 epi3 kernel: scan_scsis done with finish Mar 11 10:41:17 epi3 kernel: scsi singledevice 2 0 0 1 Mar 11 10:41:17 epi3 kernel: Vendor: DELL Model: MD3000i Rev: 0735 Mar 11 10:41:17 epi3 kernel: Type: Direct-Access ANSI SCSI revision: 05 Mar 11 10:41:18 epi3 kernel: VMWARE SCSI Id: Supported VPD pages for sdc : 0x0 0x80 0x83 0x85 0x86 0x87 0xc0 0xc1 0xc2 0xc3 0xc4 0xc8 0xc9 0xca 0xd0 Mar 11 10:41:18 epi3 kernel: VMWARE SCSI Id: Device id info for sdc: 0x1 0x3 0x0 0x10 0x60 0x1 0xe4 0xf0 0x0 0x1a 0x1a 0x86 0x0 0x0 0xd 0xb7 0x4d 0x75 0xf2 0x77 0x53 0x98 0x0 0x54 0x69 0x71 0x6e 0x2e 0x31 0x39 0x38 0x34 0x2d 0x30 0x35 0x2e 0x63 0x6f 0x6d 0x2e 0x64 0x65 0x6c 0x6c 0x3a 0x70 0x6f 0x77 0x65 0x72 0x76 0x61 0x75 0x6c 0x74 0x2e 0x36 0x30 0x30 0x31 0x65 0x34 0x66 0x30 0x30 0x30 0x31 0x61 0x31 0x61 0x61 0x32 0x30 0x30 0x30 0x30 0x30 0x30 0x30 0x30 0x34 0x37 0x39 0x30 0x36 0x32 0x32 0x65 0x2c 0x74 0x2c 0x30 0x78 0x30 0x30 0x30 0x31 0x30 0x30 0x30 0x30 0x30 0x30 0x30 0x32 0x0 0x0 0x0 0x51 0x94 0x0 0x4 0x0 0x0 0x80 0x1 0x53 0xa8 0x0 0x44 0x69 0x71 0x6e 0x2e 0x31 0x39 0x38 0x34 0x2d 0x30 0x35 0x2e 0x63 0x6f 0x6d 0x2e 0x64 0x65 0x6c 0x6c 0x3a 0x70 0x6f 0x77 0x65 0x72 0x76 0x61 0x75 0x6c 0x74 0x2e 0x36 0x30 0x30 0x31 0x65 0x34 0x66 0x30 0x30 0x30 0x31 0x61 0x31 0x61 0x61 0x32 0x30 0x30 0x30 0x30 0x30 0x30 0x30 0x30 0x34 0x37 0x39 0x30 0x36 0x32 0x32 0x65 0x0 0x0 0x0 0x0 Mar 11 10:41:18 epi3 kernel: VMWARE SCSI Id: Id for sdc 0x60 0x01 0xe4 0xf0 0x00 0x1a 0x1a 0x86 0x00 0x00 0x0d 0xb7 0x4d 0x75 0xf2 0x77 0x4d 0x44 0x33 0x30 0x30 0x30 Mar 11 10:41:18 epi3 kernel: VMWARE: Unique Device attached as scsi disk sdc at scsi2, channel 0, id 0, lun 1 Mar 11 10:41:18 epi3 kernel: Attached scsi disk sdc at scsi2, channel 0, id 0, lun 1 Mar 11 10:41:18 epi3 kernel: scan_scsis starting finish Mar 11 10:41:18 epi3 kernel: SCSI device sdc: 3509329920 512-byte hdwr sectors (1797751 MB) Mar 11 10:41:18 epi3 kernel: sdc: sdc1 Mar 11 10:41:18 epi3 kernel: scan_scsis done with finish Mar 11 10:41:18 epi3 kernel: scsi1: remove-single-device 0 0 0 failed, device busy(4). Mar 11 10:41:18 epi3 kernel: scsi singledevice 1 0 0 0 Things I've Tried: Removing iSCSI targets from only 103, disabling iSCSI, rebooting, enabled iSCSI, re-adding targets, rescan. Same result. Removing partition on 102, Formatted partition on 103 instead. Same result, except flipped. 103 can use storage, 102 can not. Starting Over. Removing all iSCSI Targets on both ESX Boxes, disabling iSCSI, turning off the firewall for iSCSI, rebooting ESX. Then on the MD3000, Removed the Host Group, Removed the Host-to-Virtual Mappings, Restarted the SAN. Followed the Documentation again, same result. Both servers see the storage, but only one server can use it. Disabling and Re-enabling VMware DRS and HA. Same result. Flat-out turning off VMware DRS and HA, and doing the "start over" step to see if maybe that borked it. Same Result. I'm kinda loosing my mind here, Everything i read online says "just partition it and if the ESX boxes can see the targets, it just works".... well crap. Any ideas, any other things to try? Can anyone atleast point me in the right direction? I'm really tired of working from 1am til 4am (our maintenance hours)

