Search Results

Search found 19625 results on 785 pages for 'local groups'.

Page 648/785 | < Previous Page | 644 645 646 647 648 649 650 651 652 653 654 655  | Next Page >

• E-mail duplication problem

  - by Gavin Osborn

  I have taken out a hosting agreement with a well respected hosting provider for a couple of internet facing servers. We have deployed several applications to these servers which send various e-mails back to us for reporting purposes. Context: Each server runs Windows Server 2003 R2 with the IIS 6.0 SMTP service installed. Each application is configured to use the local instance of IIS to send e-mails. The external IP address of each server is mapped to a particular domain eg: server1.mydomain.com server2.mydomain.com These e-mails are sent from a company domain name and not the domain name of the hosted servers (eg: [email protected]) Symptoms: A small number (<1%) of e-mails sent from these applications appear to be duplicated. These are exact duplicate in terms of both content and message headers. The Fix: I contacted my hosting provider and they told me this was a common problem & instructed me to: Change the HELO response of your mail server service to a FQDN (server1.mydomain.com && server2.mydomain.com) Create a DNS A record that resolves the FQDN of your mail server to the primary IP address of your sending mail server. Create a PTR record that resolves your primary IP address back to your mail server's FQDN In the sending domain's (mycompanydomain.com) DNS zone file, add the appropriate SPF record for your hosted servers. eg: v=spf1 a mx include:mydomain -all The Problem Continues: I made all of the changes as prescribed above, I was a little hesitant because these steps seemed to suggest they were more for stopping your messages getting blocked than they were for stopping them from being duplicated - but I am certainly no expert in these matters. It has been 5 days since I applied this fix and the problem still persists. I am certain that these problems are not a bug in the software because they are 4 different applications installed on 2 different servers, all of whom are exhibiting this strange behaviour. This behaviour has also not been seen in our UAT environment. Were my hosts correct to suggest this fix? If not, does anyone know what could be the cause of this problem? Many Thanks

  Read the article

• Unable to record using Jmeter

  - by krish

  Hi, I am trying to record a http web page using Jmeter 2.3.3 version.I has setup the JMeter proxy and tried, but did n't work. I have followed the below steps. Launch jmeter 2.3.3, added thred group to test plan Under Workbench-add-non-test elements- added HTTP proxy server. proxy server setting are port:9090, target:use recording controller, grouping:donot group samplers, Type:HTTp request and checked the boxes of all under http sampler settings Saved the settings Now in browser(IE 7.0 or firefox 3.0.16), under connection settings, setup the manual proxy settings as local host and port as 9090(no auto detect settings nothing, only manual proxy). Setting saved Now in the jmeter, started the http proxy server. Open a browser and hit the webpage needs to be tested. The page is not opened. In fact because of the changes made in browsers, no pages are opened. Whenever i try hitting a page, the pages are recorded in the Jmeter. but without the page open, how can i test. I looking for an immediate answer and my work is blocked. Immediate answer would be appreciated.

  Read the article

• BackupExec 2012 File System Archiving - Access is denied to Remote Agent

  - by AllisZero

  Gentlemen, I've been struggling with a Trial version of Symantec Backup Exec 2012 for about a week now. It was installed as an upgrade to our 12.5 license, and the setup completed with no issues. The reason I upgraded is solely for the File System Archiving option as I'm working to reduce the amount of live data in my servers. Backups work A-Ok and I have followed the instructions in the Admin Manual to make sure I had filled all requirements. The account BE is running under is a member of the Local administrators group as required and has been added to the test share that I'm using to evaluate the archiving function. Testing the credentials in the job setup window always works fine, and I am able to add both regular and Admin$ shares to my Archive selection. However, every time I run the Archive job, I get the following message: https://dl.dropbox.com/u/59540229/BEXec.png I've already tried to troubleshoot DNS resolution issues as suggested in the Symantec KB to no avail. The only thing I can think of, at this point, is that a trial license doesn't allow me to use the Archiving function, although that would seem silly on their part. Appreciate any assistance or information. Thanks.

  Read the article

• Apache Proxy and Rewrite, append directory to URL

  - by ionFish

  I have a backend server running on http://10.0.2.20/ from the local network, which serves similar to this: / (root) | |_user1/ | |_www/ | |_private/ | |_user2/ |_www/ |_private/ (etc.) Accessing http://10.0.2.20/user1/ of course, contains 'www' and 'private' folders and is proxied through a public server using Apache's Reverse Proxy. I'd like it so the following happens: http://public-proxy-server/user1/ actually shows the content from http://10.0.2.20/user1/www/ without indicating it in the URL. (/private/ would not be accessible via the public proxy server). The key here, is for it to be dynamic, so all requests to http://public-proxy-server/*/should show content from http://10.0.2.20/*/www/. Again, the proxy currently works fine; below is the config: (On the public server) <VirtualHost *:80> ServerName www.domain.com ProxyRequests Off ProxyPreserveHost On ProxyVia full ProxyPass / http://10.0.2.20/ ProxyPassReverse / http://10.0.2.20/ </VirtualHost> (On the backend server) <VirtualHost *:80> ... #this directory contains folders 'user1' and 'user2' DocumentRoot /var/www/ ... </VirtualHost>

  Read the article

• What are problems and pitfalls with a public facing Active Directory

  - by Ralph Shillington

  The situation that i'm faced with is this: We plan on using a number of server applications hosted on Amazon EC2 machines, mainly Microsoft Team Foundation Server. These services rely heavily on Active Directory. Since our servers are in the Amazon cloud it should go without saying (but I will) that all our users are remote. It seems that we can't setup VPN on our EC2 instance -- so the users will have to join the domain, directly over the internet then they'll be able to authenticate and once authenticated, use that token for accessing resources such as TFS. on the DC instance, I can shut down all ports, except those needed for joining/authenicating to the domain. I can also filter the IP on that machine to just those address that we are expecting our users to be at (it's a small group) On the web based application servers, I imagine all we need to open is port 80 (or 8080 in the case of TFS) One of the problems that I'm faced with is what domain name to use for this Active directory. Should I go with "ourDomainName.com" or "OurDomainName.local" If I choose the latter, does that not mean that I'll have to get all our users to change their DNS address to point to our server, so it can resolve the domain name (I guess I could also distribute a host file) Perhaps there is another alternative that I'm completely missing.

  Read the article

• Configure IIS site to work with host header & hosts file entry

  - by HarveySaayman

  I'm I bit of an IIS / Web noob (I'm a C# backend service / winforms dev) so please bare with me :-) I've set up a site in IIS on my local dev machine. In the bindings section of the site ive added 4 bindings, all 4 for http: Host Name Port IP Address blog.sourcecube.co.za 26581 * www.blog.sourcecube.co.za 26581 * blog.sourcecube.co.za 26581 127.0.0.1 www.blog.sourcecube.co.za 26581 127.0.0.1 in my hosts file (drivers\etc\hosts), i've added the folling entries: 127.0.0.1 blog.sourcecube.co.za 127.0.0.1 www.blog.sourcecube.co.za when i ping my domain name from the command line it does in fact resolve to the loopback address, 127.0.0.1. So what I'm expecting to happen when i navigate to blog.sourcecube.co.za in my browser is for it to resolve to 127.0.0.1, and when the request hits IIS, it should know which site to serve because of the host header? But when i navigate to blog.sourcecube.co.za, i get an "Unable to connect, Firefox can't establish a connection to the server at blog.sourcecube.co.za" error. What am I doing wrong? --- UPDATE --- Navigating to blog.sourcecube.co.za:26581 from my browser works... I'd like get it working without specifying the port number though.

  Read the article

• Malicious content on server - next steps advice [closed]

  - by Under435

  Possible Duplicate: My server's been hacked EMERGENCY I just got an e-mail from my hosting company that they got a report of malicious content being hosted on my vps. I was unaware of this and started looking into it. I discovered a file called /var/www/mysite.com/osc.htm. Soon after I discovered some weird php files wp-includes.php and ndlist.php both recognized as being PHP/WebShell.A.1 virus. I removed all these files but I'm unsure of what to do next. Can anyone help me analyze the output below of sudo netstat -A inet -p -e and give advice on what's best to do next. Thanks very much in advance Proto Recv-Q Send-Q Local Address Foreign Address State User Inode PID/Program name tcp 0 0 localhost.localdo:mysql localhost.localdo:37495 TIME_WAIT root 0 - tcp 0 1 mysite.com:50524 xnacreators.net:smtp SYN_SENT Debian-exim 69746 25848/exim4 tcp 0 0 mysite.com:www tha165.thehealtha:37065 TIME_WAIT root 0 - tcp 0 0 localhost.localdo:37494 localhost.localdo:mysql TIME_WAIT root 0 - udp 0 0 mysite.com:59447 merlin.ensma.fr:ntp ESTABLISHED ntpd 3769 2522/ntpd udp 0 0 mysite.com:36432 beast.syus.org:ntp ESTABLISHED ntpd 4357 2523/ntpd udp 0 0 mysite.com:48212 formularfetischiste:ntp ESTABLISHED ntpd 3768 2522/ntpd udp 0 0 mysite.com:46690 formularfetischiste:ntp ESTABLISHED ntpd 4354 2523/ntpd udp 0 0 mysite.com:35009 stratum-2-core-a.qu:ntp ESTABLISHED ntpd 4356 2523/ntpd udp 0 0 mysite.com:58702 stratum-2-core-a.qu:ntp ESTABLISHED ntpd 3770 2522/ntpd udp 0 0 mysite.com:49583 merlin.ensma.fr:ntp ESTABLISHED ntpd 4355 2523/ntpd udp 0 0 mysite.com:56290 beast.syus.org:ntp ESTABLISHED ntpd 3771 2522/ntpd

  Read the article

• problems installing mysql and phpmyadmin to localhost

  - by Joel

  Hi guys, I know there have been many similar questions, but as far as I can tell, most of the other people have gotten further than I have... I'm trying to get a WAMP setup happening. I've got PHP and Apache running and talking to each other. PHP is in c:\PHP Apache is in it's default program files folder. mySQL is in it's default install location. I have localhost setup at D:\public_html\ I'm able to navigate to localhost and see html and php files. But I have a simple mySQL test file: <?php // hostname or ip of server (for local testing, localhost should work) $dbServer='localhost'; // username and password to log onto db server $dbUser='root'; $dbPass=''; // name of database $dbName='test'; $link = mysql_connect("$dbServer", "$dbUser", "$dbPass") or die("Could not connect"); print "Connected successfully<br>"; mysql_select_db("$dbName") or die("Could not select database"); print "Database selected successfully<br>"; // close connection mysql_close($link); ?> When I try and open this, I get "could not connect" Now, I haven't even created a database yet, because I can't log into mySQL with phpmyadmin-so I think I've done something wrong in my mySQL install because they aren't talking to each other. I guess my main question is how do I first create a database in mySQL to be sure I have even installed it correctly?

  Read the article

• error: unexplained error (code 130) at rsync.c(541) [sender=3.0.7]

  - by brazorf

  This error: unexplained error (code 130) at rsync.c(541) [sender=3.0.7] error is happening after i changed router. Actually, i found out that this error just happens on a ctrl+c signal, so it could be not representative about the error itself. The command i run is very basic: rsync -avz --delete /local/path/ username@host:/path/to/remote/directory Basically, the rsync just stuck there and nothing's happening, until i ctrl+c. After interrupting the process i got the error in subject. I past the whole thing here: rsync -avvvvz --delete /source/path/ username@host:/path/to/direectory cmd=<NULL> machine=HOSTNAME user=username path=/path/to/direectory cmd[0]=ssh cmd[1]=-l cmd[2]=username cmd[3]=HOSTNAME cmd[4]=rsync cmd[5]=--server cmd[6]=-vvvvlogDtprze.iLsf cmd[7]=--delete cmd[8]=. cmd[9]=/path/to/direectory opening connection using: ssh -l username HOSTNAME rsync --server -vvvvlogDtprze.iLsf --delete . /path/to/direectory note: iconv_open("UTF-8", "UTF-8") succeeded. ^C[sender] _exit_cleanup(code=20, file=rsync.c, line=541): entered rsync error: unexplained error (code 130) at rsync.c(541) [sender=3.0.7] [sender] _exit_cleanup(code=20, file=rsync.c, line=541): about to call exit(130) The authentication runs on ssh via rsa key. I tried basic troubleshoot such as: ping the remote host ssh -l username remote.host check software firewall logs i asked the remote host sysadmin to check for logs, and when i run that command a ssh connection is actually being established and i can state there is no comunication/authentication/name resolution issue here. Rolling back to old router make this work again. Both client and server are running ubuntu 10.04. Try to take a look at my router configuration, where i'm no experienced at all, but i didnt see any "suspect" (what i was looking for is firewall blocking something) setting. The router itself is DLINK DVA-G3670B. Any suggestion? Thank You F.

  Read the article

• DVD Share on Vista Home Premium Failing

  - by hpunyon

  UPDATE: - I can't find any Local Policy Editor for Vista Home Premium, as suggested. - I did learn about registry keys: allocatecdroms, allocatefloppies, allocatedasd and tried adding these keys (individually and collectively) and setting them to both 0 or 1. There was no positive affect on read access to the DVD root folder - always Access Denied. ORIGINAL POST: Failing read access to the root folder of a DVD drive in Vista Home Premium laptop using the Guest account - Access Denied. The client is an XP Home PC that can see, but not access, the data in the share. I'm only trying to read the data DVD - not trying to write/burn anything. On the Vista laptop, I have: All Firewalls and Antivirus disabled.UAC disabled. Password checking disabled. "Advanced Shared" the DVD drive, with "Everyone" having full-access permissions to the share. Tried adding Guest and Anonymous users having full-access permissions to the share. RestrictAnonymous=0 set in the registry. Both PC's are in the same workgroup (MSHOME) The XP Home client sees the shared DVD in \Vista_Hostname\ but when I double click the drive icon on the client, I get a popup that access is denied, check with the administrator, etc. I can share other folders on the Vista PC and see and READ these from the XP Home client. If I enable password checking on the Vista side, I get a user/password popup, and I can authenticate (using my known Vista account, that happens to have Admin rights) and then I can get to see and read the DVD data. I need to open this up so that the (default) Guest user can see and access the DVD data files.

  Read the article

• How do I increase the buffer size for domain sockets in OS X 10.6

  - by Chas. Owens

  In Linux I have no problem dumping tons of data into a domain socket, but the same code on OS X 10.6.2 blows up after about 65 records. The socket reader code looks like #!/usr/bin/perl use strict; use warnings; use IO::Socket; unlink "foo"; my $sock = IO::Socket::UNIX->new ( Local => 'foo', Type => SOCK_DGRAM, Timeout => 600, ) or die "Could not create socket: $!\n"; while (<$sock>) { chomp; print "[$_]\n"; } And the client code looks like #!/usr/bin/perl use strict; use warnings; use IO::Socket; my $sock = IO::Socket::UNIX->new ( Peer => 'foo', Type => SOCK_DGRAM, Timeout => 600, ) or die "Could not create socket: $!\n"; for my $i (1 .. 1_000_000) { print $sock "$i\n" or die $!; } close $sock; The error message I get is No buffer space available at write.pl line 15.. It seems fairly obvious that there is a difference in the buffer size between Linux and OS X, but I don't know how to set it OS X (or what the possible negative side effects might be).

  Read the article

• port forwarding problem

  - by Claudiu

  I want to set up an svn server on my computer, so it's available from anywhere. I think I set up the repository correctly, using CollabSVN. If I go to Repo-Browser with TortoiseSVN and point it to svn://localhost:3690, it shows the proper repository. The problem now is that I'm behind a router. My local IP is 192.168.1.45 . Doing svn://192.168.1.45:3690 also works. My global IP is, say, x.x.x.x. Just doing svn://x.x.x.x:3690 doesn't work, which makes sense, since I have to set up port forwarding. I'm using a Verizon router. Using their web interface (on 192.168.1.1) I added the following port forwarding rule: IP Address forward to: 192.168.1.45 Source Ports: Any Dest Ports: 3690 Forward to: 3690 Protocol: TCP However, even after applying this rule, going to svn://x.x.x.x:3690 doesn't work. It takes a few seconds to fail, then says that the connection couldn't be established because the server connected to didn't respond properly after a period of time. What's interesting is that a random port, like svn://x.x.x.x:36904 fails immediately, saying that the target machine actively refused the connection. So I figure that the forwarding rule did something, but not fully what was necessary. Any ideas on how to get this working? The router model is MI424-WR and the firmware version is 4.0.16.1.56.0.10.12.3. UPDATE: I also tried setting destination port to 45000, and still forwarding to 3690, in case something was wrong w/ the lower-numbered ports, but to no avail. I also tried port 80 to port 3690, still all in vain.

  Read the article

• Why does my DD-WRT not accept SSH connections from my laptop?

  - by Vlad Seghete

  So, here is my system: I have a 2Wire AT&T modem/router which I use for wireless and a Buffalo router flashed with DD-WRT which is physically attached to the 2Wire and set in the DMZ. I set everything up on the DD-WRT to be able to connect to it using ssh and also so that it forwards ssh requests on a different port to one of the servers behind it. Now, when I am physically connected to the DD-WRT all this works great and as I would want it to. I ssh into the two different ports using the WAN IP of my network, and I get where I expect to land. If, however, I am connected using wi-fi to the 2Wire, the same commands do not work. I do not get an error, simply a timeout. I have trouble understanding this, since the DD-WRT is set in the DMZ and everything should pass to it. To further complicate the problem, I tried connecting to the same IP using my phone (wireless disabled, so really from the WAN) and surprise, it works! If I go back on the local network by enabling the wifi, the ssh connection times out. To make this even stranger, my WAN IP address always responds to pings (meaning in all the above situations). What could be going on here? I know what I should do, completely disable the 2wire as a router and use it strictly as a modem and them use all the routing capabilities of the dd-wrt. It's what I will probably end up doing anyway, but my question remains, because I really want to know what is happening here.

  Read the article

• Nagios check_host_alive and check_ping not showing host as down

  - by Kyle

  I am using the check_host_alive command to send 5 packets every minute to all my routers at remote locations. I noticed today I received a notification from The AT&T Global Client Support Center that a router was down (which can take 5-30 minutes to send these notices out) and never received a notice from Nagios. I went onto Nagios and it is was showing the host as alive with a latency of 0ms. This tells me it is seeing the automated response from my router in the data center that, "TTL expired in transit" as a reply from the remote router. Is there anyway for me to tell nagios to check where the reply is comming from? I feel like other people have to of had this issue... I tested it with the check_ping command and it produced the same results. I have the command defined has %hostname% and the proper IP in the host definition, and it works fine for telling me the latency is high. Any ideas are welcome, I have already exercised my Google skills with no results. EDIT: root@IM-UBTU:/# /usr/local/nagios/libexec/check_ping -H 192.168.250.1 -w 100.0,10% -c 200.0,20% -vvv CMD: /bin/ping -n -U -w 10 -c 5 192.168.250.1 Output: PING 192.168.250.1 (192.168.250.1) 56(84) bytes of data. Output: From 10.69.10.2 icmp_seq=1 Time to live exceeded It knows something is wrong why doesn't it give me a warning?

  Read the article

• Microsoft Licensing Scenario/Questions [closed]

  - by user17455

  Possible Duplicate: Can you help me with my software licensing question? I am a member of a team developing a third party application (APP) that listens for and services connections from remote devices via TCP. Also, some of these remote devices allow 1 or more users to interact with the remote device. On some of the remote devices, it is impossible for a user to interact with the device. The user/remote device makes no use of any Windows Server service - not DHCP, not IIS, not File Server, not Print Serer, not AD. The remote device's only connection to the Windows Server machine is through the APP's TCP ports. Our company has no interaction with Microsoft. We do not have a Microsoft sales team. Past inquiries have determined that it is cheaper for us to buy Microsoft software (and CALs) retail than to enter into any kind of "arrangement" with Microsoft. I have many questions about SQL Server CALs and Windows Server 2008 CALs. How can I obtain authoritative/legally binding answers? I am not looking for FREE legal advice. I AM looking for FREE advice about who/what/where I can responsibly spend my money to get meaningful information. I fear that passing this on to the local company law firm will just mean that I will be paying them to educate themselves on Microsoft licensing. And if that's like writing code to a new Microsoft API - they are not going to get it right the first time. Going to Microsoft for answers sounds like swimming up to a hungry shark and asking "One leg or two?" I am hoping someone has been down this road before and knows a law firm/lawyer that is experienced in these matters. Any help/suggestion welcome. Thanks.

  Read the article

• How do I change the Dropbox directory on a headless GNU/Linux server?

  - by DrTwox

  I have installed Dropbox 2.0.0 via command line on my home server (Ubuntu Server 12.04) to use for off-site automated backups, but I can't change the directory that the Dropbox daemon keeps synced. I've tried the following: The official docs say to use the desktop application, which is not applicable in my situation. However I installed the desktop app on my desktop machine and changed the default folder location, but I can't find where this change is stored in the ~/.dropbox/ directory so I can make the same change on the server. This page (and several others) recommends a Python script to do the job. Looking at the script, it opens a SQLite database called ~/.dropbox/dropbox.db, which does not exist on my Dropbox install, leading me to believe the script is out-of-date. This forum thread suggests manually inserting the required row in the config.db database, which I did, but it made no difference. I checked the same database file on my desktop machine, and it does not have the dropbox_path key, so I'm presuming the information in that thread is also out of date for version 2.0. I have tried to launch the Dropbox GUI configuration wizard over SSH with X11 forwarding, as suggested in one of the answers, but the binary must detect the absence of a local X11 install and it starts a command line daemon instead, which provides no means to change the option I need. I am currently using a symlink, as suggested as an answer, but this is a kludge. I would like to know the correct way to make the change. How do I change the Dropbox directory on a headless GNU/Linux server? Update: I've ditched Dropbox and started using Copy. Their Linux tools and support is far superior to Dropbox. I leave this question here in case someone, someday, can answer it.

  Read the article

• Free, simple, configurable SOCKS5 server

  - by Pooria Azimi

  I've been looking (for the past 6-7 hours) for a fast, free and configurable SOCKS5 server. I haven't found anything that matches my needs. They are either too complicated, too bare-bones or simply buggy as hell. This is (all) I need: I want it to run on Linux (and also OS X, preferably) I want it to listen on localhost:8888 When my app (say wget.. or curl --socks5=localhost:8888) requests http://www.google.com/search?q=asd (or any other url - both http and https), I want it to fetch the page not from google's servers, but from http://localhost:4444/cached?uri=http://www.google.com/search%3Fq%3Dasd. Nothing more! I don't need caching, or anything else. I just want a SOCKS5 server, running locally, which redirects all queries to my own (local) server. It could be written in C, C++, Python, PHP, Perl, Node.js or any other language. I don't care, as long as it supports my (very limited) needs, or I can easily change the source to make it so. Thanks a lot

  Read the article

• nginx reverse proxy to apache mod_wsgi doesn't work

  - by user11243

  I'm trying to run a django site with apache mod-wsgi with nginx as the front-end to reverse proxy into apache. In my Apache ports.conf file: NameVirtualHost 192.168.0.1:7000 Listen 192.168.0.1:7000 <VirtualHost 192.168.0.1:7000> DocumentRoot /var/apps/example/ ServerName example.com WSGIDaemonProcess example WSGIProcessGroup example Alias /m/ /var/apps/example/forum/skins/ Alias /upfiles/ /var/apps/example/forum/upfiles/ <Directory /var/apps/example/forum/skins> Order deny,allow Allow from all </Directory> WSGIScriptAlias / /var/apps/example/django.wsgi </VirtualHost> In my nginx config: server { listen 80; server_name example.com; location / { include /usr/local/nginx/conf/proxy.conf; proxy_pass http://192.168.0.1:7000; proxy_redirect default; root /var/apps/example/forum/skins/; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } After restarting both apache and nginx, nothing works, example.com simply hangs or serves index.html in my /var/www/ folder. I'd appreciate any advice to point me in the right direction. I've tried several tutorials online to no avail.

  Read the article

• How do I replicate Gmail filtering (forwarding mostly)?

  - by projectdp

  I have reached the limits of Gmail forwarding. Before there was no need to verify forwarding addresses. It's a problem for me now because the addresses I want to forward to are not natural inboxes but automated systems with no way to track the verification email contents. I want to set this up for example: mobile - email - facebook-email - flickr-email - tumblr-email - posterous-email How do I do this without Gmail filters? I think I need to use fetchmail to watch my inbox and then autoforward to the above addresses. Is fetchmail the best solution to this issue? Any other MRA's? I'd like to do some more complicated things with the emails in an automated fashion too, how would I go about monitoring the inbox, doing some actions to the email before forwarding, and forward everywhere? prerequisites: a server: fetchmail daemon to poll the account local mailbox script to clean & forward appropriately (python probably) sendmail + ~/.forward file backup email account (Gmail probably) Any help would be greatly appreciated. I'm trying to automate my social content distribution.

  Read the article

• OpenSWAN KLIPS not working

  - by bonzi

  I am trying to setup IPSec between 2 VM launched by OpenNebula. I'm using OpenSWAN for that. This is the ipsec.conf file config setup oe=off interfaces=%defaultroute protostack=klips conn host-to-host left=10.141.0.135 # Local IP address connaddrfamily=ipv4 leftrsasigkey=key right=10.141.0.132 # Remote IP address rightrsasigkey=key ike=aes128 # IKE algorithms (AES cipher) esp=aes128 # ESP algorithns (AES cipher) auto=add pfs=yes forceencaps=yes type=tunnel I'm able to establish the connection with netkey but klips doesnt work. ipsec barf shows #71: ERROR: asynchronous network error report on eth0 (sport=500) for message to 10.141.0.132 port 500, complainant 10.141.0.135: No route to host [errno 113, origin ICMP type 3 code 1 (not authenticated)] Tcpdump shows 22:50:20.592685 IP 10.141.0.132.isakmp > 10.141.0.135.isakmp: isakmp: phase 1 I ident 22:50:25.602182 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 22:50:26.602082 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 22:50:27.601985 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 ipsec eroute shows 0 10.141.0.135/32 -> 10.141.0.132/32 => %trap What could be the problem?

  Read the article

• Revover original email from Sendmail log

  - by Xavi Colomer

  I have a website the contact form has been failing silently for two weeks (Wordpress + Contact form 7). Apparently updating to Contact Form 7 made the assigned email to fail [email protected], I also tested with [email protected] and it also failed until I tried with gmail and it finally worked. Apparently @telefonica.net and @me.com domains are not working with this version of the plugin, but I have to investigate the cause. I found the logs of the lost emails, but I would like to know If I can recover the sender or the content of the original messages. May 24 23:41:11 localhost sendmail[27653]: s4P3fBc3027653: from=www-data, size=3250, class=0, nrcpts=1, msgid=<[email protected]_web.com>, relay=www-data@localhost May 24 23:41:11 localhost sm-mta[27655]: s4P3fBdA027655: from=<[email protected]>, size=3359, class=0, nrcpts=1, msgid=<[email protected]_web.com>, proto=ESMTP, daemon=MTA-v4, relay=localhost.localdomain [127.0.0.1] May 24 23:41:11 localhost sendmail[27653]: s4P3fBc3027653: [email protected], ctladdr=www-data (33/33), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=33250, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (s4P3fBdA027655 Message accepted for delivery) May 24 23:41:12 localhost sm-mta[27657]: s4P3fBdA027655: to=<[email protected]>, ctladdr=<[email protected]> (33/33), delay=00:00:01, xdelay=00:00:01, mailer=esmtp, pri=123359, relay=tnetmx.telefonica.net. [86.109.99.69], dsn=5.0.0, stat=Service unavailable May 24 23:41:12 localhost sm-mta[27657]: s4P3fBdA027655: s4P3fCdA027657: DSN: Service unavailable May 24 23:41:12 localhost sm-mta[27657]: s4P3fCdA027657: to=<[email protected]>, delay=00:00:00, xdelay=00:00:00, mailer=local, pri=30000, dsn=2.0.0, stat=Sent Thanks

  Read the article

• xauth, ssh and missing home directory

  - by flolo

  We have several servers, and normaly everything works fine, except now... we get a new aircondition installed. This takes 36 hours and for this time almost all servers got shutdown, only 2 remaining servers run for the most important tasks (i.e. accepting incoming email, delivering some important websites, login-server). Everybody was informed that when they need appropiate data from the homedirs they should fetch it before take down. Long story short: Someone realized that he have run a certain program on one of the servers. No Problem, he can remote login into our login server and run the programm there without home directory (binaries are local and necessary information can be copied to the /tmp). That works like a charm until... ... the user needs to run a GUI programm. I find no easy way to make it running, usually ssh -Y honk@loginserver is enough but now the homedirectory is missing and ssh is not able to copy the cookies into ~/.Xauthority (as the file server with the home directories is down). Paranoid as all systemadmins all X-Server just listen locally not on tcp ports, so no remote X connection possible SSH config is waterproof - i.e. no way to set environment variables. My Problem is, that the generated proxy MIT cookie from ssh get lost as the .Xauthority doesnt exist. If I could retrieve it somehow I could reenter it a .Xauthority in /tmp. The only other option (besides changing the config) which came to my mind is, makeing a tunnel (netcat, or better ssh) from the remote host to the loginserver and copy the cookie manually (not sure if it the tcp-unix domain socket stuff works as expected). Any good suggestions (for the future - now our servers are already up)?

  Read the article

• MacOS creates a new mount on AFP path calls

  - by jAndy

  Hi Folks, following scenario: In my webapp, my customers are using Firefox as target browser. They have the need to open afp:// folders via Javascript. To make a long story short, this really works. You need to setup Firefox with about:config and set the value network.protocol-handler.external.afp to true. What happens then, the operating system (OSX) takes care of that path and it correctly opens a Finder window. The problem: OSX does create a new mount every time. It cannot distinct between afp://host/path/111 and afp://host/path/222 for instance. Furthermore, even if the afp path is 100% identical a new mount is created. It looks like this is the default behavior from OSX regardless of Firefox. So, is there any chance I can tell OSX not to create a new mount for some sub directorys which should get access over afp:// ? update: It looks like, there are OSX applications which can change the default behavior for network protocols. So you can change "somewhere" which application OSX should call for a protocol. If that is true, wouldn't it be possible to create a script which just opens the local path without a afp:// prefix ? The question here is, where is that configuration (?) to tell OSX which application to use for specific protocol. Any help welcome!

  Read the article

• What is the main reason of adsl modem/routers dying ?

  - by ldigas

  The other day my home adsl modem/router (dwg 684t in this case) died. A guy from the telecom company came, brought another so no problem in day to day operation, but he also left this one. Now, I'm interested ... it didn't fall, it wasn't electrocuted ... but it just doesn't work. What could be the problem ? Can they be fixed ? Is it worth it (in which case I would have two which is always nice) ... What are the usual problems that occur with them ? In this case, I can connect to the router, I can see its settings, I just can't connect to the internet. With the new one everything works. Weird. Edit: Additional question: Can those things be fixed ? I mean, is it worth giving it to a local tinker for him to experiment on it ? I'm not looking for a definite opinion, just your personal advice ... (although in the end I think I'm gonna archive it in the "cylinder register")

  Read the article

• Help about pure-ftp

  - by hai

  I setup pure-ftp on freebsd behind firewall. On pure-ftp setuped passsi mode ftp(rangle port 50400-50600) and firewall open port from 50400-50600 (include mode IN and out). But i try use ftp client connect but not connect. Nofinication error status: Connecting to 210.245.89.95:21... Status: Connection established, waiting for welcome message... Response: 220---------- Welcome to Pure-FTPd [privsep] ---------- Response: 220-You are user number 1 of 50 allowed. Response: 220-Local time is now 13:20. Server port: 21. Response: 220-IPv6 connections are also welcome on this server. Response: 220 You will be disconnected after 15 minutes of inactivity. Command: USER bk Response: 331 User bk OK. Password required Command: PASS Response: 230 OK. Current directory is / Command: SYST Response: 215 UNIX Type: L8 Command: FEAT Response: 211-Extensions supported: Response: EPRT Response: IDLE Response: MDTM Response: SIZE Response: REST STREAM Response: MLST type;size*;sizd*;modify*;UNIX.mode*;UNIX.uid*;UNIX.gid*;unique*; Response: MLSD Response: ESTA Response: PASV Response: EPSV Response: SPSV Response: ESTP Response: 211 End. Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is your current location Command: TYPE I Response: 200 TYPE is now 8-bit binary Command: PASV Response: 227 Entering Passive Mode (210,245,88,98,138,1) Command: MLSD Error: Connection timed out Error: Failed to retrieve directory listing Status: Connecting to 210.245.88.98:21... Status: Connection established, waiting for welcome message... Help me.

  Read the article

< Previous Page | 644 645 646 647 648 649 650 651 652 653 654 655  | Next Page >