Search Results

Search found 93816 results on 3753 pages for 'nexus one'.

Page 65/3753 | < Previous Page | 61 62 63 64 65 66 67 68 69 70 71 72  | Next Page >

• Devices on one switch can't see devices on another switch

  - by jockey69

  I have RoadRunner Internet cable service hooked to a Motorola Surfboard modem. This is connected to a 10/100 wireless router (located in the garage). Downstairs, I have a ZyXEL GS-108b gigabit switch connected to one port on the router. From this switch I ran connections to a PS3, DVR, Vonage box and a wireless router (Buffalo AirStation 10/100). The Buffalo AirStation works as a wireless AP for other laptops, iPads and cell phones. Upstairs, I have an Asus gigabit switch connected to a gaming desktop, printer, and a media server on FreeNAS (PS3 Media Server on FreeNAS). The router is configured to assign static IPs to both the PS3 and the media server. Problem - I connect a laptop to the switch downstairs after disabling the wireless, thus making sure that I am accessing internet through the wired connection (and the router in the garage). All my computers, iPads and cell phones are able to connect to the internet without a problem. My PS3 connects to the interent with a wired connection but is unable to access the media server (I get a message that no media server is found). I used a wired laptop downstairs (connected to switch downstairs) but am unable to ping either the PS3 or media server! I may be doing something silly but am at my wits' end. Please help!

  Read the article

• Adobe Acrobat Reader don't zoom out the page enough in "one page" mode

  - by mbaitoff

  I'm using Adobe Acrobat Reader version 9.4 under Debian Lenny. I'm experiencing a problem: when I push the "Show one page at a time" button, I expect the page to zoom such that pressing PgUp/PgDn would turn to the next/previous page. However, the zoom seems to be not enough - very thin bottom portion of the page doesn't fit inside the reader window, and pressing PgUp/PgDn gives the jitter of the same page, and I have to push twice to get to the next page. It is even worse in continuous page mode - a roll of pages begin to be non-synced with window boundaries, ending up with page break right in the middle of the view after several turns of the pages. This behaviour doesn't occur on windows version - I have a page properly zoomed in single/continuous modes, so that turning the pages is performed as page-at-once, as intended. How to make the Acrobat Reader fit the page to window properly? Thats how it looks before pressing PgDn (notice the bottom edge of the "paper" hidden beneath the bottom window edge): Thats how it looks after pressing PgDn (notice the "paper" bottom edge emerged from beneath the window edge, while the "paper" upper edge hides behind the upper window edge, showing that the document window size is not enough to contain the whole page):

  Read the article

• nginx 2 symfony2 web application, one ip no domain

  - by Krzysztof Koch

  I have irritating with nginx. I set up in /usr/share/nginx/www/firstapp one application and in /usr/share/nginx/www/secondapp. in my default conf i setup that in / root localization i want first app: when write 9.9.9.9 in browser show me first app, and when i write 9.9.9.9/makeup, there not show me seccond app. Why first app displays me good, and seccondapp cannot? Please help me. Sorry for quality here pasterbin code: enter link description here server { listen 80; server_name localhost; root /usr/share/nginx/www/firstapp/web; access_log /var/log/nginx/$host.access.log; error_log /var/log/nginx/error.log error; # strip app.php/ prefix if it is present rewrite ^/app\.php/?(.*)$ /$1 permanent; location / { root /usr/share/nginx/www/firstapp/web/; index app.php; try_files $uri @rewriteapp; } location /makeup/ { alias /usr/share/nginx/www/seccondapp/web/; index app.php; try_files $uri @rewriteapp; } location @rewriteapp { rewrite ^(.*)$ /app.php/$1 last; } # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 location ~ ^/(app|app_dev)\.php(/|$) { #fastcgi_pass 127.0.0.1:9000; fastcgi_pass unix:/var/lib/php5-fpm/www.sock; fastcgi_split_path_info ^(.+\.php)(/.*)$; include fastcgi_params; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param HTTPS off; #fastcgi_param SERVER_PORT 80; }

  Read the article

• Delete ARP cache on Mac OS when moving from one Wifi network to the other

  - by Puneet

  I am facing wireless connectivity problems when I move from one Wifi network to the other. Here is how it happens: I am at my friends place. I connect to his Wifi. His Wifi router ip address is 192.168.0.1. Everything is fine I close my laptop, come back to my house, open my laptop and I connect to the Wifi Network at my place. Different ESSID, but the Wifi router address is the same 192.168.0.1. At this point I cant get to anything on the internet. To debug I try to see if I can ping the router (192.168.0.1), I cant. I get a no route to host. Meanwhile airport tells me Im connected to Wifi. I see the arp cache and I see a permanent entry for 192.168.0.1 ? (192.168.0.1) at 5c:d9:98:65:73:6c on en1 permanent [ethernet] This permanent bit looks problematic. I go ahead and delete the arp cache entry and all is fine with the world until I go back to my friends place where the same situation plays out. Now my question is, why the hell is this happening? If there is no way around it, can I run a script on Wifi connect/disconnect to clear out the arp cache? Im using Mac OS X $uname -a Darwin 10.8.0 Darwin Kernel Version 10.8.0: Tue Jun 7 16:33:36 PDT 2011; root:xnu-1504.15.3~1/RELEASE_I386 i386

  Read the article

• One USB flash drive to rule them all

  - by Chris

  Yesterday I purchased a 32GB USB flash drive. I have a myrid of systems in my home, and would like to have one flash drive with setup files for all the various systems throughout the house. I kept the Fat 32 filesystem on the drive, as I figured that is probably the most universal. I then made the partition bootable using fdisk. I then copied the Windows 7 setup files to the drive. I then installed grub 2 (1.98) onto the drive using backtrack 5. I was then able to load the windows 7 setup / install from the flash drive on an older BIOS type motherboard. Now I would like to know how to get this to work on my MacBook Pro 8,2 with still retaining support for legacy computers. Is this possible, or is this just a pipe dream. I plan on getting OS X on the drive, gparted, and OS X86 on the drive when all is said and done. I've done various google searches but really haven't found a guide on how to setup a swiss army usb flash drive.

  Read the article

• Networking 2 Virtual PC with one VPC as DHCP server

  - by vivek

  My host OS is Win XP Professional. The host has a real network connection via DSL and I created a second network connection using Microsoft Loopback Adapter. Internet connection sharing is enabled. The Microsoft Loopback adapter has a IP address of 192.168.0.1. I have 1 Virtual PC which has Windows Server 2003. I have setup the network connection on this VPC to use Microsoft Loopback Adapter. I setup this VPC to be the Domain Controller , DNS Server and DHCP Server. I set this to a static IP address 192.168.0.2 (on the same subnet as the MS Loopback adapter) I have a second Virtual PC which also has Windows Server 2003. The network connection on this VPC is set to "Local Only". I want this VPC to get its IP address from the 1st VPC on which I setup as a DHCP server. What i want is the 2 VPC should be in a network with one of the VPC acting as the domain controller, DNS Server and DHCP server. The second VPC shoud get its IP address from the 1st VPC. It should be a part of the domain of the 1st VPC. When i tried to make the second VPC get the IP address from the first VPC I am not succeeding. Can somebody post some suggestions on how to go about this ?

  Read the article

• One Apache VirtualHost entry overrides another?

  - by johnlai2004

  I can't tell why one apache virtual host entry keeps overriding another. The following file // filename: cbl <VirtualHost 74.207.237.23:80> ServerAdmin [email protected] ServerName completebeautylist.com ServerAlias www.completebeautylist.com DocumentRoot /srv/www/cbl/production/public_html/ ErrorLog /srv/www/cbl/production/logs/error.log CustomLog /srv/www/cbl/production/logs/access.log combined </VirtualHost> keeps overriding this file // filename: theccco.org <VirtualHost 74.207.237.23:80> SuexecUserGroup "#1010" "#1010" ServerName theccco.org ServerAlias www.theccco.org ServerAlias webmail.theccco.org ServerAlias admin.theccco.org DocumentRoot /home/theccco/public_html ErrorLog /var/log/virtualmin/theccco.org_error_log CustomLog /var/log/virtualmin/theccco.org_access_log combined ScriptAlias /cgi-bin/ /home/theccco/cgi-bin/ DirectoryIndex index.html index.htm index.php index.php4 index.php5 <Directory /home/theccco/public_html> Options -Indexes +IncludesNOEXEC +FollowSymLinks allow from all AllowOverride All </Directory> <Directory /home/theccco/cgi-bin> allow from all </Directory> RewriteEngine on RewriteCond %{HTTP_HOST} =webmail.theccco.org RewriteRule ^(.*) https://theccco.org:20000/ [R] RewriteCond %{HTTP_HOST} =admin.theccco.org RewriteRule ^(.*) https://theccco.org:10000/ [R] Alias /dav /home/theccco/public_html <Location /dav> DAV On AuthType Basic AuthName theccco.org AuthUserFile /home/theccco/etc/dav.digest.passwd Require valid-user ForceType text/plain Satisfy All RewriteEngine off </Location> </VirtualHost> I tried a2ensite, a2dissite, and reloading I get this message * Reloading web server config apache2 apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName [Thu Apr 15 10:47:36 2010] [warn] NameVirtualHost 74.207.237.23:443 has no VirtualHosts Aside from that, I don't know what else could be wrong. Can anyone tell me what to do?

  Read the article

• Copy one db diagram from one db to another on different servers? (Same db)

  - by sah302

  I used the copy database wizard to copy my database from our test server to our production server, the database copied everything fine except for the diagram. Okay no problem, first I make sure the target database on production has the support objects created to use database diagraming. Then I select to import data from the other database and chose the dbo.sysdiagrams.Go through with the rest of the import data wizard, but then I get the following error: Validating (Error) Messages Error 0xc0202049: Data Flow Task: Failure inserting into the read-only column "diagram_id". (SQL Server Import and Export Wizard) Error 0xc0202045: Data Flow Task: Column metadata validation failed. (SQL Server Import and Export Wizard) Error 0xc004706b: Data Flow Task: "component "Destination - sysdiagrams" (31)" failed validation and returned validation status "VS_ISBROKEN". (SQL Server Import and Export Wizard) Error 0xc004700c: Data Flow Task: One or more component failed validation. (SQL Server Import and Export Wizard) Error 0xc0024107: Data Flow Task: There were errors during task validation. (SQL Server Import and Export Wizard) So apparently it didn't like that. What's the problem? I am pretty beginner in SQL Server and only do stuff via the GUI usually so am not sure what to do at this point. The databases are the same, but on different servers. Thanks!

  Read the article

• Forward mDns from one subnet to another?

  - by user37278

  Is there an ipfw rule that can easily forward mDns packets from one subnet to another? I have a Snow Leopard Server machine serving as the gateway between the two subnets and would like for machines in each subnet to see the services available in the other subnet. The gateway machine is already confirmed as configured correctly such that packets route correctly between the two subnets (ping works, traceroute shows the subnet hop, etc). My problem in designing a ipfw rule is that I don't know how to instruct that I would like multicast packets addressed to 224.0.0.251:5353 on en0 to be addressed to the same ip/port but on fw0 (the other interface). I attempted a rule such as fwd 192.168.10.1 log udp from 192.168.1.0/24 to 224.0.0.251 recv en1 to force the packet to hop over to the other interface (from en1 to fw0), but no dice. The ipfw log shows that the rule is being triggered by packets, but tcpdump isn't showing any packets on the other interface. Also, the only other firewall rules in place are the divert port 8668 and rule #65535 "allow any to any". Any suggestions? Thanks.

  Read the article

• FFmpeg overlay two videos, one input with transparency

  - by Gian B.

  I am trying to create a karaoke from a CD+G file (converted to AVI using FFmpeg) and add a video as a background of the lyrics. Here's a screenshot of a the output from CD+G conversion, for simplicity let's call this lyrics.avi http://imgur.com/wUwHUhV Now a have this video.mp4 file that I'd like to put behind this lyrics.avi Here's a sample of what I'm trying to achieve http://imgur.com/8GuWXtQ I'm sure most of you are familiar with karaoke. I haven't used FFmpeg much and I'm not really sure if what I want to achieve is possible with FFmpeg. Is it possible to overlay two videos, and add a transparency to one of the videos? In this case the colour black? How can I set the offset time of the lyrics.avi? Here's the command the I've tried so far: ffmpeg -i video.mp4 -i lyrics.avi -filter_complex "nullsrc=size=854x480 [base]; [0:v] setpts=PTS-STARTPTS, scale=854x480 [upperleft]; [1:v] setpts=PTS-STARTPTS, scale=854x200 [bottomleft]; [base][upperleft] overlay=shortest=1 [tmp1]; [tmp1][bottomleft] overlay=shortest=1:y=280" -c:v libx264 -y karaoke.mp4

  Read the article

• SSL connection error for only one site (of many) on server

  - by Matt Lacey

  I have a server running many websites, each with SSL. One of the sites is now refusing connections over SSL. This was previously working and I'm looking for assistance in determining what has been changed. Here's the situation: http://site1.com/ - works https://site1.com/ - works http://site2.com/ - works https://site2.com/ - Doesn't work (but did previously) Both sites are on the same server (Win Server 2003 SP2 - IIS6) Both sites use certificates from the same authority and are both valid (according to IIS). As far as I can tell, both sites have certificates configured identically in IIS. (Checked by a manual/visual check of properties, side by side) Through use of OpenSSL I can see that there's a "ssl handshake failure" when trying to connect to site2 using https. What could be the cause of this? How can I investigate further? Without SSL connections being available to this site, users are unable to log in or register. :( disclaimer: I'm not a server admin and not responsible for the box. Yes, there are wider issues here but I need to get this working again first.

  Read the article

• Firefox proxy authentication with Kerberos: one service ticket per connection (Linux)

  - by Dari

  I am trying to enable proxy authentication via Kerberos for Firefox. The setup is: Active Directory domain (for LDAP and Kerberos; this works and I can log in the computer and get Kerberos tickets without problems) Microsoft Windows witness machine (on which Firefox runs fine with no ticket problem) CentOS 6.3 system with Firefox (the tests were performed with both the 10.0.1 ESR found in the CentOS package repositories and the 15.0.1 downloaded from Mozilla's website) BlueCoat proxy with Kerberos authentication enabled For the moment, Firefox requests an element of a website, gets an HTTP error code of "407 Proxy Authentication Required" from the proxy, gets a ticket granting service (TGS) from the domain for the proxy and performs the request again while passing the ticket. The transaction runs fine. However, when more elements are requested (in parallel), Firefox requests one more ticket per proxy connection. And this takes many DNS queries, Kerberos interactions with domain controllers and costs a lot of time (for example, the home page of Adobe takes several minutes to load and at the end, I have about 30 valid Kerberos tickets). I am stuck on this since a while, and help would be greatly appreciated. Minor information: the CentOS operating system is virtualized with VMware Player 3.1.3, but I do not think this would be a game changer.

  Read the article

• Transferring domain from one registrar to another

  - by Macha

  I have a domain from my old web host, which was free with my hosting account. After a few years, I am moving to a VPS. Most of my other domains were registered with Namecheap, so it was just a matter of changing a few DNS records. However, given that my old host does not provide me with a DNS control panel, and I don't want to be paying a full hosting bill for just domains, I'm now looking into transferring it. My old host says there will be a charge of $15 to them. NameCheap's page seems to imply you don't need the current registrar to do anything, but it also seems to be based on sending an email to the one listed in whois. Of course, my old host have whoisguard on the domain so the only email on it is [email protected] (and not a unique [email protected], just [email protected]) which doesn't go to me. Again, there doesn't seem to be an option to disable this. So, is it a case of paying my old host's fee, and paying again for the domain from NameCheap, or is there some other way to transfer my domain? (I'm not really sure which of the trilogy sites this is best for.)

  Read the article

• Slackware - Assigning routes (IP address ranges) to one of many network adapters

  - by Dogbert

  I am using a Slackware 13.37 virtual machine within VirtualBox (current). I currently have a number of Ubuntu VMs on a single server, along with this Slackware VM. All VMs have been set up to use "Internal Network" mode, so they are all on a private LAN, and can see each other (ie: share files amongst themselves), but they remain private from the outside world. On on the these VMs (the Slackware one), I need to be able to grant it access to both this private network, and the internet at large. The first suggestion I found for handling this is to add another virtual network adapter to the VM, then set it to NAT. This results in the Slackware VM having the following network adapter setup: -NIC#1: Internal Network -NIC#2: NAT I want to set up the first network adapter (NIC#1) to handle all traffic on the following subnets: 10.10.0.0/255.255.0.0 192.168.1.0/255.255.255.0 And I want the second virtual network adapter (NIC#2) to handle everything else (ie: internet access). May I please have some assistance in setting this up on my Slackware VM? Additionally, I have searched for similar questions on SuperUser and Stackoverflow, but they all seem to pertain to my situation (ie: they all refer to OSX, or Ubuntu via the use of some UI-based tool). I'm trying to do this on Slack specifically via the command-line. Thanks!

  Read the article

• Site Goes Offline Every Day At Midnight - No One Knows Why

  - by HollerTrain

  0 down vote favorite Seems today a website I manage has been going online and offline between 12a and 12:25a. I have no idea what is causing the issue so I am seeking guidance on where to start. It is a Wordpress based site. So here is what I DO know: I have a pingdom account which alerts me when the site goes offline so we can see every day, like clockwork, the site goes on/off. At the time of the ups/downs I see a lot of strain on the memory usage. Look at the load average when the site is going online/offline (http://screencast.com/t/BRlfXkqrbJII). Then I ran this command to restart http (http://screencast.com/t/usVtYWZ2Qi) and the memory usage then goes down to this (http://screencast.com/t/VdTIy3bgZiQB). An hour after I restarted http, the site then went offline/online so restarting the http didn't do much help. When the site is going offline/online, I ran the top command and get this (http://screencast.com/t/zEwr7YQj3). Here is a top command when the site is at it's lowest (http://screencast.com/t/eaMfha9lbT - so this would be dubbged "normal"). Here is a bandwidth report (http://screencast.com/t/AS0h2CH1Gypq). The traffic doesn't seem to be that much (http://screencast.com/t/s7hrWNNic1K), but looking at my times the site is going up/down this may be one of the reasons? I have the dvp Nitro package at Media Temple (http://mediatemple.net/webhosting/nitro/). So at this point I would request some help in trying to figure out what the cause of this is, and how I can go about pinpointing this issue. ANY HELP is greatly appreciated.

  Read the article

• "one-off" use of http_proxy in a Chef remote_file resource

  - by user169200

  I have a use case where most of my remote_file resources and yum resources download files directly from an internal server. However, there is a need to download one or two files with remote_file that is outside our firewall and which must go through a HTTP proxy. If I set the http_proxy setting in /etc/chef/client.rb, it adversely affects the recipe's ability to download yum and other files from internal resources. Is there a way to have a remote_file resource download a remote URL through a proxy without setting the http_proxy value in /etc/chef/client.rb? In my sample code, below, I'm downloading a redmine bundle from rubyforge.org, which requires my servers to go through a corporate proxy. I came up with a ruby_block before and after the remote_file resource that sets the http_proxy and "unsets" it. I'm looking for a cleaner way to do this. ruby_block "setenv-http_proxy" do block do Chef::Config.http_proxy = node['redmine']['http_proxy'] ENV['http_proxy'] = node['redmine']['http_proxy'] ENV['HTTP_PROXY'] = node['redmine']['http_proxy'] end action node['redmine']['rubyforge_use_proxy'] ? :create : :nothing notifies :create_if_missing, "remote_file[redmine-bundle.zip]", :immediately end remote_file "redmine-bundle.zip" do path "#{Dir.tmpdir}/redmine-#{attrs['version']}-bundle.zip" source attrs['download_url'] mode "0644" action :create_if_missing notifies :decompress, "zipp[redmine-bundle.zip]", :immediately notifies :create, "ruby_block[unsetenv-http_proxy]", :immediately end ruby_block "unsetenv-http_proxy" do block do Chef::Config.http_proxy = nil ENV['http_proxy'] = nil ENV['HTTP_PROXY'] = nil end action node['redmine']['rubyforge_use_proxy'] ? :create : :nothing end

  Read the article

• Multiple rack apps on nginx + passenger, one as root, the other not...config help

  - by cannikin

  So I've got two apps I want to run on a server. One app I would like to be the "default" app--that is, all URLs should be sent this app by default, except for a certain path, lets call it /foo: http://mydomain.com/ -> app1 http://mydomain.com/apples -> app1 http://mydomain.com/foo -> app2 My two rack apps are installed like so: /var /www /apps /app1 app.rb config.ru /public /app2 app.rb config.ru /public app1 -> apps/app1/public app2 -> apps/app2/public (app1 and app2 are symlinks to their respective apps' public directories). This is the Passenger setup for sub URIs described here: http://www.modrails.com/documentation/Users%20guide%20Nginx.html#deploying_rack_to_sub_uri With the following config I've got /foo going to app2: server { listen 80; server_name mydomain.com; root /var/www; passenger_enabled on; passenger_base_uri /app1; passenger_base_uri /app2; location /foo { rewrite ^.*$ /app2 last; } } Now, how do I get app1 to pick up everything else? I've tried the following (placed after the location /foo directive), but I get a 500 with an infinite internal redirect in error.log: location / { rewrite ^(.*)$ /app1$1 last; } I hoped that the last directive would prevent that infinite redirect, but I guess not. /foo gets the same error. Any ideas? Thanks!

  Read the article

• EPP Protocol create multiple domains in one command

  - by yannis hristofakis

  I've seen <domain:check> command can check multiple domains in one command. Is it possible to do the same for the <domain:create>? <?xml version="1.0" encoding="UTF-8" standalone="no"?> <epp xmlns="urn:ietf:params:xml:ns:epp-1.0"> <command> <create> <domain:create xmlns:domain="urn:ietf:params:xml:ns:domain-1.0"> <domain:name>example.com</domain:name> <domain:period unit="y">2</domain:period> <domain:ns> <domain:hostObj>ns1.example.com</domain:hostObj> <domain:hostObj>ns1.example.net</domain:hostObj> </domain:ns> <domain:registrant>jd1234</domain:registrant> <domain:contact type="admin">sh8013</domain:contact> <domain:contact type="tech">sh8013</domain:contact> <domain:authInfo> <domain:pw>2fooBAR</domain:pw> </domain:authInfo> </domain:create> </create> <clTRID>ABC-12345</clTRID> </command> </epp>

  Read the article

• Check for unique rows, but ignore one particular column

  - by user269148

  I have an XML document, that looks like this: Column A to S with headers, and there are 1922 rows. This is an backup of some SMS, and I want to get rid of duplicates. The problem is, that the Time in the readable_date header has been messed up. There is nothing wrong with the date, but the clock time is wrong, so I have split that column in three, with Year, day and clock. I know I can use a standard filter, but it only looks for unique rows in a single column. What I want to perform, is to make a row check similar to this: F(x)=Check if Column 2A to (infinate) is equal to Column 3A to (infinate), but ignore column(R). IF True, then delete Column 3A to (infinate) Otherwise Check IF column 2A to (infinate) is equal Column 4A to (infinate) and so on. I need to ignore a particular column in a row every time, and need to do this for a complete sheet. And the formula check should apply for every row, when the first one is done checking for duplicates... If anyone else has a better solution, please say so. Anyway, anyone who can help?

  Read the article

• Why Would one VLAN have no Communication on one Switch?

  - by Webs

  So the problem is we have a device or host that needs to communicate on a specific VLAN. This VLAN is not new, it is running all throughout our environment and works fine. But the VLAN was recently configured on the switch in question, a Cisco 3750. The DHCP server is handing out addresses on that VLAN with no problem. I have verified the cable between the host and switch and tried multiple hosts, but none of them can communicate or get an address. I plugged my laptop into an empty port which had a different VLAN assigned and immediately got a DHCP address. When I changed that port to the same VLAN I'm having issues with I got the same problem. The laptop just sits there and tries to DHCP an address but nothing happens. I double checked the cores and their Layer 3 VLAN config and its fine too. Plus I figured the issue couldn't be with them because the VLAN works fine everywhere else it exists. So the only other thing I can think of is the switch, but the VLAN exists on the switch and seems to be configured correctly. The trunks appear to be configured just fine as well too. Anyone have any ideas? I'm lost on this one.

  Read the article

• Multiple Settings for One Monitor

  - by Lynda

  I have my monitor set to the way I like it, it shows colors accurately and not overly bright (white doesn't blind me). However I edit photos for the web and this is great for my screen but I have noticed when looking at other screens my photos will at times looked washed out and not a good presentation. If I manually change my monitor settings to be brighter (and a few other tweaks) I can replicate the look of other monitors close enough to help prevent washed out/blown out photos. Here is the issue, I need to be able to change settings between the two fairly easily. To manually set my monitor for one then back to the other can be time consuming and a pain to set right every time. I would like to be able to preset certain settings (in software) that I can quickly switch between by pressing hotkeys or clicking shortcut on my desktop. I have an AMD video card and have attempted to use the AMD VISION Engine Control Center to add presets then tweak the settings for each. However when I switch between the presets the settings are the same. How do I build presets using the VISION Engine Control Center that actually works (maybe I misunderstand what it is saving?) or is there a way to do this in Windows 7 or free software that actually works decently for this purpose?

  Read the article

• Fortigate restrict traffic through one external IP

  - by Tom O'Connor

  I've got a fortigate 400A at a client's site. They've got a /26 from British Telecom, and we're using 4 of those IPs as a NAT Pool. Is there a way to say that traffic from 172.18.4.40-45 can only ever come out of (and hence go back into) x.x.x.140 as the external IP? We're having some problems with SIP which looks like it's coming out of one, and trying to go back into another. I tried enabling asymmetric routing, didn't work. I tried setting a VIP, but even when I did that, it didn't appear to do anything. Any ideas? I can probably post some firewall snippets if need be.. Tell me what you want to see. SIP ALG config system settings set sip-helper disable set sip-nat-trace disable set sip-tcp-port 5061 set sip-udp-port 5061 set multicast-forward enable end Interesting Sidenote VoIP phones, with no special configuration can register fine to proxy.sipgate.co.uk, which has an IP address of 217.10.79.16. Which is cool. Two phones are using a different provider, whose proxy IP address is 178.255.x.x. These phones can register for outbound, but inbound INVITEs never make it to the phone. Is it possible that the Fortigate is having trouble with 178.255.x.x as it's got a 255 in it? Or am I just imagining things?

  Read the article

• Exchange emails not delivering for one user

  - by Cylindric

  We have an Exchange infrastructure going through a migration from 2003 SP2 (call it ExOld) to 2010 (ExNew). All users are now on the new server, but mail is still being directed to ExOld until testing is complete. ExNew sends emails directly to the internet. For one particular user, emails don't seem to be being reliably delivered, but the odd thing is that it's not all emails. I can see external emails in his inbox. If I send an internal email it works fine. If I send an email from Gmail to him it doesn't get through. If I telnet from outside to ExOld I can send an email to him. If I telnet from outside to ExNew I can send an email to him. This is a transcript that results in a successful send: 220 ExOldName Microsoft ESMTP MAIL Service, Version: 6.0.3790.4675 ready at Mon, 22 Oct 2012 10:55:26 +0100 EHLO test.com 500 5.3.3 Unrecognized command EHLO test.com 250-ExOldFQDN Hello [MyTestExternalIp] 250-TURN 250-SIZE 250-ETRN 250-PIPELINING 250-DSN 250-ENHANCEDSTATUSCODES 250-8bitmime 250-BINARYMIME 250-CHUNKING 250-VRFY 250-X-EXPS GSSAPI NTLM LOGIN 250-X-EXPS=LOGIN 250-AUTH GSSAPI NTLM LOGIN 250-AUTH=LOGIN 250-X-LINK2STATE 250-XEXCH50 250 OK MAIL FROM:[email protected] 250 2.1.0 [email protected] OK RCPT TO:[email protected] notify=success,failure 250 2.1.5 [email protected] DATA 354 Start mail input; end with . Subject:Test 1056 Test 10:56 . 250 2.6.0 Queued mail for delivery quit 221 2.0.0 ExOldFQDN Service closing transmission channel Emails go through Symantec Cloud, but their "Track and Trace" shows the messages going through, with a "delivered ok" log entry. 2012-10-22 09:19:56 Connection from: 209.85.212.171 (mail-wi0-f171.google.com) 2012-10-22 09:19:56 Sending server HELO string:mail-wi0-f171.google.com 2012-10-22 09:19:56 Message id:CAE5-_4hzGpY2kXFbzxu7gzEUSj5BAvi+BB5q1Gjb6UUOXOWT3g@mail.gmail.com 2012-10-22 09:19:56 Message reference: 135089759500000177171130001194006 2012-10-22 09:19:56 Sender: [email protected] 2012-10-22 09:19:56 Recipient: [email protected] 2012-10-22 09:20:26 SMTP Status: OK 2012-10-22 09:19:56 Delivery attempt #1 (final) 2012-10-22 09:19:56 Recipient server: ExOldIP (ExOldIP) 2012-10-22 09:19:56 Response: 250 2.6.0 Queued mail for delivery I'm not sure where to look on the old (or new) server for information as to where the mails are ending up.

  Read the article

• Transferring domain from one registrar to another

  - by Macha

  I have a domain from my old web host, which was free with my hosting account. After a few years, I am moving to a VPS. Most of my other domains were registered with Namecheap, so it was just a matter of changing a few DNS records. However, given that my old host does not provide me with a DNS control panel, and I don't want to be paying a full hosting bill for just domains, I'm now looking into transferring it. My old host says there will be a charge of $15 to them. NameCheap's page seems to imply you don't need the current registrar to do anything, but it also seems to be based on sending an email to the one listed in whois. Of course, my old host have whoisguard on the domain so the only email on it is [email protected] (and not a unique [email protected], just [email protected]) which doesn't go to me. Again, there doesn't seem to be an option to disable this. So, is it a case of paying my old host's fee, and paying again for the domain from NameCheap, or is there some other way to transfer my domain? (I'm not really sure which of the trilogy sites this is best for.)

  Read the article

• One workstation gets slow access to the server, but others are fast

  - by Mike Hanson

  I've just setup a machine with Windows Server 2008. It hosts various services, like IIS, POP3, SMTP, Music for Squeezeboxes, VNC. All was working well for the first week or so. One day I needed to create a mapped drive on the server, so it could access files on my workstation. Windows indicated that Network Discovery was needed, so I turned it on with the "Home / Office" option (rather than "Public"). This may be coincidence, but since that time I've been having troubles accessing various services from my main workstation (running Windows 7/64): POP3 continued working correctly, but SMTP was delayed or failed entirely. (Telnet took 20 seconds to connect, but Outlook would never send messages.) VNC failed entirely. I reinstalled it on the server, and now it works but feels sluggish. The music web server was extremely delayed and usually failed. I tried reinstalling, and now it takes about 30 seconds to show the page name on the browser tab, and another 30 seconds to display any page contents. Other machines on the local network seem fine, as do machines connected via the Internet. I don't believe I changed anything on my own machine that would cause this. I considered the possibility that my anti-virus was involved, so I uninstalled AVG (commercial version), but that didn't help. I installed Norton 360 after that, and it didn't complain of viruses on my machine, and the delays remained. Because only my machine is affect, I'm tempted to blame it, except that reinstalling software on the server improved the situation, so there is almost certainly something going on with the server too. The firewall has all the necessary ports open, and it works fine for the other workstations (including external machines connected via the Internet), which indicates that it should be OK. Any ideas?

  Read the article

< Previous Page | 61 62 63 64 65 66 67 68 69 70 71 72  | Next Page >