Search Results

Search found 21356 results on 855 pages for 'check digit'.

Page 656/855 | < Previous Page | 652 653 654 655 656 657 658 659 660 661 662 663  | Next Page >

• Oracle Linux screen freezes during installation

  - by Fearless

  I was installing Oracle Linux 6.4 on a server, and the screen suddenly froze. Here were the previous steps: I put in the disk, clicked install, checked the disk (no errors), did pre-install setup (clock, root password, host+domain name, etc.), configured two 40GB hard drives in a RAID1 array (no swap, 3100mb encrypted raid partitions, ~100mb ext4 partition mounting to /boot, encrypted ext4 RAID device with mounting to /), selected packages, hit continue. The system did its short preinstall processes, then when to the main installation screen with the long status bar. The installer proceeded like always, but around package 250 out of ~1000, the screen suddenly went black with a text cursor in the upper left corner of the screen and the mouse cursor in its previous place. Neither cursor moved and the only thing that triggered a response was a ctrl-alt-delete that rebooted it. I have run this in VMs before without this issue. Memtest hasn't reported anything, and the media check went smoothly. The machine has supported Ubuntu server without issues before. Any ideas? I have tried booting after that, but the grub bootloader tries to find fd0 for some reason (I have no idea why it would search for the floppy disk). UPDATE My server successfully installed, but won't boot up. I think that, for some reason, it is still using the old bootloader from the previous installation. Any ideas on how to fix that?

  Read the article

• Laptop CPU fan not working properly

  - by Smith

  My laptop's CPU fan is suddenly acting very bizarre, and I am at a loss for what to do so I am asking for some help. Specifically, the fan is not even starting to spin until the CPU reaches 60 degrees Celsius (checked through HWmonitor). Once it is on, however, it properly stays on even when the CPU gets back to idle temps around 38 Celsius. Before, the fan was simply starting with the computer and staying on like normal. I've checked this for consistency both by allowing cold boots to ramp up temperature to 60 Celsius (the slow climb also causing the laptop to become unreasonably warm near the heatsink), and also running Prime95 immediately to kickstart the fan (this works every time). The fan seems to be stationary when turning the computer on from either sleep or shutdown. The fan will start at POST very briefly, and then stop completely. I've checked the BIOS for a SmartFan setting but haven't found any. I've opened the case to check for dust or debris and have not found anything (I applied some canned air to the area just in case). The laptop is a Lenovo ThinkPad Edge E430 and the CPU is an Intel Core i5 3210m @ 2.5 GHz. Any advice would really be appreciated.

  Read the article

• JBoss database connection pool configuration

  - by Qben

  I am facing an connection pool issue in my clustered JBoss installation. From time to time one of my connection pools will hit the roof and I get a lot of these in my logfile. java.sql.SQLException: No ManagedConnections available within configured blocking timeout ( 30000 [ms] ); The odd thing is that I can see in the JMX console that the ConnectionCount hit the roof, but at the same time InUseConnectionCount is often quite small. The problem will resolve itself after a couple of minutes but during recovery phase my application will not work (for obvious reasons). The question is if this indicate an error in the configured timeouts of the connections (I pretty much use defaults), or if my pool is simply too small to handle the peaks. Under normal operation I would say I use ~40% of the configured max number of connections. The reason I just don't increase the max number of connection is that if I actually used up all connections I suspect that InUseConnectionCount would hit the roof. Hence I suspect I might have more issues than just a too small pool size. Maybe InUseConnectionCount has decreased at the time I check jmx-console and it actually do hit the roof? I tend to collect data every second minute. Any hints are more than welcome.

  Read the article

• Windows 7 Laptop Randomly Sleeping

  - by Josh Arenberg

  I'm running Windows 7 64-bit on a Lenovo laptop, and I have a problem wherein after I've put it to 'sleep' once, it will seemingly without any reason or warning go back to sleep every 10 to 15 minutes after that. Each time it wakes back up just fine, and you can happily continue on. However, 10 or 15 minutes later, it just drops out into sleep mode. I don't see any errors in the system logs. I don't think it's related to heat ( since it's not rebooting ). When I check the system event log, I can see where the machine goes to sleep, but it simply says "reason: application API", and doesn't indicate which app ( brilliant ). I don't see any errors from hardware or anything relating to sleep in the application log that would point to what is going on either. How can I find out which app is triggering this? EDIT: I confirmed that temperature wasn't the issue. I think it's important to keep in mind that this condition only happens after the first sleep. If I reboot, the problem goes away until I put it to sleep, after which it sleeps on it's own every few minutes. Is there no way to capture which app is calling the sleep routine?

  Read the article

• Undo Google Sync in chrome

  - by iamcreasy

  I didn't know that my google account wasn't in sync with my chrome for the last couple of months and now that I have link again, the restored record is several months old. Now, that I've lost all my recent bookmarks and all other stuff...is there anything or anyway so I could revert the Google sync so I can get my bookmarks back? Update 1 I have found that under C:\Users\Profile_Name\AppData\Local\Google\Chrome\User Data\Default there is a file named Bookmarks.bak that holds the old state of my bookmarks before the sync. Update 2 Bookmarks is the file that holds the current(after sync) bookmark list. I replaced Bookmarks with Bookmarks.bak and restarted chrome, but still chrome isn't fetching information from the updated file. So, I have my old bookmark information, but how to restore it in chrome. Update 3 : solved I still couldn't figure out why replacing the bookmarks file didn't work and aparently that's the only solution available on web. I reinstalled everything and then copied the old bookmarks file. Then I got my bookmarks back again. Lession learned : Check regularly if google sync is working.

  Read the article

• How to improve network performance between two Win 2008 KMV guest having virtio driver already?

  - by taazaa

  I have two physical servers with Ubuntu 10.04 server on them. They are connected with a 1Gbps card over a gigabit switch. Each of these host servers has one Win 2008 guest VM. Both VMs are well provisioned (4 cores, 12GB RAM), RAW disks. My asp.net/sql server applications are running much slower compared to very similar physical setups. Both machines are setup to use virtio for disk and network. I used iperf to check network performance and I get: Physical host 1 ----- Physical Host 2: 957 Mbits/sec Physical host 1 ----- Win 08 Guest 1: 557 Mbits/sec Win 08 Guest 1 ----- Phy host 1: 182 Mbits/sec Win 08 Guest 1 ----- Win 08 Guest 2: 111 Mbits /sec My app is running on Win08 Guest 1 and Guest 2 (web and db). There is a huge drop in network throughput (almost 90%) between the two guest. Further the throughput does not seem to be symmetric between host and guest as well. The CPU utilization on the guests and hosts is less than 2% right now (we are just testing right now). Apart from this, there have been random slow downs in the network to as low as 1 Mbits/sec making the whole application unusable. Any help to trouble shoot this would be appreciated.

  Read the article

• Varnish going sick

  - by junke1990

  I'm having trouble with Varnish, it works for a couple of views and then just goes sick... The weird thing is that it does work for about 20 or 30 requests. If I call apache directly it works fine. I'm running Varnish Version: 3.0.3-1 on Debian Squeeze and, for now, Apache on port 80 and Varnish on port 8080 on the same server.. I'm using https://github.com/mattiasgeniar/varnish-3.0-configuration-templates as base for my VCLs and modified the VCLs to support Concrete5. Anyone any clue on how I should debug this? backend default { .host = "127.0.0.1"; .port = "80"; .connect_timeout = 1.5s; .first_byte_timeout = 45s; .between_bytes_timeout = 30s; .probe = { .url = "/"; .timeout = 1s; .interval = 10s; .window = 10; .threshold = 8; } } LOG 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1353791312 1.0 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1353791315 1.0 0 Backend_health - default Still sick 4--X-R- 0 8 10 0.000689 0.000000 HTTP/1.1 301 Moved Permanently (the 301 is because I check for www.)

  Read the article

• What other ways can I load balance EC2 servers without using Elastic Load Balancing?

  - by undefined

  I have a web application that consists of a web server managed by a web hosting firm, a set of EC2 instances in amazons cloud and a MySQL database (hosted on the webserver). MySQL is behind a firewall and is set to allow access from Localhost and from a single IP address which is an Amazon Elastic IP address that is attached to the EC2 instance I have been running up to now. The problem is that I want to look at my scaling up and load balancing strategy for my EC2 instance. To this end I have been investigating the Elastic Load Balancers and Autoscaling tools that Amazon provides and have managed to set this up fine but for one thing - connecting to the MySQL database running on my webserver. I realised (thanks to answers on Serverfault) that I needed to check firewall settings and add the IP address for the load balancer, however Elastic Load Balancers provide you with a DNS name, not an IP address and infact the IP addresses change over time so this will not work. I have been told by the company hosting the database that the way the firewall works is to look up the IP address of the DNS name and store the IP rather than the DNS name. so basically this will not work and the only way to allow access would be to open up the SQL port to allow access from anyone! Is this a viable idea? Should I look at moving my database into the cloud? Is there another firewall that the server company can use? Should I find another way of load balancing (if so what?) tricky one eh? any help appreciated!

  Read the article

• Symlink path can be followed manually, but `cd` returns Permission denied

  - by Ricket

  I am trying to access the directory /usr/software/test/agnostic. There are several symlinks involved in this path. As you can see by the below transcript, I am unable to cd directly to the path, but I can check each step of the way and cd to the symlinked directories until I reach the destination. Why is this? (and how do I fix it?) Ubuntu 12.10, bash > ls /usr/software/test/agnostic ls: cannot access /usr/software/test/agnostic: Permission denied > cd /usr/software/test > cd agnostic bash: cd: agnostic: Permission denied > pwd -P /x/eng/localtest/arch/x86_64-redhat-rhel5 > ls -al | grep agnostic lrwxrwxrwx 1 root root 15 Oct 23 2007 agnostic -> noarch/agnostic > ls -al | grep noarch ... lrwxrwxrwx 1 root root 23 Oct 23 2007 noarch -> /x/eng/localtest/noarch > cd noarch > cd agnostic bash: cd: agnostic: Permission denied > ls -al | grep agnostic lrwxrwxrwx 1 5808 dip 4 Oct 5 2010 agnostic -> main > cd main > ls (correct output of `ls`) > pwd /usr/software/test/noarch/main > pwd -P /x/eng/localtest/noarch/main

  Read the article

• zfs pool error, how to determine which drive failed in the past

  - by Kendrick

  I had been copying data from my pool so that I could rebuild it with a different version so that I could go away from solaris 11 and to one that is portable between freebsd/openindia etc. it was copying at 20mb a sec the other day which is about all my desktop drive can handle writing from the network. suddently lastnight it went down to 1.4mb i ran zpool status today and got this. pool: store state: ONLINE status: One or more devices has experienced an unrecoverable error. An attempt was made to correct the error. Applications are unaffected. action: Determine if the device needs to be replaced, and clear the errors using 'zpool clear' or replace the device with 'zpool replace'. see: http://www.sun.com/msg/ZFS-8000-9P scan: none requested config: NAME STATE READ WRITE CKSUM store ONLINE 0 0 0 raidz1-0 ONLINE 0 0 0 c8t3d0p0 ONLINE 0 0 2 c8t4d0p0 ONLINE 0 0 10 c8t2d0p0 ONLINE 0 0 0 it is currently a 3 x1tb drive array. what tools would best be used to determine what the error was and which drive is failing. per the admin doc The second section of the configuration output displays error statistics. These errors are divided into three categories: READ – I/O errors occurred while issuing a read request. WRITE – I/O errors occurred while issuing a write request. CKSUM – Checksum errors. The device returned corrupted data as the result of a read request. it was saying low counts could be any thing from a power flux to a disk event but gave no suggestions as to what tools to check and determine with.

  Read the article

• Unable to install drivers of any kind of device on windows 8.1

  - by saadj55

  Windows 8.1 is unable to install drivers. First, I wanted to install Android ADB drivers for my Chinese Android Phone. I downloaded the relevant drivers from the manufacturers site and enabled USB debugging on my phone and tried to install it but Windows failed to find any drivers in the driver folder. After searching on google, I got to know that I will have to edit the win_usb.inf file in order to install the drivers so I did the editing part also. Added these line: %SingleAdbInterface% = USB_Install, USB\VID_0BB4&PID_0C03 %CompositeAdbInterface% = USB_Install, USB\VID_0BB4&PID_0C03 to both NTamd and NTx86 sections but the problem persists. Phone's current hardware id is: VID_0BB4&PID_0C03 I noticed that I need hardware ID with &MI_01 appended at the end. But Windows detects the device with the above hardware ID. I have the webcam drivers so I uninstalled WebCam Drivers to check if they can be installed back but I am also not able to install drivers for it. Windows is detecting the camera without that &MI_01 part. Please help. I cannot install webcam nor my android phone.

  Read the article

• How to access Virtual machine using powershell script

  - by Sheetal

  I want to access the virtual machine using powershell script. For that I used below script, Enter-PSSession -computername sheetal-VDD -credential compose04.com\abc.xyz1 where, sheetal-VDD is hostname of virtual machine compose04.com is the domain name of virtual machine and abc.xyz1 is the username of virtual machine After entering above command , it asks for password. When the password is entered I get below error, Enter-PSSession : Connecting to remote server failed with the following error message : WinRM cannot process the reques t. The following error occured while using Kerberos authentication: There are currently no logon servers available to s ervice the logon request. Possible causes are: -The user name or password specified are invalid. -Kerberos is used when no authentication method and no user name are specified. -Kerberos accepts domain user names, but not local user names. -The Service Principal Name (SPN) for the remote computer name and port does not exist. -The client and remote computers are in different domains and there is no trust between the two domains. After checking for the above issues, try the following: -Check the Event Viewer for events related to authentication. -Change the authentication method; add the destination computer to the WinRM TrustedHosts configuration setting or us e HTTPS transport. Note that computers in the TrustedHosts list might not be authenticated. -For more information about WinRM configuration, run the following command: winrm help config. For more information, see the about_Remote_Troubleshooting Help topic. At line:1 char:16 + Enter-PSSession <<<< -computername sheetal-VDD -credential compose04.com\Sheetal.Varpe + CategoryInfo : InvalidArgument: (sheetal-VDD:String) [Enter-PSSession], PSRemotingTransportException + FullyQualifiedErrorId : CreateRemoteRunspaceFailed Can someone help me out in this?

  Read the article

• Calculating memory footprints using /proc/sysvipc/shm

  - by MarkTeehan

  This is for a SLES 10 database server. One of my servers runs three databases and three app servers; I am analyzing how their shared memory segments grow and shrink to avoid intermittent out-of-memory scenarios. "Top" is hot helpful for this since its calculations for RES and VIRT are inconsistent. I am doing this by matching up the contents of /proc/sysvipc/shm with memory usage reported by the database admin console. I do this by totaling up saving the contents of /proc/sysvipc/shm and then total up "bytes" for all of the segments for the offending userid. This is a large server with hundreds of segments and tens (or hundreds) of GB of allocated memory per userid. However it doesn't match up - the database management software claims to be using around 25% more memory than the total I calculate. Negligible swap space is in use, so I am ignoring that. I am running it as root so I am sure I see all shared memory segments. My question is : is all (significant) allocated memory recorded in /proc/sysvipc/shm, or is this only shared memory (*and not "un-shared" memory?). If this is incorrect, what is the correct way to calculate out the total allocated memory for each userid? Also: I believe doing a 'cat' on this file locks server IPC. I check it every 5 seconds - is it likely that this frequency could be problematic? Thanks! Mark Teehan Singapore

  Read the article

• System Issues and Major Malfuctions after Failed hibernation Exit

  - by Sarah Seguin

  I have a HP G71-340US that went into hibernation mode for a while and when I tried coming out of it, I got an error message: You're computer cannot come out if hibernation . Status: 0xc000009a Info: A fatal error occurred processing the restoration data. File: \hiberfil.sys Any information that was not saved before the computer went into hybernation will be lost enter=continue So I hit continue and it ran soooo super slow it. It was seriously crawling. Finally I gave up and turned it off manually (IE press and hold the button). It's been a week or two since then and EVERY SINGLE TIME I have tried to to do ANYTHING it takes forever. When I say forever, I literally mean takes 5-7 minutes to load the internet, then the page itself, then to click a link, so on so forth. Eventually everything just goes not responding and I have to give up (4-6 HOURS later). I also cannot access my thumb/jump drives once I've managed to load windows. I was going to try runing malware bytes incase of a virus, but it's windows explorer developes errors and goes not responding on me. Currently I'm running scan disk or check disk and like every file is coming back unreadable. I let it run the last 2 hours straight in chkdesk and I'm only at 6 percent with around 500+ errors and still going. Yes, I've taken logs of the errors via cell phone camera and patience. A week or two prior to this happening I had to change our the hard drive due to blunt force trama next to the mouse. OH! Running on Windows 7: ) And I've tried loading the computer in safe mode and it makes absolutely no difference. Any and all help would be appreciated. I really don't know what to do from here and I'm kind of freaking out. I've googled different part of the error and things that I've done/seen and there are so many different answers/topics that I thought it best to just post the questions.

  Read the article

• error while resolving DNS requires

  - by user2803887

  I followed this document to configure master-slave powerdns servers... http://linuxmanage.com/master-slave-powerdns-managed-by-poweradmin.html Installation completed perfectly no errors even I feel DNS is trying to resolve some queries and parameter.. but while going through intodns.com i get below error for domain names which i have created in powerdns name server installed as above guide. Error Mismatched NS records WARNING: One or more of your nameservers did not return any of your NS records. Error Multiple Nameservers ERROR: Looks like you have less than 2 nameservers. According to RFC2182 section 5 you must have at least 3 nameservers, and no more than 7. Having 2 nameservers is also ok by me. Error Missing nameservers You should already know that your NS records at your reported by your nameservers are missing, so here it is again: nameservers ns1.makeittiny.com. ns2.makeittiny.com. I am much new to powerdns so not able to figure out where problem.. i check all things but not able to make out where problem remains.

  Read the article

• Why can I not edit, delete directories inside of this directory

  - by user43053

  Hello there, First, I thought this was PHP related, but maybe it isn't. My original post, which may be irrelevant now is located at the bottom. The problem is I have a directory : /articles/. In it are 10 sub directories. I have been changing the permissions lately, but now it seems all the permissions of the parent folder, sub-folders and files are either chmod 755 or 777. I cannot move, delete or edit files inside of this parent directory or sub-directories with my FTP-client. I can however edit, delete, create new files and directories and change them with PHP-functions without problems. What may the problem be? OLD POST. Ignore everything below this line: If I create a directory with mkdir(), or create a file with fopen(), file_put_contents() or SimpleXMLElement::asXML(), I am unable to access the file with my FTP-client or c-Panel File Manager. If I try to delete or edit them, I get errors. Dreamweaver suggests it is a permission problem or a network or filesystem fault (but I've set the permissions with chmod() to 0777, and when I check the cPanel, it confirms chmod 777. I also tried to use fileowner() and the function returns int(99), the same owner as those files that I could access with my FTP-client. It seems files and directories created with PHP can only be modified or be deleted with PHP. I thought this must be a server setup related issue, so I write it here. I am on a shared server, and I have no idea about setting up servers. EDIT: It seems the problem is different. I cannot move files with FTP-client to the parent, or sub-directories either. This problem may not be PHP related, then. It seems the problem applies to any directory, regardless of whether it was created by PHP. EDIT 2: The parent directory has chmod 755. Thank you for your time. Kind regards Marius

  Read the article

• How to fix Windows 7 when System Recovery Options hangs?

  - by seansand

  The battery power ran out on my HP G60 laptop and it shut down. Even after recharging, Windows 7 will now not start up. After any attempted startup, it bluescreens and takes me to the "Startup Repair (recommended)" / "Start Windows Normally" console screen. "Startup Repair (recommended)" appears to be the right choice, but when I choose it, I get taken to a screen which appears to be System Recovery Options (it's the same wallpaper as the screenshots here: http://www.sevenforums.com/tutorials/668-system-recovery-options.html). However, I just get a cursor with nothing else; no "System Recovery Options" window ever pops up. (A black console screen does pop up for a split-second but too fast to be able to read the text.) The empty screen with cursor hangs indefinitely. System Recovery Options normally runs off of a partition on the laptop hard drive. When I got the laptop, I also created a System Repair Disc (in fact I have more than one) and when I try use any of them; they all result in the same wallpaper and empty screen with lone cursor. Ctrl-Alt-Del does nothing. The computer did not come with a Windows 7 installation disc, so there's no obvious way to reinstall Windows 7. Safe mode does not work; startup fails and I just get sent back to the "Startup Repair (recommended)"/"Start Windows Normally" console screen. "Start in last good state" does not work either, same result as above. Running a memory & hard disk check found no errors. Do I have any options at all? "System Recovery Options" seems to be what I want, but the screen that is supposed to take me to them just hangs.

  Read the article

• Low 'Burst Rate' from SATA drive in HDTune?

  - by UpTheCreek

  I recently upgraded my laptop's v slow hard drive to a seagate momentus 7200. Everything is working fine, but I'm a bit confused by these benchmark results: The burst rate is significantly less than the Maximim transfer rate, and not much higher than the normal minimum (if you ignore the spikes). What's going on here? On the HDtune website it defines Burst Rate as: ...the highest speed (in megabytes per second) at which data can be transferred from the drive interface (IDE or SCSI for example) to the operating system. Which begs some questions... e.g. if this is the highest, then how did the bechmarking tool record the 103MB/sec maximum? And if this really is the true maximum, then where is the bottleneck? The laptops SATA interface is on an Intel 82801GBM southbridge controller. When I check in hardware manager, I see that it's driver is iaStor.sys from 2005. Maybe that's the issue? I'll look for a newever version, but any insights would be appreciated. Thanks UPDATE: Acorting to this page on the HDTune website... An important parameter of the test is the Burst Rate. This value should always be higher than the maximum transfer rate. A lower value is usually an indication of a configuration problem. So what might be the configuration problem?

  Read the article

• Gentoo server time issue, can't manually set time, NTPD won't correct, too big of a time difference

  - by kevingreen

  So, my server is living in the future, unfortunately I can't get lottery numbers, or stock picks out of it. It thinks this is the time: Thu Nov 7 04:07:18 EST 2013 Not correct, I tried to set the time manually via date in a few ways # date -s "06 NOV 2013 14:48:00" # date 110614482013 -- same output, same problem Which outputs Wed Nov 6 14:48:00 EST 2013, but when I check the date again, it's still set to Nov 7th 0400 or whatever. I checked my system messages, and I see this pop up often: Nov 7 03:54:00 www ntpd[4482]: time correction of -47927 seconds exceeds sanity limit (1000); set clock manually to the correct UTC time. Which makes sense, we're way off the correct time. But I can't seem to manually fix it. So now what? Also, I'm wondering if my hardware clock is setup correct, hwclock doesn't return any values. Would that be causing issues? This is a virtualized server, I don't have direct access to the hypervisor, but I can talk to who does, assume I can explain myself well enough. Thanks

  Read the article

• Static DHCP binding

  - by Alex

  Good time of day, SF people. I have created a manual DHCP binding entry on a Cisco router so that a client would always get leased to it. The clients wants to get the same address on both of his dual-boot linux systems. He tries to get an IP address leased and he succeeds on one of the dual-boot operating systems. When he reboots to another one he gets a lease for a completely different one. I don't get it. The MAC addresses are the same (we checked in ifconfig, so what could be happening here? Why is the router confused? Or is it something else? Also, how can I check DHCP server IP address who I have got an IP address from (on Linux)? Configuration on Cisco: ip dhcp pool MANUAL_BINDING0001 host 192.168.0.64 255.255.255.0 hardware-address dead.beef.1337 dns-server 192.168.8.11 default-router 192.168.0.254 domain-name verynicedomainigothere.cn PS. Is it mandatory to use client-name configuration line?

  Read the article

• Iptables - forward email ports?

  - by Emmet Brown

  im trying to open some local ports (LAN) and then re-direct them to another server (WAN) using iptables. Here is my config: #WAN allow-hotplug eth1 auto eth1 iface eth1 inet static #Tarjeta red WAN address 192.168.2.2 gateway 192.168.2.1 netmask 255.255.255.0 #LAN allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.16.6 netmask 255.255.255.0 network 192.168.16.0 broadcast 192.168.16.255 I try this: iptables -A PREROUTING -t nat -i eth0 -p tcp --dport 110 -j DNAT --to 200.40.30.218:110 iptables -A FORWARD -p tcp -i eth0 -o eth1 -d 200.40.30.218 --dport 110 -j ACCEPT iptables -A PREROUTING -t nat -i eth0 -p tcp --dport 25 -j DNAT --to 200.40.30.218:25 iptables -A FORWARD -p tcp -i eth0 -o ethq -d 200.40.30.218 --dport 25 -j ACCEPT but, it did not work. i also try changeing eth0 to eth1 (and eth1 to eth0) but nothing happened. Starting Nmap 5.00 ( http://nmap.org ) at 2011-10-03 14:44 UYST Interesting ports on 192.168.16.6: Not shown: 997 closed ports PORT STATE SERVICE 22/tcp open ssh 111/tcp open rpcbind 8080/tcp open http-proxy Im running debian. Can u guys help me to check what is happening? edit: IPTABLES-SAVE # Generated by iptables-save v1.4.8 on Mon Oct 3 15:43:14 2011 *mangle :PREROUTING ACCEPT [139993:77867651] :INPUT ACCEPT [139385:77761761] :FORWARD ACCEPT [186:12071] :OUTPUT ACCEPT [173556:74341650] :POSTROUTING ACCEPT [173734:74352988] COMMIT # Completed on Mon Oct 3 15:43:14 2011 # Generated by iptables-save v1.4.8 on Mon Oct 3 15:43:14 2011 *nat :PREROUTING ACCEPT [1649:190626] :POSTROUTING ACCEPT [6729:339646] :OUTPUT ACCEPT [6697:337660] -A PREROUTING -i eth0 -p tcp -m tcp --dport 110 -j DNAT --to-destination 200.40.30.218:110 -A PREROUTING -i eth0 -p tcp -m tcp --dport 25 -j DNAT --to-destination 200.40.30.218:25 COMMIT # Completed on Mon Oct 3 15:43:14 2011 # Generated by iptables-save v1.4.8 on Mon Oct 3 15:43:14 2011 *filter :INPUT ACCEPT [138307:77066136] :FORWARD ACCEPT [168:11207] :OUTPUT ACCEPT [172288:73655708] -A FORWARD -d 200.40.30.218/32 -i eth0 -o eth1 -p tcp -m tcp --dport 110 -j ACCEPT -A FORWARD -d 200.40.30.218/32 -i eth0 -o ethq -p tcp -m tcp --dport 25 -j ACCEPT COMMIT # Completed on Mon Oct 3 15:43:14 2011 Regards

  Read the article

• MSSQL 2008 login failed for windows authentication

  - by Force Flow

  I'm running Microsoft SQL 2008 on a Windows 2008 Server. The MSSQL server server authentication is set to SQL Server and Windows Authentication mode. I have created an active directory security group "xyz app users". I have added a normal user (without any active directory admin privledges) and a user with domain admin privledges to the "xyz app users" group. I have added the group to the MSSQL management console as a login user. This group is a member of the public server role and is mapped to two databases. On a workstation, when the normal user is logged in, I configure a DSN ODBC connection, and I'm able to successfully create the DSN and test the SQL connection. However, when I'm logged in as the user with domain admin privledges, when I attempt to configure the DSN ODBC connection, I can't get past the login ID configuration screen. If I select "windows authentication" and click "next", I get an error: Connection failed: SQLState: '28000' SQL Server Error: 18456 [Microsoft][ODBC SQL Server Driver][SQL Server]Login failed for user 'mydomain\myuser' On the server's application event logs, this error appears: Login failed for user 'mydomain\myuser'. Reason: Token-based server access validation failed with an infrastructure error. Check for previous errors. [CLIENT: 172.x.x.x] And in MSSQL's event logs: Error: 18456, Severity: 14, State: 11 Solutions that I've seen so far do not seem to fit this situation (some solutions I've seen are only applicable when the BUILDIN\Administrator is being used locally on the server, which is not the case here).

  Read the article

• Website and file/directory permissions

  - by mathiass

  I've been given a task to fix this one website. One of its issues is that on one page, the images have broken links - the images are not showing, and clicking on the image (i.e. direct link to the image file) results in a 403 (Forbidden) error. I am looking for some feedback on what could be the possible cause. The directory where the images are stored has the following permissions: drwxrws--- www "group" 10240 Aug 2008 "image directory name" I had to hide the names. I checked the page source code, and everything seems to be in place. The rest of the site, and other images outside that image directory are showing fine. I was told that recently there have been some changes to the server. I'm trying to assume that there is no fault in the source code, and the permissions are - or used to be - correct (since the site has been working before, and no recent changes to the site itself have been made). My only thoughts at the moment is that either: a) the directory permission should be: drwxrws--x (executable) for the other users, or b) there is a change in the server settings that I don't know of. Is there anything else I should check?

  Read the article

• Nagios: turn off service checks/display on down hosts

  - by Alien Life Form

  I want to to tweak nagios in such a way that all checking stops (with services not displayed, or displayed as unknown) for any down node. Said differently I only want to see one alert for a down host instead of 1 (down) + n (1 for every service). Note that I am interested in service display/status, not only in turning off notifications. Rationale: we use the nagios firefox/chrome plugin to monitor status and nagios' behavior is too noisy giving readings like these (because every node has 20 services): 3 down, 1 unreachable, 4 warnings, 87 critical This means that the 7 critical services on up node (the problem is on the service) are swamped in a slab of red services which are critical only because they sit on a node that's down/unreachable. What I'd rather like to see is: 3 down, 1 unreachable, 80 unknown, 4 warnings, 7 critical Or even 3 down, 1 unreachable, 4 warnings, 7 critical I have looked in service dependencies but I did not fine a way to describe: "make all services on a alive-host dependen on the status of the host check". I found the problem discussed here, where one of the participants thought it was a nagios bug, and here where one of the participants thought it was "as designed". As things are, I am just interested in the effect, much less in the design philosophy. Note that this nagios is checking hundreds of nodes, so the maintainablilty of the solution is also important. TIA and cheers.

  Read the article

• Understanding MySQL Query Caches and when to implement it?

  - by Jeff

  On our current MySQL server query cache is enabled. Qchache_hits: 31913 Qchache_inserts: 50959 Qchache_lowmem_prunes: 9320 Qchache_not_chached: 209320 Qchache_queries_in_chace: 986 com_update: 0 com_delete: 0 I do not fully understand the Query cache - I am reading about it currently and trying to understand it. Our database holds inventory data, customer data, employee data, sales data and so forth. The query is very rarely run more than once. The possibility of a query being run twice is viewing a specific sales information twice. But basically everything in our system changes constantly. It is always being updated, deleted, insterted and off the top of my head I can't picture users running the same query twice within a week. Do I even need to have the query cache enabled? I am guessing that the inserts means 51k entries have been added, but only 986 of those are being stored? Would an idea be to refresh the cache, and watch it for a week and check how many of the queries in cached are accessed maybe on a weekly basis to see if it is actually returning any benefits? Any help/guidance on this is appreciated, thanks

  Read the article

< Previous Page | 652 653 654 655 656 657 658 659 660 661 662 663  | Next Page >