  Read the article

• Strange Recurrent Excessive I/O Wait

  - by Chris

  I know quite well that I/O wait has been discussed multiple times on this site, but all the other topics seem to cover constant I/O latency, while the I/O problem we need to solve on our server occurs at irregular (short) intervals, but is ever-present with massive spikes of up to 20k ms a-wait and service times of 2 seconds. The disk affected is /dev/sdb (Seagate Barracuda, for details see below). A typical iostat -x output would at times look like this, which is an extreme sample but by no means rare: iostat (Oct 6, 2013) tps rd_sec/s wr_sec/s avgrq-sz avgqu-sz await svctm %util 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 16.00 0.00 156.00 9.75 21.89 288.12 36.00 57.60 5.50 0.00 44.00 8.00 48.79 2194.18 181.82 100.00 2.00 0.00 16.00 8.00 46.49 3397.00 500.00 100.00 4.50 0.00 40.00 8.89 43.73 5581.78 222.22 100.00 14.50 0.00 148.00 10.21 13.76 5909.24 68.97 100.00 1.50 0.00 12.00 8.00 8.57 7150.67 666.67 100.00 0.50 0.00 4.00 8.00 6.31 10168.00 2000.00 100.00 2.00 0.00 16.00 8.00 5.27 11001.00 500.00 100.00 0.50 0.00 4.00 8.00 2.96 17080.00 2000.00 100.00 34.00 0.00 1324.00 9.88 1.32 137.84 4.45 59.60 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 22.00 44.00 204.00 11.27 0.01 0.27 0.27 0.60 Let me provide you with some more information regarding the hardware. It's a Dell 1950 III box with Debian as OS where uname -a reports the following: Linux xx 2.6.32-5-amd64 #1 SMP Fri Feb 15 15:39:52 UTC 2013 x86_64 GNU/Linux The machine is a dedicated server that hosts an online game without any databases or I/O heavy applications running. The core application consumes about 0.8 of the 8 GBytes RAM, and the average CPU load is relatively low. The game itself, however, reacts rather sensitive towards I/O latency and thus our players experience massive ingame lag, which we would like to address as soon as possible. iostat: avg-cpu: %user %nice %system %iowait %steal %idle 1.77 0.01 1.05 1.59 0.00 95.58 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sdb 13.16 25.42 135.12 504701011 2682640656 sda 1.52 0.74 20.63 14644533 409684488 Uptime is: 19:26:26 up 229 days, 17:26, 4 users, load average: 0.36, 0.37, 0.32 Harddisk controller: 01:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 1078 (rev 04) Harddisks: Array 1, RAID-1, 2x Seagate Cheetah 15K.5 73 GB SAS Array 2, RAID-1, 2x Seagate ST3500620SS Barracuda ES.2 500GB 16MB 7200RPM SAS Partition information from df: Filesystem 1K-blocks Used Available Use% Mounted on /dev/sdb1 480191156 30715200 425083668 7% /home /dev/sda2 7692908 437436 6864692 6% / /dev/sda5 15377820 1398916 13197748 10% /usr /dev/sda6 39159724 19158340 18012140 52% /var Some more data samples generated with iostat -dx sdb 1 (Oct 11, 2013) Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sdb 0.00 15.00 0.00 70.00 0.00 656.00 9.37 4.50 1.83 4.80 33.60 sdb 0.00 0.00 0.00 2.00 0.00 16.00 8.00 12.00 836.00 500.00 100.00 sdb 0.00 0.00 0.00 3.00 0.00 32.00 10.67 9.96 1990.67 333.33 100.00 sdb 0.00 0.00 0.00 4.00 0.00 40.00 10.00 6.96 3075.00 250.00 100.00 sdb 0.00 0.00 0.00 0.00 0.00 0.00 0.00 4.00 0.00 0.00 100.00 sdb 0.00 0.00 0.00 2.00 0.00 16.00 8.00 2.62 4648.00 500.00 100.00 sdb 0.00 0.00 0.00 0.00 0.00 0.00 0.00 2.00 0.00 0.00 100.00 sdb 0.00 0.00 0.00 1.00 0.00 16.00 16.00 1.69 7024.00 1000.00 100.00 sdb 0.00 74.00 0.00 124.00 0.00 1584.00 12.77 1.09 67.94 6.94 86.00 Characteristic charts generated with rrdtool can be found here: iostat plot 1, 24 min interval: http://imageshack.us/photo/my-images/600/yqm3.png/ iostat plot 2, 120 min interval: http://imageshack.us/photo/my-images/407/griw.png/ As we have a rather large cache of 5.5 GBytes, we thought it might be a good idea to test if the I/O wait spikes would perhaps be caused by cache miss events. Therefore, we did a sync and then this to flush the cache and buffers: echo 3 > /proc/sys/vm/drop_caches and directly afterwards the I/O wait and service times virtually went through the roof, and everything on the machine felt like slow motion. During the next few hours the latency recovered and everything was as before - small to medium lags in short, unpredictable intervals. Now my question is: does anybody have any idea what might cause this annoying behaviour? Is it the first indication of the disk array or the raid controller dying, or something that can be easily mended by rebooting? (At the moment we're very reluctant to do this, however, because we're afraid that the disks might not come back up again.) Any help is greatly appreciated. Thanks in advance, Chris. Edited to add: we do see one or two processes go to 'D' state in top, one of which seems to be kjournald rather frequently. If I'm not mistaken, however, this does not indicate the processes causing the latency, but rather those affected by it - correct me if I'm wrong. Does the information about uninterruptibly sleeping processes help us in any way to address the problem? @Andy Shinn requested smartctl data, here it is: smartctl -a -d megaraid,2 /dev/sdb yields: smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net Device: SEAGATE ST3500620SS Version: MS05 Serial number: Device type: disk Transport protocol: SAS Local Time is: Mon Oct 14 20:37:13 2013 CEST Device supports SMART and is Enabled Temperature Warning Disabled or Not Supported SMART Health Status: OK Current Drive Temperature: 20 C Drive Trip Temperature: 68 C Elements in grown defect list: 0 Vendor (Seagate) cache information Blocks sent to initiator = 1236631092 Blocks received from initiator = 1097862364 Blocks read from cache and sent to initiator = 1383620256 Number of read and write commands whose size <= segment size = 531295338 Number of read and write commands whose size > segment size = 51986460 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36556.93 number of minutes until next internal SMART test = 32 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 509271032 47 0 509271079 509271079 20981.423 0 write: 0 0 0 0 0 5022.039 0 verify: 1870931090 196 0 1870931286 1870931286 100558.708 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 16 36538 - [- - -] # 2 Background short Completed 16 36514 - [- - -] # 3 Background short Completed 16 36490 - [- - -] # 4 Background short Completed 16 36466 - [- - -] # 5 Background short Completed 16 36442 - [- - -] # 6 Background long Completed 16 36420 - [- - -] # 7 Background short Completed 16 36394 - [- - -] # 8 Background short Completed 16 36370 - [- - -] # 9 Background long Completed 16 36364 - [- - -] #10 Background short Completed 16 36361 - [- - -] #11 Background long Completed 16 2 - [- - -] #12 Background short Completed 16 0 - [- - -] Long (extended) Self Test duration: 6798 seconds [113.3 minutes] smartctl -a -d megaraid,3 /dev/sdb yields: smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net Device: SEAGATE ST3500620SS Version: MS05 Serial number: Device type: disk Transport protocol: SAS Local Time is: Mon Oct 14 20:37:26 2013 CEST Device supports SMART and is Enabled Temperature Warning Disabled or Not Supported SMART Health Status: OK Current Drive Temperature: 19 C Drive Trip Temperature: 68 C Elements in grown defect list: 0 Vendor (Seagate) cache information Blocks sent to initiator = 288745640 Blocks received from initiator = 1097848399 Blocks read from cache and sent to initiator = 1304149705 Number of read and write commands whose size <= segment size = 527414694 Number of read and write commands whose size > segment size = 51986460 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36596.83 number of minutes until next internal SMART test = 28 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 610862490 44 0 610862534 610862534 20470.133 0 write: 0 0 0 0 0 5022.480 0 verify: 2861227413 203 0 2861227616 2861227616 100872.443 0 Non-medium error count: 1 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 16 36580 - [- - -] # 2 Background short Completed 16 36556 - [- - -] # 3 Background short Completed 16 36532 - [- - -] # 4 Background short Completed 16 36508 - [- - -] # 5 Background short Completed 16 36484 - [- - -] # 6 Background long Completed 16 36462 - [- - -] # 7 Background short Completed 16 36436 - [- - -] # 8 Background short Completed 16 36412 - [- - -] # 9 Background long Completed 16 36404 - [- - -] #10 Background short Completed 16 36401 - [- - -] #11 Background long Completed 16 2 - [- - -] #12 Background short Completed 16 0 - [- - -] Long (extended) Self Test duration: 6798 seconds [113.3 minutes]

  Read the article

• Nagios plugin script not working as expected

  - by Linker3000

  I have modified an off-the-shelf Nagios plugin perl script to (in theory) return a one or zero according to the existence, or not, of a file on a remote linux server. The script runs a remote ssh session and logs in as the nagios user. The remote linux servers have private keys setup for that user, and on the bash command line the script works as expected, but when run as a plugin it always returns '1' (true) even if the file does not exist. Some help with the logic or a comment on why things are not working as expected within Nagios would be appreciated. I'd prefer to use this ssh login method rather than having to install nrpe on all the linux servers. To run from a command line (assuming remote server has a user called nagios with a valid private key): ./check_reboot_required -e ssh -H remote-servers-ip-addr -p 'filename-to-check' -v Ta. #! /usr/bin/perl -w # # # License Information: # This program is free software; you can redistribute it and/or modify # it under the terms of the GNU General Public License as published by # the Free Software Foundation; either version 2 of the License, or # (at your option) any later version. # # This program is distributed in the hope that it will be useful, # but WITHOUT ANY WARRANTY; without even the implied warranty of # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the # GNU General Public License for more details. # # You should have received a copy of the GNU General Public License # along with this program; if not, write to the Free Software # Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. # ############################################################################ use POSIX; use strict; use Getopt::Long; use lib "/usr/lib/nagios/plugins" ; use vars qw($host $opt_V $opt_h $opt_v $verbose $PROGNAME $pattern $opt_p $mmin $opt_e $opt_t $opt_H $status $state $msg $msg_q $MAILQ $SHELL $device $used $avail $percent $fs $blocks $CMD $RMTOS); use utils qw(%ERRORS &print_revision &support &usage ); sub print_help (); sub print_usage (); sub process_arguments (); $ENV{'PATH'}=''; $ENV{'BASH_ENV'}=''; $ENV{'ENV'}=''; $PROGNAME = "check_reboot_required"; Getopt::Long::Configure('bundling'); $status = process_arguments(); if ($status){ print "ERROR: processing arguments\n"; exit $ERRORS{'UNKNOWN'}; } $SIG{'ALRM'} = sub { print ("ERROR: timed out waiting for $CMD on $host\n"); exit $ERRORS{'WARNING'}; }; $host = $opt_H; $pattern = $opt_p; print "Pattern >" . $pattern . "< " if $verbose; alarm($opt_t); #$CMD = "/usr/bin/find " . $pattern . " -type f 2>/dev/null| /usr/bin/wc -l"; $CMD = "[ -f " . $pattern . " ] && echo 1 || echo 0"; alarm($opt_t); ## get cmd output from remote system if (! open (OUTPUT, "$SHELL $host $CMD|" ) ) { print "ERROR: could not open $CMD on $host\n"; exit $ERRORS{'UNKNOWN'}; } my $perfdata = ""; my $state = "3"; my $msg = "Indeterminate result"; # only first line is relevant in this iteration. while (<OUTPUT>) { my $result = chomp($_); $msg = $result; print "Shell returned >" . $result . "< length is " . length($result) . " " if $verbose; if ( $result == 1 ) { $msg = "Reboot required (NB: Result still not accurate)" . $result ; $state = $ERRORS{'WARNING'}; last; } elsif ( $result == 0 ) { $msg = "No reboot required (NB: Result still not accurate) " . $result ; $state = $ERRORS{'OK'}; last; } else { $msg = "Output received, but it was neither a 1 nor a 0" ; last; } } close (OUTPUT); print "$msg | $perfdata\n"; exit $state; ##################################### #### subs sub process_arguments(){ GetOptions ("V" => \$opt_V, "version" => \$opt_V, "v" => \$opt_v, "verbose" => \$opt_v, "h" => \$opt_h, "help" => \$opt_h, "e=s" => \$opt_e, "shell=s" => \$opt_e, "p=s" => \$opt_p, "pattern=s" => \$opt_p, "t=i" => \$opt_t, "timeout=i" => \$opt_t, "H=s" => \$opt_H, "hostname=s" => \$opt_H ); if ($opt_V) { print_revision($PROGNAME,'$Revision: 1.0 $ '); exit $ERRORS{'OK'}; } if ($opt_h) { print_help(); exit $ERRORS{'OK'}; } if (defined $opt_v ){ $verbose = $opt_v; } if (defined $opt_e ){ if ( $opt_e eq "ssh" ) { if (-x "/usr/local/bin/ssh") { $SHELL = "/usr/local/bin/ssh"; } elsif ( -x "/usr/bin/ssh" ) { $SHELL = "/usr/bin/ssh"; } else { print_usage(); exit $ERRORS{'UNKNOWN'}; } } elsif ( $opt_e eq "rsh" ) { $SHELL = "/usr/bin/rsh"; } else { print_usage(); exit $ERRORS{'UNKNOWN'}; } } else { print_usage(); exit $ERRORS{'UNKNOWN'}; } unless (defined $opt_t) { $opt_t = $utils::TIMEOUT ; # default timeout } unless (defined $opt_H) { print_usage(); exit $ERRORS{'UNKNOWN'}; } return $ERRORS{'OK'}; } sub print_usage () { print "Usage: $PROGNAME -e <shell> -H <hostname> -p <directory/file pattern> [-t <timeout>] [-v verbose]\n"; } sub print_help () { print_revision($PROGNAME,'$Revision: 0.1 $'); print "\n"; print_usage(); print "\n"; print " Checks for the presence of a 'reboot-required' file on a remote host via SSH or RSH\n"; print "-e (--shell) = ssh or rsh (required)\n"; print "-H (--hostname) = remote server name (required)"; print "-p (--pattern) = File pattern for find command (default = /var/run/reboot-required)\n"; print "-t (--timeout) = Plugin timeout in seconds (default = $utils::TIMEOUT)\n"; print "-h (--help)\n"; print "-V (--version)\n"; print "-v (--verbose) = debugging output\n"; print "\n\n"; support(); }

  Read the article

• Hibernate unable to instantiate default tuplizer - cannot find getter

  - by ZeldaPinwheel

  I'm trying to use Hibernate to persist a class that looks like this: public class Item implements Serializable, Comparable<Item> { // Item id private Integer id; // Description of item in inventory private String description; // Number of items described by this inventory item private int count; //Category item belongs to private String category; // Date item was purchased private GregorianCalendar purchaseDate; public Item() { } public Integer getId() { return id; } public void setId(Integer id) { this.id = id; } public String getDescription() { return description; } public void setDescription(String description) { this.description = description; } public int getCount() { return count; } public void setCount(int count) { this.count = count; } public String getCategory() { return category; } public void setCategory(String category) { this.category = category; } public GregorianCalendar getPurchaseDate() { return purchaseDate; } public void setPurchasedate(GregorianCalendar purchaseDate) { this.purchaseDate = purchaseDate; } My Hibernate mapping file contains the following: <property name="puchaseDate" type="java.util.GregorianCalendar"> <column name="purchase_date"></column> </property> When I try to run, I get error messages indicating there is no getter function for the purchaseDate attribute: 577 [main] INFO org.hibernate.connection.DriverManagerConnectionProvider - Using Hibernate built-in connection pool (not for production use!) 577 [main] INFO org.hibernate.connection.DriverManagerConnectionProvider - Hibernate connection pool size: 20 577 [main] INFO org.hibernate.connection.DriverManagerConnectionProvider - autocommit mode: false 592 [main] INFO org.hibernate.connection.DriverManagerConnectionProvider - using driver: com.mysql.jdbc.Driver at URL: jdbc:mysql://localhost:3306/home_inventory 592 [main] INFO org.hibernate.connection.DriverManagerConnectionProvider - connection properties: {user=root, password=****} 1078 [main] INFO org.hibernate.cfg.SettingsFactory - RDBMS: MySQL, version: 5.1.45 1078 [main] INFO org.hibernate.cfg.SettingsFactory - JDBC driver: MySQL-AB JDBC Driver, version: mysql-connector-java-5.1.12 ( Revision: ${bzr.revision-id} ) 1103 [main] INFO org.hibernate.dialect.Dialect - Using dialect: org.hibernate.dialect.MySQLDialect 1107 [main] INFO org.hibernate.engine.jdbc.JdbcSupportLoader - Disabling contextual LOB creation as JDBC driver reported JDBC version [3] less than 4 1109 [main] INFO org.hibernate.transaction.TransactionFactoryFactory - Using default transaction strategy (direct JDBC transactions) 1110 [main] INFO org.hibernate.transaction.TransactionManagerLookupFactory - No TransactionManagerLookup configured (in JTA environment, use of read-write or transactional second-level cache is not recommended) 1110 [main] INFO org.hibernate.cfg.SettingsFactory - Automatic flush during beforeCompletion(): disabled 1110 [main] INFO org.hibernate.cfg.SettingsFactory - Automatic session close at end of transaction: disabled 1110 [main] INFO org.hibernate.cfg.SettingsFactory - JDBC batch size: 15 1110 [main] INFO org.hibernate.cfg.SettingsFactory - JDBC batch updates for versioned data: disabled 1111 [main] INFO org.hibernate.cfg.SettingsFactory - Scrollable result sets: enabled 1111 [main] INFO org.hibernate.cfg.SettingsFactory - JDBC3 getGeneratedKeys(): enabled 1111 [main] INFO org.hibernate.cfg.SettingsFactory - Connection release mode: auto 1111 [main] INFO org.hibernate.cfg.SettingsFactory - Maximum outer join fetch depth: 2 1111 [main] INFO org.hibernate.cfg.SettingsFactory - Default batch fetch size: 1 1111 [main] INFO org.hibernate.cfg.SettingsFactory - Generate SQL with comments: disabled 1111 [main] INFO org.hibernate.cfg.SettingsFactory - Order SQL updates by primary key: disabled 1111 [main] INFO org.hibernate.cfg.SettingsFactory - Order SQL inserts for batching: disabled 1112 [main] INFO org.hibernate.cfg.SettingsFactory - Query translator: org.hibernate.hql.ast.ASTQueryTranslatorFactory 1113 [main] INFO org.hibernate.hql.ast.ASTQueryTranslatorFactory - Using ASTQueryTranslatorFactory 1113 [main] INFO org.hibernate.cfg.SettingsFactory - Query language substitutions: {} 1113 [main] INFO org.hibernate.cfg.SettingsFactory - JPA-QL strict compliance: disabled 1113 [main] INFO org.hibernate.cfg.SettingsFactory - Second-level cache: enabled 1113 [main] INFO org.hibernate.cfg.SettingsFactory - Query cache: disabled 1113 [main] INFO org.hibernate.cfg.SettingsFactory - Cache region factory : org.hibernate.cache.impl.NoCachingRegionFactory 1113 [main] INFO org.hibernate.cfg.SettingsFactory - Optimize cache for minimal puts: disabled 1114 [main] INFO org.hibernate.cfg.SettingsFactory - Structured second-level cache entries: disabled 1117 [main] INFO org.hibernate.cfg.SettingsFactory - Echoing all SQL to stdout 1118 [main] INFO org.hibernate.cfg.SettingsFactory - Statistics: disabled 1118 [main] INFO org.hibernate.cfg.SettingsFactory - Deleted entity synthetic identifier rollback: disabled 1118 [main] INFO org.hibernate.cfg.SettingsFactory - Default entity-mode: pojo 1118 [main] INFO org.hibernate.cfg.SettingsFactory - Named query checking : enabled 1118 [main] INFO org.hibernate.cfg.SettingsFactory - Check Nullability in Core (should be disabled when Bean Validation is on): enabled 1151 [main] INFO org.hibernate.impl.SessionFactoryImpl - building session factory org.hibernate.HibernateException: Unable to instantiate default tuplizer [org.hibernate.tuple.entity.PojoEntityTuplizer] at org.hibernate.tuple.entity.EntityTuplizerFactory.constructTuplizer(EntityTuplizerFactory.java:110) at org.hibernate.tuple.entity.EntityTuplizerFactory.constructDefaultTuplizer(EntityTuplizerFactory.java:135) at org.hibernate.tuple.entity.EntityEntityModeToTuplizerMapping.<init>(EntityEntityModeToTuplizerMapping.java:80) at org.hibernate.tuple.entity.EntityMetamodel.<init>(EntityMetamodel.java:323) at org.hibernate.persister.entity.AbstractEntityPersister.<init>(AbstractEntityPersister.java:475) at org.hibernate.persister.entity.SingleTableEntityPersister.<init>(SingleTableEntityPersister.java:133) at org.hibernate.persister.PersisterFactory.createClassPersister(PersisterFactory.java:84) at org.hibernate.impl.SessionFactoryImpl.<init>(SessionFactoryImpl.java:295) at org.hibernate.cfg.Configuration.buildSessionFactory(Configuration.java:1385) at service.HibernateSessionFactory.currentSession(HibernateSessionFactory.java:53) at service.ItemSvcHibImpl.generateReport(ItemSvcHibImpl.java:78) at service.test.ItemSvcTest.testGenerateReport(ItemSvcTest.java:226) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at junit.framework.TestCase.runTest(TestCase.java:164) at junit.framework.TestCase.runBare(TestCase.java:130) at junit.framework.TestResult$1.protect(TestResult.java:106) at junit.framework.TestResult.runProtected(TestResult.java:124) at junit.framework.TestResult.run(TestResult.java:109) at junit.framework.TestCase.run(TestCase.java:120) at junit.framework.TestSuite.runTest(TestSuite.java:230) at junit.framework.TestSuite.run(TestSuite.java:225) at org.eclipse.jdt.internal.junit.runner.junit3.JUnit3TestReference.run(JUnit3TestReference.java:130) at org.eclipse.jdt.internal.junit.runner.TestExecution.run(TestExecution.java:38) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:467) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:683) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.run(RemoteTestRunner.java:390) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.main(RemoteTestRunner.java:197) Caused by: java.lang.reflect.InvocationTargetException at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method) at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39) at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27) at java.lang.reflect.Constructor.newInstance(Constructor.java:513) at org.hibernate.tuple.entity.EntityTuplizerFactory.constructTuplizer(EntityTuplizerFactory.java:107) ... 29 more Caused by: org.hibernate.PropertyNotFoundException: Could not find a getter for puchaseDate in class domain.Item at org.hibernate.property.BasicPropertyAccessor.createGetter(BasicPropertyAccessor.java:328) at org.hibernate.property.BasicPropertyAccessor.getGetter(BasicPropertyAccessor.java:321) at org.hibernate.mapping.Property.getGetter(Property.java:304) at org.hibernate.tuple.entity.PojoEntityTuplizer.buildPropertyGetter(PojoEntityTuplizer.java:299) at org.hibernate.tuple.entity.AbstractEntityTuplizer.<init>(AbstractEntityTuplizer.java:158) at org.hibernate.tuple.entity.PojoEntityTuplizer.<init>(PojoEntityTuplizer.java:77) ... 34 more I'm new to Hibernate, so I don't know all the ins and outs, but I do have the getter and setter for the purchaseDate attribute. I don't know what I'm missing here - does anyone else? Thanks!

  Read the article

• ruby1.9.1 - sqlite3 problem on ubuntu 9.10 x64 (no such file to load -- sqlite3)

  - by doriath

  Hi, I have problem with sqlite3, because it is not working. irb(main):001:0> require 'sqlite3' LoadError: no such file to load -- sqlite3 from (irb):1:in `require' from (irb):1 from /usr/bin/irb:12:in `<main>' I have installed following packages: sudo apt-get install ruby1.9.1-full sudo apt-get install rubygems1.9.1 sudo gem update --system sudo apt-get install sqlite3 libsqlite3-dev sudo gem install sqlite3-ruby sudo apt-get install libopenssl-ruby1.9.1 The applications has following versions: $ ruby --version ruby 1.9.1p243 (2009-07-16 revision 24175) [x86_64-linux] $ sqlite3 --version 3.6.16 $ gem --version 1.3.6 and $ gem list --local *** LOCAL GEMS *** actionmailer (2.3.5) actionpack (2.3.5) activerecord (2.3.5) activeresource (2.3.5) activesupport (2.3.5) ffi (0.6.2) rack (1.0.1) rails (2.3.5) rake (0.8.7) rubygems-update (1.3.6) sqlite3-ruby (1.2.5) What have I missed?

  Read the article

• Should static analysis warnings fail the CI build?

  - by Cara

  Our team is investigating various options for static analysis in our project, and have mixed opinions about whether we want our Continuous Integration build to fail because of warnings from static analysis. The argument against failing the build is that there are often exceptions to the rules, and attempting to work around them just to make the build succeed reduces productivity. A better approach would be to generate reports with the build, and regularly dedicate developer time to addressing the reported issues. The counter-argument is that it is easy for the technical debt to build up if the bugs are not addressed immediately. Also, if the build fails when a potential bug is introduced, the amount of time required to fix it is reduced. What are your thoughts?

  Read the article

• Auto_increment values in InnoDB?

  - by Timmy

  I've been using InnoDB for a project, and relying on auto_increment. This is not a problem for most of the tables, but for tables with deletion, this might be an issue: AUTO_INCREMENT Handling in InnoDB particularly this part: AUTO_INCREMENT column named ai_col: After a server startup, for the first insert into a table t, InnoDB executes the equivalent of this statement: SELECT MAX(ai_col) FROM t FOR UPDATE; InnoDB increments by one the value retrieved by the statement and assigns it to the column and to the auto-increment counter for the table. This is a problem because while it ensures that within the table, the key is unique, there are foreign keys to this table where those keys are no longer unique. The mysql server does/should not restart often, but this is breaking. Are there any easy ways around this?

  Read the article

• Does ActiveCollab subversion integration work with subversion over ssh?

  - by executor21

  I'm trying to setup a repository in an ActiveCollab project. During setup, it reports that the connection tests successfully. However, when I try to actually update the repository, I get the following message: Could not obrain the highest revision number for the given repository. If I try to browse the repository, the following error comes up: Fatal error: Call to a member function getRevision() on a non-object in /u/sites/activecollab/webroot/shared/activecollab/activecollab/application/modules/source/controllers/RepositoryController.class.php on line 357 Is this because of trying to access the repository via svn+ssh plugin rather than http? Or did something happen on the ActiveCollab end? The repository is accessed fine via other means -- only ActiveCollab has the problem.

  Read the article

• Ruby/Rails display general screen when modifications being performed on server

  - by john chan

  I have a ruby on rails app running a server and sometimes it needs to be taken down for updates/etc. As of now, one way I see to have a general display screen during update periods (when the app is down) is to substitute the files within /srv/www/ directory to just have it display a general screen everywhere that the user could possibly navigate to. I also thought of having a central controller file that connects all others (essentially a main) but this seems counter intuitive for rails. There are many external links to these different components of the site that the user could navigate to from outside and I need to make sure that they always receive this general update screen when the app is taken down for a little. I was wondering if anyone had any other ideas.... maybe a library or something like that, I can't seem to find anything online. any suggestions would be appreciated. Thanks

  Read the article

• Extending MySQLi

  - by FRKT

  Hello, I've run into problems extending the MySQLi class. It won't let me add any properties. class MySQLii extends MySQLi { public $database; public function MySQLii($host, $username, $password, $database){ // Initialize MySQLi parent::MySQLi($host, $username, $password, $database); // Save database name $this->database = $database; } } $mysqlii = new MySQLii('localhost', 'root', 'password', 'database'); var_dump($mysqlii); object(MySQLii)#1 (17) { ["affected_rows"]= int(0) ["client_info"]= string(48) "mysqlnd 5.0.5-dev - 081106 - $Revision: 289630 $" ["client_version"]= int(50005) ["connect_errno"]= int(0) ["connect_error"]= NULL ["errno"]= int(0) ["error"]= string(0) "" ["field_count"]= int(0) ["host_info"]= string(42) "MySQL host info: Localhost via UNIX socket" ["info"]= NULL ["insert_id"]= int(0) ["server_info"]= string(6) "5.1.44" ["server_version"]= int(50144) ["sqlstate"]= string(5) "00000" ["protocol_version"]= int(10) ["thread_id"]= int(4019) ["warning_count"]= int(0) } Note the absence of the database property I added in the MySQLii constructor. Am I missing something?

  Read the article

• Why is XHTML1.1 dated *before* XHTML1.0 ? What is the preferred XHTML today?

  - by Cheeso

  I'm not clear on the status of XHTML - v1.0 and v1.1. Can someone explain which is preferred at this point, and why? The specs from w3c say that XHTML 1.1 predates* XHTML 1.0, which is exactly counter-intuitive, to me. http://www.w3.org/TR/xhtml11/ - W3C Recommendation 31 May 2001 http://www.w3.org/TR/xhtml1/ - W3C Recommentation, updated 1 August 2002 Also, I noted earlier today that the latest version of htmltidy emits XHTML 1.0, when I request xhtml. Hmmm....Even though the XHTML 1.1 spec is 9 years old, it's still not supported by mainstream tools. That suggests that XHTML 1.1 is either completely unnecessary or spurious. Which one should I use if I am authoring pages today? What if I am building tools - should I bother to support both? Or do I need only one? Thanks.

  Read the article

• First TDD, Simple 2-tier C# Project - what do I unit test?

  - by Joel

  This is probably a stupid question but my googling isn't finding a satisfactory answer. I'm starting a small project in C#, with just a business layer and a data access layer - strangely, the UI will come later, and I have very little (read:no) concept / control over what it will look like. I would like to try TDD for this project. I'm using Visual Studio 2008 (soon to be 2010), I have ReSharper 5, and nUnit. Again, I want to do Test-Driven Development, but not necessarily the entire XP system. My question is - when and where do I write the first unit test? Do I only test logic before I write it, or do I test everything? It seems counter-productive to test things that have no reason to fail (auto-properties, empty constructors)...but it seems like the "No new code without a failing test" maxim requires this. Links or references are fine (but preferably to online resources, not books - I would like to get started ASAP). Thanks in advance for any guidance!

  Read the article

• Visual SourceSafe: Architecture/Management

  - by Nic

  I was looking for information on how other people with larger teams manage SourceSafe currently. I was looking for recommendations and advice for a new project I was setting up that will allow for a few key things Scalability Manage multiple overlapping releases Geared more around .NET however allows for legacy applications (VB, ASP and VBS) I am really looking for any lessons learned from other teams. I come from a StarTeam background and we used view labels and release labels to manage multiple overlapping projects. View labels geared more towards compiled code and SQL and the revision labels were used for VB/ASP projects. Thank you for any advice and sharing your experience and frustrations with other companies you might have worked with in the past.

  Read the article

• Error running heroku console. can't update heroku

  - by Omnipresent

  When I try to run heroku console I get the following error: user@omnipresent:~/rails/demo$ heroku console ! This version of the heroku gem has been deprecated. ! Please update it by running: gem update heroku When I do the update..it says there is nothing to update! user@omnipresent:~/rails/demo$ gem update heroku Updating installed gems Nothing to update Following are my versions: user@omnipresent:~/rails/demo$ heroku version heroku-gem/1.5.2 user@omnipresent:~/rails/demo$ ruby -v ruby 1.9.1p0 (2009-01-30 revision 21907) [i686-linux] user@omnipresent:~/rails/demo$ rails -v Rails 2.3.5

  Read the article

• Ruby Irb reacts strangely to control keys

  - by eegg

  Hi. I'm (extremely) new to Ruby, having started today. I just moved from my system's Ruby 1.8 installation to Ruby 1.9, compiled from source. In doing so, irb has taken a turn for the worse. It reacts in a most unfriendly way to the non-alphanumeric control keys: UP key prints: ^[[A DOWN key prints: ^[[B DELETE key prints: ^[[3~ ...and so on. The main result of this for me is that I have no access to previously issued commands. Nor does tab-completion work; though none of this seems to be an issue with Wirble - the same happens when I remove my ~/.irbrc. I'm using: Ubuntu 9.10 GNOME Terminal 2.28.1 ruby 1.9.1p376 (2009-12-07 revision 26041) [i686-linux] Irb version 0.9.5 (05/04/13) Any ideas? :(

  Read the article

• Difference between performSelectorInBackground and NSOperation Subclass

  - by AmitSri

  I have created one testing app for running deep counter loop. I run the loop fuction in background thread using performSelectorInBackground and also NSOperation subclass separately. I am also using performSelectorOnMainThread to notify main thread within backgroundthread method and [NSNotificationCenter defaultCenter] postNotificationName within NSOperation subclass to notify main thread for updating UI. Initially both the implementation giving me same result and i am able to update UI without having any problem. The only difference i found is the Thread count between two implementations. The performSelectorInBackground implementation created one thread and got terminated after loop finished and my app thread count again goes to 1. The NSOperation subclass implementation created two new threads and keep exists in the application and i can see 3 threads after loop got finished in main() function. So, my question is why two threads created by NSOperation and why it didn't get terminated just like the first background thread implementation? I am little bit confuse and unable to decide which implementation is best in-terms of performance and memory management. Thanks

  Read the article

• PerformanceCounters on .NET 4.0 & Windows 7

  - by scott

  I have a program that works fine on VS2008 and Vista, but I'm trying it on Windows 7 and VS2010 / .NET Framework 4.0 and it's not working. Ultimately the problem is that System.Diagnostics.PerformanceCounterCategory.GetCategories() (and other PerformanceCounterCategory methods) is not working. I'm getting a System.InvalidOperationException with the message "Cannot load Counter Name data because an invalid index '' was read from the registry." I can reproduce this with the very simple program shown below: class Program { static void Main(string[] args) { foreach (var pc in System.Diagnostics.PerformanceCounterCategory.GetCategories()) { Console.WriteLine(pc.CategoryName); } } } I did make sure I'm running the program as an admin. It doesn't matter if I run it with VS/Debugger attached or not. I don't have another machine with Windows 7 or VS2010 to test it on, so I'm not sure which is complicating things here (or both?). It is Windows 7 x64 and I've tried forcing the app to run in both x32 and x64 but get the same results.

  Read the article

• Linux Kernel Module - Creating proc file - proc_root undeclared error

  - by Zach

  I copy and paste code from this URL for creating and reading/writing a proc file using a kernel module and get the error that proc_root is undeclared. This same example is on a few sites so I assume it works. Any ideas why I'd get this error? Does my makefile need something different. Below is my makefile as well: Example code for a basic proc file creation (direct copy and paste to get initial test done): http://tldp.org/LDP/lkmpg/2.6/html/lkmpg.html#AEN769 Makefile I'm using: obj-m := counter.o KDIR := /MY/LINUX/SRC PWD := $(shell pwd) default: $(MAKE) ARCH=um -C $(KDIR) SUBDIRS=$(PWD) modules

  Read the article

• Maintain set of local commits working with git-svn

  - by benizi

  I am using git to develop against a project hosted in subversion, using git-svn: git svn clone svn://project/ My general workflow has been to repeatedly edit-and-commit on the master branch, then commit to the svn repository via: git stash git svn dcommit git stash apply One of the local modifications that 'stash' command is preserving, that I don't want to commit to the svn repository, is a changed database connection string. What's the most convenient way to keep this local change without the extra 'stash' steps? I suspect that something like 'stash' or 'quilt' is what I'm looking for, but I'm still new enough to git that I think I'm missing some terminology that would lead to the exact incantation. Update: The only solution I found that seems to avoid the git stash + git-svn action + git stash apply series was to update the git-svn ref manually: (check in local-only change to 'master', then...) $ cat .git/refs/master > .git/refs/remote/git-svn $ git svn fetch (with at least one new SVN revision) And that leaves the local-only commit as a weird (probably unsafe) commit between two svn revisions.

  Read the article

< Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >