Search Results

Search found 14443 results on 578 pages for 'virtual keyboard'.

Page 64/578 | < Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >

• What are the advantages and disadvantages of the various virtual machine image formats?

  - by Matt

  Xen and Virtualbox etc both support a range of different virtual machine image formats. These are: vmdk, vdi, qcow & qcow2, hdd & vhd. Without any bias toward a particular product, I'm wanting to know what are the advantages and disadvantages of the various formats both from a features perspective, robustness and speed? One piece of info I discovered in a forum post was this: "The major difference is that VDI uses relatively large blocks (1MB) when growing an image, and thus has less overhead for block pointers etc. but isn't ultimately space efficient in the sense that if a single byte is non-zero in such a 1MB block the entire space is used. VMDK in contrast uses 64K blocks, and thus has more management overhead and generally a bit less disk space consumption What offsets this is that VDI is more efficient when it comes to snapshots." You might be thinking, I want to know this because I want to know which format to choose? Not exactly, I'm developing some software which utilises these formats and want to support one or more of them. Simplicity, large disks and ease of development are my main drivers.

  Read the article

• Does migrating 2 domain controllers between 2 datacentre requires both virtual machines to be shut down at the same time?

  - by Imagineer

  I was attempting to migrate 2 virtual machines that are domain controllers between 2 datacentres running ESX 3.5 and ESX 4.1. I was advised to shut down both domain controller at the same time during the migration process. This is to avoid USN Rollback and other replication issues. The following are the steps that I was planning to perform: 1. Shutdown both DC. 2. Copy both VMs files across to new datacentre using Veeam FastSCP (connection to both vCentre through IP address instead of hostname) 3. Power them up at new datacentre. 4. Configure Network interface/DNS/DHCP for both DCs in new datacentre I have tried to use Veeam FastSCP rather than VMware Standalone Converter is because its copying rather than converting. Someone also suggested that I use backup and restore app like Veeam backup and replication software. Sounds like a simple job, but after shutting down both DCs, the transfer rate using FastSCP is so slow registering only 1KB/s as oppose to the normal 1MB/s (or more). When that attempt to transfer failed, I tried to cold clone both DCs resulted in the both ESX hosts get disconnected. I have tried troubleshooting by referring to this - VMware KB - Diagnosing an ESX Server that is Disconnected or Not Responding in VirtualCenter It seems that the DNS being down is the caused of all unusual occurrence. The moment I powered up the DCs via VMware console command, the ESX host were able to connect to the vCentre again. How can I avoid such a pitfall again? Am I doing it correctly? Any help would be greatly appreciated! Thank you.

  Read the article

• Azure Virtual Machines - what fault tolerance do they provide?

  - by Borek

  We are thinking about moving our virtual machines (Hyper-V VHDs) to Windows Azure but I haven't found much about what kind of fault tolerance that infrastructure provides. When I run VHD in Azure, I've got two questions: Is my VHD and all the data in it safe? I think that uploaded VHDs use the "Storage" infrastructure so they should be automatically replicated to multiple disks and geographically distributed but should I still make a full-image backup just to be safe? (Note that of course I will be backing up the actual data inside VMs that I care about; I just want to know if there is a chance greater than 0.0000001% that one day I will receive an email from Microsoft telling me that my VM is gone and that I should create or restore it from scratch). Do I need to worry about other things regarding the availability of my VMs? I mean, when I have an on-premise server I need to worry about the hardware itself, about the host operating system, what would happen if my router failed, if my Hyper-V's C: drive failed etc. Am I right in thinking that with Azure, their infrastructure takes care of all of this? Thanks.

  Read the article

• nginx problem accessing virtual hosts

  - by Sc0rian

  I am setting up nginx as a reverse proxy. The server runs on directadmin and lamp stack. I have nginx running on port 81. I can access all my sites (including virtual ips) on the port 81. However when I forward the traffic from port 80 to 81, the virtual ips have a message saying "Apache is running normally". Server IPs are fine, and I can still access virtual IP's on 81. [root@~]# netstat -an | grep LISTEN | egrep ":80|:81" tcp 0 0 <virtual ip>:81 0.0.0.0:* LISTEN tcp 0 0 <virtual ip>:81 0.0.0.0:* LISTEN tcp 0 0 <serverip>:81 0.0.0.0:* LISTEN tcp 0 0 :::80 :::* LISTEN apache 24090 0.6 1.3 29252 13612 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24092 0.9 2.1 39584 22056 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24096 0.2 1.9 35892 20256 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24120 0.3 1.7 35752 17840 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24495 0.0 1.4 30892 14756 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24496 1.0 2.1 39892 22164 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24516 1.5 3.6 55496 38040 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24519 0.1 1.2 28996 13224 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24521 2.7 4.0 58244 41984 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24522 0.0 1.2 29124 12672 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24524 0.0 1.1 28740 12364 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24535 1.1 1.7 36008 17876 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24536 0.0 1.1 28592 12084 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24537 0.0 1.1 28592 12112 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24539 0.0 0.0 0 0 ? Z 18:35 0:00 [httpd] <defunct> apache 24540 0.0 1.1 28592 11540 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24541 0.0 1.1 28592 11548 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL root 24548 0.0 0.0 4132 752 pts/0 R+ 18:35 0:00 egrep apache|nginx root 28238 0.0 0.0 19576 284 ? Ss May29 0:00 nginx: master process /usr/local/nginx/sbin/nginx -c /usr/local/nginx/conf/nginx.conf apache 28239 0.0 0.0 19888 804 ? S May29 0:00 nginx: worker process apache 28240 0.0 0.0 19888 548 ? S May29 0:00 nginx: worker process apache 28241 0.0 0.0 19736 484 ? S May29 0:00 nginx: cache manager process here is my nginx conf: cat /usr/local/nginx/conf/nginx.conf user apache apache; worker_processes 2; # Set it according to what your CPU have. 4 Cores = 4 worker_rlimit_nofile 8192; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] ' '"$request" $status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; server_tokens off; access_log /var/log/nginx_access.log main; error_log /var/log/nginx_error.log debug; server_names_hash_bucket_size 64; sendfile on; tcp_nopush on; tcp_nodelay off; keepalive_timeout 30; gzip on; gzip_comp_level 9; gzip_proxied any; proxy_buffering on; proxy_cache_path /usr/local/nginx/proxy_temp levels=1:2 keys_zone=one:15m inactive=7d max_size=1000m; proxy_buffer_size 16k; proxy_buffers 100 8k; proxy_connect_timeout 60; proxy_send_timeout 60; proxy_read_timeout 60; server { listen <server ip>:81 default rcvbuf=8192 sndbuf=16384 backlog=32000; # Real IP here server_name <server host name> _; # "_" is for handle all hosts that are not described by server_name charset off; access_log /var/log/nginx_host_general.access.log main; location / { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://<server ip>; # Real IP here client_max_body_size 16m; client_body_buffer_size 128k; proxy_buffering on; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 120; proxy_buffer_size 16k; proxy_buffers 32 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; } location /nginx_status { stub_status on; access_log off; allow 127.0.0.1; deny all; } } include /usr/local/nginx/vhosts/*.conf; } here is my vhost conf: # cat /usr/local/nginx/vhosts/1.conf server { listen <virt ip>:81 default rcvbuf=8192 sndbuf=16384 backlog=32000; # Real IP here server_name <virt domain name>.com ; # "_" is for handle all hosts that are not described by server_name charset off; access_log /var/log/nginx_host_general.access.log main; location / { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://<virt ip>; # Real IP here client_max_body_size 16m; client_body_buffer_size 128k; proxy_buffering on; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 120; proxy_buffer_size 16k; proxy_buffers 32 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; } }

  Read the article

• Can I set up two computers up with the same monitors/keyboard/mouse in a modular way?

  - by CodeJunkie

  I have a desktop computer computer (running Windows 7), and a laptop (running OSX Mountain Lion, and maybe Ubuntu 12 eventually). When the laptop is at home, I want both the desktop and the laptop to use the same (2+) monitors, the keyboard, and the mouse (or mice, if I add a track pad). I know about KVM switches, but I want something more complicated. I like to use Synergy to use both computers with one keyboard and mouse at the same time. Synergy requires that the keyboard and mouse be connected to one computer (the server), which shares them with other computers (clients) over wifi. the issue is that when one computer isn't logged in, Synergy doesn't work on it. Sometimes, I want my laptop to be the server (physically connected to the keyboard and mouse), and sometimes I want my desktop to be the server. This means that I need the keyboard/mouse/other USB devices to be able to switch computers without me playing musical plugs. To complicate things further, I don't always want the same desktop set up in terms of monitors. Sometimes, I want the desktop to have both monitors. Other times, I want the laptop to control both monitors. Sometimes I want the desktop to control one monitor, and the laptop to control the other. In any case, the keyboard and mouse need to be able to be physically connected to either computer without lots of fussing with plugs. This breaks down to at least this set of possible combinations: Desktop controls both monitors, and has a physical connection to keyboard and mouse Laptop controls both monitors, and has a physical connection to keyboard and mouse Desktop and laptop each control a monitor, but the desktop has a physical connection to the keyboard and mouse (which it shares with the laptop via wifi) Desktop and laptop each control a monitor, but the laptop has a physical connection to the keyboard an mouse (which it shares with the desktop via wifi) some usb devices connected via a usb hub need to be able to switch physical connection between computers, ideally without the keyboard and mouse switching computer connection There may be other combinations, but these are the main ones at the moment. Basically, I need a KVM switch which allows me to switch individual monitors/keyboard/mouse/usb hub between computers independently of each other, or a better solution. How can I set two computers up with the same monitors/mice/keyboard/usb hub without having to switch everything to one computer or the other all at the same time?

  Read the article

• Is there such a thing as a virtual COM port receipt printer?

  - by Blorgbeard

  I'm debugging some code that writes directly to a COM port in order to print receipts on a receipt printer. The printer model is something like an Epsom TM-88. Instead of printing reams of thermal paper while debugging this code, it would be nice if I could use some kind of virtual printer. Like PDFCreator or FinePrint, but with a virtual COM port instead of a virtual windows printer. Does anyone know of such a thing? Edit: The code sends control characters to get bold text and other formatting. I'd like to see this in the output if possible.

  Read the article

• Backtick (Grave accent) button sticking

  - by Scott Lemmon

  I have Ubuntu 12.04 running in a Virtual Box virtual machine, on my Windows 7 32bit system. It has been working great, except that the backtick/tilde button sticks(not physically). When I hit the backtick button it keeps repeating until another input button is pressed. So if I press the spacebar while the backtick is repeating, it stops, but if I press the shift while it is repeating, the backtick turns into a tilde, and the tilde keeps repeating until I release the shift key (at which point it's a backtick again and keeps repeating). This sticking behavior only happens with the backtick key, and only in my Ubuntu virtualization, never in windows. I've tried both my laptop's keyboard and an external USB keyboard and the problem happens on both. Both keyboards I've tried are Japanese 106/109 key layout, but I'm using them with a English(US) 101 profile. When I refer to the backtick key above, I mean where it is on the US layout. If I use the Japanese profile, the key in that location (the US backtick location) still sticks, but its no longer mapped as the backtick key. Any thoughts as to what might be causing this and possible solutions? I've searched a lot, but have not found any help so far. Any help is greatly appreciated.

  Read the article

• How to change CapsLock key to produce "a"?

  - by Pit

  While typing I often hit the CapsLock key instead of the a key. (QWERTZU keyboard) This is quite annoying because the moment I realise that I hit the wrong key, I will have to delete multiple character/lines of text an rewrite them in the right form. I am searching for a way to prevent this. I have found a possibility to disable the CapsLock key in Keyboard Layout Options. But this would in my case mean that instead of writing an a I would write nothing. Positive - I don't have to rewrite a whole line, but only one character Negative - It's not that obvious that I hit the wrong key, as a missing character is not perceivable as an upper-case line of text. I would therefore prefer a possibility to map CapsLock to a . Thus when hitting CapsLock an a character would be written. Positive - If I hit CapsLock instead of a I get the output I actually wanted to type. Negative - If I hit CapsLock in any other context I will get an a character. As I don't ever intentionally use the CapsLock key this would not really pose a problem. (I think, or does it?) My Question: So how do I change to a ? And is there any case where this could be dangerous/provoke unwanted behaviour?

  Read the article

• If statement causing xna sprites to draw frame by frame

  - by user1489599

  I’m a bit new to XNA but I wanted to write a simple program that would fire a cannon ball from a cannon at a 45 degree angle. It works fine outside of my keyboard i/o if statement, but when I encapsulate the code around an if statement checking to see if the user hits the space bar, the sprite will draw one frame at a time every time the space bar is hit. This is the code in question if (currentKeyboardState.IsKeyUp(Keys.Space) && previousKeyboardState.IsKeyDown(Keys.Space) && !skullBall.Alive) { //works outside the keyboard input if statement //{ skullBall.Position = cannon.Position; skullBall.DeltaY = -(float)(Math.Sin(MathHelper.ToRadians(45)) * 50/*39.7577*/ * time + 0.5 * (gravity * (time * time))); skullBall.DeltaX = (float)(Math.Cos(MathHelper.ToRadians(45)) * 50/*39.7577*/ * time); skullBall.Alive = true; //} } The skull ball represents the cannon ball and the cannon is just the starting point. DeltaX and DeltaY are the values I’m using to update the cannon balls position per update. I know it's dumb to have the cannon ball start at the cannons position every time the update is called but it’s not really noticeable right now. I was wondering if after examining my code, if anyone noticed any errors that would cause the sprite to display frame by frame instead of drawing it as a full animation of the cannon ball leaving the cannon and moving from there.

  Read the article

• Fn key sticks down

  - by Oli

  Just bought my significant other a shiny new Samsung Q330 13" netbook, stuck an OCZ Agility in it and installed Maverick. Just as a quick aside, this is a devastating combination. Graphics work perfectly and it cold-boots to desktop in about 7 seconds. Very quick. But (common to laptops) I've got a couple of problems. I'll start with the most problematic and start a new thread for the other. Like a lot of laptops, there is a Fn (function) modifier to allow some keys to have another purpose. When I tried to alter the brightness of the screen by tapping Fn+Down, it worked but kept on going until it was as dim as it could go. I tapped Fn+Up and it went to the other extreme. After that the entire keyboard ceases to work properly because the Fn modifier appears to be locked. Additionally, and as a direct side effect, I think, clicking on things doesn't result in a standard result. It's as if control is being held. A reboot is the only thing that seems to fix these problems. This isn't a problem if you don't touch the Fn key but as there are two of them on the keyboard, an accident is going to happen sooner than later, requiring a reboot (and probably some data loss). I don't have a lot of experience with laptops (I prefer my hulking great desktop) so this isn't my area of expertise. I'm open to all suggestions, even disabling the two Fn keys until we can find a better solution.

  Read the article

• XNA: How to make the Vaus Spacecraft move left and right on directional keys pressed?

  - by Will Marcouiller

  I'm currently learning XNA per suggestion from this question's accepted answer: Where to start writing games, any tutorials or the like? I have then installed everything to get ready to work with XNA Game Studio 4.0. General Objective Writing an Arkanoid-like game. I want to make my ship move when I press either left or right keys. Code Sample protected override void Update(GameTime gameTime) { // Allows the game to exit if (GamePad.GetState(PlayerIndex.One).Buttons.Back == ButtonState.Pressed) this.Exit(); // TODO: Add your update logic here #if WINDOWS if (Keyboard.GetState().IsKeyDown(Keys.Escape)) this.Exit(); else { if (Keyboard.GetState().IsKeyDown(Keys.Left)) MoveLeft(gameTime); } #endif // Move the sprite around. BounceEnergyBall(gameTime); base.Update(gameTime); } void MoveLeft(GameTime gameTime) { // I'm not sure how to play with the Vector2 object and its position here!... _vausSpacecraftPos /= _vausSpacecraftSpeed.X; // This line makes the spacecraft move diagnol-top-left. } Question What formula shall I use, or what algorithm shall I consider to make my spaceship move as expected left and right properly? Thanks for your thoughts! Any clue will be appreciated. I am on my learning curve though I have years of development behind me (already)!

  Read the article

• virtual column for drop down in the ruby on rails.

  - by pramod

  How to place a drop down for the virtual column, in the ruby on rails. The virutal column does not exist in my table , but I want to get the value from the drop down ,when user saves the data. for example, product_price is a virtual column , which doesn't exist in my database table. But I would like to have a dropdown, with product price to be displayed from another table. And when user selects the product_price, the selected product_price should be gettable in an object as self.product_price. Virtual column for labels is working fine, but for drop down its not working for me..any info woud be Thankful...

  Read the article

• Control convention for circular movement?

  - by Christian

  I'm currently doing a kind of training project in Unity (still a beginner). It's supposed to be somewhat like Breakout, but instead of just going left and right I want the paddle to circle around the center point. This is all fine and dandy, but the problem I have is: how do you control this with a keyboard or gamepad? For touch and mouse control I could work around the problem by letting the paddle follow the cursor/finger, but with the other control methods I'm a bit stumped. With a keyboard for example, I could either make it so that the Left arrow always moves the paddle clockwise (it starts at the bottom of the circle), or I could link it to the actual direction - meaning that if the paddle is at the bottom, it goes left and up along the circle or, if it's in the upper hemisphere, it moves left and down, both times toward the outer left point of the circle. Both feel kind of weird. With the first one, it can be counter intuitive to press Left to move the paddle right when it's in the upper area, while in the second method you'd need to constantly switch buttons to keep moving. So, long story short: is there any kind of existing standard, convention or accepted example for this type of movement and the corresponding controls? I didn't really know what to google for (control conventions for circular movement was one of the searches I tried, but it didn't give me much), and I also didn't really find anything about this on here. If there is a Question that I simply didn't see, please excuse the duplicate.

  Read the article

• Should we create Virtual Machine environment so a consultant can develop in similiar environment?

  - by ChrisNel52

  This is a large project and currently there are only 3 developers working on it. We have some money in the budget to contract development help from a software consulting firm. However, because the location of our business it would be beneficial if the consultant could do their development off-site. Also, our company policy doesn't allow contract help to VPN into our network, so that is not an option. My question is, would it be a good idea to create a Virtual Machine that copies our internal environment (particularly our database and WCF service) and give the consultant the Virtual Machine image so that they can replicate the environment at their place of work? I haven't worked much with Virtual Machines, so I'm not sure if this is a good idea or if there are huge obstacles that I'm not thinking of. If anyone has ever done anything like this, it would be great to hear the pros/cons. Any help would be appreciated.

  Read the article

• How would I write a virtual CD/DVD burner that would allow programs that burn to write to ISO?

  - by Ryan

  I want to write an app that will allow a program like iTunes which normally will recognize a DVD/CD burner to recognize a virtual one and then write to it creating an ISO. I would guess to use C/C++... can someone point me in the right direction as to how this can be done? Basically it would be a virtual CD/DVD burner that would output an ISO file to the hard drive. I want to do this for both the usefulness of it as well as the challenge, just need an idea of how to approach it, have no idea how to write virtual hardware.

  Read the article

• Just how much do I want to make virtual?

  - by Alex

  I am writing an abstract superclass where literally every method is going to be overridden. There is some default functionality I could implement, but most of the time it's enough to leave the implementation to the subclass writer. Since just about every method is going to be overwritten, how much should I make virtual and how much should I just leave as regular methods? In the current incarnation, everything is virtual, but I still haven't let this loose to anyone to use, so the design is flexible. What advantages/disadvantages are there to virtual functions? Links to good reading material about this would be appreciated.

  Read the article

• How to override virtual function in good style? [C++]

  - by Knowing me knowing you

  Hi, guys I know this question is very basic but I've met in few publications (websites, books) different style of override virtual function. What I mean is: if I have base class: class Base { public: virtual void f() = 0; }; in some publications I saw that to override this some authors would just say: void f(); and some would still repeat the virtual keyword before void. Which form of overwriting is in good style? Thank you for your answers.

  Read the article

• IP failover with 2 nodes on different subnet: cannot ping virtual IP from second node?

  - by quanta

  I'm going to setup redundant failover Redmine: another instance was installed on the second server without problem MySQL (running on the same machine with Redmine) was configured as master-master replication Because they are in different subnet (192.168.3.x and 192.168.6.x), it seems that VIPArip is the only choice. /etc/ha.d/ha.cf on node1 logfacility none debug 1 debugfile /var/log/ha-debug logfile /var/log/ha-log autojoin none warntime 3 deadtime 6 initdead 60 udpport 694 ucast eth1 node2.ip keepalive 1 node node1 node node2 crm respawn /etc/ha.d/ha.cf on node2: logfacility none debug 1 debugfile /var/log/ha-debug logfile /var/log/ha-log autojoin none warntime 3 deadtime 6 initdead 60 udpport 694 ucast eth0 node1.ip keepalive 1 node node1 node node2 crm respawn crm configure show: node $id="6c27077e-d718-4c82-b307-7dccaa027a72" node1 node $id="740d0726-e91d-40ed-9dc0-2368214a1f56" node2 primitive VIPArip ocf:heartbeat:VIPArip \ params ip="192.168.6.8" nic="lo:0" \ op start interval="0" timeout="20s" \ op monitor interval="5s" timeout="20s" depth="0" \ op stop interval="0" timeout="20s" \ meta is-managed="true" property $id="cib-bootstrap-options" \ stonith-enabled="false" \ dc-version="1.0.12-unknown" \ cluster-infrastructure="Heartbeat" \ last-lrm-refresh="1338870303" crm_mon -1: ============ Last updated: Tue Jun 5 18:36:42 2012 Stack: Heartbeat Current DC: node2 (740d0726-e91d-40ed-9dc0-2368214a1f56) - partition with quorum Version: 1.0.12-unknown 2 Nodes configured, unknown expected votes 1 Resources configured. ============ Online: [ node1 node2 ] VIPArip (ocf::heartbeat:VIPArip): Started node1 ip addr show lo: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet 192.168.6.8/32 scope global lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever I can ping 192.168.6.8 from node1 (192.168.3.x): # ping -c 4 192.168.6.8 PING 192.168.6.8 (192.168.6.8) 56(84) bytes of data. 64 bytes from 192.168.6.8: icmp_seq=1 ttl=64 time=0.062 ms 64 bytes from 192.168.6.8: icmp_seq=2 ttl=64 time=0.046 ms 64 bytes from 192.168.6.8: icmp_seq=3 ttl=64 time=0.059 ms 64 bytes from 192.168.6.8: icmp_seq=4 ttl=64 time=0.071 ms --- 192.168.6.8 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3000ms rtt min/avg/max/mdev = 0.046/0.059/0.071/0.011 ms but cannot ping virtual IP from node2 (192.168.6.x) and outside. Did I miss something? PS: you probably want to set IP2UTIL=/sbin/ip in the /usr/lib/ocf/resource.d/heartbeat/VIPArip resource agent script if you get something like this: Jun 5 11:08:10 node1 lrmd: [19832]: info: RA output: (VIPArip:stop:stderr) 2012/06/05_11:08:10 ERROR: Invalid OCF_RESK EY_ip [192.168.6.8] http://www.clusterlabs.org/wiki/Debugging_Resource_Failures Reply to @DukeLion: Which router receives RIP updates? When I start the VIPArip resource, ripd was run with below configuration file (on node1): /var/run/resource-agents/VIPArip-ripd.conf: hostname ripd password zebra debug rip events debug rip packet debug rip zebra log file /var/log/quagga/quagga.log router rip !nic_tag no passive-interface lo:0 network lo:0 distribute-list private out lo:0 distribute-list private in lo:0 !metric_tag redistribute connected metric 3 !ip_tag access-list private permit 192.168.6.8/32 access-list private deny any

  Read the article

• Strict security and virtual host isolation with Nginx?

  - by Hach-Que

  I currently have an Apache web server set up under which each virtual host is isolated using HTTPD-ITK and the AppArmor module. Each virtual host's workers are setuid/setgid by the server and are then placed in an AppArmor profile. I'm looking to use Nginx but I can't find any documentation on setting it up so that rather than the worker processes being shared between all virtual hosts, worker processes are per virtual host (and thus can be setuid / setgid). Is there any way to do this under Nginx?

  Read the article

• How to deal with 100's or 1000's of virtual hosts

  - by anton

  I am curious to know how services such as heroku manage 1000's of virtual hosts - ie if you create a web site/app, and put it up on these services, you get your own virtual host name - foo.heroku.com etc (the same applies to many other sites that have vanity URLs). I know with various web servers and proxies you can configure as many virtual hosts as you want - but there must be some upper limit to this ? Do they programmatically add virtual hosts - perhaps spreading the load? Or are there other solutions.

  Read the article

• How to retrieve virtual machines from a pool via API in oVirt (RHEV)

  - by FerCa

  In oVirt (Red Hat Enterprise Virtualization) you can create a Virtual Machines Pool to allow your users to retrieve virtual machines from this pool. I found how a user, in the RHEV User Portal, can request a Virtual Machine from the pool, this is explained here: https://access.redhat.com/knowledge/docs/en-US/Red_Hat_Enterprise_Virtualization/3.0/html/Evaluation_Guide/Evaluation_Guide-Allocate_VM.html The thing is that i will need to retrieve virtual machines from the pool with the REST API and, after reading the documentation (https://access.redhat.com/knowledge/docs/en-US/Red_Hat_Enterprise_Virtualization/3.0/html-single/REST_API_Guide/index.html) I cant found the way to do this.

  Read the article

• Upgrade Ubuntu linux-virtual on EC2

  - by James Ward

  I have an Ubuntu 10.10 EBS boot server on EC2. There are new updates available for it: linux-image-virtual linux-virtual Is it even ok to upgrade those packages on an EC2 server? When I do try to upgrade them I get: The following packages have been kept back: linux-image-virtual linux-virtual Should I do a dist-upgrade or something to force it? Will my instance be able to be rebooted?

  Read the article

• Can VHD from Virtual PC 2007 be mounted under Virtual Server 2005 R2?

  - by SteveM82

  I have a virtual hard disk file (VHD) created using Microsoft Virtual PC 2007. Can this file be copied to a host running Microsoft Virtual Server 2005 R2 and be used as the basis for creating a new virtual machine? Essentially, are the VHD file formats between the two products compatible, or do I need to create a new VHD from scratch? Thanks.

  Read the article

• How to prevent virtual machines's copy

  - by Florent

  I'll have to deploy virtual machines on demo laptops, which will use Vmware player, but I've got some security concerns, as some data stored in the virtual machines are a bit sensitive. Is there a way to prevent the copy of these virtual machines ? Are the virtual hard drives encrypted, and if not is there a way to encrypt them ? In short, is there a way to lock down everything so that nobody could copy and or use these VMs in another computer ?

  Read the article

• vmdk to live cd - VMware vmxnet virtual NIC driver Kernel panic

  - by ronalchn

  Task I am trying to convert a virtual machine to a live CD. Specifically, the virtual machine I am trying to convert is the IOI 2013 Competition Environment. In this task, I am aided by a guide Converting a virtual disk image: VDI or VMDK to an ISO you can distribute. Symptoms However, after getting through all the instructions, the live CD causes a kernel panic on boot on bare metal. In particular, the screen shows: [0.737348] cdrom: Uniform CD-ROM driver Revision: 3.20 [0.737503] sr 3:0:0:0: >Attached scsi CD-ROM sr0 [0.737638] sr 3:0:0:0: >Attached scsi generic sg2 type 5 [0.737771] Freeing unused kernel memory: 756k freed [0.738093] Write protecting the kernel text: 5960k [0.738155] Write protecting the kernel read-only data: 2424k [0.738224] NX-protecting the kernel data: 4280k Loading, please wait... [0.752252] udevd[100]: starting version 175 [0.768708] VMware vmxnet3 virtual NIC driver - version 1.1.29.0-k-NAPI [0.781204] VMware PVSCSI driver - version 1.0.2.0-k [0.789555] VMware vmxnet virtual NIC driver [0.799356] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200 [0.799356] [0.799472] Pid: 1, comm: init Tainted: G 0 3.5.0-17-generic #28-Ubuntu [0.799549] Call Trace: [0.799603] [<c15bf0ec>] panic+0x81/0x17b [0.799654] [<c104a6a5>] do_exit+0x745/0x7a0 [0.799707] [<c104a9a4>] do_group_exit+0x34/0xa0 [0.799760] [<c104aa28>] sys_exit_group+0x18/0x20 [0.799813] [<c15cff5f>] sysenter_do_call+0x12/0x28 Possible problem I suspect that the problem is the VMware vmxnet virtual NIC driver - however, I do not know how I can uninstall it, and possibly install one for a bare metal machine. If anyone knows which packages needs installing/uninstalling at the .rootfs/ chroot directory stage, please let me know. Details on procedure Do note that after importing the .ova file into Virtualbox, the virtual machine is stored as a .vmdk file already, and not a .vdi file. I would like to point out some results of the procedure followed in case of any questions. This is after extracting the filesystem from the .raw file to the .rootfs/ directory mentioned in the blog. I changed the filesystem table as mentioned in the blog, then looked at the possible "kernel optimized for virtualization". However, I found that linux-image-generic was already installed. Also, when running the command dpkg-query --showformat='${Package}\n' -W 'vmware-tools*' (or dpkg-query --showformat='${Package}\n' -W '*-virtual'), no packages were found. Thus, I did not find any virtualization specific packages. I proceeded to generate the iso following the steps in the blog, and burned it to a DVD.

  Read the article

< Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >