Search Results

Search found 18191 results on 728 pages for 'single board'.

Page 656/728 | < Previous Page | 652 653 654 655 656 657 658 659 660 661 662 663  | Next Page >

• Rsync over ssh: "ERROR: module is read only" suddenly appeared

  - by user978548

  I've used from some time rsync/ssh to backup my shared host contents to my personal Synology NAS (212j for that matter), and it worked quite well. For information, I use a password-less ssh connection. 3 days ago, I updated my NAS software and since (or at least I believe it's since that), the backup won't work anymore. I get the following error on the host: rsync: writefd_unbuffered failed to write 4 bytes to socket [sender]: Broken pipe (32) ERROR: module is read only ..which I do not understand. beside that nothing changed that I know of in both source and destination that can be related to rsync or ssh, I did check a few things and all seems to be alright: I can still connect through ssh from the host to my NAS with the good user, so ssh stuff like keys haven't changed. I also have the correct file permissions on the NAS (I checked, and also tried to create files, directories, .. with the user used by rsync through ssh). I read here and there that the error means that I have to ensure that my rsyncd.conf have the right read only = no in it, but as far as I know, I never used rsyncd as well as I never configured anything for it and until now it worked like a charm.. I use the following command to do the backup: rsync -ab --recursive \ --files-from="$FILES_FROM" \ --backup-dir=backup_$SUFFIX \ --delete \ --filter='protect backup_*' \ $WDIRECTORY/ \ remote_backup:$REMOTE_BACKUP/ So I'm stuck and really can't figure out what happened. Edit: As suggested in comments, I also tried passing commands to ssh (but not from inside a ssh session), that worked as expected, and also tried a single rsync command, which didnt worked, failing just like the complete backup command. (sharedHost):hostuser:~ > touch test.txt (sharedHost):hostuser:~ > rsync test.txt remote_backup:backups/test.txt ERROR: module is read only rsync error: syntax or usage error (code 1) at main.c(1034) [Receiver=3.0.8] rsync: connection unexpectedly closed (9 bytes received so far) [sender] rsync error: error in rsync protocol data stream (code 12) at io.c(601) [sender=3.0.7] and (sharedHost):hostuser:~ > ssh remote_backup 'touch /abs_path_to_backups/backups/test2.txt && echo "ProoF" > /abs_path_to_backups/backups/test2.txt' (sharedHost):hostuser:~ > ssh remote_backup 'cat /abs_path_to_backups/backups/test2.txt' ProoF

  Read the article

• hosting 2 webapps under 1 apache/tomcat

  - by mkoryak

  I am trying to host multiple webapps under tomcat 6 behind apache2 via mod_jk. I am at my wits end with this. the problem i am facing that both domains seems to point to a single tomcat 'domain'. my server.xml looks like this: <Service name="Catalina"> <Connector port="8080" protocol="HTTP/1.1" connectionTimeout="20000" URIEncoding="UTF-8" redirectPort="8443" /> <Connector port="8009" protocol="AJP/1.3" redirectPort="8443" /> <Connector port="8010" protocol="AJP/1.3" redirectPort="8443" /> <Engine name="Catalina" defaultHost="dogself.com"> <Realm className="org.apache.catalina.realm.UserDatabaseRealm" resourceName="UserDatabase"/> <Host name="dogself.com" appBase="webapps-dogself" unpackWARs="true" autoDeploy="true" xmlValidation="false" xmlNamespaceAware="false"> </Host> <Host name="natashacarter.com" appBase="webapps-natashacarter.com" unpackWARs="true" autoDeploy="true" xmlValidation="false" xmlNamespaceAware="false"> </Host> </Engine> </Service> my workers.properties looks like this: worker.list=dogself,natashacarter worker.dogself.port=8009 worker.dogself.host=dogself.com worker.dogself.type=ajp13 worker.natashacarter.port=8010 worker.natashacarter.host=natashacarter.com worker.natashacarter.type=ajp13 finally my apache vhosts look like this: <VirtualHost 69.164.218.75:80> ServerName dogself.com DocumentRoot /srv/www/dogself.com/public_html/ ErrorLog /srv/www/dogself.com/logs/error.log CustomLog /srv/www/dogself.com/logs/access.log combined JkMount /* dogself </VirtualHost> and <VirtualHost 69.164.218.75:80> ServerName natashacarter.com DocumentRoot /srv/www/dogself.com/public_html/ ErrorLog /srv/www/dogself.com/logs/error.log CustomLog /srv/www/dogself.com/logs/access.log combined JkMount /* natashacarter </VirtualHost> when i log into manager webapp on both dogself.com and natashacarter.com, i can deploy to a context path on dogself, and that same contextpath will appear on natashacarter - so i know for a fact that this is the same tomcat domain. edit: just found this in my mod_jk log [Sun Feb 20 21:15:43 2011] [28546:3075521168] [warn] map_uri_to_worker_ext::jk_uri_worker_map.c (962): Uri * is invalid. Uri must start with / [Sun Feb 20 21:16:44 2011] [28548:3075521168] [info] ajp_send_request::jk_ajp_common.c (1496): (dogself) all endpoints are disconnected, detected by connect check (1), cping (0), send (0) but not sure why dogself wouldnt respond please help a brother out

  Read the article

• OS X server large scale storage and backup

  - by user135217

  I really hope this question doesn't come across as trolling or asking for buying advice. It's not intended. I've just started working for a small ad agency (40 employees). I actually quit being a system administrator a few years ago (too stressful!), but the company we're currently outsourcing our IT stuff to is doing such a bad job that I've felt compelled to get involved and do what I can to improve things. At the moment, all the company's data is stored on an 8TB external firewire drive attached to a Mac Mini running OS X Server 10.6, which provides filesharing (using AFP) for the whole company. There is a single backup drive, which is actually a caddy containing two 3TB hard drives arranged in RAID 0 (arrggghhhh!), which someone brings in as and when and copies over all the data using Carbon Copy Cloner. That's the entirety of the infrastructure, and the whole backup and restore strategy. I've been having sleepless nights. I've just started augmenting the backup process with FreeBSD, ZFS, sparse bundles and snapshot sends to get everything offsite. I think this is a workable behind the scenes solution, but for people's day to day use I'm struggling. Given the quantity and importance of the data, I think we should really be looking towards enterprise level storage solutions, high availability and so on, but the whole company is all Mac all the time, and I cannot find equipment that will do what we need. No more Xserve; no rack storage; no large scale storage at all apart from that Pegasus R6 that doesn't seem all that great; the Mac Pro has fibre channel, but it's not a real server and it's ludicrously expensive; Xsan looks like it's on the way out; things like heartbeatd and failoverd have apparently been removed from Lion Server; the new Mac Mini only has thunderbolt which severely limits our choices; the list goes on and on. I'm really, really not trying to troll here. I love Macs, but I just genuinely don't know where I'm supposed to look for server stuff. I have considered Linux or FreeBSD and netatalk for serving files with all the server-y goodness those OSes bring, but some the things I've read make me wonder if it's really the way to go. Also, in my own (admittedly quite cursory) experiments with it, I've struggled to get decent transfer speeds. I guess there's also the possibility of switching everyone off AFP and making them use SMB or NFS, but I understand that this can cause big problems with resource forks and file locks. I figure there must be plenty of all Mac companies out there. If you're the sysadmin at one, what do you use? Any suggestions very gratefully received.

  Read the article

• Innodb Queries Slow

  - by user105196

  I have redHat 5.3 (Tikanga) with Mysql 5.0.86 configued with RIAD 10 HW, I run an application inquiries from Mysql/InnoDB and MyIsam tables, the queries are super fast,but some quires on Innodb tables sometime slow down and took more than 1-3 seconds to run and these queries are simple and optimized, this problem occurred just on innodb tables in different time with random queries. Why is this happening only to Innodb tables? the below is the Innodb status and some Mysql variables: show innodb status\G ************* 1. row ************* Status: 120325 10:54:08 INNODB MONITOR OUTPUT Per second averages calculated from the last 19 seconds SEMAPHORES OS WAIT ARRAY INFO: reservation count 22943, signal count 22947 Mutex spin waits 0, rounds 561745, OS waits 7664 RW-shared spins 24427, OS waits 12201; RW-excl spins 1461, OS waits 1277 TRANSACTIONS Trx id counter 0 119069326 Purge done for trx's n:o < 0 119069326 undo n:o < 0 0 History list length 41 Total number of lock structs in row lock hash table 0 LIST OF TRANSACTIONS FOR EACH SESSION: ---TRANSACTION 0 0, not started, process no 29093, OS thread id 1166043456 MySQL thread id 703985, query id 5807220 localhost root show innodb status FILE I/O I/O thread 0 state: waiting for i/o request (insert buffer thread) I/O thread 1 state: waiting for i/o request (log thread) I/O thread 2 state: waiting for i/o request (read thread) I/O thread 3 state: waiting for i/o request (write thread) Pending normal aio reads: 0, aio writes: 0, ibuf aio reads: 0, log i/o's: 0, sync i/o's: 0 Pending flushes (fsync) log: 0; buffer pool: 0 132777 OS file reads, 689086 OS file writes, 252010 OS fsyncs 0.00 reads/s, 0 avg bytes/read, 0.00 writes/s, 0.00 fsyncs/s INSERT BUFFER AND ADAPTIVE HASH INDEX Ibuf: size 1, free list len 366, seg size 368, 62237 inserts, 62237 merged recs, 52881 merges Hash table size 8850487, used cells 3698960, node heap has 7061 buffer(s) 0.00 hash searches/s, 0.00 non-hash searches/s LOG Log sequence number 15 3415398745 Log flushed up to 15 3415398745 Last checkpoint at 15 3415398745 0 pending log writes, 0 pending chkp writes 218214 log i/o's done, 0.00 log i/o's/second BUFFER POOL AND MEMORY Total memory allocated 4798817080; in additional pool allocated 12342784 Buffer pool size 262144 Free buffers 101603 Database pages 153480 Modified db pages 0 Pending reads 0 Pending writes: LRU 0, flush list 0, single page 0 Pages read 151954, created 1526, written 494505 0.00 reads/s, 0.00 creates/s, 0.00 writes/s No buffer pool page gets since the last printout ROW OPERATIONS 0 queries inside InnoDB, 0 queries in queue 1 read views open inside InnoDB Main thread process no. 29093, id 1162049856, state: waiting for server activity Number of rows inserted 77675, updated 85439, deleted 0, read 14377072495 0.00 inserts/s, 0.00 updates/s, 0.00 deletes/s, 0.00 reads/s END OF INNODB MONITOR OUTPUT 1 row in set, 1 warning (0.02 sec) read_buffer_size = 128M sort_buffer_size = 256M tmp_table_size = 1024M innodb_additional_mem_pool_size = 20M innodb_log_file_size=10M innodb_lock_wait_timeout=100 innodb_buffer_pool_size=4G join_buffer_size = 128M key_buffer_size = 1G can any one help me ?

  Read the article

• Impact of the L3 cache on performance - worth a dual-processor system?

  - by Dan Nissenbaum

  I will be purchasing a new high-end system, and I would like to have a better sense of whether a dual-processor Xeon system (I am looking at the new, high-end Xeon E5-2687W) might, realistically, provide a noticeable performance improvement due to the doubling of the L3 cache (20 MB per CPU). (This is in addition to the occasional added advantage due to the doubling of cores and RAM.) My usage scenario is, roughly, that I have many background applications running at any time - 3 or 4 data compression/backup applications, a low-impact web server, one or two virtual machines at any given time (usually fairly idle), and perhaps 20 utility programs that utilize a noticeable (but small) portion of the CPU cores. In total, when I am not actively using the computer, about 25% of the total CPU power is utilized in my current i7-970 6-core (12 thread) system. When I am doing routine work, the CPU utilization often exceeds 50%, and occasionally hits 75%-80%. The Xeon E5-2687W is not only a second-generation i7 (so should improve performance for that reason), but also has 8 cores (16 threads), rather than 6 cores. For this reason, I expect to run into the 75% CPU range even less frequently. Nonetheless, the ability to double the cores and the RAM is a consideration. However, in the end, I believe this decision comes down to whether the doubling of the L3 cache will provide a noticeable improvement. There are many benchmarks, and a lot of discussion, regarding CPU power. However, I find very little discussion of L3 cache utilization, and how increases in the L3 cache (such as doubling it with dual processors) affect performance. For example: If there are only two processes running, but each benefits from a large L3 cache (such as might be the case for background processes that frequently scan the file system), perhaps the overall system performance might noticeably improve with dual CPU's - even if only a single core is active on each CPU - due to each process having double the effective L3 cache. I am hoping that someone has a sense of the benefits of increasing (or doubling) the L3 cache size. Note: the CPU I am considering (the Xeon E5-2687W) has 20 MB L3 cache, so a system with dual CPU's would have 40 MB L3 cache.

  Read the article

• What part of SMF is likely broken by a hard power down?

  - by David Mackintosh

  At one of my customer sites, the local guy shut down their local Solaris 10 x86 server, pulled the power inputs, moved it, and now it won’t start properly. It boots and then presents a prompt which lets you log in. This appears to be single user milestone (or equivalent). Digging into it, I think that SMF isn’t permitting the system to go multi-user. SMF was generating a ton of errors on autofs, after some fooling with it I got it to generate errors on inetd and nfs/client instead. This all tells me that the problem is in some SMF state file or database that needs to be fixed/deleted/recreated or something, but I don’t know what the actual issue is. By “generate errors”, I mean that every second I get a message on the console saying “Method or service exit timed out. Killing contract <#.” This makes interacting with the computer difficult. Running svcs –xv shows the service as “enabled”, in state “disabled”, reason “Start method is running”. Fooling with svcadm on the service does nothing, except confirm that the service is not in a Maintenance state. Logs in /lib/svc/log/$SERVICE just tell you that this loop has been happening once per second. Logs in /etc/svc/volatile/$SERVICE confirm that at boot the service is attempted to start, and immediately stopped, no further entries. Note that system-log isn’t starting because system-log depends on autofs so I have no syslog or dmesg. Googling all these terms ends up telling me how to debug/fix either autofs or nfs/client or inetd or rpc/gss (which was the dependency that SMF was using as an excuse to prevent nfs/client from “starting”, it was claiming that rpc/gss was “undefined” which is incorrect since this all used to work. I re-enabled it with inetadm, but inetd still won’t start properly). But I think that the problem is SMF in general, not the individual services. Doing a restore_repository to the “manifest_import” does nothing to improve, or even detectibly change, the situation. I didn’t use a boot backup because the last boot(s) were not useful. I have told the customer that since the valuable data directories are on a separate file system (which fsck’s as clean so it is intact) we could just re-install solaris 10 on the / partition. But that seems like an awfully windows-like solution to inflict on this problem. So. Any ideas what piece is broken and how I might fix it?

  Read the article

• BIND DNS server (Windows) - Unable to access my local domain from other computers on LAN

  - by Ricardo Saraiva

  I have a BIND DNS server running on my Windows 7 development machine and I'm serving pages with WAMPSERVER. My ideia is to develop some tools (in PHP) for my intranet at work and I want them to be accessible via LAN in this format: http://tools.mycompany.com I've already placed BIND and I can access http://tools.mycompany.com on the machine that holds BIND server, but I cannot access it from other LAN computers. I've done the following on my router: defined static IP's for all LAN computers set Port Forwarding to my server (remember: it serves DNS and Web pages) set DNS server configuration to point to my LAN server On LAN computers, I went to Local Area Network properties and also changed the DNS server IP in order to point to my local DNS server. If it helps, here is my named.conf file: options { directory "c:\windows\SysWOW64\dns\etc"; forwarders {127.0.0.1; 8.8.8.8; 8.8.4.4;}; pid-file "run\named.pid"; allow-transfer { none; }; recursion no; }; logging{ channel my_log{ file "log\named.log" versions 3 size 2m; severity info; print-time yes; print-severity yes; print-category yes; }; category default{ my_log; }; }; zone "mycompany.com" IN { type master; file "zones\db.mycompany.com.txt"; allow-transfer { none; }; }; key "rndc-key" { algorithm hmac-md5; secret "qfApxn0NxXiaacFHpI86Rg=="; }; controls { inet 127.0.0.1 port 953 allow { 127.0.0.1; } keys { "rndc-key"; }; }; ...and a single zone I've defined - file db.mycompany.com.txt: $TTL 6h @ IN SOA tools.mycompany.com. hostmaster.mycompany.com. ( 2014042601 10800 3600 604800 86400 ) @ NS tools.mycompany.com. tools IN A 192.168.1.4 www IN A 192.168.1.4 On the file above 192.168.1.4 is the IP of the local machine inside my LAN. Can someone help me here? I need my web pages to be accessible from other computers inside my LAN using my custom domain name. I've tried on other computers and they can access my server via http://192.168.1.4/, but no able when using http://tools.mycompany.com . Please, consider the following: I'm completely new to BIND I have basic knowledge in Apache configuration Thanks a lot for your help.

  Read the article

• HTTPS request to a specific load-balanced virtual host (using Shibboleth for SSO)?

  - by Gary S. Weaver

  In one environment, we have three servers load balanced that have a single Tomcat instance on each, fronted by two different Apache virtual hosts. Each of those two virtual hosts (served by all three servers) has its own different load balancer. Internally, the first host (we'll call it barfoo) is served by port 443 (HTTPS) with its cert and the second host (we'll call it foobar) is served by port 1443 (HTTPS). When you hit foobar, it goes to the load balancer which is using IP affinity for that host, so you can easily test login/HTTPS on one of the servers serving foobar, but not the others (because you keep getting that server for the lifetime of the LB session, iirc). In addition, each of the servers are using Shibboleth v2 for authN/SSO, using mod_shib (iirc). So, a normal request to foobar hits the LB, is directed to the 3rd server (and will do that from then on for as long as the LB session lasts), then Apache, then to the Shibboleth SP which looks at the request, makes you login via negotiation with the Shibboleth IdP, then you hit Apache again which in turn hits Tomcat, renders, and returns the response. (I'm leaving out some steps there.) We'd like to hit one of the individual servers (foobar-03.acme.org which we'll say has IP 1.2.3.4) via HTTPS (skipping the load balancer), so we at first try putting this in /etc/hosts: 1.2.3.4 foobar.acme.org But since foobar.acme.org is a secondary virtual host running on 1443, it attempts to get barfoo.acme.org rather than foobar.acme.org at port 1443 and see that the cert for barfoo.acme.org is invalid for this case since it doesn't match the request's host, foobar.acme.org. I thought an ssh tunnel might be easy enough, so I tried: ssh -L 7777:foobar-03.acme.org:1443 [email protected] I tried just hitting https://localhost:7777/webappname in a browser, but when the Shibboleth login is over, it again tries to redirect to barfoo.acme.org, which is the default host for 443, and we get into an infinite redirect loop. I then tried setting up an SSH tunnel with privileged port 443 locally going to 443 of foobar-03.acme.org as the hostname for that virtual host: sudo ssh -L 443:foobar-03.acme.org:1443 [email protected] I also edited /etc/hosts to add: 127.0.0.1 foobar.acme.org This finally worked and I was able to get the browser to hit the individual HTTPS host at https://foobar.acme.org/webappname, bypassing the load balancer. This was a bit of a pain and wouldn't work for everyone, due to the requirement to use the local 443 port and ssh to the server. Is there an easier way to browse to and log into an individual host in this case?

  Read the article

• How to Setup Ubuntu Mail Server with Google Apps?

  - by Apreche

  I have a domain, let's call it foobar.com. All of the MX records for foobar.com point to Google's mail servers because I am using Google Apps for your domain to manage it. It's great because everyone gets all the advantages of GMail, but our e-mail addresses aren't @gmail.com. I also have a server. Primarily, it's a web server, but it also serves other things. One of the things it serves is the web site for foobar.com and also sites for various virtual hosts such as shop.foobar.com and forum.foobar.com. The server is running Ubuntu 8.04, because I like using LTS releases in production. The thing is, there are various applications running on the server that need the ability to send out emails. Various applications, like the cron jobs, send me e-mails in case of errors. Some of the web applications need to send e-mail to users when they forget their passwords, to confirm new registered users, etc. Lastly, it's nice to be able to send e-mail from the command line using the mail command, or mutt. How can I setup the mail on the web server to go through the Google apps mail servers? I don't need the web server to receive mail, though that would be cool. I do need it to be able to send mail as any legitimate address @foobar.com. That way the forum application can send mails with [email protected] in the from field, and the ecommerce application will have [email protected] in the from field. Also, by sending the mail through the Google servers, we can avoid a lot of the problems with the e-mails being blocked by various spam filters on the web. Google's SMTP servers are trusted a lot more than mine would be. I'm pretty good with administering Linux systems, but I am absolutely brain dead when it comes to e-mail. I need step by step directions from beginning to end on how to set this up. I need to know every thing to install, and every single change to the configuration files that is necessary. I have tried following various howtos and guides in the past, but none of them were quite right. Either they didn't work at all, or they offered a configuration that is not what I wanted. Please help. Thanks.

  Read the article

• DPM 2010 PowerShell Script to Easily Restore Multiple Files

  - by bmccleary

  I’ve got what I thought would be a simple task with Data Protection Manager 2010 that is turning out to be quite frustrating. I have a file server on one server and it is the only server in a protection group. This file server is the repository for a document management application which stores the files according to the data within a SQL database. Sometimes users inadvertently delete files from within our application and we need to restore them. We have all the information needed to restore the files to include the file name, the folder that the file was stored in and the exact date that the file was deleted. It is easy for me to restore the file from within the DPM console since we have a recovery point created every day, I simply go to the day before the delete, browse to the proper folder and restore the file. The problem is that using the DPM console, the cumbersome wizard requires about 20 mouse clicks to restore a single file and it takes 2-4 minutes to get through all the windows. This becomes very irritating when a client needs 100’s of files restored… it takes all day of redundant mouse clicks to restore the files. Therefore, I want to use a PowerShell script (and I’m a novice at PowerShell) to automate this process. I want to be able to create a script that I pass in a file name, a folder, a recovery point date (and a protection group/server name if needed) and simply have the file restored back to its original location with some sort of success/failure notification. I thought it was a simple basic task of a backup solution, but I am having a heck of a time finding the right code. I have seen the sample code at http://social.technet.microsoft.com/wiki/contents/articles/how-to-use-a-windows-powershell-script-to-recover-an-item-in-data-protection-manager.aspx that I have tried to follow, but it doesn’t accomplish what I really want to do (it’s too simplistic) and there are errors in the sample code. Therefore, I would like to get some help writing a script to restore these files. An example of the known values to restore the data are: DPM Server: BACKUP01 Protection Group: Document Repository Data Protected Server: FILER01 File Path: R:\DocumentRepository\ToBackup\ClientName\Repository\2010\07\24\filename.pdf Date Deleted: 8/2/2010 (last recovery point = 8/1/2010) Bonus Points: If you can help me not only create this script, but also show me how to automate by providing a text file with the above information that the PowerShell script loops through, or even better, is able to query our SQL server for the needed data, then I would be more than willing to pay for this development.

  Read the article

• libreadline history lines combine

  - by jettero

  This has been driving me crazy for about three years. I don't know how to fully describe the problem, but I think I can finally describe a way to recreate it. Your milage may vary. I have a mixture of ubuntu server and desktop machines of various versions and a few gentoo machines with various states of disrepair. They all seem to kindof do their own thing, although with similarities. Try this and let me know if you see the same thing. pop open two xterms (TERM=xterm) resize one so they're not the same issue screen -R test1 in one (TERM=screen) and screen -x test1 in the other hooray, typing in one shows up in the other; although notice that their different size produces artifacts and things issue a couple commands in your shell hit ^AF in the one that doesn't fit quite right, now it fits!! scroll back over the history a little goto 6 Eventually you'll notice a couple history lines combine. If you don't, then it's something unique to my setup, which spans various distributions and computers; so that's a confusing concept to me. If you see the thing I'm seeing then this: bash$ ls -al bash$ ps auxfw becomes this: bash$ ls -al; ps auxfw It doesn't happen every time. I have to really play with it — unless I don't want it to happen, then it always does. On some systems (or combinations), I get a line separator like the example above. On some systems, I do not. That I get the line separator on some systems seems to indicate to me that bash supports this behavior. Its history is entirely handled by libreadline and after perusing (ie, carefully reading) the man pages, I couldn't find a single readline setting for combining two history lines. Nor can I find anything in the bash manpage. So, how can I invoke this on purpose? Or, if I can't do that, how can I disable it completely? I would take either answer as a solution. Currently, I only see it when I don't want it.

  Read the article

• How to enjoy DVD on Apple iPad

  - by user44251

  I believe many people spent a sleepless night yesterday waiting for the new Apple Tablet to come, just a few days ago or perhaps longer I noticed fierce debate about it, its name, size, capacity, processor, main features, price etc. And now, they can take a long breath with the new Apple Tablet named iPad officially released on 28, January, 2010 (Beijing Time). But I know a new battle just begins. iPad, sounds somewhat like iPod and it really shares some similarities in terms of shape like smart, light and portable. It has a 9.7-inch, LED-backlit, IPS display with a remarkable precise Multi-Touch screen. And yet, at just 1.5 lbs and 0.5 inches thin, it's easy to carry and use everywhere. It can greatly facilitates your experience with the web, emails, photos and videos. Right now, it can run almost 140.000 of the apps on the Apple store. It can even run the apps you have downloaded for your iPhone or iPod touch. But so far, I haven't seen any possibility that it can work with DVD, probability there is no built-in DVD-ROM or DVD player which can play DVD directly. As Apple iPad states, the video formats supported are MPEG-4 (MP4, M4V), H.264, MOV etc and audio formats accepted are AAC, Proteceted AAC, MP3, AIFF and WAV etc, those are formats that are commonly used with iMac. This could really a hard nut to crack if you want to watch your favourite DVD on this magic Apple iPad. But don't worry, there is still way out, you just need a few steps for ripping and importing DVD movies to Apple iPad with a simple application DVD to iPad converter What's on DVD to iPad Converter for Mac DVD to iPad converter for Mac is a powerful and professional application designed for the newly released Apple iPad which can rip, convert your DVD contents to Apple iPad compatible MPEG-4 (MP4, M4V), H.264, MOV etc, and other popular file formats like AVI, WMV, MPG, MKV, VOB, 3GP, FLV etc can also be converted so that you can put on your portable devices like iPod, iPhone, iRiver, BlackBerry etc. Besides, it can also extract audio from DVD videos and save as MP3, AIFF, AAC, WAV etc. Mac DVD to iPad converter has also been enhanced that can run both on PowerPC and Intel (Snow Leopard included). It can offer versatile editing features which allows you to make your own DVD videos. For example, you can cut your DVD to whatever length you like by Trim, crop off unwanted parts from DVD clips by Crop, add special effect like Gray, Emboss and Old film to make your videos more artistic. Besides, its built-in merging feature and batch mode allows you to join several DVD clips into a single one and do batch conversion. And more features can be expected if you afford a few minutes to try.

  Read the article

• What the best way to recover from when your RAID H/W incorrectly thinks a disk is missing

  - by Software Monkey

  I have a Windows 7 system with an MSI motherboard (running the latest AMD BIOS) and two of my four disks (not the system boot disk) configured via the Mobo as RAID-1. After a normal system restart today, the RAID BIOS reports that one of the two drives has been disconnected or has failed. It's not really failed; via recovery tools I can verify that if I take the BIOS out of RAID mode. But I can find no way to re-add the second hard disk to the array and rebuild via the BIOS - the only option seems be to delete the array and recreate it, but I've done that once before and it blows away the disk. It's done this once before, however on a subsequent reboot after double-checking the drive cabling (but not changing anything) and it boot up fine. So I think the mobo RAID is a little bit flaky. At this point I would like to remove the RAID drivers, change to AHCI mode and switch over to using a Windows 7 dynamic mirror disk. But the RAID drivers seem somehow deeply bound into the Windows startup - I can't find anything like the good ol' safe-mode in Windows 7. If I boot from the Win 7 install disk in ACHI mode I can use recovery tools to log in to the Windows 7 installation, so the boot drive it seems fine with ACHI mode. Additionally, I can see all my other disks, run chkdsk on them and they seem to be fine. If I try to boot from the HDD in AHCI mode, it just reboots part way through, presumably because the RAID drivers load and conflict with the BIOS being set to AHCI. So: How do I strip the RAID drivers from my Win 7 installation? If I delete the RAID logical disk, will it really delete partitioning information, or is that just a poorly worded message when it says the data on the disk will be deleted? If I disconnect the 2 disks in a RAID array, then delete the logical disk array, and then reconnect and reboot still in RAID mode, will the disks simply revert to RAID single-disks like my other 2 and then maybe I can leave windows with RAID drivers by operate the disks as singles with 2 of them in a Windows dynamic disk mirrored setup? Does Windows 7 have anything like the Windows XP Repair Install, where it will reinstall the O/S binaries from CD, but leave apps and setup alone. I am really hoping I don't have to do a complete reinstall of Windows 7 - the last one, when I upgraded from XP, took me two days to get everything set up and installed.

  Read the article

• Vista stuck at "Shutting down..." screen. Any way to get verbose logging?

  - by CapBBeard

  Hi all, My home machine has been running fine for about 3 years, no problems at all. Within the last couple of weeks it's had real trouble trying to shut down. It'll get so far and then just sit there at the "Shutting down..." screen for hours. I've left it overnight, I've tried in safe mode, all to no avail. These days, I just wait for the disk activity to finish up and then hold the power button to turn it off. Feels dirty as, especially because there's a RAID involved! The hardware itself is in pretty good shape and of decent spec; Core 2 Quad, 4GB RAM, 1TB RAID 1+0, so it's not quite like a 7 year old PC coming to end of life! In the last month, hardware hasn't changed except for a new monitor. Admittedly I haven't tried unplugging the monitor but I've never heard of that preventing a shutdown. I might give it a whirl later I guess, as a last resort. I've uninstalled old apps, done updates, checked the event log, looked in device manager, uninstalled all non-present devices, disabled various non-critical devices (imaging, audio etc), unplugged peripherals, stopped non-essential services, unplugged the network, disabled the network adapter entirely, ran chkdsk, verified my RAID, the list goes on. But not a single lead. I'm pretty stumped. It could be hardware, but I have no other evidence to suggest so; when the PC is running, it runs fine. Temperatures are good, gaming is smooth as always, disk performance is fine. Event log even makes it look like the shutdown was completed (gets to the point where the event log service stops). In fact, the PC doesn't appear to realise that I cut the power to it. So my question is, does anyone know if there is a way I can get some verbose output (or a log) from shutdown to give me some idea of what is causing the issue? I'm guessing it's stuck unloading some app/driver but it would be good to get some specifics! Unless anyone has any other ideas? I suspect a reinstall would resolve the issue, however I'm looking to get a new PC built in the next month or so, and the reinstall is going to be quite a big job so I'd rather just wait until then if it comes to that. Would still be nice to get this sorted in the mean time though. Cheers!

  Read the article

• How to rate-limit concurrent sessions with nginx or haproxy?

  - by bantic

  I'm currently using nginx to reverse-proxy requests from web clients that are doing long-polling to an upstream. Since we're doing long polling (as opposed to websockets), when a client connects it will make multiple http connections to the server in serial, re-establishing a connection every time the server sends it some data (or timing out and re-establishing if the server has nothing to say for 10 seconds). What I'd like to do is limit the number of concurrent web clients. Since the clients are constantly making new HTTP requests instead of keeping a single request open, it's a little tricky to count the total number of web clients (because it's not the same as total number of concurrently connected http clients). The method I've come up with is to track http requests by the originating IP address, and store the IP address somewhere with a TTL of 20 seconds. If a request comes in whose IP isn't recognized, then we check the total number of unexpired stored IP addresses; if that's less than the maximum then we allow this request through. And if a request comes in with an IP address that we can find in the look-up table that hasn't yet expired, then it is allowed through as well. All requests that are allowed through have their IPs added to the table (if not there before) and the TTL refreshed to 20 seconds again. I had actually whipped something together that worked correctly this way using nginx along with the Redis 2.0 Nginx Module (and the nginx lua module to simplify the conditional branching), using redis to store my IP addresses with a TTL (the SETEX command), and checking the table size with the DBSIZE command. This worked but the performance was horrible. nginx and redis ended up using lots of cpu and the machine could only handle a very small number of concurrent requests. The new stick-table and tracking counters that were added to Haproxy in version 1.5 (via a commission from serverfault) seem like they might be ideal to implement exactly this sort of rate limiting, because the stick-table can track IP addresses and automatically expire entries. However, I don't see an easy way to get a total count of the unexpired entries in the stick table, which would be necessary to know the number of connected web clients. I'm curious if anyone has any suggestions, for nginx or haproxy or even for something else not mentioned here that I haven't thought of yet.

  Read the article

• Nvidia Drivers on Debian / Lenny (Stable) -> Installation successful -> Monitors gets black

  - by David

  I have successfully installed the proprietary drivers for my nvidia (geforce 7300 gt) graphics card on debian/lenny. I know its not the best way to chose for driver installation ( see this link: http://wiki.debian.org/NvidiaGraphicsDrivers#non-freedrivers ). but the two ways seem to be possible for me (nvidia-kernel module compilation). Now the problem is that the monitors gets black, the power light starts blinking after i launch the x-server. Have a short look a the logs (output truncated from /var/log/Xorg.0.log): (II) Setting vga for screen 0. (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32 (==) NVIDIA(0): RGB weight 888 (==) NVIDIA(0): Default visual is TrueColor (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0) (**) Jul 28 17:10:11 NVIDIA(0): Enabling RENDER acceleration (II) Jul 28 17:10:11 NVIDIA(0): Support for GLX with the Damage and Composite X extensions is (II) Jul 28 17:10:11 NVIDIA(0): enabled. (II) Jul 28 17:10:11 NVIDIA(0): NVIDIA GPU GeForce 7300 GT (G73) at PCI:1:0:0 (GPU-0) (--) Jul 28 17:10:11 NVIDIA(0): Memory: 262144 kBytes (--) Jul 28 17:10:11 NVIDIA(0): VideoBIOS: 05.73.22.25.00 (II) Jul 28 17:10:11 NVIDIA(0): Detected PCI Express Link width: 16X (--) Jul 28 17:10:11 NVIDIA(0): Interlaced video modes are supported on this GPU (--) Jul 28 17:10:11 NVIDIA(0): Connected display device(s) on GeForce 7300 GT at PCI:1:0:0: (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (CRT-0) (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0) (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (CRT-0): 400.0 MHz maximum pixel clock (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0): 165.0 MHz maximum pixel clock (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0): Internal Single Link TMDS (II) Jul 28 17:10:11 NVIDIA(0): Assigned Display Device: CRT-0 (==) Jul 28 17:10:11 NVIDIA(0): (==) Jul 28 17:10:11 NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select" (==) Jul 28 17:10:11 NVIDIA(0): will be used as the requested mode. (==) Jul 28 17:10:11 NVIDIA(0): (II) Jul 28 17:10:11 NVIDIA(0): Validated modes: (II) Jul 28 17:10:11 NVIDIA(0): "nvidia-auto-select" (II) Jul 28 17:10:11 NVIDIA(0): Virtual screen size determined to be 1280 x 1024 (--) Jul 28 17:10:11 NVIDIA(0): DPI set to (85, 86); computed from "UseEdidDpi" X config (--) Jul 28 17:10:11 NVIDIA(0): option (==) Jul 28 17:10:11 NVIDIA(0): Enabling 32-bit ARGB GLX visuals. (--) Depth 24 pixmap format is 32 bpp Here is the complete /etc/X11/xorg.conf file as generated by nvidia-xconfig: # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:59 PDT 2010 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" EndSection Section "Module" Load "dbe" Load "extmod" Load "type1" Load "freetype" Load "glx" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" Hor

  Read the article

• Why does writing a file to an NFS share send a COMMIT operation to the NFS server?

  - by Antonis Christofides

  I have a Debian squeeze (2.6.32-5-amd64) which is at the same time a NFS4 server and client (it mounts itself through NFS4). The local directory that leads directly to disk is /nfs4exports/mydir, whereas /nfs4mounts/mydir is the same thing mounted through NFS, using the machine's external IP address. Here is the line from fstab: 192.168.1.75:/mydir /nfs4mounts/mydir nfs4 soft 0 0 I have an application that writes many small files. If I write directly to /nfs4exports/mydir, it writes thousands of files per second; but if I write to /nfs4mounts/mydir, it writes 4 files per second or so. I can greatly increase speed if I add async to /etc/exports. (Writing a single large file to the NFS-mounted directory goes at more than 100 MB/s.) I examine the server statistics and I see that whenever a file is written, it is "committed" (this also happens with NFSv3): root@debianvboxtest:~# mount -t nfs4 192.168.1.75:/mydir /mnt root@debianvboxtest:~# nfsstat|grep -A 2 'nfs v4 operations' Server nfs v4 operations: op0-unused op1-unused op2-future access close commit 0 0% 0 0% 0 0% 10 4% 1 0% 1 0% root@debianvboxtest:~# echo 'hello' >/mnt/test1056 root@debianvboxtest:~# nfsstat|grep -A 2 'nfs v4 operations' Server nfs v4 operations: op0-unused op1-unused op2-future access close commit 0 0% 0 0% 0 0% 11 4% 2 0% 2 0% Now in the RFC, I read this: The COMMIT operation is similar in operation and semantics to the POSIX fsync(2) system call that synchronizes a file's state with the disk (file data and metadata is flushed to disk or stable storage). COMMIT performs the same operation for a client, flushing any unsynchronized data and metadata on the server to the server's disk or stable storage for the specified file. I don't understand why the client commits. I don't think that the "echo" shell built-in command runs fsync; if echo wrote to a local file and then the machine went down, the file might be lost. In contrast, the NFS client appears to be sending a COMMIT upon completion of the echo. Why? I am reluctant to use the async NFS server option, because it would apparently ignore COMMIT. I feel as if I had a local filesystem and I had to choose between syncing every file upon close and ignoring fsync altogether. What have I understood wrong?

  Read the article

• Windows Server 2008 Software Raid 5 - Data integrity issues

  - by Fopedush

  I've got a server running Windows Server 2008 R2, with a (windows native) software raid-5 array. The array consists of 7x 1TB Western Digital RE3 and RE4 drives. I have offline backups of this array. The problem is this: I noticed a few days ago after copying a large file to the disk that there was an integrity issue with that file - it was a ~12GB file that I had downloaded via uTorrent. After moving it to the raid array, I used uTorrent to relocate the download location, and performed a re-check so I could seed it from that location. The recheck found that only 6308/6310 chunks of the copied file were intact. My next step was to write a quick powershell script that would copy files to the array, while performing a SHA1 hash of the original and resultant files and comparing them. Smaller files (100-1000MB) copied over just fine. When I started copying larger data (~15GB), I found that the hash check failed about 2/3rds of the time. The corrupt files had very, very small inconsistencies - less than .01%. I further eliminated the possibility of networking or client issues by placing this large file on the C:\ of the server, and copying it repeatedly from there to the array, seeing similar results. Copying the data via explorer, powershell, or the standard windows command prompt yield the same results. None of the copies fail or report any problems. The raid array itself is listed as healthy in disk management. After a few experiments, I shut down the server and ran memtest overnight. No errors were detected. A basic run of chkdsk found no problems, but I did not use the /R flag, as I was unsure how that might affect a software raid-5 volume. I next ran Crystal Disk Info to check the smart data on the drives - but found that CDI only detected 5 out of 7 of the disks in the array. I have no idea why. Nevertheless, CDI shows the following "caution" flags on a single one of the drives: 05 199 199 140 000000000001 Reallocated Sectors Count C5 200 200 __0 000000000001 Current Pending Sector Count Which is a little bit alarming, but I don't really know what to do with the information. I hardly feel like one reallocated sector could be causing this. At this point, I'm looking for some guidance on what to do next. I need to determine the cause of this issue, but I'm hesitant to run chkdsk /R or any bootable disk health checkers because I'm afraid they might break the array. I've considered triggering a re-sync of the array, but I'm not actually sure how to do that without doing something silly like manually dropping a disk and then restoring it. Any advice that could help me ferret out the precise cause of this issue would be greatly appreciated.

  Read the article

• routing through multiple subinterfaces in debian

  - by Kstro21

  my question is as simple as the title, i have a debian 6 , 2 NICs, 3 different subnets in a single interface, just like this: auto eth0 iface eth0 inet static address 192.168.106.254 netmask 255.255.255.0 auto eth0:0 iface eth0:0 inet static address 172.19.221.81 netmask 255.255.255.248 auto eth0:1 iface eth0:1 inet static address 192.168.254.1 netmask 255.255.255.248 auto eth1 iface eth1 inet static address 172.19.216.3 netmask 255.255.255.0 gateway 172.19.216.13 eth0 is conected to a swith with 3 differents vlans, eth1 is conected to a router. No iptables DROP, so, all traffic is allowed. Now, passing the traffic through eth0 is OK, passing the traffic through eth0:0 is OK, but, passing the traffic through eth0:1 is not working, i can ping the ip address of that sub interface from a pc where this ip is the default gateway, but can't get to servers in the subnet of the eth1 interface, the traffic is not passing, even when i set the iptables to log all the traffic in the FORWARD chain and i can see the traffic there, but, the traffic is not really passing. And the funny is i can do any the other way around, i mean, passing from eth1 to eth0:1, RDP, telnet, ping, etc, doing some work with the iptable, i manage to pass some traffic from eth0:1 to eth1, the iptables look like this: iptables -t nat PREROUTING -d 192.168.254.1/32 -p tcp -m multiport --dports 25,110,5269 -j DNAT --to-destination 172.19.216.1 iptables -t nat PREROUTING -d 192.168.254.1/32 -p udp -m udp --dport 53 -j DNAT --to-destination 172.19.216.9 iptables -t nat PREROUTING -d 192.168.254.1/32 -p tcp -m tcp --dport 21 -j DNAT --to-destination 172.19.216.11 iptables -t nat POSTROUTING -s 172.19.216.0/24 -d 172.19.221.80/29 -j SNAT --to-source 172.19.221.81 iptables -t nat POSTROUTING -s 172.19.216.0/24 -d 192.168.254.0/29 -j SNAT --to-source 192.168.254.1 iptables -t nat POSTROUTING -s 172.19.216.0/24 -o eth0 -j SNAT --to-source 192.168.106.254 dong this is working, but,it is really a headache have to map each port with the server, imagine if i move the service from server, so, now i have doubts: can debian route through multiple subinterfaces?? exist a limit for this?? if not, what i'm doing wrong when i have the same setup with other subnets and it is working ok?? without the iptables rules in the nat, it doesn't work thanks and i hope good comments/answers

  Read the article

• Thinkpad speaker turns mute - Linux Codec issue?

  - by Curlew

  At some point a few days ago the speakers on my Lenovo Thinkpad T410 (Model number: 2537A11) suddenly stopped working randomly. This error happens every time I watch a video or listen to a music file. The sound just abruptly stops. At the moment, I can't produce a single sound no matter what I do. I am using Debian GNU/Linux on this laptop and there doesn't appear to be anything else wrong (the fan is working, no abnormal heat (staying around ~40°C), no other obvious errors or problems). Here is the output of a nice program someone pointed me to: martin@martin:~/Downloads$ sudo python run.py --monitor Using temporary directory: /dev/shm/hda-analyzer You may remove this directory when finished or if you like to download the most recent copy of hda-analyzer tool. Downloading file hda_analyzer.py Downloading file hda_guilib.py Downloading file hda_codec.py Downloading file hda_proc.py Downloading file hda_graph.py Downloading file hda_mixer.py Downloaded all files, executing hda_analyzer.py Watching 1 cards ====================================== Sound is working normally and then it stops and the following lines appear: Diff for codec 0/0 (0x14f15069): --- +++ @@ -164,17 +164,17 @@ Power: setting=D0, actual=D0 Node 0x1f [Pin Complex] wcaps 0x400501: Stereo Pincap 0x00000010: OUT Pin Default 0x901701f0: [Fixed] Speaker at Int N/A Conn = Analog, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT - Power: setting=D0, actual=D0 + Power: setting=D3, actual=D3 Connection: 2 0x10* 0x11 Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE And now there is also an error in the dmesg output hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj. I changed the bdl_pos_adj to various numbers (-1, 0, 64, 1024) and either there is no change at all or dmesg reports that the adjustment is too big. I wonder if this bdl_pos_adj is the real reason for the error. Here is my hardware information provided by alsa-info.sh website. Okay, i did some serious testing and even installed Windows and now i officially conclude that this is a hard-ware related issue with my Laptop speakers. Reason: The error occurs in my installed Debian Linux, an Ubuntu Live distribution and Windows XP No error-message appears in all of the OS. The sound just keeps running and i can't hear a thing. I tested different setups, including OSS, ALSA and the pulseaudio server on top If i use my new usb-headphones i can hear sound all the time without any sudden silences. So obviously, although hard to believe, my laptop speakers are not okay (never heard of similar cases). I'll award the bounty to anyone who can point me to good tutorials or the procedure how to exchange my T410 speakers (i still have warranty. The laptop was bought in Germany, but now i am in Denmark). Or to someone who can explain me the output from hda-analyzer (big log above).

  Read the article

• Is this distributed database server idea feasible?

  - by David

  I often use SQLite for creating simple programs in companies. The database is placed on a file server. This works fine as long as there are not more than about 50 users working towards the database concurrently (though depending on whether it is reads or writes). Once there are more than this, they will notice a slowdown if there are a lot of concurrent writing on the server as lots of time is spent on locks, and there is nothing like a cache as there is no database server. The advantage of not needing a database server is that the time to set up something like a company Wiki or similar can be reduced from several months to just days. It often takes several months because some IT-department needs to order the server and it needs to conform with the company policies and security rules and it needs to be placed on the outsourced server hosting facility, which screws up and places it in the wrong localtion etc. etc. Therefore, I thought of an idea to create a distributed database server. The process would be as follows: A user on a company computer edits something on a Wiki page (which uses this database as its backend), to do this he reads a file on the local harddisk stating the ip-address of the last desktop computer to be a database server. He then tries to contact this computer directly via TCP/IP. If it does not answer, then he will read a file on the file server stating the ip-address of the last desktop computer to be a database server. If this server does not answer either, his own desktop computer will become the database server and register its ip-address in the same file. The SQL update statement can then be executed, and other desktop computers can connect to his directly. The point with this architecture is that, the higher load, the better it will function, as each desktop computer will always know the ip-address of the database server. Also, using this setup, I believe that a database placed on a fileserver could serve hundreds of desktop computers instead of the current 50 or so. I also do not believe that the load on the single desktop computer, which has become database server will ever be noticable, as there will be no hard disk operations on this desktop, only on the file server. Is this idea feasible? Does it already exist? What kind of database could support such an architecture?

  Read the article

• How did what appears to be a virus get on my computer? (explanation of situation enclosed)

  - by Massimo

  My system is Windows XP SP3, updated with the latest patches. The PC is connected to a Cisco 877 ADSL router, which does NAT from the internal network to its single static public IP address. There are no forwarded ports, and the router's management console can only be accessed from the inside. I was doing two things: working on a remote office machine via VPN and browsing some web pages on the Cisco web site. The remote network is absolutely safe (it's a lab network, four virtual servers, no publicly accessible services and no users at all; also, none of what I'm going to describe ever happened there). The Cisco web site... well, I suppose is quite safe, too. Suddenly, something happened. Strange popups appears anywhere; programs claiming they're "antimalware", "antispyware" et so on begins autoinstalling; fake Windows Update and Security Center icons pop up in the system tray. svchost.exe began crashing repeatedly. Then, finally, after some minutes of this... BSOD. And, upon rebooting, BSOD again. Even in safe mode. Ok, that was obviously some virus/trojan/whatever. I had to install a new copy of Windows on another partition to clean things up. I found strange executables, services and DLLs almost anywhere. Amongst the other things, user32.dll and ndis.sys had been replaced. A fake software called "Antimalware Doctor" had been installed. There were services with completely random names or even GUIDs (!), and also ones called "IpSect" and "Darkness". There were executable files without an .exe extension. There were even two boot-class drivers, which I'm quite sure are the ones that finally caused the system to crash. A true massacre. Ok, now the questions: What the hell was that?!? It was something more than a simple virus! How did it manage to attack my computer, as I am behind a firewall and was not doing anything even only potentially harmful on the web at the time?

  Read the article

• System failure - need diagnostic recommendation

  - by Ladislav Mrnka

  I have big problem with my computer. Configuration is: Intel i7 + 6x2GB OCZ DDR3 Motheboard: Asus P6T Deluxe V2, HDD controller configured to AHCI Main drive: OCZ Vertex 2 (SSD) - contains all installed programs and system Second drive: Samsung SpinPoint - contains User profiles, ProgramData, virtual machines and databases Third drive: Samsung SpinPoint - data drive + backups OS: Windows 7 Ultimate x64 I have never had any problem with this computer until now. During weekend my computer completely crashed without any reason. Each time I tried to boot to Windows I got BSOD with message BAD_SYSTEM_CONFIG_INFO and automatic restart (I didn't install any new SW or HW). But after restart main OCZ drive was disconnected (not detected by BIOS). When I turned off and on computer, the drive was again connected. It also happend every single time I tried to repair installation somehow. It ended with some error and after restart drive was disconnected. The only thing which worked was format + fresh install. After installing almost everything I wanted to install Visual Studio 2010 Ultimate (complete installation without SQL Server Express). During installation of VS itself I always get BSOD - it is too fast so I'm not able to read description. After restart it searches for all disk drives for really long time and sometimes it changes boot drive so the system is not able to start - Bootmgr not found. After reconfiguring BIOS the system starts. There is no event describing the failure in Event viewer. Installing VS 2010 is absolutely necessary for me. I need help with diagnostic. I need to find where is the problem - I expect that the problem is in OCZ drive or in HDD controller on motherboard but I don't know how to find it. All components still have valid warranty. Can you recommend me some approach or tools to find the problem? Edit: I'm still looking for source of the problem. New information is that Windows are not able to perform check disk (Chkdsk) on the SSD system drive. After restarting it always starts checking drive and in part where files are checked it fails with BSOD - BAD_SYSTEM_CONFIG_INFO. After next restart and skipping check disk tests the system runs.

  Read the article

• Windows Server 2008 R2 loses ability to connect to network share

  - by JamesB

  I could sure use some help with this one: I've got two Windows Server 2008 R2 x64 Terminal Servers, as well as several 2003 servers (DNS / Wins / AD / DC). On the two 2008 boxes, every now and then they will get in this mode where you can't map a drive to a random server. I say random server because it's not always the same server that you can't map to. Here is a summary of what I can and can't do: net view \\servername Sometimes this works, sometimes it does not. net view \\FQDN This always works. net view \\IPAddress This always works. ping servername Sometimes this works, sometimes it does not. ping FQDN This always works. ping IPAddress This always works. I've been looking all over for a solution to this. It sure seems like Microsoft would have a hotfix by now. The kicker to this is that it sometimes works great, especially after a reboot. It may run for 2 weeks just fine, but all of a sudden it will fail to resolve the remote server name. It will then be this way for a few days, then it might start working again. Also, while it's in the mode of not working, the other servers have no problem getting there. It's just these 2008 R2 Terminal Servers. Setting a static entry in the Hosts file and LMHosts does not make it work. All servers have static IPs and they are registered in DNS and Wins just fine. Here is a long thread on MS Technet of the exact same problem, but they don't have a good solution. Here is their workaround (It was from June of 2010): Good news - a hotfix is in the works and a workaround has been identified: Root cause is that since this is SMB1 all user sessions are on a single TCP connection to the remote server. The first user to initiate a connection to the remote SMB server has their logon-ID added to the structure defining the connection. If that user logs off all subsequent uses of that TCP session fail as the logon-id is no longer valid. As a workaround for now to keep the issue from happening you will want to have the user not logoff the Terminal Server only disconnect their sessions. Any word from anyone out there about a solution? Any help would sure be appreciated. Thanks, James

  Read the article

• I want to virtualize my workstation (Tier 1), Looking for Bare Metal Hypervisor for consumer grade components

  - by Chase Florell

  I find myself in this similar bind at least once a year. The bind whereby I'm either upgrading a motherboard, or an OS hard drive. It drives me crazy to have to reinstall Windows, Visual Studio, all my addins, reconfigure my settings etc... every single time. I have a layout and I like and I want to stick with it. My question is... Is there a Bare Metal Hypervisor on the market that will enable me to virtualize my consumer grade workstation? I really want to avoid Host/Client virtualization. Bare Metal is definitely a better way to go for my needs. Is this a good approach, or am I going to suffer some other undesirable side effects by doing this? Clarification My machine has very limited purposes. My primary use is Visual Studio 2010 Professional where I develop ASP.NET MVC Web Applications. The second piece of software that I use (that's system intensive) is Photoshop CS3. Beyond that, my applications are limited to Outlook, Internet Explorer, Firefox, Opera, Chrome, LinqPad, and various other (small) apps. Beyond this, I'm considering working on a node.js project and might run ubuntu on the same hypervisor if possible. System Specs: Gigabyte Motherboard Intel i7 920 12 GB Ram basic 500GB 7200RPM HDD for OS 4 VelociRaptors in Raid 1/0 for build disk Dual GTS250 (512MB) Graphics cards (non SLI) for quad monitors On a side note I also wouldn't be opposed to an alternative suggestion if the limitations are too great. I could install the ESXi (or Zen Server) on my box, and build a separate "thin client" to RDP into the virtual machine. It appears as though RDP supports dual monitors. Edit (Dec 9, 2011) It's been nearly a year since I first asked this question. Since then, there have been a lot of great strides in Hypervisor technology... AND MokaFive is now released for corporate use. I'd love to dig into this question a little more and find out if there is a solid BareMetal Hypervisor for workstations running consumer grade components (IE: not Dell, HP, Lenovo, Etc).

  Read the article

< Previous Page | 652 653 654 655 656 657 658 659 660 661 662 663  | Next Page >