Search Results

Search found 2602 results on 105 pages for 'dell vostro'.

Page 65/105 | < Previous Page | 61 62 63 64 65 66 67 68 69 70 71 72  | Next Page >

• Uncontrolled Fan and Crash

  - by RobotbeatsHuman

  I don't have sensors to properly run lm-sensors. The computer will turn on but shortly there after all the fans in it will speed way up. It stays like this for a few minutes and then the computer shuts off. Tried resetting the BIO. Went to try installing a BIOs update but it wont stay on long enough for me to try that or to do a clean install. Could this be the motherboard dying? It's mainly the CPU fan that ends up going max. after a few minutes. I checked the PSU and It's a Dell Inspiron 580. If you need more system specs just le me know.

  Read the article

• Choppy/unresponsive keyboard and mouse pointer until suspend

  - by Stefan Thyberg

  I had a problem where my mouse and keyboard would be choppy. The mouse pointer would work at "1-2 fps" and the keyboard would keep missing letters as i was typing them. Since both are USB-Devices, i suspected a problem there immediately, so whenever i got this problem, i would suspend the computer and start it again, for the problem to be gone. The problem started appearing when I plugged the mouse and keyboard directly into the computer rather than the USB-Hub in the screen. I'm using a Logitech UltraX Flat and a Razer Lachesis, on a Dell Latitude E6510.

  Read the article

• Samba network sharing NTFS drives and root permissions from local drives

  - by Bill

  I'm able to share my internal 2ndry NTFS drives (sdb1,2 and 3) on the network with Windows computers now but even though Samba read/write is enabled, Windows network computers can only open files "read-only" and can't save files to the samba shared drives/folders. I try to set permissions in Ubuntu via folder and/or file properties even logged in root via Nautilus but all the samba shared folders and files are set as owner = root, accessible and does not allow me to change them to read/write, it just resets to root, accessible, in other words, I can't change permissions. I'm running Ubuntu 11.04 Gnome on an old Dell Dimension 2400. Also, in order to for me to copy or move any files from the Ubuntu drive to the sdb1,2 or 3 drives, I have to gksu nautilus. This consequently prevents me from copying .ISO files to my "Multisys" thumb drive too.

  Read the article

• Trying to boot from usb

  - by iron

  I have similar issues but none with the 12.04 build. Im trying this on a dell d610 laptop with a bad hard drive and was told i could just directly boot from the usb drive. Im using an 8g usb drive and i have tried using the uui tool and get this message. SYSLINUX 4.06 EDD 4.06-pre1 Copyright (c) 1994-2011 H.Peter Anvinet al ERROR: No configuration file found No DEFAULT or UI configuration directive found! Then i tried using unetbootin and got the bootup screen with only the default option and it would say auto boot with a 10 sec countdown and start over again. I do have the boot sequence for usb first.

  Read the article

• Logitech M515 does not work after upgrade to 12.04

  - by user877329

  After upgrading to 12.04, my Logitech M515 does not work here is some output from the terminal: lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0411:002a BUFFALO INC. (formerly MelCo., Inc.) Bus 001 Device 004: ID 055d:3021 Samsung Electro-Mechanics Co. Bus 002 Device 002: ID 413c:2005 Dell Computer Corp. RT7D50 Keyboard Bus 004 Device 002: ID 0582:0074 Roland Corp. EDIROL UA-25 Bus 005 Device 002: ID 046d:c52b Logitech, Inc. Unifying Receiver dmesg | grep Logitech [ 30.470528] logitech-djreceiver 0003:046D:C52B.0004: hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.3-2/input2 The cursor does not move. Also the mouse was working in 11.10 and is working in Windows NT 5.1.2600.

  Read the article

• Can't print, CUPS package corrupted and hangs on re-install

  - by Little Bobby Tables

  When I upgraded to Ubuntu 10.4 (Maverick), the upgrade process got stuck on the post-installation of the CUPS package. I had to kill processes and run several forced updates before I could finally get regular updated. Ever since I can't print - The printed file gets messed up and crashes the printer. I also can't re-install CUPS, as each time the installation hangs and I have to kill it before it completes. I tried to find a workaround for this problem, but in vain. Does anyone know how to bypass this? Or at least why can the post-installation hang, and how to re-install a problematic package? Some system specs and other hints: Dell D630 laptop running Ubuntu 10.4, Gnome desktop, standard LAN network, printing to an LPD server. Everything worked fine on 9.10. Also, the printed files themselves are not corrupted. The problem does not seem to be Evince-specific, but common to all printouts.

  Read the article

• GRUB- error: no such partition grub rescue and Error: No default or UI configuration directive found boot > on pendrive

  - by Ash

  I have dell inspiron, previously I installed Ubuntu 11.10 on my Windows 7 and made it dual boot. But since I want to upgrade my Ubuntu version and change the partition spacing, I deleted 11.10 partition directly and extended my hardrive space (Windows + Ubuntu) at that moment everything was fine. Then I prepared a 12.04 32bit USB and installed it . It was installed but isn't showing dual boot option like 11.10 and my machine directly boot into Windows 7. So instantly i again deleted my 12.04 partition . Now I login into Windows 7 but whenever I put USB ( with 12.04 ) to boot from it, I am facing error of "no such partition grub rescue" even though I try to put lower version(11.04) it showing another error "Error: No default or UI configuration directive found boot " I have reinstall Windows 7 and reformat all partition, still I am facing same error :(

  Read the article

• Wifi won't work without ethernet (Ubuntu 12.04)

  - by alok

  I have a strange problem. I am running Ubuntu 12.04 on a Dell Studio 1558 laptop. I'm usually unable to access Wifi (I have a BCM43224 wireless card with the STA proprietary driver installed.) So I have to unplug the ethernet cable from my Wifi router and stick it into my laptop's ethernet port to access the Internet. But when I stick the cable back into the Wifi router and try connecting to Wifi, Wifi inexplicably starts working. How can I get Wifi to work all the time without having to 'jumpstart' it with an ethernet connection?

  Read the article

• How do I rotate my monitor using xorg?

  - by user1106405

  I have just installed KUbuntu 12.10, and I am attempting to rotate my monitor 90 deg to the left. When I add the option to rotate, the monitor seems to ignore the directive. I'm currently using dual 02:00.0 VGA compatible controller: NVIDIA Corporation GF104 [GeForce GTX 460] (rev a1) 03:00.0 VGA compatible controller: NVIDIA Corporation GF104 [GeForce GTX 460] (rev a1) and NVidia driver version 310 My xorg.conf is as follows: # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 304.51 (buildd@komainu) Fri Oct 12 12:53:49 UTC 2012 # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 310.14 ([email protected]) Tue Oct 9 13:04:01 PDT 2012 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 1280 0 Screen 1 "Screen1" RightOf "Screen0" Screen 2 "Screen2" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "1" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Samsung SyncMaster" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 60.0 Option "DPMS" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Unknown" ModelName "DELL 1908WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 EndSection Section "Monitor" Identifier "Monitor2" VendorName "Unknown" ModelName "DELL 1907FP" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 76.0 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:2:0:0" Screen 0 EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:2:0:0" Screen 1 EndSection Section "Device" Identifier "Device2" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:3:0:0" EndSection Section "Screen" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: 1920x1200 +0+0; DFP-0: 1920x1200_60 +0+0; DFP-0: 1600x1200 +0+0; DFP-0: 1600x1200_60 +0+0; DFP-0: 1280x1024 +0+0; DFP-0: 1280x1024_60 +0+0; DFP-0: 1280x960 +0+0; DFP-0: 1280x960_60 +0+0; DFP-0: 1024x768 +0+0; DFP-0: 1024x768_60 +0+0; DFP-0: 800x600 +0+0; DFP-0: 800x600_60 +0+0; DFP-0: 800x600_56 +0+0; DFP-0: 640x480 +0+0; DFP-0: 640x480_60 +0+0; DFP-0: nvidia-auto-select @1920x1080 +0+0; DFP-0: nvidia-auto-select @1920x720 +0+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: 1920x1200 +0+0; DFP-0: 1920x1200_60 +0+0; DFP-0: 1600x1200 +0+0; DFP-0: 1600x1200_60 +0+0; DFP-0: 1280x1024 +0+0; DFP-0: 1280x1024_60 +0+0; DFP-0: 1280x960 +0+0; DFP-0: 1280x960_60 +0+0; DFP-0: 1024x768 +0+0; DFP-0: 1024x768_60 +0+0; DFP-0: 800x600 +0+0; DFP-0: 800x600_60 +0+0; DFP-0: 800x600_56 +0+0; DFP-0: 640x480 +0+0; DFP-0: 640x480_60 +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "DFP-2: nvidia-auto-select +0+0" Option "Rotate" "left" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Device2" Monitor "Monitor2" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Enable" EndSection Edit: If I delete the xorg.conf and reboot, I am able to rotate my monitor, however, my third monitor is not recognized: Screen 0: minimum 8 x 8, current 3360 x 1200, maximum 16384 x 16384 DVI-I-0 disconnected (normal left inverted right x axis y axis) DVI-I-1 disconnected (normal left inverted right x axis y axis) DVI-I-2 connected 1920x1200+0+0 (normal left inverted right x axis y axis) 518mm x 324mm 1920x1200 60.0*+ 1600x1200 60.0 1280x1024 60.0 1280x960 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 HDMI-0 disconnected (normal left inverted right x axis y axis) DVI-I-3 connected 1440x900+1920+0 (normal left inverted right x axis y axis) 408mm x 255mm 1440x900 59.9*+ 75.0 1280x1024 75.0 60.0 1280x800 59.8 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 640x480 75.0 72.8 59.9

  Read the article

• manage 2 wireless device

  - by yi.tang.uni

  I erased Windows 7 and installed Ubuntu 12.04 on my Dell Latitude E4200. I an very happy with my choice but with little pity. I cannot use the wireless service in my university as the build-in device works unstable. I bought a USB wireless device, which solve the problem. However, the build-in device keep to sent me message about unable to connect, which waste laptop's cup & battery. The phsical bottom to turn off wireless affect both devices. So the question is: "How can I manually shut down wireless device?" There is another interest comes to my mind: "Does 2 wireless improve the overall internet usage if I run a high-internet-consuming program like BT ?" Thank for your time and energy.

  Read the article

• Low graphics mode on ubuntu 12.10 with intel 4000

  - by Amey Jah

  I recently upgraded to 12.10 (fresh install). Now I am facing wierd problem, randomly for when I boot I get a message of low graphics. For now, I switch to console using alt+f1 and then rebboot. On reboot, I select recovery mode, allow system to boot and then again reboot. Now I select normal mode and my graphics loads smoothly. Could you please tell me what could e the issue? I have Dell inspiron 5230 with Intel 4000 onboard graphics. --Amey

  Read the article

• Can't activate "mirror display"

  - by Nemo Peeters

  I have Ubuntu 12.04 on a Dell latitude E6410, I have a problem when using the VGA output I always have dual monitor and can't switch on the "mirror display" toggle under systems setting/displays. It's rather annoying when having to do presentation with a video projector. the option "mirror display" is in light grey and I can"t tick the box. Thanks for those who might have an idea how to resolve this? update: driver is: Intel® Ironlake Mobile x86/MMX/SSE2 card something like this ? description: VGA compatible controller product: Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 02 width: 64 bits clock: 33MHz

  Read the article

• Unable to login following permission changes in device manager (11.10 + Gnome)

  - by Symanuk

  (Running Gnome 3 on Ubuntu 11.10) Everything working well (at least a couple of months), until recently when I changed the permissions through the device manager on the sda1 /2/ 3 drives, thinking it would save all the switching I seem to have to do between users in order to see / use files I previously copied across from an external drive. Now when I boot up the Ubuntu splash screen loads indefinitely, and if I go in through the GRUB / recover option, i'm getting a load of negative permission messages back (regardless of using the fsck or remount options) Either way = unusable machine (Laptop Dell Inspiron n5050), and no way through to login. I'm looking for: (1) a way back in so any help greatfully received (answers need to be pretty basic as i'm a novice), and (2) if i'm to learn anything, a decent thread on setting permissions within Ubuntu / Gnome 3. I'm new to both Ubuntu & Linux, so please be gentle!! Cheers

  Read the article

• Ubuntu appears very small at 1080p, text almost undreadable.

  - by Dakota

  Alright... So I have a 15" dell studio xps with a 1080p screen. Everything seems really small with 1080p, in 720 everything is fine but just looks very low res. So I definitely want to get the full resolution the display can give me but dont want everything so small. help?? EDIT: Well yes higher resolution means more pixels. But it shouldnt mean fonts the size of of 7 in MS word, and webpages looking like their at 50%... http://i.imgur.com/Ds76nk8.jpg http://i.imgur.com/9fW8vEt.jpg Im not saying windows is better, but windows did not appear miniature at 1080.

  Read the article

• GUI Application Resolution from Text Mode OS

  - by brettw

  I'm trying to turn a computer into a Linux thin client via Ubuntu. I have a Dell OptiPlex 755 loaded with Ubuntu 14.04 installed and fully patched. I've configured the OS to run in text mode and automatically launch the VMWare Horizon's client, which works. The issue is that when the Horizon client launches, its resolution is only 1/4 of the screen. I've played with the resolution settings in grub which appears to modify the text environment but not the application environment for Horizon's. Can someone point me in the right direction on how to increase the resolution for a GUI application launch from text mode so it's full screen. Thanks!

  Read the article

• How to install XAMPP?

  - by Rani.Shemer

  Hi all im a noob on Ubuntu/Linux World, So i need some that give a full tutorial to How to install Xampp from apachefriends.org correctly on Ubuntu 11.10 + all beyond Ubuntu for 32 bit and also 64 bit Desktop Version.. and also i need this: Make a Folder on Your Home Folder and Linked to htdocs from Apache Web Server Make a GUI interface for Xmapp Start Xampp when Ubuntu Boot Up or Start Ubuntu (Note: i ask it for both X86 and X64 so people in the further can see the tutorials) New Data: What i did was i download from apachefriends.org for now and i also what to say that I'm currently running Ubuntu 11.10 X64 bit for Dell Studio 1558 processor intel i3 i will let you know guys which solution was the best, and it is for a Desktop Version of Ubuntu 11.10 (Laptop 15 inch screen ^_^ ) not Server Ubuntu

  Read the article

• Continuous integration testing server: hosted, own desktop, or own server

  - by Victor

  For testing, I am planning to run a continuous integration testing. There are mainly two options: hosted, or own desktop/server. I will break it into 3 options I have: Hosted: Economical, $10-20/month for a small app Less setup, the CI company manage all hardware and software Desktop: I could just buy a simple, cheap desktop as a test server (about $500). Used server: My current office is offloading some old Dell rack server (Probably dual core Xeon, which I can purchase for $50 or less Please advise me which best serves me for a small team of 2-3 developers. Thanks.

  Read the article

• Chrome + Touchscreen + Unity (14.04)

  - by Luis Fernando P. Gonzalez

  I've got a Dell 14R with touchscreen with Ubuntu 14.04. When I start Google Chrome by clicking the launcher with the TouchPad or with the Super+ combination, touch support in Chrome doesn't work. When I touch some element, it only gets focus, but doesn't activate the element (button, field, etc). And touch gestures don't work. In the other hand, if I start Chrome by touching the launcher button, touch scroll works in Chrome, even flicking to left does back to the previous page, etc. It doesn't makes sense to me, but is always like this, even across reboots. Anyone can confirm this? Any idea on how to fix?

  Read the article

• Keyboard layout issues using Ubuntu 12.04 in ssh via X11 for mac

  - by LostInTranslation

  I just upgraded from 10.04 LTS to 12.04 LTS on my server (DELL Intel XEON). By SSH login from my mac (OS X Lion) everything is fine (no issues with command lines) but when I open a window through X11, the keyboard layout is now completely messed up. As an owner of a french mac keyboard, I got used to such issues and could deal by guessing the "QUERTY" keys, but this time it's worse. To fix it, I tried: 1/ sudo dpkg-reconfigure keyboard-configuration = no effect 2/ sudo gnome-control-center then change the keyboard settings, however adding a couple of keyboard layouts did not change anything. I feel there is something to do with the X11 forwarding. Any hints? Thanks

  Read the article

• HP Pavilion dv7 dual boot with ubuntu and original win7 issues

  - by Neasy11

  I just bought a hp dv7 and I want to dual boot it with the win7 it came with and ubuntu 12.04.1. I shrunk the C partition to make room for the ubuntu one then downloaded an burnt the iso. Next I booted from the cd and followed the simple instructions until I got to the page of the install to choose the partition where all choices were greyed out and the table was completely blank and the drop down only had one choice. After researching this I found that a main problem might be that I can only have 4 primary partitions and the computer was shipped with the 4 already (system,C,recovery,hp tools). I guess my question is what is the best way to go about completing this dual boot? I have read to delete the hp tools partition or combine it with another, I just want a step by step of how to dual boot this computer, I have done plenty of computers in the past but never ran into these issues that come with an HP (should have got a dell lol)!

  Read the article

• How to fix openGL error for Vmware Workstation 9?

  - by Xxx Xxx

  I have recently installed Vmware workstation 9 on Ubuntu 12.04 & i have migrated my VM's from windows to Ubuntu 12.04 . Now i am getting openGL error & it says no 3D acceleration as shown in pic below How Do I Fix It ? UPDATED Before i have windows 7 ( host os ) & it was working fine with 3D Acceleration & no OpenGL error . Now my i have Ubuntu 12.04 ( host os ) & openGL error The Laptop is DELL INSPIRON N5110

  Read the article

• Deleted entire harddisk. Now my laptop won't boot anything and stuck at grub rescue!

  - by Jahan

  My laptop is Dell Inspiron N4030. I used to use Ubuntu 12.04 and it was on the entire hard drive. I tried to install windows 7 but my laptop couldn't install it. So, I decided to delete the entire hard drive and do a fresh install of Windows 7. But after deletion I immediately removed the gparted live usb which I was using to delete the partitions of my hard drive. And then tried booting from windows 7 cd, didn't work, tried ubuntu live cd, didn't work, tried hiren's boot cd, didn't work, tried super grub disk, didn't work. Probably I'm not doing it right. Help needed badly.

  Read the article

• Inspiron 5720 unclaimed hardware

  - by Chelios

  I have two unclaimed devices in my Dell Inspiron 5720: *-display UNCLAIMED description: 3D controller product: NVIDIA Corporation vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress cap_list configuration: latency=0 resources: memory:f0000000-f0ffffff memory:c0000000-cfffffff memory:d0000000-d1ffffff ioport:3000(size=128) *-serial UNCLAIMED description: SMBus product: 7 Series/C210 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 04 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:f1614000-f16140ff ioport:efa0(size=32) What are these devices and what drivers do I need for them? Thanks!

  Read the article

• Not getting auto login page on my Hathway internet connection

  - by Vasu

  I am using firefox browser and my laptop is DELL Inspiron 1545. I am using Hathway internet connection. When i switch on my internet modem and try to use(browse any website), for the first time in a day it will redirect me to Hathway's login(something like "login.hatyway.com/.....") page automatically. It is working fine in windows but not in Ubuntu 11.10. So I go back to windows every time and then login and then i come back to ubuntu to use. Could you please let me know if there is a solution to this problem.

  Read the article

• internal error message pops up after each time system is rebooted

  - by Biju

  I had installed ubuntu 12.04 using wubi. But each time i boot the system an internal error message pops up. As show below:- Executable path /usr/share/apport/apport-gpu-error-intel.py Package xserver-xorg-video-intel 2:2.17.0-1ubuntu4 Problem Type crash Apportversion 2.0.1-0ubuntu7 and so on.. I had earlier upgraded to ubuntu 12.04 from ubuntu 11.10. And encountered the same issue. Hence i uninstalled the OS and reinstalled using wubi. I had posted the same query in ubuntu.com/support (Question Number: 195525) But couldnt find a solution. I am using dell inspiron with intel pentium. Need ur help in resolving this issue. thanking u, Biju

  Read the article

< Previous Page | 61 62 63 64 65 66 67 68 69 70 71 72  | Next Page